www.fairchildsemi.com FAN8045G3 4-CH Motor Driver (5 Input & 4 Output) Features Description • • • • • • • The FAN8045G3 is a monolithic integrated circuit suitable for a 4-CH motor driver which drives a tracking actuator, a focus actuator, a sled motor, a spindle motor, and a tray motor of the CDP/CAR-CD/DVDP systems. 4-CH Balanced Transformerless (BTL) Driver Optional Input (CH4,5) For Output CH4 Operating Supply Voltage : 4.5 V ~ 14V Built-in Thermal Shut Down Circuit (TSD) Built-in Channel Mute Circuit Built-in 1-OP AMP TSD Monitering Function Typical Application • • • • Compact Disk Player Video Compact Disk Player Car Compact Disk Player Digital Video Disk Player 28-SSOPH-375SG2 Ordering Information Device FAN8045G3 FAN8045G3X note1 FAN8045G3_NL note2 FAN8045G3X_NL Package Operating Temp. 28-SSOPH-375-SG2 -35°C ~ +85°C 28-SSOPH-375-SG2 -35°C ~ +85°C 28-SSOPH-375-SG2 -35°C ~ +85°C 28-SSOPH-375-SG2 -35°C ~ +85°C Notes: 1. X : Tape&Reel 2. NL : Lead free Rev. 1.0.1 ©2003 Fairchild Semiconductor Corporation FAN8045G3 Pin Assignments SW45 MUTE3 28 27 IN5 REF2 IN4 IN3 SVcc 26 25 24 23 22 FIN PVcc2 MUTE4 GND DO3- DO3+ DO4- DO4+ 21 20 19 18 17 16 15 FAN8045G3 2 1 2 3 4 5 REF1 IN1 IN2 OPIN+ OPIN- 6 OPOUT 7 GND FIN 8 9 10 11 12 13 14 PVcc1 MUTE 12 GND DO2- DO2+ DO1- DO1+ FAN8045G3 Pin Definitions Pin Number Pin Name I/O Pin Function Description 1 REF1 I Bias Voltage Input 2 IN1 I CH1 Input 3 IN2 I CH2 Input 4 OPIN+ I Nomal OP-AMP Input(+) 5 OPIN- I Nomal OP-AMP Input(-) 6 OPOUT O Nomal OP-AMP Output 7 GND - Signal Ground 8 PVcc1 - Power Vcc (CH1,CH2) 9 MUTE12 I Mute 1,2 10 GND - Power GND(CH1,CH2) 11 DO2- O CH2 Drive Output (-) 12 DO2+ O CH2 Drive Output (+) 13 DO1- O CH1 Drive Output (-) 14 DO1+ O CH1 Drive Output (+) 15 DO4+ O CH4 Drive Output (+) 16 DO4- O CH4 Drive Output (-) 17 DO3+ O CH3 Drive Output (+) 18 DO3- O CH3 Drive Output (-) 19 GND - Power GND(CH3,CH4) 20 MUTE4 I Mute 4 21 PVcc2 - Power Vcc (CH3,CH4) 22 SVcc - Signal Vcc 23 IN3 I CH3 Input 24 IN4 I CH4 Input 25 REF2 I REF2 26 IN5 I CH5 Input 27 MUTE3 I Mute 3 28 SW45 I Select Switch For 4,5CH 3 FAN8045G3 22 SW45 MUTE3 FIN SVCC DO4+ SVCC 23 DO4- IN3 24 DO3+ IN4 25 DO3- REF2 26 GND IN5 27 MUTE4 MUTE3 28 PVCC2 SW45 Internal Block Diagram 21 20 19 18 17 16 15 PVCC2 GND MUTE4 LEVEL SHIFT 5K 5K LEVEL SHIFT 20K 20K 20K 5K sw45 10K 20K tsd monitor LEVEL SHIFT 10K LEVEL SHIFT 7 IN1 IN2 OPIN+ OPIN- OPOUT GND FIN 8 9 10 11 12 13 14 DO1+ 6 DO1- 5 DO2+ 4 GND DO2- 3 MUTE 12 GND 2 PVCC1 MUTE12 1 REF1 GND PVCC1 20K 4 FAN8045G3 Equivalent Circuits BTL Driver Output SW45 SVCC PVCC 11 12 20K 13 14 28 15 16 17 18 100K 100K 100K 100K 30K BTL Input(CH1,2) BTL Input(CH3,4) SVCC SVCC 23 2 5K 24 3 1K 10K 1K 26 2K 2K 2K Mute 9 20 27 5 50 1K 2K Reference 50K 1 50K 25 50K 50K FAN8045G3 Equivalent Circuits (Continued) OP-AMP Input OP-AMP Output SVCC SVCC 2K 2K 6 4 5 1K 2K 1K 2K 6 FAN8045G3 Absolute Maximum Ratings ( Ta=25°C) Parameter Maximum Supply Voltage Symbol Value Unit SVCCMAX 18 V PVCC1MAX 18 V PVCC2MAX 18 V PD 2.5note1,2,3 W Operating Temperature TOPR −35 ~ +85 °C Storge Temperature TSTG −55 ~ +150 °C Maximum Output Current IOMAX 1 A Power Dissipation Notes: 1. When it is mounted on 70mm × 70mm × 1.6mm PCB. 2. Power dissipation decreases at the rate of 20mW/°C in TA >25°C. 3. Do not exceed PD and SOA. Pd (mW) 3,000 2,000 SOA 1,000 0 0 25 50 75 100 125 150 175 Ambient temperature, Ta [°C] Recommended Operating Conditions ( Ta=25°C) Parameter Symbol Min. Typ. Max. Unit SVCC 4.5 - 14 V Operating Supply Voltage PVCC1 4.5 - SVCC V PVCC2 4.5 - SVCC V 7 FAN8045G3 Electrical Characteristics (SVCC = PVCC2 = 12V, TA = 25°C,PVCC1 = 5V , Ref1= 1.65V ,Ref2 = 2.5V , RL = 8Ω) Parameter Symbol Quiescent Circuit Current ICC Conditions Under no-load Min. Typ. Max. Unit - 17 25 mA - +50 mV BTL DRIVER CIRCUIT (RL=8Ω) Output Offset Voltage(CH12) VOOF1 VIN=1.65V -50 Output Offset Voltage(CH34) VOOF2 VIN=1.65V -100 - +100 mV Output Offset Voltage(CH5) VOOF3 VIN=2.5V -100 - +100 mV Maximum Output Voltage(CH12) VOM1 PVcc1=5V, RL=8Ω 3.6 4.0 - V Maximum Output Voltage(CH34) VOM2 PVcc2=12V, RL=24Ω 9.6 10.5 - V Close-loop Voltage Gain(CH12) AVF VIN= 0.3V 15.5 17.5 19.5 dB Close-loop Voltage Gain(CH34) AVF VIN= 0.3V 21.5 23.5 25.5 dB NORMAL OPAMP CIRCUIT(SVCC,PVCC2=12V) Input Offset Voltage VOF - -10 - +10 mV Input Bias Current IB1 - - - 300 nA VOH1 - 11 - - V Low Level Output Voltage VOL1 - - - 0.1 V Output Sink Current ISINK - 5 8 - mA Output Source Current ISOU1 - 1 5 - mA Open Loop Voltage Gain GVO1 f=1kHz, VIN= -75dB - 75 - dB RR1 f=120Hz, VIN= -20dB - 65 - dB SR1 f=120Hz, 2Vp-p - 1 - V/us f=1kHz, VIN= -20dB - 80 - dB - - 0.5 V 0.5 V High Level Output Voltage Ripple Rejection Ratio Slew Rate note1 note1 Common Mode Rejection Rationote1 TSD ON Voltage note1 CMRR1 Vtsdon - MUTE AND OTHER FUNCTION CIRCUIT Mute On Voltage VMON Pin9,20,27=Variation - - Mute Off Voltage VMOFF Pin9,20,27=Variation 2 - - V SW On Voltage VSWL Pin28=Variation - - 0.5 V SW Off Voltage VSWH Pin28=Variation 2 - - V Mute Low Level Sink Current IMTL VMUTE = 0V -15 0 15 uA Mute High Level Sink Current IMTH VMUTE = 5V - 85 170 uA SW45 Low Level Sink Current ISWL45 SW45 = 0V -15 0 15 uA SW45 High Level Sink Current ISWH45 SW45 = 5V - 85 170 uA REF1 Sink Current IRL REF1 = 1.65V - 52 104 uA REF2 Sink Current IRH REF2 = 2.5V - 85 170 uA Note: 1.Guaranteed field. ( No EDS/ Final test . ) 8 FAN8045G3 Application Information 1. MUTE,REF & SW45 Function INPUT SW45 MUTE12 MUTE3 OUTPUT MUTE4 REF1 PRE-AMP BTL REF2 OP CH12 CH3 CH4 CH4 CH5 H H H - H - ON ON IN5 ON ON ON H H L - H - ON OFF IN5 ON ON ON H H H - L - OFF OFF OFF OFF ON OFF H L H - H - OFF ON OFF ON ON ON H L L - H - OFF OFF OFF ON ON ON L - - L - - OFF OFF OFF OFF ON OFF L - - H - H OFF OFF IN4 OFF ON OFF L - - H - L OFF OFF OFF OFF ON OFF 2. TSD Function • When the chip temperature reaches to 167°C by abnormal condition, the TSD circuit is activated • During TSD Function is activated, OP-AMP Output (pin 6) remains below 0.5V. (TSD monitoring function). • This makes the bias current of the output drivers shut down, and all the output drivers are on cut-off state. Therefore the chip temperature begins to decrease. • When the chip temperature falls to 63°C, the TSD circuit is deactivated and the output drivers start to operate normally. SVCC IREF Output driver bias R1 Q0 R2 Hysteresis Ihys R3 3. Notice • If REF1(pin1) or REF2(pin25) is lower than 0.7V, BTL Output is off. • Under Voltage Protecton Function. ( If SVcc is lower than 3.8V, Chip is disable. Hysterisis is 0.2V) • Mute ON BTL OutPut Voltage is as followed: - Mute ON BTL Output (CH1,2) = (PVcc1 ) / 2 - Mute ON BTL Output (CH3,4) = ((PVcc2-0.6) / 2 • Each output to output and output to GND short should be kept away. 9 FAN8045G3 Typical Performance Characteristics Total Circuit Icc(mA) Icc(mA) <Temp vs Icc1> <Vcc vs Icc1> 25 25 20 20 15 15 10 10 5 5 SV cc=12V PV cc2=12V PV cc1=5V Temp=25 OC 0 0 4.5 5.5 6.5 7.5 8.5 -35 -25 -15 -5 9.5 10.5 11.5 12.5 13.5 14.5 5 15 25 35 45 55 65 75 85 Temp(°C) Vcc(V) BTL Drive Part Vom(V) Vom(V) <Vcc vs Vom2> <Vcc vs Vom1> 14 14 12 12 10 10 8 8 6 6 4 4 V in=0V RL=8 Ω 2 V in=0V RL=8 Ω 2 0 0 4 5 6 7 8 9 10 11 12 13 4 14 5 6 7 8 9 10 11 12 Vcc(V) <Vcc vs Vom4> <Vcc vs Vom3> 14 14 12 12 10 10 8 8 6 6 4 4 V in=0V RL=24 Ω 2 Vin=0V RL=24Ω 2 0 0 4 5 6 7 8 9 10 11 12 13 14 Vcc(V) 10 14 Vcc(V) Vom(V) Vom(V) 13 4 5 6 7 8 9 10 11 12 13 14 Vcc(V) FAN8045G3 Typical Performance Characteristics (Continued) Avf(dB) Avf(dB) <Vcc vs Avf2> <Vcc vs Avf1> 26 26 24 24 22 22 20 20 18 18 16 14 12 14 12 10 10 4 5 6 7 8 9 10 11 12 13 Temp=25 O C V in=0.3V Freg=1KHz RL=8 Ω 16 Temp=25 C V in=0.3V Freg=1KHz RL=8 Ω O 4 14 5 6 7 8 9 10 11 12 Avf(dB) Avf(dB) <Vcc vs Avf4> <Vcc vs Avf3> 26 26 24 24 22 22 20 20 18 18 16 16 Temp=25 O C V in=0.3V Freg=1KHz RL=24 Ω 14 12 5 6 7 8 9 10 11 12 13 Temp=25 O C V in=0.3V Freg=1KHz RL=24 Ω 14 12 10 10 4 14 5 6 7 8 9 10 11 12 Avf(dB) 13 14 Vcc(V) Vcc(V) Avf(dB) <Temp vs Avf1> <Temp vs Avf2> 24 24 22 22 20 20 18 18 16 SV cc=12V PV cc1=5V PV cc2=12V Freq=1KHz RL=8 Ω 14 12 V in=+0.3V 10 V in=-0.3V 8 16 SV cc=12V PV cc1=5V PV cc2=12V Freq=1KHz RL=8 Ω 14 12 V in=+0.3V 10 V in=-0.3V 8 -40 14 Vcc(V) Vcc(V) 4 13 -20 0 20 40 60 80 Temp(°C) -40 -20 0 20 40 60 80 Temp(°C) 11 FAN8045G3 Typical Performance Characteristics (Continued) Avf(dB) Avf(dB) <Temp vs Avf4> <Temp vs Avf3> 26 26 24 24 22 22 20 20 18 16 14 V in=+0.3V 12 18 SV cc=12V PV cc1=5V PV cc2=12V Freq=1KHz RL=24 Ω V in=-0.3V 14 -20 0 20 40 60 V in=+0.3V 12 V in=-0.3V 10 10 -40 SV cc=12V PV cc1=5V PV cc2=12V Freq=1KHz RL=24 Ω 16 -40 80 -20 0 20 40 60 Temp(°C) 80 Temp(°C) OP-AMP Part Isink(mA) Isou(mA) <Vcc vs Isink> <Vcc vs Isou> 60 10 50 8 40 6 30 4 20 2 10 0 0 4 5 6 7 8 9 10 11 12 13 14 4 5 6 7 8 9 10 11 12 Vcc(V) Isink(mA) 13 14 Vcc(V) Isou(mA) <Tem p vs Is ou> <Temp vs Isink> 60 10 50 8 40 6 30 4 20 2 10 0 0 -40 -20 0 20 40 60 80 Vcc(V) 12 -40 -20 0 20 40 60 80 Vcc(V) FAN8045G3 A A A A A A A 22 MUTE3 IN5 REF2 IN4 IN3 SVCC FIN 21 20 19 18 17 16 DO4- 23 V DO3+ 24 DO3- 25 GND 26 MUTE4 27 PVCC2 28 SW45 V 15 DO4+ A SW4 A SW3 Test Circuits 9 10 11 12 13 V 14 V A OP-AMP IN+ SW6 v OP-AMP INSW7 A SW1 IN- OUT SW2 IN+ A DO1+ 8 DO1- FIN DO2+ 7 DO2- 6 GND 5 MUTE12 4 PVCC1 OPIN+ 3 GND IN2 2 OPOUT IN1 1 OPIN- REF1 FAN8045G3 OUT SW8 SW9 13 FAN8045G3 Typical Application Circuit DO1+ 16 DO4- DO1- 13 17 DO3+ DO2+ 12 18 DO3- DO2- 11 GND 10 20 MUTE4 MUTE12 9 21 PVCC2 PVCC1 Focus Actuator Tracking Actuator M 19 GND 5V GND 7 23 IN3 OPOUT 6 24 IN4 OPIN- 5 25 REF2 OPIN+ 4 IN2 3 IN1 2 REF1 1 22 SVCC 0.1uF 26 IN5 27 MUTE3 14 VREF1 MUTE3 SLED SPINDLE SW45 VREF2 LOADING MUTE4 28 SW45 MICOM 0.1uF SERVO MUTE12 12V 8 FIN FIN 0.1uF FAN8045G3 12V TRACKING Spindle Motor 14 15 DO4+ FOCUS Sled & Loading M Motor FAN8045G3 Package Dimension 28-SSOPH-375-SG2 15 FAN8045G3 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 3/15/03 0.0m 001 Stock#DSxxxxxxxx 2003 Fairchild Semiconductor Corporation