IDT IDT77V1254L25

IDT77V1254L25
Quad Port PHY (Physical Layer)
for 25.6 and 51.2
ATM Networks
Features List
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
Description
Performs the PHY-Transmission Convergence (TC) and
Physical Media Dependent (PMD) Sublayer functions for
four 25.6 Mbps ATM channels
Compliant to ATM Forum (af-phy-040.000) and ITU-T I.432.5
specifications for 25.6 Mbps physical interface
Also operates at 51.2 Mbps data rate
UTOPIA Level 1, UTOPIA Level 2, or DPI-4 Interface
3-Cell Transmit & Receive FIFOs
LED Interface for status signalling
Supports UTP Category 3 and 5 physical media
Interfaces to standard magnetics
Low-Power CMOS
3.3V supply with 5V tolerant inputs
144-pin PQFP Package (28 x 28 mm)
Commercial and Industrial Temperature Ranges
The IDT77V1254L25 is a member of IDT's family of products
supporting Asynchronous Transfer Mode (ATM) data communications
and networking. The IDT77V1254L25 implements the physical layer for
25.6 Mbps ATM, connecting four serial copper links (UTP Category 3
and 5) to one ATM layer device such as a SAR or a switch ASIC. The
IDT77V1254L25 also operates at 51.2 Mbps, and is well suited to backplane driving applications.
The 77V1254L25-to-ATM layer interface is selectable as one of three
options: 16-bit UTOPIA Level 2, 8-bit UTOPIA Level 1 Multi-PHY, or
quadruple 4-bit DPI (Data Path Interface).
The IDT77V1254L25 is fabricated using IDT's state-of-the-art CMOS
technology, providing the highest levels of integration, performance and
reliability, with the low-power consumption characteristics of CMOS.
Block Diagram
TXREF
T X C LK
T X D A T A [15:0]
T X P A R IT Y
TX S O C
TXEN
T X C LA V
T X A D D R [4:0]
M O D E [1:0]
T X /R X A T M
C ellF IF O
S cram bler/
D escram bler
5B /4B
E ncoding/
D ecoding
T X /R X A T M
C ellF IF O
S cram bler/
D escram bler
5B /4B
E ncoding/
D ecoding
P /S and S /P
N R ZI
T X /R X A T M
C ellF IF O
S cram bler/
D escram bler
5B /4B
E ncoding/
D ecoding
P /S and S /P
N R ZI
5B /4B
E ncoding/
D ecoding
P /S and S /P
N R ZI
P /S and S /P
N R ZI
D river
+
TX 0
-
C lock R ecovery
+
RX 0
-
D river
+
Tx 1
-
C lock R ecovery
+
Rx1
-
D river
+
- TX 2
C lock R ecovery
+
-RX 2
D river
+
- TX 3
C lock R ecovery
+
-RX 3
P H Y -A T M
Interface
(U T O P IA or D P I)
R X A D D R [4:0]
R X C LK
R X D A T A [15:0]
R X P A R IT Y
R XSO C
RXEN
R X C LA V
INT
RST
M icroprocessor
Interface
RD
WR
CS
A D [7:0]
A LE
T X /R X A T M
C ellF IF O
O SC
S cram bler/
D escram bler
4
RXREF
R X LE D [3:0]
4
T X LE D [3:0]
35 0 5 drw 0 1
.
IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc.
1 of 47
 2001 Integrated Device Technology, Inc.
September 21, 2001
DSC 6003
IDT77V1254L25
Applications
‹
‹
‹
Operation AT 51.2 Mbps
In addition to operation at the standard rate of 25.6 Mbps, the
77V1254L25 is also specified to operate at 51.2 Mbps. Except for the
doubled bit rate, all other aspects of operation are identical to the 25.6
Mbps mode.
Up to 204.8Mbps backplane transmission
Rack-to-rack short links
ATM Switches
77V1254L25 Overview
The 77V1254L25 is a four port implementation of the physical layer
standard for 25.6Mbps ATM network communications as defined by
ATM Forum document af-phy-040.000 and ITU-T I.432.5. The physical
layer is divided into a Physical Media Dependent sub layer (PMD) and
Transmission Convergence (TC) sub layer. The PMD sub layer includes
the functions for the transmitter, receiver and clock recovery for operation across 100 meters of category 3 and 5 unshielded twisted pair
(UTP) cable. This is referred to as the Line Side Interface. The TC sub
layer defines the line coding, scrambling, data framing and synchronization.
On the other side, the 77V1254L25 interfaces to an ATM layer device
(such as a switch core or SAR). This cell level interface is configurable
as either 8-bit Utopia Level 1 Multi-PHY, 16-bit Utopia Level 2, or as four
4-bit DPI interfaces, as determined by two MODE pins. This is referred
to as the PHY-ATM Interface. The pinout and front page block diagram
are based on the Utopia 2 configuration. Table 2 shows the corresponding pin functions for the other two modes, and Figure 2 and Figure
3 show functional block diagrams.
The 77V1254L25 is based on the 77105, and maintains significant
register compatibility with it. The 77V1254L25, however, has additional
register features, and also duplicates most of its registers to provide
significant independence between the four ports.
Access to these status and control registers is through the utility bus.
This is an 8-bit muxed address and data bus, controlled by a conventional asynchronous read/write handshake.
Additional pins permit insertion and extraction of an 8kHz timing
marker, and provide LED indication of receive and transmit status.
Auto-Synchronization and Good Signal
Indication
The 77V1254L25 features a new receiver synchronization algorithm
that allow it to achieve 4b/5b symbol framing on any valid data stream.
This is an improvement on earlier products which could frame only on
the escape symbol, which occurs only in start-of-cell or 8kHz (X8) timing
marker symbol pairs.
ATM25 transceivers always transmit valid 4b/5b symbols, allowing
the 77V1254L25 receive section to achieve symbol framing and properly
indicate receive signal status, even in the absence of ATM cells or 8kHz
(X8) timing markers in the receive data stream. A state maching monitors the received symbols and asserts the “Good Signal” status bit when
a valid signal is being received. “Good Signal” is deasserted and the
receive FIFO is disabled when the signal is lost. This is sometimes
referred to as Loss of Signal (LOS).
The rate is determined by the frequency of the clock applied to the
OSC input pin. OSC is 32 MHz for the 25.6 Mbps line rate, and 64 MHz
for the 51.2 Mbps line rate. All ports operate at the same frequency.
See Figure 36 for recommended line magnetics. Magnetics for 51.2
Mbps operation have a higher bandwidth than magnetics optimized for
25.6 Mbps.
Functional Description
Transmission Convergence (TC) Sub Layer
Introduction
The TC sub layer defines the line coding, scrambling, data framing
and synchronization. Under control of a switch interface or Segmentation and Reassembly (SAR) unit, the 25.6Mbps ATM PHY accepts a 53byte ATM cell, scrambles the data, appends a command byte to the
beginning of the cell, and encodes the entire 53 bytes before transmission. These data transformations ensure that the signal is evenly distributed across the frequency spectrum. In addition, the serialized bit
stream is NRZI coded. An 8kHz timing sync pulse may be used for
isochronous communications.
Data Structure and Framing
Each 53-byte ATM cell is preceded with a command byte. This byte
is distinguished by an escape symbol followed by one of 17 encoded
symbols. Together, this byte forms one of seventeen possible command
bytes. Three command bytes are defined:
1. X_X (read: 'escape' symbol followed by another 'escape'): Startof-cell with scrambler/descrambler reset.
2. X_4 ('escape' followed by '4'): Start-of-cell without scrambler/
descrambler reset.
3. X_8 ('escape' followed by '8'): 8kHz timing marker. This
command byte is generated when the 8kHz sync pulse is
detected, and has priority over all line activity (data or command
bytes). It is transmitted immediately when the sync pulse is
detected. When this occurs during a cell transmission, the data
transfer is temporarily interrupted on an octet boundary, and the
X_8 command byte is inserted. This condition is the only allowed
interrupt in an otherwise contiguous transfer.
Below is an illustration of the cell structure and command byte
usage:
{X_X} {53-byte ATM cell} {X_4} {53-byte ATM {X_8} cell} ...
In the above example, the first ATM cell is preceded by the X_X
start-of-cell command byte which resets both the transmitter-scrambler
and receiver-descrambler pseudo-random nibble generators (PRNG) to
their initial states. The following cell illustrates the insertion of a start-ofcell command without scrambler/descrambler reset. During this cell's
transmission, an 8kHz timing sync pulse triggers insertion of the X_8
8kHz timing marker command byte.
2 of 47
September 21, 2001
IDT77V1254L25
Transmission Description
Refer to Figure 4. Cell transmission begins with the PHY-ATM Interface. An ATM layer device transfers a cell into the 77V1254L25 across
the Utopia or DPI transmit bus. This cell enters a 3-cell deep transmit
FIFO. Once a complete cell is in the FIFO, transmission begins by
passing the cell, four bits (MSB first) at a time to the 'Scrambler'.
The 'Scrambler' takes each nibble of data and exclusive-ORs them
against the 4 high order bits (X(t), X(t-1), X(t-2), X(t-3)) of a 10 bit
pseudo-random nibble generator (PRNG). Its function is to provide the
appropriate frequency distribution for the signal across the line.
The PRNG is clocked every time a nibble is processed, regardless of
whether the processed nibble is part of a data or command byte. Note
however that only data nibbles are scrambled. The entire command byte
(X _C) is NOT scrambled before it's encoded (see diagram for illustration). The PRNG is based upon the following polynomial:
X10 + X7 + 1
With this polynomial, the four output data bits (D3, D2, D1, D0) will be
generated from the following equations:
D3 = d3 xor X(t-3)
D2 = d2 xor X(t-2)
D1 = d1 xor X(t-1)
D0 = d0 xor X(t)
'DWD
6\PERO
'DWD
6\PERO
'DWD
6\PERO
'DWD
6\PERO
(6&;
GUZ D
This encode/decode implementation has several very desirable properties. Among them is the fact that the output data bits can be represented by a set of relatively simple symbols;
‹ Run length is limited to <= 5;
‹
Disparity never exceeds +/- 1.
On the receiver, the decoder determines from the received symbols
whether a timing marker command (X_8) or a start-of-cell command was
sent (X_X or X_4). If a start-of-cell command is detected, the next 53
bytes received are decoded and forwarded to the descrambler. (See TC
Receive Block Diagram, Figure 5).
The following nibble is scrambled with X(t+4), X(t+3), X(t+2), and
X(t+1).
A scrambler lock between the transmitter and receiver occurs each
time an X_X command is sent. An X_X command is initiated only at the
beginning of a cell transfer after the PRNG has cycled through all of its
states (210 - 1 = 1023 states). The first valid ATM data cell transmitted
after power on will also be accompanied with an X_X command byte.
Each time an X_X command byte is sent, the first nibble after the last
escape (X) nibble is XOR'd with 1111b (PRNG = 3FFx).
Because a timing marker command (X_8) may occur at any time, the
possibility of a reset PRNG start-of-cell command and a timing marker
command occurring consecutively does exist (e.g. X_X_X_8). In this
case, the detection of the last two consecutive escape (X) nibbles will
cause the PRNG to reset to its initial 3FFx state. Therefore, the PRNG is
clocked only after the first nibble of the second consecutive escape pair.
Once the data nibbles have been scrambled using the PRNG, the
nibbles are further encoded using a 4b/5b process. The 4b/5b scheme
ensures that an appropriate number of signal transitions occur on the
line. A total of seventeen 5-bit symbols are used to represent the sixteen
4-bit data nibbles and the one escape (X) nibble. The table below lists
the 4-bit data with their corresponding 5-bit symbols:
3 of 47
September 21, 2001
7;
7;
*1'
$*1'
$9''
5;
5;
$9''
$*1'
$*1'
$9''
5;
5;
$9''
$*1'
$*1'
$9''
$*1'
26&
$9''
$*1'
$*1'
$9''
5;
5;
$9''
$*1'
$*1'
$9''
5;
5;
$9''
$*1'
*1'
7;
7;
IDT77V1254L25
77V1254L25
9
34)3
9''
*1'
7;
7;
9''
'$
6(
$'
$'
$'
$'
*1'
$'
$'
$'
$'
9''
$/(
CS
RD
WR
RST
*1'
INT
9''
*1'
5;/('
5;/('
5;/('
5;/('
9''
*1'
5;'$7$
5;'$7$
5;'$7$
5;'$7$
.
7;$''5
9''
7;$''5
7;$''5
7;$''5
7;&/$9
7;&/.
*1'
9''
5;&/.
RXEN
5;$''5
5;$''5
*1'
5;$''5
5;$''5
5;$''5
5;&/$9
5;62&
*1'
9''
5;3$5,7<
5;'$7$
5;'$7$
5;'$7$
5;'$7$
5;'$7$
5;'$7$
5;'$7$
5;'$7$
*1'
9''
5;'$7$
5;'$7$
5;'$7$
5;'$7$
9''
*1'
7;
7;
9''
00
02'(
02'(
RXREF
TXREF
*1'
7;/('
7;/('
7;/('
7;/('
9''
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;'$7$
7;3$5,7<
TXEN
7;62&
7;$''5
GUZ Figure 1 Pin Assignments
4 of 47
September 21, 2001
IDT77V1254L25
Signal Descriptions
Line Side Signals
Signal Name
Pin Number
I/O
Signal Description
RX0+,-
139, 138
In
Port 0 positive and negative receive differential input pair.
RX1+,-
133, 132
In
Port 1 positive and negative receive differential input pair.
RX2+,-
121, 120
In
Port 2 positive and negative receive differential input pair.
RX3+,-
115, 114
In
Port 3 positive and negative receive differential input pair.
TX0+,-
4, 3
Out
Port 0 positive and negative transmit differential output pair.
TX1+,-
144, 143
Out
Port 1 positive and negative transmit differential output pair.
TX2+,-
110, 109
Out
Port 2 positive and negative transmit differential output pair.
TX3+,-
106, 105
Out
Port 3 positive and negative transmit differential output pair.
Utility Bus Signals
Signal Name
Pin Number
I/O
AD[7:0]
101, 100, 99, 98, 96, 95, 94, In/Out Utility bus address/data bus. The address input is sampled on the falling edge of ALE. Data is output on this
93
bus when a read is performed. Input data is sampled at the completion of a write operation.
ALE
91
CS
90
RD
89
In
Utility bus read enable. Active low asynchronous input. After latching an address, a read is performed by
deasserting WR and asserting RD and CS.
WR
88
In
Utility bus write enable. Active low asynchronous input. After latching an address, a write is performed by
deasserting RD, placing data on the AD bus, and asserting WR and CS. Data is sampled when WR or CS is
deasserted.
In
Signal Description
Utility bus address latch enable. Asynchronous input. An address on the AD bus is sampled on the falling
edge of ALE. ALE must be low when the AD bus is being used for data.
Utility bus asynchronous chip select. CS must be asserted to read or write an internal register. It may remain
asserted at all times if desired
Miscellaneous Signals
Signal Name
Pin Number
I/O
Signal Description
DA
103
In
Reserved signal. This input must be connected to logic low.
INT
85
Out
Interrupt. INT is an open-drain output, driven low to indicate an interrupt. Once low, INT remains low until the
interrupt status in the appropriate interrupt Status Register is read. Interrupt sources are programmable via
the interrupt Mask Registers.
MM
6
In
Reserved signal. This input must be connected to logic low.
MODE[1:0]
7, 8
In
Mode Selects. They determine the configuration of the PHY/ATM interface. 00 = UTOPIA Level 2. 01 = UTOPIA Level 1. 10 = DPI. 11 is reserved.
OSC
126
In
TTL line rate clock source, driven by a 100 ppm oscillator. 32 MHz for 25.6 Mbps; 64 MHz for 51.2 Mbps.
RST
87
In
Reset. Active low asynchronous input resets all control logic, counters and FIFOs. A reset must be performed after power up prior to normal operation of the part.
RXLED[3:0]
82, 81, 80, 79
Out
Receive LED drivers. Driven low for 223 cycles of OSC, beginning with RXSOC when that port receives a
good (non-null and non-errored) cell. Drives 8 mA both high and low. One per port.
RXREF
9
Out
Receive Reference. Active low, synchronous to OSC. RXREF pulses low for a programmable number of
clock cycles when an x_8 command byte is received. Register 0x40 is programmed to indicate which port is
referenced.
SE
102
In
Reserved signal. This input must be connected to logic low.
Table 1 Signal Descriptions (Part 1 of 3)
5 of 47
September 21, 2001
IDT77V1254L25
TXLED[3:0]
12, 13, 14, 15
Out
Ports 3 thru 0 Transmit LED driver. Goes low for 223 cycles of OSC, beginning with TXSOC when this port
receives a cell for transmission. 8 mA drive current both high and low. One per port.
TXREF
10
In
Transmit Reference. Synchronous to OSC. On the falling edge, an X_8 command byte is inserted into the
transmit data stream. Logic for this signal is programmed in register 0x40. Typical application is WAN timing.
Power Supply Signals
Signal Name
Pin Number
I/O
Signal Description
AGND
112, 117, 118, 123, 124,
____
127, 129, 130, 135, 136, 141
Analog ground. AGND supply a ground reference to the analog portion of the ship, which sources a more
constant current than the digital portion.
AVDD
113, 116, 119, 122, 125,
128, 131, 134, 137, 140
Analog power supply 3.3 ± 0.3V AVDD supply power to the analog portion of the chip, which draws a more
constant current than the digital portion.
GND
2, 11, 44, 50, 56, 67, 77, 83, ____
86, 97, 107, 111, 142
Digital Ground.
VDD
1, 5, 16, 38, 45, 57, 68, 78,
84, 92, 104, 108
Digital power supply. 3.3 ± 0.3V.
____
____
16-BIT UTOPIA 2 Signals (MODE[1:0] = 00)
Signal Name
Pin Number
I/O
Signal Description
RXADDR[4:0]
53, 52, 51, 49, 48
In
Utopia 2 Receive Address Bus. This bus is used in polling and selecting the receive port. The port addresses
are defined in bits [4:0] of the Enhanced Control Registers.
RXCLAV
54
Out
Utopia 2 Receive Cell Available. Indicates the cell available status of the addressed port. It is asserted when
a full cell is available for retrieval from the receive FIFO. When non of the four ports is addressed. RXCLAV is
high impedance.
RXCLK
46
In
Utopia 2 Receive Clock. This is a free running clock input.
RXDATA[15:0] 59, 60, 61, 62, 63, 64, 65,
66, 69, 70, 71, 72, 73, 74,
75, 76
Out
Utopia 2 Receive Data. When one of the four ports is selected, the 77V1254L25 transfers received cells to an
ATM device across this bus. Also see RXPARITY.
RXEN
47
In
Utopia 2 Receive Enable. Driven by an ATM device to indicate its ability to receive data across the RXDATA
bus.
RXPARITY
58
Out
Utopia 2 Receive Data Parity. Odd parity over RXDATA[15:0].
RXSOC
55
Out
Utopia 2 Receive Start of Cell. Asserted coincident with the first word of data for each cell on RXDATA.
TXADDR[4:0]
36, 37, 39, 40, 41
In
Utopia 2 Transmit Address Bus. This bus is used in polling and selecting the transmit port. The port
addresses are defined in bits [4:0] of the Enhanced Control Registers.
TXCLAV
42
Out
Utopia 2 Transmit Cell Available. Indicates the availability of room in the transmit FIFO of the addressed port
for a full cell. When none of the four ports is addressed, TXCLAV is high impedance.
TXCLK
43
In
Utopia Transmit Clock. This is a free running clock input.
TXDATA[15:0] 32, 31, 30, 29, 28, 27, 26,
25, 24, 23, 22, 21, 20, 19,
18, 17
In
Utopia 2 Transmit Data. An ATM device transfers cells across this bus to the 77V1254L25 for transmission.
Also see TXPARITY.
TXEN
34
In
Utopia 2 Transmit Enable. Driven by an ATM device to indicate it is transmitting data across the TXDATA
bus.
TXPARITY
33
In
Utopia 2 Transmit Data Parity. Odd parity across TXDATA[15:0]. Parity is checked and errors are indicated in
the Interrupt Status Registers, as enabled in the Master Control Registers. No other action is taken in the
event of an error. Tie high or low if unused.
TXSOC
35
In
Utopia 2 Transmit Start of Cell. Asserted coincident with the first word of data for each cell on TXDATA.
Table 1 Signal Descriptions (Part 2 of 3)
6 of 47
September 21, 2001
IDT77V1254L25
8-BIT UTOPIA Level 1 Signals (MODE[1:0] = 01)
Signal Name
Pin Number
I/O
Signal Description
RXCLAV[3:0]
64, 65, 66, 54
Out
Utopia 1 Receive Cell Available. Indicates the cell available status of the respective port. It is asserted when
a full cell is available for retrieval from the receive FIFO.
RXCLK
46
In
Utopia 1 Receive Clock. This is a free running clock input.
RXDATA[7:0]
69, 70, 71, 72, 73, 74, 75, 76 Out
Utopia 1 Receive Data. When one of the four ports is selected, the 77V1254L25 transfers received cells to an
ATM device across this bus. Bit 5 in the Diagnostic Control Registers determines whether RXDATA tri-states
when RXEN[3:0] are high. Also see RXPARITY.
RXEN[3:0]
51, 49, 48, 47
In
Utopia 1 Receive Enable. Driven by an ATM device to indicate its ability to receive data across the RXDATA
bus. One for each port
RXPARITY
58
Out
Utopia 1 Receive Data Parity. Odd parity over RXDATA[7:0].
RXSOC
55
Out
Utopia 1 Receive Start of Cell. Asserted coincident with the first word of data for each cell on RXDATA. Tristatable as determined by bit 5 in the Diagnostic Control Registers.
TXCLAV[3:0]
39, 40, 41, 42
Out
Utopia 1 Transmit cell Available. Indicates the availability of room in the transmit FIFO of the respective port
for a full cell.
TXCLK
43
In
Utopia 1 Transmit Clock. This is a free running clock input.
TXDATA[7:0]
24, 23, 22, 21, 20, 19, 18, 17 In
Utopia 1 Transmit Data. An ATM device transfers cells across the bus to the 77V1254L25 for transmission.
Also see TXPARITY.
TXEN[3:0]
27, 26, 25, 34
In
Utopia 1 Transmit Enable. Driven by an ATM device to indicate it is transmitting data across the TXDATA
bus. One for each port.
TXPARITY
33
In
Utopia 1 Transmit Data Parity. Odd parity across TXDATA[7:0]. Parity is checked and errors are indicated in
the Interrupt Status Registers, as enabled in the Master Control Registers. No other action is taken in the
event of an error. Tie high or low if unused.
TXSOC
35
In
Utopia 1 Transmit Start of Cell. Asserted coincident with the first word of data for each cell on TXDATA.
DPI Mode Signals (MODE[1:0] = 10)
Signal Name
Pin Number
I/O
Signal Description
DPICLK
43
In
DPI Source Clock for Transmit. This is the free-running clock used as the source to generate Pn_TCLK.
Pn_RCLK
52, 51, 49, 48
In
DPI Port ’n’ Receive Clock. Pn_RCLK is cycled to indicate that the interfacing device is ready to receive a
nibble of data on Pn_RD[3:0] of port ’n’.
Pn_RD[3:0]
59, 60, 61, 62, 63, 64, 65,
66, 69, 70, 71, 72, 73, 74,
75, 76
Out
DPI Port ’n’ Receive Data. Cells received on port ’n’ are passed to the interfacing device across this bus.
Each port has its own dedicated bus.
Pn_RFRM
53, 58, 54, 55
Out
DPI Port ’n’ Receive Frame. Pn_RFRM is asserted for one cycle immediately preceding the transfer of each
cell on Pn_RD[3:0].
Pn_TCLK
37, 39, 40, 41
Out
DPI Port ’n’ Transmit Clock. Pn_TCLK is derived from DPICLK and is cycled when the respective port is
ready to accept another 4 bits of data on Pn_TD[3:0].
Pn_TD[3:0]
32, 31, 30, 29, 28, 27, 26,
25, 24, 23, 22, 21, 20, 19,
18, 17
In
DPI Port ’n’ Transmit Data. Cells are passed across this bus to the PHY for transmission on port ’n’. Each
port has its own dedicated bus.
Pn_TFRM
36, 33, 34, 35
In
DPI Port ’n’ Transmit Frame. Start of cell signal which is asserted for one cycle immediately preceding the
first 4 bits of each cell on Pn_TD[3:0].
Table 1 Signal Descriptions (Part 3 of 3)
7 of 47
September 21, 2001
IDT77V1254L25
Signal Assignment as a Function of PHY/ATM Interface Mode
SIGNAL NAME
PIN NUMBER
16-BIT UTOPIA 2
MODE[1,0] = 00
8-BIT UTOPIA 1
MODE[1,0] = 01
DPI
MODE[1,0] = 10
VDD
1
GND
2
TX0-
3
TX0+
4
VDD
5
MM
6
MODE1
7
MODE0
8
RXREF
9
TXREF
10
GND
11
TXLED3
12
TXLED2
13
TXLED1
14
TXLED0
15
VDD
16
TXDATA0
17
TXDATA0
TXDATA0
P0_TD[0]
TXDATA1
18
TXDATA1
TXDATA1
P0_TD[1]
TXDATA2
19
TXDATA2
TXDATA2
P0_TD[2]
TXDATA3
20
TXDATA3
TXDATA3
P0_TD[3]
TXDATA4
21
TXDATA4
TXDATA4
P1_TD[0]
TXDATA5
22
TXDATA5
TXDATA5
P1_TD[1]
TXDATA6
23
TXDATA6
TXDATA6
P1_TD[2]
TXDATA7
24
TXDATA7
TXDATA7
P1_TD[3]
TXDATA8
25
TXDATA8
TXEN[1]
P2_TD[0]
TXDATA9
26
TXDATA9
TXEN[2]
P2_TD[1]
TXDATA10
27
TXDATA10
TXEN[3]
P2_TD[2]
TXDATA11
28
TXDATA11
see note 2
P2_TD[3]
TXDATA12
29
TXDATA12
see note 2
P3_TD[0]
TXDATA13
30
TXDATA13
see note 2
P3_TD[1]
TXDATA14
31
TXDATA14
see note 2
P3_TD[2]
TXDATA15
32
TXDATA15
see note 2
P3_TD[3]
TXPARITY
33
TXPARITY
TXPARITY
P2_TFRM
TXEN
34
TXEN
TXEN[0]
P1_TFRM
TXSOC
35
TXSOC
TXSOC
P0_TFRM
TXADDR4
36
TXADDR4
see note 2
P3_TFRM
Table 2 Signal Assignment as a Function of PHY/ATM Interface Mode (Part 1 of 4)
8 of 47
September 21, 2001
IDT77V1254L25
SIGNAL NAME
PIN NUMBER
TXADDR3
37
VDD
38
TXADDR2
16-BIT UTOPIA 2
MODE[1,0] = 00
8-BIT UTOPIA 1
MODE[1,0] = 01
DPI
MODE[1,0] = 10
TXADDR3
see note 2
P3_TCLK
39
TXADDR2
TXCLAV[3]
P2_TCLK
TXADDR1
40
TXADDR1
TXCLAV[2]
P1_TCLK
TXADDR0
41
TXADDR0
TXCLAV[1]
P0_TCLK
TXCLAV
42
TXCLAV
TXCLAV[0]
see note 1
TXCLK
43
TXCLK
TXCLK
DPICLK
GND
44
VDD
45
RXCLK
46
RXCLK
RXCLK
see note 2
RXEN
47
RXEN
RXEN[0]
see note 2
RXADDR0
48
RXADDR0
RXEN[1]
P0_RCLK
RXADDR1
49
RXADDR1
RXEN[2]
P1_RCLK
GND
50
RXADDR2
51
RXADDR2
RXEN[3]
P2_RCLK
RXADDR3
52
RXADDR3
see note 2
P3_RCLK
RXADDR4
53
RXADDR4
see note 2
P3_RFRM
RXCLAV
54
RXCLAV
RXCLAV[0]
P1_RFRM
RXSOC
55
RXSOC
RXSOC
P0_FRM
GND
56
VDD
57
RXPARITY
58
RXPARITY
RXPARITY
P2_RFRM
RXDATA15
59
RXDATA15
see note 1
P3_RD[3]
RXDATA14
60
RXDATA14
see note 1
P3_RD[2]
RXDATA13
61
RXDATA13
see note 1
P3_RD[1]
RXDATA12
62
RXDATA12
see note 1
P3_RD[0]
RXDATA11
63
RXDATA11
see note 1
P2_RD[3]
RXDATA10
64
RXDATA10
RXCLAV[3]
P2_RD[2]
RXDATA9
65
RXDATA9
RXCLAV[2]
P2_RD[1]
RXDATA8
66
RXDATA8
RXCLAV[1]
P2_RD[0]
GND
67
VDD
68
RXDATA7
69
RXDATA7
RXDATA7
P1_RD[3]
RXDATA6
70
RXDATA6
RXDATA6
P1_RD[2]
RXDATA5
71
RXDATA5
RXDATA5
P1_RD[1]
RXDATA4
72
RXDATA4
RXDATA4
P1_RD[0]
RXDATA3
73
RXDATA3
RXDATA3
P0_RD[3]
Table 2 Signal Assignment as a Function of PHY/ATM Interface Mode (Part 2 of 4)
9 of 47
September 21, 2001
IDT77V1254L25
SIGNAL NAME
PIN NUMBER
16-BIT UTOPIA 2
MODE[1,0] = 00
8-BIT UTOPIA 1
MODE[1,0] = 01
DPI
MODE[1,0] = 10
RXDATA2
74
RXDATA2
RXDATA2
P0_RD[2]
RXDATA1
75
RXDATA1
RXDATA1
P0_RD[1]
RXDATA0
76
RXDATA0
RXDATA0
P0_RD[0]
GND
77
VDD
78
RXLED0
79
RXLED1
80
RXLED2
81
RXLED3
82
GND
83
VDD
84
INT
85
GND
86
RST
87
WR
88
RD
89
CS
90
ALE
91
VDD
92
AD0
93
AD1
94
AD2
95
AD3
96
GND
97
AD4
98
AD5
99
AD6
100
AD7
101
SE
102
DA
103
VDD
104
TX3-
105
TX3+
106
GND
107
VDD
108
TX2-
109
TX2+
110
Table 2 Signal Assignment as a Function of PHY/ATM Interface Mode (Part 3 of 4)
10 of 47
September 21, 2001
IDT77V1254L25
SIGNAL NAME
PIN NUMBER
GND
111
AGND
112
AVDD
113
RX3-
114
RX3+
115
AVDD
116
AGND
117
AGND
118
AVDD
119
RX2-
120
RX2+
121
AVDD
122
AGND
123
AGND
124
AVDD
125
OSC
126
AGND
127
AVDD
128
AGND
129
AGND
130
AVDD
131
RX1-
132
RX1+
133
AVDD
134
AGND
135
AGND
136
AVDD
137
RX0-
138
RX0+
139
AVDD
140
AGND
141
GND
142
TX1-
143
TX1+
144
16-BIT UTOPIA 2
MODE[1,0] = 00
8-BIT UTOPIA 1
MODE[1,0] = 01
DPI
MODE[1,0] = 10
Table 2 Signal Assignment as a Function of PHY/ATM Interface Mode (Part 4 of 4)
Note: 1.This output signal is unused in this mode. It must be left unconnected.
2.This input signal is unused in this mode. It must be connected to either logic high or logic low.
11 of 47
September 21, 2001
IDT77V1254L25
TXRef
7;&/.
7;'$7$>@
7;3DULW\
7;62&
TXEN>@
7;&/$9>@
0RGH>@
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7; 3RUW &ORFN 5HFRYHU\
8723,$
0XOWL3+<
,QWHUIDFH
5;&/.
5;'$7$>@
5;3DULW\
5;62&
7; 3RUW &ORFN 5HFRYHU\
RXEN>@
5;&/$9>@
INT
RST
RD
WR
CS
$'>@
$/(
5; 3RUW 5; 3RUW 7; 3RUW &ORFN 5HFRYHU\
5; 3RUW 0LFURSURFHVVRU
,QWHUIDFH
26&
RXRef
7; 3RUW &ORFN 5HFRYHU\
5; 3RUW 5;/('>@ 7;/('>@
.
GUZ Figure 2 Block Diagram for Utopia Level 1 Configuration (MODE[1:0] = 01)
12 of 47
September 21, 2001
IDT77V1254L25
'3,&/.
TXRef
0RGH>@
3B7&/.
3B7)50
3B7'>@
3B5&/.
3B5)50
3B5'>@
3B7&/.
3B7)50
3B7'>@
3B5&/.
3B5)50
3B5'>@
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7;5; $70
&HOO ),)2
6FUDPEOHU
'HVFUDPEOHU
%%
(QFRGLQJ
'HFRGLQJ
36 DQG 63
15=,
7; 3RUW &ORFN 5HFRYHU\
5; 3RUW 7; 3RUW &ORFN 5HFRYHU\
5; 3RUW '3,
0XOWL3+<
,QWHUIDFH
3B7&/.
3B7)50
3B7'>@
3B5&/.
3B5)50
3B5'>@
3B7&/.
3B7)50
3B7'>@
3B5&/.
3B5)50
3B5'>@
INT
RST
RD
WR
CS
$'>@
$/(
7;5; $70
&HOO ),)2
7; 3RUW &ORFN 5HFRYHU\
5; 3RUW 7; 3RUW &ORFN 5HFRYHU\
5; 3RUW .
0LFURSURFHVVRU
,QWHUIDFH
26&
RXRef
5;/('>@ 7;/('>@
GUZ Figure 3 Block Diagram for DPI configuration (MODE[1:0] = 10)
13 of 47
September 21, 2001
IDT77V1254L25
The output of the 4b/5b encoder provides serial data to the NRZI
encoder. The NRZI code transitions the wire voltage each time a '1' bit is
sent. This, together with the previous encoding schemes guarantees
that long run lengths of either '0' or '1's are prevented. Each symbol is
shifted out with its most significant bit sent first.
When no cells are available to transmit, the 77V1254L25 keeps the
line active by continuing to transmit valid symbols. But it does not
transmit another start-of-cell command until it has another cell for transmission. The 77V1254L25 never generates idle cells.
Transmit HEC Byte Calculation/Insertion
Byte #5 of each ATM cell, the HEC (Header Error Control) is calculated automatically across the first 4 bytes of the cell header, depending
upon the setting of bit 5 of registers 0x03, 0x13, 0x23 and 0x33. This
byte is then either inserted as a replacement of the fifth byte transferred
to the PHY by the external system, or the cell is transmitted as received.
A third operating mode provides for insertion of
"Bad" HEC codes which may aid in communication diagnostics. These
modes are controlled by the LED Driver and HEC Status/Control Registers.
Receiver Description
The receiver side of the TC sublayer operates like the transmitter, but
in reverse. The data is NRZI decoded before each symbol is reassembled. The symbols are then sent to the 5b/4b decoder, followed by the
Command Byte Interpreter, De-Scrambler, and finally through a FIFO to
the UTOPIA or DPI interface to an ATM Layer device.
ATM Cell Format
%LW %LW +HDGHU %\WH +HDGHU %\WH +HDGHU %\WH 8')
3D\ORDG %\WH 3D\ORDG %\WH 8VHU 'HILQHG )LHOG RU +(&
To declare 'Bad Signal' (from "Good" to "Bad") The same updown counter counts from 0 to 7 (being at 0 to provide a "Good" status).
When the clock ticks for 1,024 cycles (32MHz clock, 1,024 cycles =
204.8 symbols) and there is at least one "bad symbol", the counter
increases by one. If it detects all "good symbols" and no "bad symbols"
in the next time period, the counter decreases by one. The "Bad Signal"
is declared when the counter reaches 7. The Good Signal Bit could be
set to 0 as quickly as 1,433 symbols (204.8 x 7) if at least one "bad
symbol" is detected in each of seven consecutive groups of 204.8
symbols.
8kHz Timing Marker
The 8kHz timing marker, described earlier, is a completely optional
feature which is essential for some applications requiring synchronization for voice or video, and unnecessary for other applications. Figure 7
shows the options available for generating and receiving the 8kHz
timing marker.
A received X_8 command byte causes the 77V1254L25 to issue a
negative pulse on RXREF. The source channel of the marker is
programmable.
•
•
•
8')
To declare 'Good Signal' (from "Bad" to "Good") There is an updown counter that counts from 7 to 0 and is initially set to 7. When the
clock ticks for 1,024 cycles (32MHz clock, 1,024 cycles = 204.8
symbols) and no "bad symbol" has been received, the counter
decreases by one. However, if at least one "bad symbol" is detected
during these 1,024 clocks, the counter is increased by one, to a
maximum of 7. The Good Signal Bit is set to 1 when this counter
reaches 0. The Good Signal Bit could be set to 1 as quickly as 1,433
symbols (204.8 x 7) if no bad symbols have been received.
The source of the marker is programmable in the RXREF and
TXREF Control Register (0x40). Each port is individually programmable
to either a local source or a looped remote source. The local source is
TXREF, which is an 8kHz clock of virtually any duty cycle. When
unused, TXREF should be tied high. Also note that it is not limited to
8kHz, should a different frequency be desired. When looped, a received
X_8 command byte causes one to be generated on the transmit side.
+HDGHU %\WH GUZ set to 0 = Bad signal initially) which shows the status of the line per the
following algorithm:
.
PHY-ATM Interface
Note that although the IDT77V1254L25 can detect symbol and HEC
errors, it does not attempt to correct them.
Upon reset or the re-connect, each port's receiver is typically not
symbol-synchronized. When not symbol-synchronized, the receiver will
indicate a significant number of bad symbols, and will deassert the Good
Signal Bit as described below. Synchronization is established immediately once that port receives an Escape symbol, usually as part of the
start-of-cell command byte preceding the first received cell.
The IDT77V1254L25 monitors line conditions and can provide an
interrupt if the line is deemed 'bad'. The Interrupt Status Registers
(registers 0x01, 0x11, 0x21 and 0x31) contain a Good Signal Bit (bit 6,
The 77V1254L25 PHY offers three choices in interfacing to ATM
layer devices such as segmentation and reassembly (SAR) and
switching chips. MODE[1:0] are used to select the configuration of this
interface, as shown in the table below.
UTOPIA is a Physical Layer to ATM Layer interface standardized by
the ATM Forum. It has separate transmit and receive channels and
specific handshaking protocols. UTOPIA Level 2 has dedicated address
signals for both the transmit and receive directions that allow the ATM
layer device to specify with which of the four PHY channels it is communicating. UTOPIA Level 1 does not have address signals.
14 of 47
September 21, 2001
IDT77V1254L25
6WDUW RI &HOO
TXRef N+]
&HOOV
8723,$
RU
Interface
'3, ,QWHUIDFH
6FUDPEOHU
3+<$70
,QWHUIDFH
&RQWURO
+(& *HQ ,QVHUWLRQ
&RPPDQG
%\WH
,QVHUWLRQ
Reset
6FUDPEOH
1LEEOH
1H[W
Pseudo
Random
351*
Nibble Generator
EE
(QFRGLQJ
26&
&ORFN ,QSXW
7; +
7; 15=,
(QFRGLQJ
GUZ Figure 4 TC Transmit Block Diagram
351*
6FUDPEOH
1LEEOH
5HVHW
RXRef
5; 15=,
'HFRGLQJ
EE
'HFRGLQJ
5;
&RPPDQG
%\WH
'HWHFWLRQ
5HPRYDO
'HFRGH
1H[W
'H
6FUDPEOHU
.
6WDUW RI &HOO
&HOOV
0+]
Clock
&ORFN
Recovery
6\QWKHVL]HU
3//
3+<$70
,QWHUIDFH
&RQWURO 5(&9
26&
8723,$
RU
Interface
'3, ,QWHUIDFH
GUZ Figure 5 TC Receive Block Diagram
15 of 47
September 21, 2001
IDT77V1254L25
Instead, key handshaking signals are duplicated so that each
channel has its own signals. In both versions of UTOPIA, all channels
share a single transmit data bus and a single receive data bus for data
transfer.
DPI is a low-pin count Physical Layer to ATM Layer interface. The
low-pin count characteristic allows the 77V1254L25 to incorporate four
separate DPI 4-bit ports, one for each of the four serial ports. As with the
UTOPIA interfaces, the transmit and receive directions have their own
data paths and handshaking.
UTOPIA Level 2 Interface option
The 16-bit Utopia Level 2 interface operates as defined in ATM
Forum document af-phy-0039. This PHY-ATM interface is selected by
setting the MODE[1:0] pins both low.
This mode is configured as a single 16-bit data bus in the transmit
(ATM-to-PHY) direction, and a single 16-bit data bus in the receive
(PHY-to-ATM) direction. In addition to the data bus, each direction also
includes a single optional parity bit, an address bus, and several handshaking signals. The UTOPIA address of each channel is determined by
bits 4 to 0 in the Enhanced Control Registers. Please note that the
transmit bus and the receive bus operate completely independently. The
Utopia 2 signals are summarized below:
then driving TXEN or RXEN low. When TXEN is driven low, TXSOC
(start of cell) is driven high to indicate that the first 16 bits of the cell are
being driven on TXDATA. The ATM device may chose to temporarily
suspend transfer of the cell by deasserting TXEN. Otherwise, TXEN
remains asserted as the next 16 bits are driven onto TXDATA with each
cycle of TXCLK.
In the receive direction, the ATM device selects a port if it wished to
receive the cell that the port is holding. It does this by asserting RXEN.
The PHY then transfers the data 16 bits each clock cycle, as determined by RXEN. As in the transmit direction, the ATM device may
suspend transfer by deasserting RXEN at any time. Note that the PHY
asserts RXSOC coincident with the first 16 bits of each cell.
TXPARITY and RXPARITY are parity bits for the corresponding 16bit data fields. Odd parity is used.
Figure 9 through Figure 14 may be referenced for Utopia 2 bus
examples.
Because this interface transfers an even number of bytes, rather
than the ATM standard of 53 bytes, a filler byte is inserted between the
5-byte header and the 48-byte payload. This is shown in Figure 8.
UTOPIA Level 1 multi-phy interface Option
The UTOPIA Level 1 MULTI-PHY interface is based on ATM Forum
document af-phy-0017. Utopia Level 1 is essentially the same as Utopia
Level 2, but without the addressing, polling and selection features.
TXDATA[15:0]
ATM to PHY
TXPARITY
ATM to PHY
TXSOC
ATM to PHY
TXADDR[4:0]
ATM to PHY
+HDGHU E\WH +HDGHU E\WH TXEN
ATM to PHY
+HDGHU E\WH +HDGHU E\WH TXCLAV
PHY to ATM
+HDGHU E\WH VWXII E\WH
TXCLK
ATM to PHY
3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH RXDATA[15:0]
PHY to ATM
RXPARITY
PHY to ATM
RXSOC
PHY to ATM
RXADDR[4:0]
ATM to PHY
RXEN
ATM to PHY
RXCLAV
PHY to ATM
RXCLK
ATM to PHY
%LW )LUVW
/DVW
%LW Figure 6 Utopia Level 2 Data Format and Sequence
To determine if any of them has room to accept a cell for transmission (TXCLAV), or has a receive cell available to pass on to the ATM
device (RXCLAV). To poll, the ATM device drives an address (TXADDR
or RXADDR) then observes TXCLAV or RXCLAV on the next cycle of
TXCLK or RXCLK. A port must tri-state TXCLAV and RXCLAV except
when it is addressed.
If TXCLAV or RXCLAV is asserted, the ATM device may select that
port, then transfer a cell to or from it. Selection of a port is performed by
driving the address of the desired port while TXEN or RXEN is high,
Instead of addressing, this mode utilizes separate TXCLAV, TXEN,
RXCLAV and RXEN signals for each channel of the 77V1254L25. There
are just one each of the TXSOC and RXSOC signals, which are shared
across all four channels.
In addition to Utopia Level 2's cell mode transfer protocol, Utopia
Level 1 also offers the option of a byte mode protocol. Bit 1 of the
Master Control Registers is used to program whether the UTOPIA Level
1 bus is in cell mode or byte mode. In byte mode, the PHY is allowed to
control data transfer on a byte-by-byte basis via the TXCLAV and
RXCLAV signals. In cell mode, TXCLAV and RXCLAV are ignored once
16 of 47
September 21, 2001
IDT77V1254L25
the transfer of a cell has begun. In every other way the two modes are
identical. Cell mode is the default configuration and is the one described
later.
The Utopia 1 signals are summarized below:
TXDATA[7:0]
ATM to PHY
TXPARITY
ATM to PHY
TXSOC
ATM to PHY
TXEN[3:0]
ATM to PHY
TXCLAV[3:0]
PHY to ATM
TXCLK
ATM to PHY
RXDATA[7:0]
PHY to ATM
RXPARITY
PHY to ATM
RXSOC
PHY to ATM
RXEN[3:0]
ATM to PHY
RXCLAV[3:0]
PHY to ATM
RXCLK
ATM to PHY
Transmit and receive both utilize free running clocks, which are
inputs to the 77V1254L25. All Utopia signals are timed to these clocks.
In the transmit direction, the PHY first asserts TXCLAV (transmit cell
available) to indicate that it has room in its transmit FIFO to accept at
least one 53-byte ATM cell. When the ATM layer device is ready to begin
passing the cell, it asserts TXEN (transmit enable) and TXSOC (start of
cell), coincident with the first byte of the cell on TXDATA. TXEN remains
asserted for the duration of the cell transfer, but the ATM device may
deassert TXEN at any time once the cell transfer has begun, but data is
transferred only when TXEN is asserted.
In the receive direction, RXEN indicates when the ATM device is
prepared to receive data. As with transmit, it may be asserted or deasserted at any time. Note, however, that not more than one RXEN should
be asserted at a time. Also, once a given RX port is selected, that port's
FIFO must be emptied of cells (as indicated by RXCLAV) before a
different RX port may be enabled.
In both transmit and receive, TXSOC and RXSOC (start of cell) is
asserted for one clock, coincident with the first byte of each cell. Odd
parity is utilized across each 8-bit data field.
Figure 8 shows the data sequence for an ATM cell over Utopia Level
1, and Figures 15 to 21 are examples of the Utopia Level 1 handshake.
17 of 47
September 21, 2001
IDT77V1254L25
TXRef ,QSXW
/76HO 5HJ %LW 5;5HI
;B UHFHLYHG
0X[
7;5HI
;B JHQHUDWRU
/76HO 5HJ %LW 5;5HI
;B UHFHLYHG
0X[
7;5HI
;B JHQHUDWRU
/76HO 5HJ %LW 5;5HI
;B UHFHLYHG
0X[
7;5HI
;B JHQHUDWRU
/76HO 5HJ %LW 5;5HI
;B UHFHLYHG
5;5HI6HO>@
0X[
5;5HI
6HOHFW
'HFRGHU
7;5HI
;B JHQHUDWRU
.
,'79/
,'79
RXRef 2XWSXW
GUZ Figure 7 RXREF and TXREF Block Diagram
%LW )LUVW
%LW +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH /DVW
3D\ORDG E\WH GUZ Figure 8 Utopia 1 Data Format and Sequence
18 of 47
September 21, 2001
IDT77V1254L25
SROOLQJ
VHOHFWLRQ
SROOLQJ
SROOLQJ
7;&/.
7;$''5>@
7;&/$9
)
1
1
+LJK=
)
1
)
1
1
1
)
1
)
1
1
TXEN
7;'DWD>@
7;3$5,7<
3 3 3 3 3 + + + XQGHILQHG
3 .
7;62&
3+< 1
3+< 1
FHOO WUDQVPLVVLRQ WR
GUZ Figure 9 Utopia 2 Transmit Handshake - Back to Back Cells
VHOHFWLRQ
SROOLQJ
SROOLQJ
SROOLQJ
7;&/.
7;$''5>@
7;&/$9
)
1
1
+LJK=
)
1
)
1
1
1
)
1
)
1
1
TXEN
7;'DWD>@
7;3$5,7<
3 3 3 + + + XQGHILQHG
3 .
7;62&
3+< 1
3+< 1
FHOO WUDQVPLVVLRQ WR
GUZ Figure 10 Utopia 2 Transmit Handshake - Delay Between Cells
VHOHFWLRQ
SROOLQJ
SROOLQJ
SROOLQJ
7;&/.
7;$''5>@
7;&/$9
)
1
1
+LJK=
)
1
)
1
1
0
)
1
0
)
1
TXEN
7;'DWD>@
7;3$5,7<
3 3 +LJK=
3 3 3 .
+LJK=
7;62&
FHOO WUDQVPLVVLRQ WR
3 3+< 0
3+< 0
GUZ Figure 11 Utopia 2 Transmit Handshake - Transmission Suspended
19 of 47
September 21, 2001
IDT77V1254L25
VHOHFWLRQ
SROOLQJ
SROOLQJ
SROOLQJ
5;&/.
5;$''5>@
1
)
5;&/$9
1
)
1
1
1
)
+LJK=
1
)
1
1
)
1
RXEN
5;'DWD>@
5;3$5,7<
3 3 3 3 +LJK=
3 + + + XQGHILQHG
3 .
+LJK=
5;62&
3+< 1
3+< 1
FHOO WUDQVPLVVLRQ WR
GUZ Figure 12 Utopia 2 Receive Handshake - Back to Back Cells
VHOHFWLRQ
SROOLQJ
SROOLQJ
SROOLQJ
5;&/.
5;$''5>@
1
5;&/$9
)
1
1
+LJK=
)
1
)
1
1
1
)
1
)
+ + 1
RXEN
5;'DWD>@
5;3$5,7<
3 3 +LJK=
XQGHILQHG
FHOO WUDQVPLVVLRQ WR
.
+LJK=
5;62&
3+< 1
3+< 1
GUZ Figure 13 Utopia 2 Receive Handshake - Delay Between Cells
20 of 47
September 21, 2001
IDT77V1254L25
UHVHOHFWLRQ
SROOLQJ
SROOLQJ
SROOLQJ
5;&/.
5;$''5>@
1
)
5;&/$9
1
1
+LJK=
)
0
1
)
1
)
0
1
1
RXEN
5;'DWD>@
5;3$5,7<
3 3 +LJK=
3 3 3 3 +LJK=
5;62&
3+< 0
3+< 0
FHOO WUDQVPLVVLRQ IURP
GUZ .
Figure 14 Utopia 2 Receive Handshake - Suspended Transfer of Data
7;&/.
7;&/$9>@
TXEN>@
7;'$7$>@
7;3$5,7<
;
+
+
3
3
3
3
3
;
7;62&
GUZ .
Figure 15 Utopia 1 Transmit Handshake - Single Cell
7;&/.
7;&/$9>@
TXEN>@
7;'$7$>@
7;3$5,7<
3
3
3
+
+
+
+
;
+
7;62&
GUZ
GUZ Figure 16 Utopia 1 Transmit Handshake - Back-to-Back Cells, and TXEN Suspended Transmission
21 of 47
September 21, 2001
IDT77V1254L25
7;&/.
7;&/$9>@
TXEN>@
7;'$7$>@
7;3$5,7<
3
3
3
3
3
;
;
;
3
3
+
7;62&
GUZ .
Figure 17 Utopia 1 Transmit Handshake - TXEN Suspended Transmission and Back-to-Back Cells (Byte Mode Only)
5;&/.
5;&/$9>@
RXEN>@
5;'$7$>@
5;3$5,7<
3
+LJK=
3
+
+
+
+LJK=
5;62&
GUZ .
Figure 18 Utopia 1 Receive Handshake - Delay Between Cells
5;&/.
5;&/$9>@
RXEN>@
5;'$7$>@
5;3$5,7<
5;62&
3
3
+LJK=
+
3
3
;
;
+
+
+LJK=
GUZ .
Figure 19 Utopia 1 Receive Handshake - RXEN and RXCLAV Control
22 of 47
September 21, 2001
IDT77V1254L25
5;&/.
5;&/$9>@
(DUO\ 5[&/$9 RSWLRQ ELW UHJLVWHUV [ [ [ [
RXEN>@
5;'$7$>@
5;3$5,7<
3
+LJK=
3
3
3
3
3
3
;
+LJK=
;
+LJK=
5;62&
+LJK=
.
GUZ Figure 20 Utopia 1 Receive Handshake - RXCLAV Deassertion
5;&/.
5;&/$9>@
RXEN>@
5;'$7$>@
5;3$5,7<
+LJK=
5;62&
+LJK=
+
+
;
+
+
+
3
GUZ Figure 21 Utopia 1 Receive Handshake - RXCLAV Suspended Transfer (Byte Mode Only) Control and Status Interface
.
DPI Interface Option
The DPI interface is relatively new and worth additional description. The biggest difference between the DPI configurations and the UTOPIA configurations is that each channel has its own DPI interface. Each interface has a 4-bit data path, a clock and a start-of-cell signal, for both the transmit
direction and the receive direction. Therefore, each signal is point-to-point, and none of these signals has high-Z capability. Additionally, there is one
master DPI clock input (DPICLK) into the 77V1254L25 which is used as a source for the DPI transmit clock outputs. DPI is a cell-based transfer
scheme like Utopia Level 2, whereas UTOPIA Level 1 transfers can be either byte- or cell-based.
Another unique aspect of DPI is that it is a symmetrical interface. It is as easy to connect two PHYs back-to-back as it is to connect a PHY to a
switch fabric chip. In contrast, Utopia is asymmetrical. Note that for the 77V1254L25 the nomenclature "transmit" and "receive" is used in the naming
of the DPI signals, whereas other devices may use more generic "in" and "out" nomenclature for their DPI signals.
The DPI signals are summarized below, where "Pn_" refers to the signals for channel number "n":
DPICLK
input to PHY
Pn_TCLK
PHY to ATM
Pn_TD[3:0]
ATM to PHY
Pn_TFRM
ATM to PHY
Pn_RCLK
ATM to PHY
Pn_RD[3:0]
PHY to ATM
Pn_RFRM
PHY to ATM
23 of 47
September 21, 2001
IDT77V1254L25
In the transmit direction (ATM to PHY), the ATM layer device asserts start-of-cell signal (Pn_TFRM) for one clock cycle, one clock prior to driving
the first nibble of the cell on Pn_TD[3:0]. Once the ATM side has begun sending a cell, it is prepared to send the entire cell without interruption. The
77V1254L25 drives the transmit DPI clocks (Pn_TCLK) back to the ATM device, and can modulate (gap) it to control the flow of data. Specifically, if it
cannot accept another nibble, the 77V1254L25 disables Pn_TCLK and does not generate another rising edge until it has room for the nibble.
Pn_TCLK are derived from the DPICLK free running clock source.
The DPI protocol is exactly symmetrical in the receive direction, with the 77V1254L25 driving the data and start-of-cell signals while receiving
Pn_RCLK as an input.
The DPI data interface is four bits, so the 53 bytes of an ATM cell are transferred in 106 cycles. Figure 22 shows the sequence of that data transfer.
igures 23 through 30 show how the handshake operates.
%LW )LUVW
/DVW
%LW +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH +HDGHU E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH 3D\ORDG E\WH Figure 22 DPI Data Format and Sequence
3B5&/. LQ
3B5)50 RXW
3B5' RXW
;
;
&HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH ;
;
GUZ Figure 23 DPI Receive Handshake - One Cell Received
3B5&/. LQ
3B5)50 RXW
3B5' RXW
;
;
&HOO 1LEEOH &HOO 1LEEOH &HOO &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH GUZ Figure 24 DPI Receive Handshake - Back-to-Back Cells
24 of 47
.
September 21, 2001
IDT77V1254L25
3B5&/. LQ
3B5)50 RXW
3B5' RXW
&HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH GUZ Figure 25 DPI Receive Handshake - ATM Layer Device Suspends Transfer
.
$70 /D\HU 'HYLFH 1RW 5HDG\
9 1RW 5HDG\
3B5&/. LQ
3B5)50 RXW
3B5' RXW
&HOO 1LEEOH &HOO 1LEEOH ;
;
;
&HOO 1LEEOH &HOO 1LEEOH ;
&HOO 1LEEOH GUZ Figure 26 DPI Receive Handshake - Neither Device Ready
.
3B7&/. RXW
3B7)50 LQ
3B7' LQ
;
;
&HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH ;
;
Figure 27 DPI Transmit Handshake - One Cell for Transmission
3B7&/. RXW
3B7)50 LQ
3B7' LQ
;
;
&HOO 1LEEOH &HOO 1LEEOH &HOO &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH Figure 28 DPI Transmit Handshake - Back-to-Back Cells for Transmission
3B7&/. RXW
3B7)50 LQ
3B7' LQ
&HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH Figure 29 DPI Transmit Handshake - 77V1254L25 Transmit FIFO Full
25 of 47
September 21, 2001
IDT77V1254L25
9 1RW 5HDG\
$70 /D\HU 'HYLFH 1RW 5HDG\
3B7&/. RXW
3B7)50 LQ
3B7' LQ
&HOO 1LEEOH &HOO 1LEEOH ;
;
;
;
&HOO 1LEEOH &HOO 1LEEOH &HOO 1LEEOH GUZ .
Figure 30 DPI Transmit Handshake - Neither Device Ready
Control and Status Interface
Utility Bus
The Utility Bus is a byte-wide interface that provides access to the registers within the IDT77V1254L25. These registers are used to select desired
operating characteristics and functions, and to communicate status to external systems.
The Utility Bus is implemented using a multiplexed address and data bus (AD[7:0]) where the register address is latched via the Address Latch
Enable (ALE) signal.
The Utility Bus interface is comprised of the following pins: AD[7:0], ALE, CS, RD, WR
Read Operation
Refer to the Utility Bus timing waveforms in Figures 43 and 44. A register read is performed as follows:
1. Initial condition:
– RD, WR, CS not asserted (logic 1)
– ALE not asserted (logic 0)
2. Set up register address:
– place desired register address on AD[7:0]
– set ALE to logic 1;
– latch this address by setting ALE to logic 0.
3. Read register data:
– Remove register address data from AD[7:0]
– assert CS by setting to logic 0;
– assert RD by setting to logic 0
– wait minimum pulse width time (see AC specifications)
Write Operation
A register write is performed as described below:
1. Initial condition:
– RD, WR, CS not asserted (logic 1)
– ALE not asserted (logic 0)
2. Set up register address:
– place desired register address on AD[7:0]
– set ALE to logic 1;
– latch this address by setting ALE to logic 0.
3. Write data:
– place data on AD[7:0]
– assert CS by setting to logic 0;
– assert WR (logic 0) for minimum time (according to timing specification); reset WR to logic 1 to complete register write cycle.
Interrupt Operations
The IDT77V1254L25 provides a variety of selectable interrupt and signalling conditions which are useful both during ‘normal’ operation, and as
diagnostic aids. Refer to the Status and Control Register List section.
26 of 47
September 21, 2001
IDT77V1254L25
Overall interrupt control is provided via bit 0 of the Master Control Registers. When this bit is cleared (set to 0), interrupt signalling is prevented on
the respective port. The Interrupt Mask Registers allow individual masking of different interrupt sources. Additional interrupt signal control is provided
by bit 5 of the Master Control Registers. When this bit is set (=1), receive cell errors will be flagged via interrupt signalling and all other interrupt conditions are masked. These errors include:
‹ Bad receive HEC
‹ Short (fewer than 53 bytes) cells
‹ Received cell symbol error
Normal interrupt operations are performed by setting bit 0 and clearing bit 5 in the Master Control Registers. INT (pin 85) will go to a low state
when an interrupt condition is detected. The external system should then interrogate the 77V1254L25 to determine which one (or more) conditions
caused this flag, and reset the interrupt for further occurrences. This is accomplished by reading the Interrupt Status Registers. Decoding the bits in
these bytes will tell which error condition caused the interrupt. Reading these registers also:
‹
clears the (sticky) interrupt status bits in the registers that are read
‹
resets INT
This leaves the interrupt system ready to signal an alarm for further problems.
LED Control and Signaling
The LED outputs provide bi-directional LED drive capability of 8 mA. As an example, the RXLED outputs are described in the truth table:
State
Pin Voltage
Cells being received
Low
Cells not being received
High
As illustrated in the following drawing (Figure 31), this could be connected to provide for a two-LED condition indicator. These could also be
different colors to provide simple status indication at a glance. (The minimum value for R should be 330Ω).
TXLED Truth Table
State
Pin Voltage
Cells being transmitted
Low
Cells not being transmitted High
Diagnostic Function
9
5
,QGLFDWHV &HOOV
EHLQJ UHFHLYHG RU
WUDQVPLWWHG
5[/('
7[/('
,QGLFDWHV &HOOV DUH
QRW EHLQJ UHFHLYHG RU
WUDQVPLWWHG
5
GUZ Figure 31 LED Indicator
27 of 47
September 21, 2001
IDT77V1254L25
Loopback
There are two loopback modes supported by the 77V1254L25. The loopback mode is controlled via bits 1 and 0 of the Diagnostic Control Registers:
Bit 1
Bit 0
Mode
0
0
Normal operating mode
1
0
PHY Loopback
1
1
Line Loopback
Normal Mode
This mode, Figure 32, supports normal operating conditions: data to be transmitted is transferred to the TC, where it is queued and formatted for
transmission by the PMD. Receive data from the PMD is decoded along with its clock for transfer to the receiving "upstream system".
PHY Loopback
As Figure 33 illustrates below, this loopback mode provides a connection within the PHY from the transmit PHY-ATM interface to the PHY-ATM
receive interface. Note that while this mode is operating, no data is forwarded to or received from the line interface. Line Loopback
Line Loopback
Figure 34 might also be called “remote loopback” since it provides for a means to test the overall system, including the line. Since this mode will
probably be entered under direction from another system (at a remote location), receive data is also decoded and transferred to the upstream system
to allow it to listen for commands. A common example would be a command asking the upstream system to direct the TC to leave this loopback state,
and resume normal operations.
77V1254L25
,'79
$70 /D\HU 'HYLFH
7& VXEOD\HU
30' VXEOD\HU
/LQH
,QWHUIDFH
GUZ Figure 32 Normal Mode
,'79
77V1254L25
$70 /D\HU 'HYLFH
7& VXEOD\HU
30' VXEOD\HU
/LQH
,QWHUIDFH
GUZ Figure 33 PHY Loopback
28 of 47
September 21, 2001
IDT77V1254L25
77V1254L25
,'79
$70 /D\HU 'HYLFH
7& VXEOD\HU
30'
VXEOD\HU
/LQH
,QWHUIDFH
GUZ Figure 34 Line Loopback
Counters
Several condition counters are provided to assist external systems (e.g., software drivers) in evaluating communications conditions. It is anticipated that these counters will be polled from time to time (user selectable) to evaluate performance. A separate set of registers exists for each channel
of the PHY.
‹ Symbol Error Counters
– 8 bits
– counts all invalid 5-bit symbols received
‹ Transmit Cell Counters
– 16 bits
– counts all transmitted cells
‹ Receive Cell Counters
– 16 bits
– counts all received cells, excluding idle cells and HEC errored cells
‹ Receive HEC Error Counters
– 5 bits
– counts all HEC errors received
The TXCell and RXCell counters are sized (16 bits) to provide a full cell count (without roll over) if the counter is read once/second. The Symbol
Error counter and HEC Error counter were given sufficient size to indicate exact counts for low error-rate conditions. If these counters overflow, a
gross condition is occurring, where additional counter resolution does not provide additional diagnostic benefit.
Reading Counters
1. Decide which counter value is desired. Write to the Counter Select Register(s) (0x06, 0x16, 0x26 and 0x36) to the bit location corresponding
to the desired counter. This loads the High and Low Byte Counter Registers with the selected counter’s value, and resets this counter to zero.
2.
Note: Only one counter may be enabled at any time in each of the Counter Select Registers.
Read the Counter Registers (0x04, 0x14, 0x24 or 0x34 (low byte)) and (0x05, 0x15, 0x25 or 0x35 (high byte)) to get the value.
Further reads may be accomplished in the same manner by writing to the Counter Select Registers.
Note: The PHY takes some time to set up the low and high byte counters after a specific counter has been selected in the Counter Selector
register. This time delay (in µS) varies with the line rate and can be calculated as follows:
Time delay (µS) =
12.5___
line rate (Mbps)
Loop Timing Feature
The 77V1254L25 also offers a loop timing feature for specific applications where data needs to be repeated / transmitted using the recovered
clock. If the loop timing mode is enabled in the Enhanced Control Register 1 bit 6, the recovered receive clock is used as to clock out data on transmit
side. This mode is port specific, i.e., the user can select one or more ports to be in loop timing mode. In normal mode, the transmitter transmits data
using the multiplied oscillator clock.
29 of 47
September 21, 2001
IDT77V1254L25
Jitter in Loop Timing Mode
One of the primary concerns when using loop timing mode is the amount of jitter that gets added each time data is transmitted. Table 3 shows the
jitter measured at various data rates. The set-up shown in Figure 35 was used to perform these tests. The maximum jitter seen was at TX point 5 and
the minimum jitter was at point 2. The loop timing jitter is defined as the amount of jitter generated by each TX node. In other words, the loop timing
jitter or the jitter added by a loop-timed port in the set-up below is the difference between the Total Output Jitter and the Total Input Jitter.
OSC
1
2
RX
TX
TX
RX
P0
Data
CLK
Data
P1
Loop Timing Mode
Normal Mode
3
RX
TX
Data
CLK
P2
Loop Timing Mode
Data
4
RX
TX
5
Data
CLK
P3
Loop Timing Mode
Data
SWITCH
Figure 35 Test Setup for Loop Timing Jitter Measurements
Loop Timing Jitter Specification
Line Rate
Mbps
Data Rate
Mbps
Min.
Typ.
Max.
Note
32
25.6
--
100 ps
--
Using 32Mhz OSC
64
51.2
--
100 ps
--
Using 64Mhz OSC
Table 3 Loop Timing Jitter
The waveforms below show some of the measurements taken with the set-up in Figure 35. Using the formula above, the jitter specification was
derived. For example, at data rate of 25.6Mbps, jitter added going through Line Card 3 is 1.5ns -1.4ns (as shown in the waveforms below).
30 of 47
September 21, 2001
IDT77V1254L25
Jitter at 25.6Mbps at point 5 with respect to point 1
Jitter at 25.6Mbps at point 4 with respect to point 1
Jitter at 51.2Mbps at point 4 with respect to point 1
Jitter at 51.2Mbps at point 5 with respect to point 1
From the above measurements taken, the amount of jitter being added at each TX point is not significant. These tests were also run for extended
periods of time (64 hours) and no bit errors were seen.
VPI/VCI Swapping
For compatibility with IDT's SwitchStar products (77V400 and 77V500), the 77V1254L25 has the ability to swap parts of the VPI/VCI address
space in the header of receive cells. This function is controlled by the VPI/VCI Swap bits, which are bit 5 of the Enhanced Control Registers (0x08,
0x18, 0x28 and 0x38). The portions of the VPI/VCI that are swapped are shown below. Bits X(7:0) are swapped with Y(7:0) when the VPI/VCI Swap
bit is set and the chip is in DPI mode.
93,
9&,
*)&93,
93,
37,
+(&
;
;
;
;
%\WH %\WH 9&,
9&,
%\WH <
&/3 %\WH %\WH <
<
<
;
;
;
;
%\WH <
<
<
<
%\WH %\WH %\WH %\WH 31 of 47
September 21, 2001
IDT77V1254L25
Line Side (Serial) Interface
Each of the four ports has two pins for differential serial transmission, and two pins for differential serial receiving.
PHY to Magnetics Interface
A standard connection to 100Ω and 120Ω unshielded twisted pair cabling is shown in Figure 36. Note that the transmit signal is somewhat attenuated in order to meet the launch amplitude specified by the standards. The external receive circuitry is designed to attenuate low frequencies in order
to compensate for the high frequency attenuation of the cable.
Also, the receive circuitry biases the positive and negative RX inputs to slightly different voltages. This is done so that the receiver does not receive
false signals in the absence of a real signal. This can be important because the 77V1254L25 does not disable error detection or interrupts when an
input signal is not present.
When connecting to UTP at 51.2 Mbps, it is necessary to use magnetics with sufficient bandwidth. Such a device can also operate satisfactorily at
25.6 Mbps. Refer to Table 5 for the recommended magnetics.
$*1'
5- &RQQHFWRU
7['
5
0DJQHWLFV
,'79
,'79
5
5
&
7['
$9''
5
5['
5
5
5
5
/
5['
&
5
$*1'
$*1'
.
GUZ Figure 36 Recommended Connection to Magnetics
Component
Value
Tolerance
R1
47Ω
±5%
R2
47Ω
±5%
R3
620Ω
±5%
R4
110Ω
±5%
R5
2700Ω
±5%
R6
2700Ω
±5%
R7
82Ω
±5%
R8
33Ω
±5%
R9
33Ω
±5%
Table 4 Analog Component Values (Part 1 of 2)
32 of 47
September 21, 2001
IDT77V1254L25
Component
Value
Tolerance
C1
470pF
±20%
C2
470pF
±20%
L1
3.3µH
±20%
Table 4 Analog Component Values (Part 2 of 2)
Magnetics Modules for 25.6 Mbps
Pulse PE-67583 or R4005
www.pulseeng.com
TDK TLA-6M103
www.component.tdk.com
Magnetics Module for 51.2 Mbps
Pulse R4005
www.pulseeng.com
Table 5 Magnetics Modules
Status and Control Register List
The 77V1254L25 has 37 registers that are accessible through the utility bus. Each of the four ports has 9 registers dedicated to that port. There is
only one register (0x40) which is not port specific.
For those register bits which control operation of the Utopia interface, the operation of the Utopia interface is determined by the registers corresponding to the port which is selected at that particular time. For consistent operation, the Utopia control bits should be programmed the same for all
four ports, except for the Utopia 2 port addresses in the Enhanced Control Registers.
Register Name
Register Address
Port 0
Port 1
Port 2
Port 3
Master Control Registers
0x00
0x10
0x20
0x30
Interrupt Status Registers
0x01
0x11
0x21
0x31
Diagnostic Control Registers
0x02
0x12
0x22
0x32
LED Driver and HEC Status/control
0x03
0x13
0x23
0x33
Low Byte Counter Register [7:0]
0x04
0x14
0x24
0x34
High Byte Counter Register [15:8]
0x05
0x15
0x25
0x35
Counter Registers Read Select
0x06
0x16
0x26
0x36
Interrupt Mask Registers
0x07
0x17
0x27
0x37
Enhanced Control 1 Registers
0x08
0x18
0x28
0x38
RXREF and TXREF Control Register
Nomenclature
"Reserved" register bits, if written, should always be written "0"
R-only or W-only = register is read-only or write-only
“0” = ‘cleared’ or ‘not set’
All Ports
0x40
R/W = register may be read and written via the utility bus
sticky = register bit is cleared after the register containing it is read; all sticky bits are read-only
“1” = ‘set’
33 of 47
September 21, 2001
IDT77V1254L25
Master Control Registers
Addresses: 0x00, 0x10, 0x20, 0x30
Bit
Type
Initial State
Function
7
R/W
0
Reserved
6
R/W
1 = discard errored cells Discard Receive Error Cells - On receipt of any cell with an error (e.g. short cell, invalid command mnemonic, receive
HEC error (if enabled), this cell will be discarded and will not enter the receive FIFO.
5
R/W
0 = all interrupts
Enable Cell Error Interrupts Only - If Bit 0 in this register is set (Interrupts Enabled), setting of this bit enables only
"Received Cell Error" (as defined in bit 6) to trigger interrupt line.
4
R/W
0 = disabled
Transmit Data Parity Check - Directs TC to check parity of TXDATA against parity bit located in TXPARITY.
3
R/W
1 = discard idle cells
Discard Received Idle Cells - Directs TC to discard received idle (VPI/VCI = 0) cells from PMD without signalling
external systems.
2
R/W
0 = not halted
Halt Transmit - Halts transmission of data from TC to PMD and forces the TXD outputs to the "0" state
1
R/W
0 = cell mode
UTOPIA Level 1 mode select: - 0 = cell mode, 1 = byte mode. Not applicable for Utopia 2 or DPI modes.
0
R/W
1 = enable interrupts
Enable Interrupt Pin (Interrupt Mask Bit) - Enables interrupt output pin (pin 85). If cleared, pin is always high and
interrupt is masked. If set, an interrupt will be signaled by setting the interrupt pin to "0". It doesn’t affect the Interrupt
Status Registers.
Interrupt Status Registers
Addresses: 0x01, 0x11, 0x21, 0x31
Bit
Type
7
Initial State
Function
Reserved
6
R
0 = Bad Signal
Good Signal Bit - See definition on page 13.
1 - Good Signal
0 - Bad Signal
5
sticky
0
HEC error cell received - Set when a HEC error is detected on received cell.
4
sticky
0
"Short Cell" Received - Interrupt signal which flags received cells with fewer than 53 bytes. This condition is detected
when receiving Start-of-Cell command bytes with fewer than 53 bytes between them.
3
sticky
0
Transmit Parity Error - If Bit 4 of Register 0x00 / 0x10 / 0x20 / 0x30 is set (Transmit Data Parity Check), this interrupt
flags a transmit data parity error condition. Odd parity is used.
2
sticky
0
Receive Signal Condition change - This interrupt is set when the received ’signal’ changes either from ’bad to good’
or from ’good to bad’.
1
sticky
0
Received Symbol Error - Set when an undefined 5-bit symbol is received.
0
sticky
0
Receive FIFO Overflow - Interrupt which indicates when the receive FIFO has filled and cannot accept additional data.
Diagnostic Control Registers
Addresses: 0x02, 0x12, 0x22, 0x32
Bit
7
Type
R/W
Initial State
0 = normal
Function
Force TXCLAV deassert - (applicable only in Utopia 1 and 2 modes) Used during line loopback mode to prevent
upstream system from continuing to send data to the 77V1254L25.
34 of 47
September 21, 2001
IDT77V1254L25
Addresses: 0x02, 0x12, 0x22, 0x32
Bit
Type
Initial State
Function
6
R/W
0 = UTOPIA
RXCLAV Operation Select - (for Utopia 1 mode) The UTOPIA standard dictates that during cell mode operation, if the
receive FIFO no longer has a complete cell available for transfer from PHY, RXCLAV is deasserted following transfer of
the last byte out of the PHY to the upstream system. With this bit set, early deassertion of this signal will occur coincident with the end of Payload byte 44 (as in octet mode for TXCLAV). This provides early indication to the upstream
system of this impending condition.
0 = "Standard UTOPIA RXCLAV’
1 = "Cell mode = Byte mode"
5
R/W
1 = tri-state
Single/Multi-PHY configuration select - (applicable and writable only in Utopia 1 mode)
0 = single:
Never tri-state RXDATA, RXPARITY and RXSOC
1 = Multi-PHY mode: Tri-state RXDATA, RXPARITY and RXSOC when RXEN = 1
4
R/W
0 = normal
RFLUSH = Clear Receive FIFO - This signal is used to tell the TC to flush (clear) all data in the receive FIFO. The TC
signals this completion by clearing this bit.
3
R/W
0 = normal
Insert Transmit Payload Error - Tells TC to insert cell payload errors in transmitted cells. This can be used to test
error detection and recovery systems at destination station, or, under loopback control, at the local receiving station.
This payload error is accomplished by flipping bit 0 of the last cell payload byte.
2
R/W
0 = normal
Insert Transmit HEC Error - Tells TC to insert HEC error in Byte 5 of cell. This can be used to test error detection and
recovery systems in downstream switches, or, under loopback control, the local receiving station. The HEC error is
accomplished by flipping bit 0 of the HEC byte.
1,0
R/W
00 = normal
Loopback Control
bit # 1
0
0
0 Normal mode (receive from network)
1
0 PHY Loopback
1
1 Line Loopback
LED Driver and HEC Status/Control Registers
Addresses: 0x03, 0x13, 0x23, 0x33
Bit
Type
7
Initial State
Function
0
Reserved
6
R/W
0 = enable checking
Disable Receive HEC Checking (HEC Enable) - When not set, the HEC is calculated on first 4 bytes of received cell,
and compared against the 5th byte. When set (= 1), the HEC byte is not checked.
5
R/W
0 = enable calculate &
replace
Disable Transmit HEC Calculate & Replace - When set, the 5th header byte of cells queued for transmit is not
replaced with the HEC calculated across the first four bytes of that cell.
4, 3
R/W
00 = 1 cycle
RXREF Pulse Width Select
bit # 4
3
0
0 RXREF active for 1 OSC cycle
0
1 RXREF active for 2 OSC cycles
1
0 RXREF active for 4 OSC cycles
1
1 RXREF active for 8 OSC cycles
2
R
1 = empty
FIFO Status
1 = TxFIFO empty
1
R
1
TXLED Status
0 = Cell Transmitted
1 = Cell Not Transmitted
0
R
1
RXLED Status
0 = Cell Received
1 = Cell Not Received
35 of 47
0 = TxFIFO not empty
September 21, 2001
IDT77V1254L25
Low Byte Counter Registers [7:0]
Addresses: 0x04, 0x14, 0x24, 0x34
Bit
[7:0]
Type
R
Initial State
0x00
Function
Provides low byte of counter value selected via registers 0x06, 0x16, 0x26, and 0x36
High Byte Counter Registers [15:8]
Addresses: 0x05, 0x15, 0x25, 0x35
Bit
[7:0]
Type
R
Initial State
0x00
Function
Provides high-byte of counter value selected via registers 0x06, 0x16, 0x26, and 0x36
Counter Select Registers
Addresses: 0x06, 0x16, 0x26, 0x36
Bit
Type
Initial State
Function
7
—
—
Reserved.
6
—
—
Reserved.
5
—
—
Reserved.
4
—
—
Reserved.
3
W
0
Symbol Error Counter.
2
W
0
TXCell Counter.
1
W
0
RXCell Counter. Cells with HEC errors are never counted.
0
W
0
Receive HEC Error Counter.
Note: For proper operation, only one bit may be set in a Counter Select Register at any time.
Interrupt Mask Registers
Addresses: 0x07, 0x17, 0x27, 0x37
Bit
Type
Initial State
Function
7
0
Reserved.
6
0
Reserved.
5
R/W
0 = interrupt enabled
HEC Error Cell.
4
R/W
0 = interrupt enabled
Short Cell Error.
3
R/W
0 = interrupt enabled
Transmit Parity Error.
2
R/W
0 = interrupt enabled
Receive Signal Condition Change.
1
R/W
0 = interrupt enabled
Receive Cell Symbol Error.
0
R/W
0 = interrupt enabled
Receive FIFO Overflow.
Note: When set to "1", these bits mask the corresponding interrupts going to the interrupt pin (INT). When set to "0", the interrupts are
unmasked. These interrupts correspond to the interrupt status bits in the Interrupt Status Registers.
36 of 47
September 21, 2001
IDT77V1254L25
Enhanced Control 1 Registers
Addresses: 0x08, 0x18, 0x28, 0x38
Bit
Type
Initial State
Function
7
W
0 = not reset
Individual Port Software Reset 1= Reset. This bit is self-cleaning; It isn’t necessary to write “0” to exit reset.
6
R/W
0 = OSC
Transmit Line Clock (or Loop Timing Mode). When set to 0, the OSC input is used as the transmit line clock.
When set to 1, the recovered receive clock is used as the transmit line clock.
5
R/W
0
Reserved
4-0
R/W
Port 0 (Reg 0x08) 00000
Port 1 (Reg 0x18) 00001
Port 2 (Reg 0x28) 00010
Port 3 (Reg 0x38) 00011
Utopia 2 Port Address When operating in Utopia 2 Mode, these register bits determine the Utopia 2 port address
RXREF and TXREF Control Register
Addresses: 0x40
Bit
7-6
5
Type
R/W
W
4
3-0
Initial State
0 = RXREF0 (Port 0) RXREF Source Select Selects which of the four ports (0-3) is the source of RXREF.
0 = not reset
0
R/W
Function
Master Software Reset 1 = Reset. This bit is self-cleaning; it isn’t necessary to write “0” to exit reset.
Reserved
0000 = not looped
RXREF to TXREF Loop Select When set to 0, TXREF is used to generate X_8 timing marker commands.
When set to 1, TXREF input is ignored, and received X_8 timing commands.
are looped back and added to the transmit stream of that same port. See Figure 7.
bit 3: port 3
bit 2: port 2
bit 1: port 1
bit 0: port 0
Absolute Maximum Ratings
Symbol
Rating
Value
Unit
VTERM
Terminal Voltage with Respect to GND
-0.5 to +5.5
V
TBIAS
Temperature Under Bias
-55 to +125
°C
TSTG
Storage Temperature
-55 to +120
°C
IOUT
DC Output Current
50
mA
Note: Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
37 of 47
September 21, 2001
IDT77V1254L25
Recommended DC Operating Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
VDD
Digital Supply Voltage
3.0
3.3
3.6
V
GND
Digital Ground Voltage
0
0
0
V
VIH
Input High Voltage
2.0
____
5.25
V
VIL
Input Low Voltage
-0.3
____
0.8
V
AVDD
Analog Supply Voltage
3.0
3.3
3.6
V
AGND
Analog Ground Voltage
0
0
0
V
VDIF
VDD - AVDD
-0.5
0
0.5
V
Capacitance (TA = +25°C, F = 1MHz)
Symbol
Parameter
Conditions
Max.
Unit
CIN1
Input Capacitance
VIN = 0V
10
pF
CIO1
I/O Capacitance
VOUT = 0V
10
pF
1. Characterized values, not tested.
DC Electrical Characteristics (All Pins except TX+/- and RX+/-)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
ILI
Input Leakage Current
Gnd ≤ VIN ≤ VDD
-5
5
µA
ILO
/O (as input) Leakage Current
Gnd ≤ VIN ≤ VDD
-10
10
µA
1
OH1
Output Logic "1" Voltage
IOH = -2mA, VDD = min.
2.4
—
V
2
OH2
V
Output Logic "1" Voltage
IOH = -8mA, VDD = min.
2.4
—
V
VOL3
Output Logic "0" Voltage
IOL = -8mA, VDD = min.
—
0.4
V
4, 5
DD1
Digital Power Supply Current - VDD
OSC = 32 MHz, all outputs unloaded
—
90
mA
OSC = 64 MHz, all outputs unloaded
—
170
mA
OSC = 32 MHz, all outputs unloaded
—
55
mA
OSC = 64 MHz, all outputs unloaded
—
60
mA
V
I
5
DD2
I
Analog Power Supply Current - AVDD
1.
For AD[7:0] pins only.
2.
For all output pins except AD[7:0], INT and TX+/-.
3.
For all output pins except TX+/-.
4.
Add 15mA for each TX+/- pair that is driving a load.
5.
Total supply current is the sum of IDD1 and IDD2
38 of 47
September 21, 2001
IDT77V1254L25
DC Electrical Characteristics (TX+/- Output Pins Only)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
VOH1
Output Logic High Voltage
IOH = -20mA
VDD - 0.5V
—
V
VOL
Output Logic Low Voltage
IOL = -20mA
—
0.5
V
DC Electrical Characteristics (RXD+/- Input Pins Only)
Symbol
Parameter
Min.
Typ
Max.
Unit
VIR
RXD+/- input voltage range
0
—
VDD
V
VIP
RXD+/- input peak-to-peak differential voltage
0.6
—
2*VDD
V
VICM
RXD+/- input common mode voltage
1.0
VDD/2
VDD-0.5
V
UTOPIA Level 2 Bus Timing Parameters
Symbol
Parameter
Min.
Max.
Unit
t1
TXCLK Frequency
0.2
50
MHz
t2
TXCLK Duty Cycle (% of t1)
40
60
%
t3
TXDATA[15:0], TXPARITY Setup Time to TXCLK
4
—
ns
t4
TXDATA[15:0], TXPARITY Hold Time to TXCLK
1.5
—
ns
t5
TXADDR[4:0], Setup Time to TXCLK
4
—
ns
t6
TXADDR[4:0], Hold Time to TXCLK
1.5
—
ns
t7
TXSOC, TXEN Setup Time to TXCLK
4
—
ns
t8
TXSOC, TXEN Hold Time to TXCLK
1.5
—
ns
t9
TXCLK to TXCLAV High-Z
2
10
ns
t10
TXCLK to TXCLAV Low-Z (min) and Valid (max)
2
10
ns
t12
RXCLK Frequency
0.2
50
MHz
t13
RXCLK Duty Cycle (% of t12)
40
60
%
t14
RXEN Setup Time to RXCLK
4
—
ns
t15
RXCLK Hold Time to RXCLK
1.5
—
ns
t16
RXADDR[4:0] Setup Time to RXCLK
4
—
ns
t17
RXADDR[4:0] Hold Time to RXCLK
1.5
—
ns
t18
RXCLK to RXCLAV High-Z
2
10
ns
t19
RXCLK to RXCLAV Low-Z (min) and Valid (max)
2
10
ns
t20
RXCLK to RXSOC High-Z
2
10
ns
t21
RXCLK to RXSOC Low-Z (min) and Valid (max)
2
10
ns
t22
RXCLK to RXDATA, RXPARITY High-Z
2
10
ns
t23
RXCLK to RXDATA, RXPARITY Low-Z (min) and Valid (max)
2
10
ns
39 of 47
September 21, 2001
IDT77V1254L25
W
W
W
W
7;&/.
7;'$7$>@
7;3$5,7<
2FWHW W
W
W
W
2FWHW 7;$''5>@
W
W
7;62&
W
TXEN
7;&/$9
+LJK=
+LJK=
GUZ Figure 37 UTOPIA Level 2 Transmit
W
W
5;&/.
W
W
W
W
RXEN
5;$''5>@
W
5;&/$9
5;62&
5;'$7$>@
5;3$5,7<
+LJK=
+LJK=
W
W
+LJK=
+LJK=
W
W
W
W
W
W
+LJK=
+LJK=
GUZ Figure 38 UTOPIA Level 2 Receive
.
UTOPIA Level 1 Bus Timing Parameters
Symbol
Parameter
Min.
Max.
Unit
t31
TXCLK Frequency
0.2
50
MHz
t32
TXCLK Duty Cycle (% of t31)
40
60
%
t33
TXDATA[7:0], TXPARITY Setup Time to TXCLK
4
—
ns
t34
TXDATA[7:0], TXPARITY Hold Time to TXCLK
1.5
—
ns
t35
TXSOC, TXEN[3:0] Setup Time to TXCLK
4
—
ns
t36
TXSOC, TXEN[3:0] Hold Time to TXCLK
1.5
—
ns
t37
TXCLK to TXCLAV[3:0] Invalid (min) and Valid (max)
2
10
ns
t39
RXCLK Frequency
0.2
50
MHz
t40
RXCLK Duty Cycle (% of t39)
40
60
%
t41
RXEN[3:0] Setup Time to RXCLK
4
—
ns
40 of 47
September 21, 2001
IDT77V1254L25
Symbol
Parameter
Min.
Max.
Unit
t42
RXEN[3:0] Hold Time to RXCLK
1.5
—
ns
t43
RXCLK to RXCLAV[3:0] Invalid (min) and Valid (max)
2
10
ns
t44
RXCLK to RXSOC High-Z
2
10
ns
t45
RXCLK to RXSOC Low-Z (min) and Valid (max)
2
10
ns
t46
RXCLK to RXDATA, RXPARITY High-Z
2
10
ns
t47
RXCLK to RXDATA, RXPARITY Low-Z (min) and Valid (max)
2
10
ns
W
W
W
W
7;&/.
7;'$7$>@
7;3$5,7<
2FWHW W
2FWHW W
W
7;62&
TXEN[3:0]
7;&/$9>@
GUZ Figure 39 UTOPIA Level 1 Transmit
W
W
5;&/.
W
W
RXEN[3:0]
W
5;&/$9>@
5;62&
+LJK=
5;'$7$>@
5;3$5,7<
+LJK=
W
W
W
W
W
W
+LJK=
+LJK=
GUZ Figure 40 UTOPIA Level 1 Receive
DPI Bus Timing Parameters
Symbol
Parameter
Min.
Max.
Unit
t51
DPICLK Frequency
0.2
50
MHz
t52
DPICLK Duty Cycle (% of t51)
40
60
%
t53
DPICLK to Pn_TCLK Propagation Delay
2
14
ns
t54
Pn_TFRM Setup Time to Pn_TCLK
4
—
ns
t55
Pn_TFRM Hold Time to Pn_TCLK
1
—
ns
t56
Pn_TD[3:0] Setup Time to Pn_TCLK
4
—
ns
t57
Pn_TD[3:0] Hold Time to Pn_TCLK
1
—
ns
41 of 47
September 21, 2001
IDT77V1254L25
Symbol
Parameter
Min.
Max.
Unit
t61
Pn_RCLK Period
25
—
ns
t62
Pn_RCLK High Time
10
—
ns
t63
Pn_RCLK Low Time
10
—
ns
t64
Pn_RCLK to Pn_TFRM Invalid (min) and Valid (max)
2
12
ns
t65
Pn_RCLK to Pn_RD Invalid (min) and Valid (max)
2
12
ns
W
W
'3,&/.
W
3QB7&/.
W
W
3QB7)50
W
W
3QB7'>@
GUZ .
Figure 41 DPI Transmit
W
W
W
3QB5&/.
W
3QB5)50
W
3QB5'>@
GUZ .
Figure 42 DPI Receive
Utility Bus Read Cycle
Name
Min.
Max.
Unit
Description
Tas
10
—
MHz
Address setup to ALE
Tcsrd
0
—
%
Chip select to read enable
Tah
5
—
ns
Address hold to ALE
Tapw
10
—
ns
ALE min pulse width
Ttria
0
—
ns
Address tri-state to RD assert
42 of 47
September 21, 2001
IDT77V1254L25
Name
Min.
Max.
Unit
Description
Trdpw
20
—
ns
Min. RD pulse width
Tdh
0
—
ns
Data Valid hold time
Tch
0
—
ns
RD deassert to CS deassert
Ttrid
—
10
ns
RD deassert to data tri-state
Trd
—
18
ns
Read Data access
Tar
5
—
ns
ALE low to start of read
Trdd
0
—
ns
Start of read to Data low-Z
Min.
Max.
Utility Bus Write Cycle
Name
$'>@
LQSXW
Unit
Description
Tapw
10
—
ns
ALE min pulse widt
Tas
10
—
ns
Address set up to ALE
Tah
5
—
ns
Address hold time to ALE
Tcswr
0
—
ns
CS Assert to WR
Twrpw
20
—
ns
Min. WR pulse width
Tdws
20
—
ns
Write Data set up
Tdwh
10
—
ns
Write Data hold time
Tch
0
—
ns
WR deassert to CS deassert
Taw
20
—
ns
ALE low to end of write
7DV
7DK
$GGUHVV
7DSZ
$/(
7FK
7FVUG
CS
7DU
7UGSZ
7WULG
RD
7GK
7UG
7UGG
$'>@
RXWSXW
'DWD
GUZ Figure 43 Utility Bus Read Cycle
43 of 47
September 21, 2001
IDT77V1254L25
7DV
$'>@
7DK
7GZV
7GZK
'DWD LQSXW
$GGUHVV
7DSZ
$/(
7FK
7DZ
CS
7FVZU
7ZUSZ
WR
GUZ .
Figure 44 Utility Bus Write Cycle
OSC, RXREF, TXREF and Reset Timing
Symbol
Parameter
Min.
Typ.
Max.
Unit
Tcyc
OSC cycle period
30
15
31.25
15.625
33
16.5
ns
ns
Tch
OSC high tim
40
—
60
%
Tcl
OSC low time
40
—
60
%
OSC cycle to cycle period variation
—
—
1
%
Trrpd
OSC to RXREF Propagation Delay
1
—
30
ns
Ttrh
TXREF High Time
35
—
—
ns
Ttrl
TXREF Low Time
35
—
—
ns
Trspw
Minimum RST Pulse Width
two OSC cycles
—
—
—
Tcc
1
1. The width of the RXREF pulse is programmable in the LED Driver and HEC Status/Control Registers.
7FK
7F\F
7FO
26&
7UUSG
7UUSG
RXREF
7WUO
7WUK
TXREF
7UVSZ
RST
GUZ .
Figure 45 OSC, RXREF, TXREF and Reset Timing
44 of 47
September 21, 2001
IDT77V1254L25
AC Test Conditions
Input Pulse Levels
GND to 3.0V
Input Rise/Fall Times
3ns
Input Timing Reference Levels
1.5V
Output Reference Levels
1.5V
Output Load
See Figure 46
3.3V
1.2KΩ
D.U.T.
30pF*
900Ω
* Includes jig and scope capacitances.
Figure 46 Output Load
A note about Figures 47 and 48: The ATM Forum and ITU-T standards for 25 Mbps ATM define "Network" and "User" interfaces. They are identical
except that transmit and receive are switched between the two. A Network device can be connected directly to a User device with a straight-through
cable. User-to-User or Network-to-Network connections require a cable with 1-to-7 and 2-to-8 crossovers.
1RWH 1RWH 5[ 5-
&RQQHFWRU
7[
$*1'
5[
)LOWHU
1RWH $*1'
5-
0DJQHWLFV
5-
0DJQHWLFV
5-
0DJQHWLFV
7; 7;
5;
5;
0DJQHWLFV
7[
)LOWHU
,'7
77V1254L25
9
1RWH GUZ .
Figure 47 PC Board Layout for ATM Network
Note: 1.No power or ground plane inside this area.
2.Analog power plane inside this area.
3.Digital power plane inside this area.
4.A single ground plane should extend over the area covered by the analog and digital power planes, without breaks.
5.All analog signal traces should avoid 90° corners.
45 of 47
September 21, 2001
IDT77V1254L25
1RWH 1RWH $*1'
7[ 5-
&RQQHFWRU
5[ 1RWH 7[
)LOWHU
7; 7;
0DJQHWLFV
5-
0DJQHWLFV
5-
0DJQHWLFV
5-
0DJQHWLFV
5;
5;
5[
)LOWHU
$*1'
1RWH ,'7
9
77V1254L25
.
GUZ Figure 48 PC Board Layout for ATM User
Note: 1.No power or ground plane inside this area.
2.Analog power plane inside this area.
3.Digital power plane inside this area.
4.A single ground plane should extend over the area covered by the analog and digital power planes, without breaks.
5.All analog signal traces should avoid 90° corners.
Package Dimensions
$
$
.
H
3LQ
34)3
( (
4.3514 '5.4035 '
$
'
4.4319 '
2.4792 '
'
5.5125 '
/
6<0%2/
0,1
120
0$;
$
$
$
'
'
(
(
H
E
/
E
'LPHQVLRQV DUH LQ PLOOLPHWHUV
GUZ PSC-4053 is a more comprehensive package outline drawing and is available from the packaging section of the IDT web site.
46 of 47
September 21, 2001
IDT77V1254L25
Ordering Information
,'7
11111
'HYLFH 7\SH
$
111
$
$
3RZHU
6SHHG
3DFNDJH
3URFHVV
7HPS 5DQJH
%ODQN
,
&RPPHUFLDO ƒ& WR ƒ&
,QGXVWULDO ƒ& WR ƒ&
3*
3LQ 34)3 38
0EV
/
77V1254L25
9 4XDG 0EV $70 3+<
7UDQVPLVVLRQ &RQYHUJHQFH 7&
DQG 30' 6XEOD\HUV
GUZ .
Revision History
3/2/98:
ADVANCE INFORMATION. Initial Draft.
10/5/98
PRELIMINARY. TXOSC pin name changed to OSC. Missing information added. Package code corrected in ordering code.
11/30/98
PRELIMINARY. Numerous minor edits. Corrections to Figures 26 and 30. Elimination of Line Rate Selection bit in the Master Control
Registers. IDD1 and IDD2 values updated. Addition of VPI/VCI Swap feature. Improvements to Utopia bus timing parameters.
3/23/99:
Update to new format, revisions to Utopia 1 text.
3/8/01
Changed from Preliminary to Final. Various typographic corrections. Corrected default values for UTOPIA 2 Port Address in the
Enhanced Control 1 Registers. Added IDD values for 51 Mbps.Removed Trd minimum spec. IDD Values for 25 Mbps and 51 Mbps
updated.
9/21/2001
Changed values in the Max. column for IDD1 and IDD2 in the DC Electrical Characteristics (All pins except TX and RX) table.
Changed value in Max. column for t23 in Utopia Level 2 Bus Timing Parameters table. Added Loop Timing Feature section.
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-330-1748
www.idt.com
47 of 47
for Tech Support:
email: [email protected]
phone: 408-330-1752
September 21, 2001