0805 COMMON MODE CHOKES Common Mode Chokes for Critical Applications • Eliminates virtually all common mode noise in high-speed, differential mode signal transmission applications such as USB 2.0, IEEE1394, HDMI and LVDS. • Most provide >25 dB common mode attenuation and >100 ohms impedance. Core material Ferrite Terminations Gold over nickel over silver-palladium-glass frit. Other terminations available at additional cost Weight 14.9 – 15.2 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +105°C with derated current Storage temperature Component: –55°C to +105°C. Tape and reel packaging: –55°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Packaging 2000 per 7″reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.14 mm pocket depth Part number1 Common mode impedance typ (Ohms) 10 MHz 100 MHz 500 MHz CP336FRA421MAZ 14 CP336FRA901MAZ 28 CP336FRA172MAZ 57 CP336FRA262MAZ 85 CP336FRA372MAZ118 CP336FRA502MAZ148 CP336FRA672MAZ246 CP336FRA902MAZ294 Common mode Inductance2 DCR max3 Isolation Irms4 attenuation typ (dB) 10 MHz 100 MHz 500 MHz min (nH) (Ohms) (Vrms) (mA) 42 70 90 154 170 303 260 435 370 641 500 945 670 1231 900 1715 1.1 2.3 8.4 1.4 4.2 16.9 2.3 6.7 22.0 3.0 8.6 27.8 4.5 11.9 34.3 4.9 14.5 31.3 8.4 16.6 30.0 8.7 18.7 30.5 1.When ordering, please specify termination and testing codes: CP336FRA902MAZ Termination:A= RoHS compliant gold over nickel over silverpalladium-glass frit Special order: C= Tin-lead over gold over nickel over silver-palladiumglass frit F= Tin-silver-copper over gold over nickel over silverpalladium-glass frit Testing:Z= COTS H= Screening per Coilcraft CP-SA-10001 2. Inductance measured at 100 MHz using an Agilent/HP 4286A impedance analyzer and a Coilcraft SMD-A fixture. 3.DCR is specified per winding. 4.Current per winding that causes a 20°C rise from 25°C ambient. 5. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 0.090 max 2,29 0.020 0.040 0,51 1,02 1 0.004 0,10 250500 250500 250500 250500 250 500 250 500 250 500 250 250 1 2 4 3 0.030 0,76 2 0.036 0,91 2 1 3 4 0.014 0,36 0.068 max 1,73 4 3 0.018 0,46 Recommended Land Pattern 0.020 0,51 inches mm ® © Coilcraft, Inc. 2012 0.12 0.17 0.25 0.26 0.32 0.37 0.45 0.65 0.065 max 1,65 Dimensions are in 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 23 47 84 147 189 273 322 413 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com Document CP306-1 Revised 09/07/12 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information. Document 306-2 0805 Common Mode Choke — CP336FRA Typical Attenuation (Ref: 50 Ohms) 0 5 10 -902 Attenuation (dB) -672 15 -502 -372 -262 20 -172 -901 -421 25 30 35 Common mode Differential mode (typical for all parts) 40 1 10 100 1000 Frequency (MHz) Typical Impedance vs Frequency 10000 -902 -672 -502 -372 -262 1000 Impedance (Ohms) -172 -901 -421 100 10 1 1 100 10 1000 Frequency (MHz) ® © Coilcraft, Inc. 2012 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email [email protected] www.coilcraft-cps.com Document CP306-2 Revised 09/07/12 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information.