IDT IDT71P73604167BQ

IDT71P73204
IDT71P73104
IDT71P73804
IDT71P73604
18Mb Pipelined
DDR™II SRAM
Burst of 4
Features
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
Description
The IDT DDRIITM Burst of four SRAMs are high-speed synchronous memories with a double-data-rate (DDR), bidirectional data port.
This scheme allows maximization on the bandwidth on the data bus by
passing two data items per clock cycle. The address bus operates at
less than single data rate speeds,allowing the user to fan out addresses
and ease system design while maintaining maximum performance on
data transfers.
The DDRII has scalable output impedance on its data output bus
and echo clocks, allowing the user to tune the bus for low noise and high
performance.
All interfaces of the DDRII SRAM are HSTL, allowing speeds
beyond SRAM devices that use any form of TTL interface. The interface can be scaled to higher voltages (up to 1.9V) to interface with 1.8V
systems if necessary. The device has a VDDQ and a separate Vref,
allowing the user to designate the interface operational voltage, independent of the device core voltage of 1.8V VDD. The output impedance
control allows the user to adjust the drive strength to adapt to a wide
range of loads and transmission lines.
18Mb Density (2Mx8, 2Mx9, 1Mx18, 512Kx36)
Common Read and Write Data Port
Dual Echo Clock Output
4-Word Burst on all SRAM accesses
Multiplexed Address Bus
One Read or One Write request per two clock
cycles.
DDR (Double Data Rate) Data Bus
- Four word bursts data per two clock cycles
Depth expansion through Control Logic
HSTL (1.5V) inputs that can be scaled to receive signals
from 1.4V to 1.9V.
Scalable output drivers
Can drive HSTL, 1.8V TTL or any voltage level
from 1.4V to 1.9V.
Output Impedance adjustable from 35 ohms to 70
ohms
1.8V Core Voltage (VDD)
JTAG Interface
165-ball, 1.0mm pitch, 13mm x 15mm fBGA Package
Functional Block Diagram
DATA
REG
(Note1)
K
K
C
C
18M
MEMORY
ARRAY
(Note4)
(Note4)
OUTPUT SELECT
(Note3)
CTRL
LOGIC
(Note2)
OUTPUT REG
ADD
REG
SENSE AMPS
LD
RW
BWx
(Note2)
WRITE/READ DECODE
WRITE DRIVER
SA
SA0
SA 1
CLK
GEN
(Note1)
DQ
CQ
CQ
SELECT OUTPUT CONTROL
6431 drw 16
Notes
1) Represents 8 data signal lines for x8, 9 signal lines for x9, 18 signal lines for x18, and 36 signal lines for x36
2) Represents 19 address signal lines for x8 and x9, 20 address signal lines for x18, and 19 address signal lines for x36.
3) Represents 1 signal line for x9, 2 signal lines for x18, and four signal lines for x36. On x8 parts, the BW is a “nibble write” and there are 2
signal lines.
4) Represents 16 data signal lines for x8, 18 signal lines for x9, 36 signal lines for x18, and 72 signal lines for x36.
JULY 2005
1
©2005 Integrated Device Technology, Inc. “QDR SRAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress Semiconductor, IDT, and Micron Technology, Inc.“
DSC-6431/00
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Clocking
The DDRII SRAM has two sets of input clocks, namely the K, K
clocks and the C, C clocks. In addition, the QDRII has an output “echo”
clock, CQ, CQ.
The K and K clocks are the primary device input clocks. The K
clock is used to clock in the control signals (LD, R/W and BWx or NWx),
the address, and the first and third words of the data burst during a write
operation. The K clock is used to clock in the control signals (BWx or
NWx), and the second and fourth words of the data burst during a write
operation. The K and K clocks are also used internally by the SRAM. In
the event that the user disables the C and C clocks, the K and K clocks
will also be used to clock the data out of the output register and generate
the echo clocks.
The C and C clocks may be used to clock the data out of the
output register during read operations and to generate the echo clocks.
C and C must be presented to the SRAM within the timing tolerances.
The output data from the DDRII will be closely aligned to the C and C
input, through the use of an internal DLL. When C is presented to the
DDRII SRAM, the DLL will have already internally clocked the data to
arrive at the device output simultaneously with the arrival of the C clock.
The C and second data item of the burst will also correspond. The third
and fourth data words will follow on the next clock cycle of the C and C,
respectively.
Single Clock Mode
The DDRII SRAM may be operated with a single clock pair. C
and C may be disabled by tying both signals high, forcing the outputs
and echo clocks to be controlled instead by the K and K clocks.
DLL Operation
The DLL in the output structure of the DDRII SRAM can be used
to closely align the incoming clocks C and C with the output of the data,
generating very tight tolerances between the two. The user may disable
the DLL by holding Doff low. With the DLL off, the C and C (or K and K
if C and C are not used) will directly clock the output register of the
SRAM. With the DLL off, there will be a propagation delay from the time
the clock enters the device until the data appears at the output.
Echo Clock
The echo clocks, CQ and CQ, are generated by the C and C
clocks (or K, K if C, C are disabled). The rising edge of C generates the
rising edge of CQ, and the falling edge of CQ. The rising edge of C
generates the rising edge of CQ and the falling edge of CQ. This
scheme improves the correlation of the rising and falling edges of the
echo clock and will improve the duty cycle of the individual signals.
The echo clock is very closely aligned with the data, guaranteeing that the echo clock will remain closely correlated with the data, within
the tolerances designated.
output at the designated time in correspondence with the C and C clocks.
Write operations are initiated by holding the Read/Write control
input (R/W) low, the load control input (LD) low and presenting the write
address to the address port during the rising edge of K, which will latch
the address. On the following rising edge of K, the first word of the four
word burst must be present on the data input bus DQ[x:O], along with the
appropriate byte write or nibble write (BWx or NWx) inputs. On the
following rising edge of K, the second word of the data write burst will be
accepted at the device input with the designated (BWx or NWx) inputs.
The subsequent K and K rising edges will receive the last two words of
the four word burst, with their BWx/NWx enables.
DDRII devices internally store four words of the burst as a single,
wide word and will retain their order in the burst. The x8 and x9 devices
do not have the ability to address to the single word level or change the
burst order; however the byte and nibble write signals can be used to
prevent writing any byte or individual nibbles, or combined to prevent
writing one word of the burst. The x18 and x36 DDRll devices have the
ability to address to the individual word level using the SA0 and SA1
address bits, but the burst will continue in a linear sequence and wraps
around without incrementing the SA bits. When reading or writing x18
and x36 DDRll devices, the burst will begin at the designated address,
but if the burst is started at any other position than the first word of the
burst, the burst will wrap back on itself and read the first locations before
completing. The x18 and x36 DDRII devices can also use the byte write
signals to prevent writing any individual byte or word of the burst.
Output Enables
The DDRII SRAM automatically enables and disables the DQ[X:0]
outputs. When a valid read is in progress, and data is present at the
output, the output will be enabled. If no valid data is present at the output
(read not active), the output will be disabled (high impedance). The
echo clocks will remain valid at all times and cannot be disabled or turned
off. During power-up the DQ outputs will come up in a high impedance
state.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and Vss to allow the SRAM to adjust its output drive
impedance. The value of RQ must be 5X the value of the intended drive
impedance of the SRAM. The allowable range of RQ to guarantee
impedance matching with a tolerance of +/- 10% is between 175 ohms
and 350 ohms, with VDDQ = 1.5V. The output impedance is adjusted
every 1024 clock cycles to correct for drifts in supply voltage and temperature. If the user wishes to drive the output impedance of the SRAM
to it’s lowest value, the ZQ pin may be tied to VDDQ.
Read and Write Operations
Read operations are initiated by holding Read/Write control input
(R/W) high, the load control input (LD) low and presenting the read
address to the address port during the rising edge of K, which will latch
the address. The data will then be read and will appear at the device
6.42
2
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Definitions
Symbol
Pin Function
Description
Input/Output
Synchronous
Data I/O signals. Data inputs are sampled on the rising edge of K and K during valid write operations. Data outputs are driven
during a valid read operation. The outputs are aligned with the rising edge of both C and C during normal operation. When
operating in a single clock mode (C and C tied high), the outputs are aligned with the rising edge of both K and K. When a
Read operation is not initiated or LD is high (deselected) during the rising edge of K, DQ[X:O] are automatically driven to high
impedance after any previous read operation in progress completes.
2M x 8 -- DQ[7:0]
2M x 9 -- DQ[8:0]
1M x 18 -- DQ[17:0]
512K x 36 -- DQ[35:0]
Input
Synchronous
Byte Write Select 0, 1, 2, and 3 are active LOW. Sampled on the rising edge of the K and again on the rising edge of K clocks
during write operations. Used to select which byte is written into the device during the current portion of the write operations.
Bytes not written remain unaltered. All the byte writes are sampled on the same edge as the data. Deselecting a Byte Write
Select will cause the corresponding byte of data to be ignored and not written in to the device.
2M x 9 -- BW0 controls DQ[8:0]
1M x 18 -- BW0 controls DQ[8:0] and BW1 controls DQ[17:9]
512K x 36 -- BW0 controls DQ[8:0], BW1 controls DQ[17:9], BW2 controls DQ[26:18] and BW3 controls DQ[35:27]
NW0, NW1
Input
Synchronous
Nibble Write Select 0 and 1 are active LOW. Available only on x8 bit parts instead of Byte Write Selects. Sampled on the rising
edge of the K and K clocks during write operations. Used to select which nibble is written into the device during the current
portion of the write operations. Nibbles not written remain unaltered. All the nibble writes are sampled on the same edge as the
data. Deselecting a Nibble Write Select will cause the corresponding nibble of data to be ignored and not written in to the
device.
2M x 8 -- NW0 controls D[3:0] and NW1 controls D[7:4].
SA
Input
Synchronous
Address Inputs. Addresses are sampled on the rising edge of K clock during active read or write operations.
SA0, SA1
Input
Synchronous
Burst count address bits on x18 and x36 DDRll devices. These bits allow changing the burst order in read or write operations, or
addressing to the individual word of a burst. See page 9 for all possible burst sequences.
LD
Input
Synchronous
Load Control Logic. Sampled on the rising edge of K. If LD is low, a four word burst read or write operation will initiate
designated by the R/W input. If LD is high during the rising edge of K, operations in progress will complete, but new operations
will not be initiated.
R/W
Input
Synchronous
Read or Write Control Logic. If LD is low during the rising edge of K, the R/W indicates whether a new operation should be a
read or write. If R/W is high, a read operation will be initiated, if R/W is low, a write operation will be initiated. If the LD input is
high during the rising edge of K, the R/W input will be ignored.
DQ[X:0]
BW0, BW1
BW2, BW3
C
Input Clock
Positive Output Clock Input. C is used in conjunction with C to clock out the Read data from the device. C and C can be used
together to deskew the flight times of various devices on the board back to the controller. See application example for further
details.
C
Input Clock
Negative Output Clock Input. C is used in conjunction with C to clock out the Read data from the device. C and C can be used
together to deskew the flight times of various devices on the board back to the controller. See application example for further
details.
K
Input Clock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device and to drive out data
through DQ[X:0] when in single clock mode. All accesses are initiated on the rising edge of K.
K
Input Clock
Negative Input Clock Input. K is used to capture synchronous inputs being presented to the device and to drive out data through
DQ[X:0] when in single clock mode.
CQ, CQ
Output Clock
Synchronous Echo clock outputs. The rising edges of these outputs are tightly matched to the synchronous data outputs and can
be used as a data valid indication. These signals are free running and do not stop when the output data is three stated.
ZQ
Input
Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus impedance. DQ[X:0]
output impedance is set to 0.2 x RQ, where RQ is a resistor connected between ZQ and ground. Alternately, this pin can be
connected directly to V DDQ, which enables the minimum impedance mode. This pin cannot be connected directly to GND or left
unconnected.
6431 tbl 02a
6.42
3
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Definitions continued
Symbol
Pin Function
Description
Doff
Input
DLL Turn Off. When low this input will turn off the DLL inside the device. The AC timings with the DLL
turned off will be different from those listed in this data sheet. There will be an increased propagation
delay from the incidence of C and C to DQ, or K and K to DQ as configured. The propagation delay is not
a tested parameter, but will be similar to the propagation delay of other SRAM devices in this speed
grade.
TDO
Output
TDO pin for JTAG
TCK
Input
TCK pin for JTAG.
TDI
Input
TDI pin for JTAG. An internal resistor will pull TDI to V DD when the pin is unconnected.
TMS
Input
TMS pin for JTAG. An internal resistor will pull TMS to V DD when the pin is unconnected.
NC
No
Connect
No connects inside the package. Can be tied to any voltage level
VREF
Input
Reference
Reference Voltage input. Static input used to set the reference level for HSTL inputs and Outputs as well
as AC measurement points.
VDD
Power
Supply
Power supply inputs to the core of the device. Should be connected to a 1.8V power supply.
VSS
Ground
Ground for the device. Should be connected to ground of the system.
VDDQ
Power
Supply
Power supply for the outputs of the device. Should be connected to a 1.5V power supply for HSTL or
scaled to the desired output voltage.
6431 tbl 02b
6.42
4
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Configuration IDT71P73204 (2M x 8)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
VSS/
SA (2)
SA
R/W
NW1
K
NC
LD
SA
VSS/
SA (1)
CQ
B
NC
NC
NC
SA
NC
K
NW0
SA
NC
NC
C
NC
NC
NC
VSS
SA
NC
SA
VSS
NC
NC
D
NC
NC
NC
VSS
VSS
VSS
V SS
VSS
NC
NC
E
NC
NC
DQ4
VDDQ
VSS
VSS
V SS
VDDQ
NC
NC
F
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
G
NC
NC
DQ5
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
V DD
VDDQ
VDDQ
VREF
J
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
DQ1
K
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
L
NC
DQ6
NC
VDDQ
VSS
VSS
V SS
VDDQ
NC
NC
M
NC
NC
NC
VSS
VSS
VSS
V SS
VSS
NC
NC
N
NC
NC
NC
VSS
SA
SA
SA
VSS
NC
NC
P
NC
NC
DQ7
SA
SA
C
SA
SA
NC
NC
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
165-ball FBGA Pinout
TOP VIEW
NOTES:
1. A10 is reserved for the 36Mb expansion address.
2. A2 is reserved for the 72Mb expansion address.
6.42
5
DQ3
NC
NC
DQ2
NC
NC
ZQ
NC
NC
DQ0
6431 tbl 12
NC
NC
NC
TDI
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Configuration IDT71P73104 (2M x 9)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
VSS/
SA (2)
SA
R/W
NC
K
NC
LD
SA
VSS/
SA (1)
CQ
B
NC
NC
NC
SA
NC
K
BW
SA
NC
NC
DQ3
C
NC
NC
NC
VSS
SA
NC
SA
VSS
NC
NC
NC
D
NC
NC
NC
VSS
VSS
VSS
V SS
VSS
NC
NC
NC
E
NC
NC
DQ4
VDDQ
VSS
VSS
V SS
VDDQ
NC
NC
DQ2
F
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
NC
G
NC
NC
DQ5
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
NC
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
V DD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
DQ1
NC
K
NC
NC
NC
VDDQ
VDD
VSS
V DD
VDDQ
NC
NC
NC
L
NC
DQ6
NC
VDDQ
VSS
VSS
V SS
VDDQ
NC
NC
DQ0
M
NC
NC
NC
VSS
VSS
VSS
V SS
VSS
NC
NC
NC
N
NC
NC
NC
VSS
SA
SA
SA
VSS
NC
NC
NC
P
NC
NC
DQ7
SA
SA
C
SA
SA
NC
NC
DQ8
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
165-ball FBGA Pinout
TOP VIEW
NOTES:
1. A10 is reserved for the 36Mb expansion address.
2. A2 is reserved for the 72Mb expansion address.
6.42
6
6431 tbl 12a
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Configuration IDT71P73804 (1M x 18)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
V SS/
SA (2)
SA
R/W
BW1
K
NC
LD
SA
Vss/
SA (1)
CQ
B
NC
DQ9
NC
SA
NC
K
BW0
SA
NC
NC
DQ8
C
NC
NC
NC
VSS
SA
SA0
SA1
VSS
NC
DQ7
NC
D
NC
NC
DQ10
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
E
NC
NC
DQ11
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ6
F
NC
DQ12
NC
VDDQ
V DD
V SS
VDD
VDDQ
NC
NC
DQ5
G
NC
NC
DQ13
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
DQ4
NC
K
NC
NC
DQ14
VDDQ
VDD
V SS
VDD
VDDQ
NC
NC
DQ3
L
NC
DQ15
NC
VDDQ
V SS
V SS
VSS
VDDQ
NC
NC
DQ2
M
NC
NC
NC
VSS
VSS
VSS
VSS
VSS
NC
DQ1
NC
N
NC
NC
DQ16
VSS
SA
SA
SA
VSS
NC
NC
NC
P
NC
NC
DQ17
SA
SA
C
SA
SA
NC
NC
DQ0
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
165-ball FBGA Pinout
TOP VIEW
6431 tbl 12b
NOTES:
1. A10 is reserved for the 36Mb expansion address. This must be tied or driven to VSS.on the 1M x 18 DDRII Burst of 4 (71P73804) devices.
2. A2 is reserved for the 72Mb expansion address. This must be tied or driven to VSS on the 1M x 18 DDRII Burst of 4 (71P73804) devices.
6.42
7
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Pin Configuration IDT71P73604 (512K x 36)
1
2
3
4
5
6
7
8
9
10
11
A
CQ
VSS/
SA (3)
NC/
SA (1)
R/W
BW2
K
BW1
LD
SA
VSS/
SA (2)
CQ
B
NC
DQ27
DQ18
SA
BW3
K
BW0
SA
NC
NC
DQ8
C
NC
NC
DQ28
VSS
SA
SA0
SA1
VSS
NC
DQ17
DQ7
D
NC
DQ29
DQ19
VSS
VSS
VSS
VSS
VSS
NC
NC
DQ16
E
NC
NC
DQ20
VDDQ
VSS
VSS
VSS
VDDQ
NC
DQ15
DQ6
F
NC
DQ30
DQ21
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
DQ5
G
NC
DQ31
DQ22
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
DQ14
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
DQ32
VDDQ
VDD
VSS
VDD
VDDQ
NC
DQ13
DQ4
K
NC
NC
DQ23
VDDQ
VDD
VSS
VDD
VDDQ
NC
DQ12
DQ3
L
NC
DQ33
DQ24
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
DQ2
M
NC
NC
DQ34
VSS
VSS
VSS
VSS
VSS
NC
DQ11
DQ1
N
NC
DQ35
DQ25
VSS
SA
SA
SA
VSS
NC
NC
DQ10
P
NC
NC
DQ26
SA
SA
C
SA
SA
NC
DQ9
DQ0
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
165-ball FBGA Pinout
TOP VIEW
NOTES:
1. A3 is reserved for the 36Mb expansion address
2. A10 is reserved for the 72Mb expansion address.
3. A2 is reserved for the 144Mb expansion address.
6.42
8
6431 tbl 12c
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Write Descriptions(1,2)
BW0
BW1
BW2
BW3
NW0
NW1
Write Byte 0
L
X
X
X
X
X
Write Byte 1
X
L
X
X
X
X
Write Byte 2
X
X
L
X
X
X
Write Byte 3
X
X
X
L
X
X
Write Nibble 0
X
X
X
X
L
X
Write Nibble 1
X
X
X
X
X
L
Signal
6431 tbl 09
NOTES:
1) All byte write (BWx) and nibble write (NWx) signals are sampled on
the rising edge of K and again on K. The data that is present on the data
bus in the designated byte/nibble will be latched into the input if the
corresponding BWx or NWx is held low. The rising edge of K will sample
the first and third bytes/nibbles of the four word burst and the rising edge
of K will sample the second and fourth bytes/nibbles of the four word
burst.
2) The availability of the BWx or NWx on designated devices is described in the pin description table.
3) The DDRII Burst of four SRAM has data forwarding. A read request
that is initiated on the cycle following a write request to the same address
will produce the newly written data in response to the read request.
Linear Burst Sequence Table (1,2)
SA [1:0]
a
b
c
d
00
00
01
10
11
01
01
10
11
00
10
10
11
00
01
11
11
00
01
10
NOTES:
1. SA [1:0] is the address presented on pins SA1 and SA0 giving the burst sequence a,b,c,d.
2. SA0 and SA1 are only available on the x18 and x36-bit devices.
6.42
9
6431 tbl 22
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Application Example
SRAM #1
SRAM #4
R=250 Ω
R=250 Ω
ZQ
ZQ
Vt
SA LD R/W
BW0
DQ
BW1 C C K K
DQ
SA
LD R/W BW0 BW1 C C K K
R
Vt
Data Bus
R
Address
R
LD
R/W
BWx/NWx
R
R
R
MEMORY
CONTROLLER
Return CLK
Source CLK
Return CLK
Source CLK
Vt
Vt
Vt
R=50Ω Vt =VREF
6431 drw 20
6.42
10
Vt
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Absolute Maximum Ratings(1)(2)
Capacitance (TA = +25°C, f = 1.0MHz)(1)
Symbol
Rating
Value
Unit
V TERM
Supply Voltage on VDD with
Respect to GND
–0.5 to +2.9
V
V TERM
Supply Voltage on V DDQ with
Respect to GND
–0.5 to VDD+0.3
V TERM
Voltage on Input terminals with
respect to GND
–0.5 to VDD+0.3
V
V TERM
Voltage on Input, Output and I/O
terminals with respect to GND
–0.5 to VDDQ+0.3
V
TBIAS
Temperature Under Bias
–55 to +125
°C
TSTG
Storage Temperature
–65 to +150
°C
IOUT
Continuous Current into Outputs
+ 20
mA
Symbol
CIN
CCLK
V
Recommended DC Operating and
Temperature Conditions
Parameter
Min.
Typ.
Max.
Unit
VDD
Power Supply Voltage
1.7
1.8
1.9
V
VDDQ
I/O Supply Voltage
1.4
1.5
1.9
V
VSS
Ground
0
0
0
V
V REF
Input Reference
Voltage
0.68
V DDQ/2
0.95
V
TA
Ambient Temperature (1)
0
25
70
NOTE:
1. During production testing, the case temperature equals the ambient
temperature.
o
Conditions
Input Capacitance
Clock Input Capacitance
CO
Output Capacitance
CDQ
DQ I/O Capacitance
VDD = 1.8V
VDDQ = 1.5V
Max.
Unit
5
pF
6
pF
7
pF
7
pF
NOTE:
6431 tbl 06
1. Tested at characterization and retested after any design or process change that
may affect these parameters.
6431 tbl 05
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS
may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any other conditions above those
indicated in the operational sections of this specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect
reliability.
2. VDDQ must not exceed VDD during normal operation.
Symbol
Parameter
c
6431 tbl 04
6.42
11
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
DC Electrical Characteristics Over the Operating Temperature and
Supply Voltage Range (VDD = 1.8 ± 100mV, VDDQ = 1.4V to 1.9V)
Parameter
Symbol
Test Conditions
Min
Max
Input Leakage Current
llL
VDD = Max VIN = VSS to VDDQ
-2
+2
Output Leakage Current
lOL
Output Disabled
-2
+2
250MHz
-
800
IDD
VDD = Max,
IOUT = 0mA (outputs open),
Cycle Time > tKHKH Min
200MHz
-
700
167MHz
-
600
250MHz
-
650
200MHz
-
550
167MHz
-
475
250MHz
-
650
200MHz
-
550
167MHz
-
475
250MHz
-
325
200MHz
-
300
167MHz
-
275
Operating Current
(x36): DDR
Operating Current
(x18): DDR
Operating Current
(x9,x8): DDR
Standby Current NOP
IDD
IDD
ISB1
VDD = Max,
IOUT = 0mA (outputs open),
Cycle Time > tKHKH Min
VDD = Max,
IOUT = 0mA (outputs open),
Cycle Time > tKHKH Min
Device Deselected (in NOP state),
IOUT = 0mA (outputs open),
f=Max,
All inputs < 0.2V or > VDD -0.2V
Unit
Note
mA
1
mA
1
mA
1
mA
2
Output High Voltage
VOH1
RQ = 250Ω, IOH = -15mA
VDDQ/2-0.12
VDDQ/2+0.12
V
3, 7
Output Low Voltage
VOL1
RQ = 250Ω, IOL = 15mA
VDDQ/2-0.12
VDDQ/2+0.12
V
4, 7
Output High Voltage
VOH2
IOH = -0.1mA
VDDQ-0.2
VDDQ
V
5
Output Low Voltage
VOL2
IOL = 0.1mA
VSS
0.2
V
6
6431 tbl 10C
NOTES:
1. Operating Current is measured at 100% bus utilization.
2. Standby Current is only after all pending read and write burst operations are completed.
3. Outputs are impedance-controlled. IOH = -(VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175Ω < RQ < 350Ω. This
parameter is tested at RQ = 250Ω, which gives a nominal 50Ω output impedance.
4. Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175Ω < RQ < 350Ω. This
parameter is tested at RQ = 250Ω, which gives a nominal 50Ω output impedance.
5. This measurement is taken to ensure that the output has the capability of pulling to the VDDQ rail, and is not intended to be used as an impedance
measurement point.
6. This measurement is taken to ensure that the output has the capability of pulling to Vss, and is not intended to be used as an impedance
measurement point.
7. Programmable Impedance Mode.
6.42
12
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Input Electrical Characteristics Over the Operating Temperature and
Supply Voltage Range (VDD = 1.8 ± 100mV, VDDQ = 1.4V to 1.9V)
Parameter
Symbol
Min
Max
Unit
Notes
Input High
Voltage, DC
V IH (DC)
VREF +0.1
V DDQ +0.3
V
1,2
Input Low
Voltage, DC
V IL (DC)
-0.3
VREF -0.1
V
1,3
Input High
Voltage, AC
VIH (AC)
VREF +0.2
-
V
4,5
Input Low
Voltage, AC
V IL (AC)
-
VREF -0.2
V
4,5
6431 tbl 10d
NOTES:
1. These are DC test criteria. DC design criteria is VREF + 50mV. The AC VIH/VIL levels are defined separately for measuring timing parameters.
2. VIH (Max) DC = VDDQ+0.3, VIH (Max) AC = VDD +0.5V (pulse width <20% tKHKH (min))
3. VIL (Min) DC = -0.3V, VIL (Min) AC = -0.5V (pulse width <20% tKHKH (min))
4. This conditon is for AC function test only, not for AC parameter test.
5. To maintain a valid level, the transitioning edge of the input must:
a) Sustain a constant slew rate from the current AC level through the target AC level, VIL(AC) or VIH(AC)
b) Reach at least the target AC level.
c) After the AC target level is reached, continue to maintain at least the target DC level, VIL(DC) or VIH(DC)
Overshoot Timing
Undershoot Timing
20% tKHKH (MIN)
VIH
VDD +0.5
VDD +0.25
VSS
VDD
VSS-0.25V
VSS-0.5V
VIL
6431 drw 22
6431 drw 21
20% tKHKH (MIN)
6.42
13
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
AC Test Conditions
Parameter
Symbol
Value
Unit
Core Power Supply Voltage
VDD
1.7-1.9
V
Output Power Supply Voltage
VDDQ
1.4-1.9
V
Input High Level
V IH
(V DDQ/2) + 0.5
V
Input Low Level
VIL
(V DDQ/2) - 0.5
V
VREF
VDDQ/2
V
Input Reference Level
Input Rise/Fall Time
0.3/0.3
TR/TF
ns
DQ Rise/Fall Time
0.5/0.5
Output Timing Reference Level
VDDQ/2
V
6431 tbl 11a
NOTE:
1. Parameters are tested with RQ=250Ω
Input Waveform
(V DDQ /2) + 0.5V
VDDQ /2
Test points
VDDQ /2
(VDDQ /2) - 0.5V
6431 drw 07
Output Waveform
VDDQ/2
Test points
V DDQ /2
6431 drw 08
AC Test Load
VDDQ/2
VREF
RL = 50Ω
VDDQ/2
OUTPUT
Device
Under
Test
ZQ
Z0 =50Ω
RQ = 250 Ω
6431 drw 10
6.42
14
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
AC Electrical Characteristics
(VDD = 1.8 ± 100mV, VDDQ = 1.4V to 1.9V, TA =0 to 70°C )(3,7)
250MHz
Symbol
200MHz
167MHz
Unit
Note
Parameter
Min.
Max
Min.
Max
Min.
Max
4.00
6.30
5.00
7.88
6.00
8.40
ns
-
0.20
-
0.20
-
0.20
ns
1,5
Clock Parameters
tKHKH
Average clock cycle time (K,K,C,C)
tKC var
Cycle to Cycle Period Jitter (K,K,C,C)
tKHKL
Clock High Time (K,K,C,C)
1.60
-
2.00
-
2.40
-
ns
8
tKLKH
Clock LOW Time (K,K,C,C)
1.60
-
2.00
-
2.40
-
ns
8
tKHKH
Clock to clock (K→K, C→C)
1.80
-
2.20
-
2.70
-
ns
9
tKHKH
Clock to clock (K→K, C→C)
1.80
-
2.20
-
2.70
-
ns
9
tKHCH
Clock to data clock (K→C, K→C)
0.00
1.80
0.00
2.30
0.00
2.80
ns
tKC lock
DLL lock time (K,C)
1024
-
1024
-
1024
-
cycles
tKC reset
K static to DLL reset
30
-
30
-
30
-
ns
tCHQV
C,C HIGH to output valid
-
0.45
-
0.45
-
0.50
ns
3
tCHQX
C,C HIGH to output hold
-0.45
-
-0.45
-
-0.50
-
ns
3
2
Output Parameters
tCHCQV
C,C HIGH to echo clock valid
-
0.45
-
0.45
-
0.50
ns
3
TCHCQX
C,C HIGH to echo clock hold
-0.45
-
-0.45
-
-0.50
-
ns
3
TCQHQV
CQ,CQ HIGH to output valid
-
0.30
-
0.35
-
0.40
ns
TCQHQX
CQ,CQ HIGH to output hold
-0.30
-
-0.35
-
-0.40
-
ns
TCHQZ
C HIGH to output HIGH-Z
-
0.45
-
0.45
-
0.50
ns
3,4,5
TCHQX1
C HIGH to output LOW-Z
-0.45
-
-0.45
-
-0.50
-
ns
3,4,5
tAVKH
Address valid to K,K rising edge
0.50
-
0.6
-
0.7
-
ns
6
tIVKH
R, W inputs valid to K,K rising edge
0.50
-
0.6
-
0.7
-
ns
tDVKH
Data-in and BWx/NWx valid to K,K rising edge
0.35
-
0.40
-
0.50
-
ns
tKHAX
K, K rising edge to address hold
0.50
-
0.6
-
0.7
-
ns
tKHIX
K, K rising edge to R, W inputs hold
0.50
-
0.6
-
0.7
-
ns
tKHDX
K, K rising edge to data-in and BWx/NWx hold
0.35
-
0.40
-
0.50
-
ns
Set-Up Time
Hold Times
6
6431 tbl 11
NOTES:
1. Cycle to cycle period jitter is the variance from clock rising edge to the next expected clock rising edge, as defined per JEDEC Standard No.65
(EIA/JESD65) pg.10
2. Vdd slew rate must be less than 0.1V DC per 50 ns for DLL lock retention. DLL lock time begins once Vdd and input clock are stable.
3. If C,C are tied High, K,K become the references for C,C timing parameters.
4. To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ. The specs as shown do not imply bus contention
because tCHQX1 is a MIN parameter that is worse case at totally different test conditions (0°C, 1.9V) than tCHQZ, which is a MAX parameter
(worst case at 70°C, 1.7V). It is not possible for two SRAMs on the same board to be at such different voltage and temperature.
5. This parameter is guaranteed by device characterization, but not production tested.
6. All address inputs must meet the specified setup and hold times for all latching clock edges.
7. During production testing, the case temperature equals TA.
8. Clock High Time (tKHKL) and Clock Low Time (tKLKH) should be within 40% to 60% of the cycle time (tKHKH).
9. Clock to clock time (tKHKH) and Clock to clock time (tKHKH) should be within 45% to 55% of the cycle time (tKHKH).
6.42
15
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Timing Waveform of Combined Read and Write Cycles
NOP
Read A0
(burst of 4)
2
1
Read A1
(burst of 4)
4
3
6
5
Write A2
(burst of 4)
8
NOP
(Note 1)
7
NOP
9
Write A3
(burst of 4)
10
11
Read A4
(burst of 4)
12
13
K
tKHKL
tKLKH
tKHKH
tKHKH
K
Note 2
LD
tKHIX
tIVKH
Note 1
R/W
SA
A3
A2
A1
A0
A4
tAVKH tKHAX
tKHDX
tKHDX
tDVKH
DQ Qx3
Q00
Q02
Q01
Q03
Q0
Q1
Q13
Q12
tDVKH
D20
D21 D22 D23
D30 D31 D32 D33
Q40
tKHCH
tCHQV
tKHCH
tCQHQV
tCQHQX
tCHQV
tCHQX
tCHQX
tCHQZ
tCHQX1
C
tKHKL
tKLKH
tKHKH
tKHKH
C
tCHCQV
tCHCQX
CQ
tCHCQV
tCHCQX
CQ
6431 drw 09
NOTE:
1. If R/W is low on the second rising edge of K after a Read request, the device automatically performs a NOP (No Operation.)
2. The second NOP cycle is not necessary for correct device operation; however, at high clock frequencies, it may be required to prevent bus
contention.
6.42
16
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
IEEE 1149.1 Test Access Port and Boundary Scan-JTAG
This part contains an IEEE standard 1149.1 Compatible Test Access
Port (TAP). The package pads are monitored by the Serial Scan
circuitry when in test mode. This is to support connectivity testing during
manufacturing and system diagnostics. In conformance with IEEE 1149.1,
the SRAM contains a TAP controller, Instruction register, Bypass Register and ID register. The TAP controller has a standard 16-state machine
that resets internally upon power-up; therefore, the TRST signal is not
required. It is possible to use this device without utilizing the TAP. To
disable the TAP controller without interfacing with normal operation of the
SRAM, TCK must be tied to VSS to preclude a mid level input. TMS and
TDI are designed so an undriven input will produce a response identical
to the application of a logic 1, and may be left unconnected, but they may
also be tied to VDD through a resistor. TDO should be left unconnected.
JTAG Block Diagram
JTAG Instruction Coding
IR2
IR1
IR0
Instruction
TDO Output
0
0
0
EXTEST
Boundary Scan Register
0
0
1
IDCODE
Identification register
2
0
1
0
SAMPLE-Z
Boundary Scan Register
1
0
1
1
RESERVED
Do Not Use
5
1
0
0
1
0
1
RESERVED
Do Not Use
5
1
1
0
RESERVED
Do Not Use
5
1
1
1
BYPASS
Bypass Register
3
SRAM
CORE
TDI
BYPASS Reg.
TDO
SAMPLE/PRELOAD Boundary Scan register
Notes
4
Identification Reg.
6431 tbl 13
NOTES:
1. Places DQs in Hi-Z in order to sample all input data regardless of
other SRAM inputs.
2. TDI is sampled as an input to the first ID register to allow for the serial
shift of the external TDI data.
3. Bypass register is initialized to Vss when BYPASS instruction is in
voked. The Bypass Register also holds serially loaded TDI when
existing the Shift DR states.
4. SAMPLE instruction does not place output pins in Hi-Z.
5. This instruction is reserved for future use.
Instruction Reg.
Control Signals
TMS
TCK
TAP Controller
6431 drw 18
TAP Controller State Diagram
1
0
Test Logic Reset
0
Run Test Idle
1
Select DR
1
Select IR
1
1
Capture DR
Shift DR
1
Shift IR
0
Pause DR
1
Exit 2 DR
1
Update DR
0
0
1
1
Exit 1 DR
Exit 1 IR
0
0
1
Capture IR
0
0
1
1
0
0
Pause IR
0
0
0
1
Exit 2 IR
0
1
Update IR
0
1
6431 drw 17
6.42
17
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Scan Register Definition
Part
Instrustion Register
Bypass Register
ID Register
Boundry Scan
512Kx36
3 bits
1 bit
32 bits
107 bits
1Mx18
3 bits
1 bit
32 bits
107 bits
2Mx8/x9
3 bits
1 bit
32 bits
107 bits
6431 tbl 14
Identification Register Definitions
INSTRUCTION FIELD
Revision Number (31:29)
ALL DEVICES
0x0
DESCRIPTION
Revision Number
Device ID (28:12)
0x0290
0x0291
0x0292
0x0293
512Kx36
1Mx18
2Mx9
2Mx8
IDT JEDEC ID CODE (11:1)
0x033
Allows unique identification of SRAM
vendor.
ID Register Presence
Indicator (0)
1
PART NUMBER
DDRII BURST OF 4
71P73604S
71P73804S
71P73104S
71P73204S
Indicates the presence of an ID register.
6431 tbl 15
6.42
18
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Boundary Scan Exit Order (2M x 8-Bit, 2Mx9-Bit, 1Mx18-Bit)
ORDER
PIN ID
ORDER
PIN ID
ORDER
PIN ID
1
6R
37
10D
73
2C
2
6P
38
9E
74
3E
3
6N
39
10C
75
2D
4
7P
40
11D
76
2E
5
7N
41
9C
77
1E
6
7R
42
9D
78
2F
7
8R
43
11B
79
3F
8
8P
44
11C
80
1G
9
9R
45
9B
81
1F
10
11P
46
10B
82
3G
11
10P
47
11A
83
2G
12
10N
48
Internal
84
1J
13
9P
49
9A
85
2J
14
10M
50
8B
15
11N
86
3K
51
7C
16
9M
87
3J
52
6C
17
9N
53
8A
88
2K
18
11L
54
7A
89
1K
19
11M
55
7B
90
2L
20
9L
56
6B
91
3L
21
10L
57
6A
92
1M
22
11K
58
5B
93
1L
23
10K
59
5A
94
3N
24
9J
60
4A
95
3M
25
9K
61
5C
96
1N
26
10J
62
4B
97
2M
27
11J
63
3A
98
3P
28
11H
64
1H
99
2N
29
10G
65
1A
100
2P
30
9G
66
2B
101
1P
31
11F
67
3B
102
3R
32
11G
68
1C
103
4R
33
9F
69
1B
104
4P
34
10F
70
3D
105
5P
35
11E
71
3C
106
5N
36
10E
72
1D
107
5R
6431 tbl 16
6431 tbl 17
6.42
19
6431 tbl 18
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Boundary Scan Exit Order (512K x 36-Bit)
ORDER
PIN ID
ORDER
PIN ID
ORDER
PIN ID
1
6R
37
10D
73
3C
2
6P
38
10E
74
3E
3
6N
39
11C
75
1E
4
7P
40
9D
76
2E
5
7N
41
9C
77
2D
6
7R
42
11D
78
3F
7
8R
43
11B
79
1F
8
8P
44
10B
80
1G
9
9R
45
9B
81
2F
10
11P
46
10C
82
3G
11
9P
47
11A
83
2J
12
10N
48
Internal
84
1J
13
10P
49
9A
85
2G
14
11M
50
8B
86
3K
15
9N
51
7C
87
1K
16
9M
52
6C
17
11N
88
2K
53
8A
18
11L
89
3J
54
7A
19
10L
90
3L
55
7B
20
9L
56
6B
91
1L
21
10M
57
6A
92
1M
22
11K
58
5B
93
2L
23
9K
59
5A
94
3N
24
9J
60
4A
95
2M
25
10K
61
5C
96
1N
26
11J
62
4B
97
3M
27
9G
63
3A
98
3P
28
11H
64
1H
99
1P
29
10G
65
1A
100
2P
30
10J
66
3B
101
2N
31
11F
67
1B
102
3R
32
10F
68
1C
103
4R
33
9F
69
2B
104
4P
34
11G
70
3D
105
5P
35
11E
71
2C
106
5N
36
9E
72
1D
107
5R
6431 tbl 16b
6431 tbl 17b
6.42
20
6431 tbl 18b
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
JTAG DC Operating Conditions
Parameter
Symbol
Min
Typ
Max
Unit
Output Power Supply
V DDQ
1.4
-
1.9
V
Power Supply Voltage
VDD
1.7
1.8
1.9
V
Input High Level
VIH
1.3
-
VDD+0.3
V
Input Low Level
VIL
-0.3
-
0.5
V
TCK Input Leakage Current
IIL
-5
-
+5
µA
TMS, TDI Input Leakage Current
IIL
-15
-
+15
µA
TDO Output Leakage Current
I0L
-5
-
+5
µA
Output High Voltage (IOH =-1mA)
VOH
V DDQ - 0.2
-
VDDQ
V
1
Output Low Voltage (IOL = 1mA)
VOL
V SS
-
0.2
V
1
NOTE:
Note
6431 tbl 19
1. The output impedance of TDO is set to 50 ohms (nominal process) and does not vary with the
external resistor connected to ZQ.
JTAG AC Test Conditions
Parameter
Symbol
Min
Unit
Input High Level
V IH
1.8
V
Input Low Level
VIL
0
V
TR/TF
1.0/1.0
ns
0.9
V
Input Rise/Fall Time
Input and Output Timing Reference Level
Note
1
6431 tbl 20
NOTE:
1. For SRAM outputs see AC test load on page 14.
JTAG Input Test Waveform
JTAG AC Test Load
0.9 V
1.8 V
0.9 V
Test points
0.9 V
0V
50Ω
6431 drw 23
Z0 = 50Ω
TDO
,
6431 drw 25
JTAG Output Test Waveform
0.9 V
Test points
0.9 V
6431 drw 24
6.42
21
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
JTAG AC Characteristics
Parameter
Symbol
Min
Max
Unit
TCK Cycle Time
tCHCH
50
-
ns
TCK High Pulse Width
tCHCL
20
-
ns
TCK Low Pulse Width
tCLCH
20
-
ns
TMS Input Setup Time
tMVCH
5
-
ns
TMS Input Hold Time
tCHMX
5
-
ns
TDI Input Setup Time
tDVCH
5
-
ns
TDI Input Hold Time
tCHDX
5
-
ns
SRAM Input Setup Time
tSVCH
5
-
ns
SRAM Input Hold Time
tCHSX
5
-
ns
Clock Low to Output Valid
tCLQV
0
10
ns
Note
6431 tbl.21
JTAG Timing Diagram
TCK
tM V C H
tC HC L
tCH M X
tD V C H
tC H D X
tS V C H
tC H S X
tC H C H
t C LC H
TMS
T D I/
SRAM
Inp uts
SRAM
O u tpu ts
t C LQ V
TDO
6431 drw 19
6.42
22
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Package Diagram Outline for 165-Ball Fine Pitch Grid Array
6.42
23
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18-Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Ordering Information
IDT
71P73XXX
X
XXX
XX
Device
Type
Power
Speed
Package
BQ
250
200
167
165 Fine Pitch Ball Grid Array (fBGA)
Clock Frequency in MegaHertz
IDT71P73204
IDT71P73104
IDT71P73804
IDT71P73604
2M x 8 DDR II SRAM Burst of 4
2M x 9 DDR II SRAM Burst of 4
1M x 18 DDR II SRAM Burst of 4
512K x 36 DDR II SRAM Burst of 4
6431 drw 15
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or
408-284-8200
fax: 408-284-2775
www.idt.com
for Tech Support:
[email protected]
800-345-7015
“QDR SRAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress Semiconductor, IDT, and Micron Technology, Inc. “
6.42
24
IDT71P73204 (2M x 8-Bit), 71P73104 (2M x 9-Bit), 71P73804 (1M x 18 x -Bit) 71P73604 (512K x 36-Bit)
18 Mb DDR II SRAM Burst of 4
Commercial Temperature Range
Revision History
REV
0
DATE
07/29/05
PAGES
p. 1-24
DESCRIPTION
Released Final datasheet