Issue No. : PC-04-006 Date of issue : March 2, 2004 Classification : New Messrs. Digi-Key Product Description : Balun Product Part Number Applications : EHF4BE5250 : Cellular phone Term of Validity For other applications, contact the undersigned in advance. : Five years from the date of issue. Delivery Specification Receipt Used Column MATSUSHITA ELECTRONIC COMPONENTS CO., LTD. MODULE DEVICE COMPANY MODULE BUSINESS UNIT 992-1 AIBA OHNO-CHO IBI-GUN GIHU PREF 501-0598 JAPAN TEL +81-585-36-2345 FAX +81-585-36-2353 Communication Module Business Group Prepared by : H. Ito Authorized by : M. Mizuno [Manufacturing section] (Name) Final Production Plant MATSUSHITA ELECTRONIC COMPONENTS CO., LTD. (Address) 992-1 AIBA OHNO-CHO IBI-GUN GIHU PREF 501-0598 JAPAN Final Inspection Plant The same as above [Shape, appearance, dimension] Unit: mm <Top view> <Bottom and side view> GND (5) OUT2 (4) (1) IN (2) GND (3) OUT1 1.6+/-0.1 (4) (5) (6) (3) (2) (1) 0.65+/-0.1 0.8+/-0.1 NU (6) Sn Ni Ceramic substrate Ag-Pd Weight of the individual component: 3mg Note 1) “typ” is used where no dimensional tolerance applies. Item Appearance/ construction Description Product surface shall be covered with a protective film, which does not easily separate nor present noticeable unevenness, scratches, pinholes, color changes etc. Terminals shall ensure practically acceptable quality Substrate shall be as shown in the drawing with no excessive chippings, scratches, burrs, or cracks. Marking Remarks Shall be legible in black (with printing paste) marked side for pin 1 Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Appearance Drawing No. 151-EHF-4BE5250 9-1 [Absolute maximum ratings] No. Item Symbol Rating 1 Maximum input power Pmax 100 2 Operating temperature Topr Unit Remarks mW DC bias must be 0V -30…+85 degC 3 Storage temperature Tstg -40…+85 Note: This component cannot apply a DC Bias. [Electrical characteristics] No. Item degC T=-30…+85degC Specification Test Unit Circuit Min. Typ. Max. Fig-2 5150 - - 5350 1.2 MHz dB 1 2 Frequency Insertion loss (Back to back) 3 Unbalance impedance - - 50 - ohm 4 Balance impedance - - 100 - ohm 5 6 Unbalance port VSWR Amplitude balance Fig-1 Fig-1 -1.5 - 2.0 1.5 dB 7 Phase balance Fig-1 165 180 195 deg [Internal circuitry] (1)IN (5)GND (2)GND (2)GND (4)OUT2 (3)OUT1 [Measuring circuit] < Phase balance measurement > •Phase1 A=IN, B=OUT, C=Terminal resistor (50 ohm) •Phase2 A=IN, C=OUT, B=Terminal resistor (50 ohm) •Phase balance Phase balance=Phase1-Phase2 < Insertion loss measurement > Assuming the loss as “Loss” when D=IN, E=OUT Insertion loss for a device is “Loss”/2 NETWORK ANALYZER S-PARAMETER TEST SET IN C FIG.1 GND OUT GND GND FIG.2 E A B D GND GND Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Specification and measurement Drawing No. 151-EHF-4BE5250 9-2 [Terminal dimensions] Unit: mm <Bottom> 0.2+/-0.1 0.4+/-0.1 0.2+/-0.1 Pin No. (4) (5) (6) Bottom View (3) 0.25+/-0.1 0.3+/-0.1 (2) (1) 0.55+/-0.1 0.55+/-0.1 (6) NU (5) GND 0.30 0.55 1.4 0.55 [Recommended PCB pad dimensions] Unit: mm (4) OUT2 Product Top View (1) IN 0.3 (2) GND 0.3 0.25 PCB Pad (3) OUT1 0.3 0.3 1.45 Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Terminals/Recommended lands Drawing No. 151-EHF-4BE5250 9-3 [Quality characteristics] Test condition Test item Temperature cycling -40…+85degC, Each 30 min., 200cy High temperature +85degC, 1000h High-temperature high-humidity storage +85degC, 85%RH, 1000h Low temperature -40degC, 1000h Vibration 0.35mm 10-55Hz, 50m/s2 55-500Hz Judgment criteria No abnormality shall be observed in appearance or electrical characteristics 10-500-10Hz/11min.,in each direction of XYZ, 2h Shock (Drop) 1.8m, 6 facesx3cy(with 100g Dummy Load) Soldering heat resistance Reflow: 260degC peak, 3 times Electro static discharge 200pF, 0 ohm, +/-200V, Each 3 times Solder ability Solder bath: 230+/-3degC, 3 sec. Board warping Over 95% of the terminal surface shall be covered with solder FR-4(t=1.0mm), 45+/-2mm span, 5+/-1sec. 1mm step, 2mm 45mm 45mm t=1.0mm 2mm There should not be any cracks in the component or solder joints, no abnormality in electrical characteristics. Terminal removal Solder a component on a PC board using the recommended condition shown below and then press the component sideways at 1mm/sec. Destruction limit 4.9N or greater. Seating plane co-planarity Within 0.1mm Temperature < Recommended soldering condition > Diagram1 Shown below is a recommended reflow soldering condition degC 260 230 200 175 150 135 60~120 sec. 60~70 sec. Time Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Quality Characteristics Drawing No. 151-EHF-4BE5250 9-4 [Cautions for use] (1) Operating a product over the maximum rating for even a moment may result in a product failure or breakage. Never use a product in such a condition that it may cause a safety problem. (2) Opening or short-circuiting the product terminals or inserting a product in the reverse orientation while power is being supplied may cause a breakage. Always avoid such circumstances. (3) Operations in a corrosive gas atmosphere or improper environments such as hightemperature, high-humidity or dewy conditions may lead to product performance deterioration, a breakage, a change in appearance etc. Please avoid such conditions, as they are unsafe. (4) Always ground the soldering iron or soldering bath used for assembly operation to avoid any excessive voltage applied to a product. (5) After soldering with solder bridges, incomplete soldering or in the reverse orientation, supplying power may result in a product breakage. Please confirm the soldered condition before supplying power to the product. (6) Excessive stress on the terminals may cause a contact failure or performance deterioration. Please use caution. (7) Please provide a fail-safe provision in the product you design by taking any failure of our product into consideration. (8) This product does not include a DC-cutting device. Application of a DC voltage between the Balance port and the Unbalance port may cause product deterioration or breakage. * If any question arises about the safety of this product, please contact us immediately with a request for an engineering examination. [Remarks] *1: All of the materials used in this product are those listed as the existing chemical substances based on the “Law for examination and regulation of manufacture of chemical substances” *2: The production process of this product does not use any ozone-depleting chemicals (OZC) regulated by the Montreal Protocol. *3: Validity of this specification is 5 years from the date of issue, but the validity is considered on going unless any changes are made. Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Cautions Drawing No. 151-EHF-4BE5250 9-5 [Packaging materials] 1. Materials 1) Embossed carrier tape (Refer to the attachment) 2) Top tape: Anti-static 3) Packaging box (Refer to the attachment) 4) Packaging tape, carrier-securing adhesive tape 2. Specification No. Item Remarks Condition 1 Reel outer diameter Refer to the attachment 2 Reel inner diameter Refer to the attachment 3 Reel inner width Refer to the attachment 4 Quantity in a reel 4000 pieces/reel 5 Taping direction Tape unreeling direction (with markings facing up) 6 Top tape attachment position Top tape 8.0+/-0.2mm 5.5mm < Top tape attachment area > Embossed tape Top tape edge must stay inside the sprocket holes of the embossed carrier (Sprocket holes shall not be covered) 7 Label attachment Tape unreeling direction position Label Tape breaks force. Min. 10N Top cover tape strength. Min. 10N Tape peel force. 0.1…1.0N Tape peel angle. 165…180degree Reel weight. Max 1500g Indicated Item Pat No., Lot No. Quantity, Maker Country Leader part 8 Tape leader part and tape ending part Ending part Product-loaded part Embossed carrier 200~220mm (Product-unloaded part) 100~150mm, 25~38 pieces worth, (Product-unloaded part) 9 Missing products No missing products shall be allowed 10 Packaged quantity in a box 21 reels/box (Max) Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito Top tape 300~ 400mm 84000 pieces/box(Max) EHF4BE5250 Packaging specification 1 Drawing No. 151-EHF-4BE5250 9-6 1. Method 1) Load products in each cavity of an embossed carrier tape, in the correct orientation, by leaving the product-unloaded part shown in Item No. 8(P9-6) of the packaging specification. 2) Heat-seal a top tape in good alignment on the carrier tape. 3) After 4000 pieces are loaded and reeled, provide a product-unloaded part at the tape-leader portion. Secure the tip of the carrier tape with a piece of adhesive tape. 4) Stack the reels (21 reels max.) and enclose them in a packaging box. Close the flaps with a piece of adhesive tape. 5) Provide markings on the packaging box. < Items to be indicated > 1. Part No. 2. Quantity 3. Lot No. 4. Manufacturer name 5. Country of origin Marking on the packaging box Packaging box shape varies with the number of reels enclosed Reel label Number of stacking, 21 reels max. * Insert cushion material in the empty spaces to secure reels Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Packaging specification 2 Drawing No. 151-EHF-4BE5250 9-7 [Embossed tape dimensions] Unit: mm 2+/-0.05 +0.1 0.25+/-0.05 R0.3 max 1.8+/-0.1 (2.75) 8.0+/-0.2 d1.5 -0 3.5+/-0.05 1.75+/-0.1 4+/-0.1 5deg max 4.0+/-0.1 2.0+/-0.05 0.7+/-0.1 5deg max R0.3 max 0.3 1.0+/-0.1 <Remarks> (1) Unspecified corner radius shall be 0.3mm max. (2) Cumulative pitch error of sprocket holes shall be +/-0.2mm for 10 pitches. Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Packaging specification 3 Drawing No. 151-EHF-4BE5250 9-8 ƒ Ó -3 0 18 0 A ƒÓ R85 ƒÓ 3 [Reel dimensions] Unit: mm (1) This reel conforms to EIAJ-RRM-08B based on EIAJ standard (2) Material: PS (Polystyrene) 44 Center area N MI } 0.2 2 18 .0 2 2-R1 2 R10 .5 } 2 0.2 W2 N ƒ Ó 60+1 0 W1 10 Ó 13 ƒ ƒÓ MIN 18.0 3} 0.4 5 R0. Ó 3 ƒ B } 0.2 120‹ 1 2-R MI N .0 18 ‹ 120 } 0 .2 H 3 B 3 B Label 105...50 0.2 0.4 0.6 0.8 0.8 0.6 H 0.4 0.2 5 4 Scale Rim , Hub Rim A 3 180 0 -3 Hub N 60 +1 0 Inner width , Outer width Tape width 8 Inner width W1 Outer width W2 9+/-0.3 11+/-1.0 Number 105 110 Balun Delivery Specification Enact. Date Enfo. Date March 2, 2004 March 2, 2004 P.S.M Approval Check Plan ----- M. Mizuno M. Mizuno H. Ito EHF4BE5250 Packaging specification 4 Drawing No. 151-EHF-4BE5250 9-9