HITTITE HMC701LP6CE

HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Features
• Fractional or Integer Modes
• Reference spurs: -90 dBc typ
• 8 GHz, 16-Bit RF N-Counter
• Auto and Triggered Sweeper Functions
• 24-Bit Step Size Resolution, 3 Hz typ
• Cycle Slip Prevention (CSP) for fast settling
• Ultra Low Phase Noise 6 GHz, 50 MHz Ref.
-103 / -110 dBc/Hz @ 20 kHz (Frac / Integer)
• Autotune support for external step tuned VCOs
• Reference Path Input: 200 MHz
• Auxiliary Clock Source
• 14-Bit Reference Path Divider
• 40 Lead 6x6mm SMT Package: 36mm²
• Multi-VCO Support
• Low Fractional Spurious
PLL - fractional-n synthesizer - SMT
11
11 - 2
Typical Applications
• Base Stations for Mobile Radio
(GSM, PCS, DCS, CDMA, WCDMA)
• CATV Equipment
• Wireless LANs, WiMax
• Automotive Radar
• Communications Test Equipment
• Phased-Array Systems
• FMCW Sensors
Functional Diagram
(Figure 1.)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
General Description
The HMC701LP6CE is a SiGe BiCMOS fractional-N frequency synthesizer. The synthesizer includes a 8GHz 16-bit
RF N-Divider, a 24-bit delta-sigma modulator, a very low noise digital phase frequency detector (PFD), and a precision
controlled charge pump. In addition the synthesizer supports an external step tuned VCO.
The fractional synthesizer features an advanced delta-sigma modulator design that allows ultra-fine frequency step
sizes. The synthesizer features the ability to alter both the phase-frequency detector (PFD) gain and the cycle slipping
characteristics of the PFD. This feature can reduce the time to arrive at the new frequency by 50% vs. conventional
PFDs. Ultra low in-close phase noise also allows wider loop bandwidths for faster frequency hopping.
The synthesizer contains a built-in linear sweeper function, which allows it to perform frequency chirps with a wide
variety of sweep times, polarities and dwells, all with an external or automatic sweep trigger.
Electrical Specifications, TA = +25°C
VCCHF = VCCPRS = RVDD = +3.3V
VPPCP = VCCOA = VDDPDR = VPPDRV = VDDPD = VDDPDV = +5V
DVDD = DVDDIO = DVDDQ = +3.3V
GNDDRV = GNDCP = GNDPD = GNDPDV = GNDPDR = 0V
Table 1. Electrical Specifications
Parameter
Conditions / Notes
Min
Typ
Max RF Input Frequency (3.3V)
8
9
Max RF Input Frequency (2.7 - 3.3V)
7
8
Max
Units
Prescaler Characteristics
Min RF Input Frequency
GHz
0.1
MHz
10
dBm
RF Input Power
-10
16-bit N-Divider Range (Integer)
32
65,535
35
65,531
16-bit N-Divider Range (Fractional)
Fraction Nominal Divide ratio varies
(-3 / +4) dynamically max
-6
GHz
REF Input Characteristics
Max Ref Input Frequency (pin XREFP)
180
200
MHz
Max Ref Input Frequency (pin XSIN)
200
220
MHz
60
MHz
Max Ref Frequency with AutoCal
Min Ref Input Frequency
100
kHz
Ref Input Voltage Range (pin XREFP)
AC Coupled
750
1000
3300
mVpp
Ref Input Power Range (pin XSIN)
50 Ω Source
-6
0
12
dBm
5
pF
Ref Input Capacitance
14-Bit R-Divider Range
1
11
PLL - fractional-n synthesizer - SMT
A General Purpose Output (GPO) bus supports the use of multiple VCOs. In addition the synthesizer has a number of
auxiliary clock generation modes that can be accessed via the GPO.
16,383
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 3
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 1. Electrical Specifications
(Continued)
Parameter
Conditions / Notes
Min
Typ
70
75
Max
Units
Phase Detector
Fractional Mode
Max Phase Detector Frequency
Min Phase Detector Frequency
MHz
100
kHz
Integer Mode
Max Phase Detector Frequency
110
150
Min Phase Detector Frequency
MHz
100
kHz
Charge Pump
PLL - fractional-n synthesizer - SMT
11
11 - 4
Max Output Current
4
mA
Min Output Current
125
µA
Charge Pump Gain Step Size (5-bits)
125
µA
Charge Pump Trim Step Size (3-bits)
14
µA
Charge Pump Offset Step Size (4-bits)
29
µA
-141
dBc/Hz
10 kHz
-149
dBc/Hz
100 kHz
-155
dBc/Hz
PFD / Charge Pump Noise (Integer)
6 GHz, 50 MHz Ref, Input referred
1 kHz
Less than 3 dB degradation typ. at
these limits
Compliance Voltage
-406 µA Offset
0.4
VPPCP-0.8
V
-406 µA Offset
0.8
VPPCP-0.4
V
Logic Inputs
VIH Input High Voltage
V
VDDIO-0.4
VIL Input Low Voltage
0.4
V
0.1
V
3.3
3.45
V
Logic Outputs
VIH Output High Voltage
V
VDDIO-0.1
VIL Output Low Voltage
Power Supply Voltages
VCC - Analog 3V Supplies
VCCPRS, RVDD, VCCHF
DVDD - Digital Internal Supply
DVDD, DVDDQ
3
3.3
3.45
V
DVDDIO
1.8
3.3
5.5
V
VCCOA, VPPCP, VPPDRV,
VDDPD, VDDPDV, VDDPDR
4.5
5.0
5.5
V
DVDDIO - Digital I/o Supply
Analog 5V Supplies
3
Power Supply Current (6 GHz Fractional Mode, 50 MHz PFD)
VCCOA, VPPCP, VPPDRV,
VDDPD, VDDPDV, VDDPDR
37
Analog +3.3V
VCCPRS, RVDD, VCCHF
71
mA
Digital +3.3V
DVDD, DVDDIO, DVDDQ
19
mA
Reg 01h = 0
Crystal not clocked
6
µA
Reg 01h = 0
Crystal clocked 100 MHz
20
Analog +5V
Power Down - Crystal Off
Power Down - Crystal On, 100 MHz
mA
200
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
µA
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 1. Electrical Specifications
(Continued)
Parameter
Conditions / Notes
Min
Typ
Max
Units
Temperature Sensor (3-bit)
Min Temperature
Readout: 000
-32
Max Temperature
Readout: 111
+82
°C
Temp Change / LSB
17.5
°C/LSB
Worst Case Absolute Temp Error
±10
°C
2
mA
700
mV
Current Consumption (when Enabled)
°C
Power on Reset
Min DVDD Voltage for No Reset
1.5
V
Closed Loop Phase Noise
6 GHz VCO, Integer, 50 MHz PFD
1 kHz offset
-98
dBc/Hz
6 GHz VCO, Integer, 50 MHz PFD
10 kHz offset
-108
dBc/Hz
6 GHz VCO, Integer, 50 MHz PFD
100 kHz offset
-110
dBc/Hz
1 kHz offset
-93
dBc/Hz
6 GHz VCO, Fractional, 50 MHz PFD
6 GHz VCO, Fractional, 50 MHz PFD
10 kHz offset
-103
dBc/Hz
6 GHz VCO, Fractional, 50 MHz PFD
100 kHz offset
-105
dBc/Hz
Closed Loop Phase Noise
Normalized to 1 Hz
Integer Mode
Measured with 50 MHz PFD
-227
dBc/Hz
Fractional Mode
Measured with 50 MHz PFD
-221
dBc/Hz
Table 2. Absolute Maximum Ratings
Parameter
Rating
RVDD, VCCHF, DVDD,
DVDDQ, VCCPRS
-0.3 to +3.6V
VCCOA, VPPCP, VPPDRV, VDDPD,
VDDPDV, VDDPDR, DVDDIO
-0.3 to +6V
Operating Temperature
-40 to +85 °C
Storage Temperature
-65 to +120 °C
Maximum Junction Temperature
+150 °C
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device. This
is a stress rating only; functional operation of the device
at these or any other conditions above those indicated in
the operational section of this specification is not implied.
Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Reflow Soldering
Peak Temperature
260 °C
Time at Peak Temperature
40 sec
ESD Sensitivity (HBM)
Class 1B
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Typical Reset Voltage on DVDD
11 - 5
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 3. Pin Description
PLL - fractional-n synthesizer - SMT
11
11 - 6
Pin No.
Pin Name
PIn Type
1
VCCPRS
Supply
Description
RF Prescaler Power Supply. Nominally +3.3V
2
VCCOA
Supply
ChargePump OpAmp Power Supply. Nominally +5V
3
VPPCP
Supply
Power Supply for Charge Pump. Nominally +5V
4
CP
Analog O/P
Charge Pump output
5
GNDCP
GND
Power Supply GND for Charge Pump
6
GNDDRV
GND
Charge Pump GND
7
VPPDRV
Supply
Power supply for Charge Pump, Nominally +5V
8
VDDPD
Supply
Power Supply for Phase Detectors, Nominally +5V
9
GNDPD
GND
10, 20, 21, 26
N/C
N/C
Power Supply GND for Phase Detector
11
VDDPDV
Supply
12
GNDPDV
GND
13
VDDPDR
Supply
14
GNDPDR
GND
15
XREFP
Analog I/P
16
RVDD
Supply
17
XSIN
Analog I/P
Sinusoidal Crystal reference input
18
REFCAP
Analog I/O
Reference Path bypass
19
RSTB
CMOS I/P
Reset Input (active low)
22
DVDD
Supply
Digital Power Supply, Nominally +3.3V
23
GPO1
DO
General Purpose Output 1 with Tristate
24
GPO2
DO
General Purpose Output 2 with Tristate
25
GPO3
DIO
General Purpose Input/Output with Tristate
may be configured for External Ramp trigger Input. See register REG 14h[5]
27
SEN
CMOS I/P
Main Serial port enable input
28
SDI
CMOS I/P
Main Serial port data input
Main Serial port clock input
No Connection
Power Supply for Phase Detector VCO Path, Nominally +5V
Power Supply GND for Phase Detector VCO Path
Power Supply for Phase Detector Ref Path, Nominally +5V
Power Supply GND for Phase Detector Ref Path
Square Wave Crystal Ref Input
Power Supply for Ref Path, Nominally +3.3V
29
SCK
CMOS I/P
30
VSLE
CMOS O/P
VCO Serial port enable output
31
VSDO
CMOS O/P
VCO Serial port data output
32
VSCK
CMOS O/P
VCO Serial port clock output
33
LD_SDO
CMOS O/P
Lock Detect or Main Serial Port Data Output
34
DVDDIO
Supply
Power Supply for digital I/O, matches external Digital Supply in 1.8V to 5.5V range
35
DVDD
Supply
Internal Digital Power Supply. Nominally 3.3V
36
DVDDQ
Supply
Power Supply Isolation pin. Nominally 3.3V, bypassed to GND, zero current.
37
VCOIP
RF I/P
Complementary Input to the RF Prescaler. If single ended input, this point must be
decoupled to the ground plane with a ceramic bypass capacitor, typically 100 pF
38
VCOIN
RF I/P
Input to the RF Prescaler. This signal input is ac-coupled to the external VCO
39
VCCHF
Supply
RF Section Power Supply. Nominally 3.3V
40
BIAS
Analog I/P
Decoupling Pin for RF section, nominally external 1nF bypassed to VCCHF
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Figure 2.
Figure 3.
Typical Phase Noise - Integer Mode
Typical Phase Noise - Fractional Mode
-90
-90
6 GHz Integer
-100
PHASE NOISE (dBc/Hz)
1 GHz Integer
-120
-130
-140
All Plots 50 MHz PFD
-150
-160
2 GHz Fractional
-110
-120
-130
All Plots 50 MHz PFD
-140
-150
-160
-170
1000
10
4
10
5
10
6
10
7
10
-170
1000
8
4
5
10
6
7
10
10
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 4.
Figure 5.
RF Divider Sensitivity
Frequency Sweep
8
10
10
11
6150
20
+85C
FRAC
INTEG
6100
0
FREQUENCY (MHz)
+25C
-40C
-10
-20
-40
6050
6000
5950
5900
-30
0
2000
4000
6000
FREQUENCY (MHz)
8000
5850
-2
10000
-1
0
1
2
TIME (ms)
Figure 6.
Cycle Slip Prevention: Frequency Hop
from 5200 MHz to 3950 MHz
5300
5100
FREQUENCY (MHz)
INPUT POWER (dBm)
10
4900
CSP OFF
4700
4500
CSP ON
4300
4100
3900
-10
0
10
20
30
40
50
60
70
TIME (μs)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
3
PLL - fractional-n synthesizer - SMT
PHASE NOISE (dBc/Hz)
-110
6 GHz Fractional
-100
2 GHz Integer
11 - 7
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Theory of Operation
The HMC701LP6CE synthesizer consists of the following functional blocks
1. Reference Path Input Buffers
2. Reference Path Divider
3. VCO Path Input Buffer
4. VCO Path Multi-Modulus Prescaler/Divider
5. Δ∑ Fractional Modulator
6. Phase Frequency Detector
7. Charge Pump
8. Main Serial Port
9. VCO Serial Port for Stepped VCO Support
10. Temperature Sensor
11. Power On Reset Circuit
12. VCO Autocalibration Subsystem
13. CW Sweeper Subsystem
14. Auxiliary Clock Generator
15. General Purpose Output (GPO) Bus
16. Multiple VCO Controller
Each of these blocks is described briefly in the following section.
PLL - fractional-n synthesizer - SMT
11
11 - 8
Reference Path
The full Reference Path block diagram is shown in Figure 7. The ultra low noise phase detector requires the best
possible reference signal. Since a given application may desire to use a square wave or a 50 Ohm sinusoidal
crystal source, HMC701LP6CE offers two input ports, each one optimized for the lowest possible noise for the
source type being used.
For absolute best low noise performance, the sine wave path should be used.
The user should use only one Ref path input, that is the input that matches their reference source type. Note the
input is defaulted to the square wave input on power up. Should the sine reference path be used, it is necessary
to enable the sine input, shut down the square wave input and set the mux (rfp_buf_sin_en=1, rfp_buf_sq_en=0,
rfp_buf_sin_sel=1, Table 12). The unused port should be left open.
The reference path supports input frequencies of up to 200 MHz typical, however the maximum frequency at
the phase detector (PFD) depends upon the mode of operation, worst case at +85°C, 70 MHz in fractional mode
and 110 MHz in integer mode. Hence reference inputs of greater than the PFD maximum frequency must use the
appropriate R divider setting. A further restriction exists. If the VCO auto calibration feature is used, the reference
input must not exceed 60 MHz.
Figure 7. Reference Sine Input Stages
The unused reference port is normally not connected.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Sine Reference Input
The crystal reference sine input stage is shown in Figure 8. This is the lowest noise reference path. This is a common
emitter single ended bipolar buffer. The XSIN input pin is DC coupled and has about 950 mV bias on it. Expected
input is a 0 dBm sinusoid from a 50 Ohm source. Normally the input should be AC coupled externally. The sine buffer
input impedance is dominated by a 25 Ohm shunt resistor in series with a 50 pF on chip cap. Should a lower input
impedance be needed, an external 50 Ohm shunt resistor can be used, DC isolated by an external bypass cap. The
sine input reference path phase noise floor is approximately equivalent to -159 dBc/Hz. For best performance care
should be taken to provide a crystal reference source with equivalent or better phase noise floor.
Figure 8. Ref Sine Input
Square Wave Reference Input
The square wave Ref Input stage is shown in Figure 9. The stage is designed to accept square wave inputs from CML
to CMOS levels. Slightly degraded phase noise performance may be obtained with quasi sine 1 Vpp inputs. It may be
necessary to attenuate very large CMOS levels if absolute best in close phase noise performance is required. Input
reference should have a noise floor better than -160 dBc/Hz to avoid degradation of the input reference path.
Figure 9. Square Wave Ref Input Stage
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
11
11 - 9
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Reference Path ’R’ Divider
The referenced path features a 14-bit divider (rfp_div_ratio, Reg03h<13:0> Table 14) and can divide input signals
at up to 200 MHz by numbers from 1 to 16,383. The selected input reference source may be divided or bypassed
(rfp_div_select), and applied to the phase detector reference input.
VCO Auto Tuning and Serial Port Clocks
The optional VCO Auto Tuning state machine and the VCO Serial Port clocks use the undivided selected external
reference signal, as determined by rfp_xref_sin_select Reg12h<6> (Table 29), and as shown in Figure 10.
Reference Path Test Features
PLL - fractional-n synthesizer - SMT
11
A fractional synthesizer is a complex combination of a low phase noise analog oscillator running in close proximity with
a nearly randomly modulated delta-sigma digital modulator.
Clean spur free operation of the synthesizer requires proper board layout of power and grounds. Spurious sources
are often difficult to identify and may be related to harmonics of the digital modulation which land near the operating
frequency of the VCO, or they may arise from repeating patterns in the digital modulation itself . The loop filter and the
fractional modulator are designed to suppress these fractional spurs, but it is sometimes the case that the isolation
of the spurious products comes from layout issues. The problem is how to identify the sources of spurious products
if they occur?
The reference path of the HMC701LP6CE features some interesting test options for clocking the digital portion of the
synthesizer which may provide for a better understanding of the source of reference spurs should they occur. See
Figure 10, Table 12 and Table 29 for more register details.
It is possible for example to set the synthesizer to integer mode of operation, where the digital harmonics normally
fall directly on the VCO frequency. We might chose for example to use the sine source (rfp_buf_sine_sel=1, div_
todig_en=0) to drive the reference divider. In such a case the delta sigma modulator is not normally used, however if
we wish to test the effects of the digital power supply isolation, we could input a 2nd reference source on the square
wave input, enable its buffer (rfp_buf_sq_en=1), and enable the 2nd crystal to clock the unused delta sigma modulator
(sqr_todig_en=1 and dsm_xref_sin_select=0). This would allow the square wave clock to be set independently of
the locked integer mode VCO, and hence measure the coupling of the digital to the sidebands of the VCO at various
frequencies. Such a test can help in identifying and debugging grounding and layout issues in the application circuit
related to the digital portion of the PCB should they occur. In general it is recommended to follow the suggested layout
closely to avoid any such problems.
Figure 10. Reference Path Block Diagram
11 - 10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
VCO Path
The RF path from the VCO to the phase detector, is referred to as the VCO path. The VCO path consists of an input
isolation buffer and a multi-modulus prescaler, or simply the N divider. The N divider is controlled by the fractional
modulator. This path operates with inputs directly from the external VCO.
RF Input Stage
Figure 11. RF Input Stage
RF Path ’N’ Divider
The main RF path divider is capable of average divide ratios between 65,531 and 36 in fractional mode, and 65,535
to 32 in integer mode. The reason for the difference between integer and fractional modes is that the fractional divider
actually divides by up to ±4 from the average divide number. Actual division ratios when used with a given VCO will
depend upon the reference frequency used and the desired output band.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
The synthesizer RF input stage routes the external VCO to the phase detector via a 16-bit fractional divider. The RF
input path is rated to operate nominally from 100 kHz to 8 GHz in fractional and 9 GHz in integer modes. The RF input
stage also provides isolation between the VCO and the prescaler. The RF input stage is a differential common emitter
stage, DC coupled for maximum flexibility. The input is protected by ESD diodes as shown in Figure 11. Normally the
RF input is AC coupled to a single ended external source. The RFINP buffer is well matched from a single ended
50 Ohm source above about 3.5 GHz, with the complimentary input grounded. If a better match is required at low
frequency a simple shunt 50 Ohm resistor can be used external to the package. If a differential external source is used
then the two input pins may be used for best performance.
11 - 11
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
General Purpose Output (GPO) Interface
The HMC701LP6CE features a 3-wire General Purpose Output (GPO) interface. GPO registers are described in
Reg1Bh Table 37. The GPO is a flexible interface that supports a number of different functions and real time waveform
access including:
PLL - fractional-n synthesizer - SMT
11
11 - 12
a. General Data Output from SPI register gpo_sel_0_
data (gpo_sel=0)
f. Mirror of VCO Serial Port Data, Clock, Latch Enable
(gposel=5)
b. Prescaler & reference path outputs (gpo_sel=1)
g. Δ∑ Modulator Phase Accumulator (gposel=6)
c. Lock Detect Windows (gpo_sel=2)
h. Auxiliary oscillators (gposel=7)
d. Anti-cycle Slip waveforms (gpo_sel=3)
i. Auto Calibration Busy Flag (gposel=8)
e. Internal synchronized frac strobe with clocks
(gposel=4)
k. Δ∑ Modulator Outputs (gposel=10)
j. Multiple VCO Control, Latch Enables (gposel=9)
General Data to GPO (gpo_sel=0)
Setting register gpo_sel=0 in Table 37 assigns the 3-bit data from register gpo_sel_0_data Reg1B<6:4> to the GPO
bus.
Prescaler and Reference Path Outputs (gpo_sel = 1)
Setting register gpo_sel=1 (Reg1B<3:0> Table 37) results in the input crystal being buffered out to GPO3 as shown in
Figure 12. This is useful for example to generate a copy of the input crystal signal to drive other circuits in the application,
while at the same time isolating the noisy circuits from the sensitive crystal output. Often only the synthesizer requires
very low phase noise from the crystal, hence it is desirable to isolate other circuits from the crystal itself and allow the
synthesizer sole use of the low phase noise crystal.
gpo_sel=1 also routes the 200 MHz 14-bit reference path divider to GP02 and the 16-bit 7 GHz VCO path prescaler
output to GP01. This option allows the synthesizer to function as a stand alone fractional or integer prescaler and
provides visibility into the prescaler and reference path timing for sensitive applications.
Figure 12. gpo_01 Outputs
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Lock Detect Windows (gpo_sel=2)
Setting register gpo_sel = 2 (Reg1Bh<3:0> Table 37) results in the lock detect window (Figure 21) and the phase
frequency detector UP and DN output control signals (Figure 24) to be routed to pins GPO1, GPO3 and GPO2
respectively. This option gives insight into the Lock Detection Process and could allow the synthesizer to be used with
an external charge pump.
Figure 13. gpo_02 Outputs
Anti-cycle Slip Waveforms (gpo_sel = 3)
Setting register gpo_sel=3 (Reg1Bh<3:0> Table 37) gives visibility into the anti-cycle slipping function of the PFD
as described in section Cycle Slip Prevention (CSP). Three waveforms, reference path freq > VCO path freq, vco
path freq > ref path freq, and a PFD strobe which holds the PFD at maximum gain, are routed to GPO3, GPO2, and
GPO1 respectively. These lines will be active during frequency pull-in and will indicate instantaneously which signal,
reference or vco path is greater in frequency. The PFD strobe gives insight into when the PFD is near maximum gain
at 2π. The PFD strobe will be active until the VCO pulls into lock.
Internal Synchronized Frac strobe with clocks (gpo_sel= 4)
Setting register gpo_sel=4 in (Reg1Bh<3:0> Table 37) gives visibility into the internally synchronized strobe that
is generated when commanding a frequency change by writing to the frac register. The internal strobe initiates the
update to the fractional modulator, and the VCO SPI transfer if applicable. The internal frac strobe, the ref path divider
output and the sine reference input are buffered out to GPO1,GPO2 and GPO3 respectively as shown in Figure 14. In
this mode, GPO1 may be used to trigger an external instrument = when doing frequency hopping tests for example.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
11
11 - 13
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
PLL - fractional-n synthesizer - SMT
11
11 - 14
Figure 14. gpo_04 Outputs
Mirror of VCO Port Data, Clock, Latch Enable (gpo_sel=5)
Setting register gpo_sel=5 (Reg1Bh <3:0> Table 37) mirrors the output of the VCO SP on the gpo pins.
Δ∑ Modulator Phase Accumulator (gpo_sel=6)
Setting register gpo_sel=6 (Reg1Bh<3:0> Table 37) assigns the three msb’s of the delta sigma modulator first
accumulator to GPO<3:1> , where GPO3 is the msb. This feature provides insight into the phase of the VCO.
Auxiliary Oscillators (gpo_sel=7)
Setting register gpo_sel=7 (Reg1Bh<3:0> Table 37) assigns an auxiliary clock, an internal ring oscillator, and the
internal sigma delta clock to GPO3, 2, 1 respectively. The control of the auxiliary clock is determined by Reg18h Table
34 and Reg19h Table 35. In general terms, this highly flexible clock source allows the selection of one of the various
VCO or crystal related clocks inside the synthesizer or the selection of a flexible unstabilized auxiliary ring oscillator
clock. Any of the sources may be routed out via gpo_sel=7. Additional Reg18h Table 34 clock controls allow the aux
clock to be delayed by a variable amount (auxclk_modesel Reg18h<3:2>), or to be divided down by even values from
2 to 14 (auxclk_divsel Reg18h<6:4>).
Auto Calibration Busy Flag (gpo_sel=8)
Setting register gpo_sel=8 (Reg1B<3:0> Table 37) assigns a “vco calibration busy flag” to GPO1. This output will be
high while the auto calibration is running.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Δ∑ Modulator Outputs (gpo_sel=10)
Setting register gpo_sel=10 (Reg1B<3:0> Table 37) assigns the three lsb’s of the delta sigma modulator output to
GPO<3:1> , where GPO1 is the lsb. This feature allows the possibility of using the HMC701LP6CE as a general
purpose digital delta sigma modulator for many possible applications.
External VCO
The HMC701LP6CE is targeted for ultra low phase noise applications with an external VCO. The synthesizer has
been designed to work with VCOs that can be tuned nominally over 0.5 to 4.5 Volts on the varactor tuning port with a
+5V charge pump supply voltage. Slightly wider ranges are possible with a +5.5V charge pump supply or with slightly
degraded performance. An external opamp active filter is required to support VCOs with tuning voltages above 5V.
External VCO with Active Inverting OpAmp Loop Filter
11
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 15
PLL - fractional-n synthesizer - SMT
An external opamp active filter is required to support external VCOs with tuning voltages above 5V. If an inverting
opamp is used with a positive slope VCO, phase_sel Reg05h <0> = 1 Table 16 must be set to invert the PFD phase
polarity and obtain correct closed loop operation.
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
PLL - fractional-n synthesizer - SMT
11
11 - 16
Figure 15. Conventional Synthesizer with VCO
Step Tuned VCO Support
In addition to conventional varactor tuned VCOs, the HMC701LP6CE also supports step tuned type VCOs, as shown
Figure 16. A step tuned VCO allows the user to center the VCO on the required output frequency while keeping the
varactor tuning voltage optimized near the mid-voltage tuning point of the synthesizer charge pump. This helps to keep
the tuning sensitivity more linear and reduces variations in kvco, which in turn minimizes variations in the closed loop
bandwidth of the locked oscillator. VCOs with up to 6-bits of discrete digital tuning, and up to 10-bits of total control
bits, are supported via a simple 3-wire VCO Serial Port.
If a step tuned VCO is used, the VCO switches are normally controlled automatically by the synthesizer using the auto
tune feature. The VCO switches may also be controlled directly from register bits Reg0B<4:0> of spivco_direct_data,
(Reg0Bh Table 22) via direct serial port access for testing or for other special purpose operation. Other control bits
specific to the VCO may be output from Reg0B<9:5>.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Figure 16. Step Tuned VCO
11
The HMC701LP6CE is capable of controlling external VCOs that support additional features on the VCO serial port
interface. Up to 10 data control bits may be written to an external VCO via Reg0Bh in Table 22. For example such
features as band selection or VCO power down may be supported in some VCOs.
Multiple VCO Control
Hittite step tuned VCOs are directly addressable (see Figure 31) and also supports the possibility of controlling
multiple HMC step tuned VCOs by sharing the VCO Serial Port lines as shown in Figure 17.
Figure 17. Multiple VCO Control
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
External VCO Control
11 - 17
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
VCO Tuning, Calibration & Temperature Correction
The HMC701LP6CE supports the use of an optional external step tuned VCO. A step tuned VCO allows the advantages
of low phase noise associated with a low kvco, a consistent loop voltage on the tuning varactor from part to part, and
lower charge pump voltages for a given range of VCO operation than would be possible with a conventional VCO with
only varactor tuning. This feature also helps to reduce synthesizer charge pump non-linearity by keeping the output
voltage of the charge pump as close as possible to the mid-rail condition.
Stepped Resonator VCO Calibration & Auto Tuning
PLL - fractional-n synthesizer - SMT
11
11 - 18
In order to use a step tuned VCO in a closed loop, the VCO must be calibrated such that the synthesizer knows which
switch position on the VCO is optimum for the desired output frequency. The HMC701LP6CE supports the automatic
calibration of the step tuned VCO. The calibration fixes the VCO tuning voltage at the optimum mid-point of the charge
pump output, then measures the free running VCO frequency on each switch setting and selects the setting which
results in the free running output frequency that is closest to the desired phase locked frequency. This procedure
results in a phase locked oscillator that locks over a very narrow voltage range on the varactor.
The calibration can be run automatically every time that a change of frequency is desired. This ensures optimum
selection of resonator settings vs. time and temperature. The accuracy desired in the calibration affects the amount
of time required to calibrate the VCO. The calibration routine searches for the best step setting that locks the VCO at
the current programmed frequency, while at a varactor voltage that is closest to mid-rail.
If it is desirable to switch frequencies very quickly it is possible to eliminate the calibration time by calibrating the VCO
in advance and storing the calibration information in the host. It will then be necessary for the host to run a routine that
interrogates the VCO over the desired range of operation and records the optimum resonator switch settings for the
desired frequency range. The calibration is then only run once on power up, and the settings stored in the host. The
host must then program the switch settings directly when changing frequencies.
Frequency programming of the synthesizer by the host, including switch selection, can be done in the background,
while the VCO is locked to the current frequency. The synthesizer normally writes the frequency control information
to the VCO, via the VCO Serial Port, upon receipt of a command that changes the PLL frequency, hence eliminating
calibration delay from the locking time.
A large change of frequency may require Main Serial Port writes to:
1. The dsm_seed register (Reg 11h Table 28),
2. VCO switch register spivco_direct_data (Reg0Bh Table 22),
3. Integer register dsm_intg (Reg0Fh Table 26) and
4. The fractional register dsm_frac (Reg10h Table 27).
This last register triggers the frequency change in fractional mode.
Smaller steps in frequency may require fewer register writes. Hence a maximum of 4 Main Serial Port transfers to the
synthesizer could be required to change frequencies. If the start phase of the fractional modulator is not of concern,
then it is not necessary to write the dsm_seed register. Similarly if the frequency step is small and the integer or the
vco switch settings do not change, then these registers may also be left constant. In all cases, in fractional mode, it is
necessary to write to the fractional register for frequency changes.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Frequency Change & VCO AutoCal
The HMC701LP6CE will update the active registers described above only when a frequency change is requested.
a. When in fractional mode (dsm_integer-mode Reg12h<3>=0) frequency change happens when the fractional
register is written (Reg10h Table 27). Integer register may be written first and is buffered until the frac register
is written.
b. When in Integer mode (dsm_integer-mode Reg12h<3>=1) frequency change happens when the integer
register is written (Reg0Fh Table 26). Frac register is not used.
c. If dsm_autoseed is enabled (Reg12h(7)=1), a frequency change updates the seed value of the fractional
modulator digital phase accumulator (DPA) with the value from the seed register Reg11h Table 28.
e. If a step tuned VCO is used and Auto tuning is disabled (Reg 0Ah(1)=1), then the frequency change will also
initiate the VCO Serial Port transfer to the VCO. The VCO will update its registers with the value from spivco_
direct_data (Reg0Bh Table 22) on the last clock tick of the VSCK (see VCO Serial Port WRITE Operation).
Buffering of the integer frequency value, seed value and vco tuning value allows the synthesizer and VCO to hold the
current frequency while new values are written. The synthesizer prescaler will only change when a valid frequency
change is written. If a step tuned VCO is used, and autotune is disabled, the VCO will be updated after the end of the
VCO Serial Port write cycle, about 16 clock cycles after the frequency change command.
Step Tuned VCO AutoCal on Frequency Change
Setting vcot_auto_start (Reg0Ah<0> Table 21) will cause the switched resonator VCO calibration to start automatically
whenever a frequency change is requested.
Step Tuned VCO Manual Calibration
Setting vcot_man_start (Reg0Ah<1>=1 Table 21) starts a switched resonator VCO calibration cycle for the current
programmed frequency. dsm_auto_start (Reg0Ah<0>=0) must be cleared. The value of the current VCO switch
setting determined by the calibration cycle is readable in the spivco_direct_data (Reg0Bh Table 22) register.
Step Tuned VCO Calibration Time & Accuracy
If a switched resonator VCO, is used, it may be calibrated by searching for the nearest resonator switch position that
yields the closest free running VCO frequency to the programmed frequency of the synthesizer. The measurement is
done with the VCO open loop and the varactor tuning port forced to VPPCP/2.
The VCO frequency is divided by 32 and counted for Tmmt. Tmmt is equal to 2vcot_ncyc_rdiv periods of the reference
crystal times vcot_xrefdiv_sel Reg0A<11:10> Table 21. The frequency result is the value in the vco counter, VCTR, as
shown in Figure 18. Currently only vcot_xrefdiv_sel = 1 is supported.
The nominal VCO frequency measured, fvcom, is given by
(EQ 1)
Where the worst case measurement error, ferro, is:
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
d. If a step tuned VCO is used and Auto tuning is enabled (Reg 0Ah(1)=1), then the frequency change will also
initiate the VCO autotuning calibration. Serial Port transfer to the VCO will happen automatically at the end of
the autotuning procedure. The VCO will update its registers on the last clock tick of the VSCK (see VCO Serial
Port WRITE Operation).
11 - 19
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
(EQ 2)
PLL - fractional-n synthesizer - SMT
11
11 - 20
Figure 18. VCO Calibration
The period of a single VCO calibration measurement, Tmmt, is given by:
(EQ 3)
Where
ncyc
vcot
= vcot_ncyc_rdiv Reg0A<5:2> Table 21
= Ref tune clock division ratio, vcot_xrediv_sel Reg0Ah<11:10>, Table 21
Note: Only vcot = 0 is supported currently
A 5-bit switched resonator VCO, for example, nominally requires 5 measurements for calibration, worst case 6, hence
total calibration time, worst case, is given by:
(EQ 4)
Normally we wish the absolute value of ferro to be less than one half of the VCO switched resonator step size specified
for the switched resonator VCO.
VCO Auto Tuning Example
Suppose our target frequency is to operate at 2.3 GHz with a nominal 1.5V on the charge pump. Our example crystal
is 50 MHz and vcot_xrefdiv_sel divider is 1, hence the auto calibration clock = 50 MHz. Note, when using autocal, the
maximum input crystal cannot exceed 60 MHz.
We must decide how long, and how accurate we need to make the tuning. Suppose the switched resonator lsb steps
are 6.5 MHz nominal, 6 MHz worst case.
A reasonable calibration target would be to set the calibration frequency error to one half the VCO lsb steps, i.e. ferro
<= 3 MHz. With some reasonable margin, lets target 2 MHz ferro worst case. Using (EQ 1) we see that the minimum
calibration measurement time for a single measurement must be
(EQ 5)
Hence we must choose ncyc such that Tmmt >Tmmtmin
Solving for (EQ 3)
(EQ 6)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
We arrive at a value of 10 for ncyc, and hence a single measurement period is Tmmt = 20.48 usec, the worst case
frequency error of the measurement is ±1.56 MHz and the total time to run the full calibration for a 5 bit switched VCO
is six measurements worst case, hence Tcal = 6 Tmmt = 122.9 usec, plus time for six VCO serial port transfers and state
machine housekeeping, typically about 90*R/fxtal, about 1.8 usec more.
Example Calibration Procedure with an Example External VCO
Using the above example calculation for calibration time and accuracy, the procedure to run the calibration is as
follows using an example VCO at 2.3 GHz:
The example VCO must first be set up to operate in the desired band, with, in this example, a 50 MHz crystal and a
50 MHz PFD frequency.
Then set up the auto calibration features as follows:
e. Set the auto calibration time by setting vcot_ncyc_rdiv = 1010 (Reg0Ah<5:2> Table 21)
f. Enable the auto calibration feature by setting vcot_auto_start (Reg0Ah<0> Table 21)
Then program the fractional frequency to start the calibration and change frequencies.
g. Set the fractional register to zero in this example, frac = 000000h (Reg10h Table 27)
The last step of programming the frequency register initiates the calibration which will run in about 124 usec, as per
our calculation. The state machine will write the autotune result into Reg20h Table 42. The synthesizer will then be
tuned to the commanded output frequency with the optimized switch setting on the VCO. The normal locking time will
apply after the calibration is run.
The optimum tuning setting for this frequency may be read by the host from read only register vcot_caps Reg20h<7:0>
(Table 42) and stored for later use for faster tuning to this frequency.
Manual VCO Control for Fast Frequency Changes
If the auto calibration reading is run first for a given frequency and the calibration settings are read and stored for later
use in the host, then a frequency change can be run without re-running the autocal routine.
Assume that the VCO band and reference are all programmed correctly in advance. Further that we disable the auto
calibration feature by clearing vcot_auto_start (Reg0Ah<0> Table 21).
Then a frequency change is executed as follows:
a. Write the calibration switch setting for the desired frequency to spivco_direct_data (Reg0Bh Table 22).
(VCO specific)
b. If necessary set the integer frequency register dsm_intg (Reg0Fh Table 26)
c. Write the fractional register to trigger the frequency change frac (Reg10h Table 27)
d. The synthesizer then automatically updates the fractional divider and initiates the VCO Serial Port transfer
for the new frequency
Calibration Polarity, Tune Word Inversion & Active Opamp Loop Filters
vcot_invert_outdata (Reg0Ah<6> Table 21) inverts the VCO tuning cap polarity. The polarity must be set to match the
VCO polarity in question or the autotune search algorithm will not work. This bit is normally set if an active loop filter
is used with an inverting opamp with a positive tuning slope VCO
11
PLL - fractional-n synthesizer - SMT
a. Setup the VCO register as required by the VCO (Reg0Bh Table 22)
b. Input a reference signal at 50 MHz
c. Set the Ref divider to divide by 1 , rfp_div_ratio = 00 0000 0000 0001, (Reg03h<13:0> Table 14)
d. Set the integer division, intg = 46d = 002Eh (Reg0Fh Table 26)
vcot_swap_outdata (Reg0Ah<7> Table 21) swaps the cap data left to right. This makes it easy to match the VCO in
use. Binary weighted caps are expected.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 21
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Temperature Sensor
The HMC701LP6CE features a built in temperature sensor which may be used as a general purpose temperature
sensor.
The temperature sensor is enabled via tsens_spi_enable (Reg1Eh=1 Table 40) and when enabled draws 2 mA.
The temperature sensor features a built in 3-bit quantizer that allows the temperature to be read in register tsens_
temperature (Reg21h Table 43). The temperature sensor data converter is not clocked. Updates to the temperature
sensor register are made by strobbing register tsens_spi_strobe (Reg00h<3> Table 11). The 3-bit quantizer operates
over a -40°C to +100°C range as follows:
TEMPERATURE SENSOR QUANTIZER OUTPUT
Tn = floor {(Temperature +40) / 17.5 where Tn is the decimal value of register tsens_temperature}
PLL - fractional-n synthesizer - SMT
11
11 - 22
(EQ 7)
7
6
5
4
3
2
1
0
-40
-20
0
20
40
60
TEMPERATURE (°C)
80
100
Figure 19. Typical Temperature Sensor Quantizer output
Temperature sensor slope is 17.5 mV/lsb. Absolute tolerances on the temperature sensor thresholds may vary by up
to ±10°C worst case.
Nominal temperature is given by:
(EQ 8)
Charge Pump & Phase Frequency Detector (PFD)
The Phase Frequency Detector or PFD has two inputs, one from the reference path divider and one from the VCO path
divider. The PFD compares the phase of the VCO path signal with that of the reference path signal and controls the
charge pump output current as a linear function of the phase difference between the two signals. The output current
varies linearly over a full ±2π radians input phase difference.
PFD Functions
phase_sel (Reg05h<0> Table 16) inverts the phase detector, polarity for use with an inverting opamp or negative
slope VCO.
upout_en in Reg05h<1> Table 16 allows masking of the PFD up output, which effectively prevents
the charge pump from pumping up.
dnout_en in Reg05h<2> Table 16 allows masking of the PFD down output, which effectively prevents
the charge pump from pumping down.
Charge Pump Tri-State
De-asserting both upout_en and dnout_en effectively tri-states the charge pump while leaving all other functions
operating internally.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
PFD Jitter & Lock Detect Background
In normal phase locked operation the divided VCO signal arrives at the phase detector in phase with the divided
crystal signal, known as the reference signal. Despite the fact that the device is in lock, the phase of the VCO signal
and the reference signal vary in time due to the phase noise of the crystal and VCO oscillators, the loop bandwidth
used and the presence of fractional modulation or not. The total integrated noise on the VCO path normally dominates
the variations in the two arrival times at the phase detector if fractional modulation is turned off.
If we wish to detect if the VCO is in lock or not we need to distinguish between normal phase jitter when in lock and
phase jitter when not in lock.
First, we need to understand what is the jitter of the synthesizer, measured at the phase detector in integer or fractional
modes.
Figure 20. Synthesizer Phase Noise & Jitter
With this simplification the single sideband integrated VCO phase noise, Ф2 , in rads2 at the phase detector is given
by
(EQ 9)
where
Ф2 SSB(ƒ0) is the single sideband phase noise in rads2/Hz inside the loop bandwidth, B is the 3 dB corner frequency of
the closed loop PLL and N is the division ratio of the prescaler
The rms phase jitter of the VCO in rads, Ф , results from the power sum of the two sidebands:
2
Ф = √ 2Ф SSB
(EQ 10)
Since the simple integral of (EQ 9) is just a product of constants, we can easily do the integral in the log domain.
For example if the VCO phase noise inside the loop is -100 dBc/Hz at 10 kHz offset and the loop bandwidth is
100 kHz, and the division ratio N=100, then the integrated single sideband phase noise at the phase detector in dB is
given by Ф2dB = 10log (Ф2(ƒ0)Bπ ⁄ N2) = -100 + 50 + 5 - 40 = -85 dBrads, or equivalently Ф = 10 -82/20 = 56 urads rms or
3.2 milli-degrees rms.
While the phase noise reduces by a factor of 20logN after division to the reference, the jitter is a constant.
11
PLL - fractional-n synthesizer - SMT
The standard deviation of the arrival time of the VCO signal, or the jitter, in integer mode may be estimated with a
simple approximation if we assume that the locked VCO has a constant phase noise, Ф2 (ƒ0), at offsets less than
the loop 3 dB bandwidth and a 20 dB per decade roll off at greater offsets. The simple locked VCO phase noise
approximation is shown on the left of Figure 20.
The rms jitter from the phase noise is then given by Tjnp = Tref Ф / 2π
In this example if the reference was 50 MHz, Tref = 20 nsec, and hence Tjpn = 178 femto-sec.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 23
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
A normal 3 sigma peak-to-peak variation in the arrival time therefore would be
±3 √ 2Tjpn = 0.756 ps
If the synthesizer was in fractional mode, the fractional modulation of the VCO divider will dominate the jitter. The exact
standard deviation of the divided VCO signal will vary based upon the modulator chosen, however a typical modulator
will vary by about ±3 VCO periods, ±4 VCO periods, worst case.
If, for example, a nominal VCO at 5 GHz is divided by 100 to equal the reference at 50 MHz, then the worst case
division ratios will vary by 100±4. Hence the peak variation in the arrival times caused by Δ∑ modulation of the
fractional synthesizer at the reference will be
(EQ 11)
PLL - fractional-n synthesizer - SMT
11
11 - 24
In this example, TjΔ∑pk = ±200 ps(104-96)/2 = ±800 psec. If we note that the distribution of the delta sigma modulation
is approximately gaussian, we could approximate TjΔ∑pk as a 3 sigma jitter, and hence we could estimate the rms jitter
of the Δ∑ modulator as about 1/3 of TjΔ∑pk or about 266 psec in this example.
Hence the total rms jitter Tj, expected from the delta sigma modulation plus the phase noise of the VCO would be given
by the rms sum , where
(EQ 12)
In this example the jitter contribution of the phase noise calculated previously would add only 0.764psec more jitter at
the reference, hence we see that the jitter at the phase detector is dominated by the fractional modulation.
Bottom line, we have to expect about ±0.8 nsec of normal variation in the phase detector arrival times when in
fractional mode. In addition, lower VCO frequencies with high reference frequencies will have much larger variations.,
for example, a 1 GHz VCO operating at near the minimum nominal divider ratio of 36, would, according to (EQ 11),
exhibit about ±4 nsec of peak variation at the phase detector, under normal operation. The lock detect circuit must not
confuse this modulation as being out of lock.
PFD Lock Detect
lkd_en (Reg01h<11> Table 12) enables the lock detect functions of the HMC701LP6CE.
The Lock Detect circuit in the HMC701LP6CE places a one shot window around the reference. The one shot window
may be generated by either an analog one shot circuit or a digital one shot based upon an internal ring oscillator timer.
Clearing lkd_ringosc_mono_select (Reg1Ah<14> Table 36) will result in a nominal ±10nsec ‘analog’ window of fixed
length, as shown in Figure 21. Setting lkd_ringosc_mono_select will result in a variable length ’digital’ widow. The
digital one shot window is controlled by lkd_ringosc_cfg (Reg1Ah<16:15>). The resulting lock detect window period is
then generated by the number of ring oscillator periods defined in lkd_monost_duration Reg1Ah<18:17> (Table 36).
The lock detect ring oscillator may be observed on the GPO2 port by setting ringosc_testmode (Reg1Ah<19> Table
36) and configuring the gpo_sel<3:0> = 0111 in (Reg1Bh Table 37). Lock detect does not function when this test mode
is enabled.
lkd_wincnt_max (Reg1Ah<9:0> Table 36) defines the number of consecutive counts of the VCO that must land inside
the lock detect window to declare lock. If for example we set lkd_wincnt_max = 1000 , then the VCO arrival would
have to occur inside the selected lock widow 1000 times in a row to be declared locked. When locked the Lock Detect
flag ro_lock_detect (Reg1Fh<0> Table 41) will be set. A single occurrence outside of the window will result in clearing
the Lock Detect flag, ro_lock_detect.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
The Lock Detect flag ro_lock_detect (Reg1Fh<0> Table 41) is a read only register, readable from the serial port. The
Lock Detect flag is also output to the LD_SDO pin according to lkd_to_sdo_always (Reg1Ah<13>) and lkd_to_sdo_
automux_en (Reg1Ah<12>), both in Table 36. Setting lkd_to_sdo_always will always display the Lock Detect flag
on LD_DSO. Clearing lkd_to_sdo_always and setting lkd_to_sdo_automux_en will display the Lock Detect flag on
LD_SDO except when a serial port read is requested, in which case the pin reverts temporarily to the Serial Data Out
pin, and returns to the lock detect function after the read is completed.
Figure 21. Normal Lock Detect Window
Lock Detect with Phase Offset
When operating in fractional mode the linearity of the charge pump and phase detector are more critical than in
integer mode. The phase detector linearity is worse when operated with zero phase offset. Hence in fractional mode
it is necessary to offset the phase of the reference and the VCO at the phase detector. In such a case, for example
with an offset delay, as shown in Figure 22, the mean phase of the VCO will always occur after the reference. The
lock detect circuit window can be made more selective with a fixed offset delay by setting win_asym_enable and
win_asym_up_select (Reg1Ah<11> Table 36). Similarly the offset can be in advance of the reference by clearing
win_asym_up_select while leaving win_asym_enable Reg1Ah<10> set both in Table 36.
Figure 22. Delayed Lock Detect Window
Cycle Slip Prevention (CSP)
When changing frequencies the VCO is not yet locked to the reference and the phase difference at the PFD varies
rapidly over a range much greater than ±2π radians. Since the gain of the PFD varies linearly with phase up to ±2π,
the gain of conventional PFDs will cycle from high gain, when the phase difference approaches a multiple of 2π, to
low gain, when the phase difference is slightly larger than a multiple of 0 radians. This phenomena is known as cycle
slipping. Cycle slipping causes the pull-in rate during the locking phase to vary cyclically as shown in the red curve in
Figure 23. Cycle slipping increases the time to lock to a value far greater than that predicted by normal small signal
Laplace analysis.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
11
11 - 25
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
The HMC701LP6CE PFD features Cycle Slip Prevention (CSP), an ability to virtually eliminate cycle slipping during
acquisition. When enabled, the CSP feature essentially holds the PFD gain at maximum until such time as the
frequency difference is near zero. CSP allows significantly faster lock times as shown in Figure 23. The use of the
CSP feature is enabled with pfds_rstb (Reg01<15> Table 12). The CSP feature may be optimized for a given set
of PLL dynamics by adjusting the PFD sensitivity to cycle slipping. This is achieved by adjusting pfds_sat_deltaN
(Reg1C<3:0> Table 38).
PLL - fractional-n synthesizer - SMT
11
11 - 26
Figure 23. Cycle Slip Prevention (CSP)
Charge Pump Gain
A simplified diagram of the charge pump is shown in Figure 24. Charge pump up and down gains are set by cp_
UPcurrent_sel and cp_DNcurrent_sel respectively (Reg07 Table 18). Normally the registers are set to the same
value. Each of the UP and DN charge pumps consist of 5-bit charge pumps with lsb of 125 µA. The current gain of the
pump, in Amps/radian, is equal to the gain setting of this register divided by 2π.
For example if both cp_UPcurrent_sel and cp_DNcurrent_sel are set to ’01000’ the output current of each pump will
be 1mA and the gain Kp = 1mA/2π radians, or 159 uA/rad.
Charge Pump Gain Trim
In most applications Gain Trim is not used. However it is available for special applications.
Each of the UP and DN pumps may be trimmed separately to more precise values to improve current source matching
of the UP and DN values, or to allow finer control of pump gain.
The pump trim controls are 3-bits, binary weighted for UP and DN, in cp_UPtrim_sel and cp_DNtrim_sel respectively
(Reg 08h Table 19). LSB weight is 14.7 uA, x000 = 0 trim, x001 = 14.7 ua added trim, x111 = 100uA.
Charge Pump Phase Offset
Either of the UP or DN charge pumps may have a DC leakage or “offset” added. The leakage forces the phase detector
to operate with a phase offset between the reference and the divided VCO inputs. It is recommended to operate with
a phase offset when using fractional mode to reduce non-linear effects from the UP and DN pump mismatch. Phase
noise in fractional mode is strongly affected by charge pump offset.
DC leakage or “offset” may be added to the UP or DN pumps using cp_UPoffset_sel and cp_DNoffset_sel (Reg08
Table 19). These are 4 bit registers with 28.7uA LSB. Maximum offset is 430uA.
As an example, if the main pump gain was set at 1mA, an offset of 373uA would represent a phase offset of about
(392/1000)*360 = 133degrees.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Figure 24. Charge Pump Gain, Trim and Phase Offset Control
Frequency Programming
The HMC701LP6CE can operate in either fractional mode or integer mode. In integer mode of operation the delta
sigma modulator is disabled. Frequency programming and mode control is described below.
Fractional Frequency
The fractional frequency synthesizer, when operating in fractional mode, can lock to frequencies which are fractional
multiples of the reference frequency.
Fractional mode is the default mode. To run in fractional mode ensure that dsm_integer_mode Reg12h<5> Table 29
is clear and dsm_rstb Reg01<13> Table 12). Then program the frequency as explained below:
The output frequency of the synthesizer is given by, fvco, where
Fractional Frequency
of VCO
(EQ 13)
where
Nint
is the integer division ratio, an integer number between 36 and 65,533
(dsm_intg (Reg0Fh Table 26))
Nfrac
is the fractional part, a number from 1 to 224 (dsm_frac Reg10h Table 27)
R
is the reference path division ratio, (rfp_div_ratio Reg03h<13:0> Table 14)
fxtal
is the frequency of the crystal oscillator input (XSIN or XREF Figure 10)
fxtal
R
fref
Nint
Nfrac
= 50 MHz
=1
= 50 MHz
= 46
=1
As an Example:
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
11
11 - 27
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
(EQ 14)
In this example the output frequency of 2,300,000,002.98 Hz is achieved by programming the 16-bit binary value of
46d = 2Eh = 0000 0000 0010 1110 into dsm_intg.
Similarly the 24-bit binary value of the fractional word is written into dsm_frac,
1d = 000 001h = 0000 0000 0000 0000 0000 0001
Example 2: Set the output to 4.600 025 GHz using a 100 MHz reference, R=2.
Find the nearest integer value, Nint, Nint = 92, fint = 4.600 000 GHz
PLL - fractional-n synthesizer - SMT
11
11 - 28
This leaves the fractional part to be ffrac =25 kHz
(EQ 15)
Since Nfrac must be an integer number, the actual fractional frequency will be 25,001.17 Hz, an error of 1.17 Hz.
Here we program the 16-bit Nint = 92d = 5Ch = 0000 0000 0101 1100 and
the 24-bit Nfrac = 8389d = 20C5h = 0000 0010 0000 1100 0101
In addition to the above frequency programming words, the fractional mode must be enabled using the frac register.
Other DSM configuration registers should be set to the recommended values. Register setup files are available on
request.
Integer Frequency
The synthesizer is capable of operating in integer mode. In integer mode the digital Δ∑ modulator is normally shut
off and the division ratio of the VCO divider is set at a fixed value. To run in integer mode set dsm_integer_mode
(Reg12h<3> Table 29) and clear dsm_rstb (Reg01h<13> Table 12). Then program the integer portion of the frequency,
NINT, as explained by (EQ 13), ignoring the fractional part.
Frequency Hopping Trigger
If the synthesizer is in fractional mode, a write to the fractional frequency register, Reg10h Table 27, will initiate the
frequency hop on the falling edge of the 31st clock edge of the serial port write (see Figure 29).
If the integer frequency register, Reg0Fh Table 26, is written when in fractional mode the information will be buffered
and only executed when the fractional frequency register is written.
If the synthesizer is in integer mode, a write to the integer frequency register, Reg0Fh Table 26, will initiate the
frequency hop on the falling edge of the 31st clock edge of the serial port write (see Figure 29).
Power On Reset (POR)
Normally all logic cells in the HMC701LP6CE are reset when the device digital power supply, DVDD, is applied. This
is referred to as Power On Reset, or just POR. POR normally takes about 500us after the DVDD supply exceeds 1.5V,
guaranteed to be reset in 1msec. Once the DVDD supply exceeds 1.5V, the POR will not reset the digital again unless
the supply drops below 100mV.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Soft Reset
The SPI registers may also be soft reset by an SPI write to strobe global_swrst_regs (Reg00h<0> Table 11).
All other digital, including the fractional modulator, may be reset with an SPI write to strobe global_swrst_dig
(Reg00h<1> Table 11).
Hardware Reset
The SPI registers may also be hardware reset by holding RSTB, pin 19, low.
Power Down
CW Sweeper Mode
The HMC701LP6CE features a built in frequency sweeper function. This function supports external or automatic
triggered sweeps. The maximum sweep range is limited to 255 x Fxtal/R. For example, with a 25 MHz comparison
frequency, the maximum sweep range is 6375 MHz. The start and end frequency points must be within 6375 MHz of
one another.
Sweeper Modes include:
a. 2-Way Sweep Mode: alternating positive and negative frequency ramps.
b. 1-Way Sweep Mode
c. Single Step Ramp Mode
Applications include test instrumentation, FMCW sensors, automotive radars and others. The parameters of the
sweep function are illustrated in Figure 26.
The sweep generator is enabled with ramp_enable in (Reg14h<1> Table 30). The sweep function cycles through a
series of discrete frequency values, which may be
a. Stepped by an automatic sequencer, or
b. Single stepped by individual triggers in Single Step Mode.
Triggering of each sweep, or step, may be configured to operate:
a. Via a serial port write to Reg14h<2> ramp_trigg (if Reg 14h<2> = 0 )
b. Automatically generated internally,
c. Triggered via TTL input on GPO3 Reg14h<5> = 1.
Sweep parameters are set as follows:
Initial Frequency, fo = Current frequency value of the synthesizer, (EQ 15)
Final Frequency, ff = Frequency of the synthesizer at the end of the ramp
The frequency step size while ramping is controlled by rampstep, (Reg15h Table 31).
Frequency Step Size ∆ƒstep = rampstep • fxtal / 224 • R
11
PLL - fractional-n synthesizer - SMT
The HMC701LP6CE may be powered down by writing a zero to Reg01h Table 12. In power down state the
HMC701LP6CE should draw less than 10uA. It should be noted that Reg01h is the Enable and Reset Register which
controls 16 separate functions in the chip. Depending upon the desired mode of operation of the chip, not all of the
functions may be enabled when in operation. Hence power up of the chip requires a selective write to Reg01 bits.
An easy way to return the chip to its prior state after a power down is to first read Reg01h and save the state, then
write a zero to Reg01h for reset and then simply rewrite the previous value to restore the chip to the desired operating
mode.
where R is the value of the reference divider (rfp_div_ratio in Table 14)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 29
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
CW Sweeper Mode (Continued)
Clearing or setting ramp_startdir_dn, (Reg14h<4> Table 30), sets the initial ramp direction to be increasing or
decreasing in frequency respectively. Setting ramp_singledir (Reg14h<7> Table 30), restricts the direction of the
sweep to the initial sweep direction only.
The sweeper timebase Tref is the period of the divided reference, fPFD, at the phase detector Tref
The total number of ramp steps taken in a single sweep is given by ramp_steps_number in Reg16h Table 32.
The total time to ramp from fo to ff is given by Tramp = Tref
•
The final ramp frequency, ff, is given by ƒƒ = ƒi + ∆ƒstep
ramp_steps_number
•
ramp_steps_number
Sweeper action at the end of sweep depends upon the mode of the sweep:
PLL - fractional-n synthesizer - SMT
11
11 - 30
a. With both ramp_singledir and ramp_repeat_en disabled, at the end of the ramp time, Tramp,
the sweeper will dwell at the final frequency ff, until a new trigger is received. The next trigger will
reverse the current sequence, starting from ff, and stepping back to fo. Odd triggers will ramp in the
same direction as the initial ramp, even triggers will ramp in the opposite direction.
b. with ramp_singledir enabled and ramp_repeat_en disabled, at the end of the ramp time, Tramp,
the sweeper will dwell at the final frequency ff, until a new trigger is received. The second trigger
will hop the synthesizer back to the initial frequency, fo. The third trigger will restart the sweep from
fo. Hence all odd numbered triggers will start a new ramp in the same direction as the initial ramp,
even numbered triggers will hop the synthesizer from the current frequency to fo , where it will wait
for a trigger to start a sweep.
Ramp Busy
In all types of sweeps ramp_busy will indicate an active sweep and will stay high between the 1st and nth ramp step.
ramp_busy may be monitored one of two ways. ramp_busy is readable via read only register Reg1Fh<5> Table 41.
ramp_busy may also be monitored on GPO2, hardware pin 24, by setting Reg1Bh<3:0> =8h Table 37.
Autosweep Mode
The Autosweep mode is similar to Figure 26 except that once started, triggers are not required. Once enabled, (ramp_
repeat_en=1 Reg14h<3> Table 30) the Autosweep mode initiates the first trigger, steps n times, one step per ref clock
cycle, and then waits for the programmed dwell period and automatically triggers the ramp in the opposite direction.
The sweep process continues alternating sweep directions until disabled. dwell_time (Reg17h Table 33) controls the
number of Tref periods to wait at the end of the ramp before automatically retriggering a new sweep.
2-Way Sweeps
If ramp_repeat_en (Reg14h<3> Table 30) is cleared, then the ramps are triggered by
a. Writing to ramp_trigg (Reg14h<2> Table 30), if bit <2> = 0, or
b. by rising edge TTL signal input on GPO3, if ramp_trig_ext_en is set, and GPO3 is enabled.
All functions are the same in Figure 26 for Autosweep or 2-Way Triggered sweeps, the only difference is the trigger
source is generated internally for autosweep, and is input via serial port or GPO3 for triggered sweeps. Sweep_busy
will go high at the start of every ramp and stay high until the nth step in the ramp.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Figure 26. 2-Way Sweep Control via Trigger
Triggered 1-Way Sweeps
1-Way sweeps are shown in Figure 27.
Unlike 2-Way sweeps, 1-Way sweeps require that the VCO hop back to the start frequency after the dwell period.
Triggered 1-Way sweeps also require a 3rd trigger to start the new sweep. The 3 rd trigger must be timed appropriately
to allow the VCO to settle after the large frequency hop back to the start frequency. Subsequent odd numbered
triggers will start the 1-Way sweep and repeat the process.
Figure 27. 1-Way Sweep Control
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
11
11 - 31
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Single Step Ramp Mode
A Single Step 1-Way Ramp is shown in Figure 28. In this mode, a trigger is required for each step of the ramp. Single
step will function in either 1-Way or 2-Way ramps. Similar to autosweep, the ramp_busy flag will go high on the first
trigger, and will stay high until the nth trigger. The n+1 trigger will cause the ramp to jump to the start frequency in
1-way ramp mode. The n+2 trigger will restart the 1-way ramp.
PLL - fractional-n synthesizer - SMT
11
Figure 28. Single Step Ramp Mode
The user should be aware that the synthesized ramp is subject to normal phase locked loop dynamics. If the loop
bandwidth in use is much wider than the rate of the steps then the locking will be very fast and the ramp will have a
staircase shape. If the update rate is higher than the loop bandwidth, as is normally the case, then the loop will not
fully settle before a new frequency step is received. Hence the swept output will have a small lag and will sweep in a
near continuous fashion.
MAIN SERIAL PORT
The HMC701LP6CE features a four wire serial port for simple communication with the host controller. Register types
may be Read Only, Write Only, Read/Write or Strobe, as described in the registers descriptions. The synthesizer also
features an auxiliary 3-wire serial port, known as the VCO Serial Port. The VCO Serial Port is a write only interface
from the synthesizer to an optional switched resonator VCO that supports 3-wire serial port control.
Typical main serial port operation can be run with SCLK at speeds up to 50 MHz. Serial port registers are described
in the section REGISTER MAP.
[1] Phase-Error Measurement and Compensation in PLL Frequency Synthesizers for FMCW, Sensors—I: Context and Application, Pichler, Stelzer,
Member, IEEE, Seisenberger, and Vossiek, IEEE Transactions on Circuits and Systems—I, VOL. 54, No. 5, May 2007
11 - 32
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Serial Port WRITE Operation
AVDD = DVDD = 3V ±10%, AGND = DGND = 0V
Table 4. Timing Characteristics
Conditions
Min.
Typ.
Max
Units
t1
SEN to SCLK setup time
8
t2
SDI to SCLK setup time
10
nsec
nsec
t3
SDI to CLK hold time
10
nsec
t4
SCLK high duration
8
nsec
t5
SCLK low duration
8
nsec
t6
SEN High duration
640
nsec
t7
SEN low duration
20
nsec
A typical WRITE cycle is shown in Figure 29.
a. The Master (host) both asserts SEN (Serial Port Enable) and clears SDI to indicate a WRITE
cycle, followed by a rising edge of SCLK.
b. The slave (synthesizer) reads SDI on the 1st rising edge of SCLK after SEN. SDI low initiates
the WRITE cycle (/WR)
c. Host places the six address bits on the next six falling edges of SCLK, MSB first.
d. Slave registers the address bits in the next six rising edges of SCLK (2-7).
e. Host places the 24 data bits on the next 24 falling edges of SCK, MSB first .
f. Slave registers the data bits on the next 24 rising edges of SCK (8-31).
g. SEN is de-asserted on the 32nd falling edge of SCLK.
h. The 32nd rising edge of SCLK completes the cycle
Figure 29. Serial Port Timing Diagram - WRITE
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Parameter
11 - 33
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Main Serial Port READ Operation
The synthesizer uses the multi-purpose pin, LD_SDO, for both Lock Detect and Serial Data Out (SDO) functions. The
registers lkd_to_sdo_automux_en (Reg1A<12>) and lkd_to_sdo_always (Reg1A<13> Table 36) determine how the
Data Output pin is muxed with the Lock Detect function. If both of the registers are cleared, then the pin is exclusively
SDO. If automux is enabled, the pin switches to SDO when the RD function is sensed on the 1st rising edge of SCLK.
If lkd_to_sdo_always is set, then the pin LD_SDO is dedicated for Lock Detect only, and it is not possible to read from
the synthesizer.
A typical READ cycle is shown in Figure 30.
PLL - fractional-n synthesizer - SMT
11
11 - 34
a. The Master (host) asserts both SEN (Serial Port Enable) and SDI to indicate a READ
cycle, followed by a rising edge SCLK
b. The slave (synthesizer) reads SDI on the 1st rising edge of SCLK after SEN. SDI high initiates
the READ cycle (RD)
c. Host places the six address bits on the next six falling edges of SCLK, MSB first.
d. Slave registers the address bits on the next six rising edges of SCLK (2-7).
e. Slave places the 24 data bits on the next 24 rising edges of SCK (8-31), MSB first .
f. Host registers the data bits on the next 24 falling edges of SCK (8-31).
g. SEN is de-asserted on the 32nd falling edge of SCLK.
h. The 32nd falling edge of SCLK completes the cycle
Figure 30. Serial Port Timing Diagram - READ
VCO SERIAL PORT
The VCO Serial Port is a 3-wire serial port that may be used to control external step tuned VCOs that support serial
port control. Visit the Hittite website or contact Hittite Sales for a full list of compatible VCOs. The VCO Serial Port is
a 3-wire serial port that may be used to control external step tuned VCOs that support serial port control. The 3-wire
VCO serial port uses the following pins, as shown in Figure 31:
VSDO: VCO Serial Port Data Out
VSCK: VCO Serial Port Clock
VSLE: VCO Serial Port Latch Enable
The VCO Serial Port transfers the contents of the 16-bit register spivco_direct_data (Reg0Bh Table 22) to the VCO
upon receipt of a frequency change command. The lsbs of spivco_direct_data are the switch settings for the VCO and
may be set directly or by the autotune routine described in the section Step Tuned VCO Support. Multiple VCO formats
are supported for autotuning. VCO tuning bits are configured with sar_bits_number (Reg0Dh<5:4> Table 24). Multiple
VCO SPI formats are also supported and are configured by spivco_mode (Reg0Dh<1:0> Table 24).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
The msbs of Reg0Bh, are VCO control bits and are also VCO specific. The VCO should be designed to only register
the data upon receipt of the latch signal, VSLE.
Multiple VCO control can be implemented by addressing the individual VCOs.
VCO Serial Port WRITE Operation
DVDD = 3V ±10%, DGND = 0V
Table 5. Timing Characteristics
Conditions
Min.
Typ.
Max
Units
t1
VSLE to VSDO setup time
8
nsec
t2
VSDO to VSCK setup time
10
nsec
t3
VSDO to VSCK hold time
10
nsec
t4
VSCK high duration
8
nsec
t5
VSCK low duration
8
nsec
t6
VSLE high duration
8
nsec
VCO Serial port status is flagged in Read Only register spi_vco_busy (Reg1Fh<4> Table 41).
Individual step tuned VCOs may have different capabilities, such as power down, or divide by two outputs, and may
also have different number of switches in the resonator. The HMC701LP6CE can adapt its control format and number
of tuning bits used in the autotuning routine as described in Reg0Dh Table 24.
16-Bit VCO Write Cycle
HMC VCOs that support the 16-bit write cycle described here are fully addressable via the VSPI control.
A typical 16-bit VCO WRITE cycle is shown in Figure 31.
a. The Synthesizer (Master) both clears VSLE (VCO Serial Port Latch) and places data bit d8 (msb) on VSDO.
b. the synthesizer places a rising edge on VSCK to shift d8 into the VCO
c. Synthesizer places the next eight data bits, d7:d0, on the next eight falling edges of VSCLK, LSB last.
d. The synthesizer clocks each data bit on the next eight rising edges of VSCLK .
e. Synthesizer places the next four VCO Register bits, r3:r0, on the next four falling edges of VSCLK, LSB last.
f. Synthesizer places the next three VCO address bits, a2:a0, on the next three falling edges of
VSCLK, LSB last.
g. The synthesizer asserts VSLE after the falling edge of the 16th VSCK, which latches the data into the VCO
h. the synthesizer clears VSLE to complete the cycle
11
PLL - fractional-n synthesizer - SMT
Parameter
Figure 31. VCO Serial Port Timing Diagram - WRITE ONLY
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 35
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Typical Step Tuned VCO Register Map
Step Tuned VCO Registers Example
Note: HMC step tuned VCOs come in different configurations. The following four registers give
examples of typical control registers in HMC step tuned VCOs. Consult the VCO data sheet to
confirm available VCO features.
Table 6. VSPI Format
Bit
Name
[2:0]
11
PLL - fractional-n synthesizer - SMT
Width
Default
3
n/a
Description
VCO Address, MSB First
[6:3]
VCO Register Address
4
n/a
VCO Register Address
[15:7]
VCO Data
9
n/a
VCO Data Bits
Table 7. VCO R00 (Switch Controller Register)
Bit
Name
[0]
11 - 36
VCO ID
Enable Calibration
Width
1
[6:1]
Tune control
6
[8:7]
Not Used
2
Default
Description
0
Reserved for Calibration mode, forces a locally
generated temperature compensated voltage on the VCO
tuning port
100000
b
6 bit tuning control
000000 minimum tuning capacitance
000001 next to minimum
...
111111 maximum tuning capacitance
Not Used
Table 8. VCO R01 (Enable Register)
Bit
Name
[3:0]
Reserved
Width
Default
4
x
Description
Reserved
[4]
PLL Buffer En
1
1
PLL Buffer Enable (Low power output to PLL)
[5]
Divider En
1
1
Divider Enable (if present)
[6]
Buffer En
1
1
Buffer Enable (High power RF output to application)
[7]
VCO En
1
1
VCO Enable
1
1
Global Enable
0: Forces all cells to power down state
1: Enables individual Cell state control via bits 4 thru 7.
Global En
[8]
Table 9. VCO R02 (Bias Control Register)
Bit
Name
Width
Default
Description
[1:0]
PLL Buffer Bias Bits
(MSB:LSB)
2
1
0: Min Bias
1: Next to min bias
2: Next to max bias
3: Max Bias
[3:2]
Divider or Doubler Bias Bits
(MSB:LSB), if present in VCO
2
00
0: Min Bias
1: Next to min bias
2: Next to max bias
3: Max Bias
[5:4]
Mixer Buffer Bias Bits
(MSB:LSB)
2
00
0: Min Bias
1: Next to min bias
2: Next to max bias
3: Max Bias
[8:6]
Reserved
3
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 10. VCO R03 (Temperature & Gain Control Register)
Name
Default
Reserved
5
[6:5]
Temp Compensation Offset Control
(MSB: LSB)
[8:7]
PLL Buffer Gain Control (MSB: LSB)
Description
x
Reserved
2
1
0: Reduce Tuning voltage 50mV
1: Use default Tuning voltage
2: Increase Tuning voltage 50mV
3: Increase Tuning voltage 100mV
2
1
0: Min Gain
1: Next to Min Gain
2: Next to Max Gain
3: Max Gain
REGISTER MAP
11
Reg 00h Chip ID (Read Only) Register
Bit
Type
[23:0]
Ro
Name
Chip ID
Width
Default
24
581502
Description
Chip ID
Table 11. Reg 00h Strobe (Write Only) Register
Bit
Type
0
STR
Name
global_swrst_regs
Width
Default
1
0
Description
Strobe to soft reset the SPI registers
1
STR
global_swrst_dig
1
0
Strobe to soft reset the rest of digital
2
STR
mcnt_resynch
1
0
Reserved
3
STR
tsens_spi_strobe
1
0
Strobe to clock the temp measurement on
demand
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
Bit
[4:0]
11 - 37
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 12. Reg 01h Enable & Reset Register
PLL - fractional-n synthesizer - SMT
11
11 - 38
Bit
Type
0
R/W
malg_vcobug_en
Name
1
Default
1
Description
1
R/W
mag_bias_en
1
1
Bias enable
VCO Buffer Enable
2
R/W
rfp_div_en
1
0
Enables / Holds refdiv in reset
Holding Ref divider in reset is equivalent to
bypassing the divider, see Figure 10
3
R/W
xrefmux_todig_en
1
1
Enables clock gate for xtal muxed (sq or sin)
reference to digital
4
R/W
rfp_div_todig_en
1
0
Enables divided reference clock to the digital
see Figure 10
5
R/W
rfp_sqr_todig_en
1
0
Enables square wave xtal clock to main digital
see Figure 10
6
R/W
rfp_sin_todig_en
1
0
Enables sine wave xtal clock to main digital
see Figure 10
7
R/W
rfp_bug_sq_en
1
1
Enables Square wave Ref Buffer, see Figure 10
8
R/W
rfp_bug_sin_en
1
0
Enables Sine wave Ref Buffer, see Figure 10
9
R/W
vcop_todig_en
1
0
1= divided VCO as digital, Δ∑ modulator clock
0= Divided Ref path as the
10
R/W
vcop_presc_en
1
1
Enables the prescaler bias
11
R/W
pfd_lkd_en
1
0
Enable / Resetb to digital lockdetect circuit and
PFD’s lockdetect output gates
12
R/W
cp_en
1
1
Charge Pump Enable, disable is tri-stated output
13
R/W
dsm_rstb
1
0
1 - Enables fractional modulator
see also dsm_integer_mode Reg12h<3>
14
R/W
lkd_rstb
1
0
1 - enables lock detect circuit
15
R/W
pfds_rstb
1
1
CSP PFD FF rstb
1 - Enables the Cycle Slip Prevention (CSP)
feature of the PFD
Table 13. Reg 02h Serial Data Out Force Register
Bit
Type
Name
Default
Description
0
R/W
malg_sdo_driver_force_val
1
Serial Data Out Force value
This value may be forced onto LD_SDO by
setting malg_sdo_driver_force_en
1
R/W
malg_sdo_driver_force_en
1
Serial Data Out EN Force enable
Places value from malg_sdo_driver_force_val on
SDO
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 14. Reg 03h Reference Path Register
Bit
Type
Name
Default
Description
13:0
R/W
rfp_div_ratio
also referred to as ‘R’
0
Divides the crystal input by this number ‘R’ if
rfp_div_en=1 and rfp_div_select = 1
rfp_div_ratio = 0 not allowed
2<=div_ratio<=2^14
see Figure 10
14
R/W
rfp_div_select
0
1 = reference divider enabled
0 = bypass ref divider
see Figure 10
15
R/W
rfp_auto_refdiv_sel_en
0
1 = auto ref divider enable or bypass is automatic
if rfp_div_ratio = 1, bypass divider
if rfp_div_bypass ~=1 use divider
see Figure 10
16
R/W
rfp_buf_sin_sel
0
Selects sine wave reference for normal operation
see Figure 10
11
Bit
0
Type
R/W
Name
vcop_dutycycmode
Default
0
Description
Extends the low time from 15 to 47 VCO cycles
for large divide ratios
Table 16. Reg 05h Phase Freq Detector Register (pfd)
Bit
Type
Name
Default
Description
0
R/W
pfd_phase_sel
0
Inverts PFD Polarity
0 = Passive Filter +ve slope VCO
1 = Passive Filter -ve slope VCO
1 = Active inverting filter, +ve slope VCO
0 = Active inverting filter, -ve slope VCO
1
R/W
pfd_upout_en
1
Allows masking of the up outputs between PFD
and CP
2
R/W
pfd_dnout_en
1
Allows masking of the dn outputs between PFD
and CP
Table 17. Reg 06h Phase Freq Detector Delay Register
Bit
Type
2:0
R/W
Name
pfd_del_sel
Default
2
Description
Delay line setpoint to PFD
Table 18. Reg 07h Charge Pump UP/DN Control Register
Bit
Type
Name
Default
Description
4:0
R/W
cp_UPcurrent_sel
16
Sets Charge-Pump Up gain, 125uA lsb, binary,
4mA max
9:5
R/W
cp_DNcurrent_sel
16
Sets Charge-Pump Dn gain, 125uA lsb, binary,
4mA max
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
PLL - fractional-n synthesizer - SMT
Table 15. Reg 04h Prescaler Duty Cycle Register
11 - 39
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 19. Reg 08h Charge Pump Trim & Offset Register
Bit
Type
3:0
R/W
cp_UPtrim_sel
Name
Default
0
Trim Up gain, 14.3uA lsb, binary, 100uA max
Description
7:4
R/W
cp_DNtrim_sel
0
Trim Dn gain, 14.3uA lsb, binary, 100uA max
11:8
R/W
cp_UPoffset_sel
4
Up Offset leakage current, 28.7uA lsb, binary,
430uA max
15:12
R/W
cp_DNoffset_sel
0
Dn Offset leakage current, 28.7uA , binary,
430uAmax
17:16
R/W
cp_amp_bias_sel
2
Charge Pump Dummy Branch Op amp bias
selection, 100uA
Table 20. Reg 09h Charge Pump EN Register
PLL - fractional-n synthesizer - SMT
11
11 - 40
Bit
Type
0
R/W
cp_pull_updn_en
Name
Default
0
Enables CP UP/Down Control Reg09 [1]
Description
1
R/W
cp_pull_dn_upb
0
0 - Forces Charge Pump Up when Reg09[0]=1
1 - Forces Charge Pump DN when Reg09[0]=1
Table 21. Reg 0Ah VCO Auto Tune & Control Register
Bit
Type
Name
Default
Description
0
R/W
vcot_auto_start
0
Enables Auto start of VCO cap tuning when frac
word is written to spi
1
R/W
vcot_man_start
0
Starts manual vco tuning when auto_start=0
(must be cleared to 0 before another tune)
5:2
R/W
vcot_ncyc_rdiv
2
Exponent selection for number of rdiv cycles to
wait during measurement (effects time to perform
the measurement and hence the accuracy)
6
R/W
vcot_invert_outdata
0
Inverts the vco tuning cap polarity
7
R/W
vcot_swap_outdata
0
Swaps the cap tuning data (left-to-right)
8
R/W
vcot_force_data_en
0
Force enable for the VCO tuning cap word Obsolete
9
R/W
vcot_force_dblbuff_mode
0
Enables double buffer for vco caps. Caps will go
to the vco when dsm_frac reg is written
0
xref divider generate vco tuning calibration
clock, and VCO Serial Port Clock VSCK from the
crystal input (see Figure 10) . This divider affects
calibration time and accuracy, currently only
divby1 is supported
00-->div by 1
01-->div by 2 not supported
10-->div by 4 not supported
11-->div by 8 not supported
11:10
R/W
vcot_xrefdiv_sel
Table 22. Reg 0Bh VCO Tuning & Control Register
Bit
Type
15:0
R/W
Name
spivco_direct_data
Default
0
Description
Used to set VCO control settings VCO Specific,
see VCO SERIAL PORT description
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 23. Reg 0Ch VCO Auto Tune Wait Register
Bit
Type
13:0
R/W
Name
Default
vcot_initial_wait
256
Description
Initial wait time (xtal cycles) after tri-stating
charge-pump to start VCO tuning
Table 24. Reg 0Dh VCO Control Register
Type
1:0
R/W
3:2
R/W
Name
Default
spivco_mode
f1_modesel
Description
0
Support for different VCO SPI formats
0: 16-bit VSPI
1: 10-bit VSPI with 5-bit SAR
2: 10-bit VSPI with 6-bit SAR
3: blank VCOSPI data
0
CSP Speedup Function Increases CSP current
when Lock Detect window exceeds threshold
0: disabled
1: 1nsec threshold
2: 3nsec threshold
3: 5nsec threshold
5:4
R/W
sar_bits_number
0
Autotune Successive Approximation Register
(SAR)
Autotune Algorithm supports VCOs with 5, 6, 7
or 8-bit step tuning
8-n = SAR bits
0: 8 bit SAR
1: 7 bit SAR
2: 6 bit SAR
3: 5 bit SAR
6
R/W
autocal_when_unlocked
0
0 : disabled
1: automatically runs the autotuning routine to
relock the VCO if loss of lock is detected
Table 25. Reg 0Eh Reserved
Bit
Type
23:0
R/W
Name
Default
Reserved
0
Description
Reserved
Table 26. Reg 0Fh Integer Division Register
Bit
Type
15:0
R/W
Name
dsm_intg
Default
200d
Description
unsigned integer portion of VCO divider value,
also known as NINT, see (EQ 12)
Table 27. Reg 10h Fractional Division Register
Bit
Type
23:0
R/W
Name
dsm_frac
Default
0
Description
unsigned fractional portion of VCO divider also
known as NFRAC, see (EQ 12)
Table 28. Reg 11h Seed Register
Bit
Type
23:0
R/W
Name
dsm_seed
Default
0
Description
unsigned seed value for Δ∑ modulator
sets the start phase of the modulator
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Bit
11 - 41
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 29. Reg 12h Delta Sigma Modulator Register
PLL - fractional-n synthesizer - SMT
11
11 - 42
Bit
Type
0
R/W
dsm_ref_clk_select
Name
Default
0
use reference instead of divider
Description
1
R/W
dsm_invert_clk_sd3
1
invert Δ∑ clk
2
R/W
dsm_invert_clk_rph
0
inverts the ref clock phase
1- enables Integer Mode, bypasses the Δ∑
modulator, leaves it running
see also dsm_rstb Reg01h<13> to disable the
modulator
3
R/W
dsm_integer_mode
0
4
R/W
Reserved
0
5
R/W
Reserved
0
6
R/W
dsm_xref_sin_select
0
when xref is selected specifies that the sine
source is used
7
R/W
dsm_autoseed
1
automatic seed load when changing the frac
part, uses value in seed
9:8
R/W
dsm_order
2
00-first order 01-second 10-third fb 11-third ff
13:10
R/W
dsm_quant_max
4’b0111
max value allowed out of Δ∑ modulator quantizer
limits are +7 to -8, typ ±3 or ±4
17:14
R/W
dsm_quant_min
4’b1000
min value allowed out of Δ∑ modulator quantizer
limits are +7 to -8, typ ±3 or ±4
Table 30. Reg 14h CW Sweep Control Register
The maximum sweep range is limited to 255 x Fxtal/R
Bit
Type
0
R/W
clear_ovf_undf
Name
Default
0
asynchronous clear for ovf/undf flags
Description
1
R/W
ramp_enable
0
Ramp En/rstb
1= enables the CW Ramp Function
2
R/W
ramp_trigg
0
Write always triggers ramps if bit <2> = 0, if bit
<2> = 1, Ramp will not trigger, bit <2> must be
reset to 0 first
3
R/W
ramp_repeat_en
0
Ramp Repeat Seq enable
1= enables autotrigger of ramps
0 = ramp_trigg starts each ramp
4
R/W
ramp_startdir_dn
0
Ramp start direction
1= Start with Ramp Down
0= Start with Ramp Up
5
R/W
ramp_trig_ext_en
0
Enable hardware trigger on GPO3 pin
6
R/W
ramp_singlestep
0
Ramp single step, advances the ramp to the next
step, and holds frequency
7
R/W
ramp_singledir
0
Ramps in one direction only with hop to start at
end of ramp
Table 31. Reg 15h CW Sweep Ramp Step Register
The maximum sweep range is limited to 255 x Fxtal/R
Bit
Type
23:0
R/W
Name
ramp_step
Default
2048
Description
Ramp Step size
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 32. Reg 16h CW Sweep Ramp Step Number Register
The maximum sweep range is limited to 255 x Fxtal/R
Bit
Type
23:0
R/W
Name
ramp_steps_number
Default
2048
Description
Ramp Number of steps in ramp
Table 33. Reg 17h CW Sweep Dwell Time Register
Bit
Type
23:0
R/W
Name
ramp_dwell_time
Default
2048
Description
Ramp Number of cycles to hold at top/bottom
in repeat mode
Table 34. Reg 18h Auxiliary Oscillator Register 1
Type
Name
Default
Description
1:0
R/W
dsmclk_auxclk_insel
0
Selects the input clk for auxclk
0:vcodiv
1:xrefsq or sin
2:refdiv
3:ring oscillator from mono, est 300 MHz to
1 GHz
3:2
R/W
dsmclk_auxclk_modesel
0
0: bypass-no delay
1: pass through w/ delay
2: ring-out constant
3: ring-out seeded/gated
divider selection auxclk value divby
000
001
010
011
100
101
110
111
1
2
4
6
8
10
12
14
6:4
R/W
dsmclk_auxclk_divsel
2
7
R/W
dsmclk_auxclk_sel
0
selects auxclk (if=1) as natural reference clk
input of sigma delta
8
R/W
dsmclk_auxmod_lfsr_en
0
enables 10-bit lfsr inside the delay modulator
(clocked by auxclk or auxclkb)
9
R/W
dsmclk_auxmod_accum_en
0
enables 8-bit accumulator inside the delay
modulator (clocked by auxclk or auxclkb)
11:10
R/W
dsmclk_auxmod_mode
0
delay modulation mode
0: auxmod_lodly_in passthrough
1: accumulator based square-wave
2: lfsr (lo-amp)
3: lfsr (hi-amp)
19:12
R/W
dsmclk_auxmod_fracstep
3
step-size of accumulator (changes square-wave
value once it wraps through 256)
22:20
R/W
dsmclk_auxmod_lodly
0
value of delay-element (when auxmod_mode=0)
or low value used during sq-wave modulation
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Bit
11 - 43
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 35. Reg 19h Auxiliary Oscillator Register 2
Bit
Type
Name
Default
Description
2:0
R/W
dsmclk_auxmod_hidly
7
hi value of delay element during sq-wave
modulation
3
R/W
dsmclk_auxmod_clkinv
1
optionally inverts auxclk as used by the
modulator
4
R/W
dsmclk_auxmod_clkwring
9
select LKD ringosc to clock the LFSR
Table 36. Reg 1Ah Lock Detect Register
Bit
PLL - fractional-n synthesizer - SMT
11
11 - 44
Type
Name
Default
10’d40
Description
threshold count in the timer window to declare
lock (reference cycles)
9:0
R/W
lkd_wincnt_max
10
R/W
lkd_win_asym_enable
0
Enables asymmetric lock detect window (nominal
10nsec)
11
R/W
lkd_win_asym_up_select
0
Sets polarity of the window
12
R/W
lkd_to_sdo_automux_en
0
Muxes the lkd output signal to SDO when SDO is
not being used for Main Serial Port Data Outputs
(Read Operation)
13
R/W
lkd_to_sdo_always
0
Muxes the lkd output signal to SDO always, not
possible to do Main Serial Port Read in this state
14
R/W
lkd_ringosc_mono_select
0
1 select ringosc based oneshot for lock detect
window
0 selects analog based oneshot
16:15
R/W
lkd_ringosc_cfg
0
“00” fastest “11” slowest
18:17
R/W
lkd_monost_duration
0
“00” shortest “11” longest
19
R/W
lkd_ringosc_testmode
0
enables the ring osc by itself for testing
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 37. Reg 1Bh GPO Control Register
Type
Name
gpo_sel
3:0
Default
0
gpo_sel<3:0> = 0000
GPO3 <=gposel_0_data<2>
GPO2 <= gposel_0_data<1>
GPO1 <= gposel_0_data<0>
gpo_sel<3:0> = 0001
GPO3 <= xref_clk_in
GPO2 <= ref_clk_in
GPO1 <= vco_div_clkin
gpo_sel<3:0> = 0010
GP03 <= pfd_up_in
GP02 <= pfd_dn_in
GP01 <= LKD_monost_window
gpo_sel<3:0> = 0011
GP03 <= pfd_sat_ref_in
GP02 <= pfd_sat_vco_div_in
GP01 <= delta_integer_cycslip_sel, this strobe
holds the gain of the PFD at max for anti-cycle
slipping
gpo_sel<3:0> = 0100
GP03 <= xref_clk_in
GP02 <= xref_sin_in
GP01 <= sd_frac_strobe_sync, internally
synchronized frac strobe
gpo_sel<3:0> = 0101
VCO Serial Port Mirror
GPO3 - VSDO
GPO2 = VSCK
GPO1 = SVLE
gpo_sel<3:0> = 0110
GP03 <= SD_Intz1<1>
GP02 <=SD_Intz1<2>
GP01 <= SD_Intz1<3>
3-bit quantized version of the VCO phase
gpo_sel<3:0> = 0111
GP03 <= aux_clk
GP02 <= ringosc_test
GP01 <= clk_SD
gpo_sel<3:0> = 1000
GP03 <= 00
GP02 <= ramp_busy
GP01 <= vcot_busy
R/W
gpo_sel<3:0> = 1001
Not used
gpo_sel<3:0> = 1010
GP03 <= Δ∑ Quantizer Output 3rd lsb
GP02 <= Δ∑ Quantizer Output 2nd lsb
GP01 <= Δ∑ Quantizer Output lsb
this data is driven on gpo if gpo_sel==0
6:4
R/W
gpo_sel_0_data
7
R/W
gpo_dig_drive_en
10:8
R/W
Description
Selects data to be driven on GPO ports
enables Tri-state drivers on GPO output pads
Chip ID 478732 Reserved
0
reserved must write 0 on Chip ID 478732
Chip ID 481502
gpo_ind_drive_dis
0
Chip ID 481502 Only
000 = all GPO pad drivers enabled
xx1 = disable GPO1 pad driver
x1x = disable GPO2 pad driver
1xx = disable GPO3 pad driver
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Bit
11 - 45
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 38. Reg 1Ch Phase Detector CSP Register
Bit
Type
Name
Default
Description
0= Cycle Slip Prevention (CSP) disabled
3:0
PLL - fractional-n synthesizer - SMT
11
11 - 46
R/W
pfds_sat_deltaN
5’d4
4
R/W
pfds_rstb_force
0
5
R/W
pfds_rstb
1
4-bit value to advance or retard phase detector in
VCO cycles if it reaches 2pi , i.e. cycle slip
prevention. 1st bit is polarity, enabled by rstb
CSP PFD Flip-flops RSTB:
1 - controlled by the pfds_rstb bit:
0 - auto-controlled by the CSP logic
Forces the PFD into reset, which tristates charge
pump, freezes charge on the loop filter, and
hence opens the loop
CSP PFD FF rstb
1 - Enables the Cycle Slip Prevention (CSP)
feature of the PFD
Table 39. Reg 1Dh VCO Tune Port Control Register
Bit
Type
Name
Default
Description
0
R/W
voltage_force
0
Selects the source of control of the timing of the
mid-rail voltage,
voltage_force=0 selects Autotune state machine
voltage_force=1 selects voltage_enable from SPI
Used for mid-rail control of VCO during
autotuning
1
R/W
voltage_enable
0
Forces mid-rail voltage on the charge pump
output from the SPI when voltage_force=1
Used for mid-rail control of VCO during
autotuning
Table 40. Reg 1Eh Temperature Sensor Register
Bit
0
Type
R/W
Name
tsens_spi_enable
Default
0
Description
Enable the temperature sensor, draws ~2mA
current, must strobe tsens_spi_strobe Reg 00h
<3>
Table 41. Reg 1Fh LD, VCO & Ramp Busy Read Only Register
Bit
Type
0
RO
ro_lock_detect
Name
Default
0
1 = locked, 0 = unlocked
Description
3:1
RO
ro_dsm_overflow
0
1 = modulator overflow
4
RO
ro_spi_vco_busy
0
Set when VCO autotuning is running
5
RO
ro_ramp_busy
0
Sweeper status flag, set when ramp is busy,
cleared when at end of ramp or not used
Table 42. Reg 20h VCO Tune Caps Read Only Register (vcot)
Bit
5:0
Type
RO
Name
vcot_caps
Default
Description
0
Reads the values of the VCO switched resonator
bank determined by the autotune routine (see )
0 = max VCO freq
63 = min VCO freq
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC701LP6CE
v05.0110
8 GHz 16-BIT FRACTIONAL-N SYNTHESIZER
Table 43. Reg 21h Temperature Sensor Read Only Register
Bit
Type
6:0
RO
Name
Default
tsens_temperature
Description
Current Temperature from temp sensor
lsb = 17.5°C
0000111 = Temp >= 82.5°C
0000110 = Temp
0000000 = Temp <=-22.5°C
tsens_temperature = floor ((Temp+40)/17.5)
0
Table 44. Reg 22h Autotune Result Register
Type
16:0
RO
Name
vcot_cnt
Default
Description
0
Contains the results of the autotune counter
Can be used to calculate the VCO frequency and
optimum VCO setting selected by the autotune
Outline Drawing
NOTES:
1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
6. PAD BURR LENGTH SHALL BE 0.15mm MAX.
PAD BURR HEIGHT SHALL BE 0.25mm MAX.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm
8. ALL GROUND LEADS AND GROUND PADDLE
MUST BE SOLDERED TO PCB RF GROUND.
9. REFER TO HITTITE APPLICATION NOTE
FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
HMC701LP6CE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL Rating
MSL1
[2]
Package Marking [1]
H701
XXXX
[1] 4-Digit lot number XXXX
[2] Max peak reflow temperature of 260 °C
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
PLL - fractional-n synthesizer - SMT
Bit
11 - 47