Document 634-1 Shielded Power Inductors – EPL3015 • Low profile shielded power inductors, 3 × 3 × 1.5 mm • Extremely low DCR and high SRF ratings • Isat ratings up to 2.4 A • More values will be available soon Designer’s Kit C405 contains 5 each of all values Core material Ferrite Terminations RoHS compliant tin-silver-copper over tin over nickel over silver. Other terminations available at additional cost. Weight 45 – 51 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 2000/7″reel; 7500/13″ reel Plastic tape: 8 mm wide, 0.2 mm thick, 4 mm pocket spacing, 1.65 mm pocket depth PCB washing Only pure water or alcohol recommended Part number1 Inductance2 ±20% (µH) EPL3015-901ML_ 0.90 EPL3015-122ML_ 1.2 EPL3015-152ML_ 1.5 EPL3015-222ML_ 2.2 EPL3015-332ML_ 3.3 EPL3015-472ML_ 4.7 EPL3015-682ML_ 6.8 EPL3015-103ML_10 EPL3015-153ML_15 EPL3015-223ML_22 EPL3015-333ML_33 DCR (Ohms)3 nom max 0.048 0.055 0.054 0.062 0.062 0.072 0.082 0.094 0.108 0.124 0.145 0.167 0.194 0.223 0.301 0.346 0.435 0.500 0.576 0.662 0.860 0.989 Isat (A)5 typ4 (MHz) 10% drop 20% drop 30% drop SRF 130 105 100 75 55 50 38 32 26 20 15.5 1.201.902.40 1.001.602.05 0.901.401.90 0.751.201.60 0.651.101.40 0.550.901.20 0.450.751.00 0.350.590.81 0.240.430.62 0.210.360.51 0.190.320.45 Irms (A)6 20°C rise 40°C rise 1.85 2.45 1.80 2.40 1.55 2.05 1.50 2.00 1.20 1.70 1.00 1.40 0.90 1.20 0.76 1.00 0.61 0.82 0.56 0.74 0.44 0.59 1. When ordering, please specify packaging code: EPL3015-333MLC Packaging:C=7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B=Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D =13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 4395A network analyzer or equivalent. 5. DC current at which the inductance drops the specified amount from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 634-1 Revised 09/17/09 Document 634-2 Shielded Power Inductors – EPL3015 Series Typical L vs Frequency Typical L vs Current 100 33 µH 10 µH 6.8 µH 4.7 µH 10 2.2 µH 0.9 µH 1 33 µH Inductance (µH) Inductance (µH) 100 10 10 µH 6.8 µH 4.7 µH 2.2 µH 1 0.9 µH 0.1 1 0.1 10 100 0.1 0.01 1 0.1 Frequency (MHz) Current Derating Part Marking 120 110 2nd significant digit 0.118 ±0.008 3,0 ±0,2 100 1st significant digit Multiplier 90 80 0.118 ±0.008 3,0 ±0,2 70 60 0.061 max 1,55 50 Recommended Land Pattern 40 25°C Percent of rated Irms 10 Current (A) 30 Start 0.082 2,08 Finish 20 10 0 -40 -20 0 20 40 60 80 100 0.126 3,2 120 140 Ambient temperature (°C) Part Marking (Parts manufactured prior to Sept. 15, 2009 may not be marked.) Part number EPL3015-901 EPL3015-122 EPL3015-152 EPL3015-222 EPL3015-332 EPL3015-472 EPL3015-682 EPL3015-103 EPL3015-153 EPL3015-223 EPL3015-333 Value 0.90 µH 1.2 µH 1.5 µH 2.2 µH 3.3 µH 4.7 µH 6.8 µH 10 µH 15 µH 22 µH 33 µH 1st digit White Brown Brown Red Orange Yellow Blue Brown Brown Red Orange 2nd digit Black Red Green Red Orange Violet Gray Black Green Red Orange Multiplier Brown Red Red Red Red Red Red Orange Orange Orange Orange 0.043 min 1,1 Dimensions are in 0.044 1,12 inches mm Small surface blemishes are not unusual and do not adversely affect performance. Wire may be visible inside the voids. Acceptable void sizes: Top: 0.01 in / 0,254 mm × 0.01 in / 0,254 mm Sides: 0.02 in / 0,5 mm × 0.047 in / 1,2 mm Note: All marked parts have three dots. Black dot, used only on -901 and ‑103 as second significant digit, may be very difficult to see. Document 634-2 Revised 09/17/09