CYPRESS CY8C29466

CY8C29466, CY8C29566
CY8C29666, CY8C29866
PSoC® Programmable System-on-Chip™
PSoC® Programmable System-on-Chip
Features
■
■
■
■
■
Powerful Harvard-architecture processor
❐ M8C processor speeds to 24 MHz
❐ Two 8 × 8 multiply, 32-bit accumulate
❐ Low power at high speed
❐ Operating voltage: 3.0 V to 5.25 V
❐ Operating voltages down to 1.0 V using on-chip switch mode
pump (SMP)
❐ Industrial temperature range: –40 °C to +85 °C
■
Additional system resources
2
❐ I C slave, master, and multi-master to 400 kHz
❐ Watchdog and sleep timers
❐ User-configurable low-voltage detection (LVD)
❐ Integrated supervisory circuit
❐ On-chip precision voltage reference
■
Complete development tools
❐ Free development software (PSoC Designer™)
❐ Full-featured in-circuit emulator (ICE) and
programmer
❐ Full-speed emulation
❐ Complex breakpoint structure
❐ 128 KB trace memory
❐ Complex events
❐ C compilers, assembler, and linker
Advanced peripherals (PSoC® blocks)
❐ 12 rail-to-rail analog PSoC blocks provide:
• Up to 14-bit analog-to-digital converters (ADCs)
• Up to 9-bit digital-to-analog converters (DACs)
• Programmable gain amplifiers (PGAs)
• Programmable filters and comparators
❐ 16 digital PSoC blocks provide:
• 8- to 32-bit timers, counters, and pulse-width modulators
(PWMs)
• Cyclical redundancy check (CRC) and pseudo random
sequence (PRS) modules
• Up to four full-duplex universal asynchronous receiver
transmitters (UARTs)
• Multiple serial peripheral interface (SPI) masters or slaves
• Can connect to all general-purpose I/O (GPIO) pins
❐ Create complex peripherals by combining blocks
Logic Block Diagram
Port
7
Port
5
Port
4
Port
3
Port
2
Port
1
Port 0 with
Analog Drivers
PSoC
CORE
System Bus
Global Digital Interconnect
Precision, programmable clocking
❐ Internal ±2.5% 24- / 48-MHz main oscillator
❐ 24- / 48-MHz with optional 32.768 kHz crystal
❐ Optional external oscillator, up to 24 MHz
❐ Internal oscillator for watchdog and sleep
SRAM
2 KB
Global Analog Interconnect
SROM
Flash 32KB
CPU Core (M8C)
Interrupt
Controller
Flexible on-chip memory
❐ 32 KB flash program storage 50,000 erase/write cycles
❐ 2 KB static random access memory (SRAM) data storage
❐ In-system serial programming (ISSP)
❐ Partial flash updates
❐ Flexible protection modes
❐ Electrically erasable programmable read-only memory
(EEPROM) emulation in flash
Programmable pin configurations
❐ 25-mA sink, 10-mA source on all GPIOs
❐ Pull-up, pull-down, high Z, strong, or open-drain drive modes
on all GPIOs
❐ Eight standard analog inputs on GPIOs, plus four additional
analog inputs with restricted routing
❐ Four 40 mA analog outputs on GPIOs
❐ Configurable interrupt on all GPIOs
Port
6
Sleep and
Watchdog
Multiple Clock Sources
(Includes IMO, ILO, PLL, and ECO)
DIGITAL SYSTEM
ANALOG SYSTEM
Analog
Ref.
Digital
Block
Array
Digital
Clocks
Multiply
Accum.
Analog
Block
Array
Analog
Input
Muxing
POR and LVD
Decimator
I2 C
System Resets
Internal
Voltage
Ref.
Switch
Mode
Pump
SYSTEM RESOURCES
Cypress Semiconductor Corporation
Document Number: 38-12013 Rev. *S
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised July 7, 2011
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Contents
PSoC Programmable System-on-Chip ........................... 1
Features ............................................................................. 1
Logic Block Diagram ........................................................ 1
PSoC Functional Overview .............................................. 3
PSoC Core .................................................................. 3
Digital System ............................................................. 3
Analog System ............................................................ 4
Additional System Resources ..................................... 5
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 6
Application Notes ........................................................ 6
Development Kits ........................................................ 6
Training ....................................................................... 6
CYPros Consultants .................................................... 6
Solutions Library .......................................................... 6
Technical Support ....................................................... 6
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
Designing with PSoC Designer ....................................... 7
Select User Modules ................................................... 7
Configure User Modules .............................................. 7
Organize and Connect ................................................ 7
Generate, Verify, and Debug ....................................... 7
Pinouts .............................................................................. 8
28-Pin Part Pinout ....................................................... 8
44-Pin Part Pinout ....................................................... 9
48-Pin Part Pinout ..................................................... 10
100-Pin Part Pinout ................................................... 12
100-Pin Part Pinout (On-Chip Debug) ....................... 14
Register Reference ......................................................... 16
Register Conventions ................................................ 16
Register Mapping Tables .......................................... 16
Document Number: 38-12013 Rev. *S
Electrical Specifications ................................................ 19
Absolute Maximum Ratings ....................................... 19
Operating Temperature ............................................ 20
DC Electrical Characteristics ..................................... 20
AC Electrical Characteristics ..................................... 35
Packaging Information ................................................... 44
Packaging Dimensions .............................................. 44
Thermal Impedances ................................................ 49
Capacitance on Crystal Pins .................................... 49
Solder Reflow Specifications ..................................... 49
Development Tool Selection ......................................... 50
Software .................................................................... 50
Development Kits ...................................................... 50
Evaluation Tools ........................................................ 50
Device Programmers ................................................. 51
Accessories (Emulation and Programming) ................ 51
Ordering Information ...................................................... 52
Ordering Code Definitions ......................................... 52
Acronyms ........................................................................ 53
Acronyms Used ......................................................... 53
Reference Documents .................................................... 53
Document Conventions ............................................. 54
Units of Measure ....................................................... 54
Numeric Conventions ................................................ 54
Glossary .......................................................................... 54
Document History Page ................................................ 59
Sales, Solutions, and Legal Information ...................... 61
Worldwide Sales and Design Support ....................... 61
Products .................................................................... 61
PSoC Solutions ......................................................... 61
Page 2 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
PSoC Functional Overview
The PSoC family consists of many Programmable
System-on-Chip controller devices. These devices are designed
to replace multiple traditional microcontroller unit (MCU)-based
system components with one, low-cost single-chip programmable device. PSoC devices include configurable blocks of
analog and digital logic, as well as programmable interconnects.
This architecture allows you to create customized peripheral
configurations that match the requirements of each individual
application. Additionally, a fast central processing unit (CPU),
flash program memory, SRAM data memory, and configurable
I/O are included in a range of convenient pinouts and packages.
The PSoC architecture, as illustrated in the Logic Block Diagram
on page 1, consists of four main areas: PSoC core, digital
system, analog system, and system resources. Configurable
global busing allows all of the device resources to be combined
into a complete custom system. The PSoC CY8C29x66 family
can have up to five I/O ports that connect to the global digital and
analog interconnects, providing access to 8 digital blocks and
12 analog blocks.
selected from eight options, allowing great flexibility in external
interfacing. Every pin also has the capability to generate a
system interrupt on high level, low level, and change from last
read.
Digital System
The digital system is composed of 16 digital PSoC blocks. Each
block is an 8-bit resource that can be used alone or combined
with other blocks to form 8-, 16-, 24-, and 32-bit peripherals,
which are called user modules.
Figure 1. Digital System Block Diagram
Port7
Port5
Port6
Port3
Port4
To System Bus
Digital Clocks
From Core
Port1
Port2
Port0
To Analog
System
PSoC Core
DIGITAL SYSTEM
The PSoC core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
GPIOs.
Row Input
Configuration
DBB01
DCB02
DCB03
4
8
8
Row1
DBB10
DBB11
DCB12
4
DCB13
4
Row2
DBB20
DBB21
DCB22
4
DCB23
4
Row3
DBB30
DBB31
DCB32
4
DCB33
4
GIE[7:0]
GIO[7:0]
Global Digital
Interconnect
8
Row Output
Configuration
Row Input
Configuration
Row Input
Configuration
Row Input
Configuration
8
Row Output
Configuration
The PSoC device incorporates flexible internal clock generators,
including a 24 MHz internal main oscillator (IMO) accurate to
2.5% over temperature and voltage. The 24 MHz IMO can also
be doubled to 48 MHz for use by the digital system. A low-power
32 kHz internal low speed oscillator (ILO) is provided for the
sleep timer and WDT. If crystal accuracy is desired, the
32.768 kHz external crystal oscillator (ECO) is available for use
as a real-time clock (RTC) and can optionally generate a
crystal-accurate 24 MHz system clock using a PLL. The clocks,
together with programmable clock dividers (as a system
resource), provide the flexibility to integrate almost any timing
requirement into the PSoC device.
DBB00
4
Row Output
Configuration
Memory uses 16 KB of flash for program storage, 256 bytes of
SRAM for data storage, and up to 2 KB of EEPROM emulated
using the flash. Program flash uses four protection levels on
blocks of 64 bytes, allowing customized software information
protection (IP).
Row0
Row Output
Configuration
The M8C CPU core is a powerful processor with speeds up to
24 MHz, providing a 4 million instructions per second (MIPS)
8-bit Harvard-architecture microprocessor. The CPU uses an
interrupt controller with 17 vectors, to simplify programming of
real-time embedded events. Program execution is timed and
protected using the included sleep and watchdog timers (WDT).
Digital PSoC Block Array
GOE[7:0]
GOO[7:0]
PSoC GPIOs provide connection to the CPU, and digital and
analog resources of the device. Each pin’s drive mode may be
Document Number: 38-12013 Rev. *S
Page 3 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Digital peripheral configurations include:
■
DTMF Dialer
■
PWMs (8- to 32-bit)
■
Modulators
■
PWMs with dead band (8- to 32-bit)
■
Correlators
■
Counters (8- to 32-bit)
■
Peak detectors
■
Timers (8- to 32-bit)
■
Many other topologies possible
■
UART 8-bit with selectable parity (up to 2)
■
SPI slave and master (up to 2)
Analog blocks are provided in columns of three, which includes
one continuous time (CT) and two switched capacitor (SC)
blocks, as shown in Figure 2.
■
I2C slave and multi-master (one available as a system
resource)
■
CRC generator (8- to 32-bit)
■
IrDA (up to 2)
■
PRS generators (8- to 32-bit)
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This allows you the
optimum choice of system resources for your application. Family
resources are shown in the table titled “PSoC Device
Characteristics” on page 5.
P0[7]
P0[6]
P0[5]
P0[4]
P0[3]
P0[2]
P0[1]
P0[0]
AGNDIn RefIn
The digital blocks can be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow for signal multiplexing and for performing logic
operations. This configurability frees your designs from the
constraints of a fixed peripheral controller.
Figure 2. Analog System Block Diagram
P2[3]
P2[1]
■
ADCs (up to 4, with 6- to 14-bit resolution; selectable as
incremental, delta sigma, and SAR)
■
Filters (2-, 4-, 6-, and 8-pole band pass, low pass, and notch)
■
Amplifiers (up to 4, with selectable gain to 48x)
■
Instrumentation amplifiers (up to 2, with selectable gain to 93x)
■
Comparators (up to 4, with 16 selectable thresholds)
■
DACs (up to 4, with 6-bit to 9-bit resolution)
■
Multiplying DACs (up to 4, with 6-bit to 9-bit resolution)
■
High current output drivers (four with 30-mA drive as a core
resource)
■
P2[4]
P2[2]
P2[0]
Analog System
The analog system is composed of 12 configurable blocks, each
containing an opamp circuit that allows the creation of complex
analog signal flows. Analog peripherals are very flexible and can
be customized to support specific application requirements.
Some of the more common PSoC analog functions (most
available as user modules) are:
P2[6]
Array Input Configuration
ACI0[1:0]
ACI1[1:0]
ACI2[1:0]
ACI3[1:0]
Block Array
ACB00
ACB01
ACB02
ACB03
ASC10
ASD11
ASC12
ASD13
ASD20
ASC21
ASD22
ASC23
Analog Reference
Interface to
Digital System
RefHi
RefLo
AGND
Reference
Generators
AGNDIn
RefIn
Bandgap
M8C Interface (Address Bus, Data Bus, Etc.)
1.3-V reference (as a system resource)
Document Number: 38-12013 Rev. *S
Page 4 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Additional System Resources
System resources, some of which were previously listed, provide
additional capability useful to complete systems. Additional
resources include a multiplier, decimator, switch mode pump,
low-voltage detection, and power-on-reset (POR).
■
■
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks can be routed
to both the digital and analog systems. Additional clocks can
be generated using digital PSoC blocks as clock dividers.
Multiply accumulate (MAC) provides a fast 8-bit multiplier with
32-bit accumulate, to assist in general math and digital filters.
The decimator provides a custom hardware filter for digital
signal processing applications including the creation of delta
sigma ADCs.
The I2C module provides 100 and 400 kHz communication over
two wires. Slave, master, and multi-master modes are all
supported.
■ LVD interrupts can signal the application of falling voltage
levels, while the advanced POR circuit eliminates the need for
a system supervisor.
■ An internal 1.3 V reference provides an absolute reference for
the analog system, including ADCs and DACs.
■ An integrated switch-mode pump (SMP) generates normal
operating voltages from a single 1.2 V battery cell, providing a
low cost boost converter.
■
PSoC Device Characteristics
Depending on your PSoC device characteristics, the digital and analog systems can have 16, 8, or 4 digital blocks and 12, 6, or 4
analog blocks. The following table lists the resources available for specific PSoC device groups.The PSoC device covered by this
datasheet is highlighted.
Table 1. PSoC Device Characteristics
PSoC Part
Number
Digital
I/O
Digital
Rows
Digital
Blocks
Analog
Inputs
Analog
Outputs
Analog
Columns
Analog
Blocks
SRAM
Size
Flash
Size
CY8C29x66
up to 64
4
16
up to 12
4
4
12
2K
32 K
CY8C28xxx
up to 44
up to 3
up to 12
up to 44
up to 4
up to 6
up to
12 + 4[1]
1K
16 K
CY8C27x43
up to 44
2
8
up to 12
4
4
12
256
16 K
16 K
CY8C24x94
up to 56
1
4
up to 48
2
2
6
1K
CY8C24x23A
up to 24
1
4
up to 12
2
2
6
256
4K
CY8C23x33
up to 26
1
4
up to 12
2
2
4
256
8K
CY8C22x45
up to 38
2
8
up to 38
0
4
6[1]
1K
16 K
CY8C21x45
up to 24
1
4
up to 24
0
4
6[1]
512
8K
[1]
CY8C21x34
up to 28
1
4
up to 28
0
2
4
512
8K
CY8C21x23
up to 16
1
4
up to 8
0
2
4[1]
256
4K
CY8C20x34
up to 28
0
0
up to 28
0
0
3[1,2]
512
8K
0
3[1,2]
up to 2 K
up to 32 K
CY8C20xx6
up to 36
0
0
up to 36
0
Notes
1. Limited analog functionality.
2. Two analog blocks and one CapSense®.
Document Number: 38-12013 Rev. *S
Page 5 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Getting Started
For in depth information, along with detailed programming
details, see the PSoC® Technical Reference Manual.
CYPros Consultants
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web.
Certified PSoC Consultants offer everything from technical
assistance to completed PSoC designs. To contact or become a
PSoC Consultant go to the CYPros Consultants web site.
Application Notes
Solutions Library
Cypress application notes are an excellent introduction to the
wide variety of possible PSoC designs.
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
Development Kits
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Training
Technical Support
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
Development Tools
PSoC Designer™ is the revolutionary Integrated Design
Environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
■
Integrated source-code editor (C and assembly)
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
■
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up to four full-duplex universal asynchronous receiver/transmitters (UARTs), SPI master and slave, and wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
Document Number: 38-12013 Rev. *S
PSoC Designer Software Subsystems
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are analog-to-digital converters (ADCs),
digital-to-analog converters (DACs), amplifiers, and filters.
Configure the user modules for your chosen application and
connect them to each other and to the proper pins. Then
generate your project. This prepopulates your project with APIs
and libraries that you can use to program your application.
The tool also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic reconfiguration
makes it possible to change configurations at run time. In
essence, this allows you to use more than 100 percent of PSoC's
resources for an application.
Code Generation Tools
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
Page 6 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Debugger
In-Circuit Emulator
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also allows you to create a trace buffer of registers and memory
locations of interest.
A low-cost, high-functionality In-Circuit Emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24 MHz) operation.
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer.
Designing with PSoC Designer
The development process for the PSoC® device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
The PSoC development process is summarized in four steps:
1. Select User Modules.
2. Configure user modules.
3. Organize and connect.
4. Generate, verify, and debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules.” User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
configuration to your particular application. For example, a pulse
width modulator (PWM) User Module configures one or more
digital PSoC blocks, one for each 8 bits of resolution. The user
module parameters permit you to establish the pulse width and
duty cycle. Configure the parameters and properties to correspond to your chosen application. Enter values directly or by
selecting values from drop-down menus. All the user modules
are documented in datasheets that may be viewed directly in
PSoC Designer or on the Cypress website. These user module
datasheets explain the internal operation of the user module and
provide performance specifications. Each datasheet describes
the use of each user module parameter, and other information
you may need to successfully implement your design.
Document Number: 38-12013 Rev. *S
Organize and Connect
You build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. You perform the
selection, configuration, and routing so that you have complete
control over all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, you perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides application programming interfaces
(APIs) with high-level functions to control and respond to
hardware events at run time and interrupt service routines that
you can adapt as needed.
A complete code development environment allows you to
develop and customize your applications in either C, assembly
language, or both.
The last step in the development process takes place inside
PSoC Designer’s debugger (access by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full speed. PSoC Designer debugging capabilities rival those of systems costing many times more. In addition
to traditional single-step, run-to-breakpoint and watch-variable
features, the debug interface provides a large trace buffer and
allows you to define complex breakpoint events that include
monitoring address and data bus values, memory locations and
external signals.
Page 7 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Pinouts
The CY8C29x66 PSoC device is available in a variety of packages which are listed and illustrated in the following tables. Every port
pin (labeled with a “P”) is capable of Digital I/O. However, VSS, VDD, SMP, and XRES are not capable of Digital I/O.
28-Pin Part Pinout
Table 2. 28-Pin Part Pinout (PDIP, SSOP, SOIC)
Pin
No.
Type
Digital
Analog
Pin
Name
Description
1
I/O
I
P0[7]
Analog column mux input
2
I/O
I/O
P0[5]
Analog column mux input and column output
3
I/O
I/O
P0[3]
Analog column mux input and column output
4
I/O
I
P0[1]
Analog column mux input
5
I/O
6
I/O
7
I/O
8
I/O
9
P2[7]
P2[5]
I
P2[3]
Direct switched capacitor block input
I
P2[1]
Direct switched capacitor block input
SMP
Switch mode pump (SMP) connection to
external components required
Power
10
I/O
P1[7]
I2C serial clock (SCL)
11
I/O
P1[5]
I2C serial data (SDA)
12
I/O
P1[3]
13
I/O
P1[1]
14
Power
VSS
Ground connection
I/O
P1[0]
Crystal (XTALout), I2C Serial Data (SDA),
ISSP-SDATA[3]
16
I/O
P1[2]
17
I/O
P1[4]
18
I/O
P1[6]
Input
XRES
Active high external reset with internal
pull-down
Direct switched capacitor block input
I/O
I
P2[0]
21
I/O
I
P2[2]
Direct switched capacitor block input
22
I/O
P2[4]
External analog ground (AGND)
23
I/O
P2[6]
External voltage reference (VREF)
24
I/O
I
P0[0]
Analog column mux input
25
I/O
I/O
P0[2]
Analog column mux input and column output
26
I/O
I/O
P0[4]
Analog column mux input and column output
27
I/O
I
P0[6]
Analog column mux input
VDD
Supply voltage
Power
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PDIP
SSOP
SOIC
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VDD
P0[6], A, I
P0[4], A, IO
P0[2], A, IO
P0[0], A, I
P2[6], External VREF
P2[4], External AGND
P2[2], A, I
P2[0], A, I
XRES
P1[6]
P1[4], EXTCLK
P1[2]
P1[0], XTALout, I2CSDA
Optional external clock input (EXTCLK)
20
28
A, I, P0[7]
A, IO, P0[5]
A, IO, P0[3]
A, I, P0[1]
P2[7]
P2[5]
A, I, P2[3]
A, I, P2[1]
SMP
I2C SCL, P1[7]
I2C SDA, P1[5]
P1[3]
I2C SCL, XTALin, P1[1]
VSS
Crystal (XTALin), I2C Serial Clock (SCL),
ISSP-SCLK[3]
15
19
Figure 3. CY8C29466 28-Pin PSoC Device
LEGEND: A = Analog, I = Input, and O = Output.
Note
3. These are the ISSP pins, which are not High Z at Power On Reset (POR). See the PSoC Programmable System-on-Chip Technical Reference Manual for details.
Document Number: 38-12013 Rev. *S
Page 8 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
44-Pin Part Pinout
Table 3. 44-Pin Part Pinout (TQFP)
Analog
Pin
Name
Description
I/O
2
I/O
I
P2[3]
Direct switched capacitor block input
3
I/O
I
P2[1]
Direct switched capacitor block input
4
I/O
P4[7]
5
I/O
P4[5]
6
I/O
P4[3]
7
I/O
SMP
Switch mode pump (SMP) connection to
external components required
9
I/O
P3[7]
10
I/O
P3[5]
11
I/O
P3[3]
12
I/O
P3[1]
13
I/O
P1[7]
I2C SCL
14
I/O
P1[5]
I2C SDA
15
I/O
P1[3]
16
I/O
P1[1]
17
Power
Crystal (XTALin), I2C SCL, ISSP-SCLK[4]
VSS
Ground connection
18
I/O
P1[0]
Crystal (XTALout), I2C SDA, ISSP-SDATA[4]
19
I/O
P1[2]
20
I/O
P1[4]
21
I/O
P1[6]
22
I/O
P3[0]
23
I/O
P3[2]
24
I/O
P3[4]
25
I/O
26
Optional EXTCLK
P3[6]
Input
XRES
P2[5]
A, I, P2[3]
A, I, P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
SMP
P3[7]
P3[5]
P3[3]
1
2
3
4
5
6
7
8
9
10
11
TQFP
33 P2[4], External AGND
32 P2[2], A, I
31 P2[0], A, I
30 P4[6]
29 P4[4]
28 P4[2]
27 P4[0]
26 XRES
25 P3[6]
24 P3[4]
23 P3[2]
Active high external reset with internal
pull-down
27
I/O
P4[0]
28
I/O
P4[2]
29
I/O
P4[4]
30
I/O
31
I/O
I
P2[0]
Direct switched capacitor block input
32
I/O
I
P2[2]
Direct switched capacitor block input
33
I/O
P2[4]
External analog ground (AGND)
34
I/O
P2[6]
External voltage reference (VREF)
35
I/O
I
P0[0]
Analog column mux input
36
I/O
I/O
P0[2]
Analog column mux input and column output
37
I/O
I/O
P0[4]
Analog column mux input and column output
38
I/O
I
P0[6]
Analog column mux input
39
44
43
42
41
40
39
38
37
36
35
34
P4[1]
Power
12
13
14
15
16
17
18
19
20
21
22
8
P2[5]
P2[7]
P0[1], A, I
P0[3], A, IO
P0[5], A, IO
P0[7], A, I
VDD
1
Figure 4. CY8C29566 44-Pin PSoC Device
P0[6], A, I
P0[4], A, IO
P0[2], A, IO
P0[0], A, I
P2[6], External VREF
Type
Digital
P3[1]
I2C SCL, P1[7]
I2C SDA, P1[5]
P1[3]
I2C SCL, XTALin, P1[1]
VSS
I2CSDA, XTALout, P1[0]
P1[2]
EXTCLK, P1[4]
P1[6]
P3[0]
Pin
No.
P4[6]
Power
VDD
Supply voltage
40
I/O
I
P0[7]
Analog column mux input
41
I/O
I/O
P0[5]
Analog column mux input and column output
42
I/O
I/O
P0[3]
Analog column mux input and column output
43
I/O
I
P0[1]
Analog column mux input
44
I/O
P2[7]
LEGEND: A = Analog, I = Input, and O = Output.
Note
4. These are the ISSP pins, which are not High Z at POR. See the PSoC Programmable System-on-Chip Technical Reference Manual for details.
Document Number: 38-12013 Rev. *S
Page 9 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
48-Pin Part Pinout
Table 4. 48-Pin Part Pinout (SSOP)
Pin
No.
Type
Digital
Analog
Pin
Name
Description
1
I/O
I
P0[7]
Analog column mux input
2
I/O
I/O
P0[5]
Analog column mux input and column output
3
I/O
I/O
P0[3]
Analog column mux input and column output
4
I/O
I
P0[1]
Analog column mux input
5
I/O
6
I/O
7
I/O
I
P2[3]
Direct switched capacitor block input
8
I/O
I
P2[1]
Direct switched capacitor block input
9
I/O
P4[7]
10
I/O
P4[5]
11
I/O
P4[3]
12
I/O
13
P2[7]
P2[5]
P4[1]
Power
SMP
Switch mode pump (SMP) connection to
external components required
14
I/O
P3[7]
15
I/O
P3[5]
16
I/O
P3[3]
17
I/O
P3[1]
18
I/O
P5[3]
19
I/O
P5[1]
20
I/O
P1[7]
I2C SCL
21
I/O
P1[5]
I2C SDA
22
I/O
P1[3]
23
I/O
24
P1[1]
Power
Ground connection
Crystal (XTALout), I2C SDA, ISSP-SDATA[5]
25
I/O
P1[0]
26
I/O
P1[2]
27
I/O
P1[4]
28
I/O
P1[6]
29
I/O
P5[0]
30
I/O
P5[2]
31
I/O
P3[0]
32
I/O
P3[2]
33
I/O
P3[4]
34
I/O
35
Crystal (XTALin), I2C SCL, ISSP-SCLK[5]
VSS
A, I, P0[7]
A, IO, P0[5]
A, IO, P0[3]
A, I, P0[1]
P2[7]
P2[5]
A, I, P2[3]
A, I, P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
SMP
P3[7]
P3[5]
P3[3]
P3[1]
P5[3]
P5[1]
I2C SCL, P1[7]
I2C SDA, P1[5]
P1[3]
I2C SCL, XTALin, P1[1]
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SSOP
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
VDD
P0[6], A, I
P0[4], A, IO
P0[2], A, IO
P0[0], A, I
P2[6], External VREF
P2[4], External AGND
P2[2], A, I
P2[0], A, I
P4[6]
P4[4]
P4[2]
P4[0]
XRES
P3[6]
P3[4]
P3[2]
P3[0]
P5[2]
P5[0]
P1[6]
P1[4], EXTCLK
P1[2]
P1[0], XTALout, I2C SDA
Optional EXTCLK
P3[6]
Input
XRES
Active high external reset with internal
pull-down
36
I/O
P4[0]
37
I/O
P4[2]
38
I/O
P4[4]
39
I/O
40
I/O
I
P2[0]
41
I/O
I
P2[2]
Direct switched capacitor block input
42
I/O
P2[4]
External Analog Ground (AGND)
43
I/O
P2[6]
External Voltage Reference (VREF)
44
I/O
I
P0[0]
Analog column mux input
45
I/O
I/O
P0[2]
Analog column mux input and column output
46
I/O
I/O
P0[4]
Analog column mux input and column output
47
I/O
I
P0[6]
Analog column mux input
VDD
Supply voltage
48
Figure 5. CY8C29666 48-Pin PSoC Device
P4[6]
Power
Direct switched capacitor block input
LEGEND: A = Analog, I = Input, and O = Output.
Note
5. These are the ISSP pins, which are not High Z at POR. See the PSoC Programmable System-on-Chip Technical Reference Manual for details.
Document Number: 38-12013 Rev. *S
Page 10 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 5. 48-Pin Part Pinout (QFN)[7]
I
P2[3]
Direct switched capacitor block input
I/O
I
P2[1]
Direct switched capacitor block input
3
I/O
P4[7]
4
I/O
P4[5]
5
I/O
P4[3]
6
I/O
7
P4[1]
Power
SMP
Switch mode pump (SMP) connection to
external components required
8
I/O
P3[7]
9
I/O
P3[5]
10
I/O
P3[3]
11
I/O
P3[1]
12
I/O
P5[3]
13
I/O
P5[1]
14
I/O
P1[7]
I2C SCL
15
I/O
P1[5]
I2C SDA
16
I/O
P1[3]
17
I/O
P1[1]
18
Power
Crystal (XTALin), I2C SCL, ISSP-SCLK[6]
VSS
Ground connection
19
I/O
P1[0]
Crystal (XTALout), I2C SDA, ISSP-SDATA[6]
20
I/O
P1[2]
21
I/O
P1[4]
22
I/O
P1[6]
23
I/O
P5[0]
24
I/O
P5[2]
25
I/O
P3[0]
26
I/O
P3[2]
27
I/O
P3[4]
28
I/O
29
Optional EXTCLK
1
2
3
4
5
6
7
8
9
10
11
12
QFN
(Top View)
36
35
34
33
32
31
30
29
28
27
26
25
P2[4], External AGND
P2[2], A, I
P2[0], A, I
P4[6]
P4[4]
P4[2]
P4[0]
XRES
P3[6]
P3[4]
P3[2]
P3[0]
P3[6]
Input
XRES
Active high external reset with internal
pull-down
30
I/O
P4[0]
31
I/O
P4[2]
32
I/O
P4[4]
33
I/O
34
I/O
I
P2[0]
Direct switched capacitor block input
35
I/O
I
P2[2]
Direct switched capacitor block input
36
I/O
P2[4]
External analog ground (AGND)
37
I/O
P2[6]
External voltage reference (VREF)
38
I/O
I
P0[0]
Analog column mux input
39
I/O
I/O
P0[2]
Analog column mux input and column output
40
I/O
I/O
P0[4]
Analog column mux input and column output
41
I/O
I
P0[6]
Analog column mux input
42
A, I, P2[3]
A, I, P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
SMP
P3[7]
P3[5]
P3[3]
P3[1]
P5[3]
38
37
I/O
2
42
41
40
39
1
Figure 6. CY8C29666 48-Pin PSoC Device
P2[5]
P2[7]
P0[1], A, I
P0[3], A, IO
P0[5], A, IO
P0[7], A, I
VDD
P0[6], A, I
P0[4], A, IO
P0[2], A, IO
P0[0], A, I
P2[6], External VREF
Description
48
47
46
45
44
43
Pin
Name
Analog
13
14
I2C SDA, P1[5] 15
P1[3] 16
I2C SCL, XTALin, P1[1] 17
VSS
18
I2C SDA, XTALout, P1[0] 19
P1[2] 20
EXTCLK, P1[4] 21
P1[6] 22
P5[0] 23
P5[2] 24
Type
Digital
P5[1]
I2C SCL, P1[7]
Pin
No.
P4[6]
Power
VDD
Supply voltage
43
I/O
I
P0[7]
Analog column mux input
44
I/O
I/O
P0[5]
Analog column mux input and column output
45
I/O
I/O
P0[3]
Analog column mux input and column output
46
I/O
I
P0[1]
Analog column mux input
47
I/O
P2[7]
48
I/O
P2[5]
LEGEND: A = Analog, I = Input, and O = Output.
Notes
6. These are the ISSP pins, which are not High Z at POR. See the PSoC Programmable System-on-Chip Technical Reference Manual for details.
7. The QFN package has a center pad that must be connected to ground (VSS).
Document Number: 38-12013 Rev. *S
Page 11 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
100-Pin Part Pinout
Table 6. 100-Pin Part Pinout (TQFP)
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
Type
Digital Analog
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
I
I
I
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Name
Description
NC
NC
P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
NC
No connection
No connection
Analog column mux input
NC
SMP
No connection
Switch mode pump (SMP) connection to
external components required
Ground connection
VSS
P3[7]
P3[5]
P3[3]
P3[1]
P5[7]
P5[5]
P5[3]
P5[1]
P1[7]
NC
NC
NC
P1[5]
P1[3]
P1[1]
NC
VDD
NC
VSS
NC
P7[7]
P7[6]
P7[5]
P7[4]
P7[3]
P7[2]
P7[1]
P7[0]
P1[0]
P1[2]
P1[4]
P1[6]
NC
NC
NC
Direct switched capacitor block input
Direct switched capacitor block input
No connection
I2C SCL
No connection
No connection
No connection
I2C SDA
Crystal (XTALin), I2C Serial Clock (SCL),
ISSP-SCLK[8]
No connection
Supply voltage
No connection
Ground connection
No connection
Crystal (XTALout), I2C Serial Data (SDA),
ISSP-SDATA[8]
Optional EXTCLK
No connection
No connection
No connection
Pin
No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Type
Digital Analog
Name
NC
P5[0]
P5[2]
P5[4]
P5[6]
P3[0]
P3[2]
P3[4]
P3[6]
NC
NC
XRES
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Input
I/O
I/O
Description
No connection
No connection
No connection
Active high external reset with internal
pull-down
P4[0]
P4[2]
Power
I/O
I/O
I/O
I/O
I/O
I
I
I/O
I/O
I
I/O
I/O
I/O
I/O
I/O
I
Power
Power
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
I/O
I/O
VSS
P4[4]
P4[6]
P2[0]
P2[2]
P2[4]
NC
P2[6]
NC
P0[0]
NC
NC
P0[2]
NC
P0[4]
NC
Ground connection
Direct switched capacitor block input
Direct switched capacitor block input
External Analog Ground (AGND)
No connection
External Voltage Reference (VREF)
No connection
Analog column mux input
No connection
No connection
Analog column mux input and column output
No connection
Analog column mux input and column output
No connection
P0[6]
VDD
VDD
VSS
VSS
P6[0]
P6[1]
P6[2]
P6[3]
P6[4]
P6[5]
P6[6]
P6[7]
NC
Analog column mux input
Supply voltage
Supply voltage
Ground connection
Ground connection
P0[7]
NC
P0[5]
NC
P0[3]
NC
Analog column mux input
No connection
Analog column mux input and column output
No connection
Analog column mux input and column output
No connection
No connection
LEGEND: A = Analog, I = Input, and O = Output.
Note
8. These are the ISSP pins, which are not High Z at POR. See the PSoC Programmable System-on-Chip Technical Reference Manual for details.
Document Number: 38-12013 Rev. *S
Page 12 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
VDD
VDD
P0[6], A, I
NC
P0[4], A, IO
NC
P0[2], A, IO
NC
87
86
85
84
83
82
81
80
79
78
77
76
P6[7]
P6[6]
P6[5]
P6[4]
P6[3]
P6[2]
P6[1]
P6[0]
VSS
VSS
TQFP
Document Number: 38-12013 Rev. *S
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
P0[0], A, I
NC
P2[6], External VREF
NC
P2[4], External AGND
P2[2], A, I
P2[0], A, I
P4[6]
P4[4]
VSS
P4[2]
P4[0]
XRES
NC
NC
P3[6]
P3[4]
P3[2]
P3[0]
P5[6]
P5[4]
P5[2]
P5[0]
NC
NC
NC
P7[7]
P7[6]
P7[5]
P7[4]
P7[3]
P7[2]
P7[1]
P7[0]
XTALout, I2C SDA, P1[0]
P1[2]
EXTCLK, P1[4]
P1[6]
NC
NC
NC
I2C SDA, P1[5]
P1[3]
XTALin, I2C SCL, P1[1]
NC
VDD
NC
VSS
NC
A, I, P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
NC
NC
SMP
VSS
P3[7]
P3[5]
P3[3]
P3[1]
P5[7]
P5[5]
P5[3]
P5[1]
I2C SCL, P1[7]
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
NC
A, I, P0[1]
P2[7]
P2[5]
A, I, P2[3]
100
99
98
97
96
95
94
93
92
91
90
89
88
NC
P0[3], A, IO
NC
P0[5], A, IO
NC
P0[7], A, I
NC
Figure 7. CY8C29866 100-Pin PSoC Device
Page 13 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
100-Pin Part Pinout (On-Chip Debug)
The 100-pin TQFP part is for the CY8C29000 On-Chip Debug (OCD) PSoC device.
Note OCD parts are only used for in-circuit debugging. OCD parts are NOT available for production
1
2
3
4
5
6
7
8
9
10
11
12
13
14
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
I
Power
NC
NC
P0[1]
P2[7]
P2[5]
P2[3]
P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
OCDE
OCDO
SMP
Description
No internal connection
No internal connection
Analog column mux input
Direct switched capacitor block input
Direct switched capacitor block input
OCD even data I/O
OCD odd data output
Switch Mode Pump (SMP) connection to required
external components
Ground connection
15
Power
VSS
16
I/O
P3[7]
17
I/O
P3[5]
18
I/O
P3[3]
19
I/O
P3[1]
20
I/O
P5[7]
21
I/O
P5[5]
22
I/O
P5[3]
23
I/O
P5[1]
24
I/O
P1[7]
I2C SCL
25
NC
No internal connection
26
NC
No internal connection
27
NC
No internal connection
28
I/O
P1[5]
I2C SDA
29
I/O
P1[3]
IFMTEST
30
I/O
P1[1][9] Crystal (XTALin), I2C SCL, TC SCLK.
31
NC
No internal connection
32
Power
VDD
Supply voltage
33
NC
No internal connection
34
Power
VSS
Ground connection
35
NC
No internal connection
36
I/O
P7[7]
37
I/O
P7[6]
38
I/O
P7[5]
39
I/O
P7[4]
40
I/O
P7[3]
41
I/O
P7[2]
42
I/O
P7[1]
43
I/O
P7[0]
44
I/O
P1[0]*
Crystal (XTALout), I2C SDA, TC SDATA
45
I/O
P1[2]
VFMTEST
46
I/O
P1[4]
Optional External Clock Input (EXTCLK)
47
I/O
P1[6]
48
NC
No internal connection
49
NC
No internal connection
50
NC
No internal connection
LEGEND A = Analog, I = Input, O = Output, NC = No Connection, TC/TM: Test.
Pin
No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Analog
Name
Digital
Analog
Pin
No.
Digital
Table 7. 100-Pin OCD Part Pinout (TQFP)
Name
NC
P5[0]
P5[2]
P5[4]
P5[6]
P3[0]
P3[2]
P3[4]
P3[6]
HCLK
CCLK
XRES
P4[0]
P4[2]
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Input
I/O
I/O
Power
I/O
I/O
I/O I
I/O I
I/O
I/O
I/O
I
I/O
I/O
I/O
I/O
I/O
I
Power
Power
Power
Power
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
I/O
I/O
VSS
P4[4]
P4[6]
P2[0]
P2[2]
P2[4]
NC
P2[6]
NC
P0[0]
NC
NC
P0[2]
NC
P0[4]
NC
P0[6]
VDD
VDD
VSS
VSS
P6[0]
P6[1]
P6[2]
P6[3]
P6[4]
P6[5]
P6[6]
P6[7]
NC
P0[7]
NC
P0[5]
NC
P0[3]
NC
Description
No internal connection
OCD high speed clock output
OCD CPU clock output
Active high pin reset with internal pull-down
Ground connection
Direct switched capacitor block input
Direct switched capacitor block input
External Analog Ground (AGND) input
No internal connection
External Voltage Reference (VREF) input
No internal connection
Analog column mux input
No internal connection
No internal connection
Analog column mux input and column output
No internal connection
Analog column mux input and column output, VREF
No internal connection
Analog column mux input
Supply voltage
Supply voltage
Ground connection
Ground connection
No internal connection
Analog column mux input
No internal connection
Analog column mux input and column output
No internal connection
Analog column mux input and column output
No internal connection
Note
9. ISSP pin which is not High-Z at POR.
Document Number: 38-12013 Rev. *S
Page 14 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
77
76
P6[0]
VSS
VSS
VDD
VDD
P0[6], AI
NC
P0[4], AIO
NC
P0[2], AIO
NC
87
86
85
84
83
82
81
80
79
78
90
89
88
P6[7]
P6[6]
P6[5]
P6[4]
P6[3]
P6[2]
P6[1]
98
97
96
95
94
93
92
91
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
OCD TQFP
NC
P0[0] , AI
NC
P2[6] , External VREF
NC
P2[4] , External AGND
P2[2] , AI
P2[0] , AI
P4[6]
P4[4]
VSS
P4[2]
P4[0]
XRES
CCLK
HCLK
P3[6]
P3[4]
P3[2]
P3[0]
P5[6]
P5[4]
P5[2]
P5[0]
NC
NC
NC
XTALout, I2C SDA, P1[0]
P1[2]
EXTCLK, P1[4]
P1[6]
NC
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Document Number: 38-12013 Rev. *S
NC
VSS
NC
P7[7]
P7[6]
P7[5]
P7[4]
P7[3]
P7[2]
P7[1]
P7[0]
54
53
52
51
26
27
28
29
30
31
32
33
34
35
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
NC
NC
I2C SDA, P1[5]
P1[3]
XTALin, I2C SCL, P1[1]
NC
VDD
NC
NC
AI , P0[1]
P2[7]
P2[5]
AI , P2[3]
AI , P2[1]
P4[7]
P4[5]
P4[3]
P4[1]
OCDE
OCDO
SMP
Vss
P3[7]
P3[5]
P3[3]
P3[1]
P5[7]
P5[5]
P5[3]
P5[1]
I2 C SCL, P1[7]
NC
100
99
NC
P0[3], AIO
NC
P0[5], AIO
NC
P0[7], AI
NC
Figure 8. CY8C29000 OCD (Not for Production)
Page 15 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Register Reference
This section lists the registers of the CY8C29x66 PSoC device. For detailed register information, refer to the
PSoC Programmable System-on-Chip Technical Reference Manual.
Register Conventions
The register conventions specific to this section are listed in Table 8.
Table 8. Register Conventions
Convention
R
W
L
C
#
Description
Read register or bit(s)
Write register or bit(s)
Logical register or bit(s)
Clearable register or bit(s)
Access is bit specific
Register Mapping Tables
The PSoC device has a total register address space of 512 bytes. The register space is referred to as I/O space and is divided into
two banks. The XOI bit in the flag register (CPU_F) determines which bank the user is currently in. When the XOI bit is set the user
is in Bank 1.
Note In the register mapping tables, blank fields are reserved and should not be accessed.
Document Number: 38-12013 Rev. *S
Page 16 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 9. Register Map Bank 0 Table: User Space
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
PRT3DR
PRT3IE
PRT3GS
PRT3DM2
PRT4DR
PRT4IE
PRT4GS
PRT4DM2
PRT5DR
PRT5IE
PRT5GS
PRT5DM2
PRT6DR
PRT6IE
PRT6GS
PRT6DM2
PRT7DR
PRT7IE
PRT7GS
PRT7DM2
DBB00DR0
DBB00DR1
DBB00DR2
DBB00CR0
DBB01DR0
DBB01DR1
DBB01DR2
DBB01CR0
DCB02DR0
DCB02DR1
DCB02DR2
DCB02CR0
DCB03DR0
DCB03DR1
DCB03DR2
DCB03CR0
DBB10DR0
DBB10DR1
DBB10DR2
DBB10CR0
DBB11DR0
DBB11DR1
DBB11DR2
DBB11CR0
DCB12DR0
DCB12DR1
DCB12DR2
DCB12CR0
DCB13DR0
DCB13DR1
DCB13DR2
DCB13CR0
Addr (0,Hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
Name
DBB20DR0
DBB20DR1
DBB20DR2
DBB20CR0
DBB21DR0
DBB21DR1
DBB21DR2
DBB21CR0
DCB22DR0
DCB22DR1
DCB22DR2
DCB22CR0
DCB23DR0
DCB23DR1
DCB23DR2
DCB23CR0
DBB30DR0
DBB30DR1
DBB30DR2
DBB30CR0
DBB31DR0
DBB31DR1
DBB31DR2
DBB31CR0
DCB32DR0
DCB32DR1
DCB32DR2
DCB32CR0
DCB33DR0
DCB33DR1
DCB33DR2
DCB33CR0
AMX_IN
ARF_CR
CMP_CR0
ASY_CR
CMP_CR1
TMP_DR0
TMP_DR1
TMP_DR2
TMP_DR3
ACB00CR3
ACB00CR0
ACB00CR1
ACB00CR2
ACB01CR3
ACB01CR0
ACB01CR1
ACB01CR2
ACB02CR3
ACB02CR0
ACB02CR1
ACB02CR2
ACB03CR3
ACB03CR0
ACB03CR1
ACB03CR2
Blank fields are Reserved and should not be accessed.
Document Number: 38-12013 Rev. *S
Addr (0,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Access
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
#
W
RW
#
RW
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
ASC12CR0
ASC12CR1
ASC12CR2
ASC12CR3
ASD13CR0
ASD13CR1
ASD13CR2
ASD13CR3
ASD20CR0
ASD20CR1
ASD20CR2
ASD20CR3
ASC21CR0
ASC21CR1
ASC21CR2
ASC21CR3
ASD22CR0
ASD22CR1
ASD22CR2
ASD22CR3
ASC23CR0
ASC23CR1
ASC23CR2
ASC23CR3
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
MUL1_X
MUL1_Y
MUL1_DH
MUL1_DL
ACC1_DR1
ACC1_DR0
ACC1_DR3
ACC1_DR2
RDI0RI
RDI0SYN
RDI0IS
RDI0LT0
RDI0LT1
RDI0RO0
RDI0RO1
RDI1RI
RDI1SYN
RDI1IS
RDI1LT0
RDI1LT1
RDI1RO0
RDI1RO1
Addr (0,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
W
W
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
RDI2RI
RDI2SYN
RDI2IS
RDI2LT0
RDI2LT1
RDI2RO0
RDI2RO1
RDI3RI
RDI3SYN
RDI3IS
RDI3LT0
RDI3LT1
RDI3RO0
RDI3RO1
CUR_PP
STK_PP
IDX_PP
MVR_PP
MVW_PP
I2C_CFG
I2C_SCR
I2C_DR
I2C_MSCR
INT_CLR0
INT_CLR1
INT_CLR2
INT_CLR3
INT_MSK3
INT_MSK2
INT_MSK0
INT_MSK1
INT_VC
RES_WDT
DEC_DH
DEC_DL
DEC_CR0
DEC_CR1
MUL0_X
MUL0_Y
MUL0_DH
MUL0_DL
ACC0_DR1
ACC0_DR0
ACC0_DR3
ACC0_DR2
CPU_F
RW
RW
RW
RW
RW
RW
RW
CPU_SCR1
CPU_SCR0
Addr (0,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RC
W
RC
RC
RW
RW
W
W
R
R
RW
RW
RW
RW
RL
#
#
# Access is bit specific.
Page 17 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 10. Register Map Bank 1 Table: Configuration Space
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
PRT3DM0
PRT3DM1
PRT3IC0
PRT3IC1
PRT4DM0
PRT4DM1
PRT4IC0
PRT4IC1
PRT5DM0
PRT5DM1
PRT5IC0
PRT5IC1
PRT6DM0
PRT6DM1
PRT6IC0
PRT6IC1
PRT7DM0
PRT7DM1
PRT7IC0
PRT7IC1
DBB00FN
DBB00IN
DBB00OU
Addr (1,Hex) Access
Name
00
RW
DBB20FN
01
RW
DBB20IN
02
RW
DBB20OU
03
RW
04
RW
DBB21FN
05
RW
DBB21IN
06
RW
DBB21OU
07
RW
08
RW
DCB22FN
09
RW
DCB22IN
0A
RW
DCB22OU
0B
RW
0C
RW
DCB23FN
0D
RW
DCB23IN
0E
RW
DCB23OU
0F
RW
10
RW
DBB30FN
11
RW
DBB30IN
12
RW
DBB30OU
13
RW
14
RW
DBB31FN
15
RW
DBB31IN
16
RW
DBB31OU
17
RW
18
RW
DCB32FN
19
RW
DCB32IN
1A
RW
DCB32OU
1B
RW
1C
RW
DCB33FN
1D
RW
DCB33IN
1E
RW
DCB33OU
1F
RW
20
RW
CLK_CR0
21
RW
CLK_CR1
22
RW
ABF_CR0
23
AMD_CR0
DBB01FN
24
RW
DBB01IN
25
RW
DBB01OU
26
RW
AMD_CR1
27
ALT_CR0
DCB02FN
28
RW
ALT_CR1
DCB02IN
29
RW
CLK_CR2
DCB02OU
2A
RW
2B
DCB03FN
2C
RW
TMP_DR0
DCB03IN
2D
RW
TMP_DR1
DCB03OU
2E
RW
TMP_DR2
2F
TMP_DR3
DBB10FN
30
RW
ACB00CR3
DBB10IN
31
RW
ACB00CR0
DBB10OU
32
RW
ACB00CR1
33
ACB00CR2
DBB11FN
34
RW
ACB01CR3
DBB11IN
35
RW
ACB01CR0
DBB11OU
36
RW
ACB01CR1
37
ACB01CR2
DCB12FN
38
RW
ACB02CR3
DCB12IN
39
RW
ACB02CR0
DCB12OU
3A
RW
ACB02CR1
3B
ACB02CR2
DCB13FN
3C
RW
ACB03CR3
DCB13IN
3D
RW
ACB03CR0
DCB13OU
3E
RW
ACB03CR1
3F
ACB03CR2
Blank fields are Reserved and should not be accessed.
Document Number: 38-12013 Rev. *S
Addr (1,Hex)
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
ASC12CR0
ASC12CR1
ASC12CR2
ASC12CR3
ASD13CR0
ASD13CR1
ASD13CR2
ASD13CR3
ASD20CR0
ASD20CR1
ASD20CR2
ASD20CR3
ASC21CR0
ASC21CR1
ASC21CR2
ASC21CR3
ASD22CR0
ASD22CR1
ASD22CR2
ASD22CR3
ASC23CR0
ASC23CR1
ASC23CR2
ASC23CR3
Addr (1,Hex)
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
RDI0RI
B0
RDI0SYN
B1
RDI0IS
B2
RDI0LT0
B3
RDI0LT1
B4
RDI0RO0
B5
RDI0RO1
B6
B7
RDI1RI
B8
RDI1SYN
B9
RDI1IS
BA
RDI1LT0
BB
RDI1LT1
BC
RDI1RO0
BD
RDI1RO1
BE
BF
# Access is bit specific.
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Name
RDI2RI
RDI2SYN
RDI2IS
RDI2LT0
RDI2LT1
RDI2RO0
RDI2RO1
RDI3RI
RDI3SYN
RDI3IS
RDI3LT0
RDI3LT1
RDI3RO0
RDI3RO1
GDI_O_IN
GDI_E_IN
GDI_O_OU
GDI_E_OU
OSC_GO_EN
OSC_CR4
OSC_CR3
OSC_CR0
OSC_CR1
OSC_CR2
VLT_CR
VLT_CMP
DEC_CR2
IMO_TR
ILO_TR
BDG_TR
ECO_TR
RW
RW
RW
RW
RW
RW
RW
CPU_F
RW
RW
RW
RW
RW
RW
RW
FLS_PR1
CPU_SCR1
CPU_SCR0
Addr (1,Hex)
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
Access
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
RW
W
W
RW
W
RL
RW
#
#
Page 18 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Electrical Specifications
This section presents the DC and AC electrical specifications of the CY8C29x66 PSoC device. For the most up-to-date electrical
specifications, confirm that you have the most recent datasheet by going to the web at http://www.cypress.com.
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted. Refer to Table 27 for the electrical specifications
on the internal main oscillator (IMO) using SLIMO mode.
Figure 9. Voltage versus CPU Frequency
Figure 10. IMO Frequency Options
5.25
4.75
Vdd Voltage
Vdd Voltage
l id g
V a a tin
n
r
pe g io
Re
O
4.75
SLIMO Mode = 0
5.25
3.60
S L IM O
M o d e =1
S L IM O
M o d e =0
S L IM O
M o d e =1
S L IM O
M o d e =0
3.00
3.00
9 3 kHz
12 MHz
2 4 MHz
9 3 kHz
1 2 MHz
6 MHz
2 4 MHz
IM O F r e q u e n cy
C PU F r e q u e n c y
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 11. Absolute Maximum Ratings
Symbol
Description
Min
Typ
Max
Unit
Notes
–55
25
+100
°C
Higher storage temperatures
reduce data retention time.
Recommended storage temperature is +25 °C ± 25 °C. Extended
duration storage temperatures
higher than 65 °C degrade
reliability.
–
125
See
package
label
°C
See
package
label
–
72
Hours
TSTG
Storage temperature
TBAKETEMP
Bake temperature
TBAKETIME
Bake time
TA
Ambient temperature with power applied
–40
–
+85
°C
VDD
Supply voltage on VDD relative to VSS
–0.5
–
+6.0
V
VIO
DC input voltage
VSS – 0.5
–
VDD + 0.5
V
VIOZ
DC voltage applied to tristate
VSS – 0.5
–
VDD + 0.5
V
IMIO
Maximum current into any port pin
–25
–
+50
mA
IMAIO
Maximum current into any port pin configured as
analog driver
–50
–
+50
mA
ESD
Electrostatic discharge voltage
2000
–
–
V
LU
Latch-up current
–
–
200
mA
Document Number: 38-12013 Rev. *S
Human body model ESD.
Page 19 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Operating Temperature
Table 12. Operating Temperature
Symbol
TA
TJ
Description
Ambient temperature
Junction temperature
Min
–40
–40
Typ
–
–
Max
+85
+100
Unit
°C
°C
Notes
The temperature rise from
ambient to junction is package
specific. See “Thermal
Impedances” on page 49. You
must limit the power
consumption to comply with this
requirement.
DC Electrical Characteristics
DC Chip-Level Specifications
Table 13 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are for
design guidance only.
Table 13. DC Chip-Level Specifications
Symbol
Description
Min
Typ
Max
Unit
Notes
s
V
See DC POR, SMP, and LVD Specifications on page
33.
mA Conditions are 5.0 V, TA = 25 °C, CPU = 3 MHz,
SYSCLK doubler disabled, VC1 = 1.5 MHz,
VC2 = 93.75 kHz, VC3 = 0.366 kHz.
mA Conditions are VDD = 3.3 V, TA = 25 °C, CPU = 3 MHz,
SYSCLK doubler disabled, VC1 = 1.5 MHz,
VC2 = 93.75 kHz, VC3 = 0.366 kHz.
mA Conditions are VDD = 3.3 V, TA = 25 °C, CPU = 0.75
MHz, SYSCLK doubler disabled,
VC1 = 0.375 MHz, VC2 = 23.44 kHz, VC3 = 0.09 kHz.
µA Conditions are with internal slow speed oscillator,
VDD = 3.3 V, –40 °C ≤ TA ≤ 55 °C.
µA Conditions are with internal slow speed oscillator,
VDD = 3.3 V, 55 °C < TA ≤ 85 °C.
µA Conditions are with properly loaded, 1 µW max,
32.768 kHz crystal. VDD = 3.3 V, –40 °C ≤ TA ≤ 55 °C.
VDD
Supply voltage
3.00
–
5.25
IDD
Supply current
–
8
14
IDD3
Supply current
–
5
9
IDDP
Supply current when IMO = 6 MHz using SLIMO
mode.
–
2
3
ISB
Sleep (Mode) current with POR, LVD, sleep
–
timer, WDT, and internal slow oscillator active.
Sleep (Mode) current with POR, LVD, sleep
–
timer, WDT, and internal slow oscillator active.
Sleep (Mode) current with POR, LVD, sleep
–
timer, WDT, internal slow oscillator, and 32 kHz
crystal oscillator active.
Sleep (Mode) current with POR, LVD, sleep
–
timer, WDT, and 32 kHz crystal oscillator active.
Reference voltage (Bandgap)
1.28
3
10
4
25
4
12
5
27
µA
1.3
1.32
V
ISBH
ISBXTL
ISBXTLH
VREF
Document Number: 38-12013 Rev. *S
Conditions are with properly loaded, 1 µW max,
32.768 kHz crystal. VDD = 3.3 V, 55 °C < TA ≤ 85 °C.
Trimmed for appropriate VDD.
Page 20 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
DC GPIO Specifications
Table 14 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are for
design guidance only.
Table 14. DC GPIO Specifications
Symbol
Description
Min
Typ
Max
Unit
4
5.6
8
kΩ
Pull-down resistor
4
5.6
8
kΩ
High output level
VDD – 1.0
–
–
V
IOH = 10 mA, VDD = 4.75 to 5.25 V (8 total loads,
4 on even port pins (for example, P0[2], P1[4]),
4 on odd port pins (for example, P0[3], P1[5])).
80 mA maximum combined IOH budget.
VOL
Low output level
–
–
0.75
V
IOL = 25 mA, VDD = 4.75 to 5.25 V (8 total loads,
4 on even port pins (for example, P0[2], P1[4]),
4 on odd port pins (for example, P0[3], P1[5])).
150 mA maximum combined IOL budget.
IOH
High level source current
10
–
–
mA
VOH = VDD – 1.0 V, see the limitations of the total
current in the note for VOH
IOL
Low level sink current
25
–
–
mA
VOL = 0.75 V, see the limitations of the total
current in the note for VOL
VIL
Input low level
–
–
0.8
V
VDD = 3.0 to 5.25
VIH
Input high level
2.1
–
–
V
VDD = 3.0 to 5.25
VH
Input hysteresis
–
60
–
mV
IIL
Input leakage (absolute value)
–
1
–
nA
Gross tested to 1 µA.
CIN
Capacitive load on pins as input
–
3.5
10
pF
Package and pin dependent. Temp = 25 °C.
COUT
Capacitive load on pins as output
–
3.5
10
pF
Package and pin dependent. Temp = 25 °C.
RPU
Pull-up resistor
RPD
VOH
Notes
DC Operational Amplifier Specifications
Table 15 and Table 16 list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at
25 °C and are for design guidance only.
The Operational Amplifier is a component of both the Analog Continuous Time PSoC blocks and the Analog Switched Cap PSoC
blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block. Typical parameters apply to 5 V at
25 °C and are for design guidance only.
Table 15. 5-V DC Operational Amplifier Specifications
Symbol
Min
Typ
Max
Unit
Input offset voltage (absolute value)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = Medium, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
–
–
1.6
1.6
1.6
1.6
1.6
1.6
10
10
10
10
10
10
mV
mV
mV
mV
mV
mV
TCVOSOA
Average input offset voltage drift
–
4
23
µV/°C
I
EBOA
Input leakage current (port 0 analog pins)
–
200
–
pA
Gross tested to 1 µA
CINOA
Input capacitance (port 0 analog pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
VOSOA
Description
Document Number: 38-12013 Rev. *S
Notes
Page 21 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 15. 5-V DC Operational Amplifier Specifications (continued)
Symbol
V
CMOA
Description
Min
Typ
Max
Unit
Notes
0
–
VDD
V
0.5
–
VDD – 0.5
V
The common-mode input voltage range
is measured through an analog output
buffer.
The specification includes the
limitations imposed by the
characteristics of the analog output
buffer.
Common mode voltage range (All cases,
except Power = High, Opamp bias = High)
Common mode voltage range (Power = High,
Opamp bias = High)
CMRROA
Common mode rejection ratio
60
–
–
dB
GOLOA
Open loop gain
80
–
–
dB
VDD – 0.01
–
–
V
VOHIGHOA High output voltage swing (internal signals)
VOLOWOA
Low output voltage swing (internal signals)
–
–
0.1
V
ISOA
Supply current (including associated
AGND buffer)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = Medium, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
–
–
150
300
600
1200
2400
4600
200
400
800
1600
3200
6400
µA
µA
µA
µA
µA
µA
Supply voltage rejection ratio
67
80
–
dB
Min
Typ
Max
Unit
PSRROA
VSS ≤ VIN ≤ (VDD – 2.25) or
(VDD – 1.25 V) ≤ VIN ≤ VDD.
Table 16. 3.3-V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input offset voltage (absolute value)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = Medium, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
–
–
1.4
1.4
1.4
1.4
1.4
–
10
10
10
10
10
–
mV
mV
mV
mV
mV
mV
TCVOSOA
Average input offset voltage drift
–
7
40
µV/°C
I
Notes
Power = High, Opamp bias = High
setting is not allowed for 3.3 V VDD
operation.
EBOA
Input leakage current (port 0 analog pins)
–
200
–
pA
Gross tested to 1 µA.
CINOA
Input capacitance (port 0 analog pins)
–
4.5
9.5
pF
Package and pin dependent.
Temp = 25 °C
V
Common mode voltage range
0
–
VDD
V
The common-mode input voltage range
is measured through an analog output
buffer.
The specification includes the limitations
imposed by the characteristics of the
analog output buffer.
CMOA
CMRROA
Common mode rejection ratio
60
–
–
dB
GOLOA
Open loop gain
80
–
–
dB
VOHIGHOA
High output voltage swing (internal signals)
VDD – 0.01
–
–
V
Document Number: 38-12013 Rev. *S
Page 22 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 16. 3.3-V DC Operational Amplifier Specifications (continued)
Symbol
Description
Min
Typ
Max
Unit
–
–
0.01
V
VOLOWOA
Low output voltage swing (internal signals)
ISOA
Supply current
(including associated AGND buffer)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = Medium, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
–
–
150
300
600
1200
2400
–
200
400
800
1600
3200
–
µA
µA
µA
µA
µA
µA
Supply voltage rejection ratio
54
80
–
dB
PSRROA
Notes
Power = High, Opamp bias = High
setting is not allowed for 3.3 V VDD
operation.
VSS ≤ VIN ≤ (VDD – 2.25) or
(VDD – 1.25 V) ≤ VIN ≤ VDD
DC Low-Power Comparator Specifications
Table 17 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, or 2.4 V to 3.0 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters
apply to 5 V at 25 °C and are for design guidance only.
Table 17. DC Low-Power Comparator Specifications
Symbol
Description
Min
Typ
Max
Unit
VREFLPC
Low-power comparator (LPC) reference voltage range
0.2
–
VDD – 1
V
ISLPC
LPC supply current
–
10
40
µA
VOSLPC
LPC voltage offset
–
2.5
30
mV
DC Analog Output Buffer Specifications
Table 18 and Table 19 list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V
at 25 °C and are for design guidance only.
Table 18. 5-V DC Analog Output Buffer Specifications
Symbol
Description
VOSOB
Input offset voltage (absolute value)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
TCVOSOB
Average input offset voltage drift
VCMOB
Common-mode input voltage range
ROUTOB
Output resistance
Power = Low
Power = High
VOHIGHOB
VOLOWOB
Min
Typ
Max
Unit
–
–
–
–
3.2
3.2
3.2
3.2
18
18
18
18
mV
mV
mV
mV
–
5.5
26
µV/°C
0.5
–
VDD – 1.0
V
–
–
–
–
1
1
Ω
Ω
High output voltage swing
(Load = 32 ohms to VDD/2)
Power = Low
Power = High
0.5 × VDD + 1.3
0.5 × VDD + 1.3
–
–
–
–
V
V
Low output voltage swing
(Load = 32 ohms to VDD/2)
Power = Low
Power = High
–
–
–
–
0.5 × VDD – 1.3
0.5 × VDD – 1.3
V
V
Document Number: 38-12013 Rev. *S
Notes
Page 23 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 18. 5-V DC Analog Output Buffer Specifications (continued)
Min
Typ
Max
Unit
ISOB
Symbol
Supply current including bias cell (no load)
Power = Low
Power = High
Description
–
–
1.1
2.6
2
5
mA
mA
PSRROB
Supply voltage rejection ratio
40
64
CL
Load capacitance
–
–
200
pF
Min
Typ
Max
Unit
Notes
dB
This specification
applies to the
external circuit
driven by the analog
output buffer.
Table 19. 3.3-V DC Analog Output Buffer Specifications
Symbol
Description
VOSOB
Input offset voltage (absolute value)
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
3.2
3.2
6
6
20
20
25
25
mV
mV
mV
mV
TCVOSOB
Average input offset voltage drift
Power = Low, Opamp bias = Low
Power = Low, Opamp bias = High
Power = High, Opamp bias = Low
Power = High, Opamp bias = High
–
–
–
–
8
8
12
12
32
32
41
41
µV/°C
µV/°C
µV/°C
µV/°C
0.5
–
VDD – 1.0
V
–
–
–
–
10
10
W
W
VCMOB
Common-mode input voltage range
ROUTOB
Output resistance
Power = Low
Power = High
VOHIGHOB
High output voltage swing
(Load = 32 ohms to VDD/2)
Power = Low
Power = High
0.5 × VDD + 1.0
0.5 × VDD + 1.0
–
–
–
–
V
V
Low output voltage swing
(Load = 32 ohms to VDD/2)
Power = Low
Power = High
–
–
–
–
0.5 × VDD – 1.0
0.5 × VDD – 1.0
V
V
ISOB
Supply current including bias cell (no load)
Power = Low
Power = High
–
–
0.8
2.0
1
5
mA
mA
PSRROB
Supply voltage rejection ratio
60
64
–
dB
CL
Load capacitance
–
–
200
pF
VOLOWOB
Document Number: 38-12013 Rev. *S
Notes
High power setting
is not
recommended.
High power setting
is not
recommended.
This specification
applies to the
external circuit
driven by the
analog output
buffer.
Page 24 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
DC Switch Mode Pump Specifications
Table 20 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and
–40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and
are for design guidance only.
Table 20. DC Switch Mode Pump (SMP) Specifications
Min
Typ
Max
Unit
Notes
VPUMP 5 V
Symbol
5 V output voltage at VDD from
pump
Description
4.75
5.0
5.25
V
Configured as in Note 10. Average,
neglecting ripple. SMP trip voltage
is set to 5.0 V
VPUMP 3 V
3 V output voltage at VDD from
pump
3.00
3.25
3.60
V
Configured as in Note 10. Average,
neglecting ripple. SMP trip voltage
is set to 3.25 V
IPUMP
Available output current
VBAT = 1.5 V, VPUMP = 3.25 V
VBAT = 1.8 V, VPUMP = 5.0 V
8
5
–
–
–
–
mA
mA
VBAT5 V
Input voltage range from battery
1.8
–
5.0
V
Configured as in Note 10. SMP trip
voltage is set to 5.0 V
VBAT3 V
Input voltage range from battery
1.0
–
3.3
V
Configured as in Note 10. SMP trip
voltage is set to 3.25 V
VBATSTART
Minimum input voltage from battery
to start pump
1.2
–
–
V
Configured as in Note 10.0 °C ≤ TA
≤ 100. 1.25 V at TA = –40 °C
ΔVPUMP_Line
Line regulation (over VBAT range)
–
5
–
%VO
Configured as in Note 10. VO is the
“VDD Value for PUMP Trip” specified
by the VM[2:0] setting in the DC
POR and LVD Specification,
Table 24, “DC POR, SMP, and LVD
Specifications,” on page 33
ΔVPUMP_Load
Load regulation
–
5
–
%VO
Configured as in Note 10. VO is the
“VDD Value for PUMP Trip” specified
by the VM[2:0] setting in Table 24,
“DC POR, SMP, and LVD Specifications,” on page 33
ΔVPUMP_Ripple Output voltage ripple (depends on
capacitor/load)
–
100
–
mVpp
Configured as in Note 10. Load is
5 mA
E3
Efficiency
35
50
–
%
Configured as in Note 10. Load is
5 mA. SMP trip voltage is set to
3.25 V
FPUMP
Switching frequency
–
1.4
–
MHz
DCPUMP
Switching duty cycle
–
50
–
%
Configured as in Note 10
SMP trip voltage is set to 3.25 V
SMP trip voltage is set to 5.0 V
Note
10. L1 = 2 µH inductor, C1 = 10 µF capacitor, D1 = Schottky diode. See Figure 11.
Document Number: 38-12013 Rev. *S
Page 25 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 11. Basic Switch Mode Pump Circuit
D1
Vdd
L1
V BAT
+
V PUMP
C1
SMP
Battery
PSoC
Vss
DC Analog Reference Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
The guaranteed specifications for RefHI and RefLO are measured through the analog continuous time PSoC blocks. The power levels
for RefHI and RefLO refer to the analog reference control register. AGND is measured at P2[4] in AGND bypass mode. Each analog
continuous time PSoC block adds a maximum of 10 mV additional offset error to guaranteed AGND specifications from the local
AGND buffer. Reference control power can be set to medium or high unless otherwise noted.
Note Avoid using P2[4] for digital signaling when using an analog resource that depends on the analog reference. Some coupling of
the digital signal may appear on the AGND.
Table 21. 5-V DC Analog Reference Specifications
Reference
ARF_CR[5:3]
Reference Power
Settings
Symbol
Reference
Description
Min
RefPower = High
Opamp bias = High
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.228
VDD/2 + 1.290 VDD/2 + 1.352
VAGND
AGND
VDD/2
VDD/2 – 0.078
VDD/2 – 0.007
VDD/2 + 0.063
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.336
VDD/2 – 1.295
VDD/2 – 1.250
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.224
VDD/2 + 1.293 VDD/2 + 1.356
V
VAGND
AGND
VDD/2
VDD/2 – 0.056
VDD/2 – 0.005
VDD/2 + 0.043
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.338
VDD/2 – 1.298
VDD/2 – 1.255
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.226
VDD/2 + 1.293 VDD/2 + 1.356
V
VAGND
AGND
VDD/2
VDD/2 – 0.057
VDD/2 – 0.006
VDD/2 + 0.044
V
RefPower = High
Opamp bias = Low
0b000
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Typ
Max
Unit
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.337
VDD/2 – 1.298
VDD/2 – 1.256
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.226
VDD/2 + 1.294 VDD/2 + 1.359
V
VAGND
AGND
VDD/2
VDD/2 – 0.047
VDD/2 – 0.004
VDD/2 + 0.035
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.338
VDD/2 – 1.299
VDD/2 – 1.258
V
Document Number: 38-12013 Rev. *S
Page 26 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 21. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR[5:3]
Reference Power
Settings
Symbol
Reference
RefPower = High
Opamp bias = High
VREFHI
Ref High
RefPower = High
Opamp bias = Low
0b001
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b010
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Description
P2[4] + P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
Min
Typ
Max
Unit
P2[4] + P2[6] –
0.085
P2[4] + P2[6] –
0.016
P2[4] + P2[6]
+ 0.044
V
P2[4]
P2[4]
VAGND
AGND
VREFLO
Ref Low
P2[4] – P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] – P2[6] –
0.022
P2[4] – P2[6] + P2[4] – P2[6] +
0.010
0.055
V
VREFHI
Ref High
P2[4] + P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] + P2[6] –
0.077
P2[4] + P2[6] –
0.010
P2[4] + P2[6]
+ 0.051
V
P2[4]
P2[4]
P2[4]
P2[4]
–
VAGND
AGND
VREFLO
Ref Low
P2[4] – P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] – P2[6] –
0.022
P2[4] – P2[6] + P2[4] – P2[6] +
0.005
0.039
V
VREFHI
Ref High
P2[4] + P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] + P2[6] –
0.070
P2[4] + P2[6] –
0.010
P2[4] + P2[6]
+ 0.050
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] – P2[6] –
0.022
P2[4] – P2[6] + P2[4] – P2[6] +
0.005
0.039
V
VREFHI
Ref High
P2[4] + P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
P2[4] + P2[6] –
0.070
P2[4] + P2[6] –
0.007
P2[4] + P2[6]
+ 0.054
V
P2[4]
P2[4]
P2[4]
P2[4]
VAGND
AGND
VREFLO
Ref Low
P2[4] – P2[6]
(P2[4] = VDD/2,
P2[6] = 1.3 V)
VREFHI
Ref High
VDD
VAGND
AGND
P2[4]
VDD/2
P2[4]
P2[4]
P2[4] – P2[6] –
0.022
P2[4] – P2[6] + P2[4] – P2[6] +
0.002
0.032
–
–
V
VDD – 0.037
VDD – 0.009
VDD
V
VDD/2 – 0.061
VDD/2 – 0.006
VDD/2 + 0.047
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.007
VSS + 0.028
V
VREFHI
Ref High
VDD
VDD – 0.039
VDD – 0.006
VDD
V
VAGND
AGND
VDD/2 – 0.049
VDD/2 – 0.005
VDD/2 + 0.036
V
VDD/2
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.019
V
VREFHI
Ref High
VDD
VDD – 0.037
VDD – 0.007
VDD
V
VAGND
AGND
VDD/2 – 0.054
VDD/2 – 0.005
VDD/2 + 0.041
V
VDD/2
VREFLO
Ref Low
VSS
VSS
VSS + 0.006
VSS + 0.024
V
VREFHI
Ref High
VDD
VDD – 0.042
VDD – 0.005
VDD
V
VDD/2 – 0.046
VDD/2 – 0.004
VDD/2 + 0.034
V
VSS
VSS + 0.004
VSS + 0.017
V
VAGND
AGND
VREFLO
Ref Low
Document Number: 38-12013 Rev. *S
VDD/2
VSS
Page 27 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 21. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR[5:3]
Reference Power
Settings
Symbol
Reference
RefPower = High
Opamp bias = High
VREFHI
Ref High
3 × Bandgap
RefPower = High
Opamp bias = Low
0b011
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b100
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Description
Min
Typ
Max
Unit
3.788
3.891
3.986
V
VAGND
AGND
2 × Bandgap
2.500
2.604
3.699
V
VREFLO
Ref Low
Bandgap
1.257
1.306
1.359
V
VREFHI
Ref High
3 × Bandgap
3.792
3.893
3.982
V
2 × Bandgap
2.518
2.602
2.692
V
Bandgap
1.256
1.302
1.354
V
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
3 × Bandgap
3.795
3.894
3.993
V
VAGND
AGND
2 × Bandgap
2.516
2.603
2.698
V
VREFLO
Ref Low
Bandgap
1.256
1.303
1.353
V
VREFHI
Ref High
3 × Bandgap
3.792
3.895
3.986
V
VAGND
AGND
2 × Bandgap
2.522
2.602
2.685
V
VREFLO
Ref Low
Bandgap
1.255
1.301
1.350
V
VREFHI
Ref High
2 × Bandgap +
P2[6] (P2[6] =
1.3 V)
2.495 – P2[6]
2.586 – P2[6]
2.657 – P2[6]
V
VAGND
AGND
2.502
2.604
2.719
V
VREFLO
Ref Low
2 × Bandgap –
P2[6] (P2[6] =
1.3 V)
2.531 – P2[6]
2.611 – P2[6]
2.681 – P2[6]
V
VREFHI
Ref High
2 × Bandgap +
P2[6] (P2[6] =
1.3 V)
2.500 – P2[6]
2.591 – P2[6]
2.662 – P2[6]
V
2 × Bandgap
VAGND
AGND
2.519
2.602
2.693
V
VREFLO
Ref Low
2 × Bandgap –
P2[6] (P2[6] =
1.3 V)
2.530 – P2[6]
2.605 – P2[6]
2.666 – P2[6]
V
VREFHI
Ref High
2 × Bandgap +
P2[6] (P2[6] =
1.3 V)
2.503 – P2[6]
2.592 – P2[6]
2.662 – P2[6]
V
2 × Bandgap
VAGND
AGND
2.517
2.603
2.698
V
VREFLO
Ref Low
2 × Bandgap –
P2[6] (P2[6] =
1.3 V)
2.529 – P2[6]
2.606 – P2[6]
2.665 – P2[6]
V
VREFHI
Ref High
2 × Bandgap +
P2[6] (P2[6] =
1.3 V)
2.505 – P2[6]
2.594 – P2[6]
2.665 – P2[6]
V
VAGND
AGND
2.525
2.602
2.685
V
VREFLO
Ref Low
2.528 – P2[6]
2.603 – P2[6]
2.661 – P2[6]
V
Document Number: 38-12013 Rev. *S
2 × Bandgap
2 × Bandgap
2 × Bandgap –
P2[6] (P2[6] =
1.3 V)
Page 28 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 21. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR[5:3]
Reference Power
Settings
Symbol
Reference
RefPower = High
Opamp bias = High
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
RefPower = High
Opamp bias = Low
0b101
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b110
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b111
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Description
Min
Typ
Max
Unit
P2[4] + 1.222
P2[4] + 1.290
P2[4] + 1.343
V
P2[4]
P2[4]
P2[4]
–
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.331
P2[4] – 1.295
P2[4] – 1.254
V
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.226
P2[4] + 1.293
P2[4] + 1.347
V
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4]
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4]
P2[4] – 1.331
P2[4] – 1.298
P2[4] – 1.259
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.227
P2[4] + 1.294
P2[4] + 1.347
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4]
P2[4] – 1.331
P2[4] – 1.298
P2[4] – 1.259
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.228
P2[4] + 1.295
P2[4] + 1.349
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – 1.332
P2[4] – 1.299
P2[4] – 1.260
V
VREFHI
Ref High
VAGND
AGND
P2[4]
P2[4] – Bandgap
(P2[4] = VDD/2)
2 × Bandgap
2.535
2.598
2.644
V
Bandgap
1.227
1.305
1.398
V
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.009
VSS + 0.038
VREFHI
Ref High
2 × Bandgap
2.530
2.598
2.643
V
VAGND
AGND
Bandgap
1.244
1.303
1.370
V
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.024
VREFHI
Ref High
2 × Bandgap
2.532
2.598
2.644
V
VAGND
AGND
Bandgap
1.239
1.304
1.380
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.006
VSS + 0.026
V
VREFHI
Ref High
2 × Bandgap
2.528
2.598
2.645
V
Bandgap
1.249
1.302
1.362
V
VSS
VSS + 0.004
VSS + 0.018
V
4.155
4.234
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
3.2 × Bandgap
4.041
1.6 × Bandgap
1.998
2.083
2.183
V
VSS
VSS + 0.010
VSS + 0.038
V
4.153
4.236
V
VAGND
AGND
VREFLO
Ref Low
VSS
VREFHI
Ref High
3.2 × Bandgap
4.047
1.6 × Bandgap
2.012
2.082
2.157
V
VSS
VSS + 0.006
VSS + 0.024
V
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
3.2 × Bandgap
4.049
4.154
4.238
V
VAGND
AGND
1.6 × Bandgap
2.008
2.083
2.165
V
VREFLO
Ref Low
VSS
VSS + 0.006
VSS + 0.026
V
VREFHI
Ref High
3.2 × Bandgap
4.047
4.154
4.238
V
VAGND
AGND
1.6 × Bandgap
2.016
2.081
2.150
V
VREFLO
Ref Low
VSS
VSS + 0.004
VSS + 0.018
V
Document Number: 38-12013 Rev. *S
VSS
VSS
VSS
Page 29 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 22. 3.3-V DC Analog Reference Specifications
Reference
ARF_CR[5:3]
Reference Power
Settings
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b000
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Symbol Reference
Description
Min
Typ
Max
Unit
VDD/2 + BandGap
VDD/2 + 1.225
VDD/2 + 1.292
VDD/2 + 1.361
V
VDD/2
VDD/2 – 0.067
VDD/2 – 0.002
VDD/2 + 0.063
V
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
VDD/2 – BandGap
VDD/2 – 1.35
VDD/2 – 1.293
VDD/2 – 1.210
V
VREFHI
Ref High
VDD/2 + BandGap
VDD/2 + 1.218
VDD/2 + 1.294
VDD/2 + 1.370
V
VAGND
AGND
VDD/2
VDD/2 – 0.038
VDD/2 – 0.001
VDD/2 + 0.035
V
VREFLO
Ref Low
VDD/2 – BandGap
VDD/2 – 1.329
VDD/2 – 1.296
VDD/2 – 1.259
V
VREFHI
Ref High
VDD/2 + BandGap
VDD/2 + 1.221
VDD/2 + 1.294
VDD/2 + 1.366
V
VAGND
AGND
VDD/2
VDD/2 – 0.050
VDD/2 – 0.002
VDD/2 + 0.046
V
VREFLO
Ref Low
VDD/2 – BandGap
VDD/2 – 1.331
VDD/2 – 1.296
VDD/2 – 1.260
V
VREFHI
Ref High
VDD/2 + BandGap
VDD/2 + 1.226
VDD/2 + 1.295
VDD/2 + 1.365
V
VAGND
AGND
VDD/2
VDD/2 – 0.028
VDD/2 – 0.001
VDD/2 + 0.025
V
VREFLO
Ref Low
VDD/2 – BandGap
VDD/2 – 1.329
VDD/2 – 1.297
VDD/2 – 1.262
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4]
= VDD/2, P2[6] =
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.098
0.018
0.055
V
VAGND
AGND
VREFLO
Ref Low
P2[4] – P2[6] (P2[4] P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
= VDD/2, P2[6] =
0.055
0.013
0.086
VREFHI
Ref High
P2[4] + P2[6] (P2[4] P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
= VDD/2, P2[6] =
0.082
0.011
0.050
0.5 V)
RefPower = High
Opamp bias = High
P2[4]
P2[4]
P2[4]
P2[4]
–
V
0.5 V)
V
0.5 V)
RefPower = High
Opamp bias = Low
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
P2[4]
P2[4]
P2[4]
P2[4]
P2[4] – P2[6] (P2[4] P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
= VDD/2, P2[6] =
0.037
0.006
0.054
–
V
0.5 V)
0b001
P2[4] + P2[6] (P2[4] P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
= VDD/2, P2[6] =
0.079
0.012
0.047
V
0.5 V)
RefPower = Med
Opamp bias = High
P2[4]
P2[4]–P2[6] (P2[4]
= VDD/2, P2[6] =
P2[4]
P2[4]
P2[4]
–
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.038
0.006
0.057
V
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.080
0.008
0.055
V
0.5 V)
P2[4]+P2[6] (P2[4]
= VDD/2, P2[6] =
0.5 V)
RefPower = Med
Opamp bias = Low
P2[4]
P2[4]–P2[6] (P2[4]
= VDD/2, P2[6] =
P2[4]
P2[4]
P2[4]
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.032
0.003
0.042
–
V
0.5 V)
Document Number: 38-12013 Rev. *S
Page 30 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 22. 3.3-V DC Analog Reference Specifications (continued)
Reference
ARF_CR[5:3]
Reference Power
Settings
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b010
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Symbol Reference
Description
Min
Typ
Max
Unit
VDD – 0.06
VDD – 0.010
VDD
V
VDD/2 – 0.05
VDD/2 – 0.002
VDD/2 + 0.040
V
VREFHI
Ref High
VAGND
AGND
VREFLO
Ref Low
Vss
Vss
Vss + 0.009
Vss + 0.056
V
VREFHI
Ref High
VDD
VDD – 0.060
VDD – 0.006
VDD
V
VAGND
AGND
VDD/2 – 0.028
VDD/2 – 0.001
VDD/2 + 0.025
V
VREFLO
Ref Low
Vss
Vss
Vss + 0.005
Vss + 0.034
V
VREFHI
Ref High
VDD
VDD – 0.058
VDD – 0.008
VDD
V
VAGND
AGND
VDD/2 – 0.037
VDD/2 – 0.002
VDD/2 + 0.033
V
VREFLO
Ref Low
Vss
Vss
Vss + 0.007
Vss + 0.046
V
VREFHI
Ref High
VDD
VDD – 0.057
VDD – 0.006
VDD
V
VAGND
AGND
VDD/2 – 0.025
VDD/2 – 0.001
VDD/2 + 0.022
V
VDD
VDD/2
VDD/2
VDD/2
VDD/2
VREFLO
Ref Low
0b011
All power settings.
Not allowed for 3.3 V
–
–
–
Vss
–
Vss + 0.004
–
Vss + 0.030
–
V
–
0b100
All power settings.
Not allowed for 3.3 V
–
–
–
–
–
–
–
VREFHI
Ref High
P2[4] + 1.213
P2[4] + 1.291
P2[4] + 1.367
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
V
VREFLO
Ref Low
P2[4] – BandGap
(P2[4] = VDD/2)
P2[4] – 1.333
P2[4] – 1.294
P2[4] – 1.208
V
VREFHI
Ref High
P2[4] + BandGap
(P2[4] = VDD/2)
P2[4] + 1.217
P2[4] + 1.294
P2[4] + 1.368
V
P2[4]
P2[4]
P2[4]
V
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b101
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
Vss
P2[4] + BandGap
(P2[4] = VDD/2)
P2[4]
VAGND
AGND
VREFLO
Ref Low
P2[4] – BandGap
(P2[4] = VDD/2)
P2[4] – 1.320
P2[4] – 1.296
P2[4] – 1.261
V
VREFHI
Ref High
P2[4] + BandGap
(P2[4] = VDD/2)
P2[4] + 1.217
P2[4] + 1.294
P2[4] + 1.369
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
V
VREFLO
Ref Low
P2[4] – BandGap
(P2[4] = VDD/2)
P2[4] – 1.322
P2[4] – 1.297
P2[4] – 1.262
V
VREFHI
Ref High
P2[4] + BandGap
(P2[4] = VDD/2)
P2[4] + 1.219
P2[4] + 1.295
P2[4] + 1.37
V
P2[4]
P2[4]
P2[4]
V
P2[4] – 1.324
P2[4] – 1.297
P2[4] – 1.262
V
VAGND
AGND
VREFLO
Ref Low
Document Number: 38-12013 Rev. *S
P2[4]
P2[4]
P2[4]
P2[4] – BandGap
(P2[4] = VDD/2)
Page 31 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 22. 3.3-V DC Analog Reference Specifications (continued)
Reference
ARF_CR[5:3]
Reference Power
Settings
RefPower = High
Opamp bias = High
RefPower = High
Opamp bias = Low
0b110
RefPower = Med
Opamp bias = High
RefPower = Med
Opamp bias = Low
0b111
Symbol Reference
VREFHI
Ref High
VAGND
AGND
Description
Min
Typ
Max
Unit
2 × BandGap
2.507
2.598
2.698
V
BandGap
1.203
1.307
1.424
V
Vss
Vss + 0.012
Vss + 0.067
V
VREFLO
Ref Low
Vss
VREFHI
Ref High
2 × BandGap
2.516
2.598
2.683
V
VAGND
AGND
BandGap
1.241
1.303
1.376
V
VREFLO
Ref Low
Vss
Vss
Vss + 0.007
Vss + 0.040
V
VREFHI
Ref High
2 × BandGap
2.510
2.599
2.693
V
VAGND
AGND
BandGap
1.240
1.305
1.374
V
VREFLO
Ref Low
Vss
Vss
Vss + 0.008
Vss + 0.048
V
VREFHI
Ref High
2 × BandGap
2.515
2.598
2.683
V
BandGap
1.258
1.302
1.355
V
Vss
–
Vss + 0.005
–
Vss + 0.03
–
V
–
VAGND
AGND
VREFLO
Ref Low
–
–
All power settings.
Not allowed for 3.3 V.
Vss
–
DC Analog PSoC Block Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 23. DC Analog PSoC Block Specifications
Symbol
RCT
CSC
Description
Resistor unit value (continuous time)
Capacitor unit value (switch cap)
Document Number: 38-12013 Rev. *S
Min
–
–
Typ
12.2
80
Max
–
–
Unit
kΩ
fF
Notes
Page 32 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
DC POR, SMP, and LVD Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 24. DC POR, SMP, and LVD Specifications
Symbol
VPPOR0R
VPPOR1R
VPPOR2R
VPPOR0
VPPOR1
VPPOR2
VPH0
VPH1
VPH2
VLVD0
VLVD1
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
VLVD7
VPUMP0
VPUMP1
VPUMP2
VPUMP3
VPUMP4
VPUMP5
VPUMP6
VPUMP7
Description
VDD value for PPOR trip (positive ramp)
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
VDD value for PPOR trip (negative ramp)
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
PPOR hysteresis
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
VDD value for LVD trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
VDD value for SMP trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
Min
Typ
Max
Units
–
2.91
4.39
4.55
–
V
V
V
–
2.82
4.39
4.55
–
V
V
V
–
–
–
92
0
0
–
–
–
mV
mV
mV
2.86
2.96
3.07
3.92
4.39
4.55
4.63
4.72
2.92
3.02
3.13
4.00
4.48
4.64
4.73
4.81
2.98[11]
3.08
3.20
4.08
4.57
4.74[12]
4.82
4.91
V
V
V
V
V
V
V
V
2.96
3.03
3.18
4.11
4.55
4.63
4.72
4.90
3.02
3.10
3.25
4.19
4.64
4.73
4.82
5.00
3.08
3.16
3.32
4.28
4.74
4.82
4.91
5.10
V
V
V
V
V
V
V
V
Notes
Notes
11. Always greater than 50 mV above PPOR (PORLEV = 00) for falling supply.
12. Always greater than 50 mV above PPOR (PORLEV = 10) for falling supply.
Document Number: 38-12013 Rev. *S
Page 33 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
DC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 25. DC Programming Specifications
Symbol
VDDP
VDDLV
VDDHV
Description
Min
Typ
Units
Notes
4.5
5
5.5
V
This specification applies
to the functional
requirements of external
programmer tools.
3
3.1
3.2
V
This specification applies
to the functional
requirements of external
programmer tools.
5.3
V
This specification applies
to the functional
requirements of external
programmer tools.
5.25
V
This specification applies
to this device when it is
executing internal flash
writes.
Low VDD for verify
High VDD for verify
5.1
VDDIWRITE
Max
VDD for programming and erase
5.2
Supply voltage for flash write operation
3.15
IDDP
Supply current during programming or verify
–
10
30
mA
VILP
Input low voltage during programming or verify
–
–
0.8
V
VIHP
Input high voltage during programming or verify
2.2
–
–
V
IILP
Input current when applying Vilp to P1[0] or P1[1]
during programming or verify
–
–
0.2
mA
Driving internal pull-down
resistor
IIHP
Input current when applying Vihp to P1[0] or P1[1]
during programming or verify
–
–
1.5
mA
Driving internal pull-down
resistor
VOLV
Output low voltage during programming or verify
–
–
VSS + 0.75
V
VOHV
Output high voltage during programming or verify
VDD – 1.0
–
VDD
V
[13]
–
–
–
Erase/write cycles per
block
Erase/write cycles
FlashENPB
Flash endurance (per block)
50,000
FlashENT
Flash endurance (total)[14]
1,800,000
–
–
–
FlashDR
Flash data retention
10
–
–
Years
DC I2C Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 26. DC I2C Specifications
Parameter
VILI2C[15]
VIHI2C[15]
Description
Input low level
Input high level
Min
Typ
Max
Units
–
–
0.7 × VDD
Notes
–
0.3 × VDD
V
–
0.25 × VDD
V
4.75 V ≤ VDD ≤ 5.25 V
–
–
V
3.0 V ≤ VDD ≤ 5.25 V
3.0 V ≤ VDD ≤ 3.6 V
Notes
13. The 50,000 cycle flash endurance per block is only guaranteed if the flash is operating within one voltage range. Voltage ranges are 3.0 V to 3.6 V and 4.75 V to 5.25 V.
14. A maximum of 36 × 50,000 block endurance cycles is allowed. This may be balanced between operations on 36 × 1 blocks of 50,000 maximum cycles each,
36 × 2 blocks of 25,000 maximum cycles each, or 36 × 4 blocks of 12,500 maximum cycles each (to limit the total number of cycles to 36 × 50,000 and that no
single block ever sees more than 50,000 cycles).
For the full industrial range, the user must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs application note Design Aids – Reading and Writing PSoC® Flash – AN2015 for more information.
15. All GPIOs meet the DC GPIO VIL and VIH specifications found in the DC GPIO specifications sections.The I2C GPIO pins also meet the mentioned specs.
Document Number: 38-12013 Rev. *S
Page 34 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
AC Electrical Characteristics
AC Chip-Level Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Note See the individual user module datasheets for information on maximum frequencies for user modules.
Table 27. AC Chip-Level Specifications
Symbol
Description
FIMO24
Internal main oscillator (IMO) frequency for 24
MHz
FIMO6
IMO frequency for 6 MHz
FCPU1
CPU frequency (5 V Nominal)
Min
Typ
Max
[16,17]
Units
Notes
23.4
24
24.6
MHz
Trimmed for 5 V or 3.3 V
operation using factory trim
values. See Figure 10 on
page 19. SLIMO Mode = 0.
5.5
6
6.5[16,17]
MHz
Trimmed for 5 V or 3.3 V
operation using factory trim
values. See Figure 10 on
page 19. SLIMO Mode = 1.
0.0914
24
24.6[16]
MHz
SLIMO Mode = 0.
[17]
FCPU2
CPU frequency (3.3 V Nominal)
0.0914
12
MHz
SLIMO Mode = 0.
F48M
Digital PSoC block frequency
0
48
49.2[16,18]
12.3
MHz
Refer to AC Digital Block
Specifications on page 40.
F24M
Digital PSoC block frequency
0
24
24.6[18]
MHz
F32K1
Internal low speed oscillator frequency
15
32
64
kHz
F32K2
External crystal oscillator
–
32.768
–
kHz
Accuracy is capacitor and
crystal dependent. 50%
duty cycle
F32K_U
Internal low speed oscillator (ILO) untrimmed
frequency
5
–
100
kHz
After a reset and before the
M8C starts to run, the ILO is
not trimmed. See the
System Resets section of
the PSoC Technical
Reference Manual for
details on this timing
FPLL
PLL frequency
–
23.986
–
MHz
A multiple (x732) of crystal
frequency
TPLLSLEW
PLL lock time
0.5
–
10
ms
TPLLSLEWLOW
PLL lock time for low gain setting
0.5
–
50
ms
TOS
External crystal oscillator startup to 1%
–
250
500
ms
TOSACC
External crystal oscillator startup to 100 ppm
–
300
600
ms
TXRST
External reset pulse width
10
–
–
μs
DC24M
24 MHz duty cycle
40
50
60
%
DCILO
Internal low speed oscillator duty cycle
20
50
80
%
Step24M
24 MHz trim step size
–
50
–
kHz
Fout48M
48 MHz output frequency
46.8
48.0
49.2[16, 17]
MHz
The crystal oscillator
frequency is within 100 ppm
of its final value by the end
of the TOSACC period.
Correct operation assumes
a properly loaded 1 µW
maximum drive level 32.768
kHz crystal.
3.0 V ≤ VDD ≤ 5.5 V, –40 °C
≤ TA ≤ 85 °C.
Trimmed. Using factory trim
values
Notes
16. 4.75 V < VDD < 5.25 V.
17. 3.0 V < VDD < 3.6 V. See application note Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 for information on trimming for operation at 3.3 V.
18. See the individual user module datasheets for information on maximum frequencies for user modules
Document Number: 38-12013 Rev. *S
Page 35 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 27. AC Chip-Level Specifications (continued)
Min
Typ
Max
Units
FMAX
Symbol
Maximum frequency of signal on row input or
row output.
–
–
12.3
MHz
SRPOWER_UP
Power supply slew rate
–
–
250
V/ms
TPOWERUP
Time from end of POR to CPU executing code
–
16
100
ms
Power-up from 0 V. See the
System Resets section of
the PSoC Technical
Reference Manual
tjit_IMO[19]
24 MHz IMO cycle-to-cycle jitter (RMS)
–
200
700
ps
N = 32
24 MHz IMO long term N cycle-to-cycle jitter
(RMS)
–
300
900
24 MHz IMO period jitter (RMS)
–
100
400
24 MHz IMO cycle-to-cycle jitter (RMS)
–
200
800
ps
N = 32
24 MHz IMO long term N cycle-to-cycle jitter
(RMS)
–
300
1200
24 MHz IMO period jitter (RMS)
–
100
700
tjit_PLL [19]
Description
Notes
VDD slew rate during
power-up
Figure 12. PLL Lock Timing Diagram
PLL
Enable
TPLLSLEW
24 MHz
FPLL
PLL
Gain
0
Figure 13. PLL Lock for Low Gain Setting Timing Diagram
PLL
Enable
TPLLSLEWLOW
24 MHz
FPLL
PLL
Gain
1
Figure 14. External Crystal Oscillator Startup Timing Diagram
32K
Select
32 kHz
TOS
F32K2
Note
19. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 38-12013 Rev. *S
Page 36 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
AC General Purpose I/O Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 28. AC GPIO Specifications
Symbol
FGPIO
tRiseF
tFallF
tRiseS
tFallS
Description
GPIO operating frequency
Rise time, normal strong mode, Cload = 50 pF
Fall time, normal strong mode, Cload = 50 pF
Rise time, slow strong mode, Cload = 50 pF
Fall time, slow strong mode, Cload = 50 pF
Min
0
3
2
10
10
Typ
–
–
–
27
22
Max
12.3
18
18
–
–
Unit
MHz
ns
ns
ns
ns
Notes
Normal strong mode
VDD = 4.75 to 5.25 V, 10% to 90%
VDD = 4.75 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
Figure 15. GPIO Timing Diagram
90%
GPIO
Pin
Output
Voltage
10%
TRiseF
TRiseS
TFallF
TFallS
AC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Settling times, slew rates, and gain bandwidth are based on the analog continuous time PSoC block.
Power = High and Opamp bias = High is not supported at 3.3 V.
Table 29. 5-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time to 0.1% for a 1 V step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = High
Falling settling time to 0.1% for a 1 V step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = High
Rising slew rate (20% to 80%) of a 1 V step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = High
Falling slew rate (20% to 80%) of a 1 V step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = High
Gain bandwidth product
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Power = High, Opamp bias = High
Noise at 1 kHz (Power = Medium, Opamp bias = High)
Document Number: 38-12013 Rev. *S
Min
Typ
Max
Unit
–
–
–
–
–
–
3.9
0.72
0.62
µs
µs
µs
–
–
–
–
–
–
5.9
0.92
0.72
µs
µs
µs
0.15
1.7
6.5
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.01
0.5
4.0
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.75
3.1
5.4
–
–
–
–
100
–
–
–
–
MHz
MHz
MHz
nV/rt-Hz
Page 37 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 30. 3.3-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time to 0.1% of a 1 V Step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Falling settling time to 0.1% of a 1 V Step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Rising slew rate (20% to 80%) of a 1 V Step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Falling slew rate (20% to 80%) of a 1 V Step (10 pF load, unity gain)
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Gain bandwidth product
Power = Low, Opamp bias = Low
Power = Medium, Opamp bias = High
Noise at 1 kHz (Power = Medium, Opamp bias = High)
Min
Typ
Max
Units
–
–
–
–
3.92
0.72
µs
µs
–
–
–
–
5.41
0.72
µs
µs
0.31
2.7
–
–
–
–
V/µs
V/µs
0.24
1.8
0.67
2.8
–
–
–
–
–
–
–
–
V/µs
V/µs
MHz
MHz
–
100
–
nV/rt-Hz
When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up
to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1 K resistance and the external capacitor.
Figure 16. Typical AGND Noise with P2[4] Bypass
nV/rtHz
10000
0
0.01
0.1
1.0
10
1000
100
0.001
0.01
0.1 Freq (kHz)
1
10
100
At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high
frequencies, increased power level reduces the noise spectrum level.
Document Number: 38-12013 Rev. *S
Page 38 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 17. Typical Opamp Noise
nV/rtHz
10000
PH_BH
PH_BL
PM_BL
PL_BL
1000
100
10
0.001
0.01
0.1
Freq (kHz)
1
10
100
AC Low-Power Comparator Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, or 2.4 V to 3.0 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical
parameters apply to 5 V at 25 °C and are for design guidance only.
Table 31. AC Low-Power Comparator Specifications
Symbol
tRLPC
Description
LPC response time
Document Number: 38-12013 Rev. *S
Min Typ Max Unit
–
–
50
µs
Notes
≥ 50 mV overdrive comparator reference set within
VREFLPC
Page 39 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
AC Digital Block Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 32. AC Digital Block Specifications
Function
All functions
Timer
Description
Min
Typ
Max
Unit
VDD ≥ 4.75 V
–
–
49.2
MHz
VDD < 4.75 V
–
–
24.6
MHz
–
–
49.2
MHz
Input clock frequency
No capture, VDD ≥ 4.75 V
No capture, VDD < 4.75 V
–
–
24.6
MHz
With capture
–
–
24.6
MHz
50[20]
–
–
ns
No enable input, VDD ≥ 4.75 V
–
–
49.2
MHz
No enable input, VDD < 4.75 V
–
–
24.6
MHz
With enable input
–
–
24.6
MHz
50[20]
–
–
ns
20
Capture pulse width
Counter
Input clock frequency
Enable input pulse width
Dead Band
Notes
Block input clock frequency
Kill pulse width
Asynchronous restart mode
–
–
ns
Synchronous restart mode
[20]
50
–
–
ns
Disable mode
50[20]
–
–
ns
Input clock frequency
CRCPRS
(PRS Mode)
VDD ≥ 4.75 V
–
–
49.2
MHz
VDD < 4.75 V
–
–
24.6
MHz
VDD ≥ 4.75 V
–
–
49.2
MHz
VDD < 4.75 V
–
–
24.6
MHz
Input clock frequency
CRCPRS
(CRC Mode)
Input clock frequency
–
–
24.6
MHz
SPIM
Input clock frequency
–
–
8.2
MHz
The SPI serial clock (SCLK) frequency is equal to the
input clock frequency divided by 2
SPIS
Input clock (SCLK) frequency
–
–
4.1
MHz
The input clock is the SPI SCLK in SPIS mode
Width of SS_negated between
transmissions
50[20]
–
–
ns
Transmitter
Receiver
Input clock frequency
VDD ≥ 4.75 V, 2 stop bits
–
–
49.2
MHz
VDD ≥ 4.75 V, 1 stop bit
–
–
24.6
MHz
VDD < 4.75 V
–
–
24.6
MHz
–
–
49.2
MHz
Input clock frequency
VDD ≥ 4.75 V, 2 stop bits
VDD ≥ 4.75 V, 1 stop bit
–
–
24.6
MHz
VDD < 4.75 V
–
–
24.6
MHz
The baud rate is equal to the input clock frequency
divided by 8
The baud rate is equal to the input clock frequency
divided by 8
Note
20. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
Document Number: 38-12013 Rev. *S
Page 40 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
AC Analog Output Buffer Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 33. 5-V AC Analog Output Buffer Specifications
Symbol
tROB
tSOB
SRROB
SRFOB
BWOB
BWOB
Description
Rising settling time to 0.1%, 1 V Step, 100 pF load
Power = Low
Power = High
Falling settling time to 0.1%, 1 V step, 100 pF load
Power = Low
Power = High
Rising slew rate (20% to 80%), 1 V step, 100 pF load
Power = Low
Power = High
Falling slew rate (80% to 20%), 1 V step, 100 pF load
Power = Low
Power = High
Small signal bandwidth, 20 mVpp, 3 dB BW, 100 pF load
Power = Low
Power = High
Large signal bandwidth, 1 Vpp, 3 dB BW, 100 pF load
Power = Low
Power = High
Min
Typ
Max
Unit
–
–
–
–
4
4
µs
µs
–
–
–
–
3.4
3.4
µs
µs
0.5
0.5
–
–
–
–
V/µs
V/µs
0.55
0.55
–
–
–
–
V/µs
V/µs
0.8
0.8
–
–
–
–
MHz
MHz
300
300
–
–
–
–
kHz
kHz
Min
Typ
Max
Unit
–
–
–
–
4.7
4.7
µs
µs
–
–
–
–
4
4
µs
µs
0.36
0.36
–
–
–
–
V/µs
V/µs
0.40
0.40
–
–
–
–
V/µs
V/µs
0.7
0.7
–
–
–
–
MHz
MHz
200
200
–
–
–
–
kHz
kHz
Table 34. 3.3-V AC Analog Output Buffer Specifications
Symbol
tROB
tSOB
SRROB
SRFOB
BWOB
BWOB
Description
Rising settling time to 0.1%, 1 V Step, 100 pF load
Power = Low
Power = High
Falling settling time to 0.1%, 1 V Step, 100 pF load
Power = Low
Power = High
Rising slew rate (20% to 80%), 1 V Step, 100 pF load
Power = Low
Power = High
Falling slew rate (80% to 20%), 1 V Step, 100 pF load
Power = Low
Power = High
Small signal bandwidth, 20 mVpp, 3 dB BW, 100 pF load
Power = Low
Power = High
Large signal bandwidth, 1 Vpp, 3 dB BW, 100 pF load
Power = Low
Power = High
AC External Clock Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 35. 5-V AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Unit
FOSCEXT
Frequency
0.093
–
24.6
MHz
–
High period
20.6
–
5300
ns
–
Low period
20.6
–
–
ns
–
Power-up IMO to switch
150
–
–
ms
Document Number: 38-12013 Rev. *S
Page 41 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Table 36. 3.3-V AC External Clock Specifications
Symbol
Min
Typ
Max
Unit
Frequency with CPU clock divide by 1
0.093
–
12.3
MHz
FOSCEXT
Frequency with CPU clock divide by 2 or greater
0.186
–
24.6
MHz
–
High period with CPU clock divide by 1
41.7
–
5300
ns
–
Low period with CPU clock divide by 1
41.7
–
–
ns
–
Power-up IMO to switch
150
–
–
µs
FOSCEXT
Description
AC Programming Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 37. AC Programming Specifications
Symbol
Description
Min
Typ
Max
Unit
1
–
20
ns
–
Fall time of SCLK
1
–
20
ns
–
Data setup time to falling edge of SCLK
40
–
–
ns
–
tHSCLK
Data hold time from falling edge of SCLK
40
–
–
ns
–
FSCLK
Frequency of SCLK
0
–
8
MHz
–
tERASEB
Flash erase time (block)
–
10
–
ms
–
tWRITE
Flash block write time
–
40
–
ms
–
tDSCLK
Data out delay from falling edge of SCLK
–
–
45
ns
VDD > 3.6
tDSCLK3
Data out delay from falling edge of SCLK
–
–
50
ns
3.0 ≤ VDD ≤ 3.6
tERASEALL
Flash erase time (Bulk)
–
80
–
ms
Erase all blocks and
protection fields at once
tPROGRAM_HOT
Flash block erase + Flash block write time
–
–
100[21]
ms
0 °C ≤ Tj ≤ 100 °C
tPROGRAM_COLD
Flash block erase + Flash block write time
–
–
200[21]
ms
–40 °C ≤ Tj ≤ 0 °C
tRSCLK
Rise time of SCLK
tFSCLK
tSSCLK
Notes
Note
21. For the full industrial range, you must employ a temperature sensor user module (FlashTemp) and feed the result to the temperature argument before writing.
Refer to the Flash APIs application note Design Aids – Reading and Writing PSoC® Flash – AN2015 for more information.
Document Number: 38-12013 Rev. *S
Page 42 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
AC I2C Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 38. AC Characteristics of the I2C SDA and SCL Pins
Symbol
Standard Mode
Description
Fast Mode
Unit
Min
Max
Min
Max
0
100
0
400
kHz
FSCLI2C
SCL clock frequency
THDSTAI2C
Hold time (repeated) START condition. After this period, the first clock
pulse is generated.
4.0
–
0.6
–
µs
TLOWI2C
LOW period of the SCL clock
4.7
–
1.3
–
µs
THIGHI2C
HIGH period of the SCL clock
4.0
–
0.6
–
µs
TSUSTAI2C
Setup time for a repeated START condition
4.7
–
0.6
–
µs
THDDATI2C
Data hold time
0
–
0
–
µs
TSUDATI2C
Data setup time
250
–
100[22]
–
ns
TSUSTOI2C
Setup time for STOP condition
4.0
–
0.6
–
µs
TBUFI2C
Bus free time between a STOP and START condition
4.7
–
1.3
–
µs
TSPI2C
Pulse width of spikes are suppressed by the input filter.
–
–
0
50
ns
Figure 18. Definition for Timing for Fast/Standard Mode on the I2C Bus
I2C_SDA
TSUDATI2C
THDSTAI2C
TSPI2C
THDDATI2CTSUSTAI2C
TBUFI2C
I2C_SCL
THIGHI2C TLOWI2C
S
START Condition
TSUSTOI2C
Sr
Repeated START Condition
P
S
STOP Condition
Note
22. A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but the requirement tSU;DAT >= 250 ns must then be met. This is the automatic case
if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to the
SDA line trmax + tSU;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C-bus specification) before the SCL line is released.
Document Number: 38-12013 Rev. *S
Page 43 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Packaging Information
This section illustrates the packaging specifications for the CY8C29x66 PSoC device, along with the thermal impedances for each
package and the typical package capacitance on crystal pins.
Important Note Emulation tools may require a larger area on the target PCB than the chip's footprint. For a detailed description of
the emulation tools' dimensions, refer to the emulator pod drawings at http://www.cypress.com.
Packaging Dimensions
Figure 19. 28-Pin (300-Mil) Molded DIP
SEE LEAD END OPTION
14
1
DIMENSIONS IN INCHES[MM]
REFERENCE JEDEC MO-095
0.260[6.60]
0.295[7.49]
15
28
MIN.
MAX.
PACKAGE WEIGHT: 2.15gms
0.030[0.76]
0.080[2.03]
P28.3
PART #
STANDARD PKG.
PZ28.3
LEAD FREE PKG.
SEATING PLANE
1.345[34.16]
1.385[35.18]
0.290[7.36]
0.325[8.25]
0.120[3.05]
0.140[3.55]
0.140[3.55]
0.190[4.82]
0.115[2.92]
0.160[4.06]
0.015[0.38]
0.060[1.52]
0.090[2.28]
0.110[2.79]
0.009[0.23]
0.012[0.30]
0.055[1.39]
0.065[1.65]
0.015[0.38]
0.020[0.50]
3° MIN.
0.310[7.87]
0.385[9.78]
SEE LEAD END OPTION
LEAD END OPTION
(LEAD #1, 14, 15 & 28)
51-85014 *E
Document Number: 38-12013 Rev. *S
Page 44 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 20. 28-Pin (210-Mil) SSOP
51-85079 *E
Figure 21. 28-Pin (300-Mil) SOIC
51-85026 *F
Document Number: 38-12013 Rev. *S
Page 45 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 22. 44-Pin TQFP
51-85064 *E
Figure 23. 48-Pin (7 × 7 mm) QFN
SOLDERABLE
EXPOSED
PAD
001-12919 *C
Document Number: 38-12013 Rev. *S
Page 46 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 24. 48-Pin (300-Mil) SSOP
.020
24
1
0.395
0.420
0.292
0.299
25
DIMENSIONS IN INCHES MIN.
MAX.
48
0.620
0.630
0.088
0.092
0.095
0.110
0.025
BSC
SEATING PLANE
0.005
0.010
.010
GAUGE PLANE
0.004
0.008
0.0135
0.008
0.016
0°-8°
0.024
0.040
51-85061 *D
Figure 25. 48-Pin QFN 7 × 7 × 0.90 mm (Sawn Type)
001-13191 *E
Document Number: 38-12013 Rev. *S
Page 47 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Figure 26. 100-Pin TQFP
51-85048 *E
Important Note For information on the preferred dimensions for mounting the QFN packages, see the application note Application
Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages available at http://www.amkor.com.
Important Note Pinned vias for thermal conduction are not required for the low-power PSoC device.
Document Number: 38-12013 Rev. *S
Page 48 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Thermal Impedances
Capacitance on Crystal Pins
Table 39. Thermal Impedances per Package
Typical θJA[
Package
Table 40. Typical Package Capacitance on Crystal Pins
23]
Package
Package Capacitance
28-pin PDIP
69 °C/W
28-pin PDIP
3.5 pF
28-pin SSOP
94 °C/W
28-pin SSOP
2.8 pF
28-pin SOIC
67 °C/W
28-pin SOIC
2.7 pF
44-pin TQFP
60 °C/W
44-pin TQFP
2.6 pF
48-pin SSOP
69 °C/W
48-pin SSOP
3.3 pF
48-pin QFN[24]
28 °C/W
48-pin QFN
1.8 pF
100-pin TQFP
50 °C/W
100-pin TQFP
3.1 pF
Solder Reflow Specifications
Table 41 shows the solder reflow temperature limits that must not be exceeded.
Table 41. Solder Reflow Specifications
Package
Maximum Peak Temperature
(TC)
Maximum Time above
TC – 5 °C
28-pin PDIP
260 °C
30 seconds
28-pin SSOP
260 °C
30 seconds
28-pin SOIC
260 °C
30 seconds
44-pin TQFP
260 °C
30 seconds
48-pin SSOP
260 °C
30 seconds
48-pin QFN
260 °C
30 seconds
100-pin TQFP
260 °C
30 seconds
Notes
23. TJ = TA + POWER × θJA.
24. To achieve the thermal impedance specified for the QFN package, refer to the application notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF)
Packages available at http://www.amkor.com.
Document Number: 38-12013 Rev. *S
Page 49 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Development Tool Selection
This section presents the development tools available for all
current PSoC device families including the CY8C29x66 family.
Evaluation Tools
Software
All evaluation tools can be purchased from the Cypress online
store.
PSoC Designer™
CY3210-MiniProg1
At the core of the PSoC development software suite is PSoC
Designer, used to generate PSoC firmware applications. PSoC
Designer is available free of charge at http://www.cypress.com
and includes a free C compiler.
The CY3210-MiniProg1 kit allows a user to program PSoC
devices via the MiniProg1 programming unit. The MiniProg is a
small, compact prototyping programmer that connects to the PC
via a provided USB 2.0 cable. The kit includes:
■
MiniProg programming unit
■
MiniEval socket programming and evaluation board
■
28-pin CY8C29466-24PXI PDIP PSoC device sample
■
28-pin CY8C27443-24PXI PDIP PSoC device sample
■
PSoC Designer software CD
■
Getting Started guide
Development Kits
■
USB 2.0 cable
All development kits can be purchased from the Cypress Online
Store.
CY3210-PSoCEval1
PSoC Programmer
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can operate
directly from PSoC Designer or PSoC Express. PSoC
Programmer software is compatible with both PSoC ICE-Cube
In-Circuit Emulator and PSoC MiniProg. PSoC programmer is
available free of charge at http://www.cypress.com.
CY3215-DK Basic Development Kit
The CY3215-DK is for prototyping and development with PSoC
Designer. This kit supports in-circuit emulation and the software
interface allows users to run, halt, and single step the processor
and view the content of specific memory locations. Advance
emulation features also supported through PSoC Designer. The
kit includes:
■
PSoC Designer software CD
■
ICE-Cube In-Circuit Emulator
■
ICE Flex-Pod for CY8C29x66 family
■
Cat-5 adapter
■
Mini-Eval programming board
■
110 ~ 240 V power supply, Euro-Plug adapter
■
iMAGEcraft C compiler
■
ISSP cable
■
USB 2.0 cable and Blue Cat-5 cable
■
Two CY8C29466-24PXI 28-PDIP chip samples
Document Number: 38-12013 Rev. *S
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, and plenty of breadboarding space to meet all of your evaluation needs. The kit
includes:
■
Evaluation board with LCD module
■
MiniProg programming unit
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Sample (2)
■
PSoC Designer software CD
■
Getting Started guide
■
USB 2.0 cable
CY3214-PSoCEvalUSB
The CY3214-PSoCEvalUSB evaluation kit features a
development board for the CY8C24794-24LFXI PSoC device.
Special features of the board include both USB and capacitive
sensing development and debugging support. This evaluation
board also includes an LCD module, potentiometer, LEDs, an
enunciator and plenty of bread boarding space to meet all of your
evaluation needs. The kit includes:
■
PSoCEvalUSB board
■
LCD module
■
MIniProg programming unit
■
Mini USB cable
■
PSoC Designer and example projects CD
■
Getting Started guide
■
Wire pack
Page 50 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Device Programmers
All device programmers can be purchased from the Cypress
Online Store.
CY3216 Modular Programmer
The CY3216 Modular Programmer kit features a modular
programmer and the MiniProg1 programming unit. The modular
programmer includes three programming module cards and
supports multiple Cypress products. The kit includes:
CY3207ISSP In-System Serial Programmer (ISSP)
The CY3207ISSP is a production programmer. It includes
protection circuitry and an industrial case that is more robust than
the MiniProg in a production-programming environment.
Note CY3207ISSP needs special software and is not compatible
with PSoC Programmer. The kit includes:
■
CY3207 programmer unit
■
Modular programmer base
■
PSoC ISSP software CD
■
Three programming module cards
■
110 ~ 240 V power supply, Euro-Plug adapter
■
MiniProg programming unit
■
USB 2.0 cable
■
PSoC Designer software CD
■
Getting Started guide
■
USB 2.0 cable
Accessories (Emulation and Programming)
Table 42. Emulation and Programming Accessories
Part #
Pin
Package
Flex-Pod Kit[25]
Foot Kit[26]
CY8C29466-24PXI
28-pin PDIP
CY3250-29XXX
CY3250-28PDIP-FK
CY8C29466-24PVXI
28-pin SSOP
CY3250-29XXX
CY3250-28SSOP-FK
CY8C29466-24SXI
28-pin SOIC
CY3250-29XXX
CY3250-28SOIC-FK
CY8C29566-24AXI
44-pin TQFP
CY3250-29XXX
CY3250-44TQFP-FK
CY8C29666-24PVXI
48-pin SSOP
CY3250-29XXX
CY3250-48SSOP-FK
CY8C29666-24LTXI
48-pin QFN
CY3250-29XXXQFN
CY3250-48QFN-FK
CY8C29866-24AXI
100-pin TQFP CY3250-29XXX
Adapter[27]
Adapters can be found at
http://www.emulation.com.
CY3250-100TQFP-FK
Notes
25. Flex-Pod kit includes a practice flex-pod and a practice PCB, in addition to two flex-pods.
26. Foot kit includes surface mount feet that can be soldered to the target PCB.
27. Programming adapter converts non-DIP package to DIP footprint. Specific details and ordering information for each of the adapters can be found at
http://www.emulation.com
Document Number: 38-12013 Rev. *S
Page 51 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Ordering Information
RAM
(KB)
Switch Mode
Pump
Temperature
Range
Digital PSoC
Blocks
Analog PSoC
Blocks
Digital I/O
Pins
Analog
Inputs
Analog
Outputs
XRES Pin
CY8C29466-24PXI
CY8C29466-24PVXI
32
32
2
2
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
16
16
12
12
24
24
12
12
4
4
Yes
Yes
CY8C29466-24PVXIT
32
2
Yes
–40 °C to +85 °C
16
12
24
12
4
Yes
CY8C29466-24SXI
32
2
Yes
–40 °C to +85 °C
16
12
24
12
4
Yes
CY8C29466-24SXIT
32
2
Yes
–40 °C to +85 °C
16
12
24
12
4
Yes
CY8C29566-24AXI
32
2
Yes
–40 °C to +85 °C
16
12
40
12
4
Yes
CY8C29566-24AXIT
32
2
Yes
–40 °C to +85 °C
16
12
40
12
4
Yes
CY8C29666-24PVXI
32
2
Yes
–40 °C to +85 °C
16
12
44
12
4
Yes
CY8C29666-24PVXIT
32
2
Yes
–40 °C to +85 °C
16
12
44
12
4
Yes
CY8C29866-24AXI
CY8C29000-24AXI
32
32
2
2
Yes
Yes
–40 °C to +85 °C
–40 °C to +85 °C
16
16
12
12
64
64
12
12
4
4
Yes
Yes
CY8C29666-24LTXI
32
2
Yes
–40 °C to +85 °C
16
12
44
12
4
Yes
CY8C29666-24LTXIT
32
2
Yes
–40 °C to +85 °C
16
12
44
12
4
Yes
Package
Ordering
Code
Flash
(KB)
The following table lists the CY8C29x66 PSoC device’s key package features and ordering codes.
28-pin (300-mil) DIP
28-pin (210-mil) SSOP
28-pin (210-mil) SSOP
(Tape and Reel)
28-pin (300-mil) SOIC
28-pin (300-mil) SOIC
(Tape and Reel)
44-pin TQFP
44-pin TQFP
(Tape and Reel)
48-pin (300-mil) SSOP
48-pin (300-mil) SSOP
(Tape and Reel)
100-Pin TQFP
100-Pin OCD TQFP[28]
48-Pin (7 × 7 × 1.0 mm)
QFN (Sawn)
48-Pin (7 × 7 × 1.0 mm)
QFN (Sawn)
Note For Die sales information, contact a local Cypress sales office or field applications engineer (FAE).
Ordering Code Definitions
CY 8 C 29 xxx-SPxx
Package Type:
PX = PDIP Pb-free
SX = SOIC Pb-free
PVX = SSOP Pb-free
LFX/LKX/LTX/LQX/LCX = QFN Pb-free
AX = TQFP Pb-free
Thermal Rating:
C = Commercial
I = Industrial
E = Extended
Speed: 24 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = Cypress PSoC
Company ID: CY = Cypress
Note
28. This part may be used for in-circuit debugging. It is NOT available for production.
Document Number: 38-12013 Rev. *S
Page 52 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Acronyms
Acronyms Used
Table 43 lists the acronyms that are used in this document.
Table 43. Acronyms Used in this Datasheet
Acronym
AC
ADC
API
CMOS
CPU
CRC
CT
DAC
DC
Description
Acronym
Description
alternating current
MIPS
million instructions per second
analog-to-digital converter
OCD
on-chip debug
application programming interface
PCB
printed circuit board
complementary metal oxide semiconductor
PDIP
plastic dual-in-line package
central processing unit
PGA
programmable gain amplifier
cyclic redundancy check
PLL
phase-locked loop
continuous time
POR
power on reset
digital-to-analog converter
direct current
PPOR
PRS
precision power on reset
pseudo-random sequence
DTMF
dual-tone multi-frequency
PSoC®
ECO
external crystal oscillator
PWM
pulse width modulator
electrically erasable programmable read-only
memory
QFN
quad flat no leads
EEPROM
GPIO
Programmable System-on-Chip
general purpose I/O
RTC
real time clock
ICE
in-circuit emulator
SAR
successive approximation
IDE
integrated development environment
SC
switched capacitor
ILO
internal low speed oscillator
SMP
switch mode pump
IMO
internal main oscillator
SOIC
small-outline integrated circuit
I/O
input/output
SPI
serial peripheral interface
IrDA
infrared data association
SRAM
static random access memory
ISSP
in-system serial programming
SROM
supervisory read only memory
LCD
liquid crystal display
SSOP
shrink small-outline package
LED
light-emitting diode
TQFP
thin quad flat pack
LPC
low power comparator
UART
universal asynchronous reciever / transmitter
LVD
low voltage detect
USB
universal serial bus
MAC
multiply-accumulate
WDT
watchdog timer
MCU
microcontroller unit
XRES
external reset
Reference Documents
CY8CPLC20, CY8CLED16P01, CY8C29x66, CY8C27x43, CY8C24x94, CY8C24x23, CY8C24x23A, CY8C22x13, CY8C21x34,
CY8C21x23, CY7C64215, CY7C603xx, CY8CNP1xx, and CYWUSB6953 PSoC® Programmable System-on-Chip Technical
Reference Manual (TRM) (001-14463)
Design Aids – Reading and Writing PSoC® Flash - AN2015 (001-40459)
Adjusting PSoC® Trims for 3.3 V and 2.7 V Operation – AN2012 (001-17397)
Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 (001-14503)
Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages – available at http://www.amkor.com.
Document Number: 38-12013 Rev. *S
Page 53 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Document Conventions
Units of Measure
Table 44 lists the unit sof measures.
Table 44. Units of Measure
Symbol
dB
°C
fF
pF
kHz
MHz
rt-Hz
kΩ
Ω
µA
mA
nA
pA
µs
Unit of Measure
decibels
degree Celsius
femto farad
picofarad
kilohertz
megahertz
root hertz
kilohm
ohm
microampere
milliampere
nanoampere
pikoampere
microsecond
Symbol
ms
ns
ps
µV
mV
mVpp
nV
V
µW
W
mm
ppm
%
Unit of Measure
millisecond
nanosecond
picosecond
microvolts
millivolts
millivolts peak-to-peak
nanovolts
volts
microwatts
watt
millimeter
parts per million
percent
Numeric Conventions
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, 01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’, ‘b’, or 0x are decimals.
Glossary
active high
1. A logic signal having its asserted state as the logic 1 state.
2. A logic signal having the logic 1 state as the higher voltage of the two states.
analog blocks
The basic programmable opamp circuits. These are SC (switched capacitor) and CT (continuous
time) blocks. These blocks can be interconnected to provide ADCs, DACs, multi-pole filters, gain
stages, and much more.
analog-to-digital
(ADC)
A device that changes an analog signal to a digital signal of corresponding magnitude. Typically,
an ADC converts a voltage to a digital number. The digital-to-analog (DAC) converter performs
the reverse operation.
Application
programming
interface (API)
A series of software routines that comprise an interface between a computer application and
lower level services and functions (for example, user modules and libraries). APIs serve as
building blocks for programmers that create software applications.
asynchronous
A signal whose data is acknowledged or acted upon immediately, irrespective of any clock signal.
bandgap
reference
A stable voltage reference design that matches the positive temperature coefficient of VT with
the negative temperature coefficient of VBE, to produce a zero temperature coefficient (ideally)
reference.
bandwidth
1. The frequency range of a message or information processing system measured in hertz.
2. The width of the spectral region over which an amplifier (or absorber) has substantial gain (or
loss); it is sometimes represented more specifically as, for example, full width at half maximum.
Document Number: 38-12013 Rev. *S
Page 54 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Glossary (continued)
bias
1. A systematic deviation of a value from a reference value.
2. The amount by which the average of a set of values departs from a reference value.
3. The electrical, mechanical, magnetic, or other force (field) applied to a device to establish a
reference level to operate the device.
block
1. A functional unit that performs a single function, such as an oscillator.
2. A functional unit that may be configured to perform one of several functions, such as a digital
PSoC block or an analog PSoC block.
buffer
1. A storage area for data that is used to compensate for a speed difference, when transferring
data from one device to another. Usually refers to an area reserved for IO operations, into
which data is read, or from which data is written.
2. A portion of memory set aside to store data, often before it is sent to an external device or as
it is received from an external device.
3. An amplifier used to lower the output impedance of a system.
bus
1. A named connection of nets. Bundling nets together in a bus makes it easier to route nets
with similar routing patterns.
2. A set of signals performing a common function and carrying similar data. Typically represented
using vector notation; for example, address[7:0].
3. One or more conductors that serve as a common connection for a group of related devices.
clock
The device that generates a periodic signal with a fixed frequency and duty cycle. A clock is
sometimes used to synchronize different logic blocks.
comparator
An electronic circuit that produces an output voltage or current whenever two input levels simultaneously
satisfy predetermined amplitude requirements.
compiler
A program that translates a high level language, such as C, into machine language.
configuration
space
In PSoC devices, the register space accessed when the XIO bit, in the CPU_F register, is set to
‘1’.
crystal oscillator
An oscillator in which the frequency is controlled by a piezoelectric crystal. Typically a piezoelectric
crystal is less sensitive to ambient temperature than other circuit components.
cyclic redundancy A calculation used to detect errors in data communications, typically performed using a linear
check (CRC)
feedback shift register. Similar calculations may be used for a variety of other purposes such as
data compression.
data bus
A bi-directional set of signals used by a computer to convey information from a memory location
to the central processing unit and vice versa. More generally, a set of signals used to convey
data between digital functions.
debugger
A hardware and software system that allows you to analyze the operation of the system
under development. A debugger usually allows the developer to step through the firmware one
step at a time, set break points, and analyze memory.
dead band
A period of time when neither of two or more signals are in their active state or in transition.
digital blocks
The 8-bit logic blocks that can act as a counter, timer, serial receiver, serial transmitter, CRC
generator, pseudo-random number generator, or SPI.
Document Number: 38-12013 Rev. *S
Page 55 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Glossary (continued)
digital-to-analog
(DAC)
A device that changes a digital signal to an analog signal of corresponding magnitude. The analogto-digital (ADC) converter performs the reverse operation.
duty cycle
The relationship of a clock period high time to its low time, expressed as a percent.
emulator
Duplicates (provides an emulation of) the functions of one system with a different system, so that
the second system appears to behave like the first system.
External Reset
(XRES)
An active high signal that is driven into the PSoC device. It causes all operation of the CPU and
blocks to stop and return to a pre-defined state.
Flash
An electrically programmable and erasable, non-volatile technology that provides you the
programmability and data storage of EPROMs, plus in-system erasability. Non-volatile means
that the data is retained when power is OFF.
Flash block
The smallest amount of Flash ROM space that may be programmed at one time and the smallest
amount of Flash space that may be protected. A Flash block holds 64 bytes.
frequency
The number of cycles or events per unit of time, for a periodic function.
gain
The ratio of output current, voltage, or power to input current, voltage, or power, respectively.
Gain is usually expressed in dB.
I2C
A two-wire serial computer bus by Philips Semiconductors (now NXP Semiconductors). I2C is an
Inter-Integrated Circuit. It is used to connect low-speed peripherals in an embedded system. The
original system was created in the early 1980s as a battery control interface, but it was later used
as a simple internal bus system for building control electronics. I2C uses only two bi-directional
pins, clock and data, both running at +5V and pulled high with resistors. The bus operates at 100
kbits/second in standard mode and 400 kbits/second in fast mode.
ICE
The in-circuit emulator that allows you to test the project in a hardware environment, while
viewing the debugging device activity in a software environment (PSoC Designer).
input/output (I/O) A device that introduces data into or extracts data from a system.
interrupt
A suspension of a process, such as the execution of a computer program, caused by an event
external to that process, and performed in such a way that the process can be resumed.
interrupt service
routine (ISR)
A block of code that normal code execution is diverted to when the M8C receives a hardware
interrupt. Many interrupt sources may each exist with its own priority and individual ISR code
block. Each ISR code block ends with the RETI instruction, returning the device to the point in
the program where it left normal program execution.
jitter
1. A misplacement of the timing of a transition from its ideal position. A typical form of corruption that occurs on
serial data streams.
2. The abrupt and unwanted variations of one or more signal characteristics, such as the interval between
successive pulses, the amplitude of successive cycles, or the frequency or phase of successive cycles.
low-voltage detect A circuit that senses VDD and provides an interrupt to the system when VDD falls lower than a selected threshold.
(LVD)
M8C
An 8-bit Harvard-architecture microprocessor. The microprocessor coordinates all activity inside
a PSoC by interfacing to the Flash, SRAM, and register space.
Document Number: 38-12013 Rev. *S
Page 56 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Glossary (continued)
master device
A device that controls the timing for data exchanges between two devices. Or when devices are
cascaded in width, the master device is the one that controls the timing for data exchanges
between the cascaded devices and an external interface. The controlled device is called the
slave device.
microcontroller
An integrated circuit chip that is designed primarily for control systems and products. In addition
to a CPU, a microcontroller typically includes memory, timing circuits, and IO circuitry. The reason
for this is to permit the realization of a controller with a minimal quantity of chips, thus
achieving maximal possible miniaturization. This in turn, reduces the volume and the cost of
the controller. The microcontroller is normally not used for general-purpose computation as is a
microprocessor.
mixed-signal
The reference to a circuit containing both analog and digital techniques and components.
modulator
A device that imposes a signal on a carrier.
noise
1. A disturbance that affects a signal and that may distort the information carried by the signal.
2. The random variations of one or more characteristics of any entity such as voltage, current, or data.
oscillator
A circuit that may be crystal controlled and is used to generate a clock frequency.
parity
A technique for testing transmitting data. Typically, a binary digit is added to the data to make the
sum of all the digits of the binary data either always even (even parity) or always odd (odd parity).
Phase-locked
loop (PLL)
An electronic circuit that controls an oscillator so that it maintains a constant phase angle relative
to a reference signal.
pinouts
The pin number assignment: the relation between the logical inputs and outputs of the PSoC
device and their physical counterparts in the printed circuit board (PCB) package. Pinouts
involve pin numbers as a link between schematic and PCB design (both being computer generated
files) and may also involve pin names.
port
A group of pins, usually eight.
Power on reset
(POR)
A circuit that forces the PSoC device to reset when the voltage is lower than a pre-set level. This is a type of
hardware reset.
PSoC®
Cypress Semiconductor’s PSoC® is a registered trademark and Programmable System-onChip™ is a trademark of Cypress.
PSoC Designer™ The software for Cypress’ Programmable System-on-Chip technology.
pulse width
An output in the form of duty cycle which varies as a function of the applied measurand
modulator (PWM)
RAM
An acronym for random access memory. A data-storage device from which data can be read out
and new data can be written in.
register
A storage device with a specific capacity, such as a bit or byte.
reset
A means of bringing a system back to a know state. See hardware reset and software reset.
ROM
An acronym for read only memory. A data-storage device from which data can be read out, but
new data cannot be written in.
Document Number: 38-12013 Rev. *S
Page 57 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Glossary (continued)
serial
1. Pertaining to a process in which all events occur one after the other.
2. Pertaining to the sequential or consecutive occurrence of two or more related activities in a single device or
channel.
settling time
The time it takes for an output signal or value to stabilize after the input has changed from one
value to another.
shift register
A memory storage device that sequentially shifts a word either left or right to output a stream of
serial data.
slave device
A device that allows another device to control the timing for data exchanges between two
devices. Or when devices are cascaded in width, the slave device is the one that allows another
device to control the timing of data exchanges between the cascaded devices and an external
interface. The controlling device is called the master device.
SRAM
An acronym for static random access memory. A memory device where you can store and
retrieve data at a high rate of speed. The term static is used because, after a value is loaded into an SRAM cell,
it remains unchanged until it is explicitly altered or until power is removed from the device.
SROM
An acronym for supervisory read only memory. The SROM holds code that is used to boot the
device, calibrate circuitry, and perform Flash operations. The functions of the SROM may be
accessed in normal user code, operating from Flash.
stop bit
A signal following a character or block that prepares the receiving device to receive the next
character or block.
synchronous
1. A signal whose data is not acknowledged or acted upon until the next active edge of a clock signal.
2. A system whose operation is synchronized by a clock signal.
tri-state
A function whose output can adopt three states: 0, 1, and Z (high-impedance). The function does
not drive any value in the Z state and, in many respects, may be considered to be disconnected
from the rest of the circuit, allowing another output to drive the same net.
UART
A UART or universal asynchronous receiver-transmitter translates between parallel bits of data
and serial bits.
user modules
Pre-build, pre-tested hardware/firmware peripheral functions that take care of managing and
configuring the lower level Analog and Digital PSoC Blocks. User Modules also provide high
level API (Application Programming Interface) for the peripheral function.
user space
The bank 0 space of the register map. The registers in this bank are more likely to be modified
during normal program execution and not just during initialization. Registers in bank 1 are most
likely to be modified only during the initialization phase of the program.
VDD
A name for a power net meaning "voltage drain." The most positive power supply signal. Usually
5 V or 3.3 V.
VSS
A name for a power net meaning "voltage source." The most negative power supply signal.
watchdog timer
A timer that must be serviced periodically. If it is not serviced, the CPU resets after a specified
period of time.
Document Number: 38-12013 Rev. *S
Page 58 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Document History Page
Document Title: CY8C29466, CY8C29566, CY8C29666, CY8C29866 PSoC® Programmable System-on-Chip™
Document Number: 38-12013
Revision
ECN
Origin of
Change
Submission Date
Description of Change
**
131151
New Silicon
11/13/2003
New document (Revision **).
*A
132848
NWJ
01/21/2004
New information. First edition of preliminary datasheet.
*B
133205
NWJ
01/27/2004
Changed part numbers, increased SRAM data storage to 2 K bytes.
*C
133656
SFV
02/09/2004
Changed part numbers and removed a 28-pin SOIC.
*D
227240
SFV
06/01/2004
Changes to Overview section, 48-pin MLF pinout, and significant changes
to the Electrical Specs.
*E
240108
SFV
See ECN
Added a 28-lead (300 mil) SOIC part.
*F
247492
SFV
See ECN
New information added to the Electrical Specifications chapter.
*G
288849
HMT
See ECN
Add DS standards, update device table, fine-tune pinouts, add Reflow Peak
Temp. table. Finalize.
*H
722736
HMT
See ECN
Add QFN package clarifications. Add new QFN diagram. Add Low Power
Comparator (LPC) AC/DC electrical spec. tables. Add CY8C20x34 to PSoC
Device Characteristics table. Update emulation pod/feet kit part numbers.
Add OCD non-production pinouts and package diagrams. Add ISSP note to
pinout tables. Update package diagram revisions. Update typical and
recommended Storage Temperature per industrial specs. Update CY
branding and QFN convention. Add new Dev. Tool section. Update copyright
and trademarks.
*I
2503350
DFK/PYRS
See ECN
Pinout for CY8C29000 OCD wrongly included details of CY8C24X94. The
correct pinout for CY8C29000 is included in this version. Added note on
digital signaling in “DC Analog Reference Specifications” section.
*J
2545030
YARA
07/29/08
Added note to Ordering Information
*K
2708295
JVY
04/22/2009
Changed title from “CY8C29466, CY8C29566, CY8C29666, and
CY8C29866 PSoC Mixed Signal Array Final datasheet” to “CY8C29466,
CY8C29566, CY8C29666, and CY8C29866 PSoC® Programmable
System-on-Chip™”
Updated to datasheet template
Added 48-Pin QFN (Sawn) package diagram and CY8C29666-24LTXI and
CY8C29666-24LTXIT part details in the Ordering Information table
Updated DC GPIO, AC Chip-Level, and AC Programming Specifications as
follows:
Modified FIMO6 (page 27), TWRITE specifications (page 34)
Added IOH (page 21), IOL (page 21), DCILO (page 28), F32K_U (page 27),
TPOWERUP (page 28), TERASEALL (page 34), TPROGRAM_HOT (page 34), and
TPROGRAM_COLD (page 34) specifications
*L
2761941
DRSW/AESA
09/10/2009
Added SRPOWER_UP parameter in AC specs table..
*M
2842762
DRSW
01/08/2010
Corrected Notes for VDD parameter in Table 13, “DC Chip-Level Specifications,” on page 20.
Added “Contents” on page 2.
Updated links in Sales, Solutions, and Legal Information.
Document Number: 38-12013 Rev. *S
Page 59 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Document Title: CY8C29466, CY8C29566, CY8C29666, CY8C29866 PSoC® Programmable System-on-Chip™
Document Number: 38-12013
Revision
ECN
Origin of
Change
Submission Date
*N
2902396
NJF
03/30/2010
Updated Digital System Block Diagram and content in Digital System
Updated Cypress website links.
Removed reference to PSoC Designer 4.4 in PSoC Designer Software
Subsystems
Added TBAKETEMP and TBAKETIME parameters in Absolute Maximum
Ratings
Updated AC Chip-Level Specifications
Changed unit for SPIS function to ns in AC Digital Block Specifications
Updated notes in Packaging Information and package diagrams.
Updated Solder Reflow Specifications
Updated Emulation and Programming Accessories
Removed Third Party Tools and Build a PSoC Emulator into Your Board.
Updated Ordering Information and Ordering Code Definitions.
*O
2940410
YJI
05/31/2010
Updated content to match current style guide and datasheet template.
No technical updates.
*P
3044869
NJF
10/01/2010
Added PSoC Device Characteristics table .
Added DC I2C Specifications table.
Added F32K_U max limit.
Added Tjit_IMO specification, removed existing jitter specifications.
Updated Analog reference tables.
Updated Units of Measure, Acronyms, Glossary, and References sections.
Updated solder reflow specifications.
No specific changes were made to AC Digital Block Specifications table and
I2C Timing Diagram. They were updated for clearer understanding.
Updated Figure 13 since the labelling for y-axis was incorrect.
Template and styles update.
Removed footnote reference for “Solder Reflow Peak Temperature” table.
*Q
3017427
GDK
11/08/10
Removed the pruned part “CY8C29666-24LFXI” from the
Ordering Information and Accessories (Emulation and Programming).
*R
3263978
NJF
05/23/11
Updated Logic Block Diagram.
Updated Solder Reflow Specifications.
*S
3301676
NJF
07/04/11
Fixed page numbering error on footer.
Document Number: 38-12013 Rev. *S
Description of Change
Page 60 of 61
[+] Feedback
CY8C29466, CY8C29566
CY8C29666, CY8C29866
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
psoc.cypress.com/solutions
cypress.com/go/clocks
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/interface
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
Touch Sensing
cypress.com/go/psoc
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2003-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 38-12013 Rev. *S
Revised July 7, 2011
Page 61 of 61
PSoC Designer™ and Programmable System-on-Chip™ are trademarks and PSoC® and CapSense® are registered trademarks of Cypress Semiconductor Corporation. Purchase of I2C components
from Cypress or one of its sublicensed Associated Companies conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to
the I2C Standard Specification as defined by Philips. As from October 1st, 2006 Philips Semiconductors has a new trade name - NXP Semiconductors. All products and company names mentioned in
this document may be the trademarks of their respective holders.
[+] Feedback