CYPRESS CY8C24894_11

CY8C24894
®
Automotive PSoC
Programmable System-on-Chip™
Features
❐
Automotive Electronics Council (AEC) qualified
■
Powerful Harvard-architecture processor
❐ M8C processor speeds up to 24 MHz
❐ Two 8 × 8 multiply, 32-bit accumulate
❐ Low power at high speed
❐ Operating voltage: 3.0 V to 5.25 V
❐ Automotive temperature range: –40 °C to +85 °C
■
Advanced peripherals (PSoC® blocks)
❐ Six rail-to-rail analog PSoC blocks provide:
• Up to 14-bit analog-to-digital converters (ADCs)
• Up to 9-bit digital-to-analog converters (DACs)
• Programmable gain amplifiers (PGAs)
• Programmable filters and comparators
❐ Four digital PSoC blocks provide:
• 8- to 32-bit timers, counters, and pulse-width modulators
(PWMs)
• Cyclic redundancy check (CRC) and pseudo-random
sequence (PRS) modules
• Full- or half-duplex UART
• SPI master or slave
• Connectable to all general purpose I/O (GPIO) pins
❐ Complex peripherals by combining blocks
• Capacitive sensing application capability
■
■
■
Flexible on-chip memory
❐ 16 KB flash program storage, 1000 erase/write cycles
❐ 1 KB SRAM data storage
❐ In-system serial programming (ISSP)
❐ Partial flash updates
❐ Flexible protection modes
❐ EEPROM emulation in flash
■
Programmable pin configurations
❐ 25 mA sink, 10 mA drive on all GPIOs
❐ Pull-up, pull-down, high Z, strong, or open-drain drive modes
on all GPIOs
❐ Up to 47 analog inputs on GPIOs
❐ Two 30 mA analog outputs on GPIOs
❐ Configurable interrupt on all GPIOs
■
Precision, programmable clocking
❐ Internal ±4% 24/48 MHz oscillator
Cypress Semiconductor Corporation
Document Number: 001-53754 Rev. *D
Complete development tools
❐ Free development software (PSoC Designer™)
❐ Full-featured in-circuit emulator (ICE) and programmer
❐ Full-speed emulation
❐ Complex breakpoint structure
❐ 128 KB trace memory
Logic Block Diagram
Port 5
Port 7
System Bus
■
Internal low-speed, low-power oscillator for watchdog and
sleep functionality
❐ Optional external oscillator, up to 24 MHz
Additional system resources
2
❐ I C™ slave, master, or multimaster operation up to 400 kHz
❐ Watchdog and sleep timers
❐ User-configurable LVD
❐ Integrated supervisory circuit
❐ On-chip precision voltage reference
Port4
Global Digital Interconnect
Port 3
Port 2
Port 0 Analog
Drivers
Port 1
Global Analog Interconnect
PSoC CORE
SRAM
1K
SROM
Flash16K
CPU Core (M8C)
Interrupt
Controller
Sleep and
Watchdog
Clock Sources
(Includes IMO and ILO)
DIGITAL SYSTEM
ANALOG SYSTEM
Analog
Ref.
Digital
Block
Array
Analog
Block
Array
Digital
2
Decimator
Clocks MACs
Type2
I2C
POR and LVD
System Resets
Internal
Voltage
Ref.
Analog
Input
Muxing
SYSTEM RESOURCES
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised June 2, 2011
[+] Feedback
CY8C24894
Contents
PSoC Functional Overview .............................................. 3
The PSoC Core ........................................................... 3
The Digital System ...................................................... 3
The Analog System ..................................................... 4
Additional System Resources ..................................... 5
PSoC Device Characteristics ...................................... 5
Getting Started .................................................................. 6
Application Notes ........................................................ 6
Development Kits ........................................................ 6
Training ....................................................................... 6
CYPros Consultants .................................................... 6
Solutions Library .......................................................... 6
Technical Support ....................................................... 6
Development Tools .......................................................... 6
PSoC Designer Software Subsystems ........................ 6
Designing with PSoC Designer ....................................... 7
Select User Modules ................................................... 7
Configure User Modules .............................................. 7
Organize and Connect ................................................ 7
Generate, Verify, and Debug ....................................... 7
Pinouts .............................................................................. 8
56-Pin Part Pinout (with XRES pin) ............................ 8
Registers ........................................................................... 9
Register Conventions .................................................. 9
Register Mapping Tables ............................................ 9
Register Map Bank 0 Table: User Space ................. 10
Register Map Bank 1 Table: Configuration Space ... 11
Document Number: 001-53754 Rev. *D
Electrical Specifications ................................................ 12
Absolute Maximum Ratings ....................................... 13
Operating Temperature ............................................. 13
DC Electrical Characteristics ..................................... 14
AC Electrical Characteristics ..................................... 26
Packaging Information ................................................... 34
Thermal Impedances ................................................. 34
Solder Reflow Specifications ..................................... 34
Tape and Reel Information ........................................ 35
Development Tool Selection ......................................... 36
Software .................................................................... 36
Development Kits ...................................................... 36
Evaluation Tools ........................................................ 36
Device Programmers ................................................. 37
Accessories (Emulation and Programming) .............. 37
Ordering Information ...................................................... 38
Ordering Code Definitions ......................................... 38
Reference Information ................................................... 39
Acronyms .................................................................. 39
Reference Documents ............................................... 39
Document Conventions ............................................. 40
Glossary .................................................................... 40
Document History Page ................................................. 45
Sales, Solutions, and Legal Information ...................... 46
Worldwide Sales and Design Support ....................... 46
Products .................................................................... 46
PSoC Solutions ......................................................... 46
Page 2 of 46
[+] Feedback
CY8C24894
The PSoC family consists of many Programmable
System-on-Chip with on-chip controller devices. All PSoC family
devices are designed to replace traditional microcontroller units
(MCUs), system ICs, and the numerous discrete components
that surround them. Configurable analog, digital, and interconnect circuitry enable a high level of integration in a host of
industrial, consumer, and communication applications.
The Digital System
The digital system is composed of four digital PSoC blocks. Each
block is an 8-bit resource used alone or combined with other
blocks to form 8-, 16-, 24-, and 32-bit peripherals, which are
called user modules.
Figure 1. Digital System Block Diagram
Port 7
Port 1
Port 2
To System Bus
Digital Clocks
From Core
Port 0
To Analog
System
DIGITAL SYSTEM
Digital PSoC Block Array
8
8
The PSoC Core
Row 0
DBB00
DBB01
DCB02
4
DCB03
4
GIE[7:0]
The PSoC Core is a powerful engine that supports a rich feature
set. The core includes a CPU, memory, clocks, and configurable
GPIOs.
The M8C CPU core is a powerful processor with speeds up to
24 MHz, providing a four-MIPS 8-bit Harvard architecture microprocessor. The CPU uses an interrupt controller with up to 20
vectors, to simplify programming of real-time embedded events.
Program execution is timed and protected using the included
sleep timer and watchdog timer (WDT).
Port 3
GIO[7:0]
Global Digital
Interconnect
Row Output
Configuration
The PSoC architecture, as illustrated in the Logic Block Diagram
on page 1, is comprised of four main areas: PSoc Core, digital
system, analog system, and system resources. Configurable
global busing allows all the device resources to be combined into
a complete custom system. The PSoC CY8C24x94 devices can
have up to seven I/O ports that connect to the global digital and
analog interconnects, providing access to four digital blocks and
six analog blocks.
Port 5
Port 4
This architecture allows the user to create customized peripheral
configurations that match the requirements of each individual
application. Additionally, a fast CPU, Flash program memory,
SRAM data memory, and configurable I/O are included in a
range of convenient pinouts and packages.
Row Input
Configuration
PSoC Functional Overview
8
8
GOE[7:0]
GOO[7:0]
Digital peripheral configurations include those listed below.
■
PWMs (8- to 32-bit)
■
PWMs with Dead band (8- to 24-bit)
■
Counters (8- to 32-bit)
■
Timers (8- to 32-bit)
■
Full- or half-duplex 8-bit UART with selectable parity
The PSoC device incorporates flexible internal clock generators,
including a 24-MHz internal main oscillator (IMO) accurate to
±4% over temperature and voltage. The 24-MHz IMO can also
be doubled to 48 MHz for use by the digital system. A low power
32-kHz internal low-speed oscillator (ILO) is provided for the
sleep timer and WDT. The clocks, together with programmable
clock dividers (as system resources), provide the flexibility to
integrate almost any timing requirement into the PSoC device.
■
SPI master and slave
■
I2C master, slave, or multimaster (implemented in a dedicated
I2C block)
■
Cyclic redundancy checker/generator (16-bit)
■
Infrared Data Association (IrDA)
■
PRS generators (8- to 32-bit)
PSoC GPIOs provide connection to the CPU, digital resources,
and analog resources of the device. Each pin’s drive mode may
be selected from eight options, allowing great flexibility in
external interfacing. Every pin is also capable of generating a
system interrupt.
The digital blocks can be connected to any GPIO through a
series of global buses that can route any signal to any pin. The
buses also allow signal multiplexing and performing logic operations. This configurability frees your designs from the constraints
of a fixed peripheral controller.
Memory encompasses 16 KB of flash for program storage, 1 KB
of SRAM for data storage, and up to 2 KB of emulated EEPROM
using the flash. Program flash has four protection levels on
blocks of 64 bytes, allowing customized software IP protection.
Digital blocks are provided in rows of four, where the number of
blocks varies by PSoC device family. This allows you the
optimum choice of system resources for your application. Family
resources are shown in Table 1 on page 5.
Document Number: 001-53754 Rev. *D
Page 3 of 46
[+] Feedback
CY8C24894
Figure 2. Analog System Block Diagram
The analog system is composed of six configurable blocks, each
comprised of an opamp circuit allowing the creation of complex
analog signal flows. Analog peripherals are very flexible and can
be customized to support specific application requirements.
Some of the more common PSoC analog functions (most
available as user modules) are listed below.
■
Filters (Two- and Four-pole band pass, low pass, and notch)
■
Amplifiers (up to two, with selectable gain to 48x)
■
Instrumentation amplifiers (one with selectable gain to 93x)
■
Comparators (up to two, with 16 selectable thresholds)
■
DACs (up to two, with 6- to 9-bit resolution)
■
Multiplying DACs (up to two, with 6- to 9-bit resolution)
■
High current output drivers (two with 30 mA drive)
■
1.3-V reference (as a system resource)
■
DTMF Dialer
■
P 0 [6 ]
P 0 [5 ]
P 0 [4 ]
P 0 [3 ]
P 0 [2 ]
P 0 [1 ]
P 0 [0 ]
P 2 [3 ]
AGNDIn RefIn
ADCs (up to two, with 6- to 14-bit resolution, selectable as
incremental, delta-sigma, or successive approximation register
(SAR))
P 0 [7 ]
Analog
■
A ll IO
(E x c e p t P o r t 7 )
Mux Bus
The Analog System
P 2 [1 ]
P 2 [6 ]
P 2 [4 ]
P 2 [2 ]
P 2 [0 ]
A C I 0 [1 :0 ]
A C I 1 [1 :0 ]
A r r a y In p u t
C o n f ig u r a t io n
B lo c k
A rray
AC B00
A C B 01
Modulators
A SC 10
A SD 11
■
Correlators
ASD20
A SC 21
■
Peak Detectors
■
Many other topologies possible
A n a lo g R e f e r e n c e
Analog blocks are arranged in a column of three, which includes
one continuous time (CT) and two switched capacitor (SC)
blocks, as shown in Figure 2.
In t e r f a c e t o
D ig it a l S y s t e m
R e fH i
R e fL o
AGND
R e fe r e n c e
G e n e ra to rs
A G N D In
R e fIn
B andgap
M 8 C In t e r f a c e ( A d d r e s s B u s , D a t a B u s , E t c .)
The Analog Multiplexer System
The analog mux bus can connect to every GPIO pin in ports 0-5.
Pins are connected to the bus individually or in any combination.
The bus also connects to the analog system for analysis with
comparators and ADCs. It can be split into two sections for simultaneous dual-channel processing. An additional 8:1 analog input
multiplexer provides a second path to bring Port 0 pins to the
analog array.
Switch control logic enables selected pins to precharge continuously under hardware control. This enables capacitive
measurement for applications such as touch sensing. Other
multiplexer applications include:
Document Number: 001-53754 Rev. *D
■
Track pad, finger sensing.
■
Chip-wide mux that allows analog input from up to 47 I/O pins.
■
Crosspoint connection between any I/O pin combination.
Page 4 of 46
[+] Feedback
CY8C24894
Additional System Resources
■
The decimator provides a custom hardware filter for digital
signal processing applications including creation of DeltaSigma ADCs.
■
Digital clock dividers provide three customizable clock
frequencies for use in applications. The clocks can be routed
to both the digital and analog systems. Additional clocks are
generated using digital PSoC blocks as clock dividers.
The I2C module provides 0 to 400 kHz communication over two
wires. Slave, master, and multi-master modes are all
supported.
■
Two multiply accumulates (MACs) provide fast 8-bit multipliers
with 32-bit accumulate, to assist in both general math and
digital filters.
LVD interrupts can signal the application of falling voltage
levels, while the advanced POR circuit eliminates the need for
a system supervisor.
■
An internal 1.3-V voltage reference provides an absolute
reference for the analog system, including ADCs and DACs.
■
Versatile analog multiplexer system.
System resources provide additional capability useful for
complete systems. Additional resources include a multiplier,
decimator, LVD, and power-on reset (POR). Brief statements
describing the merits of each resource follow.
■
■
PSoC Device Characteristics
Depending on your PSoC device characteristics, the digital and analog systems can have varying numbers of digital and analog
blocks. The following table lists the resources available for specific PSoC device groups. The device covered by this datasheet is
shown in the highlighted row of the table.
Table 1. PSoC Device Characteristics
PSoC Part
Number
Digital
I/O
CY8C29x66[1]
up to 64
CY8C28xxx
up to 44
Digital
Rows
Digital
Blocks
Analog
Inputs
Analog
Outputs
4
16
up to 12
4
up to 3
up to 12
up to 44
up to 4
Analog
Columns
Analog
Blocks
SRAM
Size
Flash
Size
4
12
2K
32 K
up to 6
up to
12 + 4[2]
1K
16 K
CY8C27x43
up to 44
2
8
up to 12
4
4
12
256
16 K
CY8C24x94[1]
up to 56
1
4
up to 48
2
2
6
1K
16 K
CY8C24x23A[1]
up to 24
1
4
up to 12
2
2
6
256
4K
CY8C23x33
up to 26
1
4
up to 12
2
2
4
256
8K
CY8C22x45[1]
up to 38
2
8
up to 38
0
4
6[2]
1K
16 K
CY8C21x45[1]
up to 24
1
4
up to 24
0
4
6[2]
512
8K
CY8C21x34[1]
up to 28
1
4
up to 28
0
2
4[2]
512
8K
CY8C21x23
up to 16
1
4
up to 8
0
2
4[2]
256
4K
[2,3]
CY8C20x34
[1]
CY8C20xx6
up to 28
0
0
up to 28
0
0
3
up to 36
0
0
up to 36
0
0
3[2,3]
512
8K
up to 2 K
up to 32 K
Notes
1. Automotive qualified devices available in this group.
2. Limited analog functionality.
3. Two analog blocks and one CapSense® block.
Document Number: 001-53754 Rev. *D
Page 5 of 46
[+] Feedback
CY8C24894
Getting Started
For in depth information, along with detailed programming
details, see the PSoC® Technical Reference Manual.
For up-to-date ordering, packaging, and electrical specification
information, see the latest PSoC device datasheets on the web.
Application Notes
Cypress application notes are an excellent introduction to the
wide variety of possible PSoC designs.
Development Kits
PSoC Development Kits are available online from and through a
growing number of regional and global distributors, which
include Arrow, Avnet, Digi-Key, Farnell, Future Electronics, and
Newark.
Training
Free PSoC technical training (on demand, webinars, and
workshops), which is available online via www.cypress.com,
covers a wide variety of topics and skill levels to assist you in
your designs.
CYPros Consultants
Certified PSoC consultants offer everything from technical assistance to completed PSoC designs. To contact or become a PSoC
consultant go to the CYPros Consultants web site.
Solutions Library
Visit our growing library of solution focused designs. Here you
can find various application designs that include firmware and
hardware design files that enable you to complete your designs
quickly.
■
Free C compiler with no size restrictions or time limits
■
Built-in debugger
■
In-circuit emulation
■
Built-in support for communication interfaces:
2
❐ Hardware and software I C slaves and masters
❐ Full-speed USB 2.0
❐ Up to four full-duplex universal asynchronous receiver/transmitters (UARTs), SPI master and slave, and wireless
PSoC Designer supports the entire library of PSoC 1 devices and
runs on Windows XP, Windows Vista, and Windows 7.
PSoC Designer Software Subsystems
Design Entry
In the chip-level view, choose a base device to work with. Then
select different onboard analog and digital components that use
the PSoC blocks, which are called user modules. Examples of
user modules are analog-to-digital converters (ADCs),
digital-to-analog converters (DACs), amplifiers, and filters.
Configure the user modules for your chosen application and
connect them to each other and to the proper pins. Then
generate your project. This prepopulates your project with APIs
and libraries that you can use to program your application.
The tool also supports easy development of multiple configurations and dynamic reconfiguration. Dynamic reconfiguration
makes it possible to change configurations at run time. In
essence, this allows you to use more than 100 percent of PSoC's
resources for a given application.
Code Generation Tools
Technical Support
The code generation tools work seamlessly within the
PSoC Designer interface and have been tested with a full range
of debugging tools. You can develop your design in C, assembly,
or a combination of the two.
Technical support – including a searchable Knowledge Base
articles and technical forums – is also available online. If you
cannot find an answer to your question, call our Technical
Support hotline at 1-800-541-4736.
Assemblers. The assemblers allow you to merge assembly
code seamlessly with C code. Link libraries automatically use
absolute addressing or are compiled in relative mode, and linked
with other software modules to get absolute addressing.
Development Tools
C Language Compilers. C language compilers are available
that support the PSoC family of devices. The products allow you
to create complete C programs for the PSoC family devices. The
optimizing C compilers provide all of the features of C, tailored
to the PSoC architecture. They come complete with embedded
libraries providing port and bus operations, standard keypad and
display support, and extended math functionality.
PSoC Designer™ is the revolutionary Integrated Design
Environment (IDE) that you can use to customize PSoC to meet
your specific application requirements. PSoC Designer software
accelerates system design and time to market. Develop your
applications using a library of precharacterized analog and digital
peripherals (called user modules) in a drag-and-drop design
environment. Then, customize your design by leveraging the
dynamically generated application programming interface (API)
libraries of code. Finally, debug and test your designs with the
integrated debug environment, including in-circuit emulation and
standard software debug features. PSoC Designer includes:
■
Application editor graphical user interface (GUI) for device and
user module configuration and dynamic reconfiguration
■
Extensive user module catalog
■
Integrated source-code editor (C and assembly)
Document Number: 001-53754 Rev. *D
Debugger
PSoC Designer has a debug environment that provides
hardware in-circuit emulation, allowing you to test the program in
a physical system while providing an internal view of the PSoC
device. Debugger commands allow you to read and program and
read and write data memory, and read and write I/O registers.
You can read and write CPU registers, set and clear breakpoints,
and provide program run, halt, and step control. The debugger
also allows you to create a trace buffer of registers and memory
locations of interest.
Page 6 of 46
[+] Feedback
CY8C24894
Online Help System
The online help system displays online, context-sensitive help.
Designed for procedural and quick reference, each functional
subsystem has its own context-sensitive help. This system also
provides tutorials and links to FAQs and an Online Support
Forum to aid the designer.
In-Circuit Emulator
A low-cost, high-functionality In-Circuit Emulator (ICE) is
available for development support. This hardware can program
single devices.
The emulator consists of a base unit that connects to the PC
using a USB port. The base unit is universal and operates with
all PSoC devices. Emulation pods for each device family are
available separately. The emulation pod takes the place of the
PSoC device in the target board and performs full-speed
(24-MHz) operation.
Designing with PSoC Designer
The development process for the PSoC® device differs from that
of a traditional fixed function microprocessor. The configurable
analog and digital hardware blocks give the PSoC architecture a
unique flexibility that pays dividends in managing specification
change during development and by lowering inventory costs.
These configurable resources, called PSoC Blocks, have the
ability to implement a wide variety of user-selectable functions.
The PSoC development process is summarized in four steps:
1. Select User Modules.
2. Configure user modules.
3. Organize and connect.
4. Generate, verify, and debug.
Select User Modules
PSoC Designer provides a library of prebuilt, pretested hardware
peripheral components called “user modules.” User modules
make selecting and implementing peripheral devices, both
analog and digital, simple.
Configure User Modules
Each user module that you select establishes the basic register
settings that implement the selected function. They also provide
parameters and properties that allow you to tailor their precise
Document Number: 001-53754 Rev. *D
configuration to your particular application. For example, a pulse
width modulator (PWM) User Module configures one or more
digital PSoC blocks, one for each 8 bits of resolution. The user
module parameters permit you to establish the pulse width and
duty cycle. Configure the parameters and properties to correspond to your chosen application. Enter values directly or by
selecting values from drop-down menus. All the user modules
are documented in datasheets that may be viewed directly in
PSoC Designer or on the Cypress website. These user module
datasheets explain the internal operation of the user module and
provide performance specifications. Each datasheet describes
the use of each user module parameter, and other information
you may need to successfully implement your design.
Organize and Connect
You build signal chains at the chip level by interconnecting user
modules to each other and the I/O pins. You perform the
selection, configuration, and routing so that you have complete
control over all on-chip resources.
Generate, Verify, and Debug
When you are ready to test the hardware configuration or move
on to developing code for the project, you perform the “Generate
Configuration Files” step. This causes PSoC Designer to
generate source code that automatically configures the device to
your specification and provides the software for the system. The
generated code provides application programming interfaces
(APIs) with high-level functions to control and respond to
hardware events at run time and interrupt service routines that
you can adapt as needed.
A complete code development environment allows you to
develop and customize your applications in either C, assembly
language, or both.
The last step in the development process takes place inside
PSoC Designer’s debugger (access by clicking the Connect
icon). PSoC Designer downloads the HEX image to the ICE
where it runs at full speed. PSoC Designer debugging capabilities rival those of systems costing many times more. In addition
to traditional single-step, run-to-breakpoint and watch-variable
features, the debug interface provides a large trace buffer and
allows you to define complex breakpoint events that include
monitoring address and data bus values, memory locations and
external signals.
Page 7 of 46
[+] Feedback
CY8C24894
Pinouts
The automotive CY8C24x94 PSoC device is available in a variety of packages which are listed and illustrated in the following tables.
Every port pin (labeled with a “P”) is capable of digital I/O. However, VSS, VDD, and XRES are not capable of digital I/O.
56-Pin Part Pinout (with XRES pin)
Table 2. 56-Pin Part Pinout (QFN)
Figure 3. CY8C24894 56-Pin PSoC Device
56
55
54
53
52
51
50
49
48
47
46
45
44
43
P2[5], M
P2[7], M
P0[1], M, AI
P0[3], M, AIO
P0[5], M, AIO
P0[7], M, AI
VSS
VDD
P0[6], M, AI
P0[4], M, AI
P0[2], M, AI
P0[0], M, AI
P2[6], M, Ext. VRef
P2[4], M, Ext. AGND
Type
Pin
Name
Description
No. Digital Analog
1
I/O
I, M
P2[3] Direct switched capacitor block input
2
I/O
I, M
P2[1] Direct switched capacitor block input
3
I/O
M
P4[7]
4
I/O
M
P4[5]
5
I/O
M
P4[3]
6
I/O
M
P4[1]
7
I/O
M
P3[7]
8
I/O
M
P3[5]
9
I/O
M
P3[3]
10
I/O
M
P3[1]
11
I/O
M
P5[7]
12
I/O
M
P5[5]
13
I/O
M
P5[3]
14
I/O
M
P5[1]
15
I/O
M
P1[7] I2C serial clock (SCL)
16
I/O
M
P1[5] I2C serial data (SDA)
17
I/O
M
P1[3]
18
I/O
M
P1[1] I2C SCL, ISSP SCLK[4]
19
Power
VSS Ground connection
20
DNC
Do not connect anything to this pin
21
DNC
Do not connect anything to this pin
22
Power
VDD Supply voltage
23
I/O
P7[7]
24
I/O
P7[0]
25
I/O
M
P1[0] I2C SDA, ISSP SDATA[4]
26
I/O
M
P1[2]
27
I/O
M
P1[4] Optional external clock (EXTCLK) input
28
I/O
M
P1[6]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
QFN
(Top View)
I/O
M
P5[0]
30
I/O
M
P5[2]
31
I/O
M
P5[4]
Type
Name
Pin
No. Digital Analog
32
I/O
M
P5[6]
45
I/O
I, M
P0[0]
33
I/O
M
P3[0]
46
I/O
I, M
P0[2]
Analog column mux input
34
I/O
M
P3[2]
47
I/O
I, M
P0[4]
Analog column mux input
35
I/O
M
P3[4]
48
I/O
I, M
P0[6]
Analog column mux input
49
VDD
Supply voltage
Input
P2[2], AI, M
P2[0], AI, M
P4[6], M
P4[4], M
P4[2], M
P4[0], M
XRES
P3[4], M
P3[2], M
P3[0], M
P5[6], M
P5[4], M
P5[2], M
P5[0], M
I2C SCL, M, P1[7]
I2C SDA, M, P1[5]
M, P1[3]
I2C SCL, M, P1[1]
VSS
DNC
DNC
VDD
P7[7]
P7[0]
I2C SDA, M, P1[0]
M, P1[2]
EXTCLK, M, P1[4]
M, P1[6]
29
36
42
41
40
39
38
37
36
35
34
33
32
31
30
29
15
16
17
18
19
20
21
22
23
24
25
26
27
28
AI, M, P2[3]
AI, M, P2[1]
M, P4[7]
M, P4[5]
M, P4[3]
M, P4[1]
M, P3[7]
M, P3[5]
M, P3[3]
M, P3[1]
M, P5[7]
M, P5[5]
M, P5[3]
M, P5[1]
Analog column mux input
37
I/O
M
XRES Active high external reset with internal
pull-down
P4[0]
38
I/O
M
P4[2]
51
I/O
I, M
P0[7]
Analog column mux input
39
I/O
M
P4[4]
52
I/O
I/O, M
P0[5]
Analog column mux input and column output
40
I/O
M
P4[6]
53
I/O
I/O, M
P0[3]
Analog column mux input and column output
41
I/O
I, M
P2[0]
Direct switched capacitor block input
54
I/O
I, M
P0[1]
Analog column mux input
42
I/O
I, M
P2[2]
Direct switched capacitor block input
55
I/O
M
P2[7]
43
I/O
M
P2[4]
External analog ground (AGND) input
56
I/O
M
P2[5]
44
I/O
M
P2[6]
External voltage reference (VREF) input
EP
50
Power
Description
Power
Power
VSS
VSS
Ground connection
Exposed pad is not connected internally. Connect
to circuit ground for best performance
LEGEND A = Analog, I = Input, O = Output, and M = Analog Mux Input.
Note
4. These are the ISSP pins, which are not high Z when coming out of reset state. See the PSoC Technical Reference Manual for details.
Document Number: 001-53754 Rev. *D
Page 8 of 46
[+] Feedback
CY8C24894
Registers
This section lists the registers of the automotive CY8C24x94 PSoC device family. For detailed register information, refer to the PSoC
Technical Reference Manual.
Register Conventions
Register Mapping Tables
The register conventions specific to this section are listed in the
following table.
The PSoC device has a total register address space of 512
bytes. The register space is referred to as I/O space and is
divided into two banks. The XIO bit in the Flag register (CPU_F)
determines which bank the user is currently in. When the XIO bit
is set the user is in Bank 1.
Convention
Description
R
Read register or bit(s)
W
Write register or bit(s)
L
Logical register or bit(s)
C
Clearable register or bit(s)
#
Access is bit specific
Document Number: 001-53754 Rev. *D
Note In the following register mapping tables, blank fields are
Reserved and should not be accessed.
Page 9 of 46
[+] Feedback
CY8C24894
Register Map Bank 0 Table: User Space
Name
Addr (0,Hex) Access
Name
PRT0DR
PRT0IE
PRT0GS
PRT0DM2
PRT1DR
PRT1IE
PRT1GS
PRT1DM2
PRT2DR
PRT2IE
PRT2GS
PRT2DM2
PRT3DR
PRT3IE
PRT3GS
PRT3DM2
PRT4DR
PRT4IE
PRT4GS
PRT4DM2
PRT5DR
PRT5IE
PRT5GS
PRT5DM2
00
RW
01
RW
02
RW
03
RW
04
RW
05
RW
06
RW
07
RW
08
RW
09
RW
0A
RW
0B
RW
0C
RW
0D
RW
0E
RW
0F
RW
10
RW
11
RW
12
RW
13
RW
14
RW
15
RW
16
RW
17
RW
18
19
1A
1B
PRT7DR
1C
RW
PRT7IE
1D
RW
PRT7GS
1E
RW
PRT7DM2
1F
RW
DBB00DR0
20
#
AMX_IN
DBB00DR1
21
W
AMUXCFG
DBB00DR2
22
RW
DBB00CR0
23
#
ARF_CR
DBB01DR0
24
#
CMP_CR0
DBB01DR1
25
W
ASY_CR
DBB01DR2
26
RW
CMP_CR1
DBB01CR0
27
#
DCB02DR0
28
#
DCB02DR1
29
W
DCB02DR2
2A
RW
DCB02CR0
2B
#
DCB03DR0
2C
#
TMP_DR0
DCB03DR1
2D
W
TMP_DR1
DCB03DR2
2E
RW
TMP_DR2
DCB03CR0
2F
#
TMP_DR3
30
ACB00CR3
31
ACB00CR0
32
ACB00CR1
33
ACB00CR2
34
ACB01CR3
35
ACB01CR0
36
ACB01CR1
37
ACB01CR2
38
39
3A
3B
3C
3D
3E
3F
Blank fields are Reserved and should not be accessed.
Document Number: 001-53754 Rev. *D
Addr (0,Hex) Access
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
RW
RW
RW
#
#
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Addr (0,Hex) Access
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
ASD20CR0
90
ASD20CR1
91
ASD20CR2
92
ASD20CR3
93
ASC21CR0
94
ASC21CR1
95
ASC21CR2
96
ASC21CR3
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
MUL1_X
A8
MUL1_Y
A9
MUL1_DH
AA
MUL1_DL
AB
ACC1_DR1
AC
ACC1_DR0
AD
ACC1_DR3
AE
ACC1_DR2
AF
RDI0RI
B0
RDI0SYN
B1
RDI0IS
B2
RDI0LT0
B3
RDI0LT1
B4
RDI0RO0
B5
RDI0RO1
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
# Access is bit specific.
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
W
W
R
R
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
CUR_PP
STK_PP
IDX_PP
MVR_PP
MVW_PP
I2C_CFG
I2C_SCR
I2C_DR
I2C_MSCR
INT_CLR0
INT_CLR1
INT_CLR2
INT_CLR3
INT_MSK3
INT_MSK2
INT_MSK0
INT_MSK1
INT_VC
RES_WDT
DEC_DH
DEC_DL
DEC_CR0
DEC_CR1
MUL0_X
MUL0_Y
MUL0_DH
MUL0_DL
ACC0_DR1
ACC0_DR0
ACC0_DR3
ACC0_DR2
CPU_F
DAC_D
CPU_SCR1
CPU_SCR0
Addr (0,Hex) Access
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
RW
RW
RW
RW
RW
RW
#
RW
#
RW
RW
RW
RW
RW
RW
RW
RW
RC
W
RC
RC
RW
RW
W
W
R
R
RW
RW
RW
RW
RL
RW
#
#
Page 10 of 46
[+] Feedback
CY8C24894
Register Map Bank 1 Table: Configuration Space
Name
Addr (1,Hex) Access
Name
PRT0DM0
PRT0DM1
PRT0IC0
PRT0IC1
PRT1DM0
PRT1DM1
PRT1IC0
PRT1IC1
PRT2DM0
PRT2DM1
PRT2IC0
PRT2IC1
PRT3DM0
PRT3DM1
PRT3IC0
PRT3IC1
PRT4DM0
PRT4DM1
PRT4IC0
PRT4IC1
PRT5DM0
PRT5DM1
PRT5IC0
PRT5IC1
00
RW
01
RW
02
RW
03
RW
04
RW
05
RW
06
RW
07
RW
08
RW
09
RW
0A
RW
0B
RW
0C
RW
0D
RW
0E
RW
0F
RW
10
RW
11
RW
12
RW
13
RW
14
RW
15
RW
16
RW
17
RW
18
19
1A
1B
PRT7DM0
1C
RW
PRT7DM1
1D
RW
PRT7IC0
1E
RW
PRT7IC1
1F
RW
DBB00FN
20
RW
CLK_CR0
DBB00IN
21
RW
CLK_CR1
DBB00OU
22
RW
ABF_CR0
23
AMD_CR0
DBB01FN
24
RW
CMP_GO_EN
DBB01IN
25
RW
DBB01OU
26
RW
AMD_CR1
27
ALT_CR0
DCB02FN
28
RW
DCB02IN
29
RW
DCB02OU
2A
RW
2B
DCB03FN
2C
RW
TMP_DR0
DCB03IN
2D
RW
TMP_DR1
DCB03OU
2E
RW
TMP_DR2
2F
TMP_DR3
30
ACB00CR3
31
ACB00CR0
32
ACB00CR1
33
ACB00CR2
34
ACB01CR3
35
ACB01CR0
36
ACB01CR1
37
ACB01CR2
38
39
3A
3B
3C
3D
3E
3F
Blank fields are Reserved and should not be accessed.
Document Number: 001-53754 Rev. *D
Addr (1,Hex) Access
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Name
ASC10CR0
ASC10CR1
ASC10CR2
ASC10CR3
ASD11CR0
ASD11CR1
ASD11CR2
ASD11CR3
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
Addr (1,Hex) Access
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
ASD20CR1
91
ASD20CR2
92
ASD20CR3
93
ASC21CR0
94
ASC21CR1
95
ASC21CR2
96
ASC21CR3
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
AF
RDI0RI
B0
RDI0SYN
B1
RDI0IS
B2
RDI0LT0
B3
RDI0LT1
B4
RDI0RO0
B5
RDI0RO1
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
# Access is bit specific.
Name
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
GDI_O_IN
GDI_E_IN
GDI_O_OU
GDI_E_OU
MUX_CR0
MUX_CR1
MUX_CR2
MUX_CR3
OSC_GO_EN
OSC_CR4
OSC_CR3
OSC_CR0
OSC_CR1
OSC_CR2
VLT_CR
VLT_CMP
IMO_TR
ILO_TR
BDG_TR
ECO_TR
MUX_CR4
MUX_CR5
RW
RW
RW
RW
RW
RW
RW
CPU_F
DAC_CR
CPU_SCR1
CPU_SCR0
Addr (1,Hex) Access
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
R
W
W
RW
W
RW
RW
RL
RW
#
#
Page 11 of 46
[+] Feedback
CY8C24894
Electrical Specifications
This section presents the DC and AC electrical specifications of the automotive CY8C24x94 PSoC device family. For the most up to
date electrical specifications, confirm that you have the most recent datasheet by visiting http://www.cypress.com.
Specifications are valid for –40 °C ≤ TA ≤ 85 °C and TJ ≤ 100 °C, except where noted.
Figure 4. Voltage versus CPU Frequency
5.25
lid ing
Va rat n
e io
Op eg
R
VDD Voltage (V)
4.75
3.0
0
93 kHz
12 MHz
24 MHz
CPU Frequency
(nominal setting)
Document Number: 001-53754 Rev. *D
Page 12 of 46
[+] Feedback
CY8C24894
Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. User guidelines are not tested.
Table 3. Absolute Maximum Ratings
Symbol
TSTG
Description
Storage temperature
TBAKETEMP Bake temperature
tBAKETIME
TA
VDD
VIO
VIO2
IMIO
IMAIO
ESD
LU
Min
–55
Typ
25
–
125
Bake time
See
package
label
Ambient temperature with power applied
–40
Supply voltage on VDD relative to VSS
–0.5
DC input voltage
VSS – 0.5
DC voltage applied to tri-state
VSS – 0.5
Maximum current into any port pin
–25
Maximum current into any port pin
–50
configured as analog driver
Electro static discharge voltage
2000
Latch-up current
–
Max
+100
Units
Notes
°C
Higher storage temperatures
reduce data retention time.
Recommended storage
temperature is +25 °C ± 25 °C.
Time spent in storage at a
temperature greater than 65 °C
counts toward the FlashDR
electrical specification in Table 16
on page 25.
°C
–
See
package
label
72
Hours
–
–
–
–
–
–
+85
+6.0
VDD + 0.5
VDD + 0.5
+50
+50
°C
V
V
V
mA
mA
–
–
–
200
V
mA
Typ
–
–
Max
+85
+100
Human Body Model ESD.
Operating Temperature
Table 4. Operating Temperature
Symbol
Description
TA
Ambient temperature
TJ
Junction temperature
Document Number: 001-53754 Rev. *D
Min
–40
–40
Units
Notes
°C
°C
The temperature rise from ambient
to junction is package specific. See
Table 28 on page 34. The user must
limit the power consumption to
comply with this requirement.
Page 13 of 46
[+] Feedback
CY8C24894
DC Electrical Characteristics
DC Chip Level Specifications
Table 5 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are for
design guidance only.
Table 5. DC Chip-Level Specifications
Symbol
Description
VDD
Supply voltage
Min
3.0
Typ
–
Max
5.25
Units
V
IDD5
Supply current, IMO = 24 MHz, VDD = 5 V
–
14
27
mA
IDD3
Supply current, IMO = 24 MHz, VDD = 3.3 V
–
8
14
mA
ISB
Sleep (mode) current with POR, LVD, sleep
timer, and WDT.[5]
–
3
6.5
μA
ISBH
Sleep (mode) current with POR, LVD, sleep
timer, and WDT at high temperature.[5]
–
4
25
μA
Notes
See DC POR and LVD specifications,
Table 15 on page 24.
Conditions are VDD = 5.0 V, TA = 25 °C,
CPU = 3 MHz, 48 MHz disabled, VC1 =
1.5 MHz, VC2 = 93.75 kHz, VC3 = 93.75
kHz, Analog power = off.
Conditions are VDD = 3.3 V, TA = 25 °C,
CPU = 3 MHz, 48 MHz disabled, VC1 =
1.5 MHz, VC2 = 93.75 kHz, VC3 = 0.367
kHz, Analog power = off.
Conditions are with ILO active, VDD =
3.3 V, –40 °C ≤ TA ≤ 55 °C, Analog
power = off.
Conditions are with ILO active, VDD =
3.3 V, 55 °C < TA ≤ 85 °C, Analog power
= off.
DC GPIO Specifications
The following table lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V
and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C
and are for design guidance only.
Table 6. DC GPIO Specifications
Symbol
Description
RPU
Pull-up resistor
RPD
Pull-down resistor
Min
4
4
Typ
5.6
5.6
Max
8
8
Units
kΩ
kΩ
VOH
High output level
VDD – 1.0
–
–
V
VOL
Low output level
–
–
0.75
V
IOH
High level source current
10
–
–
mA
IOL
Low level sink current
25
–
–
mA
VIL
VIH
VH
IIL
CIN
Input low level
Input high level
Input hysterisis
Input leakage (absolute value)
Capacitive load on pins as input
–
2.1
–
–
–
–
–
60
1
3.5
0.8
–
–
–
10
V
V
mV
nA
pF
COUT
Capacitive load on pins as output
–
3.5
10
pF
Notes
Also applies to the internal pull-down
resistor on the XRES pin
IOH = 10 mA, VDD = 4.75 V to 5.25 V (8
total loads, 4 on even port pins (for
example, P0[2], P1[4]), 4 on odd port
pins (for example, P0[3], P1[5])). 80 mA
maximum combined IOH budget.
IOL = 25 mA, VDD = 4.75 V to 5.25 V (8
total loads, 4 on even port pins (for
example, P0[2], P1[4]), 4 on odd port
pins (for example, P0[3], P1[5])). 200
mA maximum combined IOL budget.
VOH ≥ VDD – 1.0 V, see the limitations
of the total current in the note for VOH.
VOL ≤ 0.75 V, see the limitations of the
total current in the note for VOL.
VDD = 3.0 V to 5.25 V.
VDD = 3.0 V to 5.25 V.
Gross tested to 1 μA.
Package and pin dependent.
TA = 25 °C.
Package and pin dependent.
TA = 25 °C.
Note
5. Standby current includes all functions (POR, LVD, WDT, sleep timer) needed for reliable system operation. This should be compared with devices that have similar
functions enabled.
Document Number: 001-53754 Rev. *D
Page 14 of 46
[+] Feedback
CY8C24894
DC Operational Amplifier Specifications
Table 7 and Table 8 on page 16 list the guaranteed maximum and minimum specifications for the voltage and temperature ranges:
4.75 V to 5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V
and 3.3 V at 25 °C and are for design guidance only.
The Operational Amplifier is a component of both the Analog Continuous Time (CT) PSoC blocks and the Analog Switched Capacitor
(SC) PSoC blocks. The guaranteed specifications are measured in the Analog Continuous Time PSoC block.
Table 7. 5-V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input offset voltage (absolute value)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
TCVOSOA Average input offset voltage Drift
Input leakage current (Port 0 Analog Pins)
IEBOA
Input capacitance (Port 0 Analog Pins)
CINOA
VCMOA
Common Mode Voltage Range
All cases, except highest
Power = high, Opamp bias = high
GOLOA
Open loop gain
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
VOHIGHOA High output voltage swing (internal
signals)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
VOLOWOA Low output voltage swing (internal
signals)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
ISOA
Supply current (including associated
AGND buffer)
Power = low, Opamp bias = low
Power = low, Opamp bias = high
Power = medium, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = low
Power = high, Opamp bias = high
PSRROA Supply voltage rejection ratio
Document Number: 001-53754 Rev. *D
Min
Typ
Max
Units
–
–
–
–
–
–
1.6
1.3
1.2
10
8
7.5
mV
mV
mV
7.0
20
4.5
35.0
–
9.5
μV/°C
pA
pF
0.0
0.5
–
–
VDD
VDD – 0.5
V
V
60
60
80
–
–
–
–
–
–
dB
dB
dB
VDD – 0.2
VDD – 0.2
VDD – 0.5
–
–
–
–
–
–
V
V
V
–
–
–
–
–
–
0.2
0.2
0.5
V
V
V
–
–
–
–
–
–
65
400
500
800
1200
2400
4600
80
800
900
1000
1600
3200
6400
–
μA
μA
μA
μA
μA
μA
dB
Notes
Gross tested to 1 μA.
Package and pin dependent. TA =
25 °C.
The common-mode input voltage
range is measured through an
analog output buffer. The specification includes the limitations
imposed by the characteristics of
the analog output buffer.
Specification is applicable at high
power. For all other bias modes
(except high power, high Opamp
bias), minimum is 60 dB.
VSS ≤ VIN ≤ (VDD – 2.25 V) or (VDD
– 1.25 V) ≤ VIN ≤ VDD.
Page 15 of 46
[+] Feedback
CY8C24894
Table 8. 3.3-V DC Operational Amplifier Specifications
Symbol
VOSOA
Description
Input offset voltage (absolute value)
Power = low, Opamp bias = high
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
TCVOSOA Average input offset voltage drift
IEBOA
Input leakage current (Port 0 analog pins)
Input capacitance (Port 0 analog pins)
CINOA
Min
Typ
Max
–
–
–
–
–
–
1.65
1.32
–
7.0
20
4.5
10
8
–
35.0
–
9.5
VCMOA
Common mode voltage range
0.2
–
GOLOA
Open loop gain
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
60
60
80
–
–
–
VDD – 0.2
VDD – 0.2
VDD – 0.2
–
–
–
–
–
–
V
V
V
–
–
–
–
–
–
0.2
0.2
0.2
V
V
V
VOHIGHOA High output voltage swing (internal signals)
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
VOLOWOA Low output voltage swing (internal signals)
Power = low, Opamp bias = low
Power = medium, Opamp bias = low
Power = high, Opamp bias = low
Supply current
ISOA
(including associated AGND buffer)
Power = low, Opamp bias = low
Power = low, Opamp bias = high
Power = medium, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = low
Power = high, Opamp bias = high
PSRROA Supply voltage rejection ratio
–
–
–
–
–
–
65
400
500
800
1200
2400
–
80
Units
Notes
Power = high, Opamp bias =
high setting is not allowed for
3.3 V VDD operation
mV
mV
mV
µV/°C
pA
Gross tested to 1 µA.
pF
Package and pin dependent.
TA = 25 °C.
VDD – 0.2
V
The common-mode input
voltage range is measured
through an analog output
buffer. The specification
includes the limitations
imposed by the characteristics
of the analog output buffer.
Specification is applicable at
–
dB
low Opamp bias. For high
–
dB
Opamp bias mode (except high
–
dB
power, high Opamp bias),
minimum is 60 dB.
800
900
1000
1600
3200
–
–
µA
µA
µA
µA
µA
µA
dB
Power = high, Opamp bias =
high setting is not allowed for
3.3 V VDD operation
VSS ≤ VIN ≤ (VDD – 2.25) or
(VDD – 1.25 V) ≤ VIN ≤ VDD
DC Low Power Comparator Specifications
Table 9 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V at 25 °C and are for design
guidance only.
Table 9. DC Low Power Comparator Specifications
Symbol
VREFLPC
ISLPC
VOSLPC
Description
Low power comparator (LPC) reference
voltage range
LPC supply current
LPC voltage offset
Document Number: 001-53754 Rev. *D
Min
0.2
Typ
–
Max
VDD – 1.0
Units
V
–
–
10
2.5
55
55
μA
mV
Notes
Page 16 of 46
[+] Feedback
CY8C24894
DC Analog Output Buffer Specifications
Table 10 and Table 11 on page 18 list the guaranteed maximum and minimum specifications for the voltage and temperature ranges:
4.75 V to 5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V
and 3.3 V at 25 °C and are for design guidance only.
Table 10. 5-V DC Analog Output Buffer Specifications
Symbol
VOSOB
TCVOSOB
VCMOB
ROUTOB
PSRROB
Description
Min
Input offset voltage (absolute value)
–
Average input offset voltage drift
–
Common mode input voltage range
0.5
Output resistance
Power = low
–
Power = high
–
High output voltage swing
(load = 32 Ω to VDD/2)
Power = low
0.5 × VDD + 1.1
Power = high
0.5 × VDD + 1.1
Low output voltage swing
(load = 32 Ω to VDD/2)
–
Power = low
–
Power = high
Supply current including opamp
bias cell (no load)
–
Power = low
–
Power = high
Supply voltage rejection ratio
53
CL
Load capacitance
VOHIGHOB
VOLOWOB
ISOB
Document Number: 001-53754 Rev. *D
–
Typ
3
+6
–
Max
12
–
VDD – 1.0
Units
mV
µV/°C
V
0.6
0.6
–
–
Ω
Ω
–
–
–
–
V
V
–
–
0.5 × VDD – 1.3
0.5 × VDD – 1.3
V
V
1.1
2.6
64
5.1
8.8
–
mA
mA
dB
–
200
pF
Notes
(0.5 × VDD – 1.3) ≤ VOUT ≤
(VDD – 2.3).
This specification applies to
the external circuit that is being
driven by the analog output
buffer.
Page 17 of 46
[+] Feedback
CY8C24894
Table 11. 3.3-V DC Analog Output Buffer Specifications
Symbol
VOSOB
TCVOSOB
VCMOB
ROUTOB
PSRROB
Description
Min
Input offset voltage (absolute value)
–
Average input offset voltage drift
–
Common mode input voltage range
0.5
Output resistance
Power = low
–
Power = high
–
High output voltage swing
(load = 1 KΩ to VDD/2)
0.5 × VDD + 1.0
Power = low
0.5 × VDD + 1.0
Power = high
Low output voltage swing
(load = 1 KΩ to VDD/2)
Power = low
–
Power = high
–
Supply current including opamp
bias cell (no load)
Power = low
–
Power = high
–
Supply voltage rejection ratio
34
CL
Load capacitance
VOHIGHOB
VOLOWOB
ISOB
Document Number: 001-53754 Rev. *D
–
Typ
3
+6
–
Max
12
–
VDD – 1.0
Units
mV
µV/°C
V
1
1
–
–
Ω
Ω
–
–
–
–
V
V
–
–
0.5 × VDD – 1.0
0.5 × VDD – 1.0
V
V
0.8
2.0
64
2.0
4.3
–
mA
mA
dB
–
200
pF
Notes
(0.5 × VDD – 1.0) ≤ VOUT ≤ (0.5
× VDD + 0.9).
This specification applies to the
external circuit that is being
driven by the analog output
buffer.
Page 18 of 46
[+] Feedback
CY8C24894
DC Analog Reference Specifications
Table 12 and Table 13 on page 22 list the guaranteed maximum and minimum specifications for the voltage and temperature ranges:
4.75 V to 5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V
and 3.3 V at 25 °C. These are for design guidance only.
The guaranteed specifications are measured through the analog CT PSoC blocks. The power levels for AGND refer to the power of
the analog CT PSoC block. The power levels for RefHi and RefLo refer to the Analog Reference Control register. The limits stated for
AGND include the offset error of the AGND buffer local to the analog CT PSoC block. Reference control power is high.
Note Avoid using P2[4] for digital signaling when using an analog resource that depends on the analog reference. Some coupling of
the digital signal may appear on the AGND.
Table 12. 5-V DC Analog Reference Specifications
Reference
ARF_CR
[5:3]
0b000
Reference Power
Settings
RefPower = high
Opamp bias = high
Reference
Description
Min
Typ
Max
Units
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.229 VDD/2 + 1.290 VDD/2 + 1.346
VAGND
AGND
VDD/2
VDD/2 – 0.038
VDD/2 + 0.040
V
VREFLO
Ref Low
VDD/2 – Bandgap
V
VDD/2
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 – 1.356 VDD/2 – 1.295 VDD/2 – 1.218
VDD/2 + 1.220 VDD/2 + 1.292 VDD/2 + 1.348
VAGND
AGND
VDD/2
VDD/2 – 0.036
VDD/2 + 0.036
V
VREFLO
Ref Low
VDD/2 – Bandgap
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
VDD/2 + Bandgap
VDD/2 – 1.357 VDD/2 – 1.297 VDD/2 – 1.225
VDD/2 + 1.221 VDD/2 + 1.293 VDD/2 + 1.351
AGND
VDD/2
VDD/2 – 0.036
VDD/2 + 0.036
V
VREFLO
Ref Low
VDD/2 – Bandgap
V
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
VDD/2 + Bandgap
VDD/2 – 1.357 VDD/2 – 1.298 VDD/2 – 1.228
VDD/2 + 1.219 VDD/2 + 1.293 VDD/2 + 1.353
AGND
VDD/2
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 0.037 VDD/2 – 0.001 VDD/2 + 0.036
VDD/2 – 1.359 VDD/2 – 1.299 VDD/2 – 1.229
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.092
0.011
0.064
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.031
0.007
0.056
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.078
0.008
0.063
V
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.031
0.004
0.043
V
RefPower = medium VREFHI
Opamp bias = high
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.073
0.006
0.062
V
RefPower = high
Opamp bias = low
0b001
Symbol
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
P2[4]
P2[4]
VDD/2
P2[4]
P2[4]
P2[4]
V
V
V
–
–
AGND
P2[4]
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.032
0.003
0.038
V
RefPower = medium VREFHI
Opamp bias = low
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.073
0.006
0.062
V
AGND
P2[4]
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 1.3 V)
Document Number: 001-53754 Rev. *D
P2[4]
P2[4]
P2[4]
V
VREFLO
VREFLO
P2[4]
P2[4]
V
VAGND
VAGND
P2[4]
VDD/2
P2[4]
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.034
0.002
0.037
–
–
V
Page 19 of 46
[+] Feedback
CY8C24894
Table 12. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
0b010
Reference Power
Settings
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b011
Reference
Description
VREFHI
Ref High
VDD
Min
Typ
Max
Units
VDD – 0.037
VDD – 0.007
VDD
V
VAGND
AGND
VDD/2
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.029
V
VREFHI
Ref High
VDD
VDD – 0.034
VDD – 0.006
VDD
V
VDD/2 – 0.036 VDD/2 – 0.001 VDD/2 + 0.036
V
VAGND
AGND
VDD/2
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.024
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
VDD
VDD – 0.032
VDD – 0.005
VDD
V
AGND
VDD/2
VREFLO
Ref Low
VSS
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
VDD
AGND
VDD/2
VREFLO
Ref Low
VSS
VREFHI
Ref High
3 × Bandgap
3.760
3.884
4.006
V
VAGND
AGND
2 × Bandgap
2.522
2.593
2.669
V
VREFLO
Ref Low
Bandgap
1.252
1.299
1.342
V
VREFHI
Ref High
3 × Bandgap
3.766
3.887
4.010
V
VAGND
AGND
2 × Bandgap
2.523
2.594
2.670
V
V
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b100
Symbol
VDD/2 – 0.036 VDD/2 – 0.001 VDD/2 + 0.035
VDD/2 – 0.036 VDD/2 – 0.001 VDD/2 + 0.035
VSS
VSS + 0.003
VSS + 0.022
VDD – 0.031
VDD – 0.005
VDD
VDD/2 – 0.037 VDD/2 – 0.001 VDD/2 + 0.035
VSS
VSS + 0.003
VSS + 0.020
V
V
V
V
V
V
VREFLO
Ref Low
Bandgap
1.252
1.297
1.342
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
3 × Bandgap
3.769
3.888
4.013
V
AGND
2 × Bandgap
2.523
2.594
2.671
V
V
VREFLO
Ref Low
Bandgap
1.251
1.296
1.343
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
3 × Bandgap
3.769
3.889
4.015
V
AGND
2 × Bandgap
2.523
2.595
2.671
V
VREFLO
Ref Low
Bandgap
VREFHI
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
VAGND
AGND
2 × Bandgap
VREFLO
Ref Low
VREFHI
Ref High
VAGND
AGND
2 × Bandgap
2.523
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.523 – P2[6]
RefPower = medium VREFHI
Opamp bias = high
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.493 – P2[6]
2.588 – P2[6]
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
1.251
1.296
1.344
V
2.483 – P2[6]
2.582 – P2[6]
2.674 – P2[6]
V
2.522
2.593
2.669
V
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.524 – P2[6]
2.600 – P2[6]
2.676 – P2[6]
V
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.490 – P2[6]
2.586 – P2[6]
2.679 – P2[6]
V
2.594
2.669
V
2.598 – P2[6]
2.675 – P2[6]
V
2.682 – P2[6]
V
VAGND
AGND
2 × Bandgap
2.523
2.594
2.670
V
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.523 – P2[6]
2.597 – P2[6]
2.675 – P2[6]
V
RefPower = medium VREFHI
Opamp bias = low
Ref High
2 × Bandgap + P2[6]
(P2[6] = 1.3 V)
2.494 – P2[6]
2.589 – P2[6]
2.685 – P2[6]
V
VAGND
AGND
2 × Bandgap
2.523
2.595
2.671
V
VREFLO
Ref Low
2 × Bandgap – P2[6]
(P2[6] = 1.3 V)
2.522 – P2[6]
2.596 – P2[6]
2.676 – P2[6]
V
Document Number: 001-53754 Rev. *D
Page 20 of 46
[+] Feedback
CY8C24894
Table 12. 5-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
0b101
Reference Power
Settings
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b110
Reference
Description
Min
Typ
Max
Units
P2[4] + 1.218
P2[4] + 1.291
P2[4] + 1.354
V
P2[4]
P2[4]
P2[4]
–
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.335
P2[4] – 1.294
P2[4] – 1.237
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.221
P2[4] + 1.293
P2[4] + 1.358
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.337
P2[4] – 1.297
P2[4] – 1.243
V
RefPower = medium VREFHI
Opamp bias = high
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.222
P2[4] + 1.294
P2[4] + 1.360
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.338
P2[4] – 1.298
P2[4] – 1.245
V
RefPower = medium VREFHI
Opamp bias = low
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.221
P2[4] + 1.294
P2[4] + 1.362
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.340
P2[4] – 1.298
P2[4] – 1.245
V
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b111
Symbol
VREFHI
Ref High
2 × Bandgap
2.513
2.593
2.672
V
VAGND
AGND
Bandgap
1.264
1.302
1.340
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.008
VSS + 0.038
V
VREFHI
Ref High
2 × Bandgap
2.514
2.593
2.674
V
VAGND
AGND
Bandgap
1.264
1.301
1.340
V
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.028
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
2 × Bandgap
2.514
2.593
2.676
V
AGND
Bandgap
1.264
1.301
1.340
V
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.024
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
2 × Bandgap
2.514
2.593
2.677
V
AGND
Bandgap
1.264
1.300
1.340
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.021
V
VREFHI
Ref High
3.2 × Bandgap
4.028
4.144
4.242
V
VAGND
AGND
1.6 × Bandgap
2.028
2.076
2.125
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.008
VSS + 0.034
V
VREFHI
Ref High
3.2 × Bandgap
4.032
4.142
4.245
V
VAGND
AGND
1.6 × Bandgap
2.029
2.076
2.126
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.005
VSS + 0.025
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
3.2 × Bandgap
4.034
4.143
4.247
V
AGND
1.6 × Bandgap
2.029
2.076
2.126
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.021
V
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
3.2 × Bandgap
4.036
4.144
4.249
V
AGND
1.6 × Bandgap
2.029
2.076
2.126
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.019
V
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
Document Number: 001-53754 Rev. *D
Page 21 of 46
[+] Feedback
CY8C24894
Table 13. 3.3-V DC Analog Reference Specifications
Reference
ARF_CR
[5:3]
0b000
Reference Power
Settings
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b001
Reference
Description
Min
Typ
Max
Units
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 + 1.200 VDD/2 + 1.290 VDD/2 + 1.365
VAGND
AGND
VDD/2
VDD/2 – 0.030
VDD/2 + 0.034
V
VREFLO
Ref Low
VDD/2 – Bandgap
V
VREFHI
Ref High
VDD/2 + Bandgap
VDD/2 – 1.346 VDD/2 – 1.292 VDD/2 – 1.208
VDD/2 + 1.196 VDD/2 + 1.292 VDD/2 + 1.374
VAGND
AGND
VDD/2
VDD/2 – 0.029
VDD/2 + 0.031
V
VDD/2
VDD/2
V
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.349 VDD/2 – 1.295 VDD/2 – 1.227
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
VDD/2 + Bandgap
VDD/2 + 1.204 VDD/2 + 1.293 VDD/2 + 1.369
V
AGND
VDD/2
VDD/2 – 0.030
VDD/2 + 0.030
V
VDD/2
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.351 VDD/2 – 1.297 VDD/2 – 1.229
V
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
VDD/2 + Bandgap
V
AGND
VDD/2
VDD/2 + 1.189 VDD/2 + 1.294 VDD/2 + 1.384
VDD/2 – 0.032
VDD/2
VDD/2 + 0.029
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
0b010
Symbol
V
VREFLO
Ref Low
VDD/2 – Bandgap
VDD/2 – 1.353 VDD/2 – 1.297 VDD/2 – 1.230
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.105
0.008
0.095
V
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.035
0.006
0.053
V
VREFHI
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.094
0.005
0.073
V
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
P2[4]
–
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] – P2[4] – P2[6] + P2[4] – P2[6] +
0.033
0.002
0.042
V
–
RefPower = medium VREFHI
Opamp bias = high
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.094
0.003
0.075
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] – P2[6] –
0.035
P2[4] – P2[6]
P2[4] – P2[6] +
0.038
V
RefPower = medium VREFHI
Opamp bias = low
Ref High
P2[4]+P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
P2[4] + P2[6] – P2[4] + P2[6] – P2[4] + P2[6] +
0.095
0.003
0.080
V
VAGND
AGND
P2[4]
VREFLO
Ref Low
P2[4]–P2[6] (P2[4] =
VDD/2, P2[6] = 0.5 V)
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
VREFHI
Ref High
VDD
VAGND
AGND
VDD/2
VREFLO
Ref Low
VSS
VREFHI
Ref High
VDD
VAGND
AGND
VDD/2
P2[4]
P2[4]
P2[4]
–
P2[4] – P2[6] –
0.038
P2[4] – P2[6]
P2[4] – P2[6] +
0.038
V
V
VDD – 0.119
VDD – 0.005
VDD
VDD/2 – 0.028
VDD/2
VDD/2 + 0.029
V
VSS
VSS + 0.004
VSS + 0.022
V
VDD – 0.131
VDD – 0.004
VDD
V
VDD/2 – 0.028
VDD/2
VDD/2 + 0.028
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.021
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
VDD
VDD – 0.111
VDD – 0.003
VDD
V
AGND
VDD/2
VDD/2 – 0.029
VDD/2
VDD/2 + 0.028
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.002
VSS + 0.017
V
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
VDD
VDD – 0.128
VDD – 0.003
VDD
V
AGND
VDD/2
VDD/2 – 0.029
VDD/2
VDD/2 + 0.029
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.002
VSS + 0.019
V
Document Number: 001-53754 Rev. *D
Page 22 of 46
[+] Feedback
CY8C24894
Table 13. 3.3-V DC Analog Reference Specifications (continued)
Reference
ARF_CR
[5:3]
Reference Power
Settings
Symbol
Reference
Description
Min
Typ
Max
Units
0b011
All power settings.
–
Not allowed for 3.3 V.
–
–
–
–
–
–
0b100
All power settings.
–
Not allowed for 3.3 V.
–
–
–
–
–
–
0b101
RefPower = high
Opamp bias = high
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.214
P2[4] + 1.291
P2[4] + 1.359
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.335
P2[4] – 1.292
P2[4] – 1.200
V
VREFHI
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.219
P2[4] + 1.293
P2[4] + 1.357
V
RefPower = high
Opamp bias = low
0b110
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.335
P2[4] – 1.295
P2[4] – 1.243
V
RefPower = medium VREFHI
Opamp bias = high
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.222
P2[4] + 1.294
P2[4] + 1.356
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.337
P2[4] – 1.296
P2[4] – 1.244
V
RefPower = medium VREFHI
Opamp bias = low
Ref High
P2[4] + Bandgap
(P2[4] = VDD/2)
P2[4] + 1.224
P2[4] + 1.295
P2[4] + 1.355
V
VAGND
AGND
P2[4]
P2[4]
P2[4]
P2[4]
–
VREFLO
Ref Low
P2[4] – Bandgap
(P2[4] = VDD/2)
P2[4] – 1.339
P2[4] – 1.297
P2[4] – 1.244
V
V
RefPower = high
Opamp bias = high
RefPower = high
Opamp bias = low
VREFHI
Ref High
2 × Bandgap
2.510
2.595
2.655
VAGND
AGND
Bandgap
1.276
1.301
1.332
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.006
VSS + 0.031
V
VREFHI
Ref High
2 × Bandgap
2.513
2.594
2.656
V
VAGND
AGND
Bandgap
1.275
1.301
1.331
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.004
VSS + 0.021
V
RefPower = medium VREFHI
Opamp bias = high V
AGND
Ref High
2 × Bandgap
2.516
2.595
2.657
V
AGND
Bandgap
1.275
1.301
1.331
V
VREFLO
Ref Low
VSS
VSS
VSS + 0.003
VSS + 0.017
V
RefPower = medium VREFHI
Opamp bias = low
VAGND
Ref High
2 × Bandgap
2.520
2.595
2.658
V
AGND
Bandgap
1.275
1.300
1.331
V
VSS
VSS + 0.002
VSS + 0.015
V
–
–
–
–
VREFLO
0b111
All power settings.
–
Not allowed for 3.3 V.
Document Number: 001-53754 Rev. *D
Ref Low
VSS
–
–
Page 23 of 46
[+] Feedback
CY8C24894
DC Analog PSoC Block Specifications
Table 14 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 14. DC Analog PSoC Block Specifications
Symbol
Description
RCT
Resistor unit value (continuous time)
CSC
Capacitor unit value (switched capacitor)
Min
–
–
Typ
12.2
80
Max
–
–
Units
kΩ
fF
Notes
DC POR and LVD Specifications
Table 15 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V or 3.3 V at 25 °C and are
for design guidance only.
Note The bits PORLEV and VM in the table below refer to bits in the VLT_CR register. See the PSoC Technical Reference Manual
for more information on the VLT_CR register.
Table 15. DC POR and LVD Specifications
Symbol
Description
Min
Typ
Units
Notes
–
–
–
V
V
V
VDD must be greater than or equal
to 2.5 V during startup, reset from
the XRES pin, or reset from
watchdog.
92
0
0
–
–
–
mV
mV
mV
2.92
3.02
3.13
4.00
4.48
4.64
4.73
4.81
3.02[6]
3.12
3.24
4.12
4.62
4.78[7]
4.87
4.96
V
V
V
V
V
V
V
V
VPPOR0
VPPOR1
VPPOR2
VDD Value for PPOR Trip (negative ramp)
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
–
–
–
2.82
4.39
4.55
VPH0
VPH1
VPH2
PPOR Hysteresis
PORLEV[1:0] = 00b
PORLEV[1:0] = 01b
PORLEV[1:0] = 10b
–
–
–
VLVD0
VLVD1
VLVD2
VLVD3
VLVD4
VLVD5
VLVD6
VLVD7
VDD Value for LVD Trip
VM[2:0] = 000b
VM[2:0] = 001b
VM[2:0] = 010b
VM[2:0] = 011b
VM[2:0] = 100b
VM[2:0] = 101b
VM[2:0] = 110b
VM[2:0] = 111b
2.86
2.96
3.07
3.92
4.39
4.55
4.63
4.72
Max
Notes
6. Always greater than 50 mV above PPOR (PORLEV = 00) for falling supply.
7. Always greater than 50 mV above PPOR (PORLEV = 10) for falling supply.
Document Number: 001-53754 Rev. *D
Page 24 of 46
[+] Feedback
CY8C24894
DC Programming Specifications
Table 16 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 16. DC Programming Specifications
Symbol
VDDP
Description
VDD for programming and erase
Min
4.5
Typ
5.0
Max
5.5
Units
V
VDDLV
Low VDD for verify
3.0
3.1
3.2
V
VDDHV
High VDD for verify
5.1
5.2
5.3
V
3.0
–
5.25
V
15
–
–
–
30
0.8
–
0.2
mA
V
V
mA
–
1.5
mA
–
0.75
V
–
VDD
V
–
–
–
–
–
–
–
–
Years
VDDIWRITE Supply voltage for flash write operation
IDDP
VILP
VIHP
IILP
Supply current during programming or verify
–
Input low voltage during programming or verify
–
Input high voltage during programming or verify
2.1
Input current when applying VILP to P1[0] or
–
P1[1] during programming or verify
IIHP
Input current when applying VIHP to P1[0] or
–
P1[1] during programming or verify
VOLV
Output low voltage during programming or
–
verify
VOHV
Output high voltage during programming or
VDD – 1.0
verify
FlashENPB Flash endurance (per block)[8, 9]
1,000
FlashENT Flash endurance (total)[9, 10]
256,000
FlashDR
Flash data retention[9]
10
Notes
This specification applies to
the functional requirements of
external programmer tools
This specification applies to
the functional requirements of
external programmer tools
This specification applies to
the functional requirements of
external programmer tools
This specification applies to
this device when it is
executing internal flash writes
Driving internal pull-down
resistor.
Driving internal pull-down
resistor.
Erase/write cycles per block.
Erase/write cycles.
Notes
8. The erase/write cycle limit per block (FlashENPB) is only guaranteed if the device operates within one voltage range. Voltage ranges are 3.0 V to 3.6 V and 4.75 V to
5.25 V.
9. For the full temperature range, the user must employ a temperature sensor user module (FlashTemp) or other temperature sensor, and feed the result to the temperature
argument before writing. Refer to the Flash APIs Application Note AN2015 for more information.
10. The maximum total number of allowed erase/write cycles is the minimum FlashENPB value multiplied by the number of flash blocks in the device.
Document Number: 001-53754 Rev. *D
Page 25 of 46
[+] Feedback
CY8C24894
AC Electrical Characteristics
AC Chip-Level Specifications
Table 17 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 17. AC Chip-Level Specifications
Symbol
F32K1
Description
IMO frequency for 24 MHz (5 V
nominal)
IMO frequency for 24 MHz (3.3 V
nominal)
CPU frequency (5 V nominal)
CPU frequency (3.3 V nominal)
Digital PSoC block frequency (5 V
nominal)
Digital PSoC block frequency (3.3 V
nominal)
ILO frequency
F32KU
ILO untrimmed frequency
FIMO245V
FIMO243V
FCPU1
FCPU2
FBLK5
FBLK3
tXRST
DC24M
DCILO
Step24M
Fout48M
FMAX
External reset pulse width
24 MHz duty cycle
ILO duty cycle
24 MHz trim step size
48 MHz output frequency
Maximum frequency of signal on row
input or row output.
SRPOWERUP Power supply slew rate
tPOWERUP
Time between end of POR state and
CPU code execution
tJIT_IMO[13]
24 MHz IMO cycle-to-cycle jitter (RMS)
24 MHz IMO long term N cycle-to-cycle
jitter (RMS)
24 MHz IMO period jitter (RMS)
Min
23.04[11]
Typ
24
Max
24.96[11]
Units
Notes
MHz Trimmed for 5 V operation using
factory trim values.
MHz Trimmed for 3.3 V operation using
factory trim values.
MHz SLIMO mode = 0.
MHz SLIMO mode = 0.
MHz Refer to the AC Digital Block
Specifications.
MHz Refer to the AC Digital Block
Specifications.
kHz This specification applies when
the ILO has been trimmed.
kHz After a reset and before the M8C
processor starts to execute, the
ILO is not trimmed.
µs
%
%
kHz
MHz 4.75 V ≤ VDD ≤ 5.25 V
MHz
22.08[11]
24
25.92[11]
0.090[11]
0.086[11]
0
24
12
48
24.96[11]
12.96[11]
49.92[11,12]
0
24
25.92[11,12]
15
32
64
5
–
100
10
40
20
–
46.08[11]
–
–
50
50
50
48
–
–
60
80
–
49.92[11]
12.96[11]
–
–
–
16
250
100
V/ms
ms
–
–
200
900
1200
6000
ps
ps
–
200
900
ps
VDD slew rate during power-up.
Power-up from 0 V.
N = 32
Notes
11. Accuracy derived from IMO with appropriate trim for VDD range.
12. See the individual user module datasheets for information on maximum frequencies for user modules.
13. Refer to Cypress Jitter Specifications application note, Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 for more information.
Document Number: 001-53754 Rev. *D
Page 26 of 46
[+] Feedback
CY8C24894
AC GPIO Specifications
Table 18 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 18. AC GPIO Specifications
Symbol
FGPIO
tRISEF
tFALLF
tRISES
tFALLS
Description
GPIO operating frequency
Rise time, normal strong mode, Cload = 50 pF
Fall time, normal strong mode, Cload = 50 pF
Rise time, slow strong mode, Cload = 50 pF
Fall time, slow strong mode, Cload = 50 pF
Min
0
3
2
10
10
Typ
–
–
–
27
22
Max
12.96[14]
18
18
–
–
Units
MHz
ns
ns
ns
ns
Notes
Normal Strong Mode
VDD = 4.5 to 5.25 V, 10% to 90%
VDD = 4.5 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
VDD = 3 to 5.25 V, 10% to 90%
Figure 5. GPIO Timing Diagram
90%
G PIO
Pin
O utput
Voltage
10%
tRISEF
TRiseF
tRISES
TRiseS
tFALLF
TFallF
tFALLS
TFallS
Note
14. Specification derived from the accuracy of the Internal Main Oscillator (IMO) with appropriate trim for VDD range.
Document Number: 001-53754 Rev. *D
Page 27 of 46
[+] Feedback
CY8C24894
AC Operational Amplifier Specifications
Table 19 and Table 20 list the guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to
5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V
at 25 °C and are for design guidance only.
Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block.
Power = high and Opamp bias = high is not supported at 3.3 V.
Table 19. 5-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time from 80% of ΔV to 0.1% of ΔV
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Falling settling time from 20% of ΔV to 0.1% of ΔV
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Rising slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Falling slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Gain bandwidth product
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Power = high, Opamp bias = high
Noise at 1 kHz (Power = medium, Opamp bias = high)
Min
Typ
Max
Units
–
–
–
–
–
–
3.9
0.72
0.62
µs
µs
µs
–
–
–
–
–
–
5.9
0.92
0.72
µs
µs
µs
0.15
1.7
6.5
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.01
0.5
4.0
–
–
–
–
–
–
V/µs
V/µs
V/µs
0.75
3.1
5.4
–
–
–
–
100
–
–
–
–
MHz
MHz
MHz
nV/rt-Hz
Min
Typ
Max
Units
–
–
–
–
3.92
0.72
µs
µs
–
–
–
–
5.41
0.72
µs
µs
0.31
2.7
–
–
–
–
V/µs
V/µs
0.24
1.8
–
–
–
–
V/µs
V/µs
0.67
2.8
–
–
–
100
–
–
–
MHz
MHz
nV/rt-Hz
Table 20. 3.3-V AC Operational Amplifier Specifications
Symbol
tROA
tSOA
SRROA
SRFOA
BWOA
ENOA
Description
Rising settling time from 80% of ΔV to 0.1% of ΔV
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Falling settling time from 20% of ΔV to 0.1% of ΔV
(10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Rising slew rate (20% to 80%) (10 pF load, unity gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Falling slew rate (20% to 80%) (10 pF load, Unity Gain)
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Gain bandwidth product
Power = low, Opamp bias = low
Power = medium, Opamp bias = high
Noise at 1 kHz (Power = medium, Opamp bias = high)
Document Number: 001-53754 Rev. *D
Page 28 of 46
[+] Feedback
CY8C24894
When bypassed by a capacitor on P2[4], the noise of the analog ground signal distributed to each block is reduced by a factor of up
to 5 (14 dB). This is at frequencies above the corner frequency defined by the on-chip 8.1 kΩ resistance and the external capacitor.
Figure 6. Typical AGND Noise with P2[4] Bypass
nV/rtHz
10000
0
0.01
0.1
1.0
10
1000
100
0.001
0.01
0.1 Freq (kHz)
1
10
100
At low frequencies, the opamp noise is proportional to 1/f, power independent, and determined by device geometry. At high
frequencies, increased power level reduces the noise spectrum level.
Figure 7. Typical Opamp Noise
nV/rtHz
10000
PH_BH
PH_BL
PM_BL
PL_BL
1000
100
10
0.001
Document Number: 001-53754 Rev. *D
0.01
0.1
Freq (kHz)
1
10
100
Page 29 of 46
[+] Feedback
CY8C24894
AC Low Power Comparator Specifications
Table 21 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V at 25 °C and are for design
guidance only.
Table 21. AC Low Power Comparator Specifications
Symbol
Description
tRLPC
LPC response time
Min
–
Typ
–
Max
50
Units
Notes
μs
≥ 50 mV overdrive comparator
reference set within VREFLPC.
AC Digital Block Specifications
Table 22 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 22. AC Digital Block Specifications
Function
Description
All
Block input clock frequency
functions
VDD ≥ 4.75 V
VDD < 4.75 V
Timer
Input clock frequency
No capture, VDD ≥ 4.75 V
No capture, VDD < 4.75 V
With capture
Capture pulse width
Counter Input clock frequency
No enable input, VDD ≥ 4.75 V
No enable input, VDD < 4.75 V
With enable input
Enable input pulse width
Dead
Kill pulse width
Band
Asynchronous restart mode
Synchronous restart mode
Disable mode
Input clock frequency
VDD ≥ 4.75 V
VDD < 4.75 V
CRCPRS Input clock frequency
(PRS
VDD ≥ 4.75 V
Mode)
VDD < 4.75 V
CRCPRS Input clock frequency
(CRC
Mode)
SPIM
Input clock frequency
SPIS
Transmitter
Input clock (SCLK) frequency
Width of SS_Negated between transmissions
Input Clock Frequency
VDD ≥ 4.75 V, 2 stop bits
VDD ≥ 4.75 V, 1 stop bit
VDD < 4.75 V
Min
Typ
Max
Units
–
–
–
–
49.92[15]
25.92[15]
MHz
MHz
–
–
–
50[16]
–
–
–
–
49.92[15]
25.92[15]
25.92[15]
–
MHz
MHz
MHz
ns
–
–
–
50[16]
–
–
–
–
49.92[15]
25.92[15]
25.92[15]
–
MHz
MHz
MHz
ns
20
50[16]
50[16]
–
–
–
–
–
–
ns
ns
ns
–
–
–
–
49.92[15]
25.92[15]
MHz
MHz
–
–
–
–
–
–
49.92[15]
25.92[15]
25.92[15]
MHz
MHz
MHz
–
–
8.64[15]
MHz
–
–
4.32[15]
MHz
50[16]
–
–
ns
–
–
–
–
–
–
49.92[15]
25.92[15]
25.92[15]
MHz
MHz
MHz
Notes
The SPI serial clock (SCLK)
frequency is equal to the input
clock frequency divided by 2.
The input clock is the SPI SCLK in
SPIS mode.
The baud rate is equal to the input
clock frequency divided by 8.
Notes
15. Accuracy derived from IMO with appropriate trim for VDD range.
16. 50 ns minimum input pulse width is based on the input synchronizers running at 24 MHz (42 ns nominal period).
Document Number: 001-53754 Rev. *D
Page 30 of 46
[+] Feedback
CY8C24894
Table 22. AC Digital Block Specifications (continued)
Function
Description
Receiver Input clock frequency
VDD ≥ 4.75 V, 2 stop bits
VDD ≥ 4.75 V, 1 stop bit
VDD < 4.75 V
Min
Typ
Max
Units
–
–
–
–
–
–
49.92[15]
25.92[15]
25.92[15]
MHz
MHz
MHz
Notes
The baud rate is equal to the input
clock frequency divided by 8.
AC External Clock Specifications
Table 23 list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40 °C
≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are for
design guidance only.
Table 23. AC External Clock Specifications
Symbol
Description
Min
Typ
Max
Units
FOSCEXT
Frequency
0
–
24.24
MHz
–
High period
20.5
–
–
ns
–
Low period
20.5
–
–
ns
–
Power-up IMO to switch
150
–
–
μs
Notes
AC Analog Output Buffer Specifications
Table 24 and Table 25 on page 32 list the guaranteed maximum and minimum specifications for the voltage and temperature ranges:
4.75 V to 5.25 V and –40 °C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V
and 3.3 V at 25 °C and are for design guidance only.
Table 24. 5-V AC Analog Output Buffer Specifications
Symbol
Description
tROB
Rising settling time to 0.1%, 1 V step, 100pF load
Power = low
Power = high
tSOB
Falling settling time to 0.1%, 1 V step, 100pF load
Power = low
Power = high
SRROB
Rising slew rate (20% to 80%), 1 V step, 100 pF load
Power = low
Power = high
SRFOB
Falling slew rate (80% to 20%), 1 V step, 100 pF load
Power = low
Power = high
BWOBSS Small signal bandwidth, 20 mVpp, 3 dB BW, 100 pF load
Power = low
Power = high
BWOBLS Large signal bandwidth, 1 Vpp, 3 dB BW, 100 pF load
Power = low
Power = high
Document Number: 001-53754 Rev. *D
Min
Typ
Max
Units
–
–
–
–
2.5
2.5
μs
μs
–
–
–
–
2.2
2.2
μs
μs
0.65
0.65
–
–
–
–
V/μs
V/μs
0.65
0.65
–
–
–
–
V/μs
V/μs
0.8
0.8
–
–
–
–
MHz
MHz
300
300
–
–
–
–
kHz
kHz
Notes
Page 31 of 46
[+] Feedback
CY8C24894
Table 25. 3.3-V AC Analog Output Buffer Specifications
Symbol
Description
tROB
Rising settling time to 0.1%, 1 V step, 100 pF load
Power = low
Power = high
tSOB
Falling settling time to 0.1%, 1 V step, 100 pF load
Power = low
Power = high
SRROB
Rising slew rate (20% to 80%), 1 V step, 100 pF load
Power = low
Power = high
SRFOB
Falling slew rate (80% to 20%), 1 V step, 100 pF load
Power = low
Power = high
BWOBSS Small signal bandwidth, 20 mVpp, 3 dB BW, 100 pF load
Power = low
Power = high
BWOBLS Large signal bandwidth, 1 Vpp, 3 dB BW, 100 pF load
Power = low
Power = high
Min
Typ
Max
Units
–
–
–
–
3.8
3.8
μs
μs
–
–
–
–
2.6
2.6
μs
μs
0.5
0.5
–
–
–
–
V/μs
V/μs
0.5
0.5
–
–
–
–
V/μs
V/μs
0.7
0.7
–
–
–
–
MHz
MHz
200
200
–
–
–
–
kHz
kHz
Notes
AC Programming Specifications
Table 26 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 26. AC Programming Specifications
Symbol
tRSCLK
tFSCLK
tSSCLK
tHSCLK
FSCLK
tERASEB
tWRITE
tDSCLK
tDSCLK3
tPRGH
tPRGC
Description
Rise time of SCLK
Fall time of SCLK
Data setup time to falling edge of SCLK
Data hold time from falling edge of SCLK
Frequency of SCLK
Flash erase time (block)
Flash block write time
Data out delay from falling edge of SCLK
Data out delay from falling edge of SCLK
Total flash block program time (tERASEB + tWRITE), hot
Total flash block program time (tERASEB + tWRITE), cold
Min
1
1
40
40
0
–
–
–
–
–
–
Typ
–
–
–
–
–
10
40
–
–
–
–
Max
20
20
–
–
8
40[17]
160[17]
45
50
100[17]
200[17]
Units
ns
ns
ns
ns
MHz
ms
ms
ns
ns
ms
ms
Notes
VDD > 3.6 V
3.0 V ≤ VDD ≤ 3.6 V
TJ ≥ 0 °C
TJ < 0 °C
Note
17. For the full temperature range, the user must employ a temperature sensor user module (FlashTemp) or other temperature sensor, and feed the result to the temperature
argument before writing. Refer to the Flash APIs Application Note AN2015 for more information.
Document Number: 001-53754 Rev. *D
Page 32 of 46
[+] Feedback
CY8C24894
AC I2C Specifications
Table 27 lists guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75 V to 5.25 V and –40
°C ≤ TA ≤ 85 °C, or 3.0 V to 3.6 V and –40 °C ≤ TA ≤ 85 °C, respectively. Typical parameters apply to 5 V and 3.3 V at 25 °C and are
for design guidance only.
Table 27. AC Characteristics of the I2C SDA and SCL Pins for VDD
Symbol
FSCLI2C
tHDSTAI2C
tLOWI2C
tHIGHI2C
tSUSTAI2C
tHDDATI2C
tSUDATI2C
tSUSTOI2C
tBUFI2C
tSPI2C
Description
SCL clock frequency
Hold time (repeated) START condition. After
this period, the first clock pulse is generated.
LOW period of the SCL clock
HIGH period of the SCL clock
Setup time for a repeated START condition
Data hold time
Data setup time
Setup time for STOP condition
Bus free time between a stop and start
condition
Pulse width of spikes are suppressed by the
input filter.
Standard Mode
Min
Max
0
100[18]
4.0
–
Fast Mode
Min
Max
0
400[18]
0.6
–
Units
Notes
kHz
μs
4.7
4.0
4.7
0
250
4.0
4.7
–
–
–
–
–
–
–
1.3
0.6
0.6
0
100[19]
0.6
1.3
–
–
–
–
–
–
–
μs
μs
μs
μs
ns
μs
μs
–
–
0
50
ns
Figure 8. Definition for Timing for Fast/Standard Mode on the I2C Bus
I2C_SDA
tSUDATI2C
tSPI2C
tHDDATI2C tSUSTAI2C
tHDSTAI2C
tBUFI2C
I2C_SCL
tHIGHI2C
S
START Condition
tLOWI2C
tSUSTOI2C
Sr
Repeated START Condition
P
S
STOP Condition
Notes
18. FSCLI2C is derived from SysClk of the PSoC. This specification assumes that SysClk is operating at 24 MHz, nominal. If SysClk is at a lower frequency, then the FSCLI2C
specification adjusts accordingly.
19. A Fast-Mode I2C-bus device can be used in a Standard-Mode I2C-bus system, but the requirement tSUDATI2C ≥ 250 ns must then be met. This is automatically the
case if the device does not stretch the LOW period of the SCL signal. If such device does stretch the LOW period of the SCL signal, it must output the next data bit to
the SDA line trmax + tSUDATI2C = 1000 + 250 = 1250 ns (according to the Standard-Mode I2C-bus specification) before the SCL line is released.
Document Number: 001-53754 Rev. *D
Page 33 of 46
[+] Feedback
CY8C24894
Packaging Information
This section illustrates the package specification for the CY8C24x94 PSoC devices, along with the thermal impedance for the package
and solder reflow peak temperatures.
Note Emulation tools may require a larger area on the target PCB than the chip's footprint. For a detailed description of the emulation
tools' dimensions, refer to the emulator pod drawings at http://www.cypress.com.
Figure 9. 56-Pin (8 × 8 mm) QFN (Punched)
SOLDERABLE
EXPOSED
PAD
001-12921 *B
Important Note
■
For information on the preferred dimensions for mounting QFN packages, see the following application note, Application Notes for
Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages available at http://www.amkor.com.
■
Pinned vias for thermal conduction are not required for the low power PSoC device.
Thermal Impedances
Solder Reflow Specifications
Table 28. Thermal Impedance per Package
Table 29 shows the solder reflow temperature limits that must not
be exceeded.
Package
[21]
56-pin QFN
Typical θJA [20]
Typical θJC
19 °C/W
1.7 °C/W
Table 29. Solder Reflow Specifications
Package
Maximum Peak
Temperature (TC)
Maximum Time
above TC – 5 °C
56-pin QFN
260 °C
30 seconds
Notes
20. TJ = TA + Power × θJA.
21. To achieve the thermal impedance specified for the QFN package, refer to the application notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF)
Packages available at http://www.amkor.com.
Document Number: 001-53754 Rev. *D
Page 34 of 46
[+] Feedback
CY8C24894
Tape and Reel Information
Figure 10. 56-Pin (8 × 8 mm) QFN (Punched) Carrier Tape Drawing
51-51165 *B
Table 30. Tape and Reel Specifications
Package
Cover Tape
Width (mm)
Hub Size
(inches)
Minimum Leading
Empty Pockets
56-Pin QFN
13.1
7
42
Document Number: 001-53754 Rev. *D
Minimum
Trailing Empty
Pockets
25
Standard Full Reel
Quantity
2000
Page 35 of 46
[+] Feedback
CY8C24894
Development Tool Selection
Software
PSoC Designer
At the core of the PSoC development software suite is PSoC
Designer, used to generate PSoC firmware applications. PSoC
Designer is available free of charge at http://www.cypress.com
and includes a free C compiler.
The Universal CapSense Controller Kit is designed for easy
prototyping and debug of CapSense designs with pre-defined
control circuitry and plug-in hardware. The CY3280-24X94 kit
contains no plug-in hardware. Therefore, it is only usable if
plug-in hardware is purchased as part of the CY3280-BK1 kit or
other separate kits. The kit includes:
■
CY3280-24X94 Universal CapSense Controller Board
PSoC Programmer
■
CY3240-I2USB Bridge Board
Flexible enough to be used on the bench in development, yet
suitable for factory programming, PSoC Programmer works
either as a standalone programming application or it can operate
directly from PSoC Designer or PSoC Express. PSoC
Programmer software is compatible with both PSoC ICE-Cube
In-Circuit Emulator and PSoC MiniProg. PSoC programmer is
available free of charge at http://www.cypress.com.
■
CY3210 PSoC MiniProg1 Programmer
■
CY3280-24X94 Quick Start
■
USB Retractable Cable (A to mini-B)
■
PSoC Express Installation CD
■
PSoC Designer and PSoC Programmer CD
■
CY3280-24X94 Universal CapSense Controller Kit CD
Development Kits
All development kits can be purchased from the Cypress Online
Store. The online store also has the most up to date information
on kit contents, descriptions, and availability.
CY3215-DK Basic Development Kit
The CY3215-DK is for prototyping and development with PSoC
Designer. This kit supports in-circuit emulation and the software
interface allows users to run, halt, and single step the processor
and view the contents of specific memory locations. Advanced
emulation features are also supported through PSoC Designer.
The kit includes:
Evaluation Tools
All evaluation tools can be purchased from the Cypress Online
Store. The online store also has the most up to date information
on kit contents, descriptions, and availability.
CY3210-PSoCEval1
■
ICE-Cube Unit
The CY3210-PSoCEval1 kit features an evaluation board and
the MiniProg1 programming unit. The evaluation board includes
an LCD module, potentiometer, LEDs, and plenty of breadboarding space to meet all of your evaluation needs. The kit
includes:
■
28-Pin PDIP Emulation Pod for CY8C29466-24PXI
■
Evaluation Board with LCD Module
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Samples (two)
■
MiniProg Programming Unit
■
PSoC Designer Software CD
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Sample (2)
■
ISSP Cable
■
PSoC Designer Software CD
■
MiniEval Socket Programming and Evaluation board
■
Getting Started Guide
■
Backward Compatibility Cable (for connecting to legacy Pods)
■
USB 2.0 Cable
■
Universal 110/220 Power Supply (12 V)
CY3210-24X94 Evaluation Pod (EvalPod)
■
European Plug Adapter
■
USB 2.0 Cable
■
Getting Started Guide
■
Development Kit Registration form
PSoC EvalPods are pods that connect to the ICE In-Circuit
Emulator (CY3215-DK kit) to allow debugging capability. They
can also function as a standalone device without debugging
capability. The EvalPod has a 28-pin DIP footprint on the bottom
for easy connection to development kits or other hardware. The
top of the EvalPod has prototyping headers for easy connection
to the device's pins. CY3210-24X94 provides evaluation of the
CY8C24x94 PSoC device family.
CY3280-24X94 Universal CapSense Controller Board
The CY3280-24X94 Controller Board is an additional controller
board for the CY3280-BK1 Universal CapSense Controller Kit.
Document Number: 001-53754 Rev. *D
Page 36 of 46
[+] Feedback
CY8C24894
Device Programmers
CY3207ISSP In-System Serial Programmer (ISSP)
All device programmers can be purchased from the Cypress
Online Store.
The CY3207ISSP is a production programmer. It includes
protection circuitry and an industrial case that is more robust than
the MiniProg in a production-programming environment.
CY3210-MiniProg1
The CY3210-MiniProg1 kit allows a user to program PSoC
devices via the MiniProg1 programming unit. The MiniProg is a
small, compact prototyping programmer that connects to the PC
via a provided USB 2.0 cable. The kit includes:
Note: CY3207ISSP needs special software and is not
compatible with PSoC Programmer. The kit includes:
■
CY3207 Programmer Unit
■
PSoC ISSP Software CD
■
MiniProg Programming Unit
■
110 ~ 240 V Power Supply, Euro-Plug Adapter
■
MiniEval Socket Programming and Evaluation Board
■
USB 2.0 Cable
■
28-Pin CY8C29466-24PXI PDIP PSoC Device Sample
■
28-Pin CY8C27443-24PXI PDIP PSoC Device Sample
■
PSoC Designer Software CD
■
Getting Started Guide
■
USB 2.0 Cable
Accessories (Emulation and Programming)
Table 31. Emulation and Programming Accessories
Part #
CY8C24894-24LFXA
Pin Package
56-pin QFN
Flex-Pod Kit[22]
CY3250-24X94QFN
Foot Kit[23]
CY3250-56QFN-FK
Adapter[24]
AS-56-28-01ML-6
Notes
22. Flex-Pod kit includes a practice flex-pod and a practice PCB, in addition to two flex-pods.
23. Foot kit includes surface mount feet that are soldered to the target PCB.
24. Programming adapter converts non-DIP package to DIP footprint. Specific details and ordering information for each of the adapters are found at
http://www.emulation.com.
Document Number: 001-53754 Rev. *D
Page 37 of 46
[+] Feedback
CY8C24894
Ordering Information
XRES Pin
Analog Outputs
Analog Inputs
Digital I/O Pins
Analog Blocks
Digital Blocks
Temperature
Range
SRAM
(Bytes)
Flash
(Bytes)
Package
Ordering
Code
Table 32. CY8C24x94 PSoC Device’s Key Features and Ordering Information
56-pin (8 × 8 mm) QFN,
punched
CY8C24894-24LFXA
16 K 1 K
–40 °C to +85 °C 4
6
49
47
2
Yes
56-pin (8 × 8 mm) QFN,
punched (tape and reel)
CY8C24894-24LFXAT
16 K 1 K
–40 °C to +85 °C 4
6
49
47
2
Yes
Ordering Code Definitions
CY 8 C 24 xxx-SPxx
Package Type:
PX = PDIP Pb-free
SX = SOIC Pb-free
PVX = SSOP Pb-free
LFX/LKX = QFN Pb-free
AX = TQFP Pb-free
BVX = VFBGA Pb-free
Thermal Rating:
A = Automotive –40 °C to +85 °C
C = Commercial
E = Automotive Extended –40 °C to +125 °C
I = Industrial
CPU Speed: 24 MHz
Part Number
Family Code
Technology Code: C = CMOS
Marketing Code: 8 = PSoC
Company ID: CY = Cypress
Document Number: 001-53754 Rev. *D
Page 38 of 46
[+] Feedback
CY8C24894
Reference Information
Acronyms
Table 33 lists the acronyms that are used in this document.
Table 33. Acronyms Used in this Datasheet
Acronym
AC
Description
Acronym
alternating current
MIPS
Description
million instructions per second
ADC
analog-to-digital converter
PCB
printed circuit board
AEC
Automotive Electronics Council
PDIP
plastic dual in-line package
API
application programming interface
PLL
phase-locked loop
CPU
central processing unit
POR
power-on reset
CRC
CT
cyclic redundancy check
PPOR
precision POR
continuous time
PSoC®
Programmable System-on-Chip
DAC
digital-to-analog converter
PWM
pulse-width modulator
DC
direct current or duty cycle
QFN
quad flat no leads
dual-tone multi-frequency
RMS
root mean square
EEPROM
DTMF
electrically erasable programmable read-only
memory
SAR
successive approximation register
EXTCLK
external clock
GPIO
general purpose I/O
SC
SCL / SCLK
serial clock
SDA
serial data
SLIMO
slow IMO
I2C
inter-integrated circuit
ICE
in-circuit emulator
IDE
integrated development environment
SMP
ILO
internal low-speed oscillator
SOIC
IMO
internal main oscillator
I/O
switched capacitor
SPI
switch mode pump
small-outline integrated circuit
serial peripheral interface
input/output
SRAM
static random-access memory
IrDA
Infrared Data Association
SROM
supervisory read-only memory
ISSP
in-system serial programming
TQFP
thin quad flat pack
LCD
liquid crystal display
UART
universal asynchronous receiver
transmitter
LED
light-emitting diode
USB
universal serial bus
LPC
low power comparator
WDT
watchdog timer
LVD
low voltage detect
XRES
external reset
MCU
microcontroller unit
Reference Documents
CY8CPLC20, CY8CLED16P01, CY8C29x66, CY8C27x43, CY8C24x94, CY8C24x23, CY8C24x23A, CY8C22x13, CY8C21x34,
CY8C21x23, CY7C64215, CY7C603xx, CY8CNP1xx, and CYWUSB6953 PSoC® Programmable System-on-Chip Technical
Reference Manual (TRM) (001-14463)
Design Aids – Reading and Writing PSoC® Flash – AN2015 (001-40459)
Understanding Datasheet Jitter Specifications for Cypress Timing Products – AN5054 (001-14503)
Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame (MLF) Packages – available at http://www.amkor.com.
Document Number: 001-53754 Rev. *D
Page 39 of 46
[+] Feedback
CY8C24894
Document Conventions
Units of Measure
The following table lists the units of measure that are used in this document.
Table 34. Units of Measure
Symbol
°C
dB
fF
KB
kHz
kΩ
MHz
μA
μs
μV
mA
ms
mV
Unit of Measure
degree Celsius
decibel
femtofarad
1024 bytes
kilohertz
kilohm
megahertz
microampere
microsecond
microvolt
milliampere
millisecond
millivolt
Symbol
mVPP
nA
ns
nV
Ω
%
pA
pF
ps
rt-Hz
V
W
Unit of Measure
millivolts peak-to-peak
nanoampere
nanosecond
nanovolt
ohm
percent
picoampere
picofarad
picosecond
root hertz
volt
watt
Numeric Conventions
Hexadecimal numbers are represented with all letters in uppercase with an appended lowercase ‘h’ (for example, ‘14h’ or ‘3Ah’).
Hexadecimal numbers may also be represented by a ‘0x’ prefix, the C coding convention. Binary numbers have an appended
lowercase ‘b’ (for example, ‘01010100b’ or ‘01000011b’). Numbers not indicated by an ‘h’, ‘b’, or ‘0x’ are in decimal format.
Glossary
active high
1. A logic signal having its asserted state as the logic 1 state.
2. A logic signal having the logic 1 state as the higher voltage of the two states.
analog blocks
The basic programmable opamp circuits. These are SC (switched capacitor) and CT (continuous time) blocks.
These blocks can be interconnected to provide ADCs, DACs, multi-pole filters, gain stages, and much more.
analog-to-digital
converter (ADC)
A device that changes an analog signal to a digital signal of corresponding magnitude. Typically, an ADC converts
a voltage to a digital number. The digital-to-analog converter (DAC) performs the reverse operation.
Application
programming
interface (API)
A series of software routines that comprise an interface between a computer application and lower level services
and functions (for example, user modules and libraries). APIs serve as building blocks for programmers that create
software applications.
asynchronous
A signal whose data is acknowledged or acted upon immediately, irrespective of any clock signal.
bandgap
reference
A stable voltage reference design that matches the positive temperature coefficient of VT with the negative
temperature coefficient of VBE, to produce a zero temperature coefficient (ideally) reference.
bandwidth
1. The frequency range of a message or information processing system measured in hertz.
2. The width of the spectral region over which an amplifier (or absorber) has substantial gain (or
loss); it is sometimes represented more specifically as, for example, full width at half maximum.
Document Number: 001-53754 Rev. *D
Page 40 of 46
[+] Feedback
CY8C24894
Glossary (continued)
bias
1. A systematic deviation of a value from a reference value.
2. The amount by which the average of a set of values departs from a reference value.
3. The electrical, mechanical, magnetic, or other force (field) applied to a device to establish a reference level to
operate the device.
block
1. A functional unit that performs a single function, such as an oscillator.
2. A functional unit that may be configured to perform one of several functions, such as a digital PSoC block or
an analog PSoC block.
buffer
1. A storage area for data that is used to compensate for a speed difference, when transferring data from one
device to another. Usually refers to an area reserved for I/O operations, into which data is read, or from which
data is written.
2. A portion of memory set aside to store data, often before it is sent to an external device or as it is received
from an external device.
3. An amplifier used to lower the output impedance of a system.
bus
1. A named connection of nets. Bundling nets together in a bus makes it easier to route nets with similar routing
patterns.
2. A set of signals performing a common function and carrying similar data. Typically represented using vector
notation; for example, address[7:0].
3. One or more conductors that serve as a common connection for a group of related devices.
clock
The device that generates a periodic signal with a fixed frequency and duty cycle. A clock is sometimes used to
synchronize different logic blocks.
comparator
An electronic circuit that produces an output voltage or current whenever two input levels simultaneously satisfy
predetermined amplitude requirements.
compiler
A program that translates a high level language, such as C, into machine language.
configuration
space
In PSoC devices, the register space accessed when the XIO bit, in the CPU_F register, is set to
‘1’.
crystal oscillator
An oscillator in which the frequency is controlled by a piezoelectric crystal. Typically a piezoelectric
crystal is less sensitive to ambient temperature than other circuit components.
cyclic redundancy A calculation used to detect errors in data communications, typically performed using a linear feedback shift
check (CRC)
register. Similar calculations may be used for a variety of other purposes such as data compression.
data bus
A bi-directional set of signals used by a computer to convey information from a memory location to the central
processing unit and vice versa. More generally, a set of signals used to convey data between digital functions.
debugger
A hardware and software system that allows you to analyze the operation of the system under development. A
debugger usually allows the developer to step through the firmware one step at a time, set break points, and
analyze memory.
dead band
A period of time when neither of two or more signals are in their active state or in transition.
digital blocks
The 8-bit logic blocks that can act as a counter, timer, serial receiver, serial transmitter, CRC generator,
pseudo-random number generator, or SPI.
digital-to-analog
converter (DAC)
A device that changes a digital signal to an analog signal of corresponding magnitude. The analog-to-digital
converter (ADC) performs the reverse operation.
Document Number: 001-53754 Rev. *D
Page 41 of 46
[+] Feedback
CY8C24894
Glossary (continued)
duty cycle
The relationship of a clock period high time to its low time, expressed as a percent.
emulator
Duplicates (provides an emulation of) the functions of one system with a different system, so that the second
system appears to behave like the first system.
external reset
(XRES)
An active high signal that is driven into the PSoC device. It causes all operation of the CPU and blocks to stop
and return to a pre-defined state.
flash
An electrically programmable and erasable, non-volatile technology that provides you the programmability and
data storage of EPROMs, plus in-system erasability. Non-volatile means that the data is retained when power is
off.
flash block
The smallest amount of flash ROM space that may be programmed at one time and the smallest amount of flash
space that may be protected.
frequency
The number of cycles or events per unit of time, for a periodic function.
gain
The ratio of output current, voltage, or power to input current, voltage, or power, respectively. Gain is usually
expressed in dB.
I2C
A two-wire serial computer bus by Philips Semiconductors (now NXP Semiconductors). It is used to connect
low-speed peripherals in an embedded system. The original system was created in the early 1980s as a battery
control interface, but it was later used as a simple internal bus system for building control electronics. I2C uses
only two bi-directional pins, clock and data, both running at the VDD suppy voltage and pulled high with resistors.
The bus operates up to100 kbits/second in standard mode and 400 kbits/second in fast mode.
ICE
The in-circuit emulator that allows you to test the project in a hardware environment, while viewing the debugging
device activity in a software environment (PSoC Designer).
input/output (I/O) A device that introduces data into or extracts data from a system.
interrupt
A suspension of a process, such as the execution of a computer program, caused by an event external to that
process, and performed in such a way that the process can be resumed.
interrupt service
routine (ISR)
A block of code that normal code execution is diverted to when the CPU receives a hardware interrupt. Many
interrupt sources may each exist with its own priority and individual ISR code block. Each ISR code block ends
with the RETI instruction, returning the device to the point in the program where it left normal program execution.
jitter
1. A misplacement of the timing of a transition from its ideal position. A typical form of corruption that occurs on
serial data streams.
2. The abrupt and unwanted variations of one or more signal characteristics, such as the interval between
successive pulses, the amplitude of successive cycles, or the frequency or phase of successive cycles.
low voltage detect A circuit that senses VDD and provides an interrupt to the system when VDD falls below a selected threshold.
(LVD)
M8C
An 8-bit Harvard-architecture microprocessor. The microprocessor coordinates all activity inside a PSoC by
interfacing to the flash, SRAM, and register space.
master device
A device that controls the timing for data exchanges between two devices. Or when devices are cascaded in
width, the master device is the one that controls the timing for data exchanges between the cascaded devices
and an external interface. The controlled device is called the slave device.
Document Number: 001-53754 Rev. *D
Page 42 of 46
[+] Feedback
CY8C24894
Glossary (continued)
microcontroller
An integrated circuit chip that is designed primarily for control systems and products. In addition to a CPU, a
microcontroller typically includes memory, timing circuits, and I/O circuitry. The reason for this is to permit the
realization of a controller with a minimal quantity of chips, thus achieving maximal possible miniaturization. This
in turn, reduces the volume and the cost of the controller. The microcontroller is normally not used for
general-purpose computation as is a microprocessor.
mixed-signal
The reference to a circuit containing both analog and digital techniques and components.
modulator
A device that imposes a signal on a carrier.
noise
1. A disturbance that affects a signal and that may distort the information carried by the signal.
2. The random variations of one or more characteristics of any entity such as voltage, current, or data.
oscillator
A circuit that may be crystal controlled and is used to generate a clock frequency.
parity
A technique for testing transmitted data. Typically, a binary digit is added to the data to make the sum of all the
digits of the binary data either always even (even parity) or always odd (odd parity).
phase-locked
loop (PLL)
An electronic circuit that controls an oscillator so that it maintains a constant phase angle relative to a reference
signal.
pinouts
The pin number assignment: the relation between the logical inputs and outputs of the PSoC device and their
physical counterparts in the printed circuit board (PCB) package. Pinouts involve pin numbers as a link between
schematic and PCB design (both being computer generated files) and may also involve pin names.
port
A group of pins, usually eight.
power-on reset
(POR)
A circuit that forces the PSoC device to reset when the voltage is below a pre-set level. This is one type of hardware
reset.
PSoC®
Cypress Semiconductor’s PSoC® is a registered trademark and Programmable System-on-Chip™ is a trademark
of Cypress.
PSoC Designer™ The software for Cypress’ Programmable System-on-Chip technology.
pulse width
An output in the form of duty cycle which varies as a function of the applied value.
modulator (PWM)
RAM
An acronym for random access memory. A data-storage device from which data can be read out and new data
can be written in.
register
A storage device with a specific capacity, such as a bit or byte.
reset
A means of bringing a system back to a known state. See hardware reset and software reset.
ROM
An acronym for read only memory. A data-storage device from which data can be read out, but new data cannot
be written in.
serial
1. Pertaining to a process in which all events occur one after the other.
2. Pertaining to the sequential or consecutive occurrence of two or more related activities in a single device or
channel.
settling time
The time it takes for an output signal or value to stabilize after the input has changed from one value to another.
Document Number: 001-53754 Rev. *D
Page 43 of 46
[+] Feedback
CY8C24894
Glossary (continued)
shift register
A memory storage device that sequentially shifts a word either left or right to output a stream of serial data.
slave device
A device that allows another device to control the timing for data exchanges between two devices. Or when
devices are cascaded in width, the slave device is the one that allows another device to control the timing of data
exchanges between the cascaded devices and an external interface. The controlling device is called the master
device.
SRAM
An acronym for static random access memory. A memory device where you can store and retrieve data at a high
rate of speed. The term static is used because, after a value is loaded into an SRAM cell, it remains unchanged
until it is explicitly altered or until power is removed from the device.
SROM
An acronym for supervisory read only memory. The SROM holds code that is used to boot the device, calibrate
circuitry, and perform flash operations. The functions of the SROM may be accessed in normal user code,
operating from flash.
stop bit
A signal following a character or block that prepares the receiving device to receive the next character or block.
synchronous
1. A signal whose data is not acknowledged or acted upon until the next active edge of a clock signal.
2. A system whose operation is synchronized by a clock signal.
tri-state
A function whose output can adopt three states: 0, 1, and Z (high-impedance). The function does not drive any
value in the Z state and, in many respects, may be considered to be disconnected from the rest of the circuit,
allowing another output to drive the same net.
UART
A UART or universal asynchronous receiver-transmitter translates between parallel bits of data and serial bits.
user modules
Pre-built, pre-tested hardware/firmware peripheral functions that take care of managing and configuring the lower
level analog and digital PSoC blocks. User modules also provide high level API (Application Programming
Interface) for the peripheral function.
user space
The bank 0 space of the register map. The registers in this bank are more likely to be modified during normal
program execution and not just during initialization. Registers in bank 1 are most likely to be modified only during
the initialization phase of the program.
VDD
A name for a power net meaning "voltage drain." The most positive power supply signal. Usually 5 V or 3.3 V.
VSS
A name for a power net meaning "voltage source." The most negative power supply signal.
watchdog timer
A timer that must be serviced periodically. If it is not serviced, the CPU resets after a specified period of time.
Document Number: 001-53754 Rev. *D
Page 44 of 46
[+] Feedback
CY8C24894
Document History Page
Document Title: CY8C24894 Automotive PSoC® Programmable System-on-Chip™
Document Number: 001-53754
Revision
ECN
Orig. of
Change
Submission
Date
**
2715097
MASJ
06/08/09
New datasheet.
*A
2782580
BTK
10/09/09
Updated Features section. Updated text of PSoC Functional Overview section.
Updated Getting Started section. Made corrections and minor text edits to
Pinouts section. Changed the name of some sections to improve consistency.
Improved formatting of the register tables. Added clarifying comments to some
electrical specifications. Fixed all AC specifications to conform to a ±4% or ±8%
IMO accuracy. Made other miscellaneous minor text edits. Deleted some
non-applicable or redundant information. Improved and edited content in Development Tool Selection section. Improved the bookmark structure. Changed
FlashENT, VCMOA, the DC POR and LVD specifications, and the DC Analog
Reference specifications according to MASJ directives. Added TXRST, DC24M,
and 3.3 V DC Operational Amplifier specifications.
*B
2822792
BTK/AESA
12/07/09
Added TPRGH, TPRGC, IOL, IOH, F32KU, DCILO, and TPOWERUP electrical specifications. Updated the footnotes of Table 16, “DC Programming Specifications,”
on page 25. Added maximum values and updated typical values for TERASEB
and TWRITE electrical specifications. Replaced TRAMP electrical specification
with SRPOWERUP electrical specification. Added “Contents” on page 2.
*C
2888007
NJF
03/30/10
Updated Cypress website links.
Removed reference to PSoC Designer 4.4 in PSoC Designer Software
Subsystems
Updated The Analog System.
Added TBAKETEMP and TBAKETIME parameters in Absolute Maximum Ratings.
Updated AC Chip-Level Specifications. Updated Packaging Information.
Removed Third Party Tools and Build a PSoC Emulator into your Board.
Updated links in Sales, Solutions, and Legal Information.
*D
3272922
BTK/NJF
06/02/11
Updated Figure 8 on page 33 to improve clarity.
Updated wording, formatting, and notes of the AC Digital Block Specifications
table to improve clarity.
Added VDDP, VDDLV, and VDDHV electrical specifications to give more information for programming the device.
Updated Solder Reflow Specifications to give more clarity.
Updated the jitter specifications.
Updated PSoC Device Characteristics table.
Updated the F32KU electrical specification.
Updated note for RPD electrical specification.
Updated note for the TSTG electrical specification to add more clarity.
Added Tape and Reel Specifications section.
Added CL electrical specification.
Updated DC Analog Reference Specifications.
Changed “NC” pins on the device to “DNC” pins.
Corrected information about the exposed pad to clarify that it is not internally
connected.
Document Number: 001-53754 Rev. *D
Description of Change
Page 45 of 46
[+] Feedback
CY8C24894
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
PSoC
Touch Sensing
USB Controllers
Wireless/RF
cypress.com/go/memory
cypress.com/go/image
cypress.com/go/psoc
cypress.com/go/touch
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2009-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-53754 Rev. *D
Revised June 2, 2011
Page 46 of 46
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback