VISHAY CRCW020124R3FNED

CRCW0201 e3
www.vishay.com
Vishay
Lead (Pb)-free Commodity Thick Film Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Pure tin solder contacts on Ni barrier layer
provides compatibility with lead (Pb)-free and
lead containing soldering processes
• Metal glaze on high quality ceramic
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P70
W
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
± 200
RESISTANCE
RANGE

10.0 to 10M
± 0.5
0.05
CRCW0201
0201
30
E96
- 200/+ 400
1.0 to 9.76
± 100
47.0 to 10M
± 200
SERIES
±1
10.0 to 10M
E24; E96
RR 0603M
- 200/+ 400
1.0 to 9.76
± 200
10.0 to 10M
±5
E24
- 200/+ 400
1.0 to 9.76
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. at 70 °C = 1.0 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
CRCW0201
W
0.05
Operating Voltage Umax. ACRMS/DC
V
30
Insulation Voltage Uins (1 min)
V
50
Insulation Resistance

> 109
Operating Temperature Range
°C
- 55 to + 155
Weight/1000 Pieces
mg
0.17
Rated Dissipation at 70 °C
(1)
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 06-Jun-12
Document Number: 20052
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW02011K00FNED
C
R
C
W
0
2
0
1
1
K
0
0
F
K
E
D
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
CRCW0201
R = Decimal
K = Thousand
M = Million
0000 = Jumper
D = ± 0.5 %
F = ± 1.0 %
J = ± 5.0 %
Z = Jumper
K = ± 100 ppm/K
N = ± 200 ppm/K
X = - 200 ppm/K/+ 400 ppm/K
0 = Jumper
ED
EE
EI
PRODUCT DESCRIPTION: CRCW0201 100 1K0 1 % ET7 e3
CRCW0201
100
562R
1%
ET7
e3
MODEL
TCR
RESISTANCE
VALUE
TOLERANCE
VALUE
PACKAGING
LEAD (Pb)-FREE
CRCW0201
± 200 ppm/K
± 100 ppm/K
- 200/+ 400 ppm/K
1R0 = 1 
10R = 10 
1K0 = 1 k
10K = 10 k
1M0 = 1 M
0R0 = Jumper
± 0.5 %
±1%
±5%
ET7
EF4
ET2
e3 = Pure tin
termination finish
PACKAGING
MODEL
CODE
QUANTITY
CARRIER TAPE
WIDTH
PITCH
REEL DIAMETER
ED = ET7
10 000
EI = ET2
20 000
8 mm
2 mm
254 mm/10"
EE = EF4
50 000
Paper tape acc.
to IEC 60068-3
Type I
CRCW0201
180 mm/7"
330 mm/13"
DIMENSIONS in millimeters
SIZE
DIMENSIONS
SOLDER PAD DIMENSIONS
INCH
METRIC
L
W
H
T1
0201
0603
0.6 ± 0.05
0.3 ± 0.05
0.23 ± 0.05
0.15 ± 0.05
T2
0.2
+ 0.05
- 0.10
a
b
l
0.28
0.43
0.23
Note
• No marking for 0201 size.
Revision: 06-Jun-12
Document Number: 20052
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
Fraction of Rated Dissipation P70 in %
DERATING
100
50
0
- 50
0
50
100
150
70
Ambient Temperature ϑamb in °C
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
Stability for product types:
CRCW0201 e3
1 to 10 M
4.5
-
Resistance
-
± 0.5 %; ± 1 %; ± 5 %
4.7
-
Voltage proof
U = 1.4 x Uins; 60 s
No flashover or breakdown
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Good tinning ( 95 % covered)
no visible damage
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C
(3 ± 0.3) s
Good tinning ( 95 % covered)
no visible damage
4.13
58 (Td)
Solderability
-
Temperature coefficient
(20/- 55/20) °C and
(20/125/20) °C
± 100 ppm/K,
± 200 ppm/K,
- 200 ppm/K/+ 400 ppm/K
4.32
21 (Uu3)
Shear
(adhesion)
9N
No visible damage
4.33
21 (Uu1)
Substrate bending
Depth 2 mm;
3 times
No visible damage,
no open circuit in bent position
± (0.5 % R + 0.05 )
4.8.4.2
30 min. at - 55 °C;
30 min. at 125 °C
4.19
14 (Na)
Revision: 06-Jun-12
Rapid change of temperature
5 cycles
± (0.5 % R + 0.05 )
1000 cycles
± (1 % R + 0.05 )
Document Number: 20052
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
Stability for product types:
CRCW0201 e3
4.23
-
Climatic sequence:
-
4.23.2
2 (Ba)
Dry heat
125 °C; 16 h
4.23.3
30 (Db)
Damp heat, cyclic
55 °C;  90 % RH;
24 h; 1 cycle
4.23.4
1 (Aa)
Cold
- 55 °C; 2 h
4.23.5
13 (M)
Low air pressure
1 kPa; (25 ± 10) °C; 1 h
4.23.6
30 (Db)
Damp heat, cyclic
55 °C;  90 % RH;
24 h; 5 cycles
4.23.7
-
DC load
U=
1 to 10 M
± (2 % R + 0.1 )
P 70 x R  Umax.
U = P 70 x R  Umax.;
1.5 h on; 0.5 h off;
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
± (2 % R + 0.1 )
70 °C; 8000 h
± (4 % R + 0.1 )
58 (Td)
Resistance to soldering heat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
± (1 % R + 0.05 )
4.35
-
Flamability, needle flame test
IEC 60695-11-5;
10 s
No burning after 30 s
4.24
78 (Cab)
Damp heat, steady state
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
± (2 % R + 0.1 )
-
Endurance at
upper category temperature
155 °C, 1000 h
± (2 % R + 0.1 )
45 (XA)
Component solvent resistance
Isopropyl alcohol;
50 °C; method 2
No visible damage
6 (Fc)
Vibration, endurance
by sweeping
f = 10 Hz to 2000 Hz;
x, y, z  1.5 mm;
A  200 m/s2;
10 sweeps per axis
± (0.5 % R + 0.05 )
4.18.2
4.25.3
4.29
4.22
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 06-Jun-12
Document Number: 20052
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
CRCW0201172RFNED CRCW0201499RFNED CRCW020113K3FNED CRCW020130K1FNED
CRCW020137K4FNED CRCW020140K2FNED CRCW020118K2FNED CRCW020119R6FNED
CRCW020121R0FNED CRCW0201330KJNED CRCW020134R8FNED CRCW020136K0FKED
CRCW020136R0FNED CRCW020142R2FNED CRCW020143R2FNED CRCW020147R0FKED
CRCW020149R9FKED CRCW0201680KJNED CRCW0201820KJNED CRCW020182K0JNED
CRCW020118R2FKED CRCW020151R0FKED CRCW020153R6FKED CRCW020156R2FKED
CRCW0201100RFKED CRCW0201172RFKED CRCW0201174RFKED CRCW0201200RFKED
CRCW02019K76FKED CRCW020111K0FKED CRCW020113K3FKED CRCW020130K0FKED
CRCW020137K4FKED CRCW020139K2FKED CRCW020140K2FKED CRCW02011M00FKED
CRCW020127R4FNED CRCW020144R2FNED CRCW020139R2FNED CRCW020130R1FNED
CRCW020124R3FNED CRCW020112R1FNED CRCW0201237KFKED CRCW0201261KFKED
CRCW02011K07FKED CRCW02011K10FKED CRCW02011K18FKED CRCW02011K20FKED
CRCW02011K21FKED CRCW02011K24FKED CRCW02011K33FKED CRCW02011K37FKED
CRCW02011K50FKED CRCW02011K54FKED CRCW02011K58FKED CRCW02011K60FKED
CRCW02011K91FKED CRCW02011K96FKED CRCW020110K5FKED CRCW020110K7FKED
CRCW0201105KFKED CRCW0201107RFKED CRCW020111K3FKED CRCW020111K5FKED
CRCW0201113RFKED CRCW0201115RFKED CRCW0201118RFKED CRCW020112K7FKED
CRCW0201120KFKED CRCW0201121KFKED CRCW0201121RFKED CRCW020113K0JNED
CRCW0201130RFKED CRCW0201130RJNED CRCW0201133RFKED CRCW0201137RFKED
CRCW020114K0FKED CRCW020114K3FKED CRCW020114K7FKED CRCW020114R0FNED
CRCW0201140RFKED CRCW0201143RFKED CRCW0201147RFKED CRCW020115K0FKED
CRCW0201150KFKED CRCW0201150RFKED CRCW0201154RFKED CRCW0201158KFKED
CRCW0201158RFKED CRCW020116K2FKED CRCW020116K5FKED CRCW0201160KJNED
CRCW0201162KFKED CRCW0201165RFKED CRCW0201174KFKED CRCW020118K2FKED
CRCW0201182KFKED CRCW0201187KFKED CRCW0201187RFKED CRCW020119K1FKED