PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST TITLE : HV089WX1-100 HV089WX1 100 Product Specification for Customer Rev. O FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com BOE HYDIS TECHNOLOGY SPEC. NUMBER B2005-C001-B (1/3) PRODUCT GROUP TFT-LCD REV. O ISSUE DATE 2008.2. 11 PAGE 1 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008.2.11 REVISION HISTORY REV. ECN NO. O SPEC. NUMBER B2005-C001-B (2/3) DESCRIPTION OF CHANGES Initial Release DATE PREPARED 2008.02.11 Joseph Ha SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 2 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 Contents No Item Page 1.0 General Description 4 2.0 Absolute Maximum ratings 6 3.0 Electrical specifications 7 4.0 Optical specifications 9 5.0 Interface Connection 14 6.0 Signal Timing Specification 17 7.0 Signal Timing waveforms of interface signal (DE mode) 17 8.0 Input Signals, Display Colors & Gray Scale of Colors 19 9.0 Power Sequence 20 10.0 Mechanical Characteristics 21 11.0 Mechanical Drawing 22 12.0 Reliability Test 24 13.0 Handling & Cautions 24 14.0 Environment & Safety 26 15.0 Packing Information 28 SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 3 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 1.0 GENERAL DESCRIPTION 1.1 Introduction HV089WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 8.9 inch diagonally measured active area with WXGA resolutions (1280 horizontal by 768 vertical pixel array) array). Each pixel is divided into RED RED, GREEN GREEN, BLUE dots which are arranged in vertical stripe and this module can display 262,144 colors. The TFT-LCD panel used for this module is a low reflection and higher color type. LVDS Input Si Signal l LCDS Rx + T/CON DC/DC Gamma Vcom Gate Driver 1 (C Connector CN VDD Source Driver TFT LCD Panel BACK LIGHT (Fluorescent Lamp) 1280 X 768 1 ) HVDD VDIM Back Light (SMD LED Array) CN2 1.2 Features z z z z z z z z z z Thin and light weight 3.3 V power supply Low driving voltage and low power consumption 1 Channel LVDS Interface SMD LED (36EA) Array (Top Side/Horizontal Direction) 262,144 colors Data enable signal mode Front Mounting Frame RoHS Product No EDID and No LED driver SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 4 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 1.3 Application z Tablet PC 1.4 General Specifications <Table T bl 1. 1 General G l Specifications> S ifi ti Parameter Specification Active area 193.92 (H) ×116.35 (V) Number of pixels 1280 (H) ×768 (V) Pixel pitch 0.1515 (H) ×0.1515 0.1515 (V) Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Dimensional outline 206.6±0.3(W) ( ) ×133.0±0.3(V) ( ) × 5.25 ((D/Max) / ) Luminance of White 300 (Typ.) Weight 130(Typ.) ± 5 (Min. / Max.) Back-light SMD LED (36EA) Array Unit Remarks mm pixels mm colors mm Note 1 Cd/m² At Center g Note 1: at PCB side SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 5 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. Ta=25+/-2°C Parameter Symbol Min. Max. Unit L i Power Logic P Supply S l Voltage V l VDD -0.3 03 40 4.0 V Logic Power Supply Voltage VIN -0.3 VDD+0.3 V HVDD -0.3 40 V 25℃ ILED - 30 mA 50℃ ILED - 20 mA Back-light LED Reverse Voltage VR - 5 V Operating Temperature TOP 0 +50 ℃ Storage Temperature TSP -20 +60 ℃ Back-light Power Supply Voltage Back-light LED Current Remarks Note 1 Note 1, 2 Note 1. 1 Ambient temperature vs allowable forward current are shown in the figure below. below Note 2. Temperature and relative humidity range are shown in the figure below. 90% RH Max. ( 40℃ ≥ Ta) Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation. Relative Humudity 100 Ambient Temperature vs Maximum Forward Current (40, 90) 90 80 60 (50,20) Operating p g Range g (50, 50) 40 (60, 27) 20 Storage Range 5 -40 -20 0 20 40 60 80 Temperature (℃) SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 6 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 3.0 ELECTRICAL SPECIFICATIONS 3.1 Electrical Specifications < Table 3. Electrical Specifications > Parameter Min. Typ. Max. Unit Remarks Logic Power Supply Voltage VDD 3.0 3.3 3.6 V Note 1 Logic Power Supply Current IDD - 330 500 mA Note 1 Back-light Anode Supply Voltage Vanode - 19.2 25.8 V Note 2 Back-light Cathode Supply Voltage Vcathode - 0 4.8 V Note 2 Back-light g PWM Frequency q y FPWM 100 - 500 ㎐ High Level Differential Input Signal Voltage VIH - - +100 mV Low Level Differential Input Signal Voltage VIL -100 - - mV Back-light LED Voltage / Back-light LED Total Voltage VLED /VBL 2.7/ 16.2 16 2 3.2/ 19.2 19 2 3.5/ 21.0 21 0 V Back-light LED Current / Back-light LED Total Current ILED /IBL 15.2/ 91.2 16/ 96 16.8/ 100.8 mA 12,000 - - Hrs PD - 1.09 1.65 W Note 1 PLED - 1 84 1.84 2 12 2.12 W Note 2 2, 3 Ptotal - 2.84 3.77 W Note 1, 2, 3 PEBL - 1.46 1.51 W Note 1, 2, 3 Life Time Power Consumption Power Consumption (EBL) VCM = +1.2V Based on LED Notes : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for 3.3V at 25℃. a)) Typ : Window d XP pattern b) Max : Vertical Sub line pattern c) EBL : Mosaic pattern (32 x 32) 2. The power supply voltage and current is measured and specified at the interface connector of LCM including LED Driver. 3. Reference value, which is measured with LED Driver for 12V. 4. Reference value, which is measured without LED Driver. 5. Calculated value for reference (VLED × ILED × # of LEDs (36EA) ). SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 7 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE O 2008. 2.11 TFT-LCD PRODUCT 4.0 OPTICAL SPECIFICATION 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØØ=270 270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25°C. Optimum viewing angle direction is 6 o’clock. 4.2 Optical Specifications <Table 4. Optical Specifications> Parameter Viewing Angle range Symbol Horizontal Vertical Min. Typ. Max. Unit 85 89 90 Deg. 85 89 90 Deg. 85 89 90 Deg. 85 89 90 Deg. 450 500 - 270 300 - 80 85 - 60 70 - 0.260 0.300 0.340 0.280 0.320 0.360 xR 0.523 0.563 0.603 yR 0.314 0.354 0.394 0.291 0.331 0.371 0 502 0.502 0 542 0.542 0 582 0.582 xB 0.106 0.146 0.186 yB 0.077 0.117 0.157 Ta= 25° C Θ = 0° - 28 - ms Note 5 Θ = 0° - - 2.0 % Note 6 Θ3 Θ9 Θ12 CR Luminance of White 1 Point Yw 5 Points ΔY5 13 Points ΔY13 White Chromaticity Red Reproduction Of color Green xw yw xG yG Blue Response Rise Tr Time Decay Td Cross Talk SPEC. NUMBER B2005-C001-B (3/3) CR > 10 Θ6 Luminance Contrast ratio White Luminance uniformity Condition CT Θ = 0° Θ = 0° Θ = 0° Θ = 0° SPEC. TITLE HV089WX1-100 Product Specification for Customer Remark Note 1 Note 2 cd/m2 % Note 3 Note 4 PAGE 8 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 Note : 1. 2. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. ( see FIGURE 1 shown in Appendix ) Contrast measurements shall be made at viewing angle of Θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = 3. 4 4. 5. 6. Luminance when displaying a white raster Luminance when displaying a black raster The White luminance uniformity on LCD surface is then expressed as : ΔY = Maximum Luminance of 5(or 13) points / Minimum Luminance of 5(or 13) points. ( see FIGURE 2 shown in Appendix ) The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal OFF and ON. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the h luminance l i (YA) off a 25mm 25 di diameter area, with i h allll display di l pixels i l set to a gray level, l l to the luminance (YB) of that same area when any adjacent area is driven dark. ( see FIGURE 4 shown in Appendix ) SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 9 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 4.3 Optical Measurements Figure 1. Measurement Set Up Photo detector ( TOPCON BM-5A) o Field = 1 50 cm TFT-LCD module LCD panel Center of the screen Optical characteristics measurement setup Figure 2. White Luminance and Uniformity Measurement Locations (5 points) Column 320 640 960 Row 192 384 576 Note 4. N 4 Luminance of white is defined as luminance values of 5 points across the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in Figure 2 for a total of the measurements per display. * Yw = (Sum of 5 Points Luminance / 5 ) * LED Condition = (Duty Ratio 100%, LED current 16.0mA) SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 10 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 Figure 3. 3 Uniformity Measurement Locations (13 points) 192 384 576 Note 5. The White luminance uniformity on LCD surface is then expressed as : ΔY5 = (Minimum Luminance of five points / Maximum Luminance of five points) X 100% (see Figure 2) , ΔY13 = (Minimum Luminance of 13 points /Maximum Luminance of 13 points) X 100% (see Figure 3). Figure g 4. Response p Time Testing g TFT Off(Black) TFT On(White) Tr TFT Off(Black) Td 100% 90% 10% 0% SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 11 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 Figure 5. Cross Modulation Test Description VIEW AREA VIEW AREA 320,192 960,192 L31 YB(1120, 384) 320,576 L0 YA (1120, 384) Cross-Talk (%) = 960,576 YB - YA YB × 100 Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns Note 6. The electro-optical response time measurements shall be made as Figure 4 by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Tr, and 90% to 10% is Td. Note 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark (Refer to Figure 5). SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 12 OF 27 A4(210 X 297) 5.0 PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 INTERFACE CONNECTION. 5.1 Electrical Interface Connection <Table 5. Pin Assignments for the Interface Connector> CN1 Interface connector I-PX / 20347-030E-02 or equivalent CN2 FPC connector I-PEX / 20397-008E or equivalent Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 SPEC. NUMBER B2005-C001-B (3/3) Symbol VDD1 VDD2 VDD3 VDD4 NC VSS VSS VSS VSS RIN0RIN0+ 0 VSS RIN1RIN1+ VSS RIN2RIN2+ VSS RCLKINRCLKIN+ VSS NC VCD1 VCD2 VCD3 VCD4 VCD5 VCD6 NC VAD Function +3.3V +3.3V +3.3V +3.3V Power Supply: Power Supply: Power Supply: Power Supply: Reserved Ground Ground Ground Ground LVDS Negative data signal (-) LVDS S Positive os t e data ssignal g a ((+)) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative data signal (-) LVDS Positive data signal (+) Ground LVDS Negative clock signal (-) LVDS Positive clock signal (+) Ground Reserved LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode LED Power Cathode Reserved LED Power Anode SPEC. TITLE HV089WX1-100 Product Specification for Customer Remark Tx pin # 48 Tx p pin # 47 Tx pin # 46 Tx pin # 45 Tx pin # 42 Tx pin # 41 Tx pin # 40 Tx pin # 39 PAGE 13 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 5.2. LVDS Interface LVDS Transmitter: THC63LVDM83A or equivalent. Input signal Transmitter Pin No R0 51 R1 52 R2 54 R3 55 R4 56 R5 3 G0 4 G1 6 G2 7 G3 11 G4 12 G5 14 B0 15 B1 19 9 B2 20 B3 22 B4 23 B5 24 HSYNC 27 VSYNC 28 DE 30 MCLK 31 SPEC. NUMBER B2005-C001-B (3/3) Pin No Interface DF19KR-20P-1H System (Tx) TFT-LCD (Rx) Pin No. 48 47 OUT0OUT0+ IN0IN0+ 10 11 46 45 OUT1OUT1+ IN1IN1+ 13 14 42 41 OUT2OUT2+ IN2IN2+ 16 17 40 CLKOUT- CLKIN- 19 39 CLKOUT+ CLKOUT CLKIN+ CLKIN 20 SPEC. TITLE HV089WX1-100 Product Specification for Customer Remark PAGE 14 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 5.3 Back-light g Interface CN2 LED FPC Connector (20397-008E, Manufactured by I-PEX ) Pin No. Symbol Function 1 Anode1 LED Anode Power Supply 2 Anode2 LED Anode Power Supply 3 Anode3 LED Anode Power Supply 4 Anode4 LED Anode Power Supply 5 NC 6 Cathode1 LED Cathode Power Supply 7 Cathode2 LED Cathode Power Supply 8 Cathode3 LED Cathode Power Supply 9 Cathode4 LED Cathode Power Supply Remark LED Anode Power Supply pp y (3.2V X 6 EA = 19.2V) Non-Connection LED Cathode Power Supply 5.4. Data Input Format (1,1) (1,2) (1279,1) (1280,1) R G B R G B R G B R G B 1 Pixel = 3 Dots R G B R G B R G B (1,768) (2,768) SPEC. NUMBER B2005-C001-B (3/3) R G B R G B Display position of input data (1279,768) (1280,768) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 15 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 6 0 SIGNAL TIMING SPECIFICATIONS 6.0. 6.1 HV089WX1-100 is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Symbols Min Typ Max Unit Frame Period T1 804 823 - lines Vertical Display Period T2 - 768 - lines One Line Scanning Period T3 1350 1440 - clocks Horizontal Display Period T4 - 1280 - clocks 1/T5 - 71.11 - MHz Clock Frequency 7.0 SIGNAL TIMING WAVEFORMS 7 1 Timing Waveforms of Interface Signal 7.1 T1 T2 DE T3 DCLK T5 DE DATA SIGNALS SPEC. NUMBER B2005-C001-B (3/3) T4 Valid display data (1280 Clocks) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 16 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 7.2 LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter < LVDS Rx Interface Timing Specification> Item Symbol Min. Typ. Max. Unit Remarks CLKIN P Period i d tRCIP 12 50 12.50 14 43 14.43 25 00 25.00 nsec Input Data 0 tRIP0 -0.4 0.0 +0.4 nsec Input Data 1 tRIP1 tRICP/7-0.4 tRICP/7 tRICP/7+0.4 nsec Input Data 2 tRIP2 2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec Input Data 3 tRIP3 3 ×tRICP/7-0.4 ×tRICP/7 0 4 3 ×tRICP/7 3 ×tRICP/7+0.4 ×tRICP/7+0 4 nsec Input Data 4 tRIP4 4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec Input Data 5 tRIP5 5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec Input Data 6 tRIP6 6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 tRIP1 tRIP0 RxINz +/* Z = 0, 1, 2 RxCLKIN+/- Rx Rx Rx Rx Rx Vdiff=0[v] Rx Rx Rx Rx Rx Rx Vdiff=0[v] tRCIP SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 17 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of 262,144 colors are derived from the resultant 18 bit data. Colors & Gray Scale Basic Colors Gray Scale Of Red Gray Scale Of Green Gray Scale Of Blue Gray Scale Of White & Black Red Data R5 R4 R3 R2 Green Data R1 R0 G5 G4 G3 G2 Blue Data G1 G0 B5 B4 B3 B2 B1 B0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Darker 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 △ ↓ ▽ ↓ ↓ ↓ ↓ ↓ Brighter 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ▽ 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Darker 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 △ ↓ ▽ ↓ ↓ ↓ ↓ ↓ Brighter 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 ▽ 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 G Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Darker 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 △ ↓ ▽ Brighter ↓ ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 ▽ 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 △ 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 Darker 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 △ ↓ ↓ ▽ ↓ ↓ ↓ ↓ Brighter 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0 1 ▽ 1 1 1 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 18 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 9.0 POWER SEQUENCE Q To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below 0 9VDD 0.9VDD Power Supply 0V 0.9VDD 0.1VDD 0.1VDD T1 T5 T7 T2 T6 Interface Signal Valid 0V T3 Back- light z z z z z z z T4 0V 0 < T1 ≤ 10 ms 0 < T2 ≤ 50 ms 200 ms ≤ T3 200 ms ≤ T4 0 ≤ T5 ≤ 50ms 0 ≤ T6 ≤ 10ms 150ms ≤ T7 Notes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light g must be turn on after power p for logic g and interface signal g are valid. SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 19 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements FIGURE 5, 6 shown in appendix shows mechanical outlines for the model. Parameter Specification Active area 193.92 (H) ×116.35 (V) Number of pixels 1280(H) ×768(V) Unit mm pixels (1 pixel = R + G + B dots) Pixel pitch 0.1515(H) ×0.1515(V) Pixel arrangement RGB Vertical stripe Display colors 262,144 Display mode Normally Black Dimensional outline 206.6±0.3(W) ×133.0±0.3(V) × 5.25 (D/Max) Weight 130 (Typ.) Back-light SMD LED (36ea) Array mm colors mm g 10.2 Mounting See FIGURE 5. (shown in Appendix) 10.3 Glare and Polarizer Hardness. The surface of the LCD has an glare coating and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50 cm from the screen with an overhead light level of 150lux. The manufacture shall furnish limit samples of the panel showing the light leakage acceptable. SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 20 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 11.0 Mechanical Drawing Figure 6. TFT-LCD Module Outline Dimension (Front View) SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 21 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 Figure 7. TFT TFT-LCD LCD Module Outline Dimensions (Rear view) 0 1 SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 22 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 12.0 RELIABLITY TEST The Reliability test items and its conditions are shown in below. <Table 12. Reliability Test> No Test Items Conditions 1 High temperature storage test Ta = 60 °C, C, 240 hrs 2 Low temperature storage test Ta = -20 °C, 240 hrs 3 High temperature & high humidity operation test Ta = 50 ℃, 80%RH, 240hrs 4 High temperature operation test Ta = 50 °C, 240 hrs 5 Low temperature operation test Ta = 0 °C, 240 hrs 6 Thermal shock Ta = -20 °C ↔ 60 °C (30 min), 100 cycle 7 Vibration test (non-operating) Frequency : 10~500Hz Gravity/AMP : 1.5G Period : X,Y,Z 30min 8 Shock test (non-operating) Gravity : 220G Pulse width : 2ms, half sine wave ±X, ±Y, ±Z Once for each direction 9 Electro-Static Discharge Test (non operating) (non-operating) Air : 150pF, 330ohm, 15KV Contact : 150pF 150pF, 330ohm 330ohm, 8KV SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 23 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 13.0 HANDLING & CAUTIONS 13.1 Cautions when taking out the module y Pick the pouch only, when taking out module from a shipping package. 13.2 Cautions for handling the module y As the electrostatic discharges may break the LCD module module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. y As the LCD panel and backlight element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. 13.3 Cautions for the operation y When the module is operating, do not lose MCLK, DE signals. If any one of these signals were lost, the LCD panel would be damaged. y Obey the supply voltage sequence. If wrong sequence were applied, the module would be damaged. 13.4 Cautions for the atmosphere y Dewdrop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. t h St Storage iin an electro-conductive l t d ti polymer-packing l ki pouch h and d under d relatively low temperature atmosphere is recommended. 13.5 Cautions for the module characteristics y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking. 13.6 Other cautions y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. y When returning the module for repair or etc, please pack the module not to be broken. We recommend using the original shipping packages. SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 24 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 14.0 Environment & Safety 14.1 Packing Label Label Size: 108 mm (L) × 56 mm (W) Contents Model: HV089WX1-100 Q`ty: Module Q`ty in one box Serial No.: Box Serial No. See next figure for detail description. Date: Packing Date FG Code: FG Code of Product XX HV089WX1-100 * 0000000000000 * 200X.X.XX XXXX 00 0 00 0 0 000000 Type Grade Year Month ITEM-CODE Serial_no SPEC. NUMBER B2005-C001-B (3/3) FG CODE RoHS Mark SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 25 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 14.3 Product Label 0 1 BOE HYDIS Barcode 1 X X 2 3 4 5 X X X X 6 X 7 X X X X X X X X No 1. Control Number No 5. Month (1, 2, 3,…, 9, X, Y, Z) No 2. Rank / Grade No 6. Product name No 3. Line Classification No 7. Serial Number (BOE HYDIS : H, LCM : L, BOE OT : A/B/C) No 4. Year (7 : 2007, 8 : 2008, …) SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 26 OF 27 A4(210 X 297) PRODUCT GROUP REV ISSUE DATE TFT-LCD PRODUCT O 2008. 2.11 15.0 PACKING INFORMATION 15.1 Packing Order Put silica gels in the box. Put Pad into the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. As shown in the figure, f place the Modules bundled by shielding bag in the box. Notes y Box Dimension : 261mm(W) X 349mm(D) X 311mm(H) y Package P k Q Quantity tit iin one Box B : 20 20pcs SPEC. NUMBER B2005-C001-B (3/3) SPEC. TITLE HV089WX1-100 Product Specification for Customer PAGE 27 OF 27 A4(210 X 297)