CXP888P60 CMOS 8-bit Single Chip Microcomputer Description The CXP888P60 is a CMOS 8-bit micro-computer which consists of A/D converter, serial interface, timer/counter, time base timer, high precision timing pattern generation circuits, PWM output, VISS/ VASS circuit, 32kHz timer/counter, remote control receiving circuit, VSYNC separator and the measurement circuit which measure signals of capstan FG amplifier and drum FG/PG amplifier and other servo systems, as well as basic configurations like 8-bit CPU, PROM, RAM and I/O port. They are integrated into a single chip. Also, CXP888P60 provides sleep/stop function which enables to lower power consumption. The CXP888P60 is the PROM-incorporated version of the CXP88860 with built-in mask ROM. This provides the additional feature of being able to write directly into the program. Thus, it is most suitable for evaluation use during system development and for small-quantity production. 100 pin QFP (Plastic) Structure Silicon gate CMOS IC Features • A wide instruction set (213 instructions) which cover various types of data — 16-bit arithmetic/multiplication and division/boolean bit operation instructions • Minimum instruction cycle 250ns at 16MHz operation 122µs at 32kHz operation • Incorporated PROM capacity 60K bytes • Incorporated RAM capacity 1600 bytes (including PPG RAM) • Peripheral function — A/D converter 8 bits, 8 channels, successive approximation system (Conversion time of 20µs/16MHz) — Serial interface Incorporated 8-bit, 8-stage FIFO for data (Auto transfer for 1 to 8 bytes), 1 channel 8-bit clock sync type, 1 channel — Timer 8-bit timer/counter, 2 channels 19-bit time base timer 32kHz timer/counter — High precision timing pattern generation PPG 19 pins 32-stage programmable circuit RTG 5 pins, 1 channel 5-bit, 8-satge FIFO (RECCTL control), 1channel — PWM/DA gate output 12 bits, 2 channels (Repetitive frequency 62.5kHz/16MHz) DA gate pulse output, 13 bits, 2 channels — Analog signal input circuit Capstan FG amplifier circuit Drum FG amplifier circuit Drum PG amplifier circuit PBCTL amplifier circuit — CTL write/rewrite circuit Recording current control circuit — Servo input control Capstan FG, Drum FG/PG, CTL input — VSYNC separator — FRC capture unit Incorporated 26-bit and 8-stage FIFO — PWM output 14-bit, 1 channel — VISS/VASS circuit Pulse duty auto detection circuit — 32kHz timer/event counter 32kHz oscillation circuit, ultra-low speed instruction mode — Remote control reception circuit 8-bit pulse measurement counter, 6-stage FIFO — Tri-state output PPG 1 pin, output 8 pins — Pseudo HSYNC output function — High speed head switching circuit • Interruption 20 factors, 15 vectors, multi-interruption possible • Standby mode SLEEP/STOP • Package 100-pin plastic QFP Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E96107-ST 8 BIT TIMER/COUNTER1 8 BIT TIMER/COUNTER 0 CTL R/W CONTROL PSEUDO HSYNC GENERATOR HGO ADJ RECCTL CTLCIN 12 BIT PWM GENERATOR CH1 PWM1 DAA1 PULSE WIDTH COUNTER 12 BIT PWM GENERATOR CH0 VISS/VASS FIFO SERVO INPUT CONTROL REMOCON INPUT GAIN CONTROL AMP V SYNC SEPARATOR EC SELECT PWM0 DAA0 2 FIFO SERIAL INTERFACE UNIT (CH1) SERIAL INTERFACE UNIT (CH0) A/D CONVERTER AVDD PWM 14 AMPVDD 3 2 5 4 2 2 2 2 INT0 NMI INT1/NMI 2 CH0 VDD Vss Vpp EXTAL XTAL 32kHz TIMER/COUNTER PRESCALER/ TIME BASE TIMER RAM 1600 BYTES CLOCK GENERATOR/ SYSTEM CONTROL AA TEX TX RST MP FIFO CH1 REALTIME PULSE GENERATOR 5 RAM FIFO PROM 60K BYTES SPC700 CPU CORE 19 PROGRAMABLE PATTERN GENERATOR FRC CAPTURE UNIT INT2 INTERRUPT CONTROLLER AVREF 14 BIT PWM GENERATOR DDO RMC CFG DFG DPG CTLAMP EXI0 EXI1 SYNC TO EC SI1 SO1 SCK1 CS0 SI0 SO0 SCK0 AN0 to AN13 AVss AMPVSS PH0 to PH7 8 8 PI0 to PI7 PG0, 1 2 PF0 to PF3 PF4 to PF7 4 PE2 to PE5 PD0 to PD7 8 4 PC0 to PC7 8 PE0, 1, 6, 7 PB0 to PB7 8 4 PA0 to PA7 8 4 PORT G 2 PPO0 to PPO18 –2– RTO3 to RTO7 PORT A PORT B PORT C PORT D PORT E PORT F PORT H PORT I Block Diagram CXP888P60 CXP888P60 PE4/EXI0 PE3/SYNC PE1/SO1 PE2/SI1 PE0/SCK1 TEX TX VSS VDD Vpp PA7/PPO7 PA6/PPO6 PA5/PPO5 PA4/PPO4 PA3/PPO3 PA2/PPO2 PA0/PPO0/HGO PA1/PPO1 PB7/PPO15 PB6/PPO14 Pin Assignment (Top View) 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 PB5/PPO13 1 80 PE5/EXI1 PB4/PPO12 2 79 PE6/PWM0/DAA0 PB3/PPO11 3 78 PE7/PWM1/DAA1 PB2/PPO10 4 77 CFG PB1/PPO9 5 76 DFG PB0/PPO8 6 75 DPG PC7/RTO7 7 74 VREFOUT PC6/RTO6 8 73 AMPVSS PC5/RTO5 9 72 CTLSAMPI PC4/RTO4 10 71 CTLFAMPO PC3/RTO3 11 70 CTLAG PC2/PPO18 12 69 CTLAMP (+) PC1/PPO17 13 68 CTLAMP (–) PC0/PPO16 14 67 CTLCIN (–) PI7 15 66 CTLCIN (+) PI6 16 65 RECCTL (+) PI5 17 64 RECCTL (–) PI4 18 63 AMPVDD PI3 19 62 RECCAP PI2 20 61 VDD PI1/EC/INT2 21 60 AN0/ANOUT PI0/INT0/ENV-DET 22 59 AN1 PD7/SI0 23 58 AN2 PD6/SO0 24 57 AN3 PD5/SCK0 25 56 PF0/AN4 PD4/CS0 26 55 PF1/AN5 PD3/TO/DDO/ADJ/SRVO 27 54 AVDD PD2/PWM 28 53 AVREF PD1/RMC 29 52 AVSS PD0/INT1/NMI 30 51 PF2/AN6 Note) 1. Vpp (Pin 90) is always connected to VDD. 2. VDD (Pins 61 and 89) are both connected to VDD 3. Vss (Pins 41 and 88) are both connected to GND. 4. MP (Pin 39) must be connected to GND. –3– PF3/AN7 PF4/AN8 PF5/AN9 PF6/AN10 PF7/AN11 PG0/AN12 PG1/AN13 EXTAL XTAL VSS MP RST PH0 PH1 PH2 PH3 PH5 PH4 PH6 PH7 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 CXP888P60 Pin Description Symbol I/O PA0/PPO0 /HGO Output/Real-time output/Output PA1/PPO1 to PA7/PPO7 Output/ Real-time output Description (Port A) 8-bit output port. Data is gated with PPO contents by OR-gate and they are output. (8 pins) (Port B) 8-bit output port. Data is gated with PPO contents by OR-gate and they are output. Tri-state control is possible. (8 pins) Pseudo HSYNC output pin. Programmable pattern generator (PPG) output. Functions as high precision realtime pulse output port. (19 pins) PA0 can be tri-state controlled with PPG. PB0/PPO8 to PB7/PPO15 Output/ Real-time output PC0/PPO16 to PC2/PPO18 I/O/ Real-time output PC3/RTO3 to PC7/RTO7 I/O/ Real-time output PD0/INT1/ NMI I/O/Input/Input Input pin to request external interruption and non-maskable interruption. PD1/RMC I/O/Input Remote control receiving circuit input pin. PD2/PWM I/O/Output 14-bit PWM output pin. PD3 /TO DDO/ADJ SRVO PD4/CS0 I/O/Output/Output/ (Port D) 8-bit I/O port. I/O can be Output/Output set in a unit of single bits. (8 pins) I/O/Input PD5/SCK0 I/O/I/O Serial clock (CH0) I/O pin. PD6/SO0 I/O/Output Serial data (CH0) output pin. PD7/SI0 I/O/Input Serial data (CH0) input pin. PE0/SCK1 Output/I/O Serial clock (CH1) I/O pin PE1/SO1 Output/Output Serial data (CH1) output pin PE2/SI1 Input/Input PE3/SYNC Input/Input PE4/EXI0 Input/Input PE5/EXI1 Input/Input PE6/PWM0/ DAA0 Output/Output PE7/PWM1/ DAA1 Output/Output (Port C) 8-bit I/O port. I/O can be set in a unit of single bits. Data is gated with PPO or RT contents by OR-gate and they are output. (8 pins) Real-time pulse generator (RTG) output. Functions as high precision real-time pulse output port. (5 pins) Timer/counter, CTL duty detector, 32kHz oscillation adjustment and servo amplifier output pin. Serial chip select (CH0) input pin. Serial data (CH1) input pin (Port E) 8-bit port. Bits 2, 3, 4 and 5 Composite sync signal input pin. are for inputs; bits 0, 1, 6 and 7 are for outputs. External input pin for FRC capture unit. (8 pins) (2 pins) PWM output pin. (2 pins) –4– DA gate pulse output pin. (2 pins) CXP888P60 Description Description I/O Analog circuit internal waveform output pin. AN0/ANOUT Input/Output AN1 to AN3 Input PF0/AN4 to PF3/AN7 Input/Input PF4/AN8 to PF7/AN11 Output/Input PG0/AN12 PG1/AN13 Input/Input (Port G) 2-bit input port. (2 pins) Output (Port H) 8-bit output port; N-ch open drain output of medium drive voltage (12V) and large current (12mA). (8 pins) PH0 to PH7 PI0/INT0/ ENV-DET I/O/Input (Port F) Lower 4 bits are for inputs; upper 4 bits are for outputs. Lower 4 bits are standby release input pins. (8 pins) (Port I) 8-bit I/O port. I/O can be set in a unit of single bits. Function as standby release input can be set in a unit of single bits. (8 pins) Analog input pin for A/D converter. (14 pins) Input pin to request Trigger pulse input external interruption. pin for head Active when falling switching. edge. Input pin to request External event input external interruption. pin for timer/counter. Active when falling edge. PI1/EC/ INT2 I/O/Input/Input PI2 to PI7 I/O CFG Input Capstan FG input pin. DFG Input Drum FG input pin. DPG Input Drum PG input pin. RECCTL (+) RECCTL (–) I/O RECCTL signal output pin. (2 pins) CTLCIN (+) CTLCIN (–) Output Connected to RECCTL (+) and RECCTL (–) with the internal switch for playback. (2 pins) CTLAMP (+) CTLAMP(–) Input Input PBCTL signal with capacitor coupled. (2 pins) CTLFAMPO Output PBCTL signal 1st amplifier output. CTLSAMPI Input PBCTL signal 2nd amplifier input. RECCAP I/O Capacitor connecting pin for the slope setting of the CTL writing trapezoidal wave. VREFOUT Output Capacitor connecting pin for the VREF level smoothing of DPG, DFG and CFG. CTLAG Output Capacitor connecting pin for the CTL and AGND smoothing. PBCTL signal input pin. (2 pins) AMPVSS Analog signal input circuit GND pin. AMPVDD Analog signal input circuit power supply pin. –5– CXP888P60 Symbol I/O Description EXTAL Input XTAL Output TEX Input TX Output Connecting pin of crystal oscillator for 32kHz timer clock. When used as event counter, input to TEX pin and leave TX pin open. (In this time, feedback resistor is not removed.) RST Input System reset pin; Low level active. MP Input Test mode input pin. Always connect to GND. Positive power supply pin for A/D converter. AVDD AVREF Connecting pin of crystal oscillator for system clock. When supplying the external clock, input it to EXTAL pin and input the opposite phase clock to XTAL pin. Input Reference voltage input pin for A/D converter. AVSS GND pin for A/D converter. VDD Positive power supply pin. Vpp Positive power supply for incorporated PROM writing. Connect this pin to VDD for normal operation. VSS GND pin. Connect both Vss pins to GND. –6– CXP888P60 Input/Output Circuit Formats for Pins Pin Circuit format AA AA AA AA AAA AAA AAA Port A PA0/PPO0/ HGO 1 pin AAAA AAAA HOUT PPO0 MPX PA0 Data bus RD (Port A) HSEL HOUTE When reset AA AA Hi-Z MPX Output becomes active from high impedance by data writing to port. PPO1 PPG control status register bit 0 Tri-state control selection AAA AAA PPO1 PA1/PPO1 PA1 1 pin Data bus AA AA Hi-Z RD (Port A) Output becomes active from high impedance by data writing to port. AA AA Port A AAAA AAAA PPO data PA2/PPO2 to PA7/PPO7 Port A data Hi-Z Data bus RD (Port A) 6 pins Output becomes active from high impedance by data writing to port. Port B AAAA AAAA AAAA RTO data PB0/PPO8 to PB7/PPO15 Port B data Data bus RD (Port B) 8 pins Port B tri-state control –7– AA AA Hi-Z CXP888P60 Circuit format Pin Port C AAAA AAAA AAAA PC0/PPO16 to PC2/PPO18 PC3/RTO3 to PC7/RTO7 PPO, RTO data Port C data When reset AA AA AA AA Input protection circuit Port C direction Hi-Z IP Data bus RD (Port C) 8 pins AAAA AAAA AAAA AAAA RD (Port C direction) Port D Port D data PD0/INT1/ NMI PD1/RMC PD4/CS0 PD7/SI0 Port D direction Data bus RD (Port D) 4 pins AA AA A A IP Hi-Z Schmitt input PD1...Remote control circuit PD0...Interruption circuit PD4, 7...Serial CH0 Port D AAAA AAAA AA AAA AA AAA AA AAA Port D function select PD2/PWM PD3/TO/ DDO/ADJ/ SRVO PD2 ... 14-bit PWM PD3 ... Timer/counter, CTL duty detection circuit, 32kHz timer, amplifier circuit MPX Port D data Port D direction Data bus RD (Port D) 2 pins –8– AA AA AA AA IP Hi-Z CXP888P60 Pin AAAA AAAAAAA AAA AAA AAA AA AAA AAA AA AA Circuit format When reset Port D Port D function select PD5/SCK0 PD6/SO0 SI0 CH0 AA AA A MPX Port D data MPX Port D direction Data bus 2 pins Hi-Z IP Note) PD5 is schmitt input PD6 is inverter input RD (Port D) SI0, CH0 Port E AAAA AAAA AAAA AAAA AA AA AA AA Port/SCK output select PE0/SCK1 SI0 CH1 MPX Port E data Hi-Z control Data bus 1 pin SI0 CH1 RD (Port E) Port E AAAA AAAA AAAA AAAA AA AA AA AA Port E function select PE1/SO1 SI0 CH1 Data bus 1 pin Hi-Z IP AA AA MPX Port E data AA AA A A Hi-Z Hi-Z control RD (Port E) Port E PE2/SI1 PE3/SYNC PE4/EXI0 PE5/EXI1 AAAA Schmitt input PE2...SI0 CH1 PE3 PE4 Servo input PE5 IP Data bus RD (Port E) 4 pins –9– Hi-Z CXP888P60 Pin AAAA AAAA AAAA AAAA Circuit format Port E AA AA AA AA Port/DA/PWM select PE6/PWM0/ DAA0 PE7/PWM1/ DAA1 When reset DA gate output or PWM output AA AA MPX Port E data Data bus High level Hi-Z control 2 pins RD (Port E) Port E AA AA AA AA AAAA AAAA Input multiplexer AN0/ANOUT IP A/D converter Hi-Z From amplifier circuit Analog output control 1 pin AN1 to AN3 AA AA AAAA AAAA AAAA Input multiplexer 3 pin Port F PFO/AN4 to PF3/AN7 Hi-Z A/D converter IP Input multiplexer IP A/D converter Hi-Z Data bus 4 pins RD (Port F) Port F PF4/AN8 to PF7/AN11 AAAA AAAAA AAAAA AA AA AA AA Port F data Data bus RD (Port F) Port/AD select 4 pins Hi-Z IP Input multiplexer – 10 – A/D converter CXP888P60 Pin Circuit format Port G PG0/AN12 to PG1/AN13 AA AA AAAA Input multiplexer IP A/D converter Hi-Z Data bus 2 pins RD (Port G) AAA AAA AA AA Port H PH0 to PH7 When reset Medium drive voltage12 V Port H data Hi-Z Large current 12mA Data bus 8 pins AAAA AAAA AAAA AAAA RD (Port H) Port I Port I data PI0/INT0/ EVN-DET to PI1/EC/INT2 Port I direction Data bus AA AA AA AA IP AA AA AAAA AAAA AA AAAA AA AAAA AA AA AA AA RD (Port I) Edge detection Hi-Z Standby release Interruption circuit Data bus 2 pins RD (Port I direction) Port I Port I data PI2 to PI7 Port I direction IP Data bus RD (Port I) Edge detection Standby release Data bus 6 pins RD (Port I direction) – 11 – Hi-Z CXP888P60 Pin CTLAMP (+) CTLAMP (–) CTLFAMPO When reset Circuit format A AAA AAAA A AA A AA A AAA AAAAA AAAAA AAAAA AAAAA AA AA AAAA AA AA CTLAG CTLAMP (+) IP IP 1/2AMPVDD CTLFAMPO CTLAMP (–) 3 pins CTLSAMPI Input pin charge control Input pin charge control IP 1/2AMPVDD LPF circuit CTLAG 1 pin CFG DFG DPG AAAAA AAAAA AA AA AAAA AA AA Input pin charge control IP LPF circuit 1/2AMPVDD VREFOUT 3 pins AA AA AA AA AMPVDD CTLAG VREFOUT IP AMPVSS VREFOUT... CFG, DFG, DPG amplifiers CTLAG........ CTL amplifier 2 pins – 12 – 1/2AMPVDD CXP888P60 Pin When reset Circuit format AMPVDD AA AAAA AA AA AA Recording current control circuit Write current select RTO6 RECCTL (+) IP RTO7 Hi-Z CTLCIN (+) pin RTO3 AMPVSS 1 pin RTG control permission AMPVDD AA AAAA AA AA AA Recording current control circuit Write current select RTO7 RECCTL (–) IP RTO6 Hi-Z CTLCIN (–) pin RTO3 AMPVSS 1 pin RTG control permission AAA From RECCTL (+) pin IP CTLCIN (+) RTO3 Hi-Z RTG control permission 1 pin CTLCIN (–) AMPVSS AAA IP From RECCTL (–) pin RTO3 Hi-Z RTG control permission 1 pin AMPVSS RTG control permission RECCAP RTO5 AA A A IP 1 pin Recording current control circuit – 13 – Low level CXP888P60 Pin EXTAL XTAL 2 pins TEX TX 2 pins When reset Circuit format AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA EXTAL IP • Shows the circuit composition during oscillation. • Feedback resistor is removed and XTAL becomes High level during stop. Oscillation XTAL 32kHz timer/ counter TEX IP • Shows the circuit composition during oscillation. • Feedback resistor is removed during 32kHz oscillation circuit stop by software. At this time, TEX pin outputs Low level and TX pin outputs High level. Oscillation TX Pull-up resistor RST Schmitt input IP Power-on-reset circuit 1 pin – 14 – Low level CXP888P60 Absolute Maximum Ratings Item Supply voltage (Vss = 0V reference) Symbol Rating Unit VDD –0.3 to +7.0 V Vpp –0.3 to +13 V AVDD AVss to +7.0 ∗1 V AVSS –0.3 to +0.3 V AMPVDD AMPVSS to +7.0 ∗2 Remarks Incorporated PROM V V Input voltage VIN –0.3 to +0.3 –0.3 to +7.0 ∗3 Output voltage VOUT –0.3 to +7.0 ∗3 V Medium drive output voltage VOUTP –0.3 to +15.0 V High level output current IOH –5 mA High level total output current ∑IOH –50 mA Total of output pins IOL 15 mA IOLC 20 mA Other than large current output ports (value per pin) Large current output port ∗4 (value per pin) Low level total output current ∑IOL 130 mA Operating temperature Topr –10 to +75 °C Storage temperature Tstg –55 to +150 °C Allowable power dissipation PD 600 mW AMPVSS V Low level output current Port PH Total of output pins QFP package type ∗1) AVDD and VDD must not exceed +0.3V. ∗2) AMPVDD and VDD must not exceed +0.3V. ∗3) VIN and VOUT must not exceed VDD +0.3V. ∗4) The large current output port is port H (PH). Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should better take place under the recommended operating conditions. Exceeding those conditions may adversely affect the reliability of the LSI. – 15 – CXP888P60 Recommended Operating Conditions Item Symbol VDD Supply voltage Min. Max. 4.5 5.5 Guaranteed operation range for 1/2 and 1/4 frequency dividing clock 3.5 5.5 Guaranteed operation range for 1/16 frequency dividing clock or during SLEEP mode 2.7 5.5 2.5 5.5 High level input voltage Operating temperature V Remarks Guaranteed operation range by TEX clock Guaranteed data hold operation range during STOP AVDD 4.5 5.5 V ∗1 AMPVDD 4.5 5.5 V ∗2 VIH 0.7VDD VDD V ∗3 VIHS 0.8VDD VDD V VIHTS 2.2 VDD V VIHEX Low level input voltage Unit Vpp = VDD Vpp Analog power supply (Vss = 0V) VDD – 0.4 VDD + 0.3 V CMOS schmitt input ∗4 TTL schmitt input ∗5 EXTAL pin∗6 ∗3 TEX pin∗7 VIL 0 0.3VDD V VILS 0 0.2VDD V VILTS 0 0.8 V CMOS schmitt input ∗4 TTL schmitt input ∗5 VILEX –0.3 0.4 V EXTAL pin ∗6 Topr –10 +75 °C ∗1) ∗2) ∗3) ∗4) TEX pin ∗7 AVDD and VDD should be set to the same voltage. AMPVDD and VDD should be set to the same voltage. Normal input port (each pin of PC, PD2, PD3, PD6, PF0 to PF3, PG and PI2 to PI7), MP pin Each pin of RST, PD0/INT1/NMI, PD1/RMC, PD4/CS0, PD5/SCK0, PD7/SI0, PE0/SCK1, PE2/SI1, PE3/SYNC, PE4/EXI0, PE5/EXI1, PI0/INT0, PI1/EC/INT2 (For PE3/SYNC, when CMOS schmitt input is selected with mask option.) ∗5) PE3/SYNC ∗6) Specifies only during external clock input. ∗7) Specifies only during external event input. – 16 – CXP888P60 Electrical Characteristics DC Characteristics (VDD = 4.5 to 5.5V) Item High level output voltage Low level output voltage Symbol VOH VOL Pins PA to PD, PE0 to PE1, PE6 to PE7, PF4 to PF7, PH (VOL only) PI RST∗1 (VOL only) PD, PH IIHE EXTAL IILE Input current IIHT (Ta = –10 to +75°C, Vss = 0V reference) TEX IILT Conditions Min. Typ. Max. Unit VDD = 4.5V, IOH = –0.5mA 4.0 V VDD = 4.5V, IOH = –1.2mA 3.5 V VDD = 4.5V, IOL = 1.8mA 0.4 V VDD = 4.5V, IOL = 3.6mA 0.6 V VDD = 4.5V, IOL = 12.0mA 1.5 V VDD = 5.5V, VIH = 5.5V 0.5 40 µA VDD = 5.5V, VIL = 0.4V –0.5 –40 µA VDD = 5.5V, VIH = 5.5V 0.1 10 µA –0.1 –10 µA –1.5 –400 µA VDD = 5.5V, VIL = 0.4V IILR RST I/O leakage current IIZ PA to PG, PI, MP, AN0 to AN3, VDD = 5.5V, VI = 0, 5.5V ±10 µA Open drain output leakage current (N-CH Tr off state) ILOH PH VDD = 5.5V VOH = 12V 50 µA 35 45 mA 2.0 8 mA 50 100 µA 9 35 µA 30 µA 20 pF 16MHz crystal oscillation (C1 = C2 = 15pF) IDD1 VDD = 5.5V∗3 SLEEP mode IDDS1 VDD = 5.5V Supply current∗2 IDD2 IDDS2 32kHz crystal oscillation (C1 = C2 = 47pF) VDD, VSS VDD = 3.3V SLEEP mode VDD = 3V ± 0.3V IDDS3 STOP mode (EXTAL and TEX pins oscillation stop) VDD = 5V±0.5V Input capacity CIN PC, PD, PE0, PE2 to PE5 PF, PG, PI, RECCTL (+), RECCTL (–), Clock 1MHz CTLAMP (+), 0V other than the measured pins CTLAMP (–), CTLSAMPI, CFG, DFG, DPG 10 ∗1) RST pin specifies the low level input voltage only when the power-on-reset circuit is selected. ∗2) When entire output pins are open. ∗3) When setting upper 2 bits (CPU clock selection) of clock control register (CLC: 00FEH) to "00" and operating in high speed mode (1/2 frequency dividing clock). – 17 – CXP888P60 AC Characteristics (1) Clock timing (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pin Condition Min. System clock frequency fC XTAL EXTAL Fig. 1, Fig. 2 1 System clock input pulse width tXL, tXH XTAL EXTAL Fig. 1, Fig. 2 External clock drive 28 tCR, tCF tEH, tEL tER, tEF XTAL EXTAL Fig. 1, Fig. 2 External clock drive EC Fig. 3 EC Fig. 3 TEX TX VDD = 2.7 to 5.5V Fig. 2 (32kHz clock applied condition) TEX Fig. 3 TEX Fig. 3 System clock input rise and fall times Event count clock input pulse width Event count clock input rise and fall times System clock frequency fC Event count clock input pulse width tTL, tTH tTR, tTF Event count clock input rise and fall times Typ. Max. Unit 16 MHz ns 200 tsys + 200∗1 ns ns 20 ms kHz 32.768 µs 10 20 ms ∗1) tsys indicates three values according to the contents of the clock control register (CLC; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Fig. 1. Clock timing 1/fc VDD – 0.4V EXTAL XTAL 0.4V tCF tXH tXL tCR AAAA AAAAA AAAAA AAAA AAAAA AAAAA AAAA AAAAAAAAAA Fig. 2. Clock applied condition Crystal oscillation Ceramic oscillation EXTAL C1 EXTAL XTAL 32kHz clock applied condition Crystal oscillation External clock C2 TEX XTAL C1 74HC04 TX C2 Fig. 3. Event count clock timing 0.8VDD TEX EC 0.2VDD tEH tEF tEL tER tTH tTF tTL tTR – 18 – CXP888P60 (2) Serial transfer (CH0) Item (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Symbol Condition Pin Min. Max. Unit CS0 ↓ → SCK0 delay time tDCSK SCK0 Chip select transfer mode (SCK0 = output mode) tsys + 200 ns CS0 ↑ → SCK0 floating delay time tDCSKF SCK0 Chip select transfer mode (SCK0 = output mode) tsys + 200 ns CS0 ↓ → SO0 delay time tDCSO SO0 Chip select transfer mode tsys + 200 ns CS0 ↑ → SO0 floating delay time tDCSOF SO0 Chip select transfer mode tsys + 200 ns CS0 high level width tWHCS CS0 Chip select transfer mode tsys + 200 ns SCK0 cycle time tKCY Input mode 2tsys + 200 ns SCK0 16000/fc ns SCK0 high and low level widths tKH tKL Input mode tsys + 100 ns SCK0 Output mode 8000/fc – 50 ns SI0 input set-up time (against SCK0 ↑) tSIK SCK0 input mode 100 ns SI0 SCK0 output mode 200 ns SI0 input hold time (against SCK0 ↑) tKSI tsys + 200 ns SI0 100 ns SCK0 ↓ → SO0 delay time tKSO SO0 Output mode SCK0 input mode SCK0 output mode SCK0 input mode SCK0 output mode tsys + 200 ns 100 ns Note 1) tsys indicates three values according to the contents of the clock control register (CLC; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) The load of SCK0 output mode and SO0 output delay time is 50pF + 1TTL. – 19 – CXP888P60 Fig. 4. Serial transfer timing (CH0) tWHCS 0.8VDD CS0 0.2VDD tKCY tDCSK tKL tDCSKF tKH 0.8VDD 0.8VDD SCK0 0.2VDD tSIK tKSI 0.8VDD Input data SI0 0.2VDD tDCSO tKSO tDCSOF 0.8VDD SO0 Output data 0.2VDD – 20 – CXP888P60 Serial transfer (CH1) Item (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V) Symbol Pin tKCY SCK1 SCK1 high and low level widths tKH tKL SCK1 SI1 input set-up time (against SCK1 ↑) tSIK SI1 SI1 input hold time (against SCK1 ↑) tKSI SI1 SCK1 ↓ → SO1 delay time tKSO SO1 SCK1 cycle time Condition Min. Input mode Max. 1000 ns 16000/fc ns 400 ns 8000/fc – 50 ns SCK1 input mode 100 ns SCK1 output mode 200 ns SCK1 input mode 200 ns SCK1output mode 100 ns Output mode Input mode Output mode SCK1 input mode 200 ns SCK1 output mode 100 ns Note) The load of SCK1 output mode and SO1 output delay time is 50pF + 1TTL. Fig. 5. Serial transfer timing (CH1) tKCY tKL tKH 0.8VDD SCK1 0.2VDD tSIK tKSI 0.8VDD Input data SI1 Unit 0.2VDD tKSO 0.8VDD Output data SO1 0.2VDD – 21 – CXP888P60 (3) A/D converter characteristics (Ta = –10 to +75°C, VDD = AVDD = 4.5 to 5.5V, AVREF = 4.0 to AVDD, Vss = AVss = 0V reference) Item Symbol Pin Condition Min. Typ. Resolution Only for A/D converter operation Ta = 25°C VDD = AVDD = AVREF = 5.0V VDD = AVss = 0V Linearity error Absolute error Sampling time tCONV tSAMP Reference input voltage VREF AVREF Analog input voltage VIAN AN0 to AN7 Conversion time IREF 8 Bits ±1 LSB ±2 LSB µs 12/fADC ∗1 µs AVDD – 0.5 AVDD V 0 AVREF V 1.0 mA 10 µA 0.6 SLEEP mode STOP mode 32kHz operation mode AVREF Unit 160/fADC ∗1 Operation mode AVREF current Max. Fig. 6. Definitions of A/D converter terms Digital conversion value FFH FEH ∗1) fADC indicates the below values due to the contents of bit 0 (ADCCK) of the ADC operation clock selection register (MSC: 01FFH), bits 7 (PCK1) and 6 (PCK0) of the clock control register (address: 00FEH). Linearity error 01H 00H VFT VZT ADCCK Analog input PCK1, PCK0 0 (φ/2 selection) 1 (φselection) 00 (φ = fEX/2) fADC = fc/2 fADC = fc 01 (φ = fEX/4) fADC = fc/4 fADC = fc/2 11 (φ = fEX/16) fADC = fc/16 fADC = fc/8 – 22 – CXP888P60 (4) Interruption, reset input (Ta = –10 to +75°C, VDD = 4.5 to 5.5V, Vss = 0V reference) Item Symbol Pin Condition Min. Max. Unit External interruption high and low level widths tIH tIL INT0 INT1 INT2 NMI 1 µs Reset input low level width tRSL RST 32/fc µs Fig. 7. Interruption input timing tIH INT0 INT1 INT2 NMI (Falling edge) tIL 0.8VDD 0.2VDD Fig. 8. Reset input timing tRSL RST 0.2VDD – 23 – CXP888P60 Analog Circuit Characteristics (1) Amplifier circuit reference voltage characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V reference) Item Reference level output voltage Symbol VOR Pin Min. Typ. Max. Unit VREFOUT 2.2 2.4 2.6 V CTLAG 2.15 2.35 2.55 V VREFOUT = VREFOUT + 0.5V 3.50 6.5 mA VREFOUT = VREFOUT – 0.5V –0.30 –0.85 mA CTLAG = CTLAG + 0.5V 2.80 5.5 mA CTLAG = CTLAG – 0.5V –0.30 –0.85 mA VREFOUT Reference level output current IOR CTLAG Conditions (2) CTL 1st amplifier characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V, CTLAG reference) Item Voltage gain ∗1 Offset voltage Input resistance Charge switch ON resistance Symbol AVCTL1 Pin Min. Typ. Max. Unit Gain = 16dB RECCTL (–) = 0V 12.5 14.5 16.5 dB Gain = 27dB RECCTL (–) = 0V 23.5 25.5 27.5 dB RECCTL (+) Gain = 42dB CTLFAMPO∗2 RECCTL (–) = 0V 39.0 41.5 44.0 dB Gain = 58dB RECCTL (–) = 0V 54.5 57.0 59.5 dB CTLAMP (+) and CTLAMP (–) = open –40 0 +40 mV CTLAMP (+) Charge switch OFF CTLAMP (+) = +0.2V 26.0 44.5 kΩ CTLAMP (–) Charge switch OFF CTLAMP (–) = +0.2V 1.20 2.0 kΩ CTLAMP (+) Charge switch ON CTLAMP (+) = +0.5V 560 1010 Ω CTLAMP (–) Charge switch ON CTLAMP (–) = +0.5V 560 1010 Ω VOSCTL1 RINCTL1 RCCTL1 RECCTL and CTLCIN connection RREAD switch ON resistance CTLCIN 0V fix RWRITE switch ON resistance Conditions RECCTL (+) During CTL read operation, CTLCIN (+) CTLCIN (+) – RECCTL (+) = 0.2V 315 400 770 Ω RECCTL (–) During CTL read operation, CTLCIN (–) CTLCIN (–) – RECCTL (–) = 0.2V 315 400 770 Ω CTLCIN (+) During CTL write operation, CTLCIN (+) = AMPVSS + 0.2V 250 310 Ω CTLCIN (–) During CTL write operation, CTLCIN (–) = AMPVSS + 0.2V 250 310 Ω ∗1) When CTLCIN (+), CTLAMP (+) pins and CTLCIN (–), CTLAMP (–) pins are AC coupled, and then the signal is input from RECCTL (+) pin. ∗2) The result after measuring the CTLFAMPO output waveform or voltage gain. Note) The gain increases by approximately 1.5dB when the AC coupling capacitor (47µF) is connected to CTLAMP (+) and CTLAMP (–) pins, and the signal is input from CTLAMP (+) and CTLAMP (–) pins. – 24 – CXP888P60 (3) CTL 2nd amplifier characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V, CTLAG reference) Item Voltage gain∗1, ∗2 Symbol Pin Min. Typ. Max. Unit Gain = 5dB 4.8 5.8 6.8 dB Gain = 11dB 10.4 11.5 12.6 dB Gain = 16dB 15.3 16.5 17.7 dB Gain = 20dB 19.3 20.5 21.7 dB Conditions AVCTL2 LPF cut-off frequency ∗1, 2 fCCTL fDC – 3dB 15.0 25.0 40.0 kHz Offset voltage ∗2 VOSCTL2 CTLSAMPI = open –50 0 +50 mV Comparator level = +100mV0-p 70.0 100 130 mV0-p CTLSAMPI Comparator level = +250mV0-p 215 245 275 mV0-p Comparator level = +400mV0-p 370 400 430 mV0-p Comparator level = –100mV0-p –70.0 –100 –130 mV0-p Comparator level = –250mV0-p –220 –250 –280 mV0-p Comparator level = –400mV0-p –370 –400 –430 mV0-p 10.0 18.0 Comparator level ∗2 VCCTL Input resistance RINCTL2 Charge switch OFF CTLSAMPI = +0.2V Charge switch ON resistance RCCTL2 Charge switch ON CTLSAMPI = +0.5V 770 kΩ 1140 Ω ∗1) When the signal is input with the AC coupling capacitor (47µF) connected to CTLSAMPI pin. ∗2) The result after measuring the output waveform of amplifier internal low-pass filter or voltage value. (4) CTLAMP characteristics (1st amplifier + 2nd amplifier) (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V reference) Item Symbol Voltage gain ∗1 AVCTL Input amplitude (peak value) VPKCTL Input sensitivity VSCTL Input dead band VNSCTL Pin Conditions Min. Typ. Max. Unit CTL 1st amplifier gain = 16dB CTL 2nd amplifier gain = 20dB RECCTL (–) = 0V 31.8 35.0 38.2 dB ±300 mV0-p 0.10 mV0-p RECCTL (–) = 0V RECCTL (+) CTL 1st amplifier gain = 58dB CTL 2nd amplifier gain = 20dB Comparator level = +400mV0-p –400mV0-p 0.015 RECCTL (–) = 0V 0.08 0.04 mV0-p ∗1) As for other combinations of the amplifier gains, CTL 1st amplifier and CTL 2nd amplifier are added respectively. Note) The result when the signal is input from RECCTL (+) pin with CTL 1st amplifier + CTL 2nd amplifier after performing AC coupling of CTLCIN (+), CTLAMP (+) pins and CTLCIN (–), CTLAMP (–) pins, and CTLFAMPO, CTLSAMPI pins. – 25 – CXP888P60 (5) CFGAMP characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVDD = 0V, VREFOUT reference) Item Voltage gain ∗1, ∗2 LPF cut-off frequency ∗1, ∗2 Offset voltage ∗2 Comparator judgment level width ∗2 Input sensitivity ∗1 Input dead band ∗1 Symbol Pins Min. Typ. Max. Unit Gain = 0dB –0.3 0.6 2.2 dB Gain = 20dB 19.2 20.8 22.4 dB Gain = 34dB 33.2 34.8 36.4 dB Gain = 38dB 37.0 38.7 40.4 dB fCCFG fDC – 3dB 30.0 55.0 80.0 kHz VOSCFG CFG = open –50 0 +50 mV 260 320 360 mVp-p VCCFG Comparator schimitt width = 320mVp-p Comparator schimitt width = 160mVp-p 110 155 200 mVp-p Gain = 38dB Comparator level = 320mVp-p 4.20 5.00 mVp-p Gain = 38dB Comparator level = 160mVp-p 2.10 2.40 mVp-p AVCFG VSCFG VNSCFG CFG Conditions Gain = 38dB Comparator level = 320mVp-p 3.40 4.10 mVp-p Gain = 38dB Comparator level = 160mVp-p 1.50 2.00 mVp-p 5.5 8.3 kΩ Input resistance RINCFG Charge switch OFF CFG = +0.2V Charge switch ON resistance RCCFG Charge switch ON CFG = +0.5V Digital output DTYCFG waveform duty ∗1, ∗3 Input amplitude (peak value) ∗1 CFG = sine wave with 50% duty VPKCFG 48.0 455 710 Ω 50.0 52.0 % ±2.4 V0-p ∗1) When the signal is input with the AC coupling capacitor (47µF) connected to CFG pin. ∗2) The result after measuring the output waveform of amplifier internal low-pass filter or voltage value. ∗3) The result after measuring the digital signal waveform output from the amplifier circuit. – 26 – CXP888P60 (6) DFGAMP characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V, VREFOUT reference) Item Voltage gain ∗1, ∗2 LPF cut-off frequency ∗1, ∗2 Offset voltage ∗2 Comparator judgment level width ∗2 Input sensitivity ∗1 Input dead band ∗1 Symbol Pins Min. Typ. Max. Unit Gain = 0dB –0.3 0.6 2.2 dB Gain = 20dB 19.2 20.8 22.4 dB Gain = 34dB 33.2 34.8 36.4 dB Gain = 38dB 37.0 38.7 40.4 dB fCDFG fDC – 3dB 30.0 55.0 80.0 kHz VOSDFG DFG = open –50 0 +50 mV Comparator schmitt width = 320mVp-p 260 320 360 mVp-p Comparator schmitt width = 160mVp-p 110 155 200 mVp-p Gain = 38dB Comparator level = 320mVp-p 4.20 5.00 mVp-p Gain = 38dB Comparator level = 160mVp-p 2.10 2.40 mVp-p AVDFG VCDFG VSDFG VNSDFG DFG Conditions Gain = 38dB Comparator level = 320mVp-p 3.40 4.10 mVp-p Gain = 38dB Comparator level = 160mVp-p 1.50 2.00 mVp-p 5.5 8.3 kΩ Input resistance RINDFG Charge switch OFF DFG = +0.2V Charge switch ON resistance RCDFG Charge switch ON DFG = +0.5V Digital output waveform duty ∗1, 3 DTYDFG CFG = sine wave of 50% duty Input amplitude (peak value) ∗1 VPKDFG 48.0 455 710 Ω 50.0 52.0 % ±2.4 V0-p ∗1) When the signal is input with the AC coupling capacitor (47µF) connected to DFG pin. ∗2) The result after measuring the output waveform of amplifier internal low-pass filter or voltage value. ∗3) The result after measuring the digital signal waveform output from the amplifier circuit. – 27 – CXP888P60 (7) DPGAMP characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V, VREFOUT reference) Item Voltage gain ∗1, ∗2 LPF cut-off frequency ∗1, ∗2 Offset voltage ∗2 Comparator level ∗2 Input sensitivity ∗1 Input dead band ∗1 Symbol Pins Conditions AVDPG Min. Typ. Max. Unit 11.1 12.0 13.2 dB fCDPG fDC – 3dB 30.0 55.0 85.0 kHz VOSDPG DFG = open –35 0 +35 mV Comparator level = 600mV0-p 570 605 640 mV0-p Comparator level = 400mV0-p 370 400 432 mV0-p Comparator level = 200mV0-p 175 200 220 mV0-p Comparator level = 100mV0-p 72 100 125 mV0-p Comparator level = –600mV0-p –572 –605 –643 mV0-p Comparator level = –400mV0-p –368 –400 –438 mV0-p Comparator level = –200mV0-p –174 –200 –223 mV0-p Comparator level = –100mV0-p –71 –100 –124 mV0-p Comparator level = 600mV0-p, 200mV0-p 150 180 mV0-p Comparator level = 400mV0-p, 100mV0-p 100 120 mV0-p Comparator level = –600mV0-p, –200mV0-p –155 –185 mV0-p Comparator level = –400mV0-p, –100mV0-p –109 –130 mV0-p VCDPG VSDPG VNSDPG DPG Comparator level = 600mV0-p, 200mV0-p 113 142 mV0-p Comparator level = 400mV0-p, 100mV0-p 70 90 mV0-p Comparator level = –600mV0-p, –200mV0-p –120 –150 mV0-p Comparator level = –400mV0-p, –100mV0-p –80 –103 mV0-p 24.0 44.5 kΩ Input resistance RINDPG Charge switch OFF DPG = +0.2V Charge switch ON resistance RCDPG Charge switch ON DPG = +0.5V Input amplitude (peak value) ∗1 VPKDPG 450 860 Ω ±2.4 V ∗1) When the signal is input with the AC coupling capacitor (47µF) connected to DPG pin. ∗2) The result after measuring the output waveform of amplifier internal low-pass filter or voltage value. – 28 – CXP888P60 (8) CTL write circuit characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V reference) Item Output resistance Symbol Min. Typ. Max. Unit RECCAP = AMPVDD – 0.5V 450 625 1005 Ω RECCAP = AMPVDD + 0.5V 410 555 840 Ω Write current = 2.0mA 1.3 2.0 2.9 mA Write current = 2.5mA 1.7 2.5 3.7 mA Write current = 3.0mA 2.1 3.1 4.5 mA Write current = 3.5mA RECCTL (+) RECCTL (–) Write current = 4.0mA 2.6 3.6 5.2 mA 2.9 4.0 5.9 mA Write current = 4.5mA 3.3 4.6 6.6 mA Write current = 5.0mA 3.7 5.1 7.2 mA Write current = 5.5mA 4.0 5.6 8.0 mA Write current = 6.0mA 4.4 6.1 8.9 mA ROH ROL Output current ∗1 Pins IOREC RECCAP Conditions ∗1) The current value which flows when RECCTL (+) pin and RECCTL (–) pin are shorted. (9) Amplifier operating current characteristics (Ta = –10 to +75°C, VDD = AMPVDD = 5.0V, Vss = AMPVSS = 0V reference) Item Amplifier operating current Symbol Pins Conditions When the amplifier is operating ∗1 IAMP AMPVDD When the amplifier is not operating Min. Typ. Max. Unit 7.6 12.0 mA 10 µA ∗1) The CTL recording current is added during CTL write. Note) The amplifier operation and NOT-operation is controlled according to the contents of amplifier power supply control register (ASWC: 05E2H) bits 5, 4, 1 and 0. – 29 – CXP888P60 Supplement Fig. 9. Recommended oscillation circuit (i) AAAA AAAA AAAA EXTAL AAAA AAAA AAAA (ii) TEX XTAL Rd Rd C1 C2 Manufacturer RIVER ELETEC CO., LTD. Model HC-49/U03 TX C2 C1 fc (MHz) C1 (pF) C2 (pF) 8.00 10 10 5 5 8.00 16 (12) 16 (12) 10.00 16 (12) 16 (12) 12.00 12 12 16.00 12 12 32.768kHz 30 18 Rd (Ω) Circuit example 0 (i) 0 (i) 470k (ii) 10.00 12.00 16.00 KINSEKI LTD. HC-49/U (-S) P3 Mask option table Item Reset pin pull-up resistor Input circuit format∗1 Power-on-reset circuit Mask product CXP888P60Q-1- CXO888P60Q-2- Existent/Non-existent Existent Existent CMOS schmitt/ TTL schmitt TTL schmitt TTL schmitt Existent (CXP88616/24) Non-existent (CXP88732/40/48, CXP88852/60) Non-existent Existent ∗1) The input circuit format can be selected for PE3/SYNC pin. – 30 – CXP888P60 Characteristics Curve IDD vs. VDD IDD vs. fc (fc = 16MHz, Ta = 25°C, Typical) (VDD = 5.0V, Ta = 25°C, Typical) 35 100 1/2 dividing mode 1/2 dividing mode 1/4 dividing mode 30 1/16 dividing mode SLEEP mode 1 32kHz mode 0.1 32kHz SLEEP mode 25 IDD – Supply current [mA] IDD – Supply current [mA] 10 20 1/4 dividing mode 15 10 0.01 2 3 4 5 1/16 dividing mode 6 5 VDD – Supply voltage [V] SLEEP mode 0 5 10 15 16 fc – System clock [MHz] – 31 – 20 CXP888P60 Package Outline Unit: mm 100PIN QFP (PLASTIC) 23.9 ± 0.4 + 0.4 20.0 – 0.1 + 0.1 0.15 – 0.05 80 51 + 0.4 14.0 – 0.1 17.9 ± 0.4 15.8 ± 0.4 50 81 A 31 100 1 0.65 30 + 0.15 0.3 – 0.1 0.13 + 0.2 0.1 – 0.05 + 0.35 2.75 – 0.15 M 0° to 10° DETAIL A 0.8 ± 0.2 (16.3) 0.15 PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE QFP-100P-L01 LEAD TREATMENT SOLDER PLATING EIAJ CODE QFP100-P-1420 LEAD MATERIAL 42/COPPER ALLOY PACKAGE MASS 1.7g JEDEC CODE – 32 –