The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. 0.5mm and 1mm Pitch Connectors For FPC/FFC FH12 Series Flip-lock ■Features 1. Ease of Use and Space Savings Only one finger or 6.9N (Newtons) of force is required to lock Hirose’s rotational actuator (flip-lock) as compared to using 2 fingers and 39.2N to close a FFC/FPC connector from our competition. Rotating One-touch Mechanism q The Flip-Lock design also allows customers to place 2 or more connectors side by side as there is no need to waste additional board space for a side latch. 2. Strengthened Flip-lock Actuator The standard Flip-Lock requires only 2.0mm height above the board. A strengthened lock lever is available which only requires an additional 0.4mm. w 3. Supports Thin FPC (0.18mm) Hirose does not require double-sided FPC to have any additional strengthening plate or stiffener and can therefore support a thickness of as little as 0.18mm +/0.05. 4. Hirose Ensures Reliability Hirose’s patented half tuning fork contacts maintain the required normal force without relying on the connector housing. With our competitor’s conventional products the housing walls support the contact force, which does not provide for long-term reliability. e 5. Prevention of Solder Bridge Excess solder cavity absorbs excessive solder and avoids solder bridging. 6. Three different assembly types FH12 is offered in Top & Bottom Contact and Vertical Mount and offered in both a 0.5mm contact pitch as well as a 1.0mm contact pitch (bottom contact only). 2010.9 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Product Specifications Current rating: 0.5A DC(Note 1) Operating Temperature Range:_40 to +85ç (Note 2) Storage Temperature Range:_10 to +50ç (Note 3) Rating Voltage rating: 50V AC Operating Humidity Range:Relative humidity, 90% max. Storage Humidity Range:Relative humidity, 90% max. (Not dewed) Applicable FPC Item 1. Insulation resistance 2. Withstanding voltage 3. Contact resistance 4. Durability (Insertion/withdrawal) 5. Vibration t=0.3±0.05 Gold plated t=0.18 ± 0.05 for FH12F-*S-0.5SH Specification 500M ohms minimum No flashover or insulation breakdown. 50m ohms maximum Conditions 100V DC 150V AC/1 minute 1mA Contact resistance: 50m ohms maximum No damage, cracks, or parts dislocation. No electrical discontinuity of 1µs or more Contact resistance: 50m ohms maximum. No damage, cracks, or parts dislocation. 20 cycles Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 10 cycles No electrical discontinuity of 1µs or more Contact resistance: 50m ohms maximum. No damage, cracks, or parts dislocation. 6. Shock Acceleration of 981 m/s2, 6 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis. Contact resistance: 50m ohms maximum. 7. Humidity(Steady state) Insulation resistance: 50M ohms minimum. No damage, cracks, or parts dislocation. 8. Temperature Cycle (Not dewed) 96 hours at 40ç and humidity of 90% to 95% Temperature: -40ç / 15 to 35ç / 85ç / 15 to 35ç, Time: 30 / 2 to 3 / 30 / 2 to 3(minutes) 5 cycles Contact resistance: 50m ohms maximum. Insulation resistance: 50M ohms minimum. No damage, cracks, or parts dislocation. No deformation of Reflow: At the recommended temperature profile Manual soldering: 350±10ç for 5 seconds components affecting performance. Note 1: When passing the current through all of the contacts,use 70% of the current rating. Note 2: Includes temperature rise caused by current flow. Note 3: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers nonconducting condition of installed connectors in storage, shipment or during transportation. Note 4: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. 9.Resistance to Soldering heat ■Material Part Material Finish Insulator Polyamide, LCP(60 pos.) Actuator PPS Contact Phosphor bronze Metal Fittings Brass Remarks Color : Beige UL94V-0 Color : Dark brown Gold plated ––––––– Tin plated ■Ordering Information **) FH 12 A - 10 (4) - S A - 0.5 SH (* q w e r t q Series Name : FH w Series No. : 12 e Blank : standard type A : Top contact type S : Type with strengthed flip-lock actuator F : Type with 0.18mm FPC End Thickness r Standard type : Number of contacts Eccentric type : Number of contacts in 0.5mm housing t Standard type : Blank Eccentric type : Number of contacts 2 y u i o !0 y Contact alignment: Single u Eccentric direction: Blank : standard type A : Eccentric type i Contacts Pitch : 0.5mm, 1mm o Contact type SH : SMT horizontal mounting type SV : SMT vertical mounting type !0 Plating specification (54) : Selective gold plated (55) : Gold plated The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Series Configuration Pitch Bottom Contact Type Top Contact Type Vertical mounting Type FPC conductive surface (bottom side) FPC conductive surface FH12- ** S-0.5SH 0.5mm P.4 Number of contacts 6, 8, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 24, 25, 26, 28, 30, 32, 33, 34, 35, 36, 40, 45, 50, 53 Type with Strengthened Lock Lever FH12S- ** S-0.5SH P.5 Number of contacts 30, 40, 45, 50, 53 Type with 0.18mm FPC End Thickness FH12A- ** S-0.5SH FH12F- ** S-0.5SH P.6 Number of contacts 6, 8, 10, 12, 13, 14, 15, 16, 18, 20, 22, 24, 25, 26, 28, 30, 32, 34, 36, 40 P.7 Number of contacts 10, 12 ,15, 16, 18, 20, 22, 24, 26, 28, 29, 30, 32, 33, 34, 36, 40, 42, 45, 50 FH12- ** S-0.5SV P.8 Number of contacts 10, 12, 13, 15, 16, 17, 18, 20, 22, 24, 26, 30, 32, 33, 34, 36, 40, 45, 49, 50, 60 FPC conductive surface (bottom side) 1mm Standard FH12- ** S-1SH P.9 Eccentric FH12- ** (**) SA-1SH Standard Number of contacts 5, 6, 7, 8, 9, 11, 12,16,17,22,26 Eccentric FH12- ** S-1SV P.10 Number of contacts 6, 7, 8, 16, 20, 22, Number of contacts 4, 6, 8, 10, 11, 14, 19, 24 24 3 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■0.5mm Pitch Bottom Contact Type A 0.5 (0.2) 1.2 2 0.8 Mated Cross-sectional Diagram FPC/FFC Contact Surface (2.1) (3.1) 5 2 (4.8) 1.85 B C D Note 1 Note 2 Note 3 Note 4 Note 5 CL No. Number of Contacts A B C D FH12-6S-0.5SH(**) 586-0582-5-** 6 2.5 06.1 7.1 3.57 FH12-8S-0.5SH(**) 586-0744-5-** 8 3.5 07.1 8.1 4.57 FH12-10S-0.5SH(**) 586-0522-3-** 10 4.5 08.1 9.1 5.57 FH12-11S-0.5SH(**) 586-0600-5-** 11 5.0 08.6 9.6 6.07 FH12-12S-0.5SH(**) 586-0704-0-** 12 5.5 09.1 10.1 6.57 FH12-13S-0.5SH(**) 586-0549-0-** 13 6.0 09.6 10.6 7.07 FH12-14S-0.5SH(**) 586-0533-0-** 14 6.5 10.1 11.1 7.57 FH12-15S-0.5SH(**) 586-0523-6-** 15 7.0 10.6 11.6 8.07 FH12-16S-0.5SH(**) 586-0531-4-** 16 7.5 11.1 12.1 8.57 FH12-17S-0.5SH(**) 586-0606-1-** 17 8.0 11.6 12.6 9.07 FH12-18S-0.5SH(**) 586-0530-1-** 18 8.5 12.1 13.1 9.57 FH12-19S-0.5SH(**) 586-0534-2-** 19 9.0 12.6 13.6 10.07 FH12-20S-0.5SH(**) 586-0524-9-** 20 9.5 13.1 14.1 10.57 FH12-22S-0.5SH(**) 586-0532-7-** 22 10.5 14.1 15.1 11.57 FH12-24S-0.5SH(**) 586-0521-0-** 24 11.5 15.1 16.1 12.57 FH12-25S-0.5SH(**) 586-0692-3-** 25 12.0 15.6 16.6 13.07 FH12-26S-0.5SH(**) 586-0576-2-** 26 12.5 16.1 17.1 13.57 FH12-28S-0.5SH(**) 586-0612-4-** 28 13.5 17.1 18.1 14.57 FH12-30S-0.5SH(**) 586-0525-1-** 30 14.5 18.1 19.1 15.57 FH12-32S-0.5SH(**) 586-0681-7-** 32 15.5 19.1 20.1 16.57 FH12-33S-0.5SH(**) 586-0520-8-** 33 16.0 19.6 20.6 17.07 FH12-34S-0.5SH(**) 586-0617-8-** 34 16.5 20.1 21.1 17.57 FH12-35S-0.5SH(**) 586-0740-4-** 35 17.0 20.6 21.6 18.07 FH12-36S-0.5SH(**) 586-0526-4-** 36 17.5 21.1 22.1 18.57 Note 5 FH12-40S-0.5SH(**) 586-0527-7-** 40 19.5 23.1 24.1 20.57 Note 5 FH12-45S-0.5SH(**) 586-0528-0-** 45 22.0 25.6 26.6 23.07 Note 5 FH12-50S-0.5SH(**) 586-0529-2-** 50 24.5 28.1 29.1 25.57 53 26.0 29.6 30.6 27.07 Note 5 4 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. : If there is no problem with the connector height, we recommend the type with the strengthened Fliplock actuator (FH12S-*S-0.5SH). Standard type connector height: 2 mm Connector height of type with strengthened Flip-lock actuator: 2.4 mm Unit:mm Part Number Note 5 4.6 5.6 FH12-53S-0.5SH(**) 586-0595-7-** Note 1 : Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels. Note 2 : (**):Specification. Refer to ordering information. (1.3) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■0.5mm Pitch Bottom Contact Type with Strengthened Flip-lock Actuator Mated Cross-sectional Diagram 1.2 2 0.8 A 0.5 ( 0.2 ) FPC/FFC Contact Surface ( 2.1) ( 3.1 ) (1.3 ) 2.25 D Note 1 Note 2 Note 3 Note 4 2 2.4 ( 4.8 ) B C 4.6 5.6 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit:mm Part Number CL No. Number of Contacts A B C D FH12S-30S-0.5SH(**) 586-0667-6-** 30 14.5 18.1 19.1 15.57 FH12S-40S-0.5SH(**) 586-0640-0-** 40 19.5 23.1 24.1 20.57 FH12S-45S-0.5SH(**) 586-0665-0-** 45 22.0 25.6 26.6 23.07 FH12S-50S-0.5SH(**) 586-0642-5-** 50 24.5 28.1 29.1 25.57 FH12S-53S-0.5SH(**) 586-0691-0-** 53 26.0 29.6 30.6 27.07 Note 1 : Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels. Note 2 : Indicates the specification. For details, please refer to the column "composition of product number". 5 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■0.5mm Pitch Bottom Contact Type with 0.18mm FPC End Thickness Applicable FPC end thickness : 0.18±0.05 A 0.5 ( 0.2 ) 1.2 2 0.8 Mated Cross-sectional Diagram FPC Contact Surface (2.15) (3.15) 2 ( 4.8 ) 1.85 B C D Note 1 Note 2 Note 3 Note 4 4.6 5.6 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit:mm Part Number CL No. Number of Contacts A B C D FH12F-6S-0.5SH(**) 586-0672-6-** 6 2.5 6.1 7.1 3.57 FH12F-8S-0.5SH(**) 586-0738-2-** 8 3.5 7.1 8.1 4.57 FH12F-10S-0.5SH(**) 586-0709-4-** 10 4.5 8.1 9.1 5.57 FH12F-12S-0.5SH(**) 586-0653-1-** 12 5.5 9.1 10.1 6.57 FH12F-13S-0.5SH(**) 586-0629-7-** 13 6.0 9.6 10.6 7.07 FH12F-14S-0.5SH(**) 586-0655-7-** 14 6.5 10.1 11.1 7.57 FH12F-15S-0.5SH(**) 586-0680-4-** 15 7.0 10.6 11.6 8.07 FH12F-16S-0.5SH(**) 586-0673-9-** 16 7.5 11.1 12.1 8.57 FH12F-18S-0.5SH(**) 586-0626-9-** 18 8.5 12.1 13.1 9.57 FH12F-20S-0.5SH(**) 586-0636-2-** 20 9.5 13.1 14.1 10.57 FH12F-22S-0.5SH(**) 586-0630-6-** 22 10.5 14.1 15.1 11.57 FH12F-24S-0.5SH(**) 586-0632-1-** 24 11.5 15.1 16.1 12.57 FH12F-25S-0.5SH(**) 586-0733-9-** 25 12.0 15.6 16.6 13.07 FH12F-26S-0.5SH(**) 586-0627-1-** 26 12.5 16.1 17.1 13.57 FH12F-28S-0.5SH(**) 586-0643-8-** 28 13.5 17.1 18.1 14.57 FH12F-30S-0.5SH(**) 586-0628-4-** 30 14.5 18.1 19.1 15.57 FH12F-32S-0.5SH(**) 586-0705-3-** 32 15.5 19.1 20.1 16.57 FH12F-34S-0.5SH(**) 586-0677-0-** 34 16.5 20.1 21.1 17.57 FH12F-36S-0.5SH(**) 586-0656-0-** 36 17.5 21.1 22.1 18.57 FH12F-40S-0.5SH(**) 586-0635-0-** 40 19.5 23.1 24.1 20.57 Note 1 : Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels. Note 2 : Indicates the specification. For details, please refer to the column "composition of product number". 6 (1.25) The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■0.5mm Pitch Top Contact Type A B C Mated Cross-sectional Diagram 0.5 (0.2) (1.9) FPC/FFC Contact Surface (1.45) (1.85) 5 (5) 6.2 2 (3.6) D E (0.45) 0.8 2.2 0.85 1.45 Note 1 Note 2 Note 3 Note 4 Note 5 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. : If there is no problem with the connector height, we recommend the type with the strengthened Fliplock actuator (FH12S-*S-0.5SH). Standard type connector height: 2 mm Connector height of type with strengthened Flip-lock actuator: 2.4 mm Unit:mm Part Number CL No. Number of Contacts A B C D E FH12A-10S-0.5SH(**) 586-0550-9-** 10 9.1 8.35 4.5 9.5 5.57 FH12A-12S-0.5SH(**) 586-0696-4-** 12 10.1 9.35 5.5 10.5 6.57 FH12A-15S-0.5SH(**) 586-0551-1-** 15 11.6 10.85 7.0 12.0 8.07 FH12A-16S-0.5SH(**) 586-0552-4-** 16 12.1 11.35 7.5 12.5 8.57 FH12A-18S-0.5SH(**) 586-0553-7-** 18 13.1 12.35 8.5 13.5 9.57 FH12A-20S-0.5SH(**) 586-0554-0-** 20 14.1 13.35 9.5 14.5 10.57 FH12A-22S-0.5SH(**) 586-0686-0-** 22 15.1 14.35 10.5 15.5 11.57 FH12A-24S-0.5SH(**) 586-0555-2-** 24 16.1 15.35 11.5 16.5 12.57 FH12A-26S-0.5SH(**) 586-0663-5-** 26 17.1 16.35 12.5 17.5 13.57 FH12A-28S-0.5SH(**) 586-0725-0-** 28 18.1 17.35 13.5 18.5 14.57 FH12A-29S-0.5SH(**) 586-0585-3-** 29 18.6 17.85 14.0 19.0 15.07 FH12A-30S-0.5SH(**) 586-0556-5-** 30 19.1 18.35 14.5 19.5 15.57 FH12A-32S-0.5SH(**) 586-0687-3-** 32 20.1 19.35 15.5 20.5 16.57 FH12A-33S-0.5SH(**) 586-0570-6-** 33 20.6 19.85 16.0 21.0 17.07 FH12A-34S-0.5SH(**) 586-0670-0-** 34 21.1 20.35 16.5 21.5 17.57 FH12A-36S-0.5SH(**) 586-0662-2-** 36 22.1 21.35 17.5 22.5 18.57 FH12A-40S-0.5SH(**) 586-0557-8-** 40 24.1 23.35 19.5 24.5 20.57 FH12A-42S-0.5SH(**) 586-0698-0-** 42 25.1 24.35 20.5 25.5 21.57 FH12A-45S-0.5SH(**) 586-0558-0-** 45 26.6 25.85 22.0 27.0 23.07 FH12A-50S-0.5SH(**) 586-0559-3-** 50 29.1 28.35 24.5 29.5 25.57 Note 1 : Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels. Note 2 : (**):Specification. Refer to ordering information. 7 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■0.5mm Pitch Vertical mounting Type Mated Cross-sectional Diagram ( 0.2 ) ( 0.15) FPC/FFC Contact Surface (1.4 ) ( 2.15 ) 1 1 0.5 F 2.5 0.5 ( 4.25 ) (1.75 ) 3.6 5.5 ( 4.85 ) A B 0.5 C D E Note 1 Note 2 Note 3 Note 4 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit:mm Part Number CL No. Number of Contacts A B C D E F FH12-10S-0.5SV(**) 586-0560-2-** 10 8.4 6.9 4.5 6.5 8.2 4 FH12-12S-0.5SV(**) 586-0615-2-** 12 9.4 7.9 5.5 7.5 9.2 4 FH12-13S-0.5SV(**) 586-0575-0-** 13 9.9 8.4 6.0 8.0 9.7 4 FH12-15S-0.5SV(**) 586-0561-5-** 15 10.9 9.4 7.0 9.0 10.7 4 FH12-16S-0.5SV(**) 586-0572-1-** 16 11.4 9.9 7.5 9.5 11.2 4 FH12-17S-0.5SV(**) 586-0601-8-** 17 11.9 10.4 8.0 10.0 11.7 4 FH12-18S-0.5SV(**) 586-0573-4-** 18 12.4 10.9 8.5 10.5 12.2 4 FH12-20S-0.5SV(**) 586-0562-8-** 20 13.4 11.9 9.5 11.5 13.2 4 FH12-22S-0.5SV(**) 586-0589-4-** 22 14.4 12.9 10.5 12.5 14.2 8 FH12-24S-0.5SV(**) 586-0563-0-** 24 15.4 13.9 11.5 13.5 15.2 8 FH12-26S-0.5SV(**) 586-0664-8-** 26 16.4 14.9 12.5 14.5 16.2 8 FH12-30S-0.5SV(**) 586-0564-3-** 30 18.4 16.9 14.5 16.5 18.2 8 FH12-32S-0.5SV(**) 586-0699-2-** 32 19.4 17.9 15.5 17.5 19.2 8 FH12-33S-0.5SV(**) 586-0565-6-** 33 19.9 18.4 16.0 18.0 19.7 8 FH12-34S-0.5SV(**) 586-0706-6-** 34 20.4 18.9 16.5 18.5 20.2 8 FH12-36S-0.5SV(**) 586-0641-2-** 36 21.4 19.9 17.5 19.5 21.2 8 FH12-40S-0.5SV(**) 586-0566-9-** 40 23.4 21.9 19.5 21.5 23.2 8 FH12-45S-0.5SV(**) 586-0567-1-** 45 25.9 24.4 22.0 24.0 25.7 8 FH12-49S-0.5SV(**) 586-0602-0-** 49 27.9 26.4 24.0 26.0 27.7 8 FH12-50S-0.5SV(**) 586-0568-4-** 50 28.4 26.9 24.5 26.5 28.2 8 FH12-60S-0.5SV(**) 586-0735-4-** 60 33.4 31.9 29.5 31.5 33.2 8 Note 1 : Embossed tape reel packaging (1,000 pieces/reel). Order by number of reels. Note 2 : (**):Specification. Refer to ordering information. 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■1mm Pitch Type Bottom Contact Type 2.3 E A 1.0 (0.2) 1.2 2 0.8 Mated Cross-sectional Diagram FPC/FFC Contact Surface (2.1) (3.1) (1.3) 2 (4.8) 1.85 B C D Note 1 Note 2 Note 3 Note 4 4.6 5.6 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit:mm Eccentric type Standard type Part Number CL No. Number of Contacts A B C D E FH12-5S-1SH(**) 586-0591-6-** 5 4 FH12-6S-1SH(**) 586-0607-4-** 6 5 8.6 9.6 6.07 2.3 9.6 10.6 7.07 2.3 FH12-7S-1SH(**) 586-0535-5-** 7 FH12-8S-1SH(**) 586-0579-0-** 8 6 10.6 11.6 8.07 2.3 7 11.6 12.6 9.07 2.3 FH12-9S-1SH(**) 586-0540-5-** FH12-11S-1SH(**) 586-0668-9-** 9 8 12.6 13.6 10.07 2.3 11 10 14.6 15.6 12.07 2.3 FH12-12S-1SH(**) 586-0741-7-** FH12-16S-1SH(**) 586-0536-8-** 12 11 15.6 16.6 13.07 2.3 16 15 19.6 20.6 17.07 2.3 FH12-17S-1SH(**) 586-0739-5-** 17 16 20.6 21.6 18.07 2.3 FH12-22S-1SH(**) 586-0547-4-** 22 21 25.6 26.6 23.07 2.3 FH12-26S-1SH(**) 586-0592-9-** 26 25 29.6 30.6 27.07 2.3 FH12-10(4)SA-1SH(**) 586-0537-0-** 4 3 8.1 9.1 5.57 2.8 FH12-14(6)SA-1SH(**) 586-0538-3-** 6 5 10.1 11.1 7.57 2.8 FH12-18(8)SA-1SH(**) 586-0539-6-** 8 7 12.1 13.1 9.57 2.8 FH12-22(10)SA-1SH(**) 586-0541-8-** 10 9 14.1 15.1 11.57 2.8 FH12-24(11)SA-1SH(**) 586-0542-0-** 11 10 15.1 16.1 12.57 2.8 FH12-30(14)SA-1SH(**) 586-0543-3-** 14 13 18.1 19.1 15.57 2.8 FH12-40(19)SA-1SH(**) 586-0546-1-** 19 18 23.1 24.1 20.57 2.8 FH12-50(24)SA-1SH(**) 586-0548-7-** 24 23 28.1 29.1 25.57 2.8 Note 1: Embossed tape reel packaging (2,000 pieces/reel). Order by number of reels. Note 2: The 1mm version of FH12 is constructed by loading every other contact into the 0.5mm housing. When a housing designed for an odd number of 0.5mm pitch contacts is used; the spacing from the edge to the first contact on either side is the same as the distance between each contact, 1.0mm. Hirose considers this design to be a standard-type 1.0mm connector. An eccentric-type connector using a housing designed for an even number of 0.5mm pitch contacts and consequently one side has 1.5mm distance from the edge to the first contact. (See FPC/FFC dimensional drawing on page 19) The part number for the eccentric type describes the size of the 0.5mm housing used and lists the number of 1.0mm pitch contacts in parentheses () as shown in the above table. 9 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■1mm Pitch Vertical Mounting Type Mated Cross-sectional Diagram 2 FPC/FFC Contact Surface (0.15) (1.4) (2.15) (0.2) 2 0.5 F 2.5 0.5 (4.25) (1.75) 3.6 5.5 (4.85) A B 1.0 3.8 (Metal fitting dimension) C D E Note 1 Note 2 Note 3 Note 4 : The coplanarity of each terminal lead within specified dimension is 0.1 mm Max. : Packaged on tape and reel only. Check packaging specification. : Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. : After reflow, the terminal plating may change color, however this does not represent a quality issue. Unit:mm Part Number CL No. Number of Contacts A B C D FH12-6S-1SV(**) 586-0605-9-** FH12-7S-1SV(**) 586-0610-9-** FH12-8S-1SV(**) FH12-16S-1SV(**) 6 9.9 8.4 5 7 10.9 9.4 6 586-0593-1-** 8 11.9 10.4 586-0574-7-** 16 19.9 18.4 FH12-20S-1SV(**) 586-0634-7-** 20 23.9 22.4 FH12-22S-1SV(**) 586-0584-0-** 22 25.9 24.4 FH12-24S-1SV(**) 586-0594-4-** 24 27.9 26.4 Note 1 : Embossed tape reel packaging (1,000 pieces/reel). Order by number of reels. Note 2 : (**):Specification. Refer to ordering information. 10 E F 8 9.7 4 9 10.7 4 7 10 11.7 4 15 18 19.7 8 19 22 23.7 8 21 24 25.7 8 23 26 27.7 8 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Recommended FPC/FFC dimensions and Land/Metal Mask dimensions ●0.5mm Pitch Product C±0.1 0.3±0.03(Land) 1.3±0.1 C 0.5±0.1 Product Type C Dimension Types other than 0.3±0.05min those below Stiffener thickness should be 0.188 mm (7.5 mil) min FH12F 0.18±0.05 0.5±0.05 0.25±0.03(Metal mask) A±0.05 Recommended metal mask thickness : 0.15mm Unit: mm Number of Contacts 6 8 10 11 12 13 14 15 16 17 18 19 20 22 24 Dimension A B 2.5 3.5 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.5 11.5 3.5 4.5 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.5 12.5 Number of Contacts 25 26 28 29 30 32 33 34 35 36 40 42 45 50 53 Unit: mm A B Dimension Number of Contacts 12.0 12.5 13.5 14.0 14.5 15.5 16.0 16.5 17.0 17.5 19.5 20.5 22.0 24.5 26.0 13.0 13.5 14.5 15.0 15.5 16.5 17.0 17.5 18.0 18.5 20.5 21.5 23.0 25.5 27.0 6 8 10 11 12 13 14 15 16 17 18 19 20 22 24 A B 2.5 3.5 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.5 11.5 8.1 9.1 10.1 10.6 11.1 11.6 12.1 12.6 13.1 13.6 14.1 14.6 15.1 16.1 17.1 C Dimension Number of Contacts A B C 4.5 5.5 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.5 13.5 25 26 28 29 30 32 33 34 35 36 40 42 45 50 53 12.0 12.5 13.5 14.0 14.5 15.5 16.0 16.5 17.0 17.5 19.5 20.5 22.0 24.5 26.0 17.6 18.1 19.1 19.6 20.1 21.1 21.6 22.1 22.6 23.1 25.1 26.1 27.6 30.1 31.6 14.0 14.5 15.5 16.0 16.5 17.5 18.0 18.5 19.0 19.5 21.5 22.5 24.0 26.5 28.0 0.5±0.05 0.5±0.1 0.35±0.03(FPC) 0.3±0.05 1±0.05 1±0.05 0.5±0.1 1.8±0.1 1.8±0.1 1.5±0.1 1.5±0.1 4.5±0.1 0.5±0.05 0.3±0.03(FFC) A±0.05 B±0.07 Odd contact number No.1 contact A±0.1 0.8±0.1(Land) 0.65±0.05(Metal mask) 1.8±0.1 1.8±0.1 2MIN 3MIN Even contact number 0.6±0.1(Land) 0.5±0.05 0.5±0.05(Metal mask) 1±0.05 1±0.05 1±0.05 B±0.05 0.6±0.1(Land) B±0.05 Unit: mm Dimension Number of Contacts 10 12 13 15 16 17 18 20 22 24 A B 04.5 05.5 06.0 07.0 07.5 08.0 08.5 09.5 10.5 11.5 05.5 06.5 07.0 08.0 08.5 09.0 09.5 10.5 11.5 12.5 Dimension Number of Contacts 26 30 32 33 34 36 40 45 49 50 60 0.5±0.05(Metal mask) 1±0.05 Recommended metal mask thickness : 0.15mm *Set the stiffener thickness to 0.188 (7.5mil) min. 0.5mm Pitch Vertical Mounting Type No.1 contact A±0.1 0.8±0.1(Land) 0.65±0.05(Metal mask) 1.5±0.1 Dimension 1.5±0.1 4.5±0.1 0.5mm Pitch Top Contact Type 0.35±0.03(FPC) 0.3±0.03(FFC) A±0.05 B±0.07 B±0.1 1.5±0.1 4.5MIN 3.5MIN 0.5±0.05 0.5±0.1 0.5mm Pitch Bottom Contact Type Land / Metal Mask dimensions 2.2±0.1 FPC/FFC dimensions A B 12.5 14.5 15.5 16.0 16.5 17.5 19.5 22.0 24.0 24.5 29.5 13.5 15.5 16.5 17.0 17.5 18.5 20.5 23.0 25.0 25.5 30.5 Unit: mm Dimension Number of Contacts 10 12 13 15 16 17 18 20 22 24 A B 06.5 07.5 08.0 09.0 09.5 10.0 10.5 11.5 12.5 13.5 04.5 05.5 06.0 07.0 07.5 08.0 08.5 09.5 10.5 11.5 Dimension Number of Contacts 26 30 32 33 34 36 40 45 49 50 60 A B 14.5 16.5 17.5 18.0 18.5 19.5 21.5 24.0 26.0 26.5 31.5 12.5 14.5 15.5 16.0 16.5 17.5 19.5 22.0 24.0 24.5 29.5 11 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Recommended FPC/FFC dimensions and Land/Metal Mask dimensions ●1mm Pitch Product FPC/FFC dimensions Land / Metal Mask dimensions Recommended metal mask thickness : 0.15mm πSet the stiffener thickness to 0.188 (7.5mil) min. Unit: mm 1mm Pitch Vertical Mounting Type B C 5 6 7 8 9 11 12 16 17 22 26 04 05 06 07 08 10 11 15 16 21 25 06 07 08 09 10 12 13 17 18 23 27 1 1 1 1 1 1 1 1 1 1 1 A B C 4 6 8 10 11 14 19 24 03 05 07 09 10 13 18 23 05.5 07.5 09.5 11.5 12.5 15.5 20.5 25.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 *Set the stiffener thickness to 0.188 (7.5mil) min. Unit: mm Dimension A Number of Contacts 5 6 7 8 9 11 12 16 17 22 26 04 05 06 07 08 10 11 15 16 21 25 B C D 10.6 11.6 12.6 13.6 14.6 16.6 17.6 21.6 22.6 27.6 31.6 07 08 09 10 11 13 14 18 19 24 28 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 12 Number of Contacts A B 6 7 8 16 20 22 24 05 06 07 15 19 21 23 07 08 09 17 21 23 25 03 05 07 09 10 13 18 23 4 6 8 10 11 14 19 24 B Unit: mm Dimension Number of Contacts A B 6 7 8 16 20 22 24 08 09 10 18 22 24 26 05 06 07 15 19 21 23 C 10.1 06.5 12.1 08.5 14.1 10.5 16.1 12.5 17.1 13.5 20.1 16.5 25.1 21.5 30.1 26.5 Recommended metal mask thickness : : 0.15mm Unit: mm Dimension Dimension A Number of Contacts Eccentric Type A Dimension Number of Contacts Standard Type Dimension Number of Contacts Eccentric Type Standard Type 1mm Pitch Bottom Contact Type D 2 2 2 2 2 2 2 2 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Packaging Specification Embossed Carrier Tape Dimensions Horizontal Type (Common to Bottom/Top Contact, 0.5mm/1mm Pitch) (2.0) Flat surface for placement with Automatic equipment 3) Reel Dimensions (Common to All Types) (ø1 (D : INSIDE) Mounting portion Lead portion (400mm min.) ( ( ) ) End portion Embossed carrier tape Blank portion ( E : OUTSIDE) (10 pockets min.) ●0.5mm Pitch Bottom/Top Contact Type Unit:mm Dimension Number of Contacts A B C D E 6 8 10 11 12 13 14 15 16 17 18 19 20 22 24 16 16 16 16 24 24 24 24 24 24 24 24 24 24 24 ---------------------------------------------------------------------------------------------------------------------------------------- 07.5 07.5 07.5 07.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 11.5 17.4 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 25.4 21.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 29.4 Dimension Number of Contacts A B 25 ---------24 26 ---------24 28 28.4 32 29 28.4 32 30 28.4 32 32 28.4 32 33 28.4 32 34 28.4 32 35 40.4 44 36 40.4 44 40 40.4 44 42 40.4 44 45 40.4 44 50 40.4 44 53 40.4 44 Note: 2,000 pieces per reel. ● 1mm Pitch Bottom Contact Type C D E 11.5 11.5 14.2 14.2 14.2 14.2 14.2 14.2 20.2 20.2 20.2 20.2 20.2 20.2 20.2 25.4 25.4 33.4 33.4 33.4 33.4 33.4 33.4 45.4 45.4 45.4 45.4 45.4 45.4 45.4 29.4 29.4 37.4 37.4 37.4 37.4 37.4 37.4 49.4 49.4 49.4 49.4 49.4 49.4 49.4 Unit:mm Dimension Number of Contacts A B C D E 5 6 7 8 9 11 12 16 17 22 26 16 24 24 24 24 24 24 32 44 44 44 ---------------------------------------------------------------28.4 40.4 40.4 40.4 07.5 11.5 11.5 11.5 11.5 11.5 11.5 14.2 20.2 20.2 20.2 17.4 25.4 25.4 25.4 25.4 25.4 25.4 33.4 45.4 45.4 45.4 21.4 29.4 29.4 29.4 29.4 29.4 29.4 37.4 49.4 49.4 49.4 Dimension Number of Contacts A 4 16 6 24 8 24 10 24 11 24 14 32 19 44 24 44 Note: 2,000 pieces per reel. Eccentric Type Standard Type Top cover tape Blank portion (10 pockets min.) B C D E ---------------------------------------------28.4 40.4 40.4 07.5 11.5 11.5 11.5 11.5 14.2 20.2 20.2 17.4 25.4 25.4 25.4 25.4 33.4 45.4 45.4 21.4 29.4 29.4 29.4 29.4 37.4 49.4 49.4 13 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC Vertical Mounting Type (Common to 0.5mm/1mm Pitch) Flat surface for placement with Automatic equipment (1.75) ●0.5mm Pitch Vertical mounting Type Dimension Number of Contacts A B C D 10 16 ---------- 07.5 12 16 ---------- 07.5 13 24 ---------- 15 24 ---------- 16 24 17 24 18 20 Unit:mm E Dimension Number of Contacts A B C D E 17.4 21.4 26 24 ---------- 11.5 25.4 29.4 17.4 21.4 30 32 28.4 14.2 33.4 37.4 11.5 25.4 29.4 32 32 28.4 14.2 33.4 37.4 11.5 25.4 29.4 33 32 28.4 14.2 33.4 37.4 ---------- 11.5 25.4 29.4 34 44 40.4 20.2 45.4 49.4 ---------- 11.5 25.4 29.4 36 44 40.4 20.2 45.4 49.4 24 ---------- 11.5 25.4 29.4 40 44 40.4 20.2 45.4 49.4 24 ---------- 11.5 25.4 29.4 45 44 40.4 20.2 45.4 49.4 22 24 ---------- 11.5 25.4 29.4 49 44 40.4 20.2 45.4 49.4 24 24 ---------- 11.5 25.4 29.4 50 44 40.4 20.2 45.4 49.4 60 56 52.4 26.2 57.4 61.4 Note: 1,000 pieces per reel. ●1mm Pitch Vertical mounting Type Dimension Number of Contacts A B C D E 6 24 ---------- 11.5 25.4 29.4 7 24 ---------- 11.5 25.4 29.4 8 24 ---------- 11.5 25.4 29.4 16 32 28.4 14.2 33.4 37.4 20 44 40.4 20.2 45.4 49.4 22 44 40.4 20.2 45.4 49.4 24 44 40.4 20.2 45.4 49.4 Note: 1,000 pieces per reel. 14 Unit:mm The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■FH12 Series FPC/FFC Construction (Recommended Specifications) 1. FFC FFC : Flexible Flat Cable Material Name Material Thickness (µm) (12) Polyester film Adhesive Thermoplastic polyester (30) (Nickel under plated / Gold plated), soft copper film Adhesive 35 30 Polyester type Polyester 12 Adhesive Polyester type 30 Stiffener Polyester type 188 Total 295 (Note) *Real tolerance of thickness dimension is on the order of ±20 µm (275 to 315 µm) Note: Use of a thicker FFC results in a stiffer lock action and the lock is more easily released. A factor that contributes to thicker FFC is the use of 250 µm stiffener which is thicker than the standard (188 µm) product. This results in a total thickness of 357 µm. When using FFC, control of FFC thickness becomes easy if you indicate to us the thickness of the stiffener. 2. FPC FPC : Flexible Printed Circuit Material Material Name Covering layer film Polyimide 1 mil Thickness (µm) (25) (25) Cover adhesive Surface treatmenta Nickel under plated 1to 5µm / Gold plated 0.2µm Copper foil Cu Base adhesive Heat-hardened adhesive 25 Base film Polyimide 1 mil 25 1oz Reinforcement material adhesive Heat-hardened adhesive Stiffener 3 35 30 Polyimide 7 mil 175 Total 293 3. Precautions 1. This specification is a recommendation for the construction of the FH12 Series FPC and FFC (t=0.3 ±0.05). 2. For details about the construction, please contact the FPC/FFC manufacturers. 15 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Recommended Temperature Profile MAX 250ç 250 Temperature 230ç 200 200ç 150 150ç (ç) 100 HRS test conditions Solder method :Reflow, IR/hot air Environment: :Room air Solder composition :Paste, 96.5%Sn/3%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.’s Part Number: M705-221CM5-32-10.5) Test board :Glass epoxy 40mm∞80mm∞1.6mm thick Land dimensions :Top and bottom contact type 0.3mm∞1.3mm Vertical mounting type 0.6mm∞1.5mm Metal mask :Top and bottom contact type 0.25mm∞1.3mm∞0.15mm thick Vertical mounting type 0.5mm∞1.5mm∞0.15mm thick 50 25ç (60 seconds) 90 to 120 seconds 30 seconds 0 Start 60 Preheating 120 Time 16 Soldering This temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ■Connector Operating Instructions, precautions and recommendations ●Bottom Contact Type (common for 0.5mm/1mm Pitch) Operation Precautions 1. FPC/FFC Termination procedure. Connector installed on the board. 1) Avoid grasping the actuator with two fingers or lifting the actuator with fingernail. 1) Lift up the actuator. Use thumb or index finger. 2) Do not use a thin tool such as the tip of a screwdriver to release the lock lever. Doing so will cause deformation of the contacts. 3) Do not apply force in the direction of arrows A, B, or C while the lock lever is open. Doing so will cause the lock lever to become disen gaged, or will damage the hook portion of the connector body. 2) Fully insert the FPC/FFC parallel to mounting surface, with the exposed conductive traces facing down. 4) When inserting the FPC/FFC, do not forcefully rub against the surface beneath the connector insertion slot. Doing so will result in the FPC/FFC forcefully striking the contacts and this will cause contact deformation, peeling of the FPC/FFC conductors, and other irregularities. FPC/FFC conductive traces 5) Insert the FPC/FFC at the proper position of the connector insertion slot, and insert perpendicularly with respect to the connector. Improper insertion will cause continuity problems, disengagement of the lock lever, and damage to the hook portion. 17 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ●Bottom Contact Type (common for 0.5mm/1mm Pitch) Operation Precautions 3) Rotate down the actuator until firmly closed. It is critical that the inserted FPC/FFC is not moved and remains fully inserted. Should the FPC/FFC be moved, open the actuator and repeat the process, starting with Step 1. 6) Partial insertion of the FPC/FFC, offset insertion, and diagonal insertion will result in an unfavorable engagement of the lock lever in which the lock lever is raised. To correct this, first remove the FPC/FFC and then reinsert it. Forcing the lock will damage the connector. Stiffener 7) When locking, handle the FPC/FFC so that a load is not applied to the FPC/FFC as would occur by pulling the FPC/FFC, or lifting it, etc. When a load is applied in the opposite direction to the rotational movement of the lock, an excessive load will be applied and this will cause connector damage. 2. FPC/FFC Removal 1) Lift up the actuator. 2) Carefully remove the FPC/FFC. 8) At the time of lock operation, application of force such as that indicated by the arrows in the diagrams below will cause the lock lever to disengage. When the lock lever has become disengaged, please exchange the entire connector. 18 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ●Top Contact Type Operation Precautions 1. FPC/FFC Termination procedure. Connector installed on the board. 1) Lift up the actuator. Use thumb or index finger. 1) Avoid further lifting of the lock lever once the lock has been released. Doing so will cause the lock lever to separate from the rotational shaft, and the lock lever will become disengaged or the hook portion of the connector body will be damaged. Lock lever Rotational shaft 2) Fully insert the FPC/FFC parallel to mounting surface, with the exposed conductive traces facing UP. a are ion t r nse Ci FP FPC/FFC conductive traces 2) Avoid further pressing of the lock portion from the locked condition when the FPC/FFC has not yet been inserted. Doing so will cause the lock lever to become disengaged from the rotational shaft, and the hook portion of the connector body will be damaged. Stiffener 3) Rotate down the actuator until firmly closed. It is critical that the inserted FPC/FFC is not moved and remains fully inserted. Should the FPC/FFC be moved, open the actuator and repeat the process, starting with Step 1 above. 3) Do not insert the FPC/FFC diagonally. Doing so will result in the corners of the FPC/FFC catching on the contacts and will cause deformation of the contacts. 2. FPC/FFC Removal 1) Lift up the actuator. 2) Carefully remove the FPC/FFC. 4) When closing down the actuator apply equal pressure to both sides of the actuator. 19 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. FH12 Series●0.5mm and 1mm Pitch Connectors For FPC/FFC ●Vertical Mounting Type (common for 0.5mm/1mm Pitch) Operation Precautions 1. FPC/FFC Termination procedure. Connector installed on the board. 1) Avoid forcing the actuator up or down without the FPC/FFC inserted. 1) Verify that the actuator is positioned upright. If the actuator has rotated to the side, carefully rotate it upright. Actuator upright 2) Insert the FPC/FFC vertically in the connector slot assuring that the conductive traces of the FPC/FFC are facing away from the actuator. FPC/FFC conductive traces Stiffener 2) Do not insert the FPC/FFC diagonally. Doing so will result in the corners of the FPC/FFC catching on the contacts and will cause deformation of the contacts. Sl ot 3) Press down the actuator in the direction shown. 2. FPC/FFC Removal Rotate the actuator upward and withdraw the FPC/FFC. ® 20 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-5300, FAX: 81-3-3495-5230 http://www.hirose.com http://www.hirose-connectors.com The contents of this catalog are current as of date of 09/2010. Contents are subject to change without notice for the purpose of improvements.