64Mx72 bits PC133 SDRAM Registered DIMM with PLL, based on 64Mx4 SDRAM with LVTTL, 4 banks & 8K Refresh HYM72V64C736B(L)T4 Series DESCRIPTION The HYM72V64C736B(L)T4 Series are 64Mx72bits ECC Synchronous DRAM Modules. The modules are composed of eighteen 64Mx4bits CMOS Synchronous DRAMs in 400mil 54pin TSOP-II package, one 2Kbit EEPROM in 8pin TSSOP package on a 168pin glass-epoxy printed circuit board. One 0.22uF and one 0.0022uF decoupling capacitors per each SDRAM are mounted on 512Mbytes memory. The HYM72V64C736B(L)T4 Series are fully synchronous operation referenced to the positive edge of the clock . All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. FEATURES • PC133/PC100MHz support • SDRAM internal banks : four banks • 168pin SDRAM Unbuffered DIMM • Module bank : one physical bank • Serial Presence Detect with EEPROM • Auto refresh and self refresh • 1.7” (43.18mm) Height PCB with double sided components • 8192 refresh cycles / 64ms • Programmable Burst Length and Burst Type • Single 3.3±0.3V power supply • All device pins are compatible with LVTTL interface • Data mask function by DQM - 1, 2, 4 or 8 or Full page for Sequential Burst - 1, 2, 4 or 8 for Interleave Burst • Programmable CAS Latency ; 2, 3 Clocks ORDERING INFORMATION Part No. Clock Frequency Internal Bank Ref. HYM72V64C736BT4-K HYM72V64C736BT4-H HYM72V64C736BLT4-K HYM72V64C736BLT4-H Power SDRAM Package Plating TSOP-II Gold Normal 133MHz 4 Banks 8K Low Power This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any responsibility for use of circuits described. No patent licenses are implied. Rev. 0.3/Jan. 02 1 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series PIN DESCRIPTION PIN PIN NAME DESCRIPTION CK0~CK3 Clock Inputs The system clock input. All other inputs are registered to the SDRAM on the rising edge of CLK CKE0 Clock Enable Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh /S0, /S2 Chip Select Enables or disables all inputs except CK, CKE and DQM BA0, BA1 SDRAM Bank Address Selects bank to be activated during /RAS activity Selects bank to be read/written during /CAS activity A0 ~ A12 Address Row Address : RA0 ~ RA12, Column Address : CA0 ~ CA9, CA12 Auto-precharge flag : A10 /RAS, /CAS, /WE Row Address Strobe, Column Address Strobe, Write Enable /RAS, /CAS and /WE define the operation Refer function truth table for details REGE Register Enable Register Enable pin which permits the DIMM to operateion in Buffered Mode when REGE input is Low, in Registered Mode when REGE input is High DQM0~DQM7 Data Input/Output Mask Controls output buffers in read mode and masks input data in write mode DQ0 ~ DQ63 Data Input/Output Multiplexed data input / output pin CB0 ~ CB7 Check Bit Input/Output Check bits for ECC VCC Power Supply (3.3V) Power supply for internal circuits and input buffers VSS Ground Ground SCL SPD Clock Input Serial Presence Detect Clock input SDA SPD Data Input/Output Serial Presence Detect Data input/output SA0~2 SPD Address Input Serial Presence Detect Address Input WP Write Protect for SPD Write Protect for Serial Presence Detect on DIMM NC No Connection No connection Rev. 0.3/Jan. 02 2 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series PIN ASSIGNMENTS FRONT SIDE PIN NO. BACK SIDE NAME PIN NO. NAME FRONT SIDE PIN NO. NAME BACK SIDE PIN NO. NAME *CK1 1 VSS 85 VSS 41 VCC 125 2 DQ0 86 DQ32 42 CK0 126 A12 3 DQ1 87 DQ33 43 VSS 127 VSS 4 DQ2 88 DQ34 44 NC 128 CKE0 5 DQ3 89 DQ35 45 /S2 129 NC 6 VCC 90 VCC 46 DQM2 130 DQM6 7 DQ4 91 DQ36 47 DQM3 131 DQM7 8 DQ5 92 DQ37 48 NC 132 NC 9 DQ6 93 DQ38 49 VCC 133 VCC 10 DQ7 94 DQ39 50 NC 134 NC 51 NC 135 NC 52 CB2 136 CB6 Architecture Key 11 DQ8 95 DQ40 53 CB3 137 CB7 12 VSS 96 VSS 54 VSS 138 VSS 13 DQ9 97 DQ41 55 DQ16 139 DQ48 14 DQ10 98 DQ42 56 DQ17 140 DQ49 15 DQ11 99 DQ43 57 DQ18 141 DQ50 16 DQ12 100 DQ44 58 DQ19 142 DQ51 17 DQ13 101 DQ45 59 VCC 143 VCC 18 VCC 102 VCC 60 DQ20 144 DQ52 19 DQ14 103 DQ46 61 NC 145 NC 20 DQ15 104 DQ47 62 NC 146 NC 21 CB0 105 CB4 63 NC 147 REGE 22 CB1 106 CB5 64 VSS 148 VSS 23 VSS 107 VSS 65 DQ21 149 DQ53 24 NC 108 NC 66 DQ22 150 DQ54 25 NC 109 NC 67 DQ23 151 DQ55 26 VCC 110 VCC 68 VCC 152 VCC 27 /WE 111 /CAS 69 DQ24 153 DQ56 28 DQM0 112 DQM4 70 DQ25 154 DQ57 29 DQM1 113 DQM5 71 DQ26 155 DQ58 30 /S0 114 NC 72 DQ27 156 DQ59 31 NC 115 /RAS 73 VCC 157 VCC 32 VSS 116 VSS 74 DQ28 158 DQ60 33 A0 117 A1 75 DQ29 159 DQ61 34 A2 118 A3 76 DQ30 160 DQ62 35 A4 119 A5 77 DQ31 161 DQ63 36 A6 120 A7 78 VSS 162 VSS 37 A8 121 A9 79 CK2 163 *CK3 38 A10/AP 122 BA0 80 NC 164 NC 39 BA1 123 A11 81 WP 165 SA0 40 VCC 124 VCC 82 SDA 166 SA1 83 SCL 167 SA2 84 VCC 168 VCC Voltage Key Note : * CK1 ~ CK3 are connected with termination R/C (Rsfer to the block diagram) Rev. 0.3/Jan. 02 3 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series BLOCK DIAGRAM Note : 1. The serial resistor values of DQs are 10ohms 2. The padding capacitance of termination R/C for CK1~CK3 is 12pF Rev. 0.3/Jan. 02 4 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series SERIAL PRESENCE DETECT BYTE NUMBER FUNCTION DESCRIPTION FUNCTION VALUE -H -K -H -K BYTE0 # of Bytes Written into Serial Memory at Module Manufacturer 128 Bytes 80h BYTE1 Total # of Bytes of SPD Memory Device 256 Bytes 08h BYTE2 Fundamental Memory Type BYTE3 SDRAM 04h # of Row Addresses on This Assembly 13 0Dh BYTE4 # of Column Addresses on This Assembly 11 0Bh BYTE5 # of Module Banks on This Assembly 1 Bank 01h BYTE6 Data Width of This Assembly 72 Bits 48h BYTE7 Data Width of This Assembly (Continued) - 00h BYTE8 Voltage Interface Standard of This Assembly BYTE9 SDRAM Cycle Time @/CAS Latency=3 7.5ns 7.5ns 75h 75h BYTE10 Access Time from Clock @/CAS Latency=3 5.4ns 5.4ns 54h 54h BYTE11 DIMM Configuration Type LVTTL ECC 02h 7.8125us / Self Refresh Supported 82h Refresh Rate/Type BYTE13 Primary SDRAM Width x4 04h BYTE14 Error Checking SDRAM Width x4 04h BYTE15 BYTE16 Burst Lenth Supported BYTE17 # of Banks on Each SDRAM Device tCCD = 1 CLK 01h 1,2,4,8,Full Page 8Fh 4 Banks 04h /CAS Latency=2,3 06h BYTE18 SDRAM Device Attributes, /CAS Lataency BYTE19 SDRAM Device Attributes, /CS Lataency /CS Latency=0 01h BYTE20 SDRAM Device Attributes, /WE Lataency /WE Latency=0 01h BYTE21 SDRAM Module Attributes Registered/Buffered inputs, with PLL 1Fh SDRAM Device Attributes, General +/- 10% voltage tolerence, Burst Read Single Bit Write, Precharge All, Auto Precharge, Early RAS Precharge 0Eh BYTE22 1 01h BYTE12 Minimum Clock Delay Back to Back Random Column Address 2 BYTE23 SDRAM Cycle Time @/CAS Latency=2 7.5ns 10ns 75h A0h BYTE24 Access Time from Clock @/CAS Latency=2 5.7ns 6ns 54h 60h BYTE25 SDRAM Cycle Time @/CAS Latency=1 - - 00h 00h BYTE26 Access Time from Clock @/CAS Latency=1 - - 00h 00h BYTE27 Minimum Row Precharge Time (tRP) 15ns 20ns 0Fh 14h BYTE28 Minimum Row Active to Row Active Delay (tRRD) 15ns 15ns 0Fh 0Fh BYTE29 Minimum /RAS to /CAS Delay (tRCD) 15ns 20ns 0Fh 14h BYTE30 Minimum /RAS Pulse Width (tRAS) 45ns 45ns 2Dh 2Dh BYTE31 Module Bank Density BYTE32 Command and Address Signal Input Setup Time 1.5ns 1.5ns 15h 15h BYTE33 Command and Address Signal Input Hold Time 0.8ns 0.8ns 08h 08h BYTE34 Data Signal Input Setup Time 1.5ns 1.5ns 15h 15h BYTE35 Data Signal Input Hold Time 0.8ns 0.8ns 08h 08h BYTE36 ~61 Superset Information (may be used in future) BYTE62 SPD Revision BYTE63 Checksum for Byte 0~62 BYTE64 Manufacturer JEDEC ID Code BYTE65 ~71 ....Manufacturer JEDEC ID Code BYTE72 Manufacturing Location Rev. 0.3/Jan. 02 NOTE 512MB 80h - 00h Intel SPD 1.2B 12h - DCh 3, 8 1Dh Hynix JEDED ID ADh Unused FFh Hynix (Korea Area) HSA (United States Area) HSE (Europe Area) HSJ (Japan Area) HSS(Singapore) ASIA Area 0*h 1*h 2*h 3*h 4*h 5*h 9 5 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series Continued BYTE NUMBER FUNCTION DESCRIPTION BYTE73 Manufacturer’s Part Number (Component) BYTE74 Manufacturer’s Part Number (256Mb based) BYTE75 Manufacturer’s Part Number (Voltage Interface) BYTE76 BYTE77 FUNCTION VALUE -H -K NOTE -H -K 7 (SDRAM) 37h 4, 5 2 32h 4, 5 V (3.3V, LVTTL) 56h 4, 5 Manufacturer’s Part Number (Memory Width) 6 36h 4, 5 ....Manufacturer’s Part Number (Memory Width) 4 34h 4, 5 BYTE78 Manufacturer’s Part Number (Module Type) C 43h 4, 5 BYTE79 Manufacturer’s Part Number (Data Width) 7 37h 4, 5 BYTE80 ....Manufacturer’s Part Number (Data Width) BYTE81 Manufacturer’s Part Number (Refresh, SDRAM Bank) BYTE82 BYTE83 BYTE84 Manufacturer’s Part Number (Component Configuration) 3 33h 4, 5 6 (8K Refresh, 4Banks) 36h 4, 5 Manufacturer’s Part Number(Manufacturing Site) B 42h 4, 5 Manufacturer’s Part Number (Package Type) T 54h 4, 5 4 (x4 based) 34h 4, 5 BYTE85 Manufacturer’s Part Number (Hyphen) BYTE86 Manufacturer’s Part Number (Min. Cycle Time) - (Hyphen) K 2Dh H 4Bh 4, 5 48h 4, 5 BYTE87~91 Revision Code (for Component) Blanks 20h 4, 6 BYTE92 ....Revision Code (for PCB) Process Code - 4, 6 BYTE93 Manufacturing Date Process Code - 3, 6 BYTE94 ....Manufacturing Date Year - 3, 6 Work Week - 6 Serial Number - BYTE95 ~98 BYTE99 ~125 Assembly Serial Number Manufacturer Specific Data (may be used in future) BYTE126 Intel Sepcification for frequency BYTE127 Intel Specification Details for 100MHz Support BYTE128 ~256 Unused Storage Locations 100MHz 64h Refer to Note7 8Fh 7, 8, 9 8Fh 7, 8, 9 00h - Note : 1. The bank address is excluded 2. 1, 2, 4, 8 for Interleave Burst Type 3. BCD adopted 4. ASCII adopted 5. Basically Hynix writes Part No. except for ‘HYM’ in Byte 73~90 to use the limited 18 bytes from byte 73 to byte 90 6. Not fixed but dependent 7. CK0 connected to DIMM, TBD junction temp, CL2(3) support, Intel defined Concurrent Auto Precharge suport 8. Refer to Intel SPD Specification 1.2B 9. Refer to Hynix web site Byte 82~ 87 for L-Part BYTE NUMBER FUNCTION DESCRIPTION FUNCTION VALUE -H -K -H -K NOTE BYTE82 Manufacturer’s Part Number(Manufacturing Site) B 42h 4, 5 BYTE83 Manufacturer’s Part Number (Power) L 4Ch 4, 5 BYTE84 Manufacturer’s Part Number (Package Type) BYTE85 Manufacturer’s Part Number (Component Configuration) BYTE86 Manufacturer’s Part Number (Hyphent) BYTE87 Manufacturer’s Part Number (Min. Cycle Time) Rev. 0.3/Jan. 02 T 54h 4, 5 4 (x4 based) 34h 4, 5 - (Hyphen) K 2Dh H 4Bh 4, 5 48h 4, 5 6 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Ambient Temperature TA 0 ~ 70 °C Storage Temperature TSTG -55 ~ 125 °C Voltage on Any Pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VDD relative to VSS VDD, VDDQ -1.0 ~ 4.6 V Short Circuit Output Current IOS 50 mA Power Dissipation PD 1 W Soldering Temperature ⋅ Time TSOLDER 260 ⋅ 10 °C ⋅ Sec Note : Operation at above absolute maximum rating can adversely affect device reliability. DC OPERATING CONDITION (TA=0 to 70°C) Parameter Symbol Min Typ Max Unit Note Power Supply Voltage VDD, VDDQ 3.0 3.3 3.6 V 1 Input High voltage VIH 2.0 3.0 VDDQ + 0.3 V 1,2 Input Low voltage VIL -0.3 0 0.8 V 1,3 Note Note : 1.All voltages are referenced to VSS = 0V 2.VIH(max) is acceptable 5.6V AC pulse width with <=3ns of duration. 3.VIL(min) is acceptable -2.0V AC pulse width with <=3ns of duration. AC OPERATING TEST CONDITION (TA=0 to 70°C, VDD=3.3±0.3V, VSS=0V) Parameter Symbol Value Unit AC Input High / Low Level Voltage VIH / VIL 2.4/0.4 V Vtrip 1.4 V Input Rise / Fall Time tR / tF 1 ns Output Timing Measurement Reference Level Voltage Voutref 1.4 V CL 50 pF Input Timing Measurement Reference Level Voltage Output Load Capacitance for Access Time Measurement 1 Note : 1.Output load to measure access times is equivalent to two TTL gates and one capacitor (50pF). For details, refer to AC/DC output load circuit Rev. 0.3/Jan. 02 7 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series CAPACITANCE (TA=25°C, f=1MHz) -K/H Parameter Pin Input Capacitance Data Input / Output Capacitance Symbol Unit Min Max CK0 CI1 - 30 pF CKE0 CI2 - 15 pF /S0, /S2 CI3 - 15 pF A0~12, BA0, BA1 CI4 - 15 pF /RAS, /CAS, /WE CI5 - 15 pF DQM0~DQM7 CI6 - 15 pF DQ0 ~ DQ63 CI/O - 15 pF OUTPUT LOAD CIRCUIT Vtt=1.4V RT=250 Ω Output Output 50pF DC Output Load Circuit Rev. 0.3/Jan. 02 50pF AC Output Load Circuit 8 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series DC CHARACTERISTICS I (TA=0 to 70°C, VDD=3.3±0.3V) Parameter Symbol Min. Max Unit Note Input Leakage Current ILI -10 10 uA 1 Output Leakage Current ILO -1 1 uA 2 Output High Voltage VOH 2.4 - V IOH = -4mA Output Low Voltage VOL - 0.4 V IOL = +4mA Note : 1.VIN = 0 to 3.6V, All other pins are not tested under VIN =0V 2.DOUT is disabled, VOUT=0 to 3.6 DC CHARACTERISTICS II Parameter Operating Current Symbol IDD1 Speed Test Condition -K Burst length=1, One bank active tRC ≥ tRC(min), IOL=0mA -H 2400 CKE ≤ VIL(max), tCK = min 356 CKE ≤ VIL(max), tCK = ∞ 38 IDD2N CKE ≥ VIH(min), CS ≥ VIH(min), tCK = min Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 760 IDD2NS CKE ≥ VIH(min), tCK = ∞ Input signals are stable. 270 IDD3P CKE ≤ VIL(max), tCK = min 446 IDD3PS CKE ≤ VIL(max), tCK = ∞ 216 IDD3N CKE ≥ VIH(min), CS ≥ VIH(min), tCK = min Input signals are changed one time during 2clks. All other pins ≥ VDD-0.2V or ≤ 0.2V 1120 IDD3NS CKE ≥ VIH(min), tCK = ∞ Input signals are stable. 810 Burst Mode Operating Current IDD4 tCK ≥ tCK(min), IOL=0mA All banks active Auto Refresh Current IDD5 tRRC ≥ tRRC(min), All banks active Self Refresh Current IDD6 CKE ≤ 0.2V IDD2P Precharge Standby Current in Power Down Mode IDD2PS Precharge Standby Current in Non Power Down Mode Active Standby Current in Power Down Mode Active Standby Current in Non Power Down Mode Unit Note mA 1 mA mA mA CL=3 mA 3000 mA 1 4900 mA 2 Normal 48 mA 4 Low power 32 mA 5 Note : 1. IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open 2. Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS II 3. All values are measured with Registered and PLL 4. HYM72V64C736BT4-K/H 5. HYM72V64C736BLT4-K/H Rev. 0.3/Jan. 02 9 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series AC CHARACTERISTICS I (AC operating conditions unless otherwise noted) -K Parameter Unit Min System Clock Cycle Time CAS Latency = 3 -H Symbol tCK3 Max 7.5 Min 7.5 1000 CAS Latency = 2 Note Max ns 1000 tCK2 7.5 Clock High Pulse Width tCHW 2.5 - 2.5 - ns 1 Clock Low Pulse Width tCLW 2.5 - 2.5 - ns 1 CAS Latency = 3 tAC3 - 5.4 - 5.4 ns CAS Latency = 2 tAC2 - 6 - 6 ns Data-Out Hold Time tOH 2.7 - 2.7 - ns Data-Input Setup Time tDS 1.5 - 1.5 - ns 1 Data-Input Hold Time tDH 0.8 - 0.8 - ns 1 Address Setup Time tAS 1.5 - 1.5 - ns 1 Address Hold Time tAH 0.8 - 0.8 - ns 1 CKE Setup Time tCKS 1.5 - 1.5 - ns 1 CKE Hold Time tCKH 0.8 - 0.8 - ns 1 Command Setup Time tCS 1.5 - 1.5 - ns 1 Command Hold Time tCH 0.8 - 0.8 - ns 1 CLK to Data Output in Low-Z Time tOLZ 1 - 1 - ns Access Time From Clock CLK to Data Output in High-Z Time 10 ns 2 CAS Latency = 3 tOHZ3 2.7 5.4 2.7 5.4 ns CAS Latency = 2 tOHZ2 2.7 5.4 3 6 ns Note : 1. In Registered DIMM, data is delayed an additional clock cycle due to the register (this is, Device CL + 1 = DIMM CL) 2. Assume tR / tF (input rise and fall time ) is 1ns, If tR & tF > 1ns, then [(tR+tF)/2-1]ns should be added to the parameter 3. Access times to be measured with input signals of 1v/ns edge rate, from 0.8v to 2.0v If tR > 1ns, then (tR/2-0.5)ns should be added to the parameter Rev. 0.3/Jan. 02 10 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series AC CHARACTERISTICS II -K Parameter -H Symbol Unit Min Max Min Max Operation tRC 60 - 65 - ns Auto Refresh tRRC 60 - 65 - ns RAS to CAS Delay tRCD 15 - 20 - ns RAS Active Time tRAS 45 100K 45 100K ns RAS Precharge Time tRP 15 - 20 - ns RAS to RAS Bank Active Delay tRRD 15 - 15 - ns CAS to CAS Delay tCCD 1 - 1 - CLK Write Command to Data-In Delay tWTL 0 - 0 - CLK Data-In to Precharge Command tDPL 2 - 2 - CLK Data-In to Active Command tDAL 5 - 5 - CLK DQM to Data-Out Hi-Z tDQZ 2 - 2 - CLK DQM to Data-In Mask tDQM 0 - 0 - CLK MRS to New Command tMRD 2 - 2 - CLK CAS Latency = 3 tPROZ3 3 - 3 - CLK CAS Latency = 2 tPROZ2 2 - 2 - CLK Power Down Exit Time tPDE 1 - 1 - CLK Self Refresh Exit Time tSRE 1 - 1 - CLK Refresh Time tREF - 64 - 64 ms Note RAS Cycle Time Precharge to Data Output Hi-Z 1 Note : 1. Timing delay due to the register is considered in a registered DIMM 2. A new command can be given tRRC after self refresh exit Rev. 0.3/Jan. 02 11 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series DEVICE OPERATING OPTION TABLE HYM72V64C736B(L)T4-K CAS Latency tRCD tRAS tRC tRP tAC tOH 133MHz(7.5ns) 2CLKs 2CLKs 6CLKs 8CLKs 2CLKs 5.4ns 2.7ns 125MHz(8ns) 2CLKs 3CLKs 6CLKs 9CLKs 3CLKs 6ns 3ns 100MHz(10ns) 2CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns HYM72V64C736B(L)T4-H CAS Latency tRCD tRAS tRC tRP tAC tOH 133MHz(7.5ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 5.4ns 2.7ns 125MHz(8ns) 3CLKs 3CLKs 6CLKs 9CLKs 3CLKs 6ns 3ns 100MHz(10ns) 3CLKs 2CLKs 5CLKs 7CLKs 2CLKs 6ns 3ns Note : DIMM/CAS Latency = Device CL + 1 (Registered Mode) Rev. 0.3/Jan. 02 12 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series COMMAND TRUTH TABLE A10/ AP CKEn-1 CKEn CS RAS CAS WE DQM Mode Register Set H X L L L L X OP code No Operation H X H X X X L H H H X X Bank Active H X L L H H X H X L H L H X CA H X L H L L X CA H X L L H L X X Burst Stop H X L H H L X X DQM H V X Auto Refresh H H L L L H X X Burst-Read-SingleWRITE H X L L L H X A9 Pin High (Other Pins OP code) Entry H L L L L H X Exit L H H X X X L H H H Entry H L H X X X L H H H H X X X L H H H H X X X L V V V Command Read Read with Autoprecharge Write Write with Autoprecharge Precharge All Banks Precharge selected Bank Self Refresh1 X Precharge power down Clock Suspend Exit L H Entry H L Exit L H X X ADDR RA BA Note V L H L H V V H X L V X X X X X X X Note : 1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high 2. X = Don′t care, H = Logic High, L = Logic Low. BA =Bank Address, RA = Row Address, CA = Column Address, Opcode = Operand Code, NOP = No Operation Rev. 0.3/Jan. 02 13 PC133 SDRAM Registered DIMM HYM72V64C736B(L)T4 Series PACKAGE DEMENSION Rev. 0.3/Jan. 02 14