ICS501A LOCO™ PLL CLOCK MULTIPLIER Description Features The ICS501A LOCOTM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands for Low Cost Oscillator, as it is designed to replace crystal oscillators in most electronic systems. Using Phase-Locked Loop (PLL) techniques, the device uses a standard fundamental mode, inexpensive crystal to produce output clocks up to 200 MHz. • • • • • • • • • • • • • • • • • Stored in the chip’s ROM is the ability to generate nine different multiplication factors, allowing one chip to output many common frequencies (see table on page 2). The device also has an output enable pin which tri-states the clock output when the OE pin is taken low. This product is intended for clock generation. It has low output jitter (variation in the output period), but input to output skew and jitter are not defined or guaranteed. For applications which require defined input to output skew, use the ICS570B. Packaged as 8-pin SOIC or die ICS’ lowest cost PLL clock Zero ppm multiplication error Input crystal frequency of upto 27 MHz Input clock frequency of upto 50 MHz Output clock frequencies up to 200 MHz Extremely low jitter of 25 ps (one sigma) Compatible with all popular CPUs Duty cycle of 45/55 up to 200 MHz Nine selectable frequencies Operating voltage of 3.3V Tri-state output for board level testing 25mA drive capability at TTL levels Ideal for oscillator replacement Optimized for output frequencies of upto to 200 MHz Industrial temperature version available Advanced, low power CMOS process Block Diagram VDD S1:0 2 PLL Clock Multiplier Circuitry and ROM X1/ICLK Crystal or Clock input Crystal Oscillator CLK X2 Optional crystal capacitors OE GND 1 MDS 501A B I n t e gra te d C i r c u i t S y s t e m s ● 5 25 Race Stre et, San Jo se, CA 9 5126 Revision 120704 ● te l (40 8) 2 97-12 01 ● w w w. i c st . c o m ICS501A LOCO™ PLL Clock Multiplier Pin Assignment Clock Output Table S1 S0 CLK Minimum Input (MHz) 0 0 4X input 15 X1/ I CLK 1 8 X2 0 M 5.333X input 12 VDD 2 7 OE 0 1 5X input 12 GND 3 6 S0 M 0 10X input 6 M M 2X input 30 M 1 12X input 5 1 0 6X input 10 1 M 3X input 20 1 1 8X input 10 S1 5 4 CLK 8 Pi n ( 150 mi l ) SOI C 0 = connect directly to ground 1 = connect directly to VDD M = leave unconnected (floating) Pin Descriptions Pin Number Pin Name Pin Type 1 XI/ICLK Input Crystal connection or clock input. 2 VDD Power Connect to +3.3 V. 3 GND Power Connect to ground. 4 S1 Tri-level Iinput 5 CLK Output 6 S0 Tri-level Input 7 OE Input 8 X2 Output Select 1 for output clock. Connect to GND or VDD or float. Clock output per table above. Select 0 for output clock. Connect to GND or VDD or float. Output enable. Tri-states CLK output when low. Internal pull-up resistor. Crystal connection. Leave unconnected for clock input. 2 MDS 501A B In te grated Circuit Systems Pin Description ● 525 Ra ce Street, San Jose, CA 9512 6 Revision 120704 ● tel (4 08) 297 -1 201 ● w w w. i c s t . c o m ICS501A LOCO™ PLL Clock Multiplier External Components Crystal Load Capacitors Decoupling Capacitor As with any high-performance mixed-signal IC, the ICS501A must be isolated from system power supply noise to perform optimally. A decoupling capacitor of 0.01µF must be connected between VDD and the GND. It must be connected close to the ICS501A to minimize lead inductance. No external power supply filtering is required for the ICS501A. Series Termination Resistor A 33Ω terminating resistor can be used next to the CLK pin for trace lengths over one inch. The value (in pF) of these crystal caps should equal (CL -12 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 8 pF [(16-12) x 2] = 8. 3 MDS 501A B In te grat ed Circuit Syst ems The total on-chip capacitance is approximately 12 pF. A parallel resonant, fundamental mode crystal should be used. The device crystal connections should include pads for small capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) between the crystal and device. Crystal capacitors, if needed, must be connected from each of the pins X1 and X2 to ground. ● 525 Ra ce St reet , San Jose, CA 9512 6 Revision 120704 ● t el (4 08) 297 -1 201 ● w w w. i c s t . c o m ICS501A LOCO™ PLL Clock Multiplier Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS501A. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5V to VDD+0.5V Ambient Operating Temperature -40 to +85°C Storage Temperature -65 to +150°C Soldering Temperature 260°C Recommended Operation Conditions Parameter Min. Max. Units 0 +70 °C +3.0 +3.6 V Ambient Operating Temperature Power Supply Voltage (measured in respect to GND) Typ. DC Electrical Characteristics VDD=3.3 V ±10% , Ambient temperature 0 to +70°C, unless stated otherwise Parameter Operating Voltage Symbol Conditions Min. VDD Typ. 3.0 Input High Voltage, ICLK only VIH ICLK (pin 1) Input Low Voltage, ICLK only VIL ICLK (pin 1) Input High Voltage VIH OE (pin 7) Input Low Voltage VIL OE (pin 7) Input High Voltage VIH S0, S1 Input Low Voltage VIL S0, S1 Output High Voltage VOH IOH = -12 mA Output Low Voltage VOL IOL = 12 mA Max. Units 3.6 V (VDD/2)+1 V (VDD/2)-1 2.0 V V 0.8 VDD-0.5 V V 0.5 2.4 V V 0.4 V IDD Operating Supply Current, 20 No load, 100M 20 mA Short Circuit Current CLK output +70 mA 4 MDS 501A B In te grat ed Circuit Syst ems ● 525 Ra ce St reet , San Jose, CA 9512 6 Revision 120704 ● t el (4 08) 297 -1 201 ● w w w. i c s t . c o m ICS501A LOCO™ PLL Clock Multiplier Parameter Symbol Conditions On-Chip Pull-up Resistor Pin 7 Input Capacitance, S1, S0, and OE Pins 4, 6, 7 Min. Typ. Nominal Output Impedance Max. Units 270 kΩ 4 pF 20 Ω AC Electrical Characteristics VDD = 3.3 V ±10%, Ambient Temperature 0 to +70° C, unless stated otherwise Parameter Symbol Conditions Min. Typ. Max. Units Input Frequency, crystal input FIN see page 2 27 MHz Input Frequency, clock input FIN see page 2 50 MHz 0°C to +70°C 200 MHz -40°C to +85°C TBD MHz Output Frequency, VDD = 3.0 to 3.6V FOUT Output Clock Rise Time tOR 0.8 to 2.0 V, Note 1 1 ns Output Clock Fall Time tOF 2.0 to 8.0 V, Note 1 1 ns Output Clock Duty Cycle tOD 1.5 V, up to 160 MHz PLL Bandwidth 45 49-51 120 55 % kHz Output Enable Time, OE high to output on 50 ns Output Disable Time, OE low to tri-state 50 ns +70 ps 25 ps Absolute Clock Period Jitter tja One Sigma Clock Period Jitter tjs Deviation from mean Note 1: Measured with 15 pF load. 5 MDS 501A B In te grat ed Circuit Syst ems ● 525 Ra ce St reet , San Jose, CA 9512 6 Revision 120704 ● t el (4 08) 297 -1 201 ● w w w. i c s t . c o m ICS501A LOCO™ PLL Clock Multiplier Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters Inches 8 Symbol E A A1 B C D E e H h L α H INDEX AREA 1 2 D Min Max 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° A Min Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce SEATING PLANE B L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature ICS501AM ICS501AMT ICS501AMI ICS501AMIT ICS501A-DWF ICS501A-DPK 501AM 501AM 501AI 501AI - Tubes Tape and Reel Tubes Tape and Reel Die on uncut, probed wafers Tested die in waffle pack 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 0 to +70° C 0 to +70° C -40 to +85° C -40 to +85° C 0 to +70° C 0 to +70° C While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 6 MDS 501A B In te grat ed Circuit Syst ems ● 525 Ra ce St reet , San Jose, CA 9512 6 Revision 120704 ● t el (4 08) 297 -1 201 ● w w w. i c s t . c o m