SHOULDER ELECTRONICS LIMITED SAW Components Data Sheet PRODUCT 产 品: SAW FILTER MODEL NO 型 号: HDF1220A2 SMD-7 PREPARED 编 制: CHECKED 审 核: APPROVED 批 准: DATE Http://www.shoulder.cn 日 期: 2007-01-25 Page: 1 SHOULDER ELECTRONICS LIMITED 1. SCOPE This specification shall cover the characteristics of SAW filter With F1220A2S7 used digital television 2. ELECTRICAL SPECIFICATION Dc voltage VDC> Operation temperature Storage temperature RF Power dissipation Electronic Characteristics 0V -40°C~+85°C -40°C~+85°C 0 dBm(source impedance 200Ω) 2-1.Typical frequency response Http://www.shoulder.cn Page: 2 SHOULDER ELECTRONICS LIMITED 2-2.Electrical characteristics Part number Nominal frequency Maximum insertion Loss 1215~1225MHz Lower 1.5dB Bandedge Upper 1.5dB Bandedge Stopband Rejection 500~1152MHz 1152~1190MHz 1250~1288MHz 1288~2000MHz Amplitude Ripple 1215~1225MH Group Delay Ripple 1215~1225MH Source Impedance Load Impedance min - typ 1220.0 max - unit MHz 1225 4.5 1209.5 1230.5 5.5 1215 - dB MHz MHz 55 30 30 55 60 55 55 50 - 0.5 1.5 30 200 200 - - dB dB ns Ω Ω 3. TEST CIRCUIT Http://www.shoulder.cn Page: 3 SHOULDER ELECTRONICS LIMITED 4. DIMENSION 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -45℃for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in table 1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in table 1. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in table 1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Http://www.shoulder.cn Page: 4 SHOULDER ELECTRONICS LIMITED Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. Http://www.shoulder.cn Page: 5 SHOULDER ELECTRONICS LIMITED 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F 12.00 5.50 ±0.30 ±0.10 E 1.75 ±0.10 Http://www.shoulder.cn P0 P1 P2 4.00 4.00 2.00 ±0.10 ±0.10 ±0.10 D0 Ø1.50 Page: 6 D1 t1 t2 A B Ø1.5 0.31 1.30 3.4 3.4 ±0.25 ±0.05 ±0.10 MAX. MAX SHOULDER ELECTRONICS LIMITED [Figure 2] [Unit:mm] A B C D E W t r Ø330 Ø100 Ø13 Ø21 2 13 3 1.0 ±1.0 ±0.5 ±0.5 ±0.8 ±0.5 ±0.3 max. max. Http://www.shoulder.cn Page: 7 SHOULDER ELECTRONICS LIMITED