CYPRESS CY8C20180_09

CY8C20180
CapSense Express™ - 8 Configurable IOs
Features
Overview
■
The CapSense Express™ controller allows the control of eight
IOs configurable as capacitive sensing buttons or as GPIOs for
driving LEDs or interrupt signals based on various button
conditions. The GPIOs are also configurable for waking up the
device from sleep based on an interrupt input.
8 configurable IOs supporting
❐ CapSense™ buttons
❐ LED drive
❐ Interrupt outputs
❐ WAKE on interrupt input
❐ Bi-directional sleep control pin
❐ User defined input or output
■
2.4V to 2.9V, 3.10V to 3.6V, and 4.75V to 5.25V operating
voltage
■
Industrial temperature range: –40°C to +85°C
■
I2C slave interface for configuration
2
❐ I C data transfer rate up to 400 kbps
■
Reduce BOM cost
❐ Internal oscillator - no external oscillators or crystal
❐ Free development tool - no external tuning components
■
Low operating current
❐ Active current:1.5 mA
❐ Deep sleep current: 2.6 uA
■
Available in 16-pin COL and 16-pin SOIC packages
The user has the ability to configure buttons, outputs, and
parameters through specific commands sent to the I2C port. The
IOs have the flexibility of mapping to capacitive buttons and as
standard GPIO functions such as interrupt output or input, LED
drive, and digital mapping of input to output using simple logical
operations. This enables easy PCB trace routing and reduces
the PCB size and stack up. CapSense Express products are
designed for easy integration into complex products.
Architecture
The logic block diagram illustrates the internal architecture of
CY8C20180.
The user can configure registers with parameters needed to
adjust the operation and sensitivity of the CapSense system.
CY8C20180 supports a standard I2C serial communications
interface that allows the host to configure the device and to read
sensor information in real time through easy register access.
The CapSense Express Core
The CapSense Express core has a powerful configuration and
control block. It encompasses SRAM for data storage, an
interrupt controller, and sleep and watchdog timers. System
resources provide additional capability, such as a configurable
I2C slave communication interface and various system resets.
The analog system contains the CapSense PSoC® block which
supports capacitive sensing of up to eight inputs.
Cypress Semiconductor Corporation
Document Number: 001-17346 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised January 28, 2009
[+] Feedback
CY8C20180
Logic Block Diagram
External VCC
2.40V to 2.90V, 3.10V to
3.60V, 4.75V to 5.25V
8 Configurable IOs
CapSense ExpressTM
Core
SYSTEM BUS
512B SRAM
2 KB Flash
Sleep and
Watchdog
Configuration and
Control Engine
Interrupt
Controller
Clock Sources
(Internal Main Oscillator)
SYSTEM BUS
CapSense
Block
Document Number: 001-17346 Rev. *F
I2C Slave
Voltage &
Current
Reference
System
Reset
POR/LVD
Page 2 of 16
[+] Feedback
CY8C20180
Pinouts
Figure 1. Pin Diagram - 16 Pin COL
COL
(TOP VIEW)
Table 1. Pin Definitions - 16 Pin COL[1]
Pin Number
Name
Description
1
GP0[0]
Configurable as CapSense or GPIO
2
GP0[1]
Configurable as CapSense or GPIO
3
I2C SCL
I2C clock
4
I2C SDA
I2C data
5
GP1[0]
Configurable as CapSense or GPIO
6
GP1[1]
Configurable as CapSense or GPIO
7
VSS
8
GP1[2]
Configurable as CapSense or GPIO
9
GP1[3]
Configurable as CapSense or GPIO
10
GP1[4]
Configurable as CapSense or GPIO
11
XRES
Active HIGH external reset with internal pull down
12
GP0[2]
Configurable as CapSense or GPIO
13
VDD
14
GP0[3]
15
CSInt
16
GP0[4]
Ground connection
Supply voltage
Configurable as CapSense or GPIO
Integrating Input.The external capacitance is required only if 5:1 SNR cannot
be achieved. Typical range is 10 nF to 100 nF
Configurable as CapSense or GPIO
Note
1. 8 available configurable IOs can be configured to any of the 10 IOs of the package. After any of the 8 IOs are chosen, the remaining 2 IOs of the package get locked
and is not available for any functionality.
Document Number: 001-17346 Rev. *F
Page 3 of 16
[+] Feedback
CY8C20180
Figure 2. Pin Diagram - 16 Pin SOIC
GP0[3]
1
16
VDD
CSInt
2
15
GP0[2]
GP0[4]
3
14
XRES
GP0[0]
4
13
GP1[4]
GP0[1]
5
12
GP1[3]
I2CSCL
6
11
GP1[2]
I2CSDA
7
10
VSS
GP1[0]
8
9
SOIC
(Top View)
GP1[1]
Table 2. Pin Definitions - 16 Pin SOIC[1]
Pin Number
Name
1
GP0[3]
2
CSInt
3
GP0[4]
Configurable as CapSense or GPIO
4
GP0[0]
Configurable as CapSense or GPIO
5
GP0[1]
Configurable as CapSense or GPIO
6
I2C SCL
I2C clock
7
I2C SDA
I2C data
8
GP1[0]
Configurable as CapSense or GPIO
9
GP1[1]
Configurable as CapSense or GPIO
10
VSS
11
GP1[2]
Configurable as CapSense or GPIO
12
GP1[3]
Configurable as CapSense or GPIO
13
GP1[4]
Configurable as CapSense or GPIO
14
XRES
Active HIGH external reset with internal pull down
15
GP0[2]
Configurable as CapSense or GPIO
16
VDD
Document Number: 001-17346 Rev. *F
Description
Configurable as CapSense or GPIO
Integrating Input.The external capacitance is required only if 5:1 SNR cannot
be achieved. Typical range is 10 nF to 100 nF
Ground connection
Supply voltage
Page 4 of 16
[+] Feedback
CY8C20180
The CapSense Analog System
I2C Interface
The CapSense analog system contains the capacitive sensing
hardware. which supports CapSense Successive Approximation
(CSA) algorithm. This hardware performs capacitive sensing and
scanning without external components. Capacitive sensing is
configurable on each pin.
The two modes of operation for the I2C interface are:
Additional System Resources
The I2C address is programmable during configuration. It can be
locked to prevent accidental change by setting a flag in a configuration register.
System resources provide additional capability useful to
complete systems. Additional resources are low voltage
detection and power on reset (POR).
■
The I2C slave provides 50, 100, or 400 kHz communication
over two wires.
■
Low Voltage Detection (LVD) interrupts signal the application
of falling voltage levels and the advanced POR circuit eliminates the need for a system supervisor.
An internal 1.8V reference provides a stable internal reference
so that capacitive sensing functionality is not affected by minor
VDD changes.
■
Device register configuration and status read or write for
controller.
■
Command execution.
I2C Device Addressing
I2C device address is contained in the upper seven bits of the
first byte of a read or write transaction. The first byte of the transaction is used by the I2C master to address the slave. The LSB
of the byte contains the R/W bit. If this bit is 0, the master
performs write operation to the addressed slave. If this bit is 1,
the master performs read operation from the addressed slave.
The LSB(B0) is eliminated when fixing the device address. For
example, if the slave address is 02h, then the required address
is 0000010 (7 bit) excluding LSB. If write operation is performed,
the LSB is 0 and the address is 00000100(04h). If read operation
is performed, the LSB is 1 and the address is 00000101(05h).
Table 3 provides examples of I2C addressing.
Table 3. Examples of I2C Addressing
Slave Address
Defined
B7
B6
B5
B4
B3
B2
B1
B0
Address to be
sent (in Hex) by
Master
0
0
0
0
0
0
0
0
0(W)
00
0
0
0
0
0
0
0
0
1(R)
01
1
0
0
0
0
0
0
1
0(W)
02
1
0
0
0
0
0
0
1
1(R)
03
10
0
0
0
1
0
1
0
0(W)
14
10
0
0
0
1
0
1
0
1(R)
15
75
1
0
0
1
0
1
1
0(W)
96
75
1
0
0
1
0
1
1
1(R)
97
127
1
1
1
1
1
1
1
0(W)
FE
127
1
1
1
1
1
1
1
1(R)
FF
CapSense Express Software Tool
CapSense Express Register Map
An easy to use software tool integrated with PSoC Express is
available for configuring and tuning CapSense Express devices.
Refer to the application note “CapSense™ Express Software
Tool - AN42137” for details of the software tool.
CapSense Express supports user configurable registers through
which the device functionality and parameters are configured.
For details, refer to the CY8C201xx Register Reference Guide.
Document Number: 001-17346 Rev. *F
Page 5 of 16
[+] Feedback
CY8C20180
Modes of Operation
Deep Sleep Mode
CapSense Express devices are configured to operate in any of
the following three modes to meet different power consumption
requirements:
Deep sleep mode provides the lowest power consumption
because there is no operation running. In this mode, the device
is woken up only using an external GPIO interrupt. A sleep timer
interrupt cannot wake up a device from deep sleep mode. This
can be treated as a continuous sleep mode without periodic
wakeups. Refer to the application note “CapSense Express
Power and Sleep Considerations - AN44209” for details on
different sleep modes.
■
Active Mode
■
Sleep Mode
■
Deep Sleep Mode
Active Mode
Bi-Directional Sleep Control Pin
In the active mode, all the device blocks including the CapSense
sub system are powered. Typical active current consumption of
the device across the operating voltage range is 1.5 mA.
The CY8C20180 requires a dedicated sleep control pin to allow
reliable I2C communication in case any sleep mode is enabled.
This is achieved by pulling the sleep control pin LOW to wake up
the device and start I2C communication. The sleep control pin
can be configured on any of the GPIO. If sleep control feature is
enabled, the device has one less GPIO available for CapSense
and GPIO functions. The sleep control pin can also be
configured as interrupt output pin from CY8C20180 to the host
to acknowledge finger press on any button. To enable bi-directional feature, user must use I2C-USB bridge program.
Sleep Mode
Sleep mode provides an intermediate power operation mode. It
is enabled by configuring the corresponding device register.
When enabled, the device enters sleep mode and wakes up after
a specified sleep interval. It scans the capacitive sensors before
going back to sleep again. The device can also wake up from
sleep mode with a GPIO interrupt. The following sleep intervals
are supported in CapSense Express. The sleep interval is
configured through registers.
■
1.95 ms (512 Hz)
■
15.6 ms (64 Hz)
■
125 ms (8 Hz)
■
1s (1 Hz)
Document Number: 001-17346 Rev. *F
Page 6 of 16
[+] Feedback
CY8C20180
Electrical Specifications
Absolute Maximum Ratings
Parameter
Description
Min
Typ
Max
Unit
Notes
Higher storage temperatures reduce data
retention time. Recommended storage
temperature is +25°C ± 25°C (0°C to 50°C).
Extended duration storage temperatures
above 65°C degrade reliability
TSTG
Storage temperature
–55
25
+100
°C
TA
Ambient temperature with power
applied
–40
–
+85
ºC
VDD
Supply voltage on VDD relative to VSS
–0.5
–
+6.0
V
VIO
DC input voltage
VSS – 0.5
–
VDD + 0.5
V
VIOZ
DC voltage applied to tri-state
VSS – 0.5
–
VDD + 0.5
V
IMIO
Maximum current into any GPIO pin
–25
–
+50
mA
ESD
Electro static discharge voltage
2000
–
–
V
LU
Latch up current
–
–
200
mA
Min
Typ
Max
Unit
Human body model ESD
Operating Temperature
Parameter
Description
TA
Ambient temperature
–40
–
+85
°C
TJ
Junction temperature
–40
–
+100
°C
Notes
DC Electrical Characteristics
DC Chip Level Specifications
Min
Typ
Max
Unit
VDD
Parameter
Supply voltage
Description
2.40
–
5.25
V
IDD
Supply current
–
1.5
2.5
mA
Conditions are VDD = 3.10V, TA = 25°C
ISB
Deep sleep mode current with POR
and LVD active. Mid temperature
range
–
2.6
4
µA
VDD = 2.55V, 0°C < TA < 40°C
ISB
Deep sleep mode current with POR
and LVD active
–
2.8
5
µA
VDD = 3.3V, –40°C < TA < 85°C
ISB
Deep sleep mode current with POR
and LVD active
–
5.2
6.4
µA
VDD = 5.25V, –40°C < TA < 85°C
Document Number: 001-17346 Rev. *F
Notes
Page 7 of 16
[+] Feedback
CY8C20180
5 and 3.3V DC General Purpose IO Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and -40°C<
TA<85°C, 3.10V to 3.6V and -40°C<TA<85°C respectively. Typical parameters apply to 5V and 3.3V at 25°C. These are for design
guidance only.
Parameter
Description
Min
Typ
Max
Unit
4
5.6
8
kΩ
Notes
RPU
Pull up resistor
VOH1
High output voltage
Port 0 pins
VDD – 0.2
–
–
V
IOH = 10 µA, VDD > 3.10V, maximum of 20
mA source current in all IOs.
VOH2
High output voltage
Port 0 pins
VDD – 0.9
–
–
V
IOH = 1 mA, VDD > 3.10V, maximum of 20
mA source current in all IOs.
VOH3
High output voltage
Port 1 pins
VDD – 0.2
–
–
V
IOH < 10 µA, VDD> 3.10V, maximum of 10
mA source current in all IOs.
VOH
High output voltage
Port 1 pins
VDD – 0.9
–
–
V
IOH = 5 mA, VDD> 3.10V, maximum of 20
mA source current in all IOs.
VOL
Low output voltage
–
–
0.75
V
IOL = 20 mA, VDD > 3.10V, maximum of 60
mA sink current on even port pins and 60
mA sink current on odd port pins
VIL
Input low voltage
–
–
0.75
V
VDD = 3.10V to 3.6V.
VIH
Input high voltage
1.6
–
–
V
VDD = 3.10V to 3.6V.
VIL
Input low voltage
–
–
0.8
V
VDD = 4.75V to 5.25V.
VIH
Input high voltage
2.0
–
–
V
VDD = 4.75V to 5.25V.
VH
Input hysteresis voltage
–
140
–
mV
IL
Input leakage
–
1
–
nA
Gross tested to 1 µA.
CIN
Capacitive load on pins as input
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
COUT
Capacitive load on pins as output
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
Document Number: 001-17346 Rev. *F
Page 8 of 16
[+] Feedback
CY8C20180
2.7V DC General Purpose IO Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 2.4V to 2.90V and -40°C<.
TA <85°C, respectively. Typical parameters apply to 2.7V at 25°C. These are for design guidance only.
Parameter
Description
Min
Typ
Max
Unit
Notes
RPU
Pull up resistor
4
5.6
8
kΩ
VOH1
High output voltage
Port 0 pins
VDD – 0.2
–
–
V
IOH < 10 µA, maximum of 10 mA source
current in all IOs.
VOH2
High output voltage
Port 0 pins
VDD – 0.5
–
–
V
IOH = 0.2 mA, maximum of 10 mA source
current in all IOs.
VOH3
High output voltage
Port 1 pins
VDD – 0.2
–
–
V
IOH < 10 µA, maximum of 10 mA source
current in all IOs.
VOH4
High output voltage
Port 1 pins
VDD – 0.5
–
–
V
IOH = 2 mA, maximum of 10 mA source
current in all IOs.
VOL
Low output voltage
–
–
0.75
V
IOL = 10 mA, maximum of 30 mA sink current
on even port pins and 30 mA sink current on
odd port pins.
VOLP1
Low output voltage port 1 pins
–
–
0.4
V
IOL=5 mA, maximum of 50 mA sink current on
even port pins and 50 mA sink current on odd
port pins 2.4<VDD <2.9V and 3.1<VDD <3.6V.
VIL
Input low voltage
–
–
0.75
V
VDD = 2.4 to 2.90V and 3.10V to 3.6V.
–
–
V
VDD = 2.4 to 2.7V.
V
VDD = 2.7 to 2.90V and 3.10V to 3.6V.
VIH1
Input high voltage
1.4
VIH2
Input high voltage
1.6
VH
Input hysteresis voltage
–
60
–
mV
IIL
Input leakage
–
1
–
nA
Gross tested to 1 µA.
CIN
Capacitive load on pins as input
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
COUT
Capacitive load on pins as output
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
Document Number: 001-17346 Rev. *F
Page 9 of 16
[+] Feedback
CY8C20180
2.7V DC Spec for I2C Line with 1.8V External Pull Up
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 2.4V to 2.9V and 3.10V to
3.60V, and -40°C<TA <85°C, respectively. Typical parameters apply to 2.7V at 25°C. The I2C lines drive mode must be set to open
drain and pulled up to 1.8V externally.
Parameter
Description
Min
Typ
Max
Unit
Notes
VOLP1
Low output voltage port 1 pins
–
–
0.4
V
IOL=5mA, maximum of 50 mA sink
current on even port pins and 50 mA sink
current on odd port pins.
2.4<VDD <2.9V and 3.1<VDD <3.6V.
VIL
Input low voltage
–
–
0.75
V
VDD = 2.4 to 2.90V and 3.10V to 3.6V.
VIH
Input high voltage
1.4
–
–
V
VDD = 2.4 to 2.7V.
CIN
Capacitive load on pins as input
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
COUT
Capacitive load on pins as output
0.5
1.7
5
pF
Package and pin dependent.
Temp = 25°C.
Min
Typ
Max
Unit
Notes
–
–
2.36
2.60
2.40
2.65
V
V
VDD must be greater than or equal to 2.5V
during startup, reset from the XRES pin,
or reset from watchdog.
2.39
2.75
3.98
2.45
2.92
4.05
2.51
2.99
4.12
V
V
V
DC POR and LVD Specifications
Parameter
Description
VPPOR0
VPPOR1
VDD Value for PPOR Trip
VDD= 2.7V
VDD= 3.3V,5V
VLVD0
VLVD2
VLVD6
VDD Value for LVD Trip
VDD= 2.7V
VDD= 3.3V
VDD= 5V
Document Number: 001-17346 Rev. *F
Page 10 of 16
[+] Feedback
CY8C20180
DC Programming Specifications
This table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V and
-40°C<TA<85°C, 3.10V to 3.6V and -40°C<TA<85°C, or 2.4V to 2.90V and -40°C<TA<85°C, respectively. Typical parameters apply
to 5V, 3.3V, or 2.7V at 25°C. These are for design guidance only. Flash Endurance and Retention specifications with the use of
EEPROM user module are valid only within the range: 25°C±20°C during the Flash Write operation.
Refer to the EEPROM user module data sheet instructions for EEPROM Flash Write requirements outside the 25°C±20°C temperature
window. Use of this User Module for Flash Writes outside this range must occur at a known die temperature (±20°C) and requires the
designer to configure the temperature as a variable rather than the default 25°C value hard coded into the API. All use of this UM API
outside the range of 25°C±20°C is at the user’s own risk. This risk includes overwriting the Flash cell (when above the allowable
temperature range) thereby reducing the data sheet specified endurance performance or underwriting the Flash cell (when below the
allowable temperature range) thereby reducing the data sheet specified retention.
Symbol
Description
VddIWRITE Supply Voltage for Flash Write Operations[2]
IDDP
Supply Current During Programming or Verify
VILP
Input Low Voltage During Programming or
Verify
VIHP
Input High Voltage During Programming or
Verify
IILP
Input Current when Applying Vilp to P1[0] or
P1[1] During Programming or Verify
IIHP
Input Current when Applying Vihp to P1[0] or
P1[1] During Programming or Verify
VOLV
Output Low Voltage During Programming or
Verify
VOHV
Output High Voltage During Programming or
Verify
FlashENPB Flash Endurance (per block)
FlashENT Flash Endurance (total)
FlashDR
Flash Data Retention
Min
2.7
–
–
Typ
–
5
–
Max
–
25
0.8
Units
V
mA
V
2.2
–
–
V
–
–
0.2
mA
–
–
1.5
mA
–
–
V
Vdd
–1.0
50,000
1,800,0
00
10
–
Vss +
0.75
Vdd
–
–
–
–
–
–
–
–
Years
Notes
Driving internal pull down
resistor.
Driving internal pull down
resistor.
V
Erase/write cycles per block.
Erase/write cycles.
CapSense Electrical Characteristics
Max (V)
Typical (V)
Min (V)
Conditions for Supply Voltage
Result
3.6
3.3
3.10
<2.9V
The device automatically reconfigures itself to work
in 2.7V mode of operation.
3.10
2.7
2.45
<2.45V
The scanning for CapSense parameters shuts down
until the voltage returns to over 2.45V.
<2.4V
The device goes into reset.
3.6
3.3
3.10
>3.10V
The device automatically reconfigures itself to work
in 3.3V mode of operation.
5.25
5.0
4.75
<4.73V
The scanning for CapSense parameters shuts down
until the voltage returns to over 4.73V.
3.6 to 4.75V
This range is not supported by CapSense Express.
The device will work, but CapSense scanning is not
enabled until the voltage goes above 4.73V.
2.9 to 3.1V
This range is not supported by CapSense Express.
Note
2. Commands involving Flash Writes (0x01, 0x02, 0x03) must be executed only within the same VCC voltage range detected at POR (power on, XRES, or command
0x06) and above 2.7V. For register details, refer to CY8C201xx Register Reference Guide. If the user powers up the device in the 2.4V–3.6V range, Flash writes must
be performed only in the range 2.7V to 2.9V and 3.10V to 3.6V. If the user powers up the device in the 4.75V–5.25V range, Flash writes must be performed in that
range only.
Document Number: 001-17346 Rev. *F
Page 11 of 16
[+] Feedback
CY8C20180
AC Electrical Characteristics
5V and 3.3V AC General Purpose IO Specifications
Parameter
Description
Min
Max
Unit
Notes
TRise0
Rise time, strong mode,
Cload = 50 pF, Port 0
15
80
ns
VDD = 3.10V to 3.6V and 4.75V to
5.25V, 10% - 90%
TRise1
Rise time, strong mode,
Cload = 50 pF, Port 1
10
50
ns
VDD = 3.10V to 3.6V, 10% - 90%
TFall
Fall time, strong mode,
Cload = 50 pF, all ports
10
50
ns
VDD = 3.10V to 3.6V and 4.75V to
5.25V, 10% - 90%
Min
Max
Unit
2.7V AC General Purpose IO Specifications
Parameter
Description
Notes
TRise0
Rise time, strong mode,
Cload = 50 pF, Port 0
15
100
ns
VDD = 2.4V to 2.90V, 10% - 90%
TRise1
Rise time, strong mode,
Cload = 50 pF, Port 1
10
70
ns
VDD = 2.4V to 2.90V, 10% - 90%
TFall
Fall time, strong mode,
Cload = 50 pF, all ports
10
70
ns
VDD = 2.4V to 2.90V, 10% - 90%
AC I2C Specifications
Parameter
FSCLI2C
Description
SCL clock frequency
THDSTAI2C Hold time (repeated) START
condition. After this period, the
first clock pulse is generated
Standard Mode
Fast Mode
Unit
Min
Max
Min
Max
0
100
0
400
KHz
4.0
–
0.6
–
µs
TLOWI2C
LOW period of the SCL clock
4.7
–
1.3
–
µs
THIGHI2C
HIGH period of the SCL clock
4.0
–
0.6
–
µs
TSUSTAI2C
Setup time for a repeated START
condition
4.7
–
0.6
–
µs
THDDATI2C Data hold time
0
–
0
–
µs
TSUDATI2C Data setup time
250
–
100
–
ns
TSUSTOI2C Setup time for STOP condition
4.0
–
0.6
–
µs
TBUFI2C
BUS free time between a STOP
and START condition
4.7
–
1.3
–
µs
TSPI2C
Pulse width of spikes suppressed
by the input filter
–
–
0
50
ns
Document Number: 001-17346 Rev. *F
Notes
Fast mode not supported for
VDD < 3.0V
Page 12 of 16
[+] Feedback
CY8C20180
~
~
~
~
Figure 3. Definition of Timing for Fast/Standard Mode on the I2C Bus
tf
~
~
tf
tSUDATI2C
tr
tLOWI2C
~
~
SDA
tHDSTAI2C
tSPI2C
tBUFI2C
tr
S
tHDSTAI2C
tSUSTAI2C
tHIGHI2C
tHDDATI2C
~
~
~
~
SCL
tSUSTOI2C
Sr
P
S
Ordering Information
Ordering Code
Package Diagram
Package Type
Operating Temperature
CY8C20180-LDX2I
001-09116
16 COL[5]
Industrial
CY8C20180-SX2I
51-85068
16 SOIC
Industrial
Thermal Impedances by Package
Typical θJA[3]
Package
16
COL[5]
46 °C
16 SOIC
79.96 °C
Solder Reflow Peak Temperature
Package
16 COL
[5]
16 SOIC
Minimum Peak Temperature[4]
Maximum Peak Temperature
240 °C
260 °C
240 °C
260 °C
.
Notes
3. TJ = TA + Power x θJA.
4. Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5°C with Sn-Pb or 245 ± 5°C with Sn-Ag-Cu paste.
Refer to the solder manufacturer specifications.
5. Earlier termed as QFN package.
Document Number: 001-17346 Rev. *F
Page 13 of 16
[+] Feedback
CY8C20180
Package Diagrams
Figure 4. 16L Chip On Lead 3 X 3 mm Package Outline (SAWN) - 001-09116 - (Pb-Free)
001-09116 *D
Figure 5. 16-Pin (150-Mil) SOIC (51-85068)
51-85068-*B
Document Number: 001-17346 Rev. *F
Page 14 of 16
[+] Feedback
CY8C20180
Document History Page
Document Title: CY8C20180 CapSense Express™ - 8 Configurable IOs
Document Number: 001-17346
Rev.
ECN No.
Orig. of
Change
Submission
Date
Description of Change
**
1341766
TUP/FSU
See ECN
New Data Sheet
*A
1494145
TUP/AESA
See ECN
Changed to FINAL Datasheet
Removed table - 2.7V DC General Purpose IO Specifications - Open Drain with
a pull up to 1.8V
Updated Logic Block Diagram
*B
1773608
TUP/AESA
See ECN
Removed table - 3V DC General Purpose IO Specifications
Updated Logic Block Diagram
Updated table - DC POR and LVD Specifications
Updated table - DC Chip Level Specifications
Updated table - 5V and 3.3V DC General Purpose IO Specifications
Updated table - 2.7V DC General Purpose IO Specifications
Updated table - AC GPIO Specifications and split it into two tables for 5V/3.3V
and 2.7V
Added section on CapSense ExpressTM Software tool
Updated 16-QFN Package Diagram
*C
2091026
DZU/MOHD
/AESA
See ECN
Updated table-DC Chip Level Specifications
Updated table-Pin Definitions 16 pin COL
Updated table-Pin Definitions 16 pin SOIC
Updated table-5V and 3.3V DC General Purpose IO Specifications
Updated table - 2.7V DC General Purpose IO Specifications
Changed definition for Timing for Fast/Standard Mode on the I2C Bus diagram
*D
2404731
DZU/MOHD/
PYRS
See ECN
Updated Logic Block Diagram
Added DC Programming Specifications Table
Updated Features
Added CapSense Electrical Characteristics Table
*E
2544918
ZSK/AESA
09/06/2008
*F
2648811
DZU/PYRS
01/28/09
Document Number: 001-17346 Rev. *F
Different sleep modes explained
Bi-Directional Sleep Control Pin defined
Table added on “2.7V DC Spec for I2C Line with 1.8V External Pull-Up
Included section on I2C Device Addressing
Updated CapSense Electrical Specifications table
Deleted VOH5, VOH6, VOH7, and VOH8 parameters
Page 15 of 16
[+] Feedback
CY8C20180
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC Solutions
PSoC
psoc.cypress.com
Clocks & Buffers
Wireless
Memories
clocks.cypress.com
General
Low Power/Low Voltage
psoc.cypress.com/solutions
psoc.cypress.com/low-power
wireless.cypress.com
Precision Analog
memory.cypress.com
LCD Drive
psoc.cypress.com/lcd-drive
CAN 2.0b
psoc.cypress.com/can
USB
psoc.cypress.com/usb
Image Sensors
image.cypress.com
psoc.cypress.com/precision-analog
© Cypress Semiconductor Corporation, 2007-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-17346 Rev. *F
Revised January 28, 2009
Page 16 of 16
CapSense Express™, PSoC Designer™, Programmable System-on-Chip™, and PSoC Express™ are trademarks and PSoC® is a registered trademark of Cypress Semiconductor Corp. All other
trademarks or registered trademarks referenced herein are property of the respective corporations. Purchase of I2C components from Cypress or one of its sublicensed Associated Companies conveys
a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. All products and
company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback