HMC894LP5E v00.1010 FILTERS - TUNABLE - SMT 3 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Typical Applications Features The HMC894LP5E is ideal for: Fast Tuning Response; 200 ns • Test & Measurement Equipment Excellent Wideband Rejection; >30 dB • Military RADAR & EW/ECM Single Chip Replacement for Mechanically Tuned Designs • SATCOM & Space • Industrial & Medical Equipment 32 Lead 5x5 mm SMT Package General Description Functional Diagram The HMC894LP5E is a MMIC band pass filter which features a user selectable passband frequency. The 3 dB filter bandwidth is approximately 6%. The 20 dB filter bandwidth is approximately 16.5%. The center frequency can be varied between 5.9 and 11.2 GHz by applying an analog tune voltage between 0 and 14V. This tunable filter can be used as a much smaller alternative to physically large switched filter banks and cavity tuned filters. The HMC894LP5E has excellent microphonics due to the monolithic design, and provides a dynamically adjustable solution in advanced communications applications. Electrical Specifications, TA = +25°C, Vfctl = Vbwctl Unless Otherwise Stated Parameter Fcenter Tuning Range Min. Typ. 5.9 3 dB Bandwidth Max. Units 11.2 GHz 6 % Low Side Rejection Frequency (Rejection >20 dB) 0.92*Fcenter GHz High Side Rejection Frequency (Rejection >20 dB) 1.08*Fcenter GHz Re-entry Frequency (Rejection <30 dB) 25 GHz 3 dB Bandwidth Control (Vbwctl) ±3 % Insertion Loss 9 dB Return Loss (2 dB Bandwidth) 7.5 Maximum Input Power for Linear Operation Frequency Control Voltage (Vfctl) 0 Source/Sink Current (Ifctl) Bandwidth Control Voltage (Vbwctl) dB 10 0 Source/Sink Current (Ibwctl) dBm 14 V ±1 mA 14 V ±1 mA Residual Phase Noise [1] (1 MHz Offset) -165 dBc/Hz Fcenter Drift Rate -0.86 MHz/°C Tuning Characteristics [2] tFULLBAND (0% Vfctl to 90% RF) 200 ns [1] Optimum residual phase noise performance requires the use of a low noise driver circuit. [2] Tuning speed is dependent on driver circuit. Data measured with a high speed op-amp driver and includes driver slew rate delay. 3-1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Broadband Insertion Loss vs. Control Voltages, Vfctl = Vbwctl 0 -20 -5 RETURN LOSS (dB) INSERTION LOSS (dB) 0V 7V 14V -30 -40 -50 -10 14V -15 0V -20 S11 S22 -60 7V -70 -25 0 5 10 15 20 25 30 0 FREQUENCY (GHz) 5 10 15 20 25 Insertion Loss vs. Control Voltages, Vfctl = Vbwctl Return Loss vs. Control Voltages, Vfctl = Vbwctl -4 0 -6 0V 7V 14V -5 RETURN LOSS (dB) -8 -10 -12 -14 -16 -10 0V 7V 14V -15 -20 S11 S22 -18 -20 -25 4 6 8 10 12 14 4 FREQUENCY (GHz) 6 8 10 12 14 FREQUENCY (GHz) Insertion Loss vs. Temperature, Vfctl = Vbwctl = 7V Return Loss vs. Temperature, Vfctl = Vbwctl = 7V -2 0 -4 + 25C + 85C - 40C -6 -5 RETURN LOSS (dB) INSERTION LOSS (dB) 30 FREQUENCY (GHz) FILTERS - TUNABLE - SMT 0 -10 INSERTION LOSS (dB) 3 Broadband Return Loss vs. Control Voltages, Vfctl = Vbwctl -8 -10 -12 -14 S11 S22 -10 -15 +25C +85C -40C -20 -16 -18 -25 4 6 8 10 FREQUENCY (GHz) 12 14 4 6 8 10 12 14 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-2 HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz 3 Broadband Return Loss vs. Vbwctl, Vfctl = 7V Broadband Insertion Loss vs. Vbwctl, Vfctl = 7V 0 Vbwctl = 4V Vbwctl = 7V Vbwctl = 10V -20 -5 RETURN LOSS (dB) INSERTION LOSS (dB) -10 -30 -40 -50 Vbwctl=4V -10 Vbwctl=7V -15 S11 S22 -20 -70 -25 0 5 10 15 20 25 30 0 FREQUENCY (GHz) 5 10 20 25 30 Return Loss vs. Vbwctl, Vfctl = 7V Insertion Loss vs. Vbwctl, Vfctl = 7V -2 0 -4 Vbwctl=4V Vbwctl = 4V Vbwctl = 7V Vbwctl = 10V -5 RETURN LOSS (dB) -6 -8 -10 -12 -14 Vbwctl=7V Vbwctl=10V -10 -15 S11 S22 -20 -18 -25 4 6 8 10 12 14 4 FREQUENCY (GHz) 6 8 10 12 14 FREQUENCY (GHz) Center Frequency vs. Temperature, Vfctl = Vbwctl Insertion Loss vs. Temperature, Vfctl = Vbwctl 12 -6 -7 11 INSERTION LOSS (dB) CENTER FREQUENCY (GHz) 15 FREQUENCY (GHz) -16 10 9 8 7 +25C +85C -40C 6 -8 -9 -10 -11 -12 +25C +85C -40C -13 -14 -15 5 -16 0 2 4 6 Vfctl (V) 3-3 Vbwctl=10V -60 INSERTION LOSS (dB) FILTERS - TUNABLE - SMT 0 8 10 12 14 0 2 4 6 8 10 12 14 Vfctl (V) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz 0 8 -2 RETURN LOSS (dB) BANDWIDTH (%) 9 7 6 +25C +85C -40C 5 +25C +85C -40C -4 -6 -8 4 -10 0 2 4 6 8 10 12 14 0 2 4 6 10 12 14 High Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 0.95 1.15 0.93 1.13 F20dB To Fcenter RATIO F20dB TO Fcenter RATIO Low Side Rejection Ratio vs. Temperature, Vfctl = Vbwctl [1] 0.91 0.89 +25C +85C -40C 0.87 8 Vfctl (V) Vfctl (V) 0.85 +25C +85C -40C 3 FILTERS - TUNABLE - SMT Maximum Return Loss in a 2 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 3 dB Bandwidth vs. Temperature, Vfctl = Vbwctl 1.11 1.09 1.07 1.05 0 2 4 6 8 10 12 14 0 Vfctl (V) 2 4 6 8 10 12 14 Vfctl (V) Tuning Sensitivity vs. Temperature, Vfctl = Vbwctl Group Delay, Vctl = Vbwctl 900 2 700 GROUP DELAY (ns) SENSITIVITY (MHz/V) 800 600 500 400 300 200 +25C +85C -40C 100 0 0 2 4 6 Vfctl (V) 8 10 12 14 0V 1.5 14V 7V 1 0.5 0 4 5 6 7 8 9 10 11 FREQUENCY (GHz) 12 13 14 [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to ƒcenter For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-4 HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz 3 Group Delay vs. Fcenter vs. Temperature 3 dB Bandwidth vs. Bandwidth Control 12 + 25C + 85C - 40C 10 BANDWIDTH (%) GROUP DELAY (nS) 1.5 1.4 1.3 1.2 8 6 4 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V 2 1.1 0 0 2 4 6 8 10 12 14 0 2 4 6 Vfctl (V) 10 12 14 Low Side Rejection Ratio vs. Bandwidth Control [1] 0 F20dB TO Fcenter RATIO 1 -5 -10 -15 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V -20 -25 0.95 0.9 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V 0.85 0.8 0 2 4 6 8 10 12 14 0 2 4 Vfctl (V) 6 8 10 12 14 Vfctl (V) High Side Rejection Ratio vs. Bandwidth Control [1] Maximum Return Loss in a 2 dB Bandwidth vs. Bandwidth Control 1.25 0 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V 1.2 Vbwctl=Vfctl Vbwctl=Vfctl +3V Vbwctl=Vfctl -3V -2 RETURN LOSS (dB) F20dB TO Fcenter RATIO 8 Vfctl (V) Insertion Loss vs. Bandwidth Control INSERTION LOSS (dB) FILTERS - TUNABLE - SMT 1.6 1.15 1.1 1.05 -4 -6 -8 1 -10 0 2 4 6 8 10 12 14 0 2 4 Vfctl (V) 6 8 10 12 14 Vfctl (V) [1] Rejection ratio is defined as the ratio of the frequency at which the relative insertion loss is 20 dB to ƒcenter 3-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Input IP3 vs. Power Input Vfctl = Vbwctl 35 25 20 Pin = 0 dBm Pin = 5 dBm Pin = 10 dBm Pin = 15 dBm Pin = 18 dBm 15 10 5.8 6.8 7.8 8.8 9.8 10.8 11.8 FREQUENCY (GHz) Absolute Maximum Ratings 0V + 6.0V + 11V -140 -150 -160 -170 1e+2 1e+3 1e+4 1e+5 1e+6 Reliability Information Junction Temperature to Maintain 1 Million Hour MTTF 150 °C 26 dBm Nominal Junction Temperature (T= 85 °C and Pin = 10 dBm) 90 °C Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Rating (HBM) Class 1B Frequency Control Voltage (Vfctl) -0.5 to +15V Bandwidth Control Voltage (Vbwctl) -0.5 to +15V RF Power Input 1e+7 OFFSET FREQUENCY (Hz) FILTERS - TUNABLE - SMT RESIDUAL PHASE NOISE (dBc/Hz) -130 30 IP3 (dBm) 3 Residual Phase Noise Vfctl = Vbwctl ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-6 HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Outline Drawing FILTERS - TUNABLE - SMT 3 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. Pin BURR LENGTH SHALL BE 0.15mm MAXIMUM. Pin BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish HMC894LP5E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H894 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C 3-7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Pin Number Function Description 1 - 4, 7 - 11, 13 15 - 18, 21 - 32 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 5, 20 GND These pins and exposed paddle must be connected to RF/DC ground. 6 RFIN This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. 12 Vfctl Center frequency control voltage. 14 Vbwctl Bandwidth control voltage. 19 RFOUT This pin is DC coupled and matched to 50 Ohms. External voltage must not be applied to this pin. Interface Schematic FILTERS - TUNABLE - SMT 3 Pin Descriptions Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3-8 HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz Evaluation PCB FILTERS - TUNABLE - SMT 3 List of Materials for Evaluation PCB 128531 [1] Item Description J1, J2 SMA - SRI J3, J4 SMA - Johnson C1, C2 100 pF Capacitor, 0402 Pkg. U1 HMC894LP5E Filter - Tunable PCB [2] 127338 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 25FR 3-9 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC894LP5E v00.1010 FILTER - TUNABLE, BAND PASS SMT 5.9 - 11.2 GHz 3 FILTERS - TUNABLE - SMT Notes: For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 3 - 10