ETC FLATRON995FT(FB995C

SPECIFICATIONS
1. PICTURE TUBE
Size
DefIection Angle
Neck Diameter
Phosphor
Stripe Pitch
Low Radiation
Face Treatment
: 19 inch (Flat Slot Mask)
: 90°
: 29.1 mm
: P22
: 0.24 mm
: TCO-99, MPR-II
: AR-ASC coating
2. SIGNAL
2-1. Horizontal & Vertical Sync
1) Input Voltage Level : Low= ≤0.8V, High= ≥2.1V
2) Sync Polarity
: Positive or Negative
2-2. Video Input Signal
1) Voltage Level
a) Color 0, 0
b) Color 7, 0
c) Color 15, 0
2) Input Impedance
3) Video Color
4) Signal Format
: 0 ~ 0.7 Vp-p
: 0 Vp-p
: 0.467 Vp-p
: 0.7 Vp-p
: 75 Ω
: R, G, B Analog
: Refer to the Timing Chart
2-3. Signal Connector
15 Pin D-Sub Connector, Attached
2-4. Scanning Frequency
Horizontal
: 30 ~ 96 kHz
Vertical
: 50 ~ 160 Hz
4-2. Display Color
: Full Colors
4-3. Display Resolution : 1600 Dots x 1200Lines/75Hz
4-4. Video Bandwidth
: 203MHz
5. ENVIRONMENT
5-1. Operating Temperature: 10°C ~ 35°C (50°F ~ 95°F)
(Ambient)
5-2. Relative Humidity
: 8% ~ 80%
(Non-condensing)
5-3. Altitude
: 5000m
6. DIMENSIONS (with TILT/SWIVEL)
Width
: 470 mm (18.60")
Depth
: 470 mm (18.60")
Height
: 480 mm (18.90")
7. WEIGHT (with TILT/SWIVEL)
Net Weight
: 25.7 kg (56.67 lbs)
Gross Weight
: 28.6 kg (63.06 lbs)
8. USB Specifications
USB Standard
: Rev. 1.0 complied self-powered hub
Downstream power supply : 500mA for each (MAX)
Communication speed : 12 Mbps (Full), 1.5 Mbps (Low)
USB port
: 1 Upstream port
4 Downstream ports
3. POWER SUPPLY
3-1. Power Range
AC 90~264V, 50/60Hz 2.0A (NON PFC)
AC 200~240V 50Hz 1.5A (PFC Version)
3-2. Power Consumption
MODE
4. DISPLAY AREA
4-1. Active Video Area :
• Max Image Size - 366.0 x 274.5mm (14.40" x 10.80")
• Preset Image Size - 350 x 262 mm (13.78" x 10.31")
H/V SYNC
POWER CONSUMPTION
LED COLOR
NORMAL (ON)
ON/ON
less than 140W
GREEN
STAND-BY
OFF/ON
less than 8W
SUSPEND
ON/OFF
less than 8W
OFF
OFF/OFF
less than 3W
ORANGE
ORANGE
WIRING DIAGRAM
Anode Cap
Purity
Convergence
P301
P319
P306
P302
P303
Degauss
Tilt
CDT Earth
Purity
DY
Degauss
P801
P704
P903
P612
P404
(CONV H/V)
P403
P610
P991
P904
Main PCB
P401
P990
P992
P402
P101
- 10 -
P611
PFC
BLOCK DIAGRAM
- 14 -
DESCRIPTION OF BLOCK DIAGRAM
1. Line Filter & Associated Circuit
This is used for suppressing noise of power input line
flowing into the monitor and/or some noise generated in
this monitor flowing out through the power input line.
That is to say, this circuit prevents interference between
the monitor and other electric appliances.
2. Degauss Circuit & Coil
The Degauss circuit consists of the degaussing coil, the
PTC (Positive Temperature Coefficient) thermistor
(TH901), and the relay(RL901). This circuit eliminates
abnormal color of the screen automatically by
degaussing the slot mask in the CRT when turn on the
power switch. When you need to degauss while using
the monitor select DEGAUSS in the SPECIAL on the
OSD menu.
3. SMPS(Switching Mode Power Supply).
This circuit works with power of 90~132Vac/ 196~
264Vac (50/60Hz).
The operation procedure is as follows:
1) AC input voltage is rectified and smoothed by the bridge
diode (D901) and capacitors (C912).
2) The rectified voltage (DC voltage) is applied to the
primary coil of the transformer (T901,T902).
3) The control IC (IC901) generates switching pulse to turn
on and off the primary coil of the transformer (T902)
repeatedly.
4) Depending on the turn ratio of the transformer , the
secondary voltages appear at the secondary coil of the
transformer (T902).
5) These secondary voltages are rectified by each diode
(D922.923,924,926,925,933) and operate the other
circuits. (Deflection , Video Amplifier ,..... etc.).
The switching IC (IC901) controls input-pulse-width and
generates secondary voltages by sub-transformer
(T901).
4. Display Power Management Circuit.
This circuit control power consumption of the monitor by
detecting H and V sync signal.
There are Stand-by and suspend mode.
When no horizontal or vertical sync signal input, the
circuit consists of Q903 and IC913 becomes stand-by
and suspend mode. Its power consumption is below
8W.
5. X-ray Protection.
This circuit detects the rectified DC voltage comes from
the FBT pin 6. If the high volltage of the FBT reaches up
to about 30kV (abnormal state), high voltage control
PWM IC (IC1001) detects it. And PWM IC (IC1001)
prevent output voltage to the gate of switching FET
(Q507). It stops operating primary circuit of the FBT
(T703), and high voltage is not be generated.(In the
normal state, the high voltage is about 27kV.)
6. Micom (Microprocessor) Circuit.
The operating procedure of Micom (Microprocessor) and
its associated circuit is as follows:
1) H and V Sync signal is supplied from the D-sub to the
Micom (IC201).
2) The Micom (IC201) distinguishes polarity and frequency
of H and V sync.
3) The Micom controls each OSD function signals.(H-size,
H-position, V-size, etc.)
4) The controlled data of each mode is stored in itself. User
can adjust screen condition by each OSD function. The
data of the adjust screen condition is stored
automatically.
7. Horizontal and Vertical Synchronous Processor
This circuit generates the horizontal drive pulse and the
vertical drive pulse by taking sync-signal from the signal
cable. This circuit consists of the TDA4856 (IC701) and
the associated circuit.
8. Oscillating Circuit for D/D Converter.
This circuit generates the saw-tooth wave which has the
horizontal period by taking the output of the TDA4856
(IC701).
9. D/D (DC to DC) Converter.
This circuit supplies DC voltage to the horizontal
deflection output circuit by decreasing DC 190V which is
the secondary voltage of the SMPS in accordance with
the input horizontal sync signal.
10. Side-Pincushion Correcting Circuit.
This circuit improves the side-pincushion of the screen
by mixing east-west wave to the output of the horizontal
deflection D/D converter which is used for the supply
voltage source (B+) of the deflection circuit.
11. D/D Drive & Convert Circuit.
This circuit is used for supplying B+ voltage to horizontal
deflection output transistor(Q707). This circuit makes to
add side-pincushion correcting signal to B+ voltage.
12. Horizontal Deflection Output Circuit.
This circuit makes the horizontal deflection by supplying
the saw-tooth current to the horizontal deflection yoke.
13. High Voltage Output & FBT (Fly Back Transformer).
The high voltage output circuit is used for generating
pulse wave to the primary coil of the FBT (Fly Back
Transformer (T703)). A boosted voltage (about 27kV)
appears at the secondary of the FBT and it is supplied to
the anode of the CRT. And there are another output
voltages such as the dynamic focus frequency.
14. H-Linearity Correction Circuit.
This circuit corrects the horizontal linearity for each
horizontal sync frequency.
- 15 -
15. Vertical Output Circuit.
This circuit takes the vertical ramp wave form the
TDA4856(IC701) and performs the vertical deflection by
supplying the saw-tooth wave current form the TDA8172
(IC601) to the vertical deflection yoke.
21. OSD Circuit.
This circuit is used for performing the OSD (On Screen
Display) function. When a user selects the OSD Select/
Adjustment control, the adjustment status displays on
the screen.
16. Dynamic Focus Output circuit.
This circuit takes H and V parabola wave from the
TDA4856(IC701) and amplifies these waves to offer to
the FBT(T703).
22. Video Pre-Amp Circuit.
This circuit amplifies the analog video signal from 0-0.7V
to 0-4V. This circuit is operated by taking the clamp, R,
G, B drives, and contrast signals from the Micom
(IC201).
17. H & V Blanking and Brightness Control.
This circuit eliminates the retrace line by supplying a
negative pulse to the G1 of the CRT. The brightness
control circuit is used to control of the screen brightness
by changing the DC level of G1.
23. Video Output Amp Circuit.
This circuit amplifies the video signal which comes from
the video pre-amp circuit and amplified video signal is
applied to the CRT cathode.
18. Tilt (Image Rotation) Circuit.
This circuit corrects the tilt of the screen by supplying the
image rotation signal to the tilt coil which is attached to
the CRT near the deflection.
19. Static Convergence Control Circuit.
This circuit corrects the convergence of the screen by
supplying the convergence signal to the 4H(STC) coil
which is attached to the CRT near the deflection.
20. Moiré Reduction Circuit.
This circuit reduce interference between the periodical
display pattern and the CRT’s slot (or dot). The positions
of every other one dot video signal beams (red, green
and blue beam) are shifted finely, thus reducing
interference.
- 16 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK
FUSE OK?
NO
TROUBLE IN
FUSE (F901)
NO
TROUBLE IN
D901
YES
CHECK
C912 (+) VOLTAGE?
YES
CHECK
IC901 PIN 3
WAVEFORM (SQUARE
WAVE COMES OUT?)
NO
TROUBLE IN
IC901
NO
TROUBLE IN
D923, D922,
D924, D925, D927
YES
CHECK
D923, D922,
D924, D925, D927
VOLTAGE?
YES
TROUBLE IN
IC903
- 19 -
2. NO CHARACTER
NO CHARACTER
CHECK
IC302 PIN 3, 8, 12 (12V),
PIN 17 (5V)?
NO
TROUBLE IN
P302, P303
5V, 12V LINE
YES
CHECK
IC302 PIN 2, 6, 11 ?
NO
TROUBLE IN
PC SIGNAL,
SIGNAL CABLE
NO
TROUBLE IN
IC302
NO
TROUBLE IN
IC303
YES
CHECK
IC302 PIN 29, 32, 35 ?
YES
CHECK
R, G, B CATHODE
VOLTAGE?
YES
TROUBLE IN
CDT SOCKET
- 20 -
3. NO RASTER
NO VIDEO
(POWER INDICATOR
GREEN or ORANGE)
CHECK
POWER INDICATOR
GREEN or ORANGE ?
ORANGE
TROUBLE IN
D-SUB & 5-BNC
SIGNAL CABLE
GREEN
CHECK
SCREEN CONTROL
KNOB OF FBT
MIN.
(Counter-clockwise)
ROTATE SCREEN
CONTROL KNOB TO
CLOCKWISE
OK
CHECK
VOLTAGE AT
D924 CATHODE (190V)
D925 CATHODE (80V)
IC911 OUT (12V)
IC960 CATHODE
(6.3V)?
NO
TROUBLE IN PRIMARY
CIRCUIT OF T901, T902
NO
TROUBLE IN
SECONDARY CIRCUIT
OF T901, T902
YES
CHECK
IC201(MICOM) PIN 5
(5V), IC701 PIN 16
(12V)?
YES
TROUBLE IN
IC201 (MICOM),
IC701 (T/BASE), TDA4856
- 21 -
4. NO VERTICAL DEFLECTION
NO V-DEFLECTION
(ONE HORIZONTAL LINE)
CHECK
IC601 PIN 2 (15V) ?
NO
TROUBLE IN
T901 PIN 18
NO
TROUBLE IN
T901 PIN 17
NO
TROUBLE IN
IC701
YES
CHECK
IC601 PIN 4
(-12V)?
YES
CHECK
IC701 PIN 12
(SAWTOOTH WAVE)?
YES
TROUBLE IN
IC601, VERTICAL
OUTPUT CIRCUIT
- 22 -
5. TROUBLE IN DPM
STAND-BY/SUSPEND/
OFF MODE FAILURE
CHECK
IC201 (MICOM)
PIN 42, 1 (H/V INPUT)
SIGNAL?
CHECK PC,
(PC IS NOT GOING INTO
DPM MODE)
NO H / V SYNC SIGNAL
INPUT H/V SYNC
CHECK
IC201 PIN 6, 7
WAVEFORM?
NO
TROUBLE IN
X201, IC201
NO
TROUBLE IN
IC201
NO
TROUBLE IN
Q903, IC913, D914
YES
CHECK
IC201 PIN 5
(5V, HIGH)?
YES
CHECK
D922 CATHODE
(15V) ?
YES
CHECK
B+ LINE
(12V, 15V, 80V,
5V) ?
TROUBLE IN
R938
NO
DPMS TABLE
TROUBLE IN
T901 or PC
Item
H / V SYNC
VIDEO
LED
NORMAL
ON / ON
NORMAL
GREEN
STAND-BY
OFF / ON
OFF(0V)
ORANGE
SUSPEND
ON / OFF
OFF(0V)
ORANGE
OFF
OFF / OFF
OFF(0V)
ORANGE
Mode
- 23 -
6. NO DEGAUSSING
NO DEGAUSSING
CHECK
IC201 PIN 10
(5V)?
(
BUTTON MUST BE PRESSED.)
NO
TROUBLE IN
IC201 (MICOM)
NO
TROUBLE IN
Q271
NO
TROUBLE IN
P903, P904
NO
TROUBLE IN
RL901
YES
CHECK
Q271 COLLECTOR
VOLTAGE
(0.5V)?
YES
CHECK
P903, P904?
YES
CHECK
RL901?
YES
TROUBLE IN
TH901,
DEGAUSSING COIL
- 24 -
7. NO TILT (ROTATION )
NO TILT (ROTATION)
CHECK
IC303 PIN 7 VOLTAGE
(5V) ?
NO
TROUBLE IN
P303
YES
CHECK
Q315 BASE?
(0~5V)
NO
TROUBLE IN
IC201
NO
TROUBLE IN
Q309, Q312, Q313
YES
CHECK
P304 PIN 1 ?
YES
TROUBLE IN P304,
TILT COIL CONNECTOR,
TILT COIL
- 25 -
8. TROUBLE IN OSD
NO OSD
CHECK
IC301 PIN 9
(5V) ?
NO
TROUBLE IN
P302, D927
NO
TROUBLE IN
Q301, P302
NO
TROUBLE IN
P302
NO
TROUBLE IN
IC301, IC201
YES
CHECK
IC301 PIN 5
(NEGATIVE H-PULSE
COMES IN ?)
YES
CHECK
IC301 PIN 10
(NEGATIVE V-PULSE
COMES IN?)
YES
CHECK
IC301 PIN 13, 14, 15
(IS THERE ANY SIGNAL
WHEN OPERATING FRONT
CONTROL ?)
YES
TROUBLE IN
IC302
- 26 -
ADJUSTMENT
3. Adjustment for Factory Mode (Preset Mode).
GENERAL INFORMATION
1) Display cross hatch pattern at Mode 5.
2) Run alignment program for Flatron 995FT, FB995C
on the IBM compatible PC.
3) EEPROM →MODE CLEAR→Y(Yes) command.
<Caution> Do not run this procedure unless the
EEPROM is changed. All data in EEPROM (mode data
and color data)will be erased.
4) COMMAND →PRESET START→Y(Yes) command.
5) Adjust tilt as arrow keys to be the best condition.
6) DIST. ADJ. → BALANCE command.
7) Adjust balance of pin balance, key balance as arrow
keys to be the best condition.
8) DIST. ADJ. → BALANCE command.
9) Adjust parallelogram as arrow keys to be the best
condition.
10) DIST. ADJ. → FOS 1. ADJ command.
11) Adjust H-SIZE as arrow keys to 350±2mm.
12) Adjust H-POSITION as arrow keys to center of the
screen.
13) Adjust V-SIZE as arrow keys to 262±1mm.
14) Adjust V-POSITION as arrow keys to center of the
screen.
15) DIST. ADJ. → FOS 2. ADJ command.
16) Adjust S-PCC (Side-Pincushion) as arrow keys to
be the best condition.
17) Adjust TRAPEZOID as arrow keys to be the best
condition.
18) Display from Mode 1 to Mode 4 and repeat above
from number 10) to 17).
19) PRESET EXIT → Y (Yes) command.
All adjustment are thoroughly checked and corrected
when the monitor leaves the factory, but sometimes
several adjustments may be required.
Adjustment should be following procedure and after
warming up for a minimum of 30 minutes.
• Alignment appliances and tools.
- IBM compatible PC.
- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.or equivalent)
- EPROM or EEPROM with saved each mode data.
- Alignment Adaptor and Software.
- Digital Voltmeter.
- White Balance Meter.
- Luminance Meter.
- High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSING
The degaussing coil is mounted around the CDT so that
automatic degaussing when turn on the monitor. But a
monitor is moved or faced in a different direction, become
poor color purity cause of CDT magnetized, then press
(DEGAUSSING) on the OSD menu.
ADJUSTMENT PROCEDURE & METHOD
- Install the cable for adjustment such as Figure 1 and run
the alignment program on the DOS for IBM compatible PC.
1. Adjustment for B+ Voltage.
1) Display cross hatch pattern at Mode 4.
2) Adjust C951 (+) voltage to 190±0.5V with VR901.
4. Adjustment for White Balance and Luminance.
2. Adjustment for High-Voltage.
1) Set the White Balance Meter.
2) Press the (DEGAUSSING) on the OSD menu for
demagnetization of the CDT.
3) Display color 0,0 pattern at Mode 4.
4) Set Brightness and Contrast to max position.
5) COLOR ADJ. → BIAS ADJ. command of the
alignment program.
6) Check whether blue color or not at R-BIAS and GBIAS to min position and B-BIAS to 150 (decimal)
position at Sub-Brightness to 120 (decimal). If it's
not blue color, the monitor must repair.
1) Display cross hatch pattern at Mode 4.
2) Adjust CDT Anode voltage to 27kV±500V with
VR1001.
- 17 -
7) Adjust Screen control on the FBT to 0.1±0.02FL of
the raster luminance.
8) Adjust B-BIAS to 135 (decimal) and Sub-Brightness
to 120 (decimal).
9) Adjust R-BIAS and G-BIAS command to x=0.283±
0.006 and y=0.298 ±0.006 on the White Balance
Meter with PC arrow keys.
10) Adjust SUB-Brightness command to 0.5±0.1FL of
the raster luminance.
11) Display color 15,0 box pattern (70x70mm) at Mode 4.
12) DRIVE ADJ command.
13) Set B-DRIVE to 150 (decimal) at DRIVE of the
alignment program.
14) Adjust R-DRIVE and G-DRIVE command to white
balance x=0.283±0.003 and y=0.298±0.003 on the
White Balance Meter with PC arrow keys.
15) Adjust SUB-CONTRAST command to 40±1FL of
the raster luminance.
16) Display color 15,0 full white patten at Mode 4.
17) COLOR ADJ. → LUMINANCE → ABL command.
18) Adjust ABL to 32±1FL of the luminance.
19) Exit from the program.
5. Adjustment for Focus.
1) Display H character in full screen at Mode 4.
2) Adjust two Focus control on the FBT so that focus
should be the best condition.
A
IBM
Compatible PC
VIDEO
SIGNAL
GENERATOR
9
11
6
1
6
1
5
C
PARALLEL PORT
13
EL
LL
5V
RA
C
1
25
OFF
14
ON
F
PA
Power inlet (required)
5V
R
220
WE
VG
CS
T
MO
NI
TO
R
B
ON
4.7K
OFF
74LS06
E ST Switch
B
F V-Sync On/Off Switch
(Switch must be ON.)
Figure 1. Cable Connection
- 18 -
4.7K
4.7K
5V
E
YN
A
PO
S
Power Select Switch
(110V/220V)
Power LED
V-S
Control Line
RS
23
No
2C
tu
se
d
15
10
5
74LS06
DISASSEMBLY
1. TILT/SWIVEL REMOVAL
1) Set the monitor face downward.
2) Remove screw (a).
3) Pressing the latch (b), carefully remove
the Tilt/Swivel by pulling it upward.
(b)
(a)
2. BACK COVER REMOVAL
1) Remove two screw covers (a).
(b)
2) Remove four screws (b) from the Back Cover.
3) Remove the Signal Cap (c).
4) Slide the Back Cover away from the Front
Cabinet of the monitor.
(a)
(b)
(c)
(a)
3. TOP SHIELD REMOVAL
1) Remove four screws (a).
2) Remove four screws (b).
3) Remove two screws (c).
4) Remove three screws (d).
5) Slide the Top Shield away from the monitor.
(a)
(a)
(c)
(d)
(b)
(c)
(d)
(d)
(b)
(a)
(a)
(b)
(b)
- 11 -
4. TOTAL CHASSIS ASSEMBLY REMOVAL
1) Disconnect P903, P904 (Degaussing pin),
P704 (DY pin), Tilt pin, P610,P611 (Purity
pin) , P612(Convergence H/V), CDT Earth
Pin from the Main PCB.
2) Disconnect P306 (GND Wire) from the
Video PCB.
3) Carefully separate the CDT Board
Assembly from the CDT neck.
4) Discharge the remaining static
electricity by shorting between
the Anode Cap and the CDT ground.
5) Disconnect the Anode Cap
from the CDT.
6) Remove three screws (a).
7) Remove two screws (b).
8) Remove the Total Chassis Assembly
from the Cabinet.
Anode Cap
Purity
Convergence
P301
P319
P302P306
P303
Degauss
Tilt
CDT Earth
DY
P704
Purity
(a)
(a)
P704
P903
P612
(CONV H/V)
P404
P904
P403
P610
P401
PFC Only
P611
P402
(b)
Control PCB
(P101)
(a)
(b)
5. VIDEO PCB ASSEMBLY & CONTROL PCB ASSEMBLY REMOVAL
1) Disconnect P301, P302, P303, P306, P319 from the Video PCB.
2) Remove two screws (a).
3) Remove the Video PCB Assembly from the main total Assembly.
4) Remove two screws (b).
5) Disconnect P402 from the Main PCB.
P301
P319
P302
(a)
P306
P303
(a)
P404
P403
P401
P402
(b)
P101
(b)
- 12 -
6. REAR SHIELD ASSEMBLY REMOVAL
1) Remove two screws (a).
2) Remove five screws (b).
3) Disconnect P801-P802.
4) Remove the Rear Shield from the Main PCB Board.
(a)
(a)
(b)
(b)
(b)
P802
(b)
P801
(b)
7. MAIN BOARD ASS’Y REMOVAL
1) Remove seven screws (a).
2) Remove screw (b).
3) Remove screw (c).
4) Remove two screws (d).
5) Remove the Main Bracket and
the Bottom Shield.
(a)
(a)
(b)
(a)
(a)
(a)
(a)
(a)
(c)
(d)
(d)
- 13 -
CONTROL LOCATIONS
9
8
7
6
4
3
2
5
1
No.
Ref. No.
1
SW131
2
No.
Ref. No.
Control Function
POWER SWITCH
6
SW132
OSD SELECT/ADJUSTMENT (LEFT)
SW133
SET BUTTON
7
SW136
3
SW137
OSD SELECT/ADJUSTMENT (RIGHT)
8
VR901
OSD BUTTON
B + ADJUSTMENT
4
SW134
OSD SELECT/ADJUSTMENT (UP)
9
VR1001
HIGH-VOLTAGE ADJUSTMENT
5
SW135
OSD SELECT/ADJUSTMENT (DOWN)
Control Function
-9-
TIMING CHART
VIDEO
C
B
D
E
SYNC
F
A
FACTORY PRESET MODE
MODE
MARK
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
—
+
+
+
+
43.269
53.674
68.677
91.146
93.750
H
Sync Polarity
O
Frequency
kHz
Total Period
µs
A
23.112
18.631
14.561
10.971
10.666
Z
Video Active Time
µs
B
17.778
14.222
10.836
8.127
7.901
O
Blanking Time
µs
C
5.334
4.409
3.725
2.844
2.765
Front Porch
µs
D
1.556
0.569
0.508
0.406
0.316
A
Sync Duration
µs
E
1.556
1.138
1.016
1.016
0.948
L
Back Porch
µs
F
2.222
2.702
2.201
1.422
1.501
—
+
+
+
+
85.008
85.061
84.997
85.024
75.000
R
I
N
T
Sync Polarity
V
Frequency
Hz
R
Total Period
ms
A
11.763
11.756
11.765
11.762
13.333
T
Video Active Time
ms
B
11.093
11.178
11.183
11.235
12.800
Blanking Time
ms
C
0.670
0.578
0.582
0.527
0.533
A
Front Porch
ms
D
0.023
0.019
0.015
0.011
0.011
L
Sync Duration
ms
E
0.069
0.056
0.044
0.033
0.032
Back Porch
ms
F
0.578
0.503
0.523
0.483
0.490
Resolution
640
x
480
85Hz
800
x
600
85Hz
1024
x
768
85Hz
1280
x
1024
85Hz
1600
x
1200
75Hz
Recall
Yes
Yes
Yes
Yes
Yes
E
I
C
-4-
EXPLODED VIEW
17
19
EXPLODED VIEW PARTS LIST
18
21
3
4
A
20
21
5
6
8
9
2
7
B
10-1
10
Ref. No.
Part No.
1
3091TKC050A
CABINET ASSY
2
2423GG3E41D
CDT SET, M46QDG423X 01NPLD
3
339-002J
4
4951TKS041B
METAL ASSY, FRAME
5
6174T11002B
FBT(FLY BACK TRANSFORMER), Y268068(HFL1127RD)
6
6871TST167A
PWB(PCB), ASS’Y, SUB FB995C XKGU H/V CONTROL TOTAL
7
6200TJB004A
FILTER(CIRC), EMI 03ME3G(3) DELTA
8
4950TKK245A
METAL RAER(FB995C)
9
6871TUT006A
PWB(PCB) ASSY, SUB FB995C USB TOTAL
10
4951TKS043A
METAL ASSY FRAME (FB915B)
10-1
4810TKM027E
BRACKET FB915B MAIN (“D”-CORE)
11
332-102E
12
4950TKK117A
METAL, FIX HEAT SINK
13
4951TKS042A
METAL ASSY, SHIELD BOTTOM
14
6871TPT104A
PWB(PCB) ASSY, POWER FB995C XPVU (FB995C-UP); EUROPE ONLY(PFC)
15
6871TCH085A
PWB(PCB) ASSY, COMPOSITE FB995C CONTROL BRAND CA-** HAND
16
4810TKV012A
BRACKET FB915 VOLUME
17
4815TKT009A
SHIELD ASSY, TOP
3809TKC021C
BACK COVER ASSY, FB995C (3808TKC022A) B-CORE (FB995C-UA)
3809TKC021H
BACK COVER ASSY, FB995C C022 "B"CORE,PFC (FB995C-UP)
22
Description
SCREW ASSY, PHP+5x25(FZMW1)+GW18
SCREW, PTP+4x16(MSWR/FZMY)
18
11
14
19
332-122B
SCREW, TP1+M4x16(FZMY1)
20
3550TKK141A
COVER FB995C PIECE REAR
21
3550TKK084A
COVER FB915B SCREW
22
3043TKK048C
TILT SWIVEL ASSY
23
6866TDU002D
SIGNAL CABLE, UL20276SB10P+2C AWG#30 DT 1870MM
A
6871TVT165A
PWB(PCB) ASSY, VIDEO FB995C XKGU BRAND CA-** TOTAL
6871TMT168C
PWB(PCB) ASSY,MAIN FB995C XLVU BRAND CA-81 TOTAL (FB995C-UA)
6871TMT168D
PWB(PCB) ASSY,MAIN FB995C XPVU BRAND CA-81 TOTAL(FB995C-UP)
6871TCT085A
PWB(PCB) ASSY, COMPOSITE FB995C CONTROL BRAND CA-** TOTAL
3313T19022C
MAIN TOTAL ASSY, FB995C XLVU BRAND CA-81 (FB995C-UA)
3313T19022D
MAIN TOTAL ASSY, FB995C BRAND CA-81 (FB995C-UP)
16
D
15
12
OS
D
SE
T
B
C
C
1
D
23
13