CYPRESS CY7C60445

PRELIMINARY
CY7C60445, CY7C6045x
enCoRe™ V Low Voltage Microcontroller
Features
■
Powerful Harvard Architecture Processor
❐ M8C processor speeds running up to 24 MHz
❐ Low power at high processing speeds
❐ Interrupt controller
❐ 1.71V to 3.6V operating voltage
❐ Temperature range: 0°C to 70°C
■
Flexible On-Chip Memory
❐ Up to 32K Flash program storage
50,000 Erase/write cycles
❐ Up to 2048 bytes SRAM data storage
❐ Flexible protection modes
❐ In-System Serial Programming (ISSP)
■
Complete Development Tools
❐ Free development tool (PSoC Designer™)
❐ Full featured, in-circuit emulator and programmer
❐ Full speed emulation
❐ Complex breakpoint structure
❐ 128K trace memory
■
Precision, Programmable Clocking
❐ Crystal-less oscillator with support for an external crystal or
resonator
❐ Internal ±5.0% 6, 12, or 24 MHz main oscillator
❐ Internal low speed oscillator at 32 kHz for watchdog and
sleep.The frequency range is 19–50 kHz with a 32 kHz typical
value
■
Programmable Pin Configurations
❐ 25 mA sink current on all GPIO
❐ Pull up, high Z, open drain, CMOS drive modes on all GPIO
❐ Configurable inputs on all GPIO
❐ Low dropout voltage regulator for Port1 pins. Programmable
to output 3.0, 2.5, or 1.8V at the I/O pins
❐ Selectable, regulated digital IO on Port 1
• Configurable input threshold for Port 1
• 3.0V, 20 mA total Port 1 source current
• Hot-swappable
❐ 5 mA strong drive mode on Ports 0 and 1
■
Additional System Resources
❐ Configurable communication speeds
2
❐ I C™ Slave
• Selectable to 50 kHz, 100 kHz, or 400 kHz
• Implementation requires no clock stretching
• Implementation during sleep modes with less than 100 mA
• Hardware address detection
❐ SPI master and SPI slave
• Configurable between 46.9 kHz and 3 MHz
❐ Three 16-bit timers
❐ 10-bit ADC for monitoring battery voltage or other signals
❐ Watchdog and sleep timers
❐ Integrated supervisory circuit
enCoRe V LV Block Diagram
enCoRe V
Low Voltage
CORE
Port 4
Port 3
Port 2
Port 1
Port 0
Prog. LDO
System Bus
SRAM
2048 Bytes
Interrupt
Controller
SROM
Flash 32K
CPU Core
(M8C)
Sleep and
Watchdog
6/12/24 MHz Internal Main Oscillator
3 16-Bit
Timers
POR and LVD
I2C Slave/SPI
Master-Slave
System Resets
SYSTEM RESOURCES
Cypress Semiconductor Corporation
Document Number: 001-12395 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 19, 2008
[+] Feedback
PRELIMINARY
Functional Overview
The enCoRe V LV family of devices are designed to replace
multiple traditional low voltage microcontroller system components with one, low cost single chip programmable component.
Communication peripherals (I2C/SPI), a fast CPU, Flash
program memory, SRAM data memory, and configurable IO are
included in a range of convenient pinouts.
The architecture for this device family, as illustrated in enCoRe
V LV Block Diagram, is comprised of two main areas: the CPU
core and the system resources. Depending on the enCoRe V LV
package, up to 36 general purpose IO (GPIO) are also included.
Enhancements over the Cypress’ legacy low voltage microcontrollers include faster CPU at lower voltage operation, lower
current consumption, twice the RAM and Flash, hot-swapable
IOs, I2C hardware address recognition, new very low current
sleep mode, and new package options.
The enCoRe V LV Core
The enCoRe V LV Core is a powerful engine that supports a rich
instruction set. It encompasses SRAM for data storage, an
interrupt controller, sleep and watchdog timers, and IMO
(internal main oscillator) and ILO (internal low speed oscillator).
The CPU core, called the M8C, is a powerful processor with
speeds up to 24 MHz. The M8C is a four-MIPS, 8-bit Harvard
architecture microprocessor.
System Resources provide additional capability, such as a
configurable I2C slave and SPI master-slave communication
interface and various system resets supported by the M8C.
Additional System Resources
System Resources, some of which have been previously listed,
provide additional capability useful to complete systems.
Additional resources include low voltage detection and power on
reset. Brief statements describing the merits of each system
resource are presented below.
■
10-bit on-chip ADC shared between System Performance
manager (used to calculate parameters based on temperature
for flash write operations) and the user.
■
The I2C slave and SPI master-slave module provides 50, 100,
or 400 kHz communication over two wires. SPI communication
over 3 or 4 wires runs at speeds of 46.9 kHz to 3 MHz (lower
for a slower system clock).
■
In I2C Slave mode the hardware address recognition feature
reduces the already low power consumption by eliminating the
need for CPU intervention until a packet addressed to the target
device has been received.
Document Number: 001-12395 Rev. *F
CY7C60445, CY7C6045x
■
Low Voltage Detection (LVD) interrupts can signal the application of falling voltage levels, while the advanced POR (Power
On Reset) circuit eliminates the need for a system supervisor.
■
The 5V maximum input, 1.8, 2.5, or 3V selectable output, low
dropout regulator (LDO) provides regulation for IOs. A register
controlled bypass mode allows the user to disable the LDO.
■
Standard Cypress PSoC IDE tools are available for debugging
the enCoRe V LV family of parts.
Getting Started
The quickest path to understanding the enCoRe V LV silicon is
by reading this data sheet and using the PSoC Designer
Integrated Development Environment (IDE). This data sheet is
an overview of the enCoRe V LV integrated circuit and presents
specific pin, register, and electrical specifications.
For up to date ordering, packaging, and electrical specification
information, refer the latest enCoRe V LV device data sheet at
http://www.cypress.com.
Development Kits
Development Kits are available from the following distributors:
Digi-Key, Avnet, Arrow, and Future. The Cypress Online Store
contains development kits, C compilers, and all accessories for
PSoC development. Go to the Cypress Online Store web site at
http://www.cypress.com, click the Online Store shopping cart
icon at the bottom of the web page, and click on USB (Universal
Serial Bus) to view a current list of available items.
Technical Training
Free enCoRe V LV microcontrollers technical training is available
for beginners and is taught by a marketing or application
engineer over the phone. Low voltage microcontroller training
classes cover designing, debugging, analog, and application
specific classes covering topics such as PSoC, USB and the LIN
bus. Go to http://www.cypress.com, click on Design Support
located on the left side of the web page, and select Technical
Training for more details.
Consultants
Certified Cypress consultants offer everything from technical
assistance to completed microcontroller designs. To contact or
become a Cypress PSoC/USB/microcontroller consultant go to
http://www.cypress.com, click on Design Support located on the
left side of the web page, and select CYPros Consultants.
Technical Support
Cypress application engineers take pride in fast and accurate
response. They can be reached with a 4-hour guaranteed
response at http://www.cypress.com/support/login.cfm.
Page 2 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Development Tools
PSoC Designer Software Subsystems
PSoC Designer is a Microsoft® Windows based, integrated
development
environment
for
the
Programmable
System-on-Chip (PSoC) devices. The PSoC Designer IDE and
application runs on Windows NT 4.0, Windows 2000, Windows
Millennium (Me), or Windows XP. (Reference the PSoC Designer
Functional Flow diagram below.)
Device Editor
PSoC Designer helps the customer to select an operating configuration for the microcontroller, write application code that uses
its resources, and debug the application. This system provides
design database management by project, an integrated
debugger with In-Circuit Emulator, in-system programming
support, and the CYASM macro assembler for the CPUs.
PSoC Designer also supports a high level C language compiler
developed specifically for the devices in the family.
Figure 1. PSoC Designer Subsystems
The device editor subsystem allows the user to select different
onboard analog and digital components called user modules
using the enCoRe V LV device blocks. Examples of user
modules are timers, 10-bit ADC, and SPI/I2C.
The device editor also supports easy development of multiple
configurations and dynamic reconfiguration. Dynamic reconfiguration allows changing configurations at run time.
PSoC Designer sets up power on initialization tables for selected
enCoRe V LV block configurations and creates source code for
an application framework. The framework contains software to
operate the selected components and, if the project uses more
than one operating configuration, contains routines to switch
between different sets of enCoRe V LV block configurations at
run time. PSoC Designer prints out a configuration sheet for a
given project configuration for use during application
programming in conjunction with the device data sheet. When
the framework is generated, the user can add application specific
code to flesh out the framework. It is also possible to change the
selected components and regenerate the framework.
Application Editor
In the Application Editor you can edit your C language and
Assembly language source code. You can also assemble,
compile, link, and build.
Assembler. The macro assembler allows merging of assembly
code seamlessly with C code. The link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
C Language Compiler. A C language compiler is available that
supports the enCoRe V LV family of devices. Even if you have
never worked in C language before, the product allows you to
create complete C programs for the enCoRe V LV family devices.
The embedded, optimizing C compiler provides all the features
of C tailored to the enCoRe V LV architecture. It comes complete
with embedded libraries providing port and bus operations,
standard keypad and display support, and extended math
functionality.
Debugger
The PSoC Designer Debugger subsystem provides hardware
in-circuit emulation, allowing the designer to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow the designer to read the
program and read and write data memory, read and write IO
registers, read and write CPU registers, set and clear breakpoints, and provide program run, halt, and step control. The
debugger also allows the designer to create a trace buffer of
registers and memory locations of interest.
Online Help System
The online help system displays online, context sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer in getting started.
Document Number: 001-12395 Rev. *F
Page 3 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Hardware Tools
Figure 2. User Module and Source Code Development Flows
In-Circuit Emulator
Device Editor
A low cost, high functionality ICE (In-Circuit Emulator) is
available for development support. This hardware has the
capability to program single devices.
The emulator consists of a base unit that connects to the PC by
way of a USB port. The base unit is universal and operates with
most Cypress USB devices and all PSoC devices. Emulation
pods for each device family are available separately. The
emulation pod takes the place of the enCoRe V LV in the target
board and performs full speed (24 MHz) operation.
Designing with User Modules
To speed the development process, the PSoC Designer
Integrated Development Environment (IDE) provides a feature
where the resources of the part can be selected as user
modules. For example, the timers, I2C, SPI resources are
available as user modules. User modules make selecting and
implementing peripheral devices simple and easy.
Each user module establishes the basic register settings that
implement the selected function. It also provides parameters that
allow you to tailor its precise configuration to your particular
application. User modules also provide tested software to cut
your development time. The user module application
programming interface (API) provides high level functions to
control and respond to hardware events at run time. The API also
provides optional interrupt service routines that you can adapt as
needed.
The API functions are documented in user module data sheets
that are viewed directly in the PSoC Designer IDE. These data
sheets explain the internal operation of the user module and
provide performance specifications. Each data sheet describes
the use of each user module parameter and documents the
setting of each register controlled by the user module.
The development process starts when you open a new project
and bring up the Device Editor, a graphical user interface (GUI)
to configure the hardware. Pick and place the user modules
required for your project. The tool automatically builds signal
chains by connecting user modules to the default IO pins or as
required. At this stage, configure the clock source connections
and enter parameter values directly or by selecting values from
drop-down menus. When you are ready to test the hardware
configuration or move on to developing code for the project,
perform the “Generate Application” step. This causes PSoC
Designer to generate source code that automatically configures
the device to your specification and provides the high level user
module API functions.
User
Module
Selection
Source
Code
Generator
Generate
Application
Application Editor
Project
Manager
Source
Code
Editor
Build
Manager
Build
All
Debugger
Interface
to ICE
Storage
Inspector
Event &
Breakpoint
Manager
The next step is to write your main program, and any sub routines
using PSoC Designer’s Application Editor subsystem. The Application Editor includes a Project Manager that allows you to open
the project source code files (including all generated code files)
from a hierarchal view. The source code editor provides syntax
coloring and advanced edit features for both C and assembly
language. File search capabilities include simple string searches
and recursive “grep-style” patterns. A single mouse click invokes
the Build Manager. It employs a professional strength “makefile”
system to automatically analyze all file dependencies and run the
compiler and assembler as necessary. Project level options
control optimization strategies used by the compiler and linker.
Syntax errors are displayed in a console window. Double clicking
the error message takes you directly to the offending line of
source code. When all is correct, the linker builds a HEX file
image suitable for programming.
The last step in the development process takes place inside the
PSoC Designer’s Debugger subsystem. The Debugger
downloads the HEX image to the In-Circuit Emulator (ICE) where
it runs at full speed. Debugger capabilities rival those of systems
costing many times more. In addition to traditional single step,
run-to-breakpoint and watch-variable features, the Debugger
provides a large trace buffer and allows you define complex
breakpoint events that include monitoring address and data bus
values, memory locations, and external signals.
Document Number: 001-12395 Rev. *F
Page 4 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Document Conventions
Acronyms Used
Units of Measure
The following table lists the acronyms that are used in this
document.
A units of measure table is located in the Electrical Specifications
section. Table 6 on page 14 lists all the abbreviations used to
measure the enCoRe V LV devices.
Acronym
Description
API
application programming interface
CPU
central processing unit
GPIO
general purpose IO
GUI
graphical user interface
ICE
in-circuit emulator
ILO
internal low speed oscillator
IMO
internal main oscillator
IO
input/output
LSb
least significant bit
LVD
low voltage detect
MSb
most significant bit
POR
power on reset
PPOR
precision power on reset
PSoC®
Programmable System-on-Chip™
SLIMO
slow IMO
SRAM
static random access memory
Document Number: 001-12395 Rev. *F
Numeric Naming
Hexidecimal numbers are represented with all letters in
uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or
‘3Ah’). Hexidecimal numbers may also be represented by a ‘0x’
prefix, the C coding convention. Binary numbers have an
appended lowercase ‘b’ (e.g., 01010100b’ or ‘01000011b’).
Numbers not indicated by an ‘h’, ‘b’, or 0x are decimal.
Page 5 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Pin Configuration
32-Pin Part Pinout
P0[3]
P0[5]
P0[7]
Vdd
P0[6]
P0[4]
P0[2]
30
29
28
27
26
25
Vss
32
31
Figure 3. CY7C60445 32-Pin enCoRe V LV Device
QFN
12
13
14
15
16
P1[0]
P1[4]
P1[6]
P1[2]
11
P2[4]
P2[2]
P2[0]
P3[2]
Vss
(Top View)
22
21
20
19
18
17
P1[1]
3
4
5
6
7
8
P0[0]
P2[6]
P1[3]
P2[5]
P2[3]
P2[1]
P3[3]
P3[1]
P1[7]
24
23
9
10
1
2
P1[5]
P0[1]
P2[7]
P3[0]
XRES
Table 1. 32-Pin Part Pinout (QFN)
Pin No.
Type
1
IOH
P0[1]
Name
Digital IO
Description
2
IO
P2[7]
Digital IO
3
IO
P2[5]
Digital IO, Crystal Out (Xout)
4
IO
P2[3]
Digital IO, Crystal In (Xin)
5
IO
P2[1]
Digital IO
6
IO
P3[3]
Digital IO
7
IO
P3[1]
Digital IO
8
IOHR
P1[7]
Digital IO, I2C SCL, SPI SS
9
IOHR
P1[5]
Digital IO, I2C SDA, SPI MISO
10
IOHR
P1[3]
Digital IO, SPI CLK
11
IOHR
P1[1](1, 2)
Digital IO, ISSP CLK, I2C SCL, SPI MOSI
12
Power
Vss
Ground connection
13
IOHR
P1[0](1, 2)
Digital IO, ISSP DATA, I2C SDA, SPI CLK
Note
1. During power up or reset event, device P1[0] and P1[1] may disturb the I2C bus. Use alternate pins if issues are encountered.
2. These are the in-system serial programming (ISSP) pins, that are not High Z at power on reset (POR).
Document Number: 001-12395 Rev. *F
Page 6 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 1. 32-Pin Part Pinout (QFN) (continued)
Pin No.
Type
Name
Description
14
IOHR
P1[2]
Digital IO
15
IOHR
P1[4]
Digital IO, optional external clock input (EXTCLK)
16
IOHR
P1[6]
Digital IO
17
Reset Input
XRES
Active high external reset with internal pull down
18
IO
P3[0]
Digital IO
19
IO
P3[2]
Digital IO
20
IO
P2[0]
Digital IO
21
IO
P2[2]
Digital IO
22
IO
P2[4]
Digital IO
23
IO
P2[6]
Digital IO
24
IOH
P0[0]
Digital IO
25
IOH
P0[2]
Digital IO
26
IOH
P0[4]
Digital IO
27
IOH
P0[6]
Digital IO
28
Power
Vdd
Supply voltage
29
IOH
P0[7]
Digital IO
30
IOH
P0[5]
Digital IO
31
IOH
P0[3]
Digital IO
32
Power
Vss
Ground connection
CP
Power
Vss
Center pad must be connected to ground
LEGEND I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output.
Document Number: 001-12395 Rev. *F
Page 7 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
48-Pin Part Pinout
P0[0]
37
P0[4]
P0[6]
P0[2]
38
39
Vdd
40
P0[7]
42
41
P0[5]
44
NC
NC
P0[3]
45
43
Vss
46
P0[1]
48
47
Figure 4. CY7C60455/CY7C60456 48-Pin enCoRe V LV Device
36
P2[6]
2
35
P2[4]
3
34
P2[2]
4
33
P2[0]
P2[1]
P4[3]
5
32
P4[2]
31
P4[0]
P4[1]
7
30
P3[6]
P3[7]
8
9
29
28
P3[4]
P3[5]
P3[3]
10
27
P3[1]
11
P1[7]
12
26
25
P3[0]
XRES
1
P2[7]
P2[5]
P2[3]
QFN
6
13
14
15
16
17
18
19
20
21
22
23
24
P1[5]
NC
NC
P1[3]
P1[1]
Vss
NC
NC
Vdd
P1[0]
P1[2]
(Top View)
P3[2]
P1[6]
P1[4]
NC
Table 2. 48-Pin Part Pinout (QFN)
Pin No.
Type
Name
1
NC
NC
2
IO
P2[7]
Digital I/O
3
IO
P2[5]
Digital I/O, Crystal Out (Xout)
4
IO
P2[3]
Digital I/O, Crystal In (Xin)
5
IO
P2[1]
Digital I/O
6
IO
P4[3]
Digital I/O
7
IO
P4[1]
Digital I/O
8
IO
P3[7]
Digital I/O
9
IO
P3[5]
Digital I/O
10
IO
P3[3]
Digital I/O
11
IO
P3[1]
Digital I/O
12
IOHR
P1[7]
Digital I/O, I2C SCL, SPI SS
13
IOHR
P1[5]
Digital I/O, I2C SDA, SPI MISO
14
NC
NC
No connection
15
NC
NC
No connection
Document Number: 001-12395 Rev. *F
Description
No connection
Page 8 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 2. 48-Pin Part Pinout (QFN) (continued)
Pin No.
Type
16
IOHR
Name
P1[3]
(1, 2)
P1[1]
Description
Digital I/O, SPI CLK
17
IOHR
Digital I/O, ISSP CLK, I2C SCL, SPI MOSI
18
Power
Vss
Supply ground
19
NC
NC
No connection
20
NC
NC
No connection
21
Power
Vdd
Supply voltage
(1, 2)
22
IOHR
P1[0]
Digital I/O, ISSP DATA, I2C SDA, SPI CLK
23
IOHR
P1[2]
Digital I/O
24
IOHR
P1[4]
Digital I/O, optional external clock input (EXTCLK)
25
IOHR
P1[6]
Digital I/O
26
XRES
Ext Reset
Active high external reset with internal pull down
27
IO
P3[0]
Digital I/O
28
IO
P3[2]
Digital I/O
29
IO
P3[4]
Digital I/O
30
IO
P3[6]
Digital I/O
31
IO
P4[0]
Digital I/O
32
IO
P4[2]
Digital I/O
33
IO
P2[0]
Digital I/O
34
IO
P2[2]
Digital I/O
35
IO
P2[4]
Digital I/O
36
IO
P2[6]
Digital I/O
37
IOH
P0[0]
Digital I/O
38
IOH
P0[2]
Digital I/O
39
IOH
P0[4]
Digital I/O
40
IOH
P0[6]
Digital I/O
41
Power
Vdd
Supply voltage
42
NC
NC
No connection
43
NC
NC
No connection
44
IOH
P0[7]
Digital I/O
45
IOH
P0[5]
Digital I/O
46
IOH
P0[3]
Digital I/O
47
Power
Vss
Supply ground
48
IOH
P0[1]
Digital I/O
CP
Power
Vss
Center pad must be connected to ground
LEGEND I = Input, O = Output, OH = 5 mA High Output Drive, R = Regulated Output
Document Number: 001-12395 Rev. *F
Page 9 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Register Reference
The section discusses the registers of the enCoRe V LV device. It lists all the registers in mapping tables, in address order.
Register Conventions
Register Mapping Tables
The register conventions specific to this section are listed in the
following table.
The enCoRe V LV device has a total register address space of
512 bytes. The register space is also referred to as IO space and
is broken into two parts: Bank 0 (user space) and Bank 1 (configuration space). The XIO bit in the Flag register (CPU_F) determines which bank the user is currently in. When the XIO bit is
set, the user is said to be in the “extended” address space or the
“configuration” registers.
Table 3. Register Conventions
Convention
Description
R
Read register or bits
W
Write register or bits
O
Only a read/write register or bits
L
Logical register or bits
C
Clearable register or bits
#
Access is bit specific
Table 4. Register Map Bank 0 Table: User Space
Addr
Addr
Name
Name
(0,Hex) Access
(0,Hex) Access
PRT0DR
00
RW
40
PRT0IE
01
RW
41
02
42
03
43
PRT1DR
04
RW
44
PRT1IE
05
RW
45
06
46
07
47
PRT2DR
08
RW
48
PRT2IE
09
RW
49
0A
4A
0B
4B
PRT3DR
0C
RW
4C
PRT3IE
0D
RW
4D
0E
4E
0F
4F
PRT4DR
10
RW
50
PRT4IE
11
RW
51
12
52
13
53
14
54
15
55
16
56
17
57
18
58
19
59
1A
5A
1B
5B
1C
5C
1D
5D
1E
5E
1F
5F
20
60
21
61
22
62
23
63
24
64
Gray fields are reserved and should not be accessed.
# Access is bit specific.
Name
Document Number: 001-12395 Rev. *F
Addr
Addr
Name
(0,Hex) Access
(0,Hex) Access
80
C0
81
C1
82
C2
83
C3
84
C4
85
C5
86
C6
87
C7
88
I2C_XCFG
C8
RW
89
I2C_XSTAT
C9
R
8A
I2C_ADDR
CA
RW
8B
I2C_BP
CB
R
8C
I2C_CP
CC
R
8D
CPU_BP
CD
RW
8E
CPU_CP
CE
R
8F
I2C_BUF
CF
RW
90
CUR_PP
D0
RW
91
STK_PP
D1
RW
92
D2
93
IDX_PP
D3
RW
94
MVR_PP
D4
RW
95
MVW_PP
D5
RW
96
I2C_CFG
D6
RW
97
I2C_SCR
D7
#
98
I2C_DR
D8
RW
99
D9
9A
INT_CLR0
DA
RW
9B
INT_CLR1
DB
RW
9C
INT_CLR2
DC
RW
9D
INT_CLR3
DD
RW
9E
INT_MSK2
DE
RW
9F
INT_MSK1
DF
RW
A0
INT_MSK0
E0
RW
A1
INT_SW_EN
E1
RW
A2
INT_VC
E2
RC
A3
RES_WDT
E3
W
A4
INT_MSK3
E4
RW
Page 10 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 4. Register Map Bank 0 Table: User Space (continued)
Addr
Addr
Name
Name
(0,Hex) Access
(0,Hex) Access
25
65
26
66
27
67
28
68
SPI_TXR
29
W
69
SPI_RXR
2A
R
6A
SPI_CR
2B
#
6B
2C
6C
2D
6D
2E
6E
2F
6F
30
70
PT0_CFG
31
71
PT0_DATA1
32
72
PT0_DATA0
33
73
PT1_CFG
34
74
PT1_DATA1
35
75
PT1_DATA0
36
76
PT2_CFG
37
77
PT2_DATA1
38
78
PT2_DATA0
39
79
3A
7A
3B
7B
3C
7C
3D
7D
3E
7E
3F
7F
Gray fields are reserved and should not be accessed.
# Access is bit specific.
Name
Document Number: 001-12395 Rev. *F
Addr
Name
(0,Hex) Access
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
RW
B1
RW
B2
RW
B3
RW
B4
RW
B5
RW
B6
RW
B7
RW
CPU_F
B8
RW
B9
BA
BB
BC
BD
BE
CPU_SCR1
BF
CPU_SCR0
Addr
(0,Hex) Access
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
RL
F8
F9
FA
FB
FC
FD
FE
#
FF
#
Page 11 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 5. Register Map Bank 1 Table: Configuration Space
Addr
Addr
Addr
Access
Name
Access
Name
(1,Hex)
(1,Hex)
(1,Hex)
PRT0DM0
00
RW
40
80
PRT0DM1
01
RW
41
81
02
42
82
03
43
83
PRT1DM0
04
RW
44
84
PRT1DM1
05
RW
45
85
06
46
86
07
47
87
PRT2DM0
08
RW
48
88
PRT2DM1
09
RW
49
89
0A
4A
8A
0B
4B
8B
PRT3DM0
0C
RW
4C
8C
PRT3DM1
0D
RW
4D
8D
0E
4E
8E
0F
4F
8F
PRT4DM0
10
RW
50
90
PRT4DM1
11
RW
51
91
12
52
92
13
53
93
14
54
94
15
55
95
16
56
96
17
57
97
18
58
98
19
59
99
1A
5A
9A
1B
5B
9B
1C
5C
9C
1D
5D
9D
1E
5E
9E
1F
5F
9F
20
60
A0
21
61
A1
22
62
A2
23
63
A3
24
64
A4
25
65
A5
26
66
A6
27
67
A7
28
68
A8
SPI_CFG
29
RW
69
A9
2A
6A
AA
2B
6B
AB
2C
TMP_DR0
6C
RW
AC
2D
TMP_DR1
6D
RW
AD
2E
TMP_DR2
6E
RW
AE
2F
TMP_DR3
6F
RW
AF
30
70
B0
31
71
B1
32
72
B2
33
73
B3
34
74
B4
35
75
B5
36
76
B6
37
77
B7
38
78
B8
39
79
B9
3A
7A
BA
Gray fields are reserved and should not be accessed.
# Access is bit specific.
Name
Document Number: 001-12395 Rev. *F
Access
Addr
(1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
IO_CFG
DC
OUT_P1
DD
DE
DF
OSC_CR0 E0
ECO_CFG E1
OSC_CR2 E2
VLT_CR
E3
VLT_CMP E4
E5
E6
E7
IMO_TR
E8
ILO_TR
E9
EA
SLP_CFG EB
SLP_CFG2 EC
SLP_CFG3 ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
CPU_F
F7
F8
F9
FA
Name
Access
RW
RW
RW
#
RW
RW
R
W
W
RW
RW
RW
RL
Page 12 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 5. Register Map Bank 1 Table: Configuration Space
Addr
Addr
Addr
Name
Name
(1,Hex) Access
(1,Hex) Access
(1,Hex)
3B
7B
BB
3C
7C
BC
3D
7D
BD
3E
7E
BE
3F
7F
BF
Gray fields are reserved and should not be accessed.
# Access is bit specific.
Name
Document Number: 001-12395 Rev. *F
Access
Name
Addr
(1,Hex)
FB
FC
FD
FE
FF
Access
Page 13 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Electrical Specifications
This section presents the DC and AC electrical specifications of the enCoRe V LV devices. For the most up to date electrical
specifications, verify that you have the most recent data sheet available by visiting the company web site at http://www.cypress.com.
Figure 5. Voltage versus CPU Frequency
Figure 6. IMO Frequency Trim Options
3.6V
3.6V
lid ng
Va rati n
pe gio
Re
Vdd Voltage
Vdd Voltage
O
SLIMO
Mode
= 01
SLIMO
Mode
= 00
SLIMO
Mode
= 10
1.71V
1.71V
750 kHz
3 MHz
24 MHz
750 kHz
CPU Frequency
3 MHz
6 MHz 12 MHz 24 MHz
IMO Frequency
The following table lists the units of measure that are used in this chapter.
Table 6. Units of Measure
Symbol
oC
dB
fF
Hz
KB
Kbit
kHz
kΩ
MHz
MΩ
μA
μF
μH
μs
μV
μVrms
Unit of Measure
degree Celsius
decibels
femto farad
hertz
1024 bytes
1024 bits
kilohertz
kilohm
megahertz
megaohm
microampere
microfarad
microhenry
microsecond
microvolts
microvolts root-mean-square
Document Number: 001-12395 Rev. *F
Symbol
μW
mA
ms
mV
nA
ns
nV
W
pA
pF
pp
ppm
ps
sps
s
V
Unit of Measure
microwatts
milli-ampere
milli-second
milli-volts
nanoampere
nanosecond
nanovolts
ohm
picoampere
picofarad
peak-to-peak
parts per million
picosecond
samples per second
sigma: one standard deviation
volts
Page 14 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Electrical Characteristics
Absolute Maximum Ratings
Storage Temperature (TSTG) (3) ............................................. ...................................................... -55oC to 125oC (Typical +25oC)
Supply Voltage Relative to Vss (Vdd) .................................... ................................................................................. -0.5V to +4.0V
DC Input Voltage (VIO)........................................................... ................................................................. Vss - 0.5V to Vdd + 0.5V
DC Voltage Applied to Tri-state (VIOZ) ................................... ................................................................. Vss - 0.5V to Vdd + 0.5V
Maximum Current into any Port Pin (IMIO)............................. ............................................................................. -25mA to +50mA
Electro Static Discharge Voltage (ESD) (4) ............................ .............................................................................................. 2000V
Latch-up Current (LU) (5) ....................................................... ............................................................................................. 200mA
Operating Conditions
Ambient Temperature (TA) ..................................................... .....................................................................................0oC to 70oC
Operational Die Temperature (TJ)(6) ...................................... .....................................................................................0oC to 85oC
DC Electrical Characteristics
DC Chip Level Specifications
Table 7 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 7. DC Chip Level Specifications
Parameter
Description
Conditions
Min
Typ
Max
Units
1.71
–
3.6
V
Conditions are Vdd = 3.0V, TA = 25oC,
CPU = 24 MHz
No I2C/SPI
–
–
3.1
mA
Supply Current, IMO = 12 MHz
Conditions are Vdd = 3.0V, TA = 25oC,
CPU = 12 MHz
No I2C/SPI
–
–
2.0
mA
IDD6
Supply Current, IMO = 6 MHz
Conditions are Vdd = 3.0V, TA = 25oC,
CPU = 6 MHz
No I2C/SPI
–
–
1.5
mA
ISB0
Deep Sleep Current
Vdd = 3.0V, TA = 25oC, IO regulator
turned off
–
0.1
–
μA
ISB1
Standby Current with POR, LVD and
Sleep Timer
Vdd = 3.0V, TA = 25oC, IO regulator
turned off
–
–
1.5
μA
Vdd
Supply Voltage
See table titled DC POR and LVD
Specifications on page 19.
IDD24
Supply Current, IMO = 24 MHz
IDD12
Notes
3. Higher storage temperatures reduce data retention time. Recommended storage temperature is +25°C ± 25°C. Extended duration storage temperatures above 85°C
degrade reliability.
4. Human Body Model ESD.
5. Per JESD78 standard.
6. The temperature rise from ambient to junction is package specific. See Package Diagram on page 24 for Thermal Impedances. The user must limit the power
consumption to comply with this requirement.
Document Number: 001-12395 Rev. *F
Page 15 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
DC General Purpose IO Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 1.71V to 3.6V and
0°C ≤ TA ≤ 70°C. Typical parameters apply to 3.3V at 25°C. These are for design guidance only.
Table 8. 3.0V to 3.6V DC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
4
5.6
8
kΩ
IOH < 10 μA, maximum of 10 mA
source current in all IOs
Vdd - 0.2
–
–
V
High Output Voltage
Port 2 or 3 Pins
IOH = 1 mA, maximum of 20 mA
source current in all IOs
Vdd - 0.9
–
–
V
VOH3
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH < 10 μA, maximum of 10 mA
source current in all IOs
Vdd - 0.2
–
–
V
VOH4
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 5 mA, maximum of 20 mA
source current in all IOs
Vdd - 0.9
–
–
V
VOH5
High Output Voltage
Port 1 Pins with LDO Regulator
Enabled for 3V Out
IOH < 10 μA, Vdd > 3.1V, maximum of
4 IOs all sourcing 5 mA
2.85
3.00
3.15
V
VOH6
High Output Voltage
Port 1 Pins with LDO Regulator
Enabled for 3V Out
IOH = 5 mA, Vdd > 3.1V, maximum of
20 mA source current in all IOs
2.20
–
–
V
VOH7
High Output Voltage
IOH < 10 μA, Vdd > 2.7V, maximum of
Port 1 Pins with LDO Enabled for 2.5V 20 mA source current in all IOs
Out
2.35
2.50
2.65
V
VOH8
High Output Voltage
IOH = 2 mA, Vdd > 2.7V, maximum of
Port 1 Pins with LDO Enabled for 2.5V 20 mA source current in all IOs
Out
1.90
–
–
V
VOH9
IOH < 10 μA, Vdd > 2.7V, maximum of
High Output Voltage
Port 1 Pins with LDO Enabled for 1.8V 20 mA source current in all IOs
Out
1.60
1.80
2.00
V
VOH10
High Output Voltage
IOH = 1 mA, Vdd > 2.7V, maximum of
Port 1 Pins with LDO Enabled for 1.8V 20 mA source current in all IOs
Out
1.20
–
–
V
VOL
Low Output Voltage
–
–
0.75
V
VIL
Input Low Voltage
–
–
0.80
V
VIH
Input High Voltage
2.00
–
VH
Input Hysteresis Voltage
–
80
–
mV
IIL
Input Leakage (Absolute Value)
Gross tested to 1 µA.
–
1
-
nA
CIN
Capacitive Load on Pins as Input
Package and pin dependent
Temp = 25oC
0.5
1.7
5
pF
COUT
Capacitive Load on Pins as Output
Package and pin dependent
Temp = 25oC
0.5
1.7
5
pF
RPU
Pull up Resistor
VOH1
High Output Voltage
Port 2 or 3 Pins
VOH2
Document Number: 001-12395 Rev. *F
Conditions
IOL = 25 mA, Vdd > 3.3V, maximum of
60 mA sink current on even port pins
(for example, P0[2] and P1[4]) and 60
mA sink current on odd port pins (for
example, P0[3] and P1[5])
V
Page 16 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 9. 2.4V to 3.0V DC GPIO Specifications
Symbol
RPU
VOH1
VOL
Description
Pull up Resistor
High Output Voltage
Port 2 or 3 Pins
High Output Voltage
Port 2 or 3 Pins
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
High Output Voltage
Port 1 Pins with LDO Enabled for 1.8V
Out
High Output Voltage
Port 1 Pins with LDO Enabled for 1.8V
Out
Low Output Voltage
VIL
VIH
VH
IIL
CIN
Input Low Voltage
Input High Voltage
Input Hysteresis Voltage
Input Leakage (Absolute Value)
Capacitive Load on Pins as Input
COUT
Capacitive Load on Pins as Output
VOH2
VOH3
VOH4
VOH5A
VOH6A
Document Number: 001-12395 Rev. *F
Conditions
Min
4
Vdd - 0.2
Typ
5.6
–
Max
8
–
Units
kΩ
V
Vdd - 0.4
–
–
V
Vdd - 0.2
–
–
V
Vdd - 0.5
–
–
V
IOH < 10 μA, Vdd > 2.4V, maximum
of 20 mA source current in all IOs.
1.50
1.80
2.00
V
IOH = 1 mA, Vdd > 2.4V, maximum of
20 mA source current in all IOs
1.20
–
–
V
IOL = 10 mA, maximum of 30 mA sink
current on even port pins (for
example, P0[2] and P1[4]) and 30 mA
sink current on odd port pins (for
example, P0[3] and P1[5])
–
–
0.75
V
–
2.0
–
–
0.5
–
–
80
1
1.7
0.72
–
–
5
V
V
mV
nA
pF
0.5
1.7
5
pF
IOH < 10 μA, maximum of 10 mA
source current in all IOs
IOH = 0.2 mA, maximum of 10 mA
source current in all IOs
IOH < 10 μA, maximum of 10 mA
source current in all IOs
IOH = 2 mA, maximum of 10 mA
source current in all IOs
Gross tested to 1 µA.
Package and pin dependent
Temp = 25oC
Package and pin dependent
Temp = 25oC
Page 17 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Table 10. 1.71V to 2.4V DC GPIO Specifications
Symbol
Description
Min
Typ
Max
Units
4
5.6
8
kΩ
IOH = 10 μA, maximum of 10 mA
source current in all IOs
Vdd - 0.2
–
–
V
High Output Voltage
Port 2 or 3 Pins
IOH = 0.5 mA, maximum of 10 mA
source current in all IOs
Vdd - 0.5
–
–
V
VOH3
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 100 μA, maximum of 10 mA
source current in all IOs
Vdd - 0.2
–
–
V
VOH4
High Output Voltage
Port 0 or 1 Pins with LDO Regulator
Disabled for Port 1
IOH = 2 mA, maximum of 10 mA
source current in all IOs
Vdd - 0.5
–
–
V
VOL
Low Output Voltage
IOL = 5 mA, maximum of 20 mA sink
current on even port pins (for
example, P0[2] and P1[4]) and 30 mA
sink current on odd port pins (for
example, P0[3] and P1[5])
–
–
0.4
V
VIL
Input Low Voltage
–
–
0.3 x Vdd
V
VIH
Input High Voltage
0.65 x Vdd
–
VH
Input Hysteresis Voltage
–
80
–
mV
IIL
Input Leakage (Absolute Value)
Gross tested to 1 µA.
–
1
–
nA
CIN
Capacitive Load on Pins as Input
Package and pin dependent.
Temp = 25oC
0.5
5
pF
COUT
Capacitive Load on Pins as Output
Package and pin dependent
Temp = 25oC
0.5
5
pF
RPU
Pull up Resistor
VOH1
High Output Voltage
Port 2 or 3 Pins
VOH2
Document Number: 001-12395 Rev. *F
Conditions
V
Page 18 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
DC POR and LVD Specifications
Table 11 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 11. DC POR and LVD Specifications
Symbol
Description
Min
Typ
Max
Units
1.61
1.66
2.36
2.60
2.82
1.71
2.40
2.65
2.95
V
V
V
V
2.40
2.64
2.85
2.95
3.06
–
–
2.45
2.71
2.92
3.02
3.13
1.9
1.8
2.51
2.78
2.99
3.09
3.20
–
–
V
V
V
V
(7)
VPPOR0
VPPOR1
VPPOR2
VPPOR3
Vdd Value for PPOR Trip
PORLEV[1:0] = 00b, HPOR = 0
PORLEV[1:0] = 00b, HPOR = 1
PORLEV[1:0] = 01b, HPOR = 1
PORLEV[1:0] = 10b, HPOR = 1
VLVD0
VLVD1
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
Vdd Value for LVD Trip
VM[2:0] = 000b(8)
VM[2:0] = 001b(9)
VM[2:0] = 010b(10)
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b(11)
DC Programming Specifications
Table 12 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 12. DC Programming Specifications
Symbol
VddIWRITE
IDDP
VILP
VIHP
IILP
IIHP
VOLV
VOHV
FlashENPB
FlashDR
Description
Supply Voltage for Flash Write Operations
Supply Current During Programming or Verify
Input Low Voltage During Programming or Verify
Input High Voltage During Programming or Verify
Input Current when Applying Vilp to P1[0] or P1[1]
During Programming or Verify(12)
Input Current when Applying Vihp to P1[0] or P1[1]
During Programming or Verify(13)
Output Low Voltage During Programming or Verify
Output High Voltage During Programming or Verify
Flash Write Endurance(14)
Flash Data Retention(15)
Min
1.71
–
–
VIH
–
Typ
–
5
–
–
–
Max
–
25
VIL
–
0.2
Units
V
mA
V
V
mA
–
–
1.5
mA
–
Vdd - 1.0
50,000
10
–
–
–
20
Vss + 0.75
Vdd
–
–
V
V
Cycles
Years
Notes
7. Vdd must be greater than or equal to 1.71V during startup, reset from the XRES pin, or reset from watchdog.
8. Always greater than 50 mV above VPPOR1 for falling supply.
9. Always greater than 50 mV above VPPOR2 for falling supply.
10. Always greater than 50 mV above VPPOR3 for falling supply.
11. Always greater than 50 mV above VPPOR0 voltage for falling supply.
12. Driving internal pull down resistor.
13. Driving internal pull down resistor.
14. Erase/write cycles per block.
15. Following maximum Flash write cycles.
Document Number: 001-12395 Rev. *F
Page 19 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
AC Electrical Characteristics
AC Chip Level Specifications
Table 13 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 13. AC Chip Level Specifications
Symbol
FMAX
FCPU
F32K1
FIMO24
FIMO12
FIMO6
DCIMO
TRAMP
Description
Maximum Operating Frequency(16)
Maximum Processing Frequency(17)
Internal Low Speed Oscillator Frequency
Internal Main Oscillator Stability for 24 MHz ± 5%(18)
Internal Main Oscillator Stability for 12 MHz(19)
Internal Main Oscillator Stability for 6 MHz(20)
Duty Cycle of IMO
Supply Ramp Time
Min
24
24
30.4
22.8
11.4
5.7
40
0
Typ
–
–
32
24
12
6.0
50
–
Max
–
–
33.6
25.2
12.6
6.3
60
–
Units
MHz
MHz
kHz
MHz
MHz
MHz
%
μs
Notes
16. Digital clocking functions.
17. CPU speed.
18. Trimmed using factory trim values.
19. Trimmed using factory trim values.
20. Trimmed using factory trim values.
Document Number: 001-12395 Rev. *F
Page 20 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
AC General Purpose IO Specifications
Table 14 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 14. AC GPIO Specifications
Symbol
FGPIO
Description
GPIO Operating Frequency
Conditions
Min
Typ
Max
Units
Normal Strong Mode, Port 0, 1
0
–
3 MHz for
1.71V<Vdd<2.4V
MHz
0
–
6 MHz for
2.4V<Vdd<3.0V
0
–
12 MHz for
3.0V<Vdd<3.6V
0
–
3 MHz for
1.71V<Vdd<2.4V
0
–
6 MHz for
2.4V<Vdd<3.0V
0
–
6 MHz for
3.0V<Vdd<3.6V
15
–
80
Normal Strong Mode, Port 2, 3
TRise023
Rise Time, Strong Mode, Cload = 50 pF
Ports 2 or 3
Vdd = 3.0 to 3.6V, 10% – 90%
MHz
ns
Vdd = 2.4 to 3.0V, 10% – 90%
15
–
100
TRise023L Rise Time, Strong Mode Low Supply,
Cload = 50 pF
Ports 2 or 3
Vdd = 1.71 to 3.0V, 10% – 90%
15
–
100
ns
TRise1
Vdd = 3.0 to 3.6V, 10% – 90%
LDO enabled or disabled
10
–
50
ns
Vdd = 2.4 to 3.0V, 10% – 90%
LDO enabled or disabled
10
–
70
Rise Time, Strong Mode, Cload = 50 pF
Ports 0 or 1
TRise1L
Rise Time, Strong Mode Low Supply,
Cload = 50 pF
Ports 0 or 1
Vdd = 1.71 to 3.0V, 10% – 90%
LDO enabled or disabled
15
–
100
ns
TFall
Fall Time, Strong Mode, Cload = 50 pF
All Ports
Vdd = 3.0 to 3.6V, 10% – 90%
10
–
80
ns
Vdd = 2.4 to 3.0V, 10% - 90%
10
–
80
Document Number: 001-12395 Rev. *F
Page 21 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Figure 7. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TFall
TRise023
TRise1
AC External Clock Specifications
Table 15 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 15. AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
FOSCEXT
Frequency
0.750
–
25.2
MHz
–
High Period
20.6
–
5300
ns
–
Low Period
20.6
–
–
ns
–
Power Up IMO to Switch
150
–
–
μs
AC Programming Specifications
Table 16 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 16. AC Programming Specifications
Symbol
TRSCLK
TFSCLK
TSSCLK
THSCLK
FSCLK
TERASEB
TWRITE
TDSCLK
TDSCLK3
TDSCLK2
Description
Rise Time of SCLK
Fall Time of SCLK
Data Set up Time to Falling Edge of SCLK
Data Hold Time from Falling Edge of SCLK
Frequency of SCLK
Flash Erase Time (Block)
Flash Block Write Time
Data Out Delay from Falling Edge of SCLK
Data Out Delay from Falling Edge of SCLK
Data Out Delay from Falling Edge of SCLK
Document Number: 001-12395 Rev. *F
Min
1
1
40
40
0
–
–
–
–
–
Typ
–
–
–
–
–
–
–
–
–
–
Max
20
20
–
–
8
18
25
45
50
70
Units
ns
ns
ns
ns
MHz
ms
ms
ns
ns
ns
Page 22 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
AC SPI Specifications
Table 17 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 17. AC SPI Specifications
Symbol
Description
(21)
Min
Typ
Max
Units
FSPIM
Maximum Input Clock Frequency Selection, Master
–
–
8.2
MHz
FSPIS
Maximum Input Clock Frequency Selection, Slave
–
–
4.1
MHz
TSS
Width of SS_ Negated Between Transmissions
50
–
–
ns
AC I2C Specifications
Table 18 lists guaranteed maximum and minimum specifications for the entire voltage and temperature ranges.
Table 18. AC Characteristics of the I2C SDA and SCL Pins
Symbol
FSCLI2C
THDSTAI2C
TLOWI2C
THIGHI2C
TSUSTAI2C
THDDATI2C
TSUDATI2C
TSUSTOI2C
TBUFI2C
TSPI2C
Description
SCL Clock Frequency
Hold Time (repeated) START Condition. After this
period, the first clock pulse is generated.
LOW Period of the SCL Clock
HIGH Period of the SCL Clock
Set-up Time for a Repeated START Condition
Data Hold Time
Data Set-up Time
Set-up Time for STOP Condition
Bus Free Time Between a STOP and START Condition
Pulse Width of spikes are suppressed by the input filter
Standard Mode
Min
Max
0
100
4.0
–
4.7
4.0
4.7
0
250
4.0
4.7
–
–
–
–
–
–
–
–
–
Fast Mode
Min
Max
0
400
0.6
–
1.3
0.6
0.6
0
100(22)
0.6
1.3
0
Units
kHz
μs
μs
μs
μs
μs
ns
μs
μs
ns
–
–
–
–
–
–
–
50
Figure 8. Definition for Timing for Fast/Standard Mode on the I2C Bus
SDA
TLOWI2C
TSUDATI2C
THDSTAI2C
TSPI2C
TBUFI2C
SCL
S THDSTAI2C THDDATI2C THIGHI2C
TSUSTAI2C
Sr
TSUSTOI2C
P
S
Notes
21. Output clock frequency is half of input clock rate.
22. A fast mode I2C bus device can be used in a standard mode I2C bus system, but the requirement tSU;DAT Š 250 ns must then be met. This is automatically the case
if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the
SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the standard mode I2C bus specification) before the SCL line is released.
Document Number: 001-12395 Rev. *F
Page 23 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Package Diagram
This chapter illustrates the packaging specifications for the enCoRe V LV device, along with the thermal impedances for each package.
Important Note Emulation tools may require a larger area on the target PCB than the chip’s footprint. For a detailed description of
the enCoRe V LV emulation tools and their dimensions, refer to the development kit.
Packaging Dimensions
Figure 9. 32-Lead (5x5 x 0.6 mm) QFN
001-06352 *B
Document Number: 001-12395 Rev. *F
Page 24 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Figure 10. 48-Lead (7x7 x 1mm) QFN
001-13191 **
Document Number: 001-12395 Rev. *F
Page 25 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Thermal Impedances
Table 19. Thermal Impedances per Package
Typical θJA *
14.5 oC/W
28 oC/W
Package
32 QFN**
48 QFN**
* TJ = TA + Power x θJA
** To achieve the thermal impedance specified for the ** package, solder the
center thermal pad to the PCB ground plane.
Solder Reflow Peak Temperature
Following is the minimum solder reflow peak temperature to achieve good solderability.
Table 20. Solder Reflow Peak Temperature
Package
Minimum Peak Temperature*
Maximum Peak Temperature
32 QFN
240oC
260oC
48 QFN
240oC
260oC
*Higher temperatures may be required based on the solder melting point. Typical temperatures for solder are 220 ± 5oC with Sn-Pb or 245 ± 5oC with Sn-Ag-Cu
paste. Refer to the solder manufacturer specifications.
Ordering Information
Ordering Code
Flash
SRAM
No. of GPIOs
16K
1K
28
Feature-Rich Wireless
Mouse
CY7C60445-32LQXCT 32-lead QFN - (Tape
and Reel)
(5x5x0.6mm)
16K
1K
28
Feature-Rich Wireless
Mouse
CY7C60455-48LTXC
48-lead QFN
(7x7x1mm)
16K
1K
36
Mid-Tier Wireless Keyboard
CY7C60455-48LTXCT
48-lead QFN - (Tape
and Reel)
(7x7x1mm)
16K
1K
36
Mid-Tier Wireless Keyboard
CY7C60456-48LTXC
48-lead QFN
(7x7x1mm)
32K
2K
36
Feature-Rich Wireless
Keyboard
CY7C60456-48LTXCT
48-lead QFN - (Tape
and Reel)
(7x7x1mm)
32K
2K
36
Feature-Rich Wireless
Keyboard
CY7C60445-32LQXC
Package Information
32-lead QFN
(5x5x0.6mm)
Document Number: 001-12395 Rev. *F
Target Applications
Page 26 of 27
[+] Feedback
PRELIMINARY
CY7C60445, CY7C6045x
Document History Page
Document Title: CY7C60445, CY7C6045x, enCoRe™ V Low Voltage Microcontroller
Document Number: 001-12395
REV.
ECN.
Issue Date
Orig. of
Change
**
626516
See ECN
TYJ
*A
735721
See ECN
TYJ/ARI
*B
1120504
See ECN
ARI
*C
1225864
See ECN
*D
1446763
See ECN
AESA
Changed TERASEB parameter, max value to 18ms in Table 13, AC Programming
Specification.
*E
1639963
See ECN
AESA
Post to www.cypress.com
*F
2138889
See ECN
Description of Change
New data sheet
Added new block diagram, replaced TBDs, corrected values, updated pinout
information, changed part number to reflect new specifications.
Corrected the description to pin 29 on Table 1, the Typ/Max values for ISB0 on
the DC chip-level specifications, and the Min voltage value for VddIWRITE in the
DC Programming Specifications table.
Corrected Flash Write Endurance minimum value in the DC Programming Specifications table.
Corrected the Flash Erase Time max value and the Flash Block Write Time max
value in the AC Programming Specifications table.
Implemented new latest template.
AESA/ARI Corrected the description to pin 13, 29 on Table 1 and 22,44 on Table 2.
Added sections Register Reference, Register Conventions and Register
Mapping Tables. Corrected Max values on the DC Chip-Level Specifications
table.
TYJ/PYRS Updated Ordering Code table:
- Ordering code changed for 32-QFN package: From -32LKXC to -32LTXC
- Added a new package type – “LTXC” for 48-QFN
- Included Tape and Reel ordering code for 32-QFN and 48-QFN packages
Changed active current values at 24, 12 and 6MHz in table “DC Chip-Level Specifications”
- IDD24: 2.15 to 3.1mA
- IDD12: 1.45 to 2.0mA
- IDD6: 1.1 to 1.5mA
Added information on using P1[0] and P1[1] as the I2C interface during POR or
reset events
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-12395 Rev. *F
Revised March 19, 2008
Page 27 of 27
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback