CYPRESS CY7C1355C

CY7C1379C
9-Mbit (256K x 32) Flow-through SRAM
with NoBL™ Architecture
Functional Description[1]
Features
• Can support up to 133-MHz bus operations with zero
wait states
— Data is transferred on every clock
• Pin compatible and functionally equivalent to ZBT™
devices
• Internally self-timed output buffer control to eliminate
the need to use OE
• Registered inputs for flow-through operation
The CY7C1379C is a 3.3V, 256K x 32 Synchronous
Flow-through Burst SRAM designed specifically to support
unlimited true back-to-back Read/Write operations without the
insertion of wait states. The CY7C1379C is equipped with the
advanced No Bus Latency™ (NoBL™) logic required to
enable consecutive Read/Write operations with data being
transferred on every clock cycle. This feature dramatically
improves the throughput of data through the SRAM, especially
in systems that require frequent Write-Read transitions.
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. The clock input is qualified by
the Clock Enable (CEN) signal, which when deasserted
suspends operation and extends the previous clock cycle.
Maximum access delay from the clock rise is 6.5 ns (133-MHz
device).
• Byte Write capability
• 256K x 32 common I/O architecture
• Single 3.3V power supply (VDD)
• Fast clock-to-output times
— 6.5 ns (for 133-MHz device)
Write operations are controlled by the two Byte Write Select
(BW[A:D]) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
• Clock Enable (CEN) pin to suspend operation
• Synchronous self-timed writes
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. In order to avoid bus
contention, the output drivers are synchronously tri-stated
during the data portion of a write sequence.
• Asynchronous Output Enable
• Available in JEDEC-standard lead-free 100-Pin TQFP,
lead-free and non lead-free 165-Ball FBGA package
• Burst Capability—linear or interleaved burst order
• Low standby power
Logic Block Diagram–CY7C1379C (256K x 36)
ADDRESS
REGISTER
A0, A1, A
A1
D1
A0
D0
MODE
CLK
CEN
C
CE
ADV/LD
C
BURST
LOGIC
Q1 A1'
A0'
Q0
WRITE ADDRESS
REGISTER
ADV/LD
BWA
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BWB
BWC
WRITE
DRIVERS
MEMORY
ARRAY
S
E
N
S
E
A
M
P
S
BWD
WE
OE
CE1
CE2
CE3
INPUT
REGISTER
D
A
T
A
S
T
E
E
R
I
N
G
O
U
T
P
U
T
B
U
F
F
E
R
S
DQs
E
E
READ LOGIC
ZZ
SLEEP
Control
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05688 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised September 14, 2006
CY7C1379C
Selection Guide
133 MHz
100 MHz
Unit
Maximum Access Time
6.5
7.5
ns
Maximum Operating Current
250
180
mA
Maximum CMOS Standby Current
40
40
mA
Pin Configurations
Document #: 38-05688 Rev. *D
A
A
OE
86
81
CEN
87
82
WE
88
A
CLK
89
83
VSS
90
ADV/LD
VDD
91
NC(18M)
CE3
92
84
BWA
93
85
BWC
BWD
96
BWB
CE2
97
94
A
CE1
98
A
99
95
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
A
A
A
A1
A0
NC
NC
VSS
VDD
NC(72M)
NC(36M)
A
A
A
A
A
A
A
CY7C1379C
A
BYTE D
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
BYTE C
NC
DQC
DQC
VDDQ
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
VSS/DNU
VDD
NC
VSS
DQD
DQD
VDDQ
VSS
DQD
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
NC
100
100-Pin TQFP Pinout
NC
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
NC
BYTE B
BYTE A
Page 2 of 15
CY7C1379C
Pin Configurations (continued)
165-Ball FBGA Pinout
CY7C1379C (256K x 32)
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
1
A
CE1
BWC
BWB
CE3
CEN
ADV/LD
A
A
NC
NC/1G
A
CE2
BWD
BWA
CLK
WE
OE
NC/18M
A
NC
NC
DQC
NC
DQC
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDDQ
VDDQ
VDDQ
NC
DQB
NC
DQB
R
MODE
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
DQC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQB
DQB
DQC
NC
DQD
DQC
VDD
DQD
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
NC
VDDQ
DQB
NC
DQA
DQB
ZZ
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
DQD
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQA
DQA
DQD
NC
DQD
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
VDD
VSS
VDDQ
VDDQ
DQA
NC
DQA
NC
A
A
NC
NC
A1
VSS
NC
NC
A
A
A
NC/288M
A
A
NC
A0
NC
A
A
A
A
NC/144M NC/72M
NC/36M
Pin Definitions
Name
TQFP
FBGA
37,36,32,33,34,3
5,44,45,46,
47,48,49,50,81,8
2,83,99,100
R6,P6,A2,
A9,A10,B2
B10,P3,P4,
P8,P9,P10,
R3,R4,R8,
R9,R10,R11
InputAddress Inputs used to select one of the 256K address
Synchronous locations. Sampled at the rising edge of the CLK. A[1:0] are fed
to the two-bit burst counter.
93,94,95,96
B5,A5,A4,
B4
InputByte Write Inputs, active LOW. Qualified with WE to conduct
Synchronous writes to the SRAM. Sampled on the rising edge of CLK.
WE
88
B7
InputWrite Enable Input, active LOW. Sampled on the rising edge
Synchronous of CLK if CEN is active LOW. This signal must be asserted LOW
to initiate a write sequence.
ADV/LD
85
A8
InputAdvance/Load Input. Used to advance the on-chip address
Synchronous counter or load a new address. When HIGH (and CEN is
asserted LOW) the internal burst counter is advanced. When
LOW, a new address can be loaded into the device for an access.
After being deselected, ADV/LD should be driven LOW in order
to load a new address.
CLK
89
B6
CE1
98
A3
InputChip Enable 1 Input, active LOW. Sampled on the rising edge
Synchronous of CLK. Used in conjunction with CE2, and CE3 to select/deselect
the device.
CE2
97
B3
InputChip Enable 2 Input, active HIGH. Sampled on the rising edge
Synchronous of CLK. Used in conjunction with CE1 and CE3 to select/deselect
the device.
CE3
92
A6
InputChip Enable 3 Input, active LOW. Sampled on the rising edge
Synchronous of CLK. Used in conjunction with CE1 and CE2 to select/deselect
the device.
A0, A1, A
BWA, BWB,
BWC, BWD
Document #: 38-05688 Rev. *D
I/O
Input-Clock
Description
Clock Input. Used to capture all synchronous inputs to the
device. CLK is qualified with CEN. CLK is only recognized if CEN
is active LOW.
Page 3 of 15
CY7C1379C
Pin Definitions (continued)
Name
TQFP
FBGA
OE
86
B8
InputOutput Enable, asynchronous input, active LOW. Combined
Asynchronous with the synchronous logic block inside the device to control the
direction of the I/O pins. When LOW, the I/O pins are allowed to
behave as outputs. When deasserted HIGH, I/O pins are
tri-stated, and act as input data pins. OE is masked during the
data portion of a write sequence, during the first clock when
emerging from a deselected state, when the device has been
deselected.
CEN
87
A7
InputClock Enable Input, active LOW. When asserted LOW the
Synchronous Clock signal is recognized by the SRAM. When deasserted
HIGH the Clock signal is masked. Since deasserting CEN does
not deselect the device, CEN can be used to extend the previous
cycle when required.
ZZ
64
H11
InputZZ “sleep” Input. This active HIGH input places the device in a
Asynchronous non-time critical “sleep” condition with data integrity preserved.
For normal operation, this pin has to be LOW or left floating. ZZ
pin has an internal pull-down.
52,53,56,57,
58,59,62,63,
68,69,72,73,
74,75,78,79,
2,3,6,7,
8,9,12,13,
18,19,22,23,
24,25,28,29
M11,L11,
K11,J11,
J10,K10,
L10,M10,
D10,E10,
F10,G10,
D11,E11,
F11,G11,
D1,E1,F1,
G1,D2,E2,
F2,G2,J1,
K1,L1,M1,
J2,K2,L2
M2
I/OBidirectional Data I/O Lines. As inputs, they feed into an
Synchronous on-chip data register that is triggered by the rising edge of CLK.
As outputs, they deliver the data contained in the memory
location specified by address during the clock rise of the Read
cycle. The direction of the pins is controlled by OE and the
internal control logic. When OE is asserted LOW, the pins can
behave as outputs. When HIGH, DQs are placed in a tri-state
condition. The outputs are automatically tri-stated during the
data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is
deselected, regardless of the state of OE.
31
R1
15,41,65,91
D4,D8,E4,
E8,F4,F8,
G4,G8,H2,
H4,H8,J4,
J8,K4,K8,
L4,L8,M4,
M8
4,11,20,27,54,
61,70,77
C3,C9,D3,
D9,E3,E9,
F3,F9,G3,
G9,J3,J9,
K3,K9,L3,
L9,M3,M9,
N3,N9
DQs
Mode
VDD
VDDQ
Document #: 38-05688 Rev. *D
I/O
Input
Strap Pin
Description
Mode Input. Selects the burst order of the device.
When tied to GND selects linear burst sequence. When tied to
VDD or left floating selects interleaved burst sequence.
Power Supply Power supply inputs to the core of the device.
I/O Power
Supply
Power supply for the I/O circuitry.
Page 4 of 15
CY7C1379C
Pin Definitions (continued)
Name
VSS
NC
VSS/DNU
TQFP
FBGA
I/O
5,10,17,21,
26,40,55,60,
67,71,76,90,
C4,C5,C6,
C7,C8,D5,
D6,D7,E5,
E6,E7,F5,
F6,F7,G5,
G6,G7,H5,
H6,H7,J5,
J6,J7,K5,K6,K
7,L5,L6,L7,M5
,M6,M7,
N4,N8
Ground
1,16,30,38,39,
A1,A11,B1,
42,43,51,66,80,8 B9,B11,C1,
4,95,96
C2,C10,C11,H
1,H3,H9,
H10,N1,N2,
N5,N6,N7
N10,N11,P1,P
2,P5,P7,
P11,R2,R5,
R7
14
-
–
Ground/DNU
Functional Overview
The CY7C1379C is a synchronous flow-through burst SRAM
designed specifically to eliminate wait states during
Write-Read transitions. All synchronous inputs pass through
input registers controlled by the rising edge of the clock. The
clock signal is qualified with the Clock Enable input signal
(CEN). If CEN is HIGH, the clock signal is not recognized and
all internal states are maintained. All synchronous operations
are qualified with CEN. Maximum access delay from the clock
rise (tCDV) is 6.5 ns (133-MHz device).
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If Clock
Enable (CEN) is active LOW and ADV/LD is asserted LOW,
the address presented to the device will be latched. The
access can either be a read or write operation, depending on
the status of the Write Enable (WE). BW[A:D] can be used to
conduct byte write operations.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion.
All operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD should be driven LOW once the device has been
deselected in order to load a new address for the next
operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, (3) the Write Enable input
signal WE is deasserted HIGH, and 4) ADV/LD is asserted
LOW. The address presented to the address inputs is latched
into the Address Register and presented to the memory array
and control logic. The control logic determines that a read
Document #: 38-05688 Rev. *D
Description
Ground for the device.
No Connects. Not Internally connected to the die.
18M, 36M, 72M, 144M, 288M, 576M, and 1G are address
expansion pins and are not internally connected to the die.
This pin can be connected to Ground or should be left floating.
access is in progress and allows the requested data to
propagate to the output buffers. The data is available within 6.5
ns (133-MHz device) provided OE is active LOW. After the first
clock of the read access, the output buffers are controlled by
OE and the internal control logic. OE must be driven LOW in
order for the device to drive out the requested data. On the
subsequent clock, another operation (Read/Write/Deselect)
can be initiated. When the SRAM is deselected at clock rise
by one of the chip enable signals, its output will be tri-stated
immediately.
Burst Read Accesses
The CY7C1379C has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to
four Reads without reasserting the address inputs. ADV/LD
must be driven LOW in order to load a new address into the
SRAM, as described in the Single Read Access section above.
The sequence of the burst counter is determined by the MODE
input signal. A LOW input on MODE selects a linear burst
mode, a HIGH selects an interleaved burst sequence. Both
burst counters use A0 and A1 in the burst sequence, and will
wrap around when incremented sufficiently. A HIGH input on
ADV/LD will increment the internal burst counter regardless of
the state of chip enable inputs or WE. WE is latched at the
beginning of a burst cycle. Therefore, the type of access (Read
or Write) is maintained throughout the burst sequence.
Single Write Accesses
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the Write signal WE
is asserted LOW. The address presented to the address bus
is loaded into the Address Register. The write signals are
latched into the Control Logic block. The data lines are
automatically tri-stated regardless of the state of the OE input
signal. This allows the external logic to present the data on
DQs.
Page 5 of 15
CY7C1379C
On the next clock rise the data presented to DQs (or a subset
for Byte Write operations, see Truth Table for details) inputs is
latched into the device and the write is complete. Additional
accesses (Read/Write/Deselect) can be initiated on this cycle.
The data written during the Write operation is controlled by
BW[A:D] signals. The CY7C1379C provides Byte Write
capability that is described in the truth table. Asserting the
Write Enable input (WE) with the selected Byte Write Select
input will selectively write to only the desired bytes. Bytes not
selected during a Byte Write operation will remain unaltered.
A synchronous self-timed write mechanism has been provided
to simplify the Write operations. Byte Write capability has been
included in order to greatly simplify Read/Modify/Write
sequences, which can be reduced to simple Byte Write operations.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, and CE3, must remain inactive for
the duration of tZZREC after the ZZ input returns LOW.
Linear Burst Address Table
(MODE = GND)
Because the CY7C1379C is a common I/O device, data
should not be driven into the device while the outputs are
active. The Output Enable (OE) can be deasserted HIGH
before presenting data to the DQ inputs. Doing so will tri-state
the output drivers. As a safety precaution, DQs and DQPX.are
automatically tri-stated during the data portion of a write cycle,
regardless of the state of OE.
Burst Write Accesses
The CY7C1379C has an on-chip burst counter that allows the
user the ability to supply a single address and conduct up to
four Write operations without reasserting the address inputs.
ADV/LD must be driven LOW in order to load the initial
address, as described in the Single Write Access section
above. When ADV/LD is driven HIGH on the subsequent clock
rise, the Chip Enables (CE1, CE2, and CE3) and WE inputs are
ignored and the burst counter is incremented. The correct
BW[A:D] inputs must be driven in each cycle of the burst write,
in order to write the correct bytes of data.
First
Address
A1, A0
Second
Address
A1, A0
Third
Address
A1, A0
Fourth
Address
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Interleaved Burst Sequence
First
Address
Second
Address
Third
Address
Fourth
Address
A1, A0
A1, A0
A1, A0
A1, A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min.
Max.
Unit
IDDZZ
Sleep mode standby current
ZZ > VDD − 0.2V
50
mA
tZZS
Device operation to ZZ
ZZ > VDD − 0.2V
2tCYC
ns
tZZREC
ZZ recovery time
ZZ < 0.2V
tZZI
ZZ Active to Sleep current
This parameter is sampled
tRZZI
ZZ inactive to exit Sleep current
This parameter is sampled
Document #: 38-05688 Rev. *D
2tCYC
ns
2tCYC
0
ns
ns
Page 6 of 15
CY7C1379C
Truth Table[2, 3, 4, 5, 6, 7, 8]
Operation
ADRESS
Used
CE1 CE2 CE3 ZZ ADV/LD WE
BWX OE CEN CLK
DQ
Deselect Cycle
None
H
X
X
L
L
X
X
X
L
L->H
Tri-State
Deselect Cycle
None
X
X
H
L
L
X
X
X
L
L->H
Tri-State
Deselect Cycle
None
X
L
X
L
L
X
X
X
L
L->H
Tri-State
Continue Deselect Cycle
READ Cycle (Begin Burst)
None
X
X
X
L
H
X
X
X
L
L->H
Tri-State
External
L
H
L
L
L
H
X
L
L
L->H
Data Out (Q)
Next
READ Cycle (Continue Burst)
X
X
X
L
H
X
X
L
L
L->H
Data Out (Q)
NOP/DUMMY READ (Begin Burst) External
L
H
L
L
L
H
X
H
L
L->H
Tri-State
DUMMY READ (Continue Burst)
Next
X
X
X
L
H
X
X
H
L
L->H
Tri-State
External
L
H
L
L
L
L
L
X
L
L->H
Data In (D)
WRITE Cycle (Continue Burst)
Next
X
X
X
L
H
X
L
X
L
L->H
Data In (D)
NOP/WRITE ABORT (Begin Burst)
None
L
H
L
L
L
L
H
X
L
L->H
Tri-State
WRITE Cycle (Begin Burst)
WRITE ABORT (Continue Burst)
IGNORE CLOCK EDGE (Stall)
Sleep MODE
Next
X
X
X
L
H
X
H
X
L
L->H
Tri-State
Current
X
X
X
L
X
X
X
X
H
L->H
–
None
X
X
X
H
X
X
X
X
X
X
Tri-State
Truth Table for Read/Write[2, 3]
Function (CY7C1379C)
WE
BWA
BWB
BWC
BWD
Read
H
X
X
X
X
Write No Bytes Written
L
H
H
H
H
Write Byte A – (DQA)
L
L
H
H
H
Write Byte B – (DQB)
Write Byte C – (DQC)
L
H
L
H
H
L
H
H
L
H
Write Byte D – (DQD)
L
H
H
H
L
Write All Bytes
L
L
L
L
L
Notes:
2. X =”Don't Care.” H = HIGH, L = LOW. BWx = 0 signifies at least one Byte Write Select is active, BWx = Valid signifies that the desired byte write selects are
asserted, see Truth Table for details.
3. Write is defined by BWX, and WE. See Truth Table for Read/Write.
4. When a Write cycle is detected, all I/Os are tri-stated, even during Byte Writes.
5. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
6. CEN = H, inserts wait states.
7. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs = Three-state when OE is inactive
or when the device is deselected, and DQs = data when OE is active.
Document #: 38-05688 Rev. *D
Page 7 of 15
CY7C1379C
Maximum Ratings
DC Input Voltage ................................... –0.5V to VDD + 0.5V
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current.................................................... > 200 mA
Operating Range
Supply Voltage on VDD Relative to GND........ –0.5V to +4.6V
Supply Voltage on VDDQ Relative to GND ...... –0.5V to +VDD
DC Voltage Applied to Outputs
in High-Z State .................................... –0.5V to VDDQ + 0.5V
Range
Ambient
Temperature (TA)
VDD/VDDQ
0°C to +70°C
3.3V – 5%/+10%
Com’l
Ind’l
–40°C to +85°C
Electrical Characteristics Over the Operating Range [9, 10]
Parameter
Description
Test Conditions
Min.
Max.
Unit
3.135
3.6
V
3.135
VDD
V
VDD
Power Supply Voltage
VDDQ
I/O Supply Voltage
for 3.3V I/O
VOH
Output HIGH Voltage
for 3.3V I/O, IOH = –4.0 mA
VOL
Output LOW Voltage
for 3.3V I/O, IOL = 8.0 mA
0.4
V
VIH
Input HIGH Voltage
for 3.3V I/O
2.0
VDD + 0.3V
V
for 3.3V I/O
Voltage[9]
2.4
V
VIL
Input LOW
–0.3
0.8
V
IX
Input Leakage Current
except ZZ and MODE
GND ≤ VI ≤ VDDQ
−5
5
µA
Input Current of MODE
Input = VSS
–30
Input = VDDQ
Input Current of ZZ
µA
5
Input = VSS
Input = VDDQ
IOZ
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
IDD
VDD Operating Supply
Current
VDD = Max., IOUT = 0 mA,
f = fMAX= 1/tCYC
ISB1
Automatic CE
Power-down
Current—TTL Inputs
–5
µA
µA
–5
30
µA
5
µA
7.5-ns cycle, 133 MHz
250
mA
10-ns cycle, 100 MHz
180
mA
VDD = Max, Device Deselected, All speeds
VIN ≥ VIH or VIN ≤ VIL, f = fMAX,
inputs switching
110
mA
ISB2
Automatic CE
VDD = Max, Device Deselected, All speeds
Power-down
VIN ≥ VDD – 0.3V or VIN ≤ 0.3V,
Current—CMOS Inputs f = 0, inputs static
40
mA
ISB3
VDD = Max, Device Deselected, All speeds
Automatic CE
Power-down
VIN ≥ VDDQ – 0.3V or VIN ≤ 0.3V,
Current—CMOS Inputs f = fMAX, inputs switching
100
mA
ISB4
Automatic CE
Power-down
Current—TTL Inputs
40
mA
VDD = Max, Device Deselected, All speeds
VIN ≥ VIH or VIN ≤ VIL, f = 0,
inputs static
Notes:
9. Overshoot: VIH(AC) < VDD +1.5V (Pulse width less than tCYC/2), undershoot: VIL(AC)> –2V (Pulse width less than tCYC/2).
10. TPower-up: Assumes a linear ramp from 0V to VDD (min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
Document #: 38-05688 Rev. *D
Page 8 of 15
CY7C1379C
Capacitance[11]
Parameter
Description
CIN
Input Capacitance
CCLOCK
Clock Input Capacitance
CI/O
I/O Capacitance
Test Conditions
100 TQFP
Max.
165 FBGA
Max.
Unit
5
7
pF
5
7
pF
5
7
pF
100 TQFP
Package
165 FBGA
Package
Unit
29.41
16.8
°C/W
6.13
3.0
°C/W
TA = 25°C, f = 1 MHz,
VDD = 3.3V
VDDQ=3.3V
Thermal Resistance[11]
Parameters
Description
Test Conditions
ΘJA
Thermal Resistance
(Junction to Ambient)
ΘJC
Thermal Resistance
(Junction to Case)
Test conditions follow standard test
methods and procedures for measuring
thermal impedance, per EIA/JESD51
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
VDD
OUTPUT
RL = 50Ω
Z0 = 50Ω
GND
5 pF
VL = 1.5V
(a)
R = 351Ω
INCLUDING
JIG AND
SCOPE
Switching Characteristics Over the Operating
90%
10%
90%
10%
≤ 1 ns
≤ 1 ns
(b)
(c)
Range[12, 13, 14, 15, 16, 17]
–133
Parameter
tPOWER
Description
VDD(Typical) to the First Access[14]
Min.
–100
Max.
Min.
Max.
Unit
1
1
ms
Clock
tCYC
Clock Cycle Time
7.5
10.0
ns
tCH
Clock HIGH
3.0
4.0
ns
tCL
Clock LOW
3.0
4.0
ns
Output Times
tCDV
Data Output Valid after CLK Rise
tDOH
Data Output Hold after CLK Rise
tCLZ
Clock to Low-Z[15, 16, 17]
tCHZ
Clock to
High-Z[15, 16, 17]
tOEV
OE LOW to Output Valid
tOELZ
OE LOW to Output Low-Z[15, 16, 17]
tOEHZ
OE HIGH to Output
High-Z[15, 16, 17]
6.5
7.5
ns
2.0
2.0
ns
0
0
ns
3.5
3.5
0
3.5
ns
3.5
ns
0
3.5
ns
3.5
ns
Notes:
11. Tested initially and after any design or process changes that may affect these parameters.
12. Timing reference level is 1.5V when VDDQ=3.3V.
13. Test conditions shown in (a) of AC Test Loads, unless otherwise noted.
14. This part has a voltage regulator internally; tPOWER is the time that the power needs to be supplied above VDD (minimum) initially, before a read or write operation
can be initiated.
15. tCHZ, tCLZ,tOELZ, and tOEHZ are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
16. At any given voltage and temperature, tOEHZ is less than tOELZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
17. This parameter is sampled and not 100% tested.
Document #: 38-05688 Rev. *D
Page 9 of 15
CY7C1379C
Switching Characteristics Over the Operating Range[12, 13, 14, 15, 16, 17] (continued)
–133
Parameter
Description
Min.
Max.
–100
Min.
Max.
Unit
Set-up Times
tAS
Address Set-up before CLK Rise
1.5
1.5
ns
tALS
ADV/LD Set-up before CLK Rise
1.5
1.5
ns
tWES
WE, BW[A:D] Set-up before CLK Rise
1.5
1.5
ns
tCENS
CEN Set-up before CLK Rise
1.5
1.5
ns
tDS
Data Input Set-up before CLK Rise
1.5
1.5
ns
tCES
Chip Enable Set-up before CLK Rise
1.5
1.5
ns
tAH
Address Hold after CLK Rise
0.5
0.5
ns
tALH
ADV/LD Hold after CLK Rise
0.5
0.5
ns
tWEH
WE, BWX Hold after CLK Rise
0.5
0.5
ns
tCENH
CEN Hold after CLK Rise
0.5
0.5
ns
tDH
Data Input Hold after CLK Rise
0.5
0.5
ns
tCEH
Chip Enable Hold after CLK Rise
0.5
0.5
ns
Hold Times
Document #: 38-05688 Rev. *D
Page 10 of 15
CY7C1379C
Switching Waveforms
Read/Write Waveforms[18, 19, 20]
1
2
3
tCYC
4
5
6
7
8
9
A5
A6
A7
10
CLK
tCENS
tCENH
tCES
tCEH
tCH
tCL
CEN
CE
ADV/LD
WE
BW[A:D]
A1
ADDRESS
tAS
A2
A4
A3
tCDV
tAH
tDOH
tCLZ
DQ
D(A1)
tDS
D(A2)
Q(A3)
D(A2+1)
tOEV
Q(A4+1)
Q(A4)
tOELZ
WRITE
D(A1)
WRITE
D(A2)
D(A5)
Q(A6)
D(A7)
WRITE
D(A7)
DESELECT
tOEHZ
tDH
OE
COMMAND
tCHZ
BURST
WRITE
D(A2+1)
READ
Q(A3)
READ
Q(A4)
DON’T CARE
BURST
READ
Q(A4+1)
tDOH
WRITE
D(A5)
READ
Q(A6)
UNDEFINED
Notes:
18. For this waveform ZZ is tied LOW.
19. When CE is LOW, CE1 is LOW, CE2 is HIGH and CE3 is LOW. When CE is HIGH, CE1 is HIGH or CE2 is LOW or CE3 is HIGH.
20. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document #: 38-05688 Rev. *D
Page 11 of 15
CY7C1379C
Switching Waveforms (continued)
NOP, STALL and Deselect Cycles[18, 19, 21]
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW[A:D]
ADDRESS
A5
tCHZ
D(A1)
DQ
Q(A2)
Q(A3)
D(A4)
Q(A5)
tDOH
COMMAND
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
DON’T CARE
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
ZZ Mode Timing[22, 23]
CLK
t ZZ
ZZ
I
t ZZREC
t ZZI
SUPPLY
I DDZZ
t RZZI
ALL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes:
21. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
22. Device must be deselected when entering ZZ mode. See truth table for all possible signal conditions to deselect the device.
23. I/Os are in High-Z when exiting ZZ sleep mode.
Document #: 38-05688 Rev. *D
Page 12 of 15
CY7C1379C
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
133
Package
Diagram
Ordering Code
CY7C1355C-133AXC
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1355C-133BZC
51-85122 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm)
CY7C1355C-133BZXC
Commercial
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) Lead-Free
CY7C1355C-133AXI
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1355C-133BZI
51-85122 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm)
CY7C1355C-133BZXI
100
Operating
Range
Part and Package Type
lndustrial
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) Lead-Free
CY7C1355C-100AXC
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1355C-100BZC
51-85122 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm)
CY7C1355C-100BZXC
Commercial
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) Lead-Free
CY7C1355C-100AXI
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1355C-100BZI
51-85122 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm)
CY7C1355C-100BZXI
lndustrial
165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.2 mm) Lead-Free
Package Diagrams
100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) (51-85050)
16.00±0.20
1.40±0.05
14.00±0.10
81
100
80
1
20.00±0.10
22.00±0.20
0.30±0.08
0.65
TYP.
30
12°±1°
(8X)
SEE DETAIL
A
51
31
50
0.20 MAX.
R 0.08 MIN.
0.20 MAX.
0.10
1.60 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
0.25
NOTE:
1. JEDEC STD REF MS-026
GAUGE PLANE
0°-7°
R 0.08 MIN.
0.20 MAX.
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0.60±0.15
0.20 MIN.
51-85050-*B
1.00 REF.
DETAIL
Document #: 38-05688 Rev. *D
A
Page 13 of 15
CY7C1379C
Package Diagrams (continued)
165-ball FBGA (13 x 15 x 1.2 mm) (51-85122)
51-85122-*C
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device
Technology, Inc. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05688 Rev. *D
Page 14 of 15
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1379C
Document History Page
Document Title: CY7C1379C 9-Mbit (256K x 32) Flow-through SRAM with NoBL™ Architecture
Document Number: 38-05688
REV.
ECN NO.
Issue Date
Orig. of
Change
Description of Change
**
286269
See ECN
PCI
New data sheet
*A
320834
See ECN
PCI
Address expansion pins/balls in the pinouts for all packages are modified as
per JEDEC standard
Added 133 MHz in the Ordering Information table
Changed ΘJA and ΘJC for TQFP Package from 25 and 9 °C/W to 29.41 and
6.13 °C/W respectively
Changed ΘJA and ΘJC for FBGA Package from 27 and 6 °C/W to 16.8 and
3.0 °C/W respectively
Modified VOL, VOH test conditions
Corrected IDD, tCDV, tCH, tDOH and tCL for 100MHz to 180 mA, 7.5 ns, 4
ns, 2 ns and 4 ns respectively
Changed Snooze to Sleep in the ZZ Mode Electrical Characteristics and truth
table
Added Industrial operating range
Added BZC package in the Ordering Information table
Updated Ordering Information Table
*B
377095
See ECN
PCI
Changed ISB2 from 30 to 40 mA
Modified test condition in note# 10 from VDDQ < VDD to VDDQ < VDD
*C
408725
See ECN
RXU
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed three-state to tri-state
Converted from preliminary to final
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in
the Electrical Characteristics Table
Replaced Package Name column with Package Diagram in the Ordering
Information table
*D
501828
See ECN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND
Updated the Ordering Information table.
Document #: 38-05688 Rev. *D
Page 15 of 15