EL5162, EL5163, EL5262, EL5263, EL5362 ® Data Sheet September 8, 2005 500MHz Low Power Current Feedback Amplifiers with Enable The EL5162, EL5163, EL5262, EL5263, and EL5362 are current feedback amplifiers with a bandwidth of 500MHz. This makes these amplifiers ideal for today’s high speed video and monitor applications. With a supply current of just 1.5mA and the ability to run from a single supply voltage from 5V to 12V, these amplifiers are also ideal for handheld, portable or battery-powered equipment. The EL5162 also incorporates an enable and disable function to reduce the supply current to 100µA typical per amplifier. Allowing the CE pin to float or applying a low logic level will enable the amplifier. The EL5162 is available in 6-pin SOT-23 and 8-pin SO packages, the EL5163 in 5-pin SOT-23 and SC-70 packages, the EL5262 in the 10-pin MSOP package, the EL5263 in 8-pin MSOP and SO packages, and the EL5362 in 16-pin SO (0.150”) and QSOP packages. All operate over the industrial temperature range of -40°C to +85°C. FN7388.7 Features • 500MHz -3dB bandwidth • 4000V/µs slew rate • 1.5mA supply current • Single and dual supply operation, from 5V to 12V supply span • Fast enable/disable (EL5162, EL5262 & EL5362 only) • Available in SOT-23 packages • Pb-Free plus anneal available (RoHS compliant) • High speed, 1.4GHz product available (EL5167 & EL5167) • High speed, 4mA, 630MHz product available (EL5164 & EL5165) Applications • Battery-powered equipment • Handheld, portable devices • Video amplifiers • Cable drivers • RGB amplifiers • Test equipment • Instrumentation • Current to voltage converters 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2005. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. EL5162, EL5163, EL5262, EL5263, EL5362 Ordering Information Ordering Information (Continued) TAPE & REEL PKG. DWG. # 8-Pin SO (Pb-Free) 13” MDP0027 EL5263IY 8-Pin MSOP - MDP0043 EL5263IY-T7 8-Pin MSOP 7” MDP0043 EL5263IY-T13 8-Pin MSOP 13” MDP0043 EL5362IS 16-Pin SO (0.150”) - MDP0027 MDP0027 EL5362IS-T7 16-Pin SO (0.150”) 7” MDP0027 7” (3K pcs) MDP0038 EL5362IS-T13 13” MDP0027 6-Pin SOT-23 7” (250 pcs) MDP0038 16-Pin SO (0.150”) EL5162IWZ-T7 (See Note) 6-Pin SOT-23 (Pb-Free) 7” (3K pcs) MDP0038 EL5362ISZ (See Note) 16-Pin SO (0.150”) (Pb-Free) - MDP0027 EL5162IWZ-T7A (See Note) 6-Pin SOT-23 (Pb-Free) 7” (250 pcs) MDP0038 EL5362ISZ-T7 (See Note) 7” MDP0027 EL5163IW-T7 5-Pin SOT-23 7” (3K pcs) MDP0038 16-Pin SO (0.150”) (Pb-Free) EL5163IW-T7A 5-Pin SOT-23 7” (250 pcs) MDP0038 EL5362ISZ-T13 (See Note) 13” MDP0027 EL5163IWZ-T7 (See Note) 5-Pin SOT-23 (Pb-Free) 7” (3K pcs) MDP0038 16-Pin SO (0.150”) (Pb-Free) EL5362IU 16-Pin QSOP - MDP0040 EL5163IWZ-T7A (See Note) 5-Pin SOT-23 (Pb-Free) 7” (250 pcs) MDP0038 EL5362IU-T7 16-Pin QSOP 7” MDP0040 EL5163IC-T7 5-Pin SC-70 7” (3K pcs) P5.049 EL5362IU-T13 16-Pin QSOP 13” MDP0040 EL5163IC-T7A 5-Pin SC-70 7” (250 pcs) P5.049 EL5362IUZ (See Note) 16-Pin QSOP (Pb-Free) - MDP0040 EL5163ICZ-T7 (See Note) 5-Pin SC-70 (Pb-Free) 7” (3K pcs) P5.049 EL5362IUZ-T7 (See Note) 16-Pin QSOP (Pb-Free) 7” MDP0040 EL5163ICZ-T7A (See Note) 5-Pin SC-70 (Pb-Free) 7” (250 pcs) P5.049 EL5362IUZ-T13 (See Note) 16-Pin QSOP (Pb-Free) 13” MDP0040 EL5262IY 10-Pin MSOP - MDP0043 EL5262IY-T7 10-Pin MSOP 7” MDP0043 EL5262IY-T13 10-Pin MSOP 13” MDP0043 EL5262IYZ (See Note) 10-Pin MSOP (Pb-Free) - MDP0043 EL5262IYZ-T7 (See Note) 10-Pin MSOP (Pb-Free) 7” MDP0043 EL5262IYZ-T13 (See Note) 10-Pin MSOP (Pb-Free) 13” MDP0043 EL5263IS 8-Pin SO - MDP0027 EL5263IS-T7 8-Pin SO 7” MDP0027 EL5263IS-T13 8-Pin SO 13” MDP0027 EL5263ISZ (See Note) 8-Pin SO (Pb-Free) - MDP0027 EL5263ISZ-T7 (See Note) 8-Pin SO (Pb-Free) 7” MDP0027 PACKAGE TAPE & REEL PKG. DWG. # EL5162IS 8-Pin SO - MDP0027 EL5162IS-T7 8-Pin SO 7” MDP0027 EL5162IS-T13 8-Pin SO 13” MDP0027 EL5162ISZ (See Note) 8-Pin SO (Pb-Free) - MDP0027 EL5162ISZ-T7 (See Note) 8-Pin SO (Pb-Free) 7” MDP0027 EL5162ISZ-T13 (See Note) 8-Pin SO (Pb-Free) 13” EL5162IW-T7 6-Pin SOT-23 EL5162IW-T7A PART NUMBER 2 PART NUMBER EL5263ISZ-T13 (See Note) PACKAGE NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Pinouts NC 1 IN- 2 + IN+ 3 VS- 4 8 CE OUT 1 7 VS+ VS- 2 6 OUT IN+ 3 OUT 1 IN+ 3 VS- 4 CE 5 + - 6 VS+ OUT 1 5 CE VS- 2 4 IN- IN+ 3 5 VS+ + - 4 IN- 5 NC EL5263 (8-PIN SO, MSOP) TOP VIEW EL5262 (10-PIN MSOP) TOP VIEW IN- 2 EL5163 (5-PIN SOT-23, SC-70) TOP VIEW EL5162 (6-PIN SOT-23) TOP VIEW EL5162 (8-PIN SO) TOP VIEW 10 VS+ + + OUT1 1 9 OUT IN- 2 8 IN- IN+ 3 7 IN+ 6 CE VS- 4 8 VS+ 7 OUT2 + + 6 IN5 IN+ EL5362 (16-PIN SO (0.150”), QSOP) TOP VIEW INA+ 1 CEA 2 16 INA+ VS- 3 CEB 4 14 VS+ + - INB+ 5 INC+ 8 3 13 OUTB 12 INB- NC 6 CEC 7 15 OUTA 11 NC + - 10 OUTC 9 INC- FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Absolute Maximum Ratings (TA = 25°C) Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . 13.2V Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Slewrate of VS+ to VS-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs Maximum Voltage between IN+ and IN-, disabled. . . . . . . . . . ±1.5V Current into IN+, IN-, CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5mA Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . .VS- - 0.5V to VS+ +0.5V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 400Ω for AV = 2, RL = 150Ω, TA = 25°C unless otherwise specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT AC PERFORMANCE BW -3dB Bandwidth BW1 0.1dB Bandwidth SR Slew Rate tS 0.1% Settling Time eN AV = +1, RL = 500Ω, RF = 598Ω 500 MHz AV = +2, RL = 150Ω, RF = 422Ω 233 MHz 30 MHz VO = -2.5V to +2.5V, AV = +2, RL = 100Ω (EL5262, EL5263, EL5362) 2000 2500 4000 V/µs VO = -2.5V to +2.5V, AV = +2, RL = 100Ω (EL5162, EL5163) 2800 4000 6000 V/µs VOUT = -2.5V to +2.5V, AV = +1 25 ns Input Voltage Noise 3 nV/√Hz iN- IN- Input Current Noise 10 pA/√Hz iN+ IN+ Input Current Noise 6.5 pA/√Hz dG Differential Gain Error (Note 1) AV = +2 0.05 % dP Differential Phase Error (Note 1) AV = +2 0.15 ° DC PERFORMANCE VOS Offset Voltage TCVOS Input Offset Voltage Temperature Coefficient ROL Transimpedance -5 Measured from TMIN to TMAX 1.5 +5 mV 6 µV/°C 500 1000 kΩ V INPUT CHARACTERISTICS CMIR Common Mode Input Range Guaranteed by CMRR test ±3 ±3.3 CMRR Common Mode Rejection Ratio VIN = ±3V 50 62 75 dB -ICMR - Input Current Common Mode Rejection -1 0.22 +1 µA/V +IIN + Input Current -8 0.5 +8 µA -IIN - Input Current -10 2 +10 µA RIN Input Resistance 0.8 1.6 3 MΩ CIN Input Capacitance 1 pF OUTPUT CHARACTERISTICS VO IOUT Output Voltage Swing Output Current 4 RL = 150Ω to GND ±3.35 ±3.6 ±3.75 V RL = 1kΩ to GND ±3.75 ±3.9 ±4.15 V RL = 10Ω to GND 60 100 mA FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 400Ω for AV = 2, RL = 150Ω, TA = 25°C unless otherwise specified. (Continued) DESCRIPTION CONDITIONS MIN TYP MAX UNIT SUPPLY ISON Supply Current - Enabled, per Amplifier No load, VIN = 0V 1.3 1.5 1.7 mA ISOFF- Supply Current - Disabled, per Amplifier No load, VIN = 0V -25 -14 0 µA 0 10 +25 µA ISOFF+ PSRR Power Supply Rejection Ratio DC, VS = ±4.75V to ±5.25V 65 76 -IPSR - Input Current Power Supply Rejection DC, VS = ±4.75V to ±5.25V -0.5 0.1 dB +0.5 µA/V ENABLE (EL5162, EL5262, EL5362 ONLY) tEN Enable Time 380 ns tDIS Disable Time 800 ns IIHCE CE Pin Input High Current CE = VS+ 1 5 25 µA IILCE CE Pin Input Low Current CE = (VS+) -5V -1 0 +1 µA VIHCE CE Input High Voltage for Power-down VILCE CE Input Low Voltage for Power-down VS+ - 1 V VS+ - 3 V NOTE: 1. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz 5 FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Typical Performance Curves NORMALIZED GAIN (dB) +2 +1 +4 VCC = +5V VEE = -5V RL = 500Ω RF = 598Ω +3 NORMALIZED GAIN (dB) +4 +3 0 -1 -2 -3 -4 +2 VCC = +5V VEE = -5V RF = 375Ω +1 0 -1 -2 -3 -4 -5 -5 -6 100K 1M 10M 100M -6 100K 1G 1M FREQENCY (Hz) +2 +3 +1 +2 0 +1 -1 -2 -3 -4 -5 -6 -7 VCC = +5V VEE = -5V AV = +10 RL = 150Ω RF = 375Ω -8 100K 0 -1 -2 -3 -4 -5 -6 1M 10M 100M VCC = +5V VEE = -5V RL = 150Ω RF = 422Ω -7 100K 1G 1M +3 +5 +2 +4 +1 +3 0 -1 -2 -3 -6 VCC = +5V VEE = -5V RL = 150Ω RF = 422Ω -7 100K 100M AV = +1 RL = 150Ω RF = 698Ω +2 ±6V +1 0 -1 VCC, VEE = ±5V ±4V -2 ±3V ±2.5V -3 -4 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 5. FREQUENCY RESPONSE FOR AV = +4 6 1G FIGURE 4. FREQUENCY RESPONSE FOR AV = +2 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) FIGURE 3. FREQUENCY RESPONSE FOR AV = +10 -5 10M FREQUENCY (Hz) FREQUENCY (Hz) -4 1G FIGURE 2. FREQUENCY RESPONSE FOR AV = +4.6 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) FIGURE 1. FREQUENCY RESPONSE FOR AV = +1 10M 100M FREQUENCY (Hz) -5 100K 1M 10M 100M 500M FREQUENCY (Hz) FIGURE 6. FREQUENCY RESPONSE FOR VARIOUS VCC, VEE FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Typical Performance Curves (Continued) VCC = +5V VEE = -5V AV = +2 VCC = +5V VEE = -5V AV = +2 RL = 150Ω 10 1V/DIV 1 INPUT RISE TIME 1.028ns OUTPUT RISE TIME 2.218ns 2V/DIV 0.1 10K 100K 1M 10M 100M 4ns/DIV FREQUENCY (Hz) FIGURE 7. CLOSED LOOP OUTPUT IMPEDANCE 1V/DIV INPUT FALL TIME 1.036ns OUTPUT FALL TIME 2.21ns FIGURE 8. EL5262 OUTPUT RISE TIME VCC = +5V VEE = -5V AV = +2 RL = 150Ω CH 1 2V/DIV CH 2 CH 1 = 5V CH 2 = 200mV M = 100ns 100ns/DIV 4ns/DIV FIGURE 9. EL5262 OUTPUT FALL TIME FIGURE 10. TURN ON TIME 0 VCC = +5V -10 V = -5V EE -20 AV = +2 RL = 150Ω -30 CH 1 = 5V CH 2 = 200mV M = 100ns CH 1 PSRR (dB) OUTPUT IMPEDANCE (Ω) 100 -40 -50 -60 -70 CH 2 -80 -90 -100 100ns/DIV FIGURE 11. TURN OFF TIME 7 100 1K 10K 100K 1M 10M 100M FREQUENCY (Hz) FIGURE 12. PSRR (VCC) FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Typical Performance Curves (Continued) 0 1.4 POWER DISSIPATION (W) PSRR (dB) VCC = +5V -10 VEE = -5V -20 AV = +2 RL = 150Ω -30 -40 -50 -60 -70 -80 -90 -100 1.2 1.250W 1K 10K 100K 1M 10M 0.8 909mW 0.6 SO8 θJA=110°C/W 0.4 0.2 100M 0 25 FREQUENCY (Hz) 1 893mW QSOP16 θJA=112°C/W 0.4 0.2 0 0.4 0.35 SOT23-5/6 θJA=230°C/W 0.3 0.25 0.2 0.15 0.1 0.05 0 25 75 85 100 50 125 0 150 0 25 1 125 150 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0.9 POWER DISSIPATION (W) POWER DISSIPATION (W) 0.9 870mW 0.8 MSOP8/10 θJA=115°C/W 0.7 75 85 100 FIGURE 16. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0.6 50 AMBIENT TEMPERATURE (°C) FIGURE 15. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 0.5 0.4 0.3 0.2 909mW 0.8 SO16 (0.150”) θJA=110°C/W 0.7 0.6 625mW 0.5 0.4 SO8 θJA=160°C/W 0.3 0.2 0.1 0.1 0 150 0.5 0.45 435mW AMBIENT TEMPERATURE (°C) 1 125 JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD POWER DISSIPATION (W) POWER DISSIPATION (W) 1.2 0.6 75 85 100 FIGURE 14. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0.8 50 AMBIENT TEMPERATURE (°C) FIGURE 13. PSRR (VEE) 1.4 SO16 (0.150”) θJA=80°C/W 1 0 100 JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0 25 75 85 50 100 125 AMBIENT TEMPERATURE (°C) FIGURE 17. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 8 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 18. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FN7388.7 September 8, 2005 EL5162, EL5163, EL5262, EL5263, EL5362 Typical Performance Curves JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 0.45 1 POWER DISSIPATION (W) POWER DISSIPATION (W) 1.2 (Continued) 0.8 633mW QSOP16 θJA=158°C/W 0.6 0.4 0.2 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) POWER DISSIPATION (W) 391mW 0.4 0.35 0.3 SOT23-5/6 θJA=256°C/W 0.25 0.2 0.15 0.1 0.05 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 19. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 0.6 JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 486mW 0.5 MSOP8/10 θJA=206°C/W 0.4 0.3 0.2 0.1 0 0 25 75 85 50 100 125 AMBIENT TEMPERATURE (°C) FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 9 FN7388.7 September 8, 2005