www.make-ps.com E-mail:[email protected] 2000 series Single, Dual, Triple Output DC/DC Converter FEATURES • • • • • • • • 6 sided Continuous Shielding Synchronization and Output Trim Wide 2:1 Input Voltage Range Efficiency to 86% UL 1950 Approved CSA 22.9-950 Approved VDE / EN 60950 Approved >700,000 Hours MTBF DESCRIPTIONS INPUT CHARACTERISTICS The 2000 series is a family of compact 20 W, high performance DC/DC converters. These converters are specifically designed to provide the flexibility, power density, and reliability required to fulfill local power needs in applications ranging from telecom switch systems to portable instrumentation. 24 models operate over 2:1 input ranges of 9 to 18, 18 to 36 or 36 to 72 VDC; providing single, dual or triple output combinations of 5, 6, 12, 15, ±12, ±15, 5±12 and 5±15 VDC. All models are packaged in compact, low profile 3.0” X 2.56” X 0.75” metal cases. Min Typ Max Unit/Comments Input Voltage Range 12 VDC Input Models VDC 9 12 18 24 VDC Input Models VDC 18 24 36 48 VDC Input Models VDC 36 48 72 Remote ON / OFF Control Supply ON 5.5 VDC or Open Circuit Supply OFF 0 VDC to 0.8 VDC Logic Referenced to Negative Input Input Filter Pi Filter OUTPUT CHARACTERISTICS GENERAL CHARACTERISTICS Min Typ Max Unit/Comments Output Voltage Accuracy Single & Dual Outputs Triple Outputs - Primary - Auxiliaries Output Voltage Adjustment Voltage Balance: Dual Outputs Triple Outputs (Auxiliaries) Minimum Load Line Regulation Single Outputs Dual Outputs Triple Outputs - Primary - Auxiliaries Load Regulation Single Outputs Dual Outputs Triple Outputs - Primary - Auxiliaries Ripple/Noise Single & Dual Output Triple Output Models Primary Auxiliaries Short Circuit Protection Transient Recovery Time Temperature Coefficient Over Voltage Protection ±1.0 ±1.0 ±6.0 ±5.0 % %1 %1 % 1; 1 Switching Frequency Isolation Voltage Isolation Resistance MTBF (MIL-HBK-217F) ±0.5 %; Equal Output Loads ±50 mV; Equal Output Loads 10% Full Load ±0.5 ±0.4 ±0.2 ±1.0 %2 %2 %2 %2 ±0.5 ±0.5 ±0.5 ±5.0 %3 % 3 ; Equal Loads %3 % 3 ; Equal Loads Min Typ Max Unit/Comments kHz 100 VDC, 1 minute 500 Mohm, 500VDC 1000 Thousand Hours, 700 +25oC, Ground Benign ±1.0 % Pk-Pk of Vout 100mV Pk-Pk ±1.0 % Pk-Pk of Vout Continuous, Automatic Recovery 100 uS to within 1% error band for 50% step load change ±0.02 % per oC See Model Selection Guide 1 2 3 = Output voltage at nominal line & FL = % Output voltage measured from min. input line to maximum = Output voltage measured from FL to 10% Load >> 1 www.make-ps.com E-mail:[email protected] ENVIRONMENTAL SPECIFICATIONS Min -30 -40 Operating Temp. Range Storage Temp. Range Relative Humidity PHYSICAL CHARACTERISTICS Typ Max +75 +125 95 Cooling Unit/Comments o C; Ambient o C % Humidity; noncondensing Free-Air Convection Case Size Case Material Shield Connection 12V and 24V Input Models 48V Input Models Flammability Weight Unit/Comments 2.56 X 3.0 X 0.75 inches (65.0 X 76.2 X 19.1 mm) Coated Metal with NonConductive Base Negative Input Positive Input UL94V-0 227 Grams OUTLINE DRAWING CASE G 2.56 (65.0) 0.40 0.40 0.40 0.50 0.30 0.30 (10.2) (10.2) (10.2) (12.7) (7.6) (7.6) 10 9 8 7 6 0.20 (5.1) PIN OUT CHART; CASE G 0.040±.005 (1.01) DIA. 5 BOTTOM 1.00 (25.4) See Note 2 0.72 (18.3) 4 0.70 (17.8) 3.00 (76.2) 3 1.25 (31.75) 2 SIDE 0.02 MIN. (0.5) Single Triple Dual Pin Remote On/Off Remote On/Off Remote On/Off 1 + Vin + Vin + Vin 2 - Vin - Vin - Vin 3 Sync Sync Sync 4 + Vout (Aux) + Vout 5 +Sense/Trim(Down)* Output Trim Common(Aux) Common 6 - Vout (Aux) - Vout 7 - Sense/Trim (Up)* + Vout* + Vout (Primary) Output Trim 8 - Vout* - Vout (Primary) No Pin 9 No Pin Output Trim (Primary) No Pin 10 1 0.40 0.40 0.60 (10.2) (10.2) (15.2) * Connections for single output models without sensing or external trimming: For proper operation, externally connect Pin 5 (+Sense) to Pin 8 (+Vout) and Pin 7 (-Sense) to Pin 9 (-Vout) 0.30 (7.6) 0.75 (19.1) 0.25 (6.4) Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 2. Mounting inserts: 4-40 X .10 (2.5) Deep All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. >> 2 www.make-ps.com E-mail:[email protected] HOW TO ORDER HOW TO ORDER 20 XX D XX Wattage Output Voltage Output Configuration (S=Single, D=Dual) Nominal Input Voltage HOW TO ORDER 20 05 /XX T XX Wattage Max. Output Voltage Nominal Input Voltage Aux. Output Voltage Output Configuration (T = Triple) MODEL SELECTION CHART Model 2005S12 2005S24 2005S48 2006S12 2006S24 2006S48 2012S12 2012S24 2012S48 2015S12 2015S24 2015S48 2012D12 2012D24 2012D48 2015D12 2015D24 2015D48 2005/12T12 2005/12T24 2005/12T48 2005/15T12 2005/15T24 2005/15T48 Nominal Input Voltage (VDC) Input Voltage Range (VDC) Input Current (mA) No Load Input Current (mA) Full Load Output Voltage (VDC) Output Current (mA) Output Over Voltage (VDC) % Efficiency @ Full Load 12 24 48 12 24 48 12 24 48 12 24 48 12 24 48 12 24 48 12 24 48 12 24 48 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 9 - 18 18 - 36 36 - 72 30 30 16 30 30 16 30 30 16 30 30 16 40 30 16 40 30 16 40 30 16 40 30 16 2200 1030 510 2160 1000 485 2140 1025 500 2160 1025 515 2140 1025 500 2140 1025 500 2220 1050 515 2220 1050 515 5 5 5 6 6 6 12 12 12 15 15 15 ±12 ±12 ±12 ±15 ±15 ±15 5/±12 5/±12 5/±12 5/±15 5/±15 5/±15 4000 4000 4000 3300 3300 3300 1650 1650 1650 1325 1325 1325 ±825 ±825 ±825 ±660 ±660 ±660 2000/±415 2000/±415 2000/±415 2000/±300 2000/±300 2000/±300 6.5 6.5 6.5 7.5 7.5 7.5 15.0 15.0 15.0 18.0 18.0 18.0 ±15.0 ±15.0 ±15.0 ±18.0 ±18.0 ±18.0 6.5/±15 6.5/±15 6.5/±15 6.5/±18 6.5/±18 6.5/±18 75 81 81 77 83 86 78 80 83 77 81 81 77 80 83 77 81 83 75 79 81 75 79 81 >> 3