CPC1020N Single Pole OptoMOS® Relay Parameter Blocking Voltage Load Current On-resistance, Max Rating 30 1.2 0.25 Description The CPC1020N is a 30V, single-pole, normally open (1-Form-A) Solid State Relay. The ultra-low on-resistance, 0.25Ω, of this relay allows for highcurrent operation. Clare's patented OptoMOS architecture makes available the optically coupled technology necessary to activate the output's efficient MOSFET switches while providing 1500Vrms inputto-output isolation. Control of the isolated output is accomplished by means of the highly effective GaAlAs infrared LED at the input. Units VP ADC Ω Features • Small 4-Pin SOP Package • Low Drive Power Requirements (TTL/CMOS Compatible) • No Moving Parts • High Reliability • Arc-Free With No Snubbing Circuits • 1500Vrms Input/Output Isolation • No EMI/RFI Generation • Machine Insertable, Wave Solderable • Tape & Reel Version Available Approvals • UL Recognized Component: File # E76270 • CSA Certified Component: Certificate # 1172007 • EN/IEC 60950-1 Compliant Ordering Information Applications • Sensor Circuitry • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment—Patient/Equipment Isolation • Aerospace • Industrial Controls Part # CPC1020N CPC1020NTR Description 4-Pin SOP (100/tube) 4-Pin SOP (2000/reel) Pin Configuration + Control – Control 1 4 Load 3 2 Load Switching Characteristics of Normally Open (Form A) Devices Control ILOAD + 90% 10%+ tOFF tON Pb RoHS 2002/95/EC DS-CPC1020N-R01 e3 www.clare.com 1 CPC1020N Absolute Maximum Ratings Parameter Blocking Voltage Input Power Dissipation 1 Input Control Current Peak (10ms) Reverse Input Voltage Total Power Dissipation 2 Isolation voltage, Input to Output Operational Temperature Storage Temperature Ratings 30 75 50 1 5 400 1500 -40 to +85 -40 to +125 Units VP mW mA A V mW Vrms °C °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. 1 Derate Linearly 1.33 mW / ºC Derate Linearly 3.33 mW / ºC Absolute Maximum Electrical Ratings are at 25ºC. 2 Electrical Characteristics Parameter Output Characteristics @ 25°C Load Current Continuous 1 Peak On-Resistance 2 Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics @ 25°C Input Control Current Input Dropout Current Input Voltage Drop Reverse Input Current Input/Output Characteristics @ 25°C Capacitance, Input to Output 1 2 Conditions Symbol Min Typ Max Units IF=2mA t < 10ms IL=1A VL=30V IL ILPK RON ILEAK - 0.116 - 1.2 3 0.25 1 ADC A Ω μA VL=15V; f=1MHz tON tOFF COUT - 0.48 0.65 70 3 3 - IL=1A IF=5mA VR=5V IF IF VF IR 0.1 0.9 - 0.13 1.2 - 2 1.4 10 mA mA V µA - CI/O - 3 - pF IF=5mA, VL=10V ms pF Load current derates linearly from 1.2A @ 25oC to 0.58A @85oC. Measurement taken within 1 second of on time. ESD Rating ESD Rating (Human Body Model) 1000 Volts 2 www.clare.com R01 CPC1020N PERFORMANCE DATA* 35 Typical LED Forward Voltage Drop (N=50, TA=25ºC, IF=5mA) Typical On-Resistance Distribution (N=50, TA=25ºC, IL=1A, IF=2mA) 20 25 20 15 10 15 Device Count (N) Device Count (N) Device Count (N) 30 25 10 5 5 0 0 0.113 Device Count (N) 10 10 1.2 1.0 -40 0.20 IF=5mA 10 0.60 0.47 Typical Turn-On Time vs. LED Forward Current (IL=100mA) 2.5 1.5 1.0 0.5 0.79 Typical Turn-Off Time vs. LED Forward Current (IL=100mA) 700 2.0 0.55 0.63 0.71 Turn-Off Time (ms) 680 660 640 620 IF=2mA 600 0 -20 0 20 40 60 Temperature (ºC) 80 0 100 Typical IF for Switch Operation vs. Temperature (IL=1A) 3.5 10 20 30 40 LED Forward Current (mA) 0 50 Typical Turn-On Time vs. Temperature (IL=100mA) 1.2 Turn-On Time (ms) 0.16 0.14 0.12 0.10 2.5 2.0 1.5 IF=2mA 1.0 IF=5mA 0.5 0 20 40 60 Temperature (ºC) 80 100 50 Typical Turn-Off Time vs. Temperature (IL=100mA) 1.0 0.9 0.8 IF=2mA 0.7 0.6 0.5 IF=5mA 0.4 0 -20 10 20 30 40 LED Forward Current (mA) 1.1 3.0 0.18 0.08 -40 0.45 0.50 0.55 Turn-On Time (ms) Turn-Off Time (ms) 1.1 0.40 Turn-Off Time (μs) 1.3 15 0 0.35 Turn On Time (ms) LED Forward Voltage (V) IF=50mA IF=20mA IF=10mA 20 5 0 1.6 39.4 25 0.133 Typical LED Forward Voltage Drop vs. Temperature 38.2 38.6 39.0 Blocking Voltage (VP) Typical Turn-Off Time Distribution (N=50, TA=25ºC, IL=5mA, IF=5mA) 30 5 1.4 5 37.8 15 5 1.5 10 0.118 20 0 LED Forward Current (mA) 0.114 0.115 0.116 0.117 On-Resistance (Ω) 25 15 0.101 0.109 0.117 0.125 LED Forward Current (mA) 15 Typical Turn-On Time Distribution (N=50, TA=25ºC, IL=5mA, IF=5mA) 20 0.093 20 0 1.29 Typical IF for Switch Operation (N=50, TA=25ºC, IL=100mA) 25 Device Count (N) 1.26 1.27 1.28 LED Forward Voltage (V) Device Count (N) 1.25 Typical Blocking Voltage Distribution (N=50, TA=25ºC) -40 -20 0 20 40 60 Temperature (ºC) 80 100 -40 -20 0 20 40 60 Temperature (ºC) 80 100 *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R01 www.clare.com 3 CPC1020N PERFORMANCE DATA* 0.40 0.5 0.0 -0.5 -1.0 0.20 -40 38.5 38.0 37.5 37.0 0 20 40 60 Temperature (ºC) 80 0 20 40 60 Temperature (ºC) 80 100 1.3 1.0 0.8 0.5 0.3 -40 100 -20 0 20 40 60 80 100 10s 100s Temperature (ºC) Energy Rating Curve 100 39.0 -20 -20 Typical Leakage Current vs. Temperature Measured Across Pins 3 & 4 (VL=30V, IF=0mA) 39.5 Typical Load Current vs. Temperature (IF=2mA) 0.0 0.10 Leakage Current (nA) Blocking Voltage (VP) 0.25 Typical Blocking Voltage vs. Temperature (IL=1μA) 40.0 36.5 -40 0.30 0.15 -1.5 -0.20 -0.15 -0.10 -0.05 0.00 0.05 0.10 0.15 0.20 Load Voltage (V) 40.5 0.35 1.5 Load Current (ADC) On-Resistance (Ω) Load Current (A) 1.0 Typical On-Resistance vs. Temperature (IL=0.5A, IF=2mA) 3.5 3.0 80 Current (A) 1.5 Typical Load Voltage vs. Load Current (TA=25ºC, IF=2mA) 60 40 2.5 2.0 1.5 1.0 20 0.5 0 -40 -20 0 20 40 60 Temperature (ºC) 80 100 0.0 10μs 100μs 1ms 10ms 100ms Time 1s *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com R01 CPC1020N MANUFACTURING INFORMATION Moisture Sensitivity Clare has characterized the moisture reflow sensitivity of this package, and has determined that this component must be handled in accordance with IPC/JEDEC standard J-STD-033 moisture sensitivity level (MSL), level 3 classification. Pb e3 RoHS 2002/95/EC Soldering Reflow Profile For proper assembly, the component must be processed in accordance with the current revision of IPC/JEDEC standard J-STD-020. Failure to follow the recommended guidelines may cause permanent damage to the device resulting in impaired performance and/or a reduced lifetime expectancy. Washing Clare does not recommend ultrasonic cleaning or the use of chlorinated solvents. MECHANICAL DIMENSIONS 4-Pin SOP Package Recommended PCB Land Pattern 4.089 ± 0.203 (0.161 ± 0.008) 0.200 ± 0.025 (0.008 ± 0.001) 6.096 ± 0.102 (0.240 ± 0.004) 3.810 ± 0.076 (0.150 ± 0.003) 0.60 (0.0217) 0.432 ± 0.127 (0.017 ± 0.005) 1.02 ± 0.025 (0.040 ± 0.001) Pin 1 2.54 Typ (0.100 Typ) 5.60 (0.2205) 1.30 (0.0512) 2.54 (0.10) 2.184 Max (0.086 Max) 0.0254 - 0.102 (0.001 - 0.004) Dimensions mm (inches) 0.381 TYP. (0.015 TYP.) Tape and Reel Packaging for 4-Pin SOP Package 330.2 Dia (13.00 Dia) Top Cover Tape Thickness 0.102 Max (0.004 Max) W=12.00 Max (0.472 Max) Pin 1 B0=4.70 (0.185) K0=2.70 (0.106) K1=2.30 (0.091) P=8.00 (0.315) A0=6.50 (0.256) User Direction of Feed Embossed Carrier Embossment Dimensions mm (inches) NOTE: Tape dimensions not shown comply with JEDEC Standard EIA-481-2 For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. 5 Specification: DS-CPC1020N-R01 ©Copyright 2008, Clare, Inc. OptoMOS® is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 8/29/08