1CY7C1380BV25 CY7C1380BV25 CY7C1382BV25 PRELIMINARY 512K x 36 / 1 Mb x 18 Pipelined SRAM Features • • • • • • • • • • • Fast clock speed: 200,166, 150, 133 MHz Provide high-performance 3-1-1-1 access rate Fast OE access times: 3.0,3.2, 3.4, 3.8, 4.2 ns Optimal for depth expansion 2.5V (±5%) Operation Common data inputs and data outputs Byte Write Enable and Global Write control Chip enable for address pipeline Address, data, and control registers Internally self-timed WRITE CYCLE Burst control pins (interleaved or linear burst sequence) • Automatic power-down for portable applications • High-density, high-speed packages • JTAG boundary scan for BGA packaging version Functional Description The Cypress Synchronous Burst SRAM family employs high-speed, low-power CMOS designs using advanced single-layer polysilicon, triple-layer metal technology. Each memory cell consists of six transistors. The CY7C1382BV25 and CY7C1380BV25 SRAMs integrate 1,048,576x18 and 524,288x36 SRAM cells with advanced synchronous peripheral circuitry and a 2-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive-edge-triggered clock input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining Chip Enable (CE), burst control inputs (ADSC, ADSP, and ADV), Write Enables (BWa, BWb, BWc, BWd and BWE), and global write (GW). Asynchronous inputs include the output enable (OE) and Burst Mode Control (MODE). The data (DQa,b,c,d) and the data parity (DQPa,b,c,d) outputs, enabled by OE, are also asynchronous. DQa,b,c,d and DQPa,b,c,d apply to CY7C1380BV25 and DQa,b and DQPa,b apply to CY7C1382BV25. a, b, c, d each are of 8 bits wide in the case of DQ and 1 bit wide in the case of DP. Addresses and chip enables are registered with either Address Status Processor (ADSP) or Address Status Controller (ADSC) input pins. Subsequent burst addresses can be internally generated as controlled by the Burst Advance Pin (ADV). Address, data inputs, and write controls are registered on-chip to initiate self-timed WRITE cycle. WRITE cycles can be one to four bytes wide as controlled by the write control inputs. Individual byte write allows individual byte to be written. BWa controls DQa and DQPa. BWb controls DQb and DQPb. BWc controls DQc and DQPd. BWd controls DQd-DQd and DQPd. BWa, BWb BWc, and BWd can be active only with BWE being LOW. GW being LOW causes all bytes to be written. WRITE pass-through capability allows written data available at the output for the immediately next READ cycle. This device also incorporates pipelined enable circuit for easy depth expansion without penalizing system performance. All inputs and outputs of the CY7C1380BV25 and the CY7C1382BV25 are JEDEC standard JESD8-5 compatible. Selection Guide 200 MHz 166 MHz 150 MHz 133 MHz 3.0 3.4 3.8 4.2 280 230 190 160 30 30 30 30 San Jose • Maximum Access Time (ns) Maximum Operating Current (mA) Commercial Maximum CMOS Standby Current (mA) Shaded areas contain advance information. Cypress Semiconductor Corporation • 3901 North First Street • CA 95134 • 408-943-2600 July 5, 2001 CY7C1380BV25 CY7C1382BV25 PRELIMINARY CY7C1380AV25 - 512K x 36 MODE (A[1;0]) 2 BURST Q0 CE COUNTER Q1 CLR CLK ADV ADSC ADSP Q A[18:0] 19 GW 17 DQd, DPd BYTEWRITE REGISTERS DQc, DPc BYTEWRITE REGISTERS Q D DQb, DPb BYTEWRITE REGISTERS Q D DQa, DPa BYTEWRITE REGISTERS Q D BWE BW d D BWc BWb BWa CE1 CE2 CE3 17 ADDRESS CE REGISTER D D 19 512KX36 MEMORY ARRAY Q 36 36 Q ENABLE CE REGISTER D ENABLE DELAY Q REGISTER OUTPUT REGISTERS CLK INPUT REGISTERS CLK OE SLEEP CONTROL ZZ DQa,b,c,d DPa,b CY7C1382AV25 - 1M X 18 MODE (A[1;0]) 2 BURST Q0 CE COUNTER Q1 CLR CLK ADV ADSC ADSP A[19:0] GW BWE BW b Q 19 17 DQb, DPb BYTEWRITE REGISTERS DQa, DPa BYTEWRITE REGISTERS Q D ENABLE CE CE REGISTER Q D D BWa CE1 CE2 CE3 17 ADDRESS CE REGISTER D 19 1 Mb X 18 MEMORY ARRAY Q 18 D ENABLE DELAY Q REGISTER OUTPUT REGISTERS CLK 18 INPUT REGISTERS CLK OE ZZ SLEEP CONTROL DQa,b DPa,b 2 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Pin Configurations NC,DQPb DQb DQb VDDQ VSSQ DQb DQb DQb DQb VSSQ VDDQ DQb DQb VSS NC VDD ZZ DQa DQa VDDQ VSSQ DQa DQa DQa DQa VSSQ VDDQ DQa DQa NC,DQPa NC NC NC CY7C1382BV25 (1 Mb x 18) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 MODE A A A A A1 A0 NC NC VSS VDD 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 VDDQ VSSQ NC NC DQb DQb VSSQ VDDQ DQb DQb NC VDD NC VSS DQb DQb VDDQ VSSQ DQb DQb DPb NC VSSQ VDDQ NC NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3 A A A A A A A A A CY7C1380BV25 (512K X 36) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 MODE A A A A A1 A0 NC NC VSS VDD A A A A A A A A A NC,DQPc DQc DQc VDDQ VSSQ DQc DQc DQc DQc VSSQ VDDQ DQc DQc NC VDD NC VSS DQd DQd VDDQ VSSQ DQd DQd DQd DQd VSSQ VDDQ DQd DQd NC,DQPd 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 A A CE1 CE2 BWd BWc BWb BWa CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A A A CE1 CE2 NC NC BWb BWa CE3 VDD VSS CLK GW BWE OE ADSC ADSP ADV A A 100-Pin TQFP Top View A NC NC VDDQ VSSQ NC DPa DQa DQa VSSQ VDDQ DQa DQa VSS NC VDD ZZ DQa DQa VDDQ VSSQ DQa DQa NC NC VSSQ VDDQ NC NC NC CY7C1380BV25 CY7C1382BV25 PRELIMINARY Pin Configurations (continued) CY7C1380BV25 (512K x 36) 1 2 3 4 5 6 7 A VDDQ A ADSP ADSC A A A A VDDQ C NC NC A A A B A D E DQc DQc A DQPc DQc VDD VSS VSS NC A VSS A DQPb CE1 VSS F VDDQ DQc VSS G H J DQc DQc K DQd BWc VSS NC VSS VSS BWb VSS VDDQ L M DQd DQc DQc VDD DQd DQd OE ADV GW VDD DQb DQb VDDQ N DQd DQd DQd NC VSS NC NC DQb DQb DQb VDD VDDQ DQb DQb VDDQ DQa DQa DQb BWd VSS CLK NC BWa DQa DQa BWE VSS DQa VSS A1 VSS DQa VDDQ DQa A0 VDD VSS DQPa DQa NC A A A NC NC ZZ TCK TDO NC VDDQ P DQd DQPd VSS R NC T NC A NC MODE A U VDDQ TMS TDI CY7C1382BV25 (1 Mb x 18) 1 2 3 A VDDQ B NC NC A A C D 4 5 6 7 A ADSP ADSC VDD A A A A VDDQ A A VSS VSS NC A VSS CE1 VSS VSS VSS VSS A DQPa NC DQa NC NC E NC A NC DQb F VDDQ NC VSS G H J NC DQb VDDQ BWb VSS NC K NC L M DQb DQb NC VDD DQb NC OE ADV GW VDD VSS VSS CLK NC BWa VDDQ VSS VSS VSS NC DQb DQb NC BWE N A1 VSS DQa VDDQ NC P NC DQPb VSS VSS NC DQa R NC NC MODE A NC NC A A T A A A0 VDD A NC ZZ U VDDQ TMS TDI TCK TDO NC VDDQ DQb 4 NC VSS NC DQa DQa VDD VDDQ DQa NC VDDQ NC DQa DQa NC NC CY7C1380BV25 CY7C1382BV25 PRELIMINARY Pin Definitions Name I/O Description A0 A1 A InputSynchronous Address Inputs used to select one of the address locations. Sampled at the rising edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled active. A[1:0] feed the 2-bit counter. BWa BWb BWc BWd InputSynchronous Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM. Sampled on the rising edge of CLK. GW InputSynchronous Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global write is conducted (ALL bytes are written, regardless of the values on BWa,b,c,d and BWE). BWE InputSynchronous Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be asserted LOW to conduct a byte write. CLK Input-Clock Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the burst counter when ADV is asserted LOW, during a burst operation. CE1 InputSynchronous Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is HIGH. CE2 InputSynchronous Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE3 to select/deselect the device. (TQFP Only) CE3 InputSynchronous Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with CE1 and CE2 to select/deselect the device. (TQFP Only) OE InputAsynchronous Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are three-stated, and act as input data pins. OE is masked during the first clock of a read cycle when emerging from a deselected state. ADV InputSynchronous Advance Input signal, sampled on the rising edge of CLK. When asserted, it automatically increments the address in a burst cycle. ADSP InputSynchronous Address Strobe from Processor, sampled on the rising edge of CLK. When asserted LOW, A is captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH. ADSC InputSynchronous Address Strobe from Controller, sampled on the rising edge of CLK. When asserted LOW, A[x:0] is captured in the address registers. A[1:0] are also loaded into the burst counter. When ADSP and ADSC are both asserted, only ADSP is recognized. MODE InputStatic Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDDQ or left floating selects interleaved burst sequence. This is a strap pin and should remain static during device operation. ZZ InputAsynchronous ZZ “sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition with data integrity preserved. DQa, DQPa DQb, DQPb DQc, DQPc DQd, DQPd I/OSynchronous Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered by the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified by A during the previous clock rise of the read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH, DQx and DPx are placed in a three-state condition. TDO JTAG serial output Synchronous Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK (BGA Only). TDI JTAG serial input Synchronous Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK (BGA Only). 5 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Pin Definitions Name I/O Description TMS Test Mode Select Synchronous This pin controls the Test Access Port state machine. Sampled on the rising edge of TCK (BGA Only). TCK JTAG serial clock Serial clock to the JTAG circuit (BGA Only). VDD Power Supply VSS Ground Ground for the core of the device. Should be connected to ground of the system. VDDQ I/O Power Supply Power supply for the I/O circuitry. Should be connected to a 3.3V –5% +10% power supply. VSSQ I/O Ground Ground for the I/O circuitry. Should be connected to ground of the system. NC - Power supply inputs to the core of the device. Should be connected to 3.3V –5% +10% power supply. No Connects. 6 PRELIMINARY Introduction CY7C1380BV25 CY7C1382BV25 ed into the address register and the address advancement logic while being delivered to the RAM core. The write signals (GW, BWE, and BWx) and ADV inputs are ignored during this first cycle. Functional Overview All synchronous inputs pass through input registers controlled by the rising edge of the clock. All data outputs pass through output registers controlled by the rising edge of the clock. Maximum access delay from the clock rise (tCO) is 3.8 ns (133-MHz device). ADSP triggered write accesses require two clock cycles to complete. If GW is asserted LOW on the second clock rise, the data presented to the DQx inputs is written into the corresponding address location in the RAM core. If GW is HIGH, then the write operation is controlled by BWE and BWx signals. The CY7C1380BV25/CY7C1382BV25 provides byte write capability that is described in the write cycle description table. Asserting the Byte Write Enable input (BWE) with the selected Byte Write (BWa,b,c,d for CY7C1380BV25 & BWa,b for CY7C1382BV25) input will selectively write to only the desired bytes. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. The CY7C1380BV25/CY7C1382BV25 supports secondary cache in systems utilizing either a linear or interleaved burst sequence. The interleaved burst order supports Pentium and i486 processors. The linear burst sequence is suited for processors that utilize a linear burst sequence. The burst order is user selectable, and is determined by sampling the MODE input. Accesses can be initiated with either the Processor Address Strobe (ADSP) or the Controller Address Strobe (ADSC). Address advancement through the burst sequence is controlled by the ADV input. A two-bit on-chip wraparound burst counter captures the first address in a burst sequence and automatically increments the address for the rest of the burst access. Because the CY7C1380BV25/CY7C1382BV25 is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQ inputs. Doing so will three-state the output drivers. As a safety precaution, DQ are automatically three-stated whenever a write cycle is detected, regardless of the state of OE. Byte write operations are qualified with the Byte Write Enable (BWE) and Byte Write Select (BWa,b,c,d for 1380V25 and BWa,b for 1382V25) inputs. A Global Write Enable (GW) overrides all byte write inputs and writes data to all four bytes. All writes are simplified with on-chip synchronous self-timed write circuitry. Single Write Accesses Initiated by ADSC ADSC write accesses are initiated when the following conditions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted HIGH, (3) chip select is asserted active, and (4) the appropriate combination of the write inputs (GW, BWE, and BWx) are asserted active to conduct a write to the desired byte(s). ADSC triggered write accesses require a single clock cycle to complete. The address presented to A[17:0] is loaded into the address register and the address advancement logic while being delivered to the RAM core. The ADV input is ignored during this cycle. If a global write is conducted, the data presented to the DQ[x:0] is written into the corresponding address location in the RAM core. If a byte write is conducted, only the selected bytes are written. Bytes not selected during a byte write operation will remain unaltered. A synchronous self-timed write mechanism has been provided to simplify the write operations. Synchronous Chip Selects (CE1, CE2, CE3 for TQFP / CE1 for BGA) and an asynchronous Output Enable (OE) provide for easy bank selection and output three-state control. ADSP is ignored if CE1 is HIGH. Single Read Accesses This access is initiated when the following conditions are satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2) chip selects are all asserted active, and (3) the write signals (GW, BWE) are all deasserted HIGH. ADSP is ignored if CE1 is HIGH. The address presented to the address inputs is stored into the address advancement logic and the Address Register while being presented to the memory core. The corresponding data is allowed to propagate to the input of the Output Registers. At the rising edge of the next clock the data is allowed to propagate through the output register and onto the data bus within 3.0 ns (200-MHz device) if OE is active LOW. The only exception occurs when the SRAM is emerging from a deselected state to a selected state, its outputs are always three-stated during the first cycle of the access. After the first cycle of the access, the outputs are controlled by the OE signal. Consecutive single read cycles are supported. Once the SRAM is deselected at clock rise by the chip select and either ADSP or ADSC signals, its output will three-state immediately. Because the CY7C1380BV25/CY7C1382BV25 is a common I/O device, the Output Enable (OE) must be deasserted HIGH before presenting data to the DQ[x:0] inputs. Doing so will three-state the output drivers. As a safety precaution, DQ[x:0] are automatically three-stated whenever a write cycle is detected, regardless of the state of OE. Burst Sequences The CY7C1380BV25/CY7C1382BV25 provides a two-bit wraparound counter, fed by A[1:0], that implements either an interleaved or linear burst sequence. The interleaved burst sequence is designed specifically to support Intel® Pentium® applications. The linear burst sequence is designed to support processors that follow a linear burst sequence. The burst sequence is user selectable through the MODE input. Single Write Accesses Initiated by ADSP This access is initiated when both of the following conditions are satisfied at clock rise: (1) ADSP is asserted LOW, and (2) chip select is asserted active. The address presented is load- 7 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Asserting ADV LOW at clock rise will automatically increment the burst counter to the next address in the burst sequence. Both read and write burst operations are supported. Linear Burst Sequence First Address Interleaved Burst Sequence First Address Second Address Third Address Fourth Address Second Address Third Address Fourth Address A[1:0] A[1:0] A[1:0] A[1:0] 00 01 10 11 01 10 11 00 10 11 00 01 11 00 01 10 A[1:0]] A[1:0] A[1:0] A[1:0] 00 01 10 11 01 00 11 10 10 11 00 01 Sleep Mode 11 10 01 00 The ZZ input pin is an asynchronous input. Asserting ZZ places the SRAM in a power conservation “sleep” mode. Two clock cycles are required to enter into or exit from this “sleep” mode. While in this mode, data integrity is guaranteed. Accesses pending when entering the “sleep” mode are not considered valid nor is the completion of the operation guaranteed. The device must be deselected prior to entering the “sleep” mode. CEs, ADSP, and ADSC must remain inactive for the duration of tZZREC after the ZZ input returns LOW. ZZ Mode Electrical Characteristics Parameter IDDZZ tZZS tZZREC Description Test Conditions Snooze mode standby current Min. Max. Unit ZZ > VDD − 0.2V 15 mA Device operation to ZZ ZZ > VDD − 0.2V 2tCYC ns ZZ recovery time ZZ < 0.2V 2tCYC 8 ns CY7C1380BV25 CY7C1382BV25 PRELIMINARY Cycle Descriptions[1, 2, 3, 4] Next Cycle Add. Used ZZ CE3 CE2 CE1 ADSP ADSC ADV OE DQ Write Unselected None L X X 1 X 0 X X Hi-Z X Unselected None L 1 X 0 0 X X X Hi-Z X Unselected None L X 0 0 0 X X X Hi-Z X Unselected None L 1 X 0 1 0 X X Hi-Z X Unselected None L X 0 0 1 0 X X Hi-Z X Begin Read External L 0 1 0 0 X X X Hi-Z X Begin Read External L 0 1 0 1 0 X X Hi-Z Read Continue Read Next L X X X 1 1 0 1 Hi-Z Read Continue Read Next L X X X 1 1 0 0 DQ Read Continue Read Next L X X 1 X 1 0 1 Hi-Z Read Continue Read Next L X X 1 X 1 0 0 DQ Read Suspend Read Current L X X X 1 1 1 1 Hi-Z Read Suspend Read Current L X X X 1 1 1 0 DQ Read Suspend Read Current L X X 1 X 1 1 1 Hi-Z Read Suspend Read Current L X X 1 X 1 1 0 DQ Read Begin Write Current L X X X 1 1 1 X Hi-Z Write Begin Write Current L X X 1 X 1 1 X Hi-Z Write Begin Write External L 0 1 0 1 0 X X Hi-Z Write Continue Write Next L X X X 1 1 0 X Hi-Z Write Continue Write Next L X X 1 X 1 0 X Hi-Z Write Suspend Write Current L X X X 1 1 1 X Hi-Z Write Suspend Write Current L X X 1 X 1 1 X Hi-Z Write ZZ “sleep” None H X X X X X X X Hi-Z X Note: 1. X = “Don't Care,” 1 = HIGH, 0 = LOW. 2. Write is defined by BWE, BWx, and GW. See Write Cycle Descriptions table. 3. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock. 4. CE1, CE2 and CE3 are available only in the TQFP package. BGA package has a single chip select CE1. 9 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Write Cycle Descriptions[5, 6, 7] Function (1380AV25) GW BWE BWd BWc BWb BWa Read 1 1 X X X X Read 1 0 1 1 1 1 Write Byte 0 - DQa 1 0 1 1 1 0 Write Byte 1 - DQb 1 0 1 1 0 1 Write Bytes 1, 0 1 0 1 1 0 0 Write Byte 2 - DQc 1 0 1 0 1 1 Write Bytes 2, 0 1 0 1 0 1 0 Write Bytes 2, 1 1 0 1 0 0 1 Write Bytes 2, 1, 0 1 0 1 0 0 0 Write Byte 3 - DQd 1 0 0 1 1 1 Write Bytes 3, 0 1 0 0 1 1 0 Write Bytes 3, 1 1 0 0 1 0 1 Write Bytes 3, 1, 0 1 0 0 1 0 0 Write Bytes 3, 2 1 0 0 0 1 1 Write Bytes 3, 2, 0 1 0 0 0 1 0 Write Bytes 3, 2, 1 1 0 0 0 0 1 Write All Bytes 1 0 0 0 0 0 Write All Bytes 0 X X X X X Function (1382AV25) GW BWE BWb BWa Read 1 1 X X Read 1 0 1 1 Write Byte 0 - DQ[7:0] and DP0 1 0 1 0 Write Byte 1 - DQ[15:8] and DP1 1 0 0 1 Write All Bytes 1 0 0 0 Write All Bytes 0 X X X 10 PRELIMINARY IEEE 1149.1 Serial Boundary Scan (JTAG) CY7C1380BV25 CY7C1382BV25 ry. Only one register can be selected at a time through the instruction registers. Data is serially loaded into the TDI pin on the rising edge of TCK. Data is output on the TDO pin on the falling edge of TCK. The CY7C1380BV25/CY7C1382BV25 incorporates a serial boundary scan Test Access Port (TAP) in the FBGA package only. The TQFP package does not offer this functionality. This port operates in accordance with IEEE Standard 1149.1-1900, but does not have the set of functions required for full 1149.1 compliance. These functions from the IEEE specification are excluded because their inclusion places an added delay in the critical speed path of the SRAM. Note that the TAP controller functions in a manner that does not conflict with the operation of other devices using 1149.1 fully compliant TAPs. The TAP operates using JEDEC standard 2.5V I/O logic levels. Instruction Register Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO pins as shown in the TAP Controller Block Diagram. Upon power-up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state as described in the previous section. When the TAP controller is in the CaptureIR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board level serial test path. Disabling the JTAG Feature It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are internally pulled up and may be unconnected. They may alternately be connected to VDD through a pull-up resistor. TDO should be left unconnected. Upon power-up, the device will come up in a reset state which will not interfere with the operation of the device. Bypass Register To save time when serially shifting data through registers, it is sometimes advantageous to skip certain states. The bypass register is a single-bit register that can be placed between TDI and TDO pins. This allows data to be shifted through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed. Test Access Port (TAP) - Test Clock The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK. Boundary Scan Register The boundary scan register is connected to all the input and output pins on the SRAM. Several no connect (NC) pins are also included in the scan register to reserve pins for higher density devices. The x36 configuration has a xx-bit-long register, and the x18 configuration has a yy-bit-long register. Test Mode Select The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. It is allowable to leave this pin unconnected if the TAP is not used. The pin is pulled up internally, resulting in a logic HIGH level. The boundary scan register is loaded with the contents of the RAM Input and Output ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO pins when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instructions can be used to capture the contents of the Input and Output ring. Test Data-In (TDI) The TDI pin is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see the TAP Controller State Diagram. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the Most Significant Bit (MSB) on any register. The Boundary Scan Order tables show the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO. Identification (ID) Register Test Data Out (TDO) The TDO output pin is used to serially clock data-out from the registers. The e output is active depending upon the current state of the TAP state machine (see TAP Controller State Diagram). The output changes on the falling edge of TCK. TDO is connected to the Least Significant Bit (LSB) of any register. The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in the Identification Register Definitions table. Performing a TAP Reset TAP Instruction Set A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This RESET does not affect the operation of the SRAM and may be performed while the SRAM is operating. At power-up, the TAP is reset internally to ensure that TDO comes up in a high-Z state. Eight different instructions are possible with the three-bit instruction register. All combinations are listed in the Instruction Code table. Three of these instructions are listed as RESERVED and should not be used. The other five instructions are described in detail below. TAP Registers The TAP controller used in this SRAM is not fully compliant to the 1149.1 convention because some of the mandatory 1149.1 instructions are not fully implemented. The TAP controller cannot be used to load address, data or control signals into the Registers are connected between the TDI and TDO pins and allow data to be scanned into and out of the SRAM test circuit- 11 PRELIMINARY SRAM and cannot preload the Input or Output buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of SAMPLE / PRELOAD; rather it performs a capture of the Inputs and Output ring when these instructions are executed. CY7C1380BV25 CY7C1382BV25 When the SAMPLE / PRELOAD instructions loaded into the instruction register and the TAP controller in the Capture-DR state, a snapshot of data on the inputs and output pins is captured in the boundary scan register. The user must be aware that the TAP controller clock can only operate at a frequency up to 10 MHz, while the SRAM clock operates more than an order of magnitude faster. Because there is a large difference in the clock frequencies, it is possible that during the Capture-DR state, an input or output will undergo a transition. The TAP may then try to capture a signal while in transition (metastable state). This will not harm the device, but there is no guarantee as to the value that will be captured. Repeatable results may not be possible. Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO pins. To execute the instruction once it is shifted in, the TAP controller needs to be moved into the Update-IR state. EXTEST EXTEST is a mandatory 1149.1 instruction which is to be executed whenever the instruction register is loaded with all 0s. EXTEST is not implemented in the TAP controller, and therefore this device is not compliant to the 1149.1 standard. To guarantee that the boundary scan register will capture the correct value of a signal, the SRAM signal must be stabilized long enough to meet the TAP controller's capture set-up plus hold times (tCS and tCH). The SRAM clock input might not be captured correctly if there is no way in a design to stop (or slow) the clock during a SAMPLE / PRELOAD instruction. If this is an issue, it is still possible to capture all other signals and simply ignore the value of the CK and CK captured in the boundary scan register. The TAP controller does recognize an all-0 instruction. When an EXTEST instruction is loaded into the instruction register, the SRAM responds as if a SAMPLE / PRELOAD instruction has been loaded. There is one difference between the two instructions. Unlike the SAMPLE / PRELOAD instruction, EXTEST places the SRAM outputs in a High-Z state. Once the data is captured, it is possible to shift out the data by putting the TAP into the Shift-DR state. This places the boundary scan register between the TDI and TDO pins. IDCODE The IDCODE instruction causes a vendor-specific, 32-bit code to be loaded into the instruction register. It also places the instruction register between the TDI and TDO pins and allows the IDCODE to be shifted out of the device when the TAP controller enters the Shift-DR state. The IDCODE instruction is loaded into the instruction register upon power-up or whenever the TAP controller is given a test logic reset state. Note that since the PRELOAD part of the command is not implemented, putting the TAP into the Update to the Update-DR state while performing a SAMPLE / PRELOAD instruction will have the same effect as the Pause-DR command. Bypass When the BYPASS instruction is loaded in the instruction register and the TAP is placed in a Shift-DR state, the bypass register is placed between the TDI and TDO pins. The advantage of the BYPASS instruction is that it shortens the boundary scan path when multiple devices are connected together on a board. SAMPLE Z The SAMPLE Z instruction causes the boundary scan register to be connected between the TDI and TDO pins when the TAP controller is in a Shift-DR state. It also places all SRAM outputs into a High-Z state. Reserved SAMPLE / PRELOAD These instructions are not implemented but are reserved for future use. Do not use these instructions. SAMPLE / PRELOAD is a 1149.1 mandatory instruction. The PRELOAD portion of this instruction is not implemented, so the TAP controller is not fully 1149.1 compliant. 12 CY7C1380BV25 CY7C1382BV25 PRELIMINARY TAP Controller State Diagram 1 TEST-LOGIC RESET 0 TEST-LOGIC/ IDLE 1 1 1 SELECT DR-SCAN SELECT IR-SCAN 0 0 1 1 CAPTURE-DR CAPTURE-DR 0 0 0 SHIFT-DR 0 SHIFT-IR 1 1 1 EXIT1-DR 1 EXIT1-IR 0 0 PAUSE-DR 0 0 PAUSE-IR 1 1 0 0 EXIT2-DR EXIT2-IR 1 1 UPDATE-DR 1 0 Note: The 0/1 next to each state represents the value at TMS at the rising edge of TCK. 13 UPDATE-IR 1 0 CY7C1380BV25 CY7C1382BV25 PRELIMINARY TAP Controller Block Diagram 0 Bypass Register Selection Circuitry 2 TDI 1 0 1 0 1 0 Selection Circuitry TDO Instruction Register 31 30 29 . . 2 Identification Register x . . . . 2 Boundary Scan Register TCK TAP Controller TMS TAP Electrical Characteristics Over the Operating Range[5, 6] Parameter Description Test Conditions Min. Max. Unit VOH1 Output HIGH Voltage IOH = –2.0 mA 1.7 V VOH2 Output HIGH Voltage IOH = –100 mA 2.1 V VOL1 Output LOW Voltage IOL = 2.0 mA 0.7 V VOL2 Output LOW Voltage IOL = 100 mA 0.2 V VIH Input HIGH Voltage 1.7 VDD+0.3 V VIL Input LOW Voltage –0.3 0.7 V IX Input Load Current –5 5 mA GND < VI < VDDQ Notes: 5. All Voltage referenced to Ground. 6. Overshoot: VIH(AC)<VDD+1.5V for t<tTCYC/2. Undershoot:VIL(AC)<0.5V for t<tTCYC/2. Power-up: VIH<2.6V and VDD<2.4V and VDDQ<1.4V for t<200 ms. 14 PRELIMINARY CY7C1380BV25 CY7C1382BV25 TAP AC Switching Characteristics Over the Operating Range[7, 8] Parameters Description Min. Max. Unit 10 MHz tTCYC TCK Clock Cycle Time tTF TCK Clock Frequency 100 ns tTH TCK Clock HIGH 40 ns tTL TCK Clock LOW 40 ns tTMSS TMS Set-up to TCK Clock Rise 10 ns tTDIS TDI Set-up to TCK Clock Rise 10 ns tCS Capture Set-up to TCK Rise 10 ns tTMSH TMS Hold after TCK Clock Rise 10 ns tTDIH TDI Hold after Clock Rise 10 ns tCH Capture Hold after Clock Rise 10 ns Set-up Times Hold Times Output Times tTDOV TCK Clock LOW to TDO Valid tTDOX TCK Clock LOW to TDO Invalid 20 0 Notes: 7. tCS and tCH refer to the set-up and hold time requirements of latching data from the boundary scan register. 8. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns. 15 ns ns CY7C1380BV25 CY7C1382BV25 PRELIMINARY TAP Timing and Test Conditions 1.25V 50Ω ALL INPUT PULSES TDO 2.5V Z0 =50Ω 1.25V CL =20 pF 0V GND (a) tTH tTL Test Clock TCK tTCYC tTMSS tTMSH Test Mode Select TMS tTDIS tTDIH Test Data-In TDI Test Data-Out TDO tTDOX 16 tTDOV CY7C1380BV25 CY7C1382BV25 PRELIMINARY Identification Register Definitions Instruction Field 512K x 36 1 Mb x 18 xxxx xxxx Device Depth (27:23) 00111 01000 Defines depth of SRAM. 512K or 1 Mb Device Width (22:18) 00100 00011 Defines with of the SRAM. x36 or x18 Cypress Device ID (17:12) xxxxx xxxxx Reserved for future use. Cypress JEDEC ID (11:1) 00011100100 00011100100 1 1 Revision Number (31:28) ID Register Presence (0) Description Reserved for version number. Allows unique identification of SRAM vendor. Indicate the presence of an ID register. Scan Register Sizes Register Name Bit Size (x18) Bit Size (x36) Instruction 3 3 Bypass 1 1 ID 32 32 Boundary Scan 70 51 Identification Codes Instruction Code Description EXTEST 000 Captures the Input/Output ring contents. Places the boundary scan register between the TDI and TDO. Forces all SRAM outputs to High-Z state. This instruction is not 1149.1 compliant. IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This operation does not affect SRAM operation. SAMPLE Z 010 Captures the Input/Output contents. Places the boundary scan register between TDI and TDO. Forces all SRAM output drivers to a High-Z state. RESERVED 011 Do Not Use: This instruction is reserved for future use. SAMPLE/PRELOAD 100 Captures the Input/Output ring contents. Places the boundary scan register between TDI and TDO. Does not affect the SRAM operation. This instruction does not implement 1149.1 preload function and is therefore not 1149.1 compliant. RESERVED 101 Do Not Use: This instruction is reserved for future use. RESERVED 110 Do Not Use: This instruction is reserved for future use. BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation. 17 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Boundary Scan Order (512K X 18) Bit # Signal Name Bump ID Signal Name Bit # Boundary Scan Order (1 Mb X 18) Bump ID Bit # Signal Name Bump ID Signal Name Bit # Bump ID 1 A 2R 36 A 6B 1 A 2R 36 DQb 2E 2 A 3T 37 BWa 5L 2 A 2T 37 DQb 2G 3 A 4T 38 BWb 5G 3 A 3T 38 DQb 1H 4 A 5T 39 BWc 3G 4 A 5T 39 NC 5R 5 A 6R 40 BWd 3L 5 A 6R 40 DQb 2K 6 A 3B 41 A 2B 6 A 3B 41 DQb 1L 7 A 5B 42 CE 4E 7 A 5B 42 DQb 2M 8 DQa 6P 43 A 3A 8 DQa 7P 43 DQb 1N 9 DQa 7N 44 A 2A 9 DQa 6N 44 DQb 2P 10 DQa 6M 45 DQc 2D 10 DQa 6L 45 MODE 3R 11 DQa 7L 46 DQc 1E 11 DQa 7K 46 A 2C 12 DQa 6K 47 DQc 2F 12 ZZ 7T 47 A 3C 13 DQa 7P 48 DQc 1G 13 DQa 6H 48 A 5C 14 DQa 6N 49 DQc 1D 14 DQa 7G 49 A 6C 15 DQa 6L 50 DQc 1D 15 DQa 6F 50 A1 4N 16 DQa 7K 51 DQc 2E 16 DQa 7E 51 A0 4P 17 ZZ 7T 52 DQc 2G 17 DQa 6D 18 DQb 6H 53 DQc 1H 18 A 6T 19 DQb 7G 54 NC 5R 19 A 6A 20 DQb 6F 55 DQd 2K 20 A 5A 21 DQb 7E 56 DQd 1L 21 ADV 4G 22 DQb 6D 57 DQd 2M 22 ADSP 4A 23 DQb 7H 58 DQd 1N 23 ADSC 4B 24 DQb 6G 59 DQd 2P 24 OE 4F 25 DQb 6E 60 DQd 1K 25 BWE 4M 26 DQb 7D 61 DQd 2L 26 GW 4H 27 A 6A 62 DQd 2N 27 CLK 4K 28 A 5A 63 DQd 1P 28 A 6B 29 ADV 4G 64 MODE 3R 29 BWa 5L 30 ADSP 4A 65 A 2C 30 BWb 3G 31 ADSC 4B 66 A 3C 31 A 2B 32 OE 4F 67 A 5C 32 CE 4E 33 BWE 4M 68 A 6C 33 A 3A 34 GW 4H 69 A1 4N 34 A 2A 35 CLK 4K 70 A0 4P 35 DQb 1D 18 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Maximum Ratings Current into Outputs (LOW)......................................... 20 mA Static Discharge Voltage .......................................... >2001V (per MIL-STD-883, Method 3015) Latch-Up Current.................................................... >200 mA (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –55°C to +150°C Ambient Temperature with Power Applied ............................................. –55°C to +125°C Supply Voltage on VDD Relative to GND........ –0.3V to +4.6V DC Voltage Applied to Outputs in High Z State[9] ................................. –0.5V to VDDQ + 0.5V DC Input Voltage[9] .............................. –0.5V to VDDQ + 0.5V Operating Range Range Ambient Temp.[9] VDD VDDQ Com’l 0−70°C 2.5V +10%/–5% 2.375V – VDD Electrical Characteristics Over the Operating Range Parameter Description Test Conditions Min. Max. Unit 3.6 V VDD Power Supply Voltage 3.3V range 3.135 VDDQ I/O Supply Voltage 3.3V range 3.135 3.6 V 2.5V range 2.375 VDD V VOH Output HIGH Voltage VDD = Min., IOH = −1.0 mA 2.5V VOL Output LOW Voltage VDD = Min., IOL = 1.0 mA 2.5V VIH Input HIGH Voltage 2.5V 1.7 VIL Input LOW Voltage[9] 2.5V –0.3 0.7 IX Input Load Current except ZZ and MODE GND ≤ VI ≤ VDDQ −5 5 µA IZZ Input Current of MODE Input = VSS −30 30 µA IOZ Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled IDD VDD Operating Supply VDD = Max., IOUT = 0 mA, f = fMAX = 1/tCYC Automatic CE Power-Down Current—TTL Inputs Max. VDD, Device Deselected, VIN ≥ VIH or VIN ≤ VIL f = fMAX = 1/tCYC 2 µA mA 6.0-ns cycle, 166 MHz 230 mA 6.7-ns cycle, 150 MHz 190 mA 7.5-ns cycle, 133 MHz 160 mA 5.0-ns cycle, 200 MHz 100 mA 6.0-ns cycle, 166 MHz 80 mA 6.7-ns cycle, 150 MHz 50 mA 7.5-ns cycle, 133 MHz 35 mA All speed grades 30 mA Max. VDD, Device Deselected, VIN ≤ 0.3V or VIN > VDDQ – 0.3V, f=0 ISB3 Automatic CE Power-Down Current—CMOS Inputs Max. VDD, Device Deselected, or 5.0-ns cycle, 200 MHz VIN ≤ 0.3V or VIN > VDDQ – 0.3V 6.0-ns cycle, 166 MHz f = fMAX = 1/tCYC 6.7-ns cycle, 150 MHz Max. VDD, Device Deselected, VIN ≥ VIH or VIN ≤ VIL, f = 0 Shaded areas contain advance information. Notes: 9. Minimum voltage equals –2.0V for pulse durations of less than 20 ns TA is the temperature. 19 −2 µA 280 Automatic CE Power-Down Current—CMOS Inputs Automatic CE Power-Down Current—TTL Inputs 0.7 5.0-ns cycle, 200 MHz ISB2 ISB4 V −5 Input Current of ZZ ISB1 1.7 90 mA 70 mA 40 mA 7.5-ns cycle, 133 MHz 25 mA All Speeds 50 mA CY7C1380BV25 CY7C1382BV25 PRELIMINARY Capacitance[10] Parameter Description Test Conditions CIN Input Capacitance CCLK Clock Input Capacitance CI/O Input/Output Capacitance TA = 25°C, f = 1 MHz, VDD = 3.3V, VDDQ = 2.5V Max. Unit 3 pF 3 pF 3 pF AC Test Loads and Waveforms[11] R=1667Ω 2.5V OUTPUT ALL INPUT PULSES OUTPUT Z0 =50Ω RL =50Ω 2.5V 10% 5 pF R=1538Ω R=1538 VTH = 1.25V (a) INCLUDING JIG AND SCOPE (b) Note: 10. Tested initially and after any design or process changes that may affect these parameters. 11. Input waveform should have a slew rate of 1 V/ns. 20 [10] 90% 10% 90% GND ≤ 2.5 ns ≤ 2.5 ns (c) CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Characteristics Over the Operating Range[12, 13, 14] a-166 -200 Parameter Description Min. Max. Min. Max. -150 Min. -133 Max. Min. Max. Unit tCYC Clock Cycle Time 5.0 6.0 6.7 7.5 ns tCH Clock HIGH 1.8 2.1 2.5 3.0 ns tCL Clock LOW 1.8 2.1 2.5 3.0 ns tAS Address Set-Up Before CLK Rise 1.4 1.5 1.5 1.5 ns tAH Address Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tCO Data Output Valid After CLK Rise tDOH Data Output Hold After CLK Rise 1.5 1.5 1.5 1.5 ns tADS ADSP, ADSC Set-Up Before CLK Rise 1.4 2.0 2.0 2.0 ns tADH ADSP, ADSC Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tWES BWE, GW, BWx Set-Up Before CLK Rise 1.4 2.0 2.0 2.0 ns tWEH BWE, GW, BWx Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tADVS ADV Set-Up Before CLK Rise 1.4 2.0 2.0 2.0 ns tADVH ADV Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tDS Data Input Set-Up Before CLK Rise 1.4 2.0 2.0 2.0 ns tDH Data Input Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tCES Chip enable Set-Up 1.4 2.0 2.0 2.0 ns tCEH Chip enable Hold After CLK Rise 0.4 0.5 0.5 0.5 ns tCHZ tCLZ Clock to High-Z[13] Clock to Low-Z[13] 1.5 0 OE HIGH to Output tEOLZ OE LOW to Output Low-Z[13, 14] OE LOW to Output 3.0 3.4 1.5 3.0 0 High-Z[13, 14] tEOHZ tEOV 3.0 3.0 0 3.5 1.5 3.5 0 3.5 0 Valid[13] 3.8 1.5 3.5 0 4.0 0 3.5 4.2 ns ns 4.0 0 4.0 ns ns ns 4.0 ns Shaded areas contain advance information. Notes: 12. Unless otherwise noted, test conditions assume signal transition time of 2.5 ns or less, timing reference levels of 1.25V, input pulse levels of 0 to 2.5V, and output loading of the specified IOL/IOH and load capacitance. Shown in (a), (b) and (c) of AC test loads. 13. tCHZ, tCLZ, tOEV, tEOLZ, and tEOHZ are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage. 14. At any given voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ. a. 21 CY7C1380BV25 CY7C1382BV25 PRELIMINARY 1 Switching Waveforms Write Cycle Timing[4, 15, 16] Single Write Burst Write Pipelined Write tCH Unselected tCYC CLK tADH tADS tCL ADSP ignored with CE1 inactive ADSP tADH tADS ADSC initiated write ADSC tADVH tADVS ADV tAS ADD ADV Must Be Inactive for ADSP Write WD1 WD3 WD2 tAH GW tWS tWH WE tCES tWH tWS tCEH CE1 masks ADSP CE1 tCES tCEH Unselected with CE2 CE2 CE3 tCES tCEH OE tDH tDS Data High-Z In 1a 1a 2a 2c 2b = UNDEFINED 2d 3a = DON’T CARE Notes: 15. WE is the combination of BWE, BWx and GW to define a write cycle (see Write Cycle Descriptions table). 16. WDx stands for Write Data to Address X. 22 High-Z CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Waveforms (continued) Read Cycle Timing[4, 15, 17] Single Read tCYC Burst Read Unselected tCH Pipelined Read CLK tADH tADS tCL ADSP ignored with CE1 inactive ADSP tADS ADSC initiated read ADSC tADVS tADH Suspend Burst ADV tADVH tAS ADD RD1 RD3 RD2 tAH GW tWS tWS tWH WE tCES tCEH tWH CE1 masks ADSP CE1 Unselected with CE2 CE2 tCES tCEH CE3 tCES OE tCEH tEOV tOEHZ tDOH Data Out tCO 1a 1a 2a 2b 2c 2c 2d 3a tCLZ tCHZ = DON’T CARE = UNDEFINED Note: 17. RDx stands for Read Data from Address X. 23 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Waveforms (continued) Read/Write Cycle Timing[4, 15, 16, 17] Single Read tCYC Single Write Unselected Burst Read tCH Pipelined Read CLK tADH tADS tCL ADSP ignored with CE1 inactive ADSP tADS ADSC tADVS tADH ADV tAS ADD tADVH RD1 WD2 RD3 tAH GW tWS tWS tWH WE tCES tCEH tWH CE1 masks ADSP CE1 CE2 tCES tCEH CE3 tCES tCEH tEOV OE Data In/Out tEOHZ tEOLZ tCO 1a 1a Out tDS tDH 2a In 2a Out = DON’T CARE = UNDEFINED 24 3a Out tDOH 3b Out 3c Out 3d Out tCHZ CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Waveforms (continued) Pipeline Timing[4, 18, 19] tCH tCYC tCL CLK tAS ADD RD1 tADS RD2 RD3 WD1 RD4 WD2 WD3 WD4 tADH ADSC initiated Reads ADSC ADSP initiated Reads ADSP ADV tCEH tCES CE1 CE tWEH tWES WE ADSP ignored with CE1 HIGH OE tCLZ Data In/Out 1a Out 2a Out 3a Out 1a In 4a Out 2a In 3a In tCDV tDOH Back to Back Reads tCHZ = UNDEFINED = DON’T CARE Notes: 18. Device originally deselected. 19. CE is the combination of CE2 and CE3. All chip selects need to be active in order to select the device. 25 4a D(C) In CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Waveforms (continued) OE Switching Waveforms OE tEOV tEOHZ I/Os Three-State tEOLZ 26 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Switching Waveforms (continued) ZZ Mode Timing [4, 20, 21] CLK ADSP HIGH ADSC CE1 CE2 LOW HIGH CE3 ZZ IDD tZZS IDD(active) IDDZZ tZZREC I/Os Three-state Note: 20. Device must be deselected when entering ZZ mode. See Cycle Descriptions Table for all possible signal conditions to deselect the device. 21. I/Os are in three-state when exiting ZZ sleep mode. 27 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Ordering Information Speed (MHz) Ordering Code 200 CY7C1380BV25-200AC 166 CY7C1380BV25-166AC 150 CY7C1380BV25-150AC 133 CY7C1380BV25-133AC 200 CY7C1380BV25-200BGC 166 CY7C1380BV25-166BGC 150 CY7C1380BV25-150BGC 133 CY7C1380BV25-133BGC 200 CY7C1382BV25-200AC 166 CY7C1382BV25-166AC 150 CY7C1382BV25-150AC 133 CY7C1382BV25-133AC 200 CY7C1382BV25-200BGC 166 CY7C1382BV25-166BGC 150 CY7C1382BV25-150BGC 133 CY7C1382BV25-133BGC Package Name A101 BG119 A101 BG119 Package Type Operating Range 100-Lead Thin Quad Flat Pack Commercial 119 Ball BGA 100-Lead Thin Quad Flat Pack 119 Ball BGA Shaded areas contain advance information. Document #: 38-01075-*A 28 Commercial PRELIMINARY CY7C1380BV25 CY7C1382BV25 Package Diagrams 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A101 51-85050-A 29 CY7C1380BV25 CY7C1382BV25 PRELIMINARY Package Diagrams (continued) 119-Lead BGA (14 x 22 x 2.4 mm) BG119 51-85115 Revision History Document Title: CY7C1380BV25/CY7C1382BV25 Document Number: 38-01075 REV. ECN NO. ** *A 3771 ISSUE DATE ORIG. OF CHANGE 9/30/2000 MPR 1. New Data Sheet 05/04/01 PKS 1.Changed Vih/Vil values 2. Changed Icc Values 3. Changed Pin Capacitance values DESCRIPTION OF CHANGE © Cypress Semiconductor Corporation, 2001. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.