Push-Pull Complete Locking Coaxial Connectors (PC Card Type 2 Mountable) POD3 Series Board Mounting Example ■Features 1. Excellent push-pull complete locking method for ease of operation The connector coupling portion uses a Hirose Electric original push-pull complete locking system. 1) A sure lock is obtained by holding the connector outside tube portion and just giving it a light push. 2) Positive lock prevents easy disconnection. To remove the connector, just hold the connector outside tube portion and pull for a simple release of the lock 2. Type II PC Card Mountable The receptacle thickness is 3.9 mm which permits mounting to the back side of a type II card. (Note) that at the time of card mounting, use of 0.3mm offset of the board mounting surface from the card center line will result in the same card center axis and connector center axis. 3. High Degree of Matching The top-touch system used for the coupling method achieves high frequency performance from 0 to 3 GHz with a V.S.W.R. of 1.3 or less. 4. Ultra-Miniature ■Applications Wireless LAN cards, GPS cards, and miniature wireless communications devices. ■Function Diagrams Jack Side As a complete locking type, this series achieves a size reduction of approximately 50% in the direction of the diameter as compared to our original POD1 Series. 5. Accommodates Ultra-Fine Cable These connectors accommodate the use of ultra-fine coaxial Teflon cable which permits high-density wiring inside equipment. Ø1.48 (single-layer shielded cable) ....CO-6F FH-SB manufactured by Hitachi Cable, Ltd. ....DFS111-UL1979 manufactured by Junkosha Co., Ltd. ■Jack POD3-J-DFS111 Plug Side ■Plug Receptacle ■Receptacle POD3-PR-1 POD3-R-1 ■Conversion Adapter ■Conversion Adapter (Coupling portion: SMA side jack - POD3 side jack) (Coupling portion: SMA side jack - POD3 side plug) HRMJ-POD3J HRMJ-POD3P B23 ■ Product Specifications Nominal characteristic impedance 50 ohms Voltage 100 V AC Frequency DC to 3 GHz Ratings Item Operating temperature Operating humidity Specification -30C° to +85C° 95% max. Condition 1. Contact resistance Inner : 10 m ohms max. Outside: 5 m ohms max. 100 mA max. 2. Insulation resistance 500 M ohms min. 250 V DC 3. Withstanding voltage No flashover or insulation breakdown. 300 V AC / 1 minute 4. V.S.W.R.(*) 1.3 max. DC to 3 GHz 5. Female contact retention 0.2 N min. Measured with a Ø0.3 pin gauge 6. Insertion and withdrawal force (plug) 1.96 N min. With corresponding connector 7. Durability (Insertion/withdrawal) Contact resistance: Amount of change 10 m ohms max. 250 cycles 8. Vibration No electrical discontinuity of 1µs or more No damage, cracks, or parts looseness. Frequency: 10 to 500 Hz, single amplitude of 0.75 mm or acceleration of 98 m/s2(peak), 2 hours in each of the 3 directions. 9. Shock No electrical discontinuity of 1µs or more No damage, cracks, or parts looseness. Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 10 cycles in each of the 3 axis 10. Humidity (Steady state) Insulation resistance 100 M ohms min. (at high humidity) 500 M ohms min. (when dry) No damage, cracks, or parts looseness. 240 hours at temperature of 25ç to 65ç and humidity of 90% to 96% 11. Temperature cycle No damage, cracks, or parts looseness. Temperature: -55°C → 5 to 35°C → 85°C → 5 to 35°C Time: 30 min → Within 5 min → 30 min. → Within 5 min Cycles: 5 12. Salt spray No marked corrosion Exposed to density 5% salt water for 48 hours *Voltage standing wave ratio (V.S.W.R.) measuring system. The above voltage standing wave ratio (V.S.W.R.) standard value is measured in the measuring system as shown below. Network Analyzer Test Set Test Port Note1: The cable connector is measured with double ended 10cm cable assembly. Note2: The printed circuit board connector is mounted on the 50 ohms PCB, to which Hirose's adaptor is connected. D.U.T Termination Test Port Cable ■Materials part Material Finish Body Brass/Phosphor bronze Gold and nickel plating/Gold plating Insulator PTFE —————— Female inner contact Beryllium copper Gold plating Male vinnerr contact Phosphor bronze Gold plating Spring coil Piano wire Nickel plating Heat-shrink tubing Polyolefin —————— ■ Ordering Information POD3 – [ q q Series name: POD3 w Connector types J : Jack R : Receptacle PR : Plug receptacle B24 ] – [ w ] e e Applicable cable or suffix DFS111: CO-6F FH-SB manufactured by Hitachi Cable, Ltd. DFS111-UL1979 manufactured by Junkosha Co., Ltd. Ø3.8 ■Jack 11 CL No. Part Number 327-0152-2 POD3-J-DFS111 ■Receptacle Ø0.6 3.9 Ø3.5 5 0.6 7 3.5 8.3 CL No. Part Number 327-0154-8 POD3-R-1 ■Plug Receptacle Ø0.6 3.9 Ø3.85 5 0.6 6.7 3.9 8 CL No. Part Number 327-0153-5 POD3-PR-1 ■Conversion Adapter ●SMA conversion adapter (Coupling portion: SMA side jack - POD3 side plug) 13.9 Ø3.85 1/4-36UNS-2A 9.5 8HEX CL No. Part Number 311-0285-0 HRMJ-POD3P ●SMA conversion adapter (Coupling portion: SMA side jack - POD3 side jack) 14.2 Ø3.5 1/4-36UNS-2A 9.5 8HEX CL No. Part Number 311-0286-3 HRMJ-POD3J B25 ■Connector Mounting Condition 5Max 3.9 0.3 The mounting reference diagram is an anticipated diagram of the condition of mounting to a frame offset 0.3 mm from the card center line. PCB ■PCB mounting pattern (7.5) 6 (Ø 0.5 through hole) 4 (2) 3.5 (1) 4 +0.1 +0 2 1min Corner escape portion Pad B26 Copper foil portion (Resist layer beyond the pad)