ULTRAFAST RECOVERY RECTIFIER DIODE 1N5806D2A / 1N5806D2B • Hermetic Ceramic Package Designed as a DropIn Replacement for D-5A MELF Package • Designed For High Rel Applications • Screening Options Available ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise stated) VRRM VRMS Vdc IO IFSM TJ Tstg Maximum Reverse Repetitive Peak Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Rectified Current Io2 = TA +55°C (1) Derate above TA 55°C Non Repetitive Forward Surge Current (2) Junction Temperature Range Storage Temperature Range 150V 105V 150V 1.0A 8.33mA/°C 35A -65 to +175°C -65 to +175°C T HERMAL PROPERTIES Symbols Parameters RθJSP(IN) Thermal Resistance, Junction To Solder Pads TSP =25°C RθJA(PCB) Thermal Resistance, Junction To Ambient (3) Max. Units 34 °C/W 150 °C/W Notes Notes (1) IO2 is rated at 1.0A @ TA = 55°C for PC boards where thermal resistance from mounting point to ambient is sufficiently controlled where TJ(Max) does not exceed 175°C; This equates to RθJA(PCB) ≤ 154°C/W. (2) TA = 25°C @ IO=1.0A and VRWM for ten 8.3mS surges at 1 minute intervals. (3) PCB = FR4, 0.0625 Inch (1.59mm) thick, single layer, 1.0-Oz Cu, Pad Size, (0.067” x 0.105”)‡, (1.7mm x 2.76mm) ‡, horizontal in still air. ‡ Recommended solder pad layout dimensions for this device, as detailed within this datasheet for the D-5A device. Semelab Limited reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc Telephone +44 (0) 1455 556565 Email: [email protected] Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8318 Issue 2 Page 1 of 4 ULTRAFAST RECOVERY RECTIFIER DIODE 1N5806D2A / 1N5806D2B ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise stated) Symbols VF * Parameters Forward Voltage Test Conditions IFM = 1.0A Min Typ TA = 125°C TA = -65°C IFM = 2.5A * IR * VBR Reverse Current VR = 150V Breakdown Voltage IBR = 100µA TA = 125°C TA = -65°C DYNAMIC CHARACTERISTICS (TC = 25°C unless otherwise stated) trr Reverse Recovery Time IF = IRM = 0.5A, I(REC) = 0.05A di/dt = 65A/µs CJ Capacitance * Pulse Test: VR = 10V f = 1.0MHz, Vsig = 50mV Max 0.875 0.800 1.075 0.975 1.0 175 160 150 Units V µA V 25 ns 25 pF tp = 300us, Duty Cycle ≤ 2% Semelab plc Telephone +44 (0) 1455 556565 Email: [email protected] Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8318 Issue 2 Page 2 of 4 ULTRAFAST RECOVERY RECTIFIER DIODE 1N5806D2A / 1N5806D2B MECHANICAL DATA DLCC2 Variant A (D2A) PAD 1 PAD 2 ANODE CATHODE DIMENSION A B C D mm 5.00 ±0.10 2.61 ±0.10 1.08 ±0.10 1.76 ±0.10 Inches 0.197 ±0.004 0.103 ±0.004 0.043 ±0.004 0.069 ±0.004 DLCC2 Variant B (D2B) PAD 1 PAD 2 PAD 3 ANODE CATHODE LID CONTACT TO ANODE* DIMENSION A B C D mm 5.00 ±0.10 2.61 ±0.10 1.08 ±0.10 1.76 ±0.10 Inches 0.197 ±0.004 0.103 ±0.004 0.043 ±0.004 0.069 ±0.004 SOLDER PAD LAYOUT D-5A DLCC2/ D-5A MELF OVERLAY DIMENSION A B C mm 6.25 1.70 2.67 Inches 0.246 0.067 0.105 C A B * The additional contact provides a connection to the lid in the application. Connecting the metal lid to a known electrical potential stops deep dielectric discharge in space applications; see the Space Weather link www.semelab.co.uk/mil/lcc1_4 on the Semelab web site. Package variant to be specified at order. Other Package Outlines may be available – Contact Semelab Sales to Enquire Semelab plc Telephone +44 (0) 1455 556565 Email: [email protected] Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8318 Issue 2 Page 3 of 4 ULTRAFAST RECOVERY RECTIFIER DIODE 1N5806D2A / 1N5806D2B SCREENING OPTION ORDERING INFORMATION Space Level (JQRS/ESA) and High Reliability options are available in accordance with the High Reliability and Screening Options Handbook available for download from the from the TT electronics Semelab web site. Part numbers are built up from Type, Package Variant, and screening level. The part numbers are extended to include the additional options as shown below. ESA Quality Level Products are based on the testing procedures specified in the generic ESCC 5000 and in the corresponding part detail specifications. Type – See Electrical Stability Characteristics Table Package Variant – See Mechanical Data Screening Level – See Screening Options (ESA / JQRS) Additional Options: Semelabs QR216 and QR217 processing specifications (JQRS), in conjunction with the companies ISO 9001:2000 approval present a viable alternative to the American MILPRF-19500 space level processing. QR217 (Space Level Quality Conformance) is based on the quality conformance inspection requirements of MIL-PRF19500 groups A (table V), B (table VIa), C (table VII) and also ESA / ESCC 5000 (chart F4) lot validation tests. QR216 (Space Level Screening) is based on the screening requirements of MIL-PRF-19500 (table IV) and also ESA /ESCC 5000 (chart F3). JQRS parts are processed to the device data sheet and screened to QR216 with conformance testing to Q217 groups A and B in accordance with MIL-STD-750 methods and procedures. Additional conformance options are available, for example Pre-Cap Visual Inspection, Buy-Off Visit or Data Packs. These are chargeable and must be specified at the order stage (See Ordering Information). Minimum order quantities may apply. Alternative or additional customer specific conformance or screening requirements would be considered. Contact Semelab sales with enquires. MARKING DETAILS Parts can be laser marked with approximately 7 characters on two lines and always includes cathode identification. Typical marking would include part or specification number, week of seal or serial number subject to available space and legibility. Customer specific marking requirements can be arranged at the time of order. Example Marking: Customer Pre-Cap Visual Inspection Customer Buy-Off visit Data Pack Solderability Samples Scanning Electron Microscopy Radiography (X-ray) Total Dose Radiation Test .CVP .CVB .DA .SS .SEM .XRAY .RAD MIL-PRF-19500 (QR217) Group B charge Group B destructive mechanical samples Group C charge Group C destructive electrical samples Group C destructive mechanical samples .GRPB .GBDM (12 pieces) .GRPC .GCDE (12 pieces) .GCDM (6 pieces) ESA/ESCC Lot Validation Testing (subgroup 1) charge LVT1 destructive samples (environmental) LVT1 destructive samples (mechanical) Lot Validation Testing (subgroup 2) charge LVT2 endurance samples (electrical) Lot Validation Testing (subgroup 3) charge LVT3 destructive samples (mechanical) .LVT1 .L1DE (15 pieces) .L1DM (15 pieces) .LVT2 .L2D (15 pieces) .LVT3 .L3D (5 pieces) Additional Option Notes: 1) All ‘Additional Options’ are chargeable and must be specified at order stage. 2) When Group B,C or LVT is required, additional electrical and mechanical destructive samples must be ordered 3) All destructive samples are marked the same as other production parts unless otherwise requested. Example ordering information: The following example is for the 1N5806 part with package variant B, JQRS screening, additional Group C conformance testing and a Data pack. Part Numbers: 1N5806D2B-JQRS (Include quantity for flight parts) 1N5806D2B-JQRS.GRPC (chargeable conformance option) 1N5806D2B-JQRS.GCDE (charge for destructive parts) 1N5806D2B-JQRS.GCDM (charge for destructive parts) 1N5806D2B-JQRS.DA (charge for Data pack) Customers with any specific requirements (e.g. marking or screening) may be supplied with a similar alternative part number (there is maximum 20 character limit to part numbers). Contact Semelab sales with enquiries. High Reliability and Screening Options Handbook link: http://www.semelab.co.uk/pdf/misc/documents/hirel_and_screening_options.pdf Semelab plc Telephone +44 (0) 1455 556565 Email: [email protected] Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 8318 Issue 2 Page 4 of 4