Toggles Series HB Rockers General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Tactiles Subminiature Pushbuttons Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: 0.1A maximum @ 30V AC/DC Materials & Finishes Housing: Base: Movable Contact: Stationary Contacts: Common Terminal: End Terminals: Lamp Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: 50 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum 50,000 operations minimum 3.43N Nonshorting (break before make) Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm) Glass fiber reinforced polyamide Glass fiber reinforced polyamide Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating Phosphor bronze with silver plating –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Mounting Torque: 0.49Nm (4.34 lb • in) maximum for round mounting nut Cap Installation Force: 9.8N (2.2 lbf) maximum downward force on cap Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Standards & Certifications UL: File No. E44145 All models recognized at 0.1A @ 30V AC/DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. Supplement Accessories Indicators Touch Tilt Installation D12 www.nkk.com Toggles Series HB Subminiature Pushbuttons Rockers Distinctive Characteristics Choice of super bright LEDs in white, green, and blue in addition to bright red, amber, and green LEDs. Compact front panel design with 9mm square or round bezel options. D Keylocks Rear panel threaded mounting. Behind panel depth of less than one inch. 8mm body diameter fits common size panel cutout. Programmable Illuminated PB Pushbuttons Full face and spot illumination available. Front panel relamping. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Rotaries Dual, sliding contacts with self-cleaning action provide contact stability, high reliability, and increased operating life. Slides Solder lug terminals have spacing of .100” (2.54mm) for choice of mounting. Tactiles Longer normally closed terminal facilitates wiring and soldering. Molded-in terminals lock out flux, dust, and other contaminants. Touch Tilt Matching indicators available. Supplement Accessories Indicators Actual Size www.nkk.com D13 Series HB Toggles Subminiature Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 5 1 SPDT S K W01 Shapes Contacts & Terminals S Square C Round Silver Contacts and W01 Solder Lug Terminals* 0.1A @ 30V AC/DC 6G JB D Housing Circuits 5 ON K (ON) Black only ( ) = Momentary 6 ON ON Alternate Action with Latchdown * Wire harness & cable assemblies offered only in Americas Cap Types & Colors Bright LED Cap: Lens/Diffuser Color 5C Red 5D Amber 5F Green 6B White 6F Green 6G Blue No Nonilluminated Code Tilt Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Touch AB Black Cap/White Window for Spot Illuminated (Square only) CB Red/White DB Amber/White FB Green/White JB Clear/White LED Cap: Lens/Diffuser Color JB Nonilluminated IMPORTANT: Tactiles LEDs Super Bright Slides Rotaries 1 Pole Keylocks Programmable Illuminated PB Pushbuttons Rockers HB Clear/White Nonilluminated Cap Colors A Black (Square Only) B White C Red E Yellow F Green G Blue DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators HB15SKW01-6G-JB Blue, Super Bright LED White Cap Accessories Square Shape Black Housing SPDT ON-(ON) Circuit Supplement Silver Contacts & Solder Lug Terminals; rated 0.1A @ 30V AC/DC D14 www.nkk.com Series HB Toggles Subminiature Pushbuttons POLES & CIRCUITS SP HB15 *HB16 Normal Down Normal Down ON ON (ON) ON 1-3 1-2 Rockers Model Throw & Switch/Lamp Schematics Notes: Switch is marked with NO, NC, C, L. LED circuit is isolated and requires external power source. SPDT Pushbuttons Pole Connected Terminals 1 (COM) (+) 3 (-) 2 * When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel. D SHAPES & PANEL CUTOUT C .354” (9.0mm) Square .354” (9.0mm) Round Keylocks S Programmable Illuminated PB Plunger Position ( ) = Momentary Rotaries The bezel is an integral part of the switch body. The bezel is an integral part of the switch body. Slides Panel Cutout & Mounting (8.0) Dia .315 Overtightening the mounting nut AT073 may damage the switch housing. Tactiles Recommended Panel Thickness: .020 ~ .197” (0.5 ~ 5.0mm) Tilt HOUSING Housing available in black only. Touch K Silver Contacts Power Level PCB Mounting (5.0) .197 (2.0) .079 (1.0) .039 (1.8) .071 Thk = (0.3) .012 Accessories Solder Lug 0.1A maximum @ 30V AC/DC Solder lug terminals are spaced .100” x .200” (2.54mm x 5.08mm). This enables PCB mounting which can be accomplished by elongating PC board holes to .080” (2.03mm). www.nkk.com Supplement W01 Indicators CONTACT MATERIALS, RATINGS, & TERMINALS D15 Series HB Toggles Subminiature Pushbuttons LED COLORS & SPECIFICATIONS Rockers The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Single element LED is colored in OFF state. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Bright AT633 D AT630F Green 5F 6B 6F 6G Color Red Amber Green White Green Blue Unit Forward Peak Current I FM 30 30 25 30 30 30 mA Continuous Forward Current IF 20 20 20 20 20 20 mA Forward Voltage VF 1.85 2.0 2.2 3.6 3.5 3.6 V Reverse Peak Voltage VRM 5 5 5 5 5 5 V Current Reduction Rate Above 25°C ∆I F 0.40 0.42 0.38 0.50 0.50 0.50 mA/°C No Code (-) Ambient Temperature Range T-1 Bi-pin –25° ~ +50°C –25° ~ +50°C No Lamp CAP TYPES & COLORS Color Codes: A Black B White AB CB Black Cap with Translucent White Window for LED Display Amber/White FB Green/White D Amber E Yellow F Green AT4166 Square AT4052 Spot Illuminated AT4167 Round (7.4) Sq .291 G Blue (7.4) Sq .291 Square only Material: Polycarbonate Finish: Matte Red/White DB Tilt C Red Colored Cap for Bright LEDs Cap Colors Available: Lens/Diffuser Colors Available: Tactiles Super Bright 5D (+) AT629B White ELECTROSTATIC SENSITIVE DEVICES 5C Super Bright AT624G Blue Bright ATTENTION Note for Super Bright: (4.8) .189 Translucent White Diffuser (4.8) .189 Colored LED AT633 Finish: Glossy Transparent Clear Lens White Cap for Bright & Super Bright LEDs Supplement Accessories Indicators Touch JB Clear Lens/ White Diffuser AT4031 Square (7.4) Sq .291 AT4032 Round (4.8) .189 Finish: Glossy Translucent White Diffuser (7.4) Dia .291 (4.5) .177 Material: Polycarbonate (1.2) .047 (3.0) .118 Transparent Colored Lens (4.5) .177 Material: Polycarbonate (1.8) .071 (4.6) .181 (7.4) Dia .291 (4.5) .177 (4.8) .189 J Clear (4.5) .177 Colored LEDs AT624, AT629, AT630, or AT633 (4.8) .189 Nonilluminated Caps Cap Colors Available: A B Black (Square Only) White Material: Polycarbonate D16 C E Red Yellow F G Green Blue Finish: Glossy www.nkk.com AT4035 Square (7.4) Sq .291 AT4036 Round (4.5) .177 (4.8) .189 (7.4) Dia .291 (4.5) .177 (4.8) .189 Series HB Toggles Subminiature Pushbuttons TYPICAL SWITCH DIMENSIONS Square (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 L(+) L(-) NO NC 1 (5.0) .197 (7.0) .276 (2.54) Typ .100 Latchdown Position HB15SKW01-5C-CB Single Pole (1.0) x (2.0) Typ .039 x .079 (0.3) Typ .012 L(+) L(-) NO NC (7.4) Dia .291 (9.0) Dia .354 (1.3) .051 (3.5) .138 (5.0) (0.5) .197 .020 (10.0) .394 (5.3) (15.5) .209 .610 COM (1.8) .071 (2.54) Typ .100 2 3 1 (5.0) .197 (7.0) .276 (2.54) Typ .100 Latchdown Position HB16CKW01-5C-CB Slides ASSEMBLY INSTRUCTIONS Cap Removal LED Polarity & Orientation in Lamp Socket Cap Replacement 1. Have cap in extended position (not latchdown) for alternate action models. For AT624, AT629, AT630: Insert the LED with the D flat opposite the black dot molded inside the switch lamp socket. For AT633: Insert the LED with the Black Dot on the terminal to the right. 1. Match the prongs on the cap base with the projections in the switch, at the same time aligning the spring clips on the cap with the indentations in the switch. Black Dot D Flat (+) AT624 AT629 AT630 (–) (+) (–) AT633 2. Press firmly in place. Indicators ATTENTION ELECTROSTATIC SENSITIVE DEVICES Cathode (–) Super Bright LEDs AT624, AT629, & AT630 are electrostatic sensitive. AT111 Lamping Tool AT110 Socket Wrench Lamping Tool AT111 may be used to remove and replace LED. Socket Wrench AT110 may be used to tighten the mounting nut. www.nkk.com Accessories Anode (+) Touch Top View of Switch Supplement 2. Use the grip slots on the sides of the cap and pull it out of the switch. Rotaries M8P0.75 Round Keylocks D Tactiles (1.3) .051 (3.5) .138 (0.5) (5.0) .020 .197 (10.0) .394 (15.5) (5.3) .610 .209 3 Tilt (7.4) Sq .291 (9.0) Sq .354 COM (1.8) .071 (2.54) Typ .100 2 Pushbuttons M8P0.75 Rockers Single Pole Programmable Illuminated PB D17