10mm Ultra-Thin SMT DIP Rotaries Series FR02 Distinctive Characteristics Slim .150” (3.8mm) body has the lowest profile in the industry and allows close stacking of PC boards. Highly visible legends and screwdriver actuator with arrow position indication provide trouble-free code setting. Detent mechanism gives crisp, positive action for accurate switch setting. Use of heat resistant resin allows infrared convection reflow soldering. Gull-winged terminals ensure mechanical stability during soldering and simplify solder joint inspection. Cam activated movable contact and gold contacts assure contact reliability and continuity. Tape-reel packaging meets EIA-481-2 Standard. Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08 10mm Ultra-Thin SMT DIP Rotaries Series FR02 General Specifications Electrical Capacity (Resistive Load) Switching Rating: 100mA @ 5V DC Nonswitching Rating: 100mA @ 50V DC Other Ratings Contact Resistance: 100 milliohms maximum for circuit; 30 milliohms maximum for contact point Insulation Resistance: 1,000 megohms minimum @ 250V DC Dielectric Strength: 250V AC minimum for 1 minute minimum Mechanical Life: 10,000 detent operations minimum Electrical Life: 10,000 detent operations minimum Notes: A detent operation is one actuator position operation or stepping. A cycle is one 360° rotation. 10,000 detent operations equal 625 cycles for hexadecimal devices or 1,000 cycles for decimal devices. Nominal Operating Torque: 0.008Nm for decimal devices; 0.01Nm for hexadecimal devices Contact Timing: Shorting (Avoid possible false signal by turning off power before switching.) Materials & Finishes Actuator: Housing & Base: Leaf Spring: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Stainless steel Copper alloy with gold plating Phosphor bronze with gold plating Phosphor bronze with gold plating –25°C through +85°C (–13°F through +185°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 5 minutes; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Processing Soldering: Cleaning: Standards & Certifications Flammability Standards: UL Recognition or CSA Certification: Reflow Soldering Recommended. See Profile A in Supplement section. Note: During Reflow Soldering process, set the switch to the following position: FR02FR10P, FR02FR16P: 0 position; FR02FC10P: 7 position; FR02FC16P: F position Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 rated actuator, housing, & base The FR Series rotaries have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08 Series FR02 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH ORDERING EXAMPLE FR 02 F R MOUNTING 02 10 CIRCUITS SMT S TERMINALS R Real Coded (Orange Actuator) C Complement Coded (Yellow Actuator) P ACTUATORS F P Gull Wing for Upright Mount POSITIONS Screwdriver Actuated 10 Decimal 16 Hexadecimal PACKAGING S Stick-Tube 50 Pieces/Stick R Tape-Reel 500 Pieces/Reel DESCRIPTION FOR TYPICAL ORDERING EXAMPLE FR02FR10P-S Screwdriver Actuated Decimal Actuator Positions Real Coded Packaged in Stick-Tube Gull Wing Terminals for Upright Mount ACTUATORS F Screwdriver Actuated Actuators are fully rotational either clockwise or counterclockwise. Actuator Colors:Orange for real coded devices; Yellow for complement coded devices. Adjusted with a flat tipped screwdriver TRUTH TABLES (CIRCUITS & POSITIONS) Actuator Position x = ON Terminal No. (Output) 10 Decimal 16 Hexadecimal 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 A B C D E F 1 R Real Coded Model Number: FR02FR 2 4 8 C Complement Coded Model Number: FR02FC 1 2 4 8 Terminal numbers are actually on the switch. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 02-08 Series FR02 10mm Ultra-Thin SMT DIP Rotaries TYPICAL SWITCH DIMENSIONS P Upright • Screwdriver Actuated CL (0.2) .008 BCD 78 (13.0) .512 456 (3.8) Dia .150 (10.0) .394 4 2 (2.54) Typ .100 (1.27) Typ .050 1 1 2 4 8 (10.5) .413 C C (0.2) Typ .008 (10.0) .394 Decimal FR02FC10P 8 89 67 A (3.8) Dia .150 (10.0) .394 01 EF 2 3 45 23 (10.0) .394 (0.2) .008 901 (2.54) Typ .100 (0.1) Typ .004 (0.5) Typ .020 (3.9) .154 (1.0) Typ .039 (1.75) Typ .069 Hexadecimal PACKAGING S Stick-Tube Each stick-tube contains 50 switches. Switches must be ordered in 50-piece increments. (16.4) .646 (16.0) .630 R (540.0) 21.260 Tape-Reel Switches must be ordered in 500-piece increments. This packaging meets EIA-481-2 Standard. Each tape-reel of 550 pockets contains 500 switches. Minimum Leader Length: 15.748” (400mm) Minimum Trailer Length: 6.299” (160mm) (1.75) .069 (6.5) R .256 (80.0) Dia 3.150 (1.2) Typ .047 (10.3) Typ .406 (1.5) Dia Typ .059 (4.1) .161 (4.6) .181 3ϒMax (11.5) .453 901 78 (24.0) .945 (10.0) .394 456 Overall Dia (330.0) 13.0 (16.0) Typ .630 23 (10.5) Typ .413 (2.0) Typ .079 (2.0) Typ .079 (4.0) Typ .157 (24.4) .961 (30.4) Max 1.197 Direction of Feed NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com (0.4) .016 (2.1) Typ .083 02-08