IDT IDT82V2082PF

DUAL CHANNEL T1/E1/J1 LONG HAUL/
SHORT HAUL LINE INTERFACE UNIT
IDT82V2082
FEATURES:
•
•
•
•
•
•
•
-
Dual channel T1/E1/J1 long haul/short haul line interfaces
Supports HPS (Hitless Protection Switching) for 1+1 protection
without external relays
Receiver sensitivity exceeds -36 dB@772KHz and -43
dB@1024 KHz
Programmable T1/E1/J1 switchability allowing one bill of material for any line condition
Single 3.3 V power supply with 5 V tolerance on digital interfaces
Meets or exceeds specifications in
- ANSI T1.102, T1.403 and T1.408
- ITU I.431, G.703, G.736, G.775 and G.823
- ETSI 300-166, 300-233 and TBR12/13
- AT&T Pub 62411
Software programmable or hardware selectable on:
- Wave-shaping templates for short haul and long haul LBO (Line
Build Out)
- Line terminating impedance (T1:100 Ω, J1:110 Ω, E1:75 Ω/120
Ω)
- Adjustment of arbitrary pulse shape
- JA (Jitter Attenuator) position (receive path or transmit path)
- Single rail/dual rail system interfaces
- B8ZS/HDB3/AMI line encoding/decoding
•
•
•
•
•
•
•
•
Active edge of transmit clock (TCLK) and receive clock (RCLK)
Active level of transmit data (TDATA) and receive data (RDATA)
Receiver or transmitter power down
High impedance setting for line drivers
PRBS (Pseudo Random Bit Sequence) generation and detection
with 215-1 PRBS polynomials for E1
- QRSS (Quasi Random Sequence Signals) generation and detection with 220-1 QRSS polynomials for T1/J1
- 16-bit BPV (Bipolar Pulse Violation) /Excess Zero/PRBS or QRSS
error counter
- Analog loopback, Digital loopback, Remote loopback and Inband
loopback
Cable attenuation indication
Adaptive receive sensitivity
Non-intrusive monitoring per ITU G.772 specification
Short circuit protection and internal protection diode for line
drivers
LOS (Loss Of Signal) & AIS (Alarm Indication Signal) detection
JTAG interface
Supports serial control interface, Motorola and Intel Non-Multiplexed interfaces and hardware control mode
Package:
IDT82V2082: 80-pin TQFP
DESCRIPTION:
The IDT82V2082 can be configured as a dual channel T1, E1 or J1 Line
Interface Unit. In receive path, an Adaptive Equalizer is integrated to
remove the distortion introduced by the cable attenuation. The
IDT82V2082 also performs clock/data recovery, AMI/B8ZS/HDB3 line
decoding and detects and reports the LOS conditions. In transmit path,
there is an AMI/B8ZS/HDB3 encoder, Waveform Shaper and LBOs.
There is one Jitter Attenuator, which can be placed in either the receive
path or the transmit path. The Jitter Attenuator can also be disabled. The
IDT82V2082 supports both Single Rail and Dual Rail system interfaces.
To facilitate the network maintenance, a PRBS/QRSS generation/detec-
tion circuit is integrated in the chip, and different types of loopbacks can
be set according to the applications. Four different kinds of line terminating
impedance, 75 Ω, 100 Ω, 110 Ω and 120 Ω are selectable on a per channel basis. The chip also provides driver short-circuit protection and internal
protection diode and supports JTAG boundary scanning. The chip can be
controlled by either software or hardware.
The IDT82V2082 can be used in LAN, WAN, Routers, Wireless Base
Stations, IADs, IMAs, IMAPs, Gateways, Frame Relay Access Devices,
CSU/DSU equipment, etc.
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGES
July 2004
1
 2003 Integrated Device Technology, Inc. All rights reserved.
DSC-6229/5
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
FUNCTIONAL BLOCK DIAGRAM
LOSn
One of the Two Identical Channels
LOS/AIS
Detector
RCLKn
RDn/RDPn
CVn/RDNn
B8ZS/
HDB3/AMI
Decoder
PRBS Detector
IBLC Detector
TCLKn
TDn/TDPn
TDNn
Jitter
Attenuator
Remote
Loopback
B8ZS/
HDB3/AMI
Decoder
Data and
Clock
Recovery
Adaptive
Equalizer
Data
Slicer
Receiver
Internal
Termination
RRINGn
Analog
Loopback
Digital
Loopback
Jitter
Attenuator
RTIPn
Waveform
Shaper/LBO
TTIPn
Transmitter
Internal
Termination
Line
Driver
TRINGn
PRBS Generator
IBLC Generator
TAOS
Figure-1 Block Diagram
2
JTAG TAP
TDI
TDO
Pin Control
TRST
TCK
TMS
Register
Files
MODE[1:0]
TERMn
RXTXM[1:0]
PULSn[3:0]
EQn
PATTn[1:0]
JA[1:0]
MONTn
LPn[1:0]
THZ
RCLKE
RPDn
RST
Software Control Interface
INT
CS
SDO
SCLK
R/W/WR/SDI
RD/DS/SCLKE
A[5:0]
D[7:0]
MCLK
Clock
Generator
VDDIO
VDDD
VDDA
VDDT
VDDR
G.772
Monitor
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
TABLE OF CONTENTS
1
IDT82V2082 PIN CONFIGURATIONS .......................................................................................... 8
2
PIN DESCRIPTION ....................................................................................................................... 9
3
FUNCTIONAL DESCRIPTION .................................................................................................... 17
3.1
CONTROL MODE SELECTION ....................................................................................... 17
3.2
T1/E1/J1 MODE SELECTION .......................................................................................... 17
3.3
TRANSMIT PATH ............................................................................................................. 17
3.3.1 TRANSMIT PATH SYSTEM INTERFACE.............................................................. 17
3.3.2 ENCODER ............................................................................................................. 17
3.3.3 PULSE SHAPER .................................................................................................... 17
3.3.3.1 Preset Pulse Templates .......................................................................... 17
3.3.3.2 LBO (Line Build Out) ............................................................................... 18
3.3.3.3 User-Programmable Arbitrary Waveform ................................................ 18
3.3.4 TRANSMIT PATH LINE INTERFACE..................................................................... 22
3.3.5 TRANSMIT PATH POWER DOWN ........................................................................ 23
3.4
RECEIVE PATH ............................................................................................................... 23
3.4.1 RECEIVE INTERNAL TERMINATION.................................................................... 23
3.4.2 LINE MONITOR ...................................................................................................... 24
3.4.3 ADAPTIVE EQUALIZER......................................................................................... 25
3.4.4 RECEIVE SENSITIVITY ......................................................................................... 25
3.4.5 DATA SLICER ........................................................................................................ 25
3.4.6 CDR (Clock & Data Recovery)................................................................................ 25
3.4.7 DECODER .............................................................................................................. 25
3.4.8 RECEIVE PATH SYSTEM INTERFACE ................................................................ 25
3.4.9 RECEIVE PATH POWER DOWN........................................................................... 25
3.4.10 G.772 NON-INTRUSIVE MONITORING ................................................................ 26
3.5
JITTER ATTENUATOR .................................................................................................... 27
3.5.1 JITTER ATTENUATION FUNCTION DESCRIPTION ............................................ 27
3.5.2 JITTER ATTENUATOR PERFORMANCE ............................................................. 27
3.6
LOS AND AIS DETECTION ............................................................................................. 28
3.6.1 LOS DETECTION ................................................................................................... 28
3.6.2 AIS DETECTION .................................................................................................... 29
3.7
TRANSMIT AND DETECT INTERNAL PATTERNS ........................................................ 30
3.7.1 TRANSMIT ALL ONES ........................................................................................... 30
3.7.2 TRANSMIT ALL ZEROS......................................................................................... 30
3.7.3 PRBS/QRSS GENERATION AND DETECTION.................................................... 30
3.8
LOOPBACK ...................................................................................................................... 30
3.8.1 ANALOG LOOPBACK ............................................................................................ 30
3.8.2 DIGITAL LOOPBACK ............................................................................................. 30
3.8.3 REMOTE LOOPBACK............................................................................................ 30
3.8.4 INBAND LOOPBACK.............................................................................................. 32
3.8.4.1 Transmit Activate/Deactivate Loopback Code......................................... 32
3.8.4.2 Receive Activate/Deactivate Loopback Code.......................................... 32
3
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
INDUSTRIAL
TEMPERATURE RANGES
3.8.4.3 Automatic Remote Loopback .................................................................. 32
ERROR DETECTION/COUNTING AND INSERTION ...................................................... 33
3.9.1 DEFINITION OF LINE CODING ERROR ............................................................... 33
3.9.2 ERROR DETECTION AND COUNTING ................................................................ 33
3.9.3 BIPOLAR VIOLATION AND PRBS ERROR INSERTION ...................................... 34
LINE DRIVER FAILURE MONITORING ........................................................................... 34
MCLK AND TCLK ............................................................................................................. 35
3.11.1 MASTER CLOCK (MCLK) ...................................................................................... 35
3.11.2 TRANSMIT CLOCK (TCLK).................................................................................... 35
MICROCONTROLLER INTERFACES ............................................................................. 36
3.12.1 PARALLEL MICROCONTROLLER INTERFACE................................................... 36
3.12.2 SERIAL MICROCONTROLLER INTERFACE ........................................................ 36
INTERRUPT HANDLING .................................................................................................. 37
5V TOLERANT I/O PINS .................................................................................................. 37
RESET OPERATION ........................................................................................................ 37
POWER SUPPLY ............................................................................................................. 37
4
PROGRAMMING INFORMATION .............................................................................................. 38
4.1
REGISTER LIST AND MAP ............................................................................................. 38
4.2
REGISTER DESCRIPTION .............................................................................................. 40
4.2.1 GLOBAL REGISTERS............................................................................................ 40
4.2.2 TRANSMIT AND RECEIVE TERMINATION REGISTER ....................................... 41
4.2.3 JITTER ATTENUATION CONTROL REGISTER ................................................... 41
4.2.4 TRANSMIT PATH CONTROL REGISTERS........................................................... 42
4.2.5 RECEIVE PATH CONTROL REGISTERS ............................................................. 44
4.2.6 NETWORK DIAGNOSTICS CONTROL REGISTERS ........................................... 46
4.2.7 INTERRUPT CONTROL REGISTERS ................................................................... 49
4.2.8 LINE STATUS REGISTERS ................................................................................... 52
4.2.9 INTERRUPT STATUS REGISTERS ...................................................................... 54
4.2.10 COUNTER REGISTERS ........................................................................................ 55
5
HARDWARE CONTROL PIN SUMMARY .................................................................................. 56
6
IEEE STD 1149.1 JTAG TEST ACCESS PORT ........................................................................ 58
6.1
JTAG INSTRUCTIONS AND INSTRUCTION REGISTER ............................................... 59
6.2
JTAG DATA REGISTER ................................................................................................... 59
6.2.1 DEVICE IDENTIFICATION REGISTER (IDR) ........................................................ 59
6.2.2 BYPASS REGISTER (BR)...................................................................................... 59
6.2.3 BOUNDARY SCAN REGISTER (BSR) .................................................................. 59
6.2.4 TEST ACCESS PORT CONTROLLER .................................................................. 59
7
TEST SPECIFICATIONS ............................................................................................................ 62
8
MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS ......................................... 74
8.1
SERIAL INTERFACE TIMING .......................................................................................... 74
8.2
PARALLEL INTERFACE TIMING ..................................................................................... 75
4
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
LIST OF TABLES
Table-1
Table-2
Table-3
Table-4
Table-5
Table-6
Table-7
Table-8
Table-9
Table-10
Table-11
Table-12
Table-13
Table-14
Table-15
Table-16
Table-17
Table-18
Table-19
Table-20
Table-21
Table-22
Table-23
Table-24
Table-25
Table-26
Table-27
Table-28
Table-29
Table-30
Table-31
Table-32
Table-33
Table-34
Table-35
Table-36
Table-37
Table-38
Table-39
Table-40
Table-41
Table-42
Table-43
Table-44
Table-45
Table-46
Pin Description ................................................................................................................ 9
Transmit Waveform Value For E1 75 Ω ........................................................................ 19
Transmit Waveform Value For E1 120 Ω ...................................................................... 19
Transmit Waveform Value For T1 0~133 ft................................................................... 19
Transmit Waveform Value For T1 133~266 ft............................................................... 20
Transmit Waveform Value For T1 266~399 ft............................................................... 20
Transmit Waveform Value For T1 399~533 ft............................................................... 20
Transmit Waveform Value For T1 533~655 ft............................................................... 20
Transmit Waveform Value For J1 0~655 ft ................................................................... 21
Transmit Waveform Value For DS1 0 dB LBO.............................................................. 21
Transmit Waveform Value For DS1 -7.5 dB LBO ......................................................... 21
Transmit Waveform Value For DS1 -15.0 dB LBO ....................................................... 21
Transmit Waveform Value For DS1 -22.5 dB LBO ....................................................... 22
Impedance Matching for Transmitter ............................................................................ 22
Impedance Matching for Receiver ................................................................................ 23
Criteria of Starting Speed Adjustment........................................................................... 27
LOS Declare and Clear Criteria for Short Haul Mode ................................................... 28
LOS Declare and Clear Criteria for Long Haul Mode.................................................... 29
AIS Condition ................................................................................................................ 29
Criteria for Setting/Clearing the PRBS_S Bit ................................................................ 30
EXZ Definition ............................................................................................................... 33
Interrupt Event............................................................................................................... 37
Global Register List and Map........................................................................................ 38
Per Channel Register List and Map .............................................................................. 39
ID: Device Revision Register ........................................................................................ 40
RST: Reset Register ..................................................................................................... 40
GCF: Global Configuration Register ............................................................................. 40
INTCH: Interrupt Channel Indication Register............................................................... 40
TERM: Transmit and Receive Termination Configuration Register .............................. 41
JACF: Jitter Attenuation Configuration Register ........................................................... 41
TCF0: Transmitter Configuration Register 0 ................................................................. 42
TCF1: Transmitter Configuration Register 1 ................................................................. 42
TCF2: Transmitter Configuration Register 2 ................................................................. 43
TCF3: Transmitter Configuration Register 3 ................................................................. 43
TCF4: Transmitter Configuration Register 4 ................................................................. 43
RCF0: Receiver Configuration Register 0..................................................................... 44
RCF1: Receiver Configuration Register 1..................................................................... 45
RCF2: Receiver Configuration Register 2..................................................................... 46
MAINT0: Maintenance Function Control Register 0...................................................... 46
MAINT1: Maintenance Function Control Register 1...................................................... 47
MAINT2: Maintenance Function Control Register 2...................................................... 47
MAINT3: Maintenance Function Control Register 3...................................................... 47
MAINT4: Maintenance Function Control Register 4...................................................... 48
MAINT5: Maintenance Function Control Register 5...................................................... 48
MAINT6: Maintenance Function Control Register 6...................................................... 48
INTM0: Interrupt Mask Register 0 ................................................................................. 49
5
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-47
Table-48
Table-49
Table-50
Table-51
Table-52
Table-53
Table-54
Table-55
Table-56
Table-57
Table-58
Table-59
Table-60
Table-61
Table-62
Table-63
Table-64
Table-65
Table-66
Table-67
Table-68
Table-69
Table-70
Table-71
Table-72
Table-73
Table-74
Table-75
INDUSTRIAL
TEMPERATURE RANGES
INTM1: Interrupt Masked Register 1 .............................................................................
INTES: Interrupt Trigger Edge Select Register .............................................................
STAT0: Line Status Register 0 (real time status monitor).............................................
STAT1: Line Status Register 1 (real time status monitor).............................................
INTS0: Interrupt Status Register 0 ................................................................................
INTS1: Interrupt Status Register 1 ................................................................................
CNT0: Error Counter L-byte Register 0.........................................................................
CNT1: Error Counter H-byte Register 1 ........................................................................
Hardware Control Pin Summary ...................................................................................
Instruction Register Description ....................................................................................
Device Identification Register Description.....................................................................
TAP Controller State Description ..................................................................................
Absolute Maximum Rating ............................................................................................
Recommended Operation Conditions ...........................................................................
Power Consumption......................................................................................................
DC Characteristics ........................................................................................................
E1 Receiver Electrical Characteristics ..........................................................................
T1/J1 Receiver Electrical Characteristics......................................................................
E1 Transmitter Electrical Characteristics ......................................................................
T1/J1 Transmitter Electrical Characteristics..................................................................
Transmitter and Receiver Timing Characteristics .........................................................
Jitter Tolerance .............................................................................................................
Jitter Attenuator Characteristics ....................................................................................
JTAG Timing Characteristics ........................................................................................
Serial Interface Timing Characteristics .........................................................................
Non-Multiplexed Motorola Read Timing Characteristics ...............................................
Non-Multiplexed Motorola Write Timing Characteristics ...............................................
Non-Multiplexed Intel Read Timing Characteristics ......................................................
Non-Multiplexed Intel Write Timing Characteristics ......................................................
6
50
51
52
53
54
55
55
55
56
59
59
60
62
62
63
63
64
65
66
67
68
69
71
73
74
75
76
77
78
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
LIST OF FIGURES
Figure-1
Figure-2
Figure-3
Figure-4
Figure-5
Figure-6
Figure-7
Figure-8
Figure-9
Figure-10
Figure-11
Figure-12
Figure-13
Figure-14
Figure-15
Figure-16
Figure-17
Figure-18
Figure-19
Figure-20
Figure-21
Figure-22
Figure-23
Figure-24
Figure-25
Figure-26
Figure-27
Figure-28
Figure-29
Figure-30
Figure-31
Figure-32
Figure-33
Figure-34
Figure-35
Figure-36
Block Diagram ................................................................................................................. 2
IDT82V2082 TQFP80 Package Pin Assignment ............................................................ 8
E1 Waveform Template Diagram .................................................................................. 17
E1 Pulse Template Test Circuit ..................................................................................... 18
DSX-1 Waveform Template .......................................................................................... 18
T1 Pulse Template Test Circuit ..................................................................................... 18
Receive Path Function Block Diagram .......................................................................... 23
Transmit/Receive Line Circuit ....................................................................................... 24
Monitoring Receive Line in Another Chip ...................................................................... 24
Monitor Transmit Line in Another Chip .......................................................................... 24
G.772 Monitoring Diagram ............................................................................................ 26
Jitter Attenuator ............................................................................................................. 27
LOS Declare and Clear ................................................................................................. 28
Analog Loopback .......................................................................................................... 31
Digital Loopback ............................................................................................................ 31
Remote Loopback ......................................................................................................... 31
Auto Report Mode ......................................................................................................... 33
Manual Report Mode ..................................................................................................... 34
TCLK Operation Flowchart ............................................................................................ 35
Serial Microcontroller Interface Function Timing ........................................................... 36
JTAG Architecture ......................................................................................................... 58
JTAG State Diagram ..................................................................................................... 61
Transmit System Interface Timing ................................................................................ 69
Receive System Interface Timing ................................................................................. 69
E1 Jitter Tolerance Performance .................................................................................. 70
T1/J1 Jitter Tolerance Performance .............................................................................. 70
E1 Jitter Transfer Performance ..................................................................................... 72
T1/J1 Jitter Transfer Performance ................................................................................ 72
JTAG Interface Timing .................................................................................................. 73
Serial Interface Write Timing ......................................................................................... 74
Serial Interface Read Timing with SCLKE=1 ................................................................ 74
Serial Interface Read Timing with SCLKE=0 ................................................................ 74
Non-Multiplexed Motorola Read Timing ........................................................................ 75
Non-Multiplexed Motorola Write Timing ........................................................................ 76
Non-Multiplexed Intel Read Timing ............................................................................... 77
Non-Multiplexed Intel Write Timing ............................................................................... 78
7
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INT / LP10
D1 / PULS21
48
CS / LP11
D2 / PULS22
49
41
D3 / PULS23
50
SDO / LP20
D4 / PULS10
51
42
D5 / PULS11
52
R/W / WR / SDI / LP21
D6 / PULS12
53
43
D7 / PULS13
54
DS / RD / SCLKE / PATT10
A0 / PATT20
44
A1 / PATT21
55
SCLK / PATT11
A2 / RPD1
57
56
45
A3 / EQ1
58
D0 / PULS20
A4 / RPD2
59
47
46
A5 / EQ2
60
IDT82V2082 PIN CONFIGURATIONS
VDDT1
61
40
VDDIO
TRING1
62
39
GNDIO
TTIP1
63
38
TCLK1
GNDT1
64
37
TDP1 / TD1
GNDR1
65
36
TDN1
RRING1
66
35
RCLK1
RTIP1
67
34
RDP1 / RD1
VDDR1
68
33
RDN1 / CV1
VDDA
69
32
LOS1
IC
70
31
VDDD
REF
71
30
MCLK
GNDA
72
29
GNDD
VDDR2
73
28
LOS2
RTIP2
74
27
RDN2 / CV2
RRING2
75
26
RDP2 / RD2
GNDR2
76
25
RCLK2
GNDT2
77
24
TDN2
TTIP2
78
23
TDP2 / TD2
TRING2
79
22
TCLK2
VDDT2
80
21
RST
12
13
14
15
16
17
18
19
20
TERM1
RXTXM1
RXTXM0
JA1
JA0
MONT2
MONT1
THZ
8
VDDIO
GNDIO
TERM2
7
IC
RCLKE
6
TDI
11
5
TDO
9
4
TCK
10
3
MODE0
2
MODE1
1
TMS
IDT82V2082
TRST
1
Figure-2 IDT82V2082 TQFP80 Package Pin Assignment
8
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
2
PIN DESCRIPTION
Table-1 Pin Description
Name
Type
Pin No.
TTIP1
TTIP2
Analog
Output
63
78
TRING1
TRING2
RTIP1
RTIP2
62
79
Analog
Input
RRING1
RRING2
TD1/TDP1
TD2/TDP2
67
74
Description
1
TTIPn /TRINGn: Transmit Bipolar Tip/Ring for Channel 1~2
These pins are the differential line driver outputs and can be set to high impedance state globally or individually. A logic high
on THZ pin turns all these pins into high impedance state. When THZ bit (TCF1, 03H...)2 is set to ‘1’, the TTIPn/TRINGn in
the corresponding channel is set to high impedance state.
In summary, these pins will become high impedance in the following conditions:
•
THZ pin is high: all TTIPn/TRINGn enter high impedance;
•
THZn bit is set to 1: the corresponding TTIPn/TRINGn become high impedance;
•
Loss of MCLK: all TTIPn/TRINGn pins become high impedance;·
•
Loss of TCLKn: the corresponding TTIPn/TRINGn become HZ (exceptions: Remote Loopback; Transmit internal pattern by MCLK);
•
Transmitter path power down: the corresponding TTIPn/TRINGn become high impedance;
•
After software reset; pin reset and power on: all TTIPn/TRINGn enter high impedance.
RTIPn/RRINGn: Receive Bipolar Tip/Ring for Channel 1~2
These signals are the differential receiver inputs.
66
75
I
TDN1
TDN2
37
23
36
24
TDn: Transmit Data for Channel 1~2
When the device is in single rail mode, the NRZ data to be transmitted is input on this pin. Data on TDn pin is sampled into
the device on the active edge of TCLKn and is encoded by AMI, HDB3 or B8ZS line code rules before being transmitted. In
this mode, TDNn should be connected to ground.
TDPn/TDNn: Positive/Negative Transmit Data
When the device is in dual rail mode, the NRZ data to be transmitted for positive/negative pulse is input on these pins. Data
on TDPn/TDNn pin is sampled into the device on the active edge of TCLKn. The active polarity is also selectable. Refer to
TRANSMIT PATH SYSTEM INTERFACE for details.The line code in dual rail mode is as follows:
TCLK1
TCLK2
I
38
22
TDPn
TDNn
Output Pulse
0
0
Space
0
1
Positive Pulse
1
0
Negative Pulse
1
1
Space
TCLKn: Transmit Clock for Channel 1~2
This pin inputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode transmit clock. The transmit data at TDn/TDPn or TDNn
is sampled into the device on the active edge of TCLKn. If TCLKn is missing3 and the TCLKn missing interrupt is not masked,
an interrupt will be generated.
Notes:
1. The footprint ‘n’ (n = 1~2) represents one of the two channels.
2. The name and address of the registers that contain the preceding bit. Only the address of channel 1 register is listed, the rest addresses are represented by ‘...’. Users can find
these omitted addresses in the Register Description section.
3. TCLKn missing: the state of TCLKn continues to be high level or low level over 70 MCLK cycles.
9
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
RD1/RDP1
RD2/RDP2
O
34
26
RDn: Receive Data output for Channel 1~2
In single rail mode, this pin outputs NRZ data. The data is decoded according to AMI, HDB3 or B8ZS line code rules.
33
27
CVn: Code Violation indication
In single rail mode, the BPV/CV errors in received data stream will be reported by driving the CVn pin to high level for a full
clock cycle. B8ZS/HDB3 line code violation can be indicated if the B8ZS/HDB3 decoder is enabled. When AMI decoder is
selected, bipolar violation will be indicated.
In hardware control mode, the EXZ, BPV/CV errors in received data stream are always monitored by the CVn pin if single rail
mode is chosen.
CV1/RDN1
CV2/RDN2
Description
RDPn/RDNn: Positive/Negative Receive Data output for Channel 1~2
In dual rail mode, these pins output the re-timed NRZ data when CDR is enabled, or directly outputs the raw RZ slicer data
if CDR is bypassed.
Active edge and level select:
Data on RDPn/RDNn or RDn is clocked with either the rising or the falling edge of RCLKn. The active polarity is also selectable. Refer to RECEIVE PATH SYSTEM INTERFACE for details.
RCLK1
RCLK2
O
35
25
RCLKn: Receive Clock output for Channel 1~2
This pin outputs 1.544 MHz for T1/J1 mode or 2.048 MHz for E1 mode receive clock. Under LOS conditions with AIS enabled
(bit AISE=1), RCLKn is derived from MCLK.
In clock recovery mode, this signal provides the clock recovered from the RTIPn/RRINGn signal. The receive data (RDn in
single rail mode or RDPn and RDNn in dual rail mode) is clocked out of the device on the active edge of RCLKn.
If clock recovery is bypassed, RCLKn is the exclusive OR (XOR) output of the dual rail slicer data RDPn and RDNn. This signal
can be used in applications with external clock recovery circuitry.
MCLK
I
30
MCLK: Master Clock input
A built-in clock system that accepts selectable 2.048MHz reference for E1 operating mode and 1.544MHz reference for T1/
J1 operating mode. This reference clock is used to generate several internal reference signals:
•
Timing reference for the integrated clock recovery unit.
•
Timing reference for the integrated digital jitter attenuator.
•
Timing reference for microcontroller interface.
•
Generation of RCLKn signal during a loss of signal condition.
•
Reference clock to transmit All Ones, all zeros, PRBS/QRSS pattern as well as activate or deactivate Inband Loopback code if MCLK is selected as the reference clock. Note that for ATAO and AIS, MCLK is always used as the reference clock.
•
Reference clock during Transmit All Ones (TAO) condition or sending PRBS/QRSS in hardware control mode.
The loss of MCLK will turn TTIP/TRING into high impedance status.
LOS1
LOS2
O
32
28
LOSn: Loss of Signal Output for Channel 1~2
These pins are used to indicate the loss of received signals. When LOSn pin becomes high, it indicates the loss of received
signal in channel n. The LOS pin will become low automatically when valid received signal is detected again. The criteria of
loss of signal are described in 3.6 LOS AND AIS DETECTION.
REF
I
71
REF: reference resister
An external resistor (3kΩ, 1%) is used to connect this pin to ground to provide a standard reference current for internal circuit.
10
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
MODE1
MODE0
I
9
10
Description
MODE[1:0]: operation mode of control interface select
The level on this pin determines which control mode is used to control the device as follows:
MODE[1:0]
•
•
•
Control Interface mode
00
Hardware interface
01
Serial Microcontroller Interface
10
Motorola non-multiplexed
11
Intel non-multiplexed
The serial microcontroller interface consists of CS, SCLK, SCLKE, SDI, SDO and INT pins. SCLKE is used for the
selection of the active edge of SCLK.
The parallel non-multiplexed microcontroller interface consists of CS, A[5:0], D[7:0], DS/RD, R/W/WR and INT pins.
(Refer to 3.12 MICROCONTROLLER INTERFACES for details)
Hardware interface consists of PULSn[3:0], THZ, RCLKE, LPn[1:0], PATTn[1:0], JA[1:0], MONTn, TERMn, EQn,
RPDn, MODE[1:0] and RXTXM[1:0] (n=1, 2).
RCLKE
I
11
RCLKE: the active edge of RCLKn select
In hardware control mode, this pin selects the active edge of RCLKn
•
L= update RDPn/RDNn on the rising edge of RCLKn
•
H= update RDPn/RDNn on the falling edge of RCLKn
In software control mode, this pin should be connected to GNDIO.
RXTXM1
RXTXM0
I
14
15
RXTXM[1:0]: Receive and transmit path operation mode select
In hardware control mode, these pins are used to select the single rail or dual rail operation modes as well as AMI or HDB3/
B8ZS line coding:
•
00= single rail with HDB3/B8ZS coding
•
01= single rail with AMI coding
•
10= dual rail interface with CDR enabled
•
11= slicer mode (dual rail interface with CDR disabled)
In software control mode, these pins should be connected to ground.
CS
I
42
CS: Chip Select
In serial or parallel microcontroller interface mode, this is the active low enable signal. A low level on this pin enables serial
or parallel microcontroller interface.
LP11
INT
LP11/LP10: Loopback mode select for channel 1
When the chip is configured by hardware, this pin is used to select loopback operation modes for channel 1(Inband Loopback
is not provided in hardware control mode)
•
00= no loopback
•
01= analog loopback
•
10= digital loopback
•
11= remote loopback
O
41
INT: Interrupt Request
In software control mode, this pin outputs the general interrupt request for all interrupt sources. If INTM_GLB bit (GCF, 20H)
is set to ‘1’, all the interrupt sources will be masked. These interrupt sources can be masked individually via registers (INTM0,
13H...) and (INTM1, 14H...). The interrupt status is reported via the registers (INTCH, 21H), (INTS0, 18H...) and (INTS1,
19H...).
Output characteristics of this pin can be defined to be push-pull (active high or active low) or open-drain (active low) by setting
bits INT_PIN[1:0] (GCF, 20H)
LP10
I
LP11/LP10: Loopback mode select for channel 1
See above LP11.
11
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
SCLK
I
46
SCLK: Shift Clock
In serial microcontroller interface mode, this signal is the shift clock for the serial interface. Configuration data on SDI pin is
sampled on the rising edge of SCLK. Configuration and status data on SDO pin is clocked out of the device on the rising edge
of SCLK if SCLKE pin is low, or on the falling edge of SCLK if SCLKE pin is high.
In parallel non-multiplexed interface mode, this pin should be connected to ground.
PATT11
SCLKE
PATT11/PATT10: Transmit pattern select for channel 1
In hardware control mode, this pin selects the transmit pattern
•
00 = normal
•
01= All Ones
•
10= PRBS
•
11= transmitter power down
I
45
SCLKE: Serial Clock Edge Select
In serial microcontroller interface mode, this signal selects the active edge of SCLK for outputting SDO. The output data is
valid after some delay from the active clock edge. It can be sampled on the opposite edge of the clock. The active clock edge
which clocks the data out of the device is selected as shown below:
SCLKE
SCLK
Low
Rising edge is the active edge.
High
Falling edge is the active edge.
DS
DS: Data Strobe
In Motorola parallel non-multiplexed interface mode, this signal is the data strobe of the parallel interface. In a write operation
(R/W = 0), the data on D[7:0] is sampled into the device. In a read operation (R/W = 1), the data is driven to D[7:0] by the
device.
RD
RD: Read Strobe
In Intel parallel non-Multiplexed interface mode, the data is driven to D[7:0] by the device during low level of RD in a read operation.
PATT11/PATT10: Transmit pattern select for channel 1
See above PATT11.
PATT10
SDI
I
44
SDI: Serial Data Input
In serial microcontroller interface mode, this signal is the input data to the serial interface. Configuration data at SDI pin is sampled by the device on the rising edge of SCLK.
R/W
R/W: Read/Write Select
In Motorola parallel non-multiplexed interface mode, this pin is low for write operation and high for read operation.
WR
WR: Write Strobe
In Intel parallel non-multiplexed interface mode, this pin is asserted low by the microcontroller to initiate a write cycle. The data
on D[7:0] is sampled into the device in a write operation.
LP21
LP21/LP20: loopback mode select for channel 2
When the chip is configured by hardware, this pin is used to select loopback operation modes for channel 2(Inband Loopback
is not provided in hardware control mode)
•
00= no loopback
•
01= analog loopback
•
10= digital loopback
•
11= remote loopback
12
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
SDO
O
43
SDO: Serial Data Output
In serial microcontroller interface mode, this signal is the output data of the serial interface. Configuration or Status data at
SDO pin is clocked out of the device on the rising edge of SCLK if SCLKE pin is low, or on the falling edge of SCLK if SCLKE
pin is high.
In parallel non-multiplexed interface mode, this pin should be left open.
LP20
I
D7
I/O
PULS13
I
D6
I/O
PULS12
I
D5
I/O
PULS11
I
D4
I/O
PULS10
I
D3
I/O
PULS23
I
D2
I/O
PULS22
I
D1
I/O
PULS21
I
D0
I/O
PULS20
I
LP21/LP20: loopback mode select for channel 2
See above LP21.
54
D7: Data Bus bit7
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
PULS1[3:0]: these pins are used to select the following functions for channel 1 in hardware control mode:
•
T1/E1/J1 mode
•
Transmit pulse template
•
Internal termination impedance (75Ω/120Ω/100Ω/110Ω)
Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
Note that PULS13 to PULS10 determine the T1/E1/J1 mode of common block.
53
D6: Data Bus bit6
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
52
D5: Data Bus bit5
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
See above.
See above.
51
D4: Data Bus bit4
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
50
D3: Data Bus bit3
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
See above.
PULS2[3:0]: these pins are used to select the following functions for channel 2 in hardware control mode:·
•
T1/E1/J1 mode
•
Transmit pulse template
•
Internal termination impedance (75Ω/120Ω/100Ω/110Ω)
Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
49
D2: Data Bus bit2
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
48
D1: Data Bus bit1
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
See above
See above
47
D0: Data Bus bit0
In Intel/Motorola non-multiplexed interface mode, this signal is the bi-directional data bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground through a 10 kΩ resistor.
See above.
13
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
A5
I
60
EQ2
A4
I
59
I
58
I
57
A2: Address Bus bit2
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
RPD1: Power down control for receiver1 in hardware control mode
0= receiver 1 normal operation
1= receiver 1 power down
I
56
PATT21
A0
A3: Address Bus bit3
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
EQ1: Equalizer on/off for receiver1 in hardware control mode
0= short haul (10dB)
1= long haul (36dB for T1/J1, 43 dB for E1)
RPD1
A1
A4: Address Bus bit4
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
RPD2: Power down control for receiver2 in hardware control mode
0= receiver 2 normal operation
1= receiver 2 power down
EQ1
A2
A5: Address Bus bit5
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
EQ2: Equalizer on/off for receiver2 in hardware control mode
0= short haul (10dB)
1= long haul (36dB for T1/J1, 43 dB for E1)
RPD2
A3
Description
A1: Address Bus bit1
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
PATT21/PATT20: Transmit pattern select for channel 2
In hardware control mode, this pin selects the transmit pattern
00 = normal
01= All Ones
10= PRBS
11= transmitter power down
I
55
PATT20
A0: Address Bus bit 0
In Intel/Motorola non-multiplexed interface mode, this signal is the address bus of the microcontroller interface.
In serial microcontroller interface mode, this pin should be connected to ground.
See above
TERM1
TERM2
I
13
12
TERMn: Selects internal or external impedance matching for channel 1 and channel 2 in hardware control mode
0 = ternary interface with internal impedance matching network
1 = ternary interface with external impedance matching network in E1 mode; ternary interface with external impedance matching network for receiver and ternary interface with internal impedance matching network for transmitter in T1/J1 mode.
(This applies to ZB die revision only.)
In software control mode, this pin should be connected to ground.
JA1
I
16
JA[1:0]: Jitter attenuation position, bandwidth and the depth of FIFO select for channel 1 and channel 2 (only used
in hardware control mode)
•
00 = JA is disabled
•
01= JA in receiver, broad bandwidth, FIFO=64 bits
•
10 = JA in receiver, narrow bandwidth, FIFO=128 bits
•
11= JA in transmitter, narrow bandwidth, FIFO=128 bits
In software control mode, this pin should be connected to ground.
JA0
I
17
See above.
14
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
MONT2
I
18
MONT2: Receive Monitor gain select for channel 2
In hardware control mode with ternary interface, this pin selects the receive monitor gain of receiver:
0= 0dB
1= 26dB
In software control mode, this pin should be connected to ground.
MONT1
I
19
MONT1: Receive Monitor gain select for channel 1
In hardware control mode with ternary interface, this pin selects the receive monitor gain of receiver:
0= 0dB
1= 26dB
In software control mode, this pin should be connected to ground.
RST
I
21
RST: Hardware Reset
The chip is forced to reset state if a low signal is input on this pin for more than 100ns.
THZ
I
20
THZ: Transmitter Driver High Impedance Enable
This signal enables or disables all transmitter drivers on a global basis. A low level on this pin enables the driver while a high
level on this pin places all drivers in high impedance state. Note that the functionality of the internal circuits is not affected by
this signal.
TRST
I
Pullup
1
TRST: JTAG Test Port Reset
This is the active low asynchronous reset to the JTAG Test Port. This pin has an internal pull-up resistor. To ensure deterministic operation of the test logic, TMS should be held high while the signal applied to TRST changes from low to high.
JTAG Signals
For normal signal processing, this pin should be connected to ground.
TMS
I
Pullup
2
TMS: JTAG Test Mode Select
This pin is used to control the test logic state machine and is sampled on the rising edge of TCK. TMS has an internal pullup resistor.
TCK
I
3
TCK: JTAG Test Clock
This is the input clock for JTAG. The data on TDI and TMS are clocked into the device on the rising edge of TCK while the
data on TDO is clocked out of the device on the falling edge of TCK. When TCK is idle at low state, all the stored-state devices
contained in the test logic will retain their state indefinitely.
TDO
O
4
TDO: JTAG Test Data Output
This output pin is high impedance normally and is used for reading all the serial configuration and test data from the test logic.
The data on TDO is clocked out of the device on the falling edge of TCK.
TDI
I
Pullup
5
TDI: JTAG Test Data Input
This pin is used for loading instructions and data into the test logic and has an internal pull-up resistor. The data on TDI is
clocked into the device on the rising edge of TCK.
VDDIO
-
7,40
3.3 V I/O power supply
GNDIO
-
8,39
I/O ground
VDDT1
VDDT2
-
61
80
3.3 V power supply for transmitter driver
GNDT1
GNDT2
-
64
77
Analog ground for transmitter driver
VDDR1
VDDR2
-
68
73
Power supply for receive analog circuit
GNDR1
GNDR2
-
65
76
Analog ground for receive analog circuit
VDDD
-
31
3.3V digital core power supply
GNDD
-
29
Digital core ground
VDDA
-
69
Analog core circuit power supply
GNDA
-
72
Analog core circuit ground
Power Supplies and Grounds
15
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-1 Pin Description (Continued)
Name
Type
Pin No.
Description
IC
-
70
IC: Internal Connection
Internal Use. This pin should be left open when in normal operation.
IC
-
6
IC: Internal Connection
Internal Use. This pin should be connected to ground when in normal operation.
Others
16
INDUSTRIAL
TEMPERATURE RANGES
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3
FUNCTIONAL DESCRIPTION
3.3.2
3.1
CONTROL MODE SELECTION
In Single Rail mode, when T1/J1 mode is selected, the Encoder can be
selected to be a B8ZS encoder or an AMI encoder by setting T_MD[0] bit
(TCF0, 04H...).
The IDT82V2082 can be configured by software or by hardware. The
software control mode supports Serial Control Interface, Motorola non-Multiplexed Control Interface and Intel non-Multiplexed Control Interface. The
Control mode is selected by MODE1 and MODE0 pins as follows:
In Single Rail mode, when E1 mode is selected, the Encoder can be configured to be a HDB3 encoder or an AMI encoder by setting T_MD[0] bit
(TCF0, 04H...).
In both T1/J1 mode and E1 mode, when Dual Rail mode is selected (bit
T_MD[1] is ‘1’), the Encoder is by-passed. In Dual Rail mode, a logic ‘1’ on
the TDPn pin and a logic ‘0’ on the TDNn pin results in a negative pulse on
the TTIPn/TRINGn; a logic ‘0’ on TDPn pin and a logic ‘1’ on TDNn pin
results in a positive pulse on the TTIPn/TRINGn. If both TDPn and TDNn
are high or low, the TTIPn/TRINGn outputs a space (Refer to TDn/TDPn,
TDNn Pin Description).
Control Interface mode
•
•
•
00
Hardware interface
01
Serial Microcontroller Interface.
10
Parallel -non-Multiplexed -Motorola Interface
11
Parallel -non-Multiplexed -Intel Interface
The serial microcontroller Interface consists of CS, SCLK, SCLKE,
SDI, SDO and INT pins. SCLKE is used for the selection of active
edge of SCLK.
The parallel non-Multiplexed microcontroller Interface consists of
CS, A[5:0], D[7:0], DS/RD, R/W/WR and INT pins.
Hardware interface consists of PULSn[3:0], THZ, RCLKE, LPn[1:0],
PATTn[1:0], JA[1:0], MONTn, TERMn, EQn, RPDn, MODE[1:0] and
RXTXM[1:0] (n=1, 2). Refer to 5 HARDWARE CONTROL PIN
SUMMARY for details about hardware control.
3.2
In hardware control mode, the operation mode of receive and transmit
path can be selected by setting RXTXM1 and RXTXM0 pins on a global
basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.3.3
T1/E1/J1 MODE SELECTION
In software control mode, the pulse shape can be selected by setting
the related registers.
In hardware control mode, the pulse shape can be selected by setting
PULSn[3:0] pins on a per channel basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
When the chip is configured by hardware, T1/E1/J1 mode is selected
by PULSn[3:0] pins on a per channel basis. These pins also determine
transmit pulse template and internal termination impedance. Refer to 5
HARDWARE CONTROL PIN SUMMARY for details.
3.3.3.1 Preset Pulse Templates
For E1 applications, the pulse shape is shown in Figure-3 according to
the G.703 and the measuring diagram is shown in Figure-4. In internal
impedance matching mode, if the cable impedance is 75 Ω, the PULS[3:0]
bits (TCF1, 05H...) should be set to ‘0000’; if the cable impedance is 120
Ω, the PULS[3:0] bits (TCF1, 05H...) should be set to ‘0001’. In external
impedance matching mode, for both E1/75 Ω and E1/120 Ω cable impedance, PULS[3:0] should be set to ‘0001’.
TRANSMIT PATH
The transmit path of each channel of IDT82V2082 consists of an
Encoder, an optional Jitter Attenuator, a Waveform Shaper, a set of LBOs,
a Line Driver and a Programmable Transmit Termination.
3.3.1
PULSE SHAPER
The IDT82V2082 provides three ways of manipulating the pulse shape
before sending it. The first is to use preset pulse templates for short haul
application, the second is to use LBO (Line Build Out) for long haul application and the other way is to use user-programmable arbitrary waveform
template.
When the chip is configured by software, T1/E1/J1 mode is selected by
the T1E1 bit (GCF, 20H). In E1 application, the T1E1 bit (GCF, 20H) should
be set to ‘0’. In T1/J1 application, the T1E1 bit should be set to ‘1’.
3.3
ENCODER
TRANSMIT PATH SYSTEM INTERFACE
The transmit path system interface consists of TCLKn pin, TDn/TDPn
pin and TDNn pin. In E1 mode, TCLKn is a 2.048 MHz clock. In T1/J1 mode,
TCLKn is a 1.544 MHz clock. If TCLKn is missing for more than 70 MCLK
cycles, an interrupt will be generated if it is not masked.
1 .2 0
1 .0 0
0 .8 0
Normalized Amplitude
Transmit data is sampled on the TDn/TDPn and TDNn pins by the active
edge of TCLKn. The active edge of TCLKn can be selected by the
TCLK_SEL bit (TCF0, 04H...). And the active level of the data on TDn/TDPn
and TDNn can be selected by the TD_INV bit (TCF0, 04H...). In hardware
control mode, the falling edge of TCLKn and the active high of transmit data
are always used.
0 .6 0
0 .4 0
0 .2 0
0 .0 0
The transmit data from the system side can be provided in two different
ways: Single Rail and Dual Rail. In Single Rail mode, only TDn pin is used
for transmitting data and the T_MD[1] bit (TCF0, 04H...) should be set to
‘0’. In Dual Rail Mode, both TDPn pin and TDNn pin are used for transmitting
data, the T_MD[1] bit (TCF0, 04H...) should be set to ‘1’.
- 0 .2 0
-0 .6
- 0 .4
- 0 .2
0
0 .2
0 .4
0 .6
T im e in U n it In te rv a ls
Figure-3 E1 Waveform Template Diagram
17
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
3.3.3.3 User-Programmable Arbitrary Waveform
When the PULS[3:0] bits are set to ‘11xx’, user-programmable arbitrary
waveform generator mode can be used in the corresponding channel. This
allows the transmitter performance to be tuned for a wide variety of line condition or special application.
TTIPn
IDT82V2082
RLOAD
VOUT
TRINGn
Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by
UI[1:0] bits (TCF3, 07H...) and each UI is divided into 16 sub-phases,
addressed by the SAMP[3:0] bits (TCF3, 07H...). The pulse amplitude of
each phase is represented by a binary byte, within the range from +63 to 63, stored in WDAT[6:0] bits (TCF4, 08H...) in signed magnitude form. The
most positive number +63 (D) represents the maximum positive amplitude
of the transmit pulse while the most negative number -63 (D) represents the
maximum negative amplitude of the transmit pulse. Therefore, up to 64
bytes are used. For each channel, a 64 bytes RAM is available.
There are twelve standard templates which are stored in an on-chip ROM.
User can select one of them as reference and make some changes to get
the desired waveform.
Note: 1. For RLOAD = 75 Ω (nom), Vout (Peak)=2.37V (nom)
2. For RLOAD =120 Ω (nom), Vout (Peak)=3.00V (nom)
Figure-4 E1 Pulse Template Test Circuit
For T1 applications, the pulse shape is shown in Figure-5 according to
the T1.102 and the measuring diagram is shown in Figure-6. This also
meets the requirement of G.703, 2001. The cable length is divided into five
grades, and there are five pulse templates used for each of the cable length.
The pulse template is selected by PULS[3:0] bits (TCF1, 05H...).
User can change the wave shape and the amplitude to get the desired
pulse shape. In order to do this, firstly, users can choose a set of waveform
value from the following twelve tables, which is the most similar to the
desired pulse shape. Table-2, Table-3, Table-4, Table-5, Table-6, Table-7,
Table-8, Table-9, Table-10, Table-11, Table-12 and Table-13 list the sample
data and scaling data of each of the twelve templates. Then modify the corresponding sample data to get the desired transmit pulse shape.
1.2
1
Normalized Amplitude
0.8
0.6
0.4
Secondly, through the value of SCAL[5:0] bits increased or decreased
by 1, the pulse amplitude can be scaled up or down at the percentage ratio
against the standard pulse amplitude if needed. For different pulse shapes,
the value of SCAL[5:0] bits and the scaling percentage ratio are different.
The following twelve tables list these values.
0.2
0
-0.2
-0.4
Do the followings step by step, the desired waveform can be programmed, based on the selected waveform template:
(1).Select the UI by UI[1:0] bits (TCF3, 07H...)
(2).Specify the sample address in the selected UI by SAMP [3:0] bits
(TCF3, 07H...)
(3).Write sample data to WDAT[6:0] bits (TCF4, 08H...). It contains the
data to be stored in the RAM, addressed by the selected UI and the
corresponding sample address.
(4).Set the RW bit (TCF3, 07H...) to ‘0’ to implement writing data to RAM,
or to ‘1’ to implement read data from RAM
(5).Implement the Read from RAM/Write to RAM by setting the DONE
bit (TCF3, 07H...)
-0.6
0
250
500
750
1000
1250
Time (ns)
Figure-5 DSX-1 Waveform Template
TTIPn
Cable
IDT82V2082
RLOAD VOUT
TRINGn
Note: RLOAD = 100 Ω ± 5%
Repeat the above steps until all the sample data are written to or read
from the internal RAM.
(6).Write the scaling data to SCAL[5:0] bits (TCF2, 06H...) to scale the
amplitude of the waveform based on the selected standard pulse
amplitude
Figure-6 T1 Pulse Template Test Circuit
For J1 applications, the PULS[3:0] (TCF1, 05H...) should be set to
‘0111’. Table-14 lists these values.
When more than one UI is used to compose the pulse template, the overlap of two consecutive pulses could make the pulse amplitude overflow
(exceed the maximum limitation) if the pulse amplitude is not set properly.
This overflow is captured by DAC_OV_IS bit (INTS1, 19H...), and, if
enabled by the DAC_OV_IM bit (INTM1, 14H...), an interrupt will be generated.
3.3.3.2 LBO (Line Build Out)
To prevent the cross-talk at the far end, the output of TTIPn/TRINGn
could be attenuated before transmission for long haul applications. The
FCC Part 68 Regulations specifies four grades of attenuation with a step
of 7.5 dB. Three LBOs are used to implement the pulse attenuation. The
PULS[3:0] bits (TCF1, 05H...) are used to select the attenuation grade. Both
Table-14 and Table-15 list these values.
18
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
The following tables give all the sample data based on the preset pulse
templates and LBOs in detail for reference. For preset pulse templates and
LBOs, scaling up/down against the pulse amplitude is not supported.
1.Table-2 Transmit Waveform Value For E1 75 Ω
2.Table-3 Transmit Waveform Value For E1 120 Ω
3.Table-4 Transmit Waveform Value For T1 0~133 ft
4.Table-5 Transmit Waveform Value For T1 133~266 ft
5.Table-6 Transmit Waveform Value For T1 266~399 ft
6.Table-7 Transmit Waveform Value For T1 399~533 ft
7.Table-8 Transmit Waveform Value For T1 533~655 ft
8.Table-9 Transmit Waveform Value For J1 0~655 ft
9.Table-10 Transmit Waveform Value For DS1 0 dB LBO
10.Table-11 Transmit Waveform Value For DS1 -7.5 dB LBO
11.Table-12 Transmit Waveform Value For DS1 -15.0 dB LBO
12.Table-13 Transmit Waveform Value For DS1 -22.5 dB LBO
Table-3 Transmit Waveform Value For E1 120 Ω
Table-2 Transmit Waveform Value For E1 75 Ω
Sample
UI 1
UI 2
UI 3
UI 4
1
0000000
0000000
0000000
0000000
2
0000000
0000000
0000000
0000000
3
0000000
0000000
0000000
0000000
4
0001100
0000000
0000000
0000000
5
0110000
0000000
0000000
0000000
6
0110000
0000000
0000000
0000000
7
0110000
0000000
0000000
0000000
8
0110000
0000000
0000000
0000000
9
0110000
0000000
0000000
0000000
10
0110000
0000000
0000000
0000000
11
0110000
0000000
0000000
0000000
12
0110000
0000000
0000000
0000000
13
0000000
0000000
0000000
0000000
14
0000000
0000000
0000000
0000000
15
0000000
0000000
0000000
0000000
16
0000000
0000000
0000000
0000000
Sample
UI 1
UI 2
UI 3
UI 4
1
0000000
0000000
0000000
0000000
2
0000000
0000000
0000000
0000000
3
0000000
0000000
0000000
0000000
4
0001111
0000000
0000000
0000000
5
0111100
0000000
0000000
0000000
6
0111100
0000000
0000000
0000000
7
0111100
0000000
0000000
0000000
8
0111100
0000000
0000000
0000000
9
0111100
0000000
0000000
0000000
10
0111100
0000000
0000000
0000000
11
0111100
0000000
0000000
0000000
12
0111100
0000000
0000000
0000000
13
0000000
0000000
0000000
0000000
14
0000000
0000000
0000000
0000000
15
0000000
0000000
0000000
0000000
16
0000000
0000000
0000000
0000000
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0]
results in 3% scaling up/down against the pulse amplitude.
Table-4 Transmit Waveform Value For T1 0~133 ft
SCAL[5:0] = 100001 (default), One step change of this value of SCAL[5:0]
results in 3% scaling up/down against the pulse amplitude.
Sample
UI 1
UI 2
UI 3
UI 4
1
0010111
1000010
0000000
0000000
2
0100111
1000001
0000000
0000000
3
0100111
0000000
0000000
0000000
4
0100110
0000000
0000000
0000000
5
0100101
0000000
0000000
0000000
6
0100101
0000000
0000000
0000000
7
0100101
0000000
0000000
0000000
8
0100100
0000000
0000000
0000000
9
0100011
0000000
0000000
0000000
10
1001010
0000000
0000000
0000000
11
1001010
0000000
0000000
0000000
12
1001001
0000000
0000000
0000000
13
1000111
0000000
0000000
0000000
14
1000101
0000000
0000000
0000000
15
1000100
0000000
0000000
0000000
16
1000011
0000000
0000000
0000000
SCAL[5:0] = 1101101 (default), One step change of this value of SCAL[5:0]
results in 2% scaling up/down against the pulse amplitude.
1. In T1 mode, when arbitrary pulse for short haul application is configured,
users should write ‘110110’ to SCAL[5:0] bits if no scaling is required.
19
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-5 Transmit Waveform Value For T1 133~266 ft
Table-7 Transmit Waveform Value For T1 399~533 ft
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
0011011
1000011
0000000
0000000
1
0100000
1000011
0000000
0000000
2
0101110
1000010
0000000
0000000
2
0111011
1000010
0000000
0000000
3
0101100
1000001
0000000
0000000
3
0110101
1000001
0000000
0000000
4
0101010
0000000
0000000
0000000
4
0101111
0000000
0000000
0000000
5
0101001
0000000
0000000
0000000
5
0101110
0000000
0000000
0000000
6
0101000
0000000
0000000
0000000
6
0101101
0000000
0000000
0000000
7
0100111
0000000
0000000
0000000
7
0101100
0000000
0000000
0000000
8
0100110
0000000
0000000
0000000
8
0101010
0000000
0000000
0000000
9
0100101
0000000
0000000
0000000
9
0101000
0000000
0000000
0000000
10
1010000
0000000
0000000
0000000
10
1011000
0000000
0000000
0000000
11
1001111
0000000
0000000
0000000
11
1011000
0000000
0000000
0000000
12
1001101
0000000
0000000
0000000
12
1010011
0000000
0000000
0000000
13
1001010
0000000
0000000
0000000
13
1001100
0000000
0000000
0000000
14
1001000
0000000
0000000
0000000
14
1001000
0000000
0000000
0000000
15
1000110
0000000
0000000
0000000
15
1000110
0000000
0000000
0000000
16
1000100
0000000
0000000
0000000
16
1000100
0000000
0000000
0000000
See Table-4
See Table-4
Table-6 Transmit Waveform Value For T1 266~399 ft
Sample
UI 1
UI 2
UI 3
Table-8 Transmit Waveform Value For T1 533~655 ft
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
0011111
1000011
0000000
0000000
1
0100000
1000011
0000000
0000000
2
0110100
1000010
0000000
0000000
2
0111111
1000010
0000000
0000000
3
0101111
1000001
0000000
0000000
3
0111000
1000001
0000000
0000000
4
0101100
0000000
0000000
0000000
4
0110011
0000000
0000000
0000000
5
0101011
0000000
0000000
0000000
5
0101111
0000000
0000000
0000000
6
0101010
0000000
0000000
0000000
6
0101110
0000000
0000000
0000000
7
0101001
0000000
0000000
0000000
7
0101101
0000000
0000000
0000000
8
0101000
0000000
0000000
0000000
8
0101100
0000000
0000000
0000000
9
0100101
0000000
0000000
0000000
9
0101001
0000000
0000000
0000000
10
1010111
0000000
0000000
0000000
10
1011111
0000000
0000000
0000000
11
1010011
0000000
0000000
0000000
11
1011110
0000000
0000000
0000000
12
1010000
0000000
0000000
0000000
12
1010111
0000000
0000000
0000000
13
1001011
0000000
0000000
0000000
13
1001111
0000000
0000000
0000000
14
1001000
0000000
0000000
0000000
14
1001001
0000000
0000000
0000000
15
1000110
0000000
0000000
0000000
15
1000111
0000000
0000000
0000000
16
1000100
0000000
0000000
0000000
16
1000100
0000000
0000000
0000000
See Table-4
See Table-4
20
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-9 Transmit Waveform Value For J1 0~655 ft
Table-11 Transmit Waveform Value For DS1 -7.5 dB LBO
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
0010111
1000010
0000000
0000000
1
0000000
0010100
0000010
0000000
2
0100111
1000001
0000000
0000000
2
0000010
0010010
0000010
0000000
3
0100111
0000000
0000000
0000000
3
0001001
0010000
0000010
0000000
4
0100110
0000000
0000000
0000000
4
0010011
0001110
0000010
0000000
5
0100101
0000000
0000000
0000000
5
0011101
0001100
0000010
0000000
6
0100101
0000000
0000000
0000000
6
0100101
0001011
0000001
0000000
7
0100101
0000000
0000000
0000000
7
0101011
0001010
0000001
0000000
8
0100100
0000000
0000000
0000000
8
0110001
0001001
0000001
0000000
9
0100011
0000000
0000000
0000000
9
0110110
0001000
0000001
0000000
10
1001010
0000000
0000000
0000000
10
0111010
0000111
0000001
0000000
11
1001010
0000000
0000000
0000000
11
0111001
0000110
0000001
0000000
12
1001001
0000000
0000000
0000000
12
0110000
0000101
0000001
0000000
13
1000111
0000000
0000000
0000000
13
0101000
0000100
0000000
0000000
14
1000101
0000000
0000000
0000000
14
0100000
0000100
0000000
0000000
15
1000100
0000000
0000000
0000000
15
0011010
0000011
0000000
0000000
16
1000011
0000000
0000000
0000000
16
0010111
0000011
0000000
0000000
SCAL[5:0] = 110110 (default), One step change of this value of SCAL[5:0]
results in 2% scaling up/down against the pulse amplitude.
SCAL[5:0] = 010001 (default), One step change of this value of SCAL[5:0]
results in 6.25% scaling up/down against the pulse amplitude.
Table-10 Transmit Waveform Value For DS1 0 dB LBO
Table-12 Transmit Waveform Value For DS1 -15.0 dB LBO
Sample
UI 1
UI 2
UI 3
UI 4
Sample
UI 1
UI 2
UI 3
UI 4
1
0010111
1000010
0000000
0000000
1
0000000
0110101
0001111
0000011
2
0100111
1000001
0000000
0000000
2
0000000
0110011
0001101
0000010
3
0100111
0000000
0000000
0000000
3
0000000
0110000
0001100
0000010
4
0100110
0000000
0000000
0000000
4
0000001
0101101
0001011
0000010
5
0100101
0000000
0000000
0000000
5
0000100
0101010
0001010
0000010
6
0100101
0000000
0000000
0000000
6
0001000
0100111
0001001
0000001
7
0100101
0000000
0000000
0000000
7
0001110
0100100
0001000
0000001
8
0100100
0000000
0000000
0000000
8
0010100
0100001
0000111
0000001
9
0100011
0000000
0000000
0000000
9
0011011
0011110
0000110
0000001
10
1001010
0000000
0000000
0000000
10
0100010
0011100
0000110
0000001
11
1001010
0000000
0000000
0000000
11
0101010
0011010
0000101
0000001
12
1001001
0000000
0000000
0000000
12
0110000
0010111
0000101
0000001
13
1000111
0000000
0000000
0000000
13
0110101
0010101
0000100
0000001
14
1000101
0000000
0000000
0000000
14
0110111
0010100
0000100
0000000
15
1000100
0000000
0000000
0000000
15
0111000
0010010
0000011
0000000
16
1000011
0000000
0000000
0000000
16
0110111
0010000
0000011
0000000
SCAL[5:0] = 110110 (default), One step change of this Value results in 2%
scaling up/down against the pulse amplitude.
SCAL[5:0] = 001000 (default), One step change of the value of SCAL[5:0]
results in 12.5% scaling up/down against the pulse amplitude.
21
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
to ‘1’, the internal impedance matching circuit will be disabled. In this case,
the external impedance matching circuit will be used to realize the impedance matching. For T1/J1 mode, the external impedance matching circuit
for the transmitter is not supported.
Table-13 Transmit Waveform Value For DS1 -22.5 dB LBO
Sample
UI 1
UI 2
UI 3
UI 4
1
0000000
0101100
0011110
0001000
2
0000000
0101110
0011100
0000111
3
0000000
0110000
0011010
0000110
4
0000000
0110001
0011000
0000101
5
0000001
0110010
0010111
0000101
6
0000011
0110010
0010101
0000100
7
0000111
0110010
0010100
0000100
8
0001011
0110001
0010011
0000011
9
0001111
0110000
0010001
0000011
10
0010101
0101110
0010000
0000010
11
0011001
0101100
0001111
0000010
12
0011100
0101001
0001110
0000010
13
0100000
0100111
0001101
0000001
14
0100011
0100100
0001100
0000001
15
0100111
0100010
0001010
0000001
16
0101010
0100000
0001001
0000001
Figure-8 shows the appropriate external components to connect with
the cable for one channel. Table-14 is the list of the recommended impedance matching for transmitter.
In hardware control mode, TERMn pin can be used to select impedance
matching for both receiver and transmitter on a per channel basis. If TERMn
pin is low, internal impedance network will be used. If TERMn pin is high,
external impedance network will be used in E1 mode, or external impedance network for receiver and internal impedance network for transmitter
will be used in T1/J1 mode. (This applies to ZB die revision only). When
internal impedance network is used, PULSn[3:0] pins should be set to
select the specific internal impedance in the corresponding channel. Refer
to 5 HARDWARE CONTROL PIN SUMMARY for details.
The TTIPn/TRINGn can also be turned into high impedance globally by
pulling THZ pin to high or individually by setting the THZ bit (TCF1, 05H...)
to ‘1’. In this state, the internal transmit circuits are still active.
In hardware control mode, TTIPn/TRINGn pins can be turned into high
impedance globally by pulling THZ pin to high. Refer to 5 HARDWARE
CONTROL PIN SUMMARY for details.
SCAL[5:0] = 000100 (default), One step change of this value of SCAL[5:0]
results in 25% scaling up/down against the pulse amplitude.
3.3.4
Besides, in the following cases, TTIPn/TRINGn will also become high
impedance:
•
Loss of MCLK;
•
Loss of TCLKn (exceptions: Remote Loopback; Transmit internal
pattern by MCLK);
•
Transmit path power down;
•
After software reset; pin reset and power on.
TRANSMIT PATH LINE INTERFACE
The transmit line interface consists of TTIPn and TRINGn pins. The
impedance matching can be realized by the internal impedance matching
circuit or the external impedance matching circuit. If T_TERM[2] is set to
‘0’, the internal impedance matching circuit will be selected. In this case,
the T_TERM[1:0] bits (TERM, 02H...) can be set to choose 75 Ω, 100 Ω,
110 Ω or 120 Ω internal impedance of TTIPn/TRINGn. If T_TERM[2] is set
Table-14 Impedance Matching for Transmitter
Cable Configuration
E1/75 Ω
Internal Termination
External Termination
T_TERM[2:0]
PULS[3:0]
RT
T_TERM[2:0]
PULS[3:0]
RT
000
0000
0Ω
1XX
0001
9.4 Ω
E1/120 Ω
001
0001
T1/0~133 ft
010
0010
T1/133~266 ft
0011
T1/266~399 ft
0100
T1/399~533 ft
0101
T1/533~655 ft
0110
J1/0~655 ft
011
0111
0 dB LBO
010
1000
-7.5 dB LBO
1001
-15.0 dB LBO
1010
-22.5 dB LBO
1011
0001
-
Note: The precision of the resistors should be better than ± 1%
22
-
-
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.3.5
3.4
TRANSMIT PATH POWER DOWN
The transmit path can be powered down individually by setting the
T_OFF bit (TCF0, 04H...) to ‘1’. In this case, the TTIPn/TRINGn pins are
turned into high impedance.
RECEIVE PATH
The receive path consists of Receive Internal Termination, Monitor
Gain, Amplitude/Wave Shape Detector, Digital Tuning Controller, Adaptive
Equalizer, Data Slicer, CDR (Clock & Data Recovery), Optional Jitter Attenuator, Decoder and LOS/AIS Detector. Refer to Figure-7.
In hardware control mode, the transmit path can be powered down by
setting PATTn[1:0] pins to ‘11’ on a per channel basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.4.1
RECEIVE INTERNAL TERMINATION
The impedance matching can be realized by the internal impedance
matching circuit or the external impedance matching circuit. If R_TERM[2]
is set to ‘0’, the internal impedance matching circuit will be selected. In this
case, the R_TERM[1:0] bits (TERM, 02H...) can be set to choose 75 Ω, 100
Ω, 110 Ω or 120 Ω internal impedance of RTIPn/RRINGn. If R_TERM[2]
is set to ‘1’, the internal impedance matching circuit will be disabled. In this
case, the external impedance matching circuit will be used to realize the
impedance matching.
Figure-8 shows the appropriate external components to connect with
the cable for one channel. Table-15 is the list of the recommended impedance matching for receiver.
LOS/AIS
Detector
RTIP
RRING
Receive
Internal
termination
Adaptive
Equalizer
Monitor Gain
Clock
and Data
Recovery
Data Slicer
LOS
RCLK
Jitter
Attenuator
Decoder
RDP
RDN
Figure-7 Receive Path Function Block Diagram
Table-15 Impedance Matching for Receiver
Cable Configuration
E1/75 Ω
Internal Termination
External Termination
R_TERM[2:0]
RR
R_TERM[2:0]
RR
000
120 Ω
1XX
75 Ω
E1/120 Ω
001
120 Ω
T1
010
100 Ω
J1
011
110 Ω
23
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
•
1:1
•
•
RX Line
RR
B
2:1
• •
TX Line
VDDRn
D6
•·
•
D5 VDDTn
D4
RT
•·
D3
3.3 V
68µF 1
0.1µF
RRINGn
TTIPn
•
GNDRn
IDT82V2082
A
VDDRn
One of the Two Identical Channels
D8
•· RTIPn
VDDRn
D7
3.3 V
VDDTn
2
Cp
68µF 1
0.1µF
VDDTn
D2
RT
Note:
1. Common decoupling capacitor
2. Cp 0-560 (pF)
3. D1 - D8, Motorola - MBR0540T1;
3
D1
GNDTn
•·
•
TRINGn
International Rectifier - 11DQ04 or 10BQ060
Figure-8 Transmit/Receive Line Circuit
In hardware control mode, TERMn, PULSn[3:0] pins can be used to
select impedance matching for both receiver and transmitter on a per channel basis. If TERMn pin is low, internal impedance network will be used. If
TERMn pin is high, external impedance network will be used in E1 mode,
or external impedance network for receiver and internal impedance network for transmitter will be used in T1/J1 mode. (This applies to ZB die revision only). When internal impedance network is used, PULSn[3:0] pins
should be set to select specific internal impedance for the corresponding
channel. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.4.2
DSX cross connect
point
RTIP
monitor
gain=0dB
RRING
R
normal receive mode
RTIP
LINE MONITOR
monitor gain
=22/26/32dB
In both T1/J1 and E1 short haul applications, the non-intrusive monitoring on channels located in other chips can be performed by tapping the monitored channel through a high impedance bridging circuit. Refer to Figure9 and Figure-10.
RRING
monitor mode
Figure-9 Monitoring Receive Line in Another Chip
After a high resistance bridging circuit, the signal arriving at the RTIPn/
RRINGn is dramatically attenuated. To compensate this attenuation, the
Monitor Gain can be used to boost the signal by 22 dB, 26 dB and 32 dB,
selected by MG[1:0] bits (RCF2, 0BH...). For normal operation, the Monitor
Gain should be set to 0 dB.
DSX cross connect
point
TTIP
In hardware control mode, MONTn pin can be used to set the Monitor
Gain on a per channel basis. When MONTn pin is low, the Monitor Gain for
the specific channel is 0 dB. When MONTn pin is high, the Monitor Gain for
the specific channel is 26 dB. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
TRING
R
normal transmit mode
RTIP
monitor gain
monitor gain
=22/26/32dB
RRING
monitor mode
Figure-10 Monitor Transmit Line in Another Chip
24
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.4.3
3.4.7
ADAPTIVE EQUALIZER
INDUSTRIAL
TEMPERATURE RANGES
DECODER
The adaptive equalizer can remove most of the signal distortion due to
intersymbol interference caused by cable attenuation. It can be enabled or
disabled by setting EQ_ON bit to ‘1’ or ‘0’ (RCF1, 0AH...).
In T1/J1 applications, the R_MD[1:0] bits (RCF0, 09H...) is used to
select the AMI decoder or B8ZS decoder. In E1 applications, the R_MD[1:0]
bits (RCF0, 09H...) are used to select the AMI decoder or HDB3 decoder.
When the adaptive equalizer is out of range, EQ_S bit (STAT0, 16H...)
will be set to ‘1’ to indicate the status of equalizer. If EQ_IES bit (INTES,
15H...) is set to ‘1’, any changes of EQ_S bit will generate an interrupt and
EQ_IS bit (INTS0, 18H...) will be set to ‘1’ if it is not masked. If EQ_IES bit
is set to ‘0’, only the ‘0’ to ‘1’ transition of the EQ_S bit will generate an interrupt and EQ_IS bit will be set to ‘1’ if it is not masked. The EQ_IS bit will be
reset after being read.
When the chip is configured by hardware, the operation mode of receive
and transmit path can be selected by setting RXTXM[1:0] pins on a global
basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.4.8
The receive path system interface consists of RCLKn pin, RDn/RDPn
pin and RDNn pin. In E1 mode, the RCLKn outputs a recovered 2.048 MHz
clock. In T1/J1 mode, the RCLKn outputs a recovered 1.544 MHz clock. The
received data is updated on the RDn/RDPn and RDNn pins on the active
edge of RCLKn. The active edge of RCLKn can be selected by the
RCLK_SEL bit (RCF0, 09H...). And the active level of the data on RDn/
RDPn and RDNn can be selected by the RD_INV bit (RCF0, 09H...).
The Amplitude/wave shape detector keeps on measuring the amplitude/wave shape of the incoming signals during an observation period. This
observation period can be 32, 64, 128 or 256 symbol periods, as selected
by UPDW[1:0] bits (RCF2, 0BH...). A shorter observation period allows
quicker responses to pulse amplitude variation while a longer observation
period can minimize the possible overshoots. The default observation
period is 128 symbol periods.
In hardware control mode, only the active edge of RCLKn can be
selected. If RCLKE is set to high, the falling edge will be chosen as the active
edge of RCLKn. If RCLKE is set to low, the rising edge will be chosen as
the active edge of RCLKn. The active level of the data on RDn/RDPn and
RDNn is the same as that in software control mode.
Based on the observed peak value for a period, the equalizer will be
adjusted to achieve a normalized signal. LATT[4:0] bits (STAT1, 17H...)
indicate the signal attenuation introduced by the cable in approximately 2
dB per step.
3.4.4
RECEIVE PATH SYSTEM INTERFACE
The received data can be output to the system side in two different ways:
Single Rail or Dual Rail, as selected by R_MD bit [1] (RCF0, 09H...). In Single Rail mode, only RDn pin is used to output data and the RDNn/CVn pin
is used to report the received errors. In Dual Rail Mode, both RDPn pin and
RDNn pin are used for outputting data.
RECEIVE SENSITIVITY
For short haul application, the Receive Sensitivity for both E1 and T1/
J1 is -10 dB. For long haul application, the receive sensitivity is -43 dB for
E1 and -36 dB for T1/J1.
When the chip is configured by hardware, the short haul or long haul
operating mode can be selected by setting EQn on a per channel basis. For
short haul mode, the Receive Sensitivity for both E1 and T1/J1 is -10 dB.
For long haul mode, the receive sensitivity is -43 dB for E1 and -36 dB for
T1/J1. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
In the receive Dual Rail mode, the CDR unit can be by-passed by setting
R_MD[1:0] to ‘11’ (binary). In this situation, the output data from the Data
Slicer will be output to the RDPn/RDNn pins directly, and the RCLKn outputs the exclusive OR (XOR) of the RDPn and RDNn. This is called receiver
slicer mode. In this case, the transmit path is still operating in Dual Rail
mode.
3.4.5
3.4.9
DATA SLICER
The receive path can be powered down individually by setting R_OFF
bit (RCF0, 09H...) to ‘1’. In this case, the RCLKn, RDn/RDPn, RDNn and
LOSn will be logic low.
The Data Slicer is used to generate a standard amplitude mark or a
space according to the amplitude of the input signals. The threshold can
be 40%, 50%, 60% or 70%, as selected by the SLICE[1:0] bits (RCF2,
0BH...). The output of the Data Slicer is forwarded to the CDR (Clock & Data
Recovery) unit or to the RDPn/RDNn pins directly if the CDR is disabled.
3.4.6
RECEIVE PATH POWER DOWN
In hardware control mode, receiver power down can be selected by pulling RPDn pin to high on a per channel basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for more details.
CDR (Clock & Data Recovery)
The CDR is used to recover the clock and data from the received signal.
The recovered clock tracks the jitter in the data output from the Data Slicer
and keeps the phase relationship between data and clock during the
absence of the incoming pulse. The CDR can also be by-passed in the Dual
Rail mode. When CDR is by-passed, the data from the Data Slicer is output
to the RDPn/RDNn pins directly.
25
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
The monitored line signal (transmit or receive) goes through Channel
1’s Clock and Data Recovery. The signal can be observed digitally at the
RCLK1, RD1/RDP1 and RDN1. If Channel 1 is configured to Remote Loopback while in the Monitoring mode, the monitored data will be output on
TTIP1/TRING1.
3.4.10 G.772 NON-INTRUSIVE MONITORING
In applications using only one channel, channel 1 can be configured to
monitor the data received or transmitted in channel 2. The MONT[1:0] bits
(GCF, 20H) determine which direction (transmit/receive) will be monitored.
The monitoring is non-intrusive per ITU-T G.772. Figure-11 illustrates the
concept.
Channel 2
LOS2
LOS/AIS
Detection
RCLK2
RD2/RDP2
CV2/RDN2
B8ZS/
HDB3/AMI
Decoder
Jitter
Attenuator
TCLK2
TD2/TDP2
TDN2
B8ZS/
HDB3/AMI
Encoder
Jitter
Attenuator
Clock and
Data
Recovery
Data
Slicer
Adaptive
Equalizer
Line
Driver
Waveform
Shaper/LBO
Receiver
Internal
Termination
RTIP2
Transmitter
Internal
Termination
TTIP2
Channel 1
LOS1
RCLK1
RD1/RDP1
CV1/RDN1
DLOS/AIS
Detection
B8ZS/
HDB3/AMI
Decoder
ALOS
Detection
Jitter
Attenuator
Clock and
Data
Recovery
Data
Slicer
Adaptive
Equalizer
RRING2
TRING2
G.772
Monitor
Receiver
Internal
Termination
RTIP1
Transmitter
Internal
Termination
TTIP1
RRING1
Remote
Loopback
TCLK1
TD1/TDP1
TDN1
B8ZS/
HDB3/AMI
Encoder
Jitter
Attenuator
Line
Driver
Waveform
Shaper/LBO
Figure-11 G.772 Monitoring Diagram
26
TRING1
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.5
JITTER ATTENUATOR
In E1 applications, the Corner Frequency of the DPLL can be 0.9 Hz or
6.8 Hz, as selected by the JABW bit (JACF, 03H...). In T1/J1 applications,
the Corner Frequency of the DPLL can be 1.25 Hz or 5.00 Hz, as selected
by the JABW bit (JACF, 03H...). The lower the Corner Frequency is, the
longer time is needed to achieve synchronization.
There is one Jitter Attenuator in each channel of the LIU. The Jitter Attenuator can be deployed in the transmit path or the receive path, and can also
be disabled. This is selected by the JACF[1:0] bits (JACF, 03H...).
In hardware control mode, Jitter Attenuator position, bandwidth and the
depth of FIFO can be selected by JA[1:0] pins on a global basis. Refer to 5
HARDWARE CONTROL PIN SUMMARY for details.
3.5.1
When the incoming data moves faster than the outgoing data, the FIFO
will overflow. This overflow is captured by the JAOV_IS bit (INTS1, 19H...).
If the incoming data moves slower than the outgoing data, the FIFO will
underflow. This underflow is captured by the JAUD_IS bit (INTS1, 19H...).
For some applications that are sensitive to data corruption, the JA limit
mode can be enabled by setting JA_LIMIT bit (JACF, 03H...) to ‘1’. In the
JA limit mode, the speed of the outgoing data will be adjusted automatically
when the FIFO is close to its full or emptiness. The criteria of starting speed
adjustment are shown in Table-16. The JA limit mode can reduce the possibility of FIFO overflow and underflow, but the quality of jitter attenuation
is deteriorated.
JITTER ATTENUATION FUNCTION DESCRIPTION
The Jitter Attenuator is composed of a FIFO and a DPLL, as shown in
Figure-12. The FIFO is used as a pool to buffer the jittered input data, then
the data is clocked out of the FIFO by a de-jittered clock. The depth of the
FIFO can be 32 bits, 64 bits or 128 bits, as selected by the JADP[1:0] bits
(JACF, 03H...). In hardware control mode, the depth of FIFO can be selected
by JA[1:0] pins on a global basis. Refer to 5 HARDWARE CONTROL PIN
SUMMARY for details. Consequently, the constant delay of the Jitter Attenuator will be 16 bits, 32 bits or 64 bits. Deeper FIFO can tolerate larger jitter,
but at the cost of increasing data latency time.
Jittered Clock
W
Table-16 Criteria of Starting Speed Adjustment
Criteria for Adjusting Data Outgoing Speed
32 Bits
2 bits close to its full or emptiness
64 Bits
3 bits close to its full or emptiness
128 Bits
4 bits close to its full or emptiness
De-jittered Data
RDNn
3.5.2
JITTER ATTENUATOR PERFORMANCE
The performance of the Jitter Attenuator in the IDT82V2082 meets the
ITU-T I.431, G.703, G.736-739, G.823, G.824, ETSI 300011, ETSI TBR12/
13, AT&T TR62411 specifications. Details of the Jitter Attenuator performance is shown in Table-68 Jitter Tolerance and Table-69 Jitter Attenuator
Characteristics.
R
DPLL
FIFO Depth
RDn/RDPn
FIFO
32/64/128
Jittered Data
INDUSTRIAL
TEMPERATURE RANGES
De-jittered Clock
RCLKn
MCLK
Figure-12 Jitter Attenuator
27
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.6
LOS AND AIS DETECTION
3.6.1
LOS DETECTION
• LOS detect level threshold
In short haul mode, the amplitude threshold Q is fixed on 800 mVpp,
while P=Q+200 mVpp (200 mVpp is the LOS level detect hysteresis).
The Loss of Signal Detector monitors the amplitude of the incoming signal level and pulse density of the received signal on RTIPn and RRINGn.
In long haul mode, the value of Q can be selected by LOS[4:0] bit (RCF1,
0AH...), while P=Q+4 dB (4 dB is the LOS level detect hysteresis). The
LOS[4:0] default value is 10101 (-46 dB).
• LOS declare (LOS=1)
A LOS is detected when the incoming signal has “no transitions”, i.e.,
when the signal level is less than Q dB below nominal for N consecutive
pulse intervals. Here N is defined by LAC bit (MAINT0, 0CH...). LOS will be
declared by pulling LOSn pin to high (LOS=1) and LOS interrupt will be generated if it is not masked.
When the chip is configured by hardware, the LOS detect level is fixed
if the IDT82V2082 operates in long haul mode. It is -46dB (E1) and -38dB
(T1/J1).
• Criteria for declare and clear of a LOS detect
The detection supports the ANSI T1.231 and I.431 for T1/J1 mode and
G.775 and ETSI 300233/I.431 for E1 mode. The criteria can be selected
by LAC bit (MAINT0, 0CH...) and T1E1 bit (GCF, 20H).
• LOS clear (LOS=0)
The LOS is cleared when the incoming signal has “transitions”, i.e.,
when the signal level is greater than P dB below nominal and has an average pulse density of at least 12.5% for M consecutive pulse intervals, starting with the receipt of a pulse. Here M is defined by LAC bit (MAINT0,
0CH...). LOS status is cleared by pulling LOSn pin to low.
Table-17 and Table-18 summarize LOS declare and clear criteria for
both short haul and long haul application.
• All Ones output during LOS
On the system side, the RDPn/RDNn will reflect the input pulse “transition” at the RTIPn/RRINGn side and output recovered clock (but the quality
of the output clock can not be guaranteed when the input level is lower than
the maximum receive sensitivity) when AISE bit (MAINT0, 0CH...) is 0; or
output All Ones as AIS when AISE bit (MAINT0, 0CH...) is 1. In this case
RCLKn output is replaced by MCLK.
LOS=1
On the line side, the TTIPn/TRINGn will output All Ones as AIS when
ATAO bit (MAINT0, 0CH...) is 1. The All Ones pattern uses MCLK as the
reference clock.
signal level<Q
signal level>P
density=OK
(observing windows= M)
(observing windows= N)
LOS indicator is always active for all kinds of loopback modes.
LOS=0
Figure-13 LOS Declare and Clear
Table-17 LOS Declare and Clear Criteria for Short Haul Mode
Control bit
T1E1
LOS declare threshold
LOS clear threshold
LAC
0=T1.231
Level < 800 mVpp
N=175 bits
Level > 1 Vpp
M=128 bits
12.5% mark density
<100 consecutive zeroes
1=I.431
Level < 800 mVpp
N=1544 bits
Level > 1 Vpp
M=128 bits
12.5% mark density
<100 consecutive zeroes
Level < 800 mVpp
N=32 bits
Level > 1 Vpp
M=32 bits
12.5% mark density
<16 consecutive zeroes
Level < 800 mVpp
N=2048 bits
Level > 1 Vpp
M=32 bits
12.5% mark density
<16 consecutive zeroes
1=T1/J1
0=G.775
0=E1
1=I.431/ETSI
28
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-18 LOS Declare and Clear Criteria for Long Haul Mode
Control bit
T1E1
LAC
0
00000
00001
…
T1.231 10001
…
10101
10110-11111
1
0
Level > Q+ 4dB
M=128 bits
12.5% mark density
<100 consecutive zeroes
-4
Level < Q
N=1544 bits
Level > Q+ 4dB
M=128 bits
12.5% mark density
<100 consecutive zeroes
I.431 Level detect range is -18 to -30
dB
Level < Q
N=32 bits
Level > Q+ 4dB
M=32 bits
12.5% mark density
<16 consecutive zeroes
G.775 Level detect range is -9 to -35
dB
Level < Q
N=2048 bits
Level > Q+ 4dB
M=32 bits
12.5% mark density
<16 consecutive zeroes
I.431 Level detect range is -6 to -20 dB
-18
…
-30
01110
…
10001
…
10101
10110-11111
-32
…
-38
…
-46
-48
00000
…
00010
-4
…
-8
00011
G.775 …
10000
-10
…
-36
10001
…
10101(default)
10110-11111
-38
…
-46
-48
00000
-4
00001
I.431/ …
ETSI 01000
-6
…
-20
-
0=E1
-
1
-
3.6.2
Level < Q
N=175 bits
I.431 00111
…
01101
-
01001
…
10101(default)
10110-11111
Note
-4
-6
…
-38
…
-46
-48
-16
-
LOS clear threshold
Q (dB)
00000
…
00110
1=T1/J1
LOS declare threshold
LOS[4:0]
-22
…
-46
-48
T1.231. In E1 applications, the criteria for declaring/clearing AIS detection
comply with the ITU G.775 or the ETSI 300233, as selected by the LAC bit
(MAINT0, 0CH...). Table-19 summarizes different criteria for AIS detection
Declaring/Clearing.
AIS DETECTION
The Alarm Indication Signal can be detected by the IDT82V2082 when
the Clock & Data Recovery unit is enabled. The status of AIS detection is
reflected in the AIS_S bit (STAT0, 16H...). In T1/J1 applications, the criteria
for declaring/clearing AIS detection are in compliance with the ANSI
Table-19 AIS Condition
ITU G.775 for E1
(LAC bit is set to ‘0’ by default)
ETSI 300233 for E1
(LAC bit is set to ‘1’)
ANSI T1.231 for T1/J1
AIS
detected
Less than 3 zeros contained in each of two consecutive Less than 3 zeros contained in a 512-bit Less than 9 zeros contained in an 8192-bit stream
512-bit streams are received
stream are received
(a ones density of 99.9% over a period of 5.3ms)
AIS
cleared
3 or more zeros contained in each of two consecutive 3 or more zeros contained in a 512-bit 9 or more zeros contained in an 8192-bit stream
512-bit streams are received
stream are received
are received
29
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.7
TRANSMIT AND DETECT INTERNAL PATTERNS
PRBS data can be inverted through setting the PRBS_INV bit (MAINT0,
0CH...).
The internal patterns (All Ones, All Zeros, PRBS/QRSS pattern and
Activate/Deactivate Loopback Code) will be generated and detected by
IDT82V2082. TCLKn is used as the reference clock by default. MCLK can
also be used as the reference clock by setting the PATT_CLK bit (MAINT0,
0CH...) to ‘1’.
Any change of PRBS_S bit will be captured by PRBS_IS bit (INTS0,
18H...). The PRBS_IES bit (INTES, 15H...) can be used to determine
whether the ‘0’ to ‘1’ change of PRBS_S bit will be captured by the PRBS_IS
bit or any changes of PRBS_S bit will be captured by the PRBS_IS bit. When
the PRBS_IS bit is ‘1’, an interrupt will be generated if the PRBS_IM bit
(INTM0, 13H...) is set to ‘1’.
If the PATT_CLK bit (MAINT0, 0CH...) is set to ‘0’ and the PATT[1:0] bits
(MAINT0, 0CH...) are set to ‘00’, the transmit path will operate in normal
mode.
The received PRBS/QRSS logic errors can be counted in a 16-bit
counter if the ERR_SEL [1:0] bits (MAINT6, 12H...) are set to ‘00’. Refer to
3.9 ERROR DETECTION/COUNTING AND INSERTION for the operation
of the error counter.
When the chip is configured by hardware, the transmit path will operate
in normal mode by setting PATTn[1:0] pins to ‘00’ on a per channel basis.
Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
3.7.1
3.8
TRANSMIT ALL ONES
3.8.1
ANALOG LOOPBACK
When the ALP bit (MAINT1, 0DH...) is set to ‘1’, the corresponding channel is configured in Analog Loopback mode. In this mode, the transmit signals are looped back to the Receiver Internal Termination in the receive
path then output from RCLKn, RDn, RDPn/RDNn. At the same time, the
transmit signals are still output to TTIPn/TRINGn in transmit direction. Figure-14 shows the process.
In hardware control mode, the All Ones data can be inserted into the data
stream in transmit direction by setting PATTn[1:0] pins to ‘01’ on a per channel basis. Refer to 5 HARDWARE CONTROL PIN SUMMARY for details.
TRANSMIT ALL ZEROS
If the PATT_CLK bit (MAINT0, 0CH...) is set to ‘1’, the All Zeros will be
inserted into the transmit data stream when the PATT[1:0] bits (MAINT0,
0CH...) are set to ‘00’.
3.7.3
LOOPBACK
To facilitate testing and diagnosis, the IDT82V2082 provides four different loopback configurations: Analog Loopback, Digital Loopback,
Remote Loopback and Inband Loopback.
In transmit direction, the All Ones data can be inserted into the data
stream when the PATT[1:0] bits (MAINT0, 0CH...) are set to ‘01’. The transmit data stream is output from TTIPn/TRINGn. In this case, either TCLKn
or MCLK can be used as the transmit clock, as selected by the PATT_CLK
bit (MAINT0, 0CH...).
3.7.2
INDUSTRIAL
TEMPERATURE RANGES
In hardware control mode, Analog Loopback can be selected by setting
LPn[1:0] pins to ‘01’ on a per channel basis.
3.8.2
PRBS/QRSS GENERATION AND DETECTION
DIGITAL LOOPBACK
When the DLP bit (MAINT1, 0DH...) is set to ‘1’, the corresponding channel is configured in Digital Loopback mode. In this mode, the transmit signals are looped back to the jitter attenuator (if enabled) and decoder in
receive path, then output from RCLKn, RDn, RDPn/RDNn. At the same
time, the transmit signals are still output to TTIPn/TRINGn in transmit direction. Figure-15 shows the process.
A PRBS/QRSS will be generated in the transmit direction and detected
in the receive direction by IDT82V2082. The QRSS is 220-1 for T1/J1 applications and the PRBS is 215-1 for E1 applications, with maximum zero
restrictions according to the AT&T TR62411 and ITU-T O.151.
When the PATT[1:0] bits (MAINT0, 0CH...) are set to ‘10’, the PRBS/
QRSS pattern will be inserted into the transmit data stream with the MSB
first. The PRBS/QRSS pattern will be transmitted directly or invertedly.
Both Analog Loopback mode and Digital Loopback mode allow the
sending of the internal patterns (All Ones, All Zeros, PRBS, etc.) which will
overwrite the transmit signals. In this case, either TCLKn or MCLK can be
used as the reference clock for internal patterns transmission.
In hardware control mode, the PRBS data will be generated in the transmit direction and inserted into the transmit data stream by setting
PATTn[1:0] pins to ‘10’ on a per channel basis. Refer to 5 HARDWARE
CONTROL PIN SUMMARY for details.
In hardware control mode, Digital Loopback can be selected by setting
LPn[1:0] pins to ‘10’ on a per channel basis.
The PRBS/QRSS in the received data stream will be monitored. If the
PRBS/QRSS has reached synchronization status, the PRBS_S bit
(STAT0, 16H...) will be set to ‘1’, even in the presence of a logic error rate
less than or equal to 10-1. The criteria for setting/clearing the PRBS_S bit
are shown in Table-20.
3.8.3
REMOTE LOOPBACK
When the RLP bit (MAINT1, 0DH...) is set to ‘1’, the corresponding channel is configured in Remote Loopback mode. In this mode, the recovered
clock and data output from Clock and Data Recovery on the receive path
is looped back to the jitter attenuator (if enabled) and Waveform Shaper in
transmit path. Figure-16 shows the process.
Table-20 Criteria for Setting/Clearing the PRBS_S Bit
In hardware control mode, Remote Loopback can be selected by setting
LPn[1:0] pins to ‘11’ on a per channel basis.
PRBS/QRSS 6 or less than 6 bit errors detected in a 64 bits hopping window.
Detection
PRBS/QRSS More than 6 bit errors detected in a 64 bits hopping window.
Missing
30
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
One of the Two Identical Channels
LOSn
RCLKn
RDn/RDPn
CVn/RDNn
LOS/AIS
Detection
B8ZS/
HDB3/AMI
Decoder
Clock and
Data
Recovery
Jitter
Attenuator
Data
Slicer
Adaptive
Equalizer
Receiver
Internal
Termination
RTIPn
RRINGn
Analog
Loopback
TCLKn
TDn/TDPn
TDNn
B8ZS/
HDB3/AMI
Encoder
Jitter
Attenuator
Waveform
Shaper/LBO
Transmitter
Internal
Termination
Line
Driver
TTIPn
TRINGn
Figure-14 Analog Loopback
One of the Two Identical Channels
LOSn
RCLKn
RDn/RDPn
CVn/RDNn
LOS/AIS
Detection
B8ZS/
HDB3/AMI
Decoder
Clock and
Data
Recovery
Jitter
Attenuator
Data
Slicer
Adaptive
Equalizer
Receiver
Internal
Termination
RTIPn
RRINGn
Digital
Loopback
TCLKn
TDn/TDPn
TDNn
B8ZS/
HDB3/AMI
Encoder
Jitter
Attenuator
Waveform
Shaper/LBO
Transmitter
Internal
Termination
Line
Driver
TTIPn
TRINGn
Figure-15 Digital Loopback
One of the Two Identical Channels
LOSn
RCLKn
RDn/RDPn
CVn/RDNn
LOS/AIS
Detection
B8ZS/
HDB3/AMI
Decoder
Jitter
Attenuator
Clock and
Data
Recovery
Jitter
Attenuator
Waveform
Shaper/LBO
Data
Slicer
Adaptive
Equalizer
Receiver
Internal
Termination
RTIPn
RRINGn
Remote
Loopback
TCLKn
TDn/TDPn
TDNn
B8ZS/
HDB3/AMI
Encoder
Figure-16 Remote Loopback
31
Line
Driver
Transmitter
Internal
Termination
TTIPn
TRINGn
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.8.4
INDUSTRIAL
TEMPERATURE RANGES
6-bit-long or 8-bit-long respectively by repeating itself if it is 3-bit-long or 4bit-long.
INBAND LOOPBACK
When PATT[1:0] bits (MAINT0, 0CH...) are set to ‘11’, the corresponding channel is configured in Inband Loopback mode. In this mode, an
unframed activate/Deactivate Loopback Code is generated repeatedly in
transmit direction per ANSI T1. 403 which overwrite the transmit signals.
In receive direction, the framed or unframed code is detected per ANSI T1.
403, even in the presence of 10-2 bit error rate.
After the Activate Loopback Code has been detected in the receive data
for more than 30 ms (in E1 mode) / 40 ms (in T1/J1 mode), the IBLBA_S
bit (STAT0, 16H...) will be set to ‘1’ to declare the reception of the Activate
Loopback Code.
After the Deactivate Loopback Code has been detected in the receive
data for more than 30 ms (In E1 mode) / 40 ms (In T1/J1 mode), the IBLBD_S
bit (STAT0, 16H...) will be set to ‘1’ to declare the reception of the Deactivate
Loopback Code.
If the Automatic Remote Loopback is enabled by setting ARLP bit
(MAINT1, 0DH...) to ‘1’, the chip will establish/demolish the Remote Loopback based on the reception of the Activate Loopback Code/ Deactivate
Loopback Code for 5.1 s. If the ARLP bit (MAINT1, 0DH...) is set to ‘0’, the
Remote Loopback can also be demolished forcedly.
When the IBLBA_IES bit (INTES, 15H...) is set to ‘0’, only the ‘0’ to ‘1’
transition of the IBLBA_S bit will generate an interrupt and set the IBLBA_IS
bit (INTS0, 18H...) to ‘1’. When the IBLBA_IES bit is set to ‘1’, any changes
of the IBLBA_S bit will generate an interrupt and set the IBLBA_IS bit
(INTS0, 18H...) to ‘1’. The IBLBA_IS bit will be reset to ‘0’ after being read.
3.8.4.1 Transmit Activate/Deactivate Loopback Code
The pattern of the transmit Activate/Deactivate Loopback Code is
defined by the TIBLB[7:0] bits (MAINT3, 0FH...). Whether the code represents an Activate Loopback Code or a Deactivate Loopback Code is judged
by the far end receiver. The length of the pattern ranges from 5 bits to 8 bits,
as selected by the TIBLB_L[1:0] bits (MAINT2, 0EH...). The pattern can be
programmed to 6-bit-long or 8-bit-long respectively by repeating itself if it
is 3-bit-long or 4-bit-long. When the PATT[1:0] bits (MAINT0, 0CH...) are
set to ‘11’, the transmission of the Activate/Deactivate Loopback Code is
initiated. If the PATT_CLK bit (MAINT0, 0CH...) is set to ‘0’ and the
PATT[1:0] bits (MAINT0, 0CH...) are set to ‘00’, the transmission of the Activate/Deactivate Loopback Code will stop.
When the IBLBD_IES bit (INTES, 15H...) is set to ‘0’, only the ‘0’ to ‘1’
transition of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS
bit (INTS0, 18H...) to ‘1’. When the IBLBD_IES bit is set to ‘1’, any changes
of the IBLBD_S bit will generate an interrupt and set the IBLBD_IS bit
(INTS0, 18H...) to ‘1’. The IBLBD_IS bit will be reset to ‘0’ after being read.
3.8.4.3 Automatic Remote Loopback
When ARLP bit (MAINT1, 0DH...) is set to ‘1’, the corresponding channel is configured into the Automatic Remote Loopback mode. In this mode,
if the Activate Loopback Code has been detected in the receive data for
more than 5.1 s, the Remote Loopback (shown as Figure-16) will be established automatically, and the RLP_S bit (STAT1, 17H...) will be set to ‘1’ to
indicate the establishment of the Remote Loopback. The IBLBA_S bit
(STAT0, 16H...) is set to ‘1’ to generate an interrupt. In this case, the Remote
Loopback mode will still be kept even if the receiver stop receiving the Activate Loopback Code.
The local transmit activate/deactivate code setting should be the same
as the receive code setting in the remote end. It is the same thing for the
other way round.
3.8.4.2 Receive Activate/Deactivate Loopback Code
The pattern of the receive Activate Loopback Code is defined by the
RIBLBA[7:0] bits (MAINT4, 10H...). The length of this pattern ranges from
5 bits to 8 bits, as selected by the RIBLBA_L [1:0] bits (MAINT2, 0EH...).
The pattern can be programmed to 6-bit-long or 8-bit-long respectively by
repeating itself if it is 3-bit-long or 4-bit-long.
If the Deactivate Loopback Code has been detected in the receive data
for more than 5.1 s, the Remote Loopback will be demolished automatically,
and the RLP_S bit (STAT1, 17H...) will set to ‘0’ to indicate the demolishment of the Remote Loopback. The IBLBD_S bit (STAT0, 16H...) is set to
‘1’ to generate an interrupt.
The pattern of the receive Deactivate Loopback Code is defined by the
RIBLBD[7:0] bits (MAINT5, 11H...). The length of the receive Deactivate
Loopback Code ranges from 5 bits to 8 bits, as selected by the
RIBLBD_L[1:0] bits (MAINT2, 0EH...). The pattern can be programmed to
The Remote Loopback can also be demolished forcedly by setting
ARLP bit (MAINT1, 0DH...) to ‘0’.
32
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.9
ERROR DETECTION/COUNTING AND INSERTION
3.9.1
DEFINITION OF LINE CODING ERROR
•
The following line encoding errors can be detected and counted by the
IDT82V2082:
•
Received Bipolar Violation (BPV) Error: In AMI coding, when two
consecutive pulses of the same polarity are received, a BPV error
is declared.
•
HDB3/B8ZS Code Violation (CV) Error: In HDB3/B8ZS coding, a
CV error is declared when two consecutive BPV errors are
detected, and the pulses that have the same polarity as the previous pulse are not the HDB3/B8ZS zero substitution pulses.
Excess Zero (EXZ) Error: There are two standards defining the
EXZ errors: ANSI and FCC. The EXZ_DEF bit (MAINT6, 12H...)
chooses which standard will be adopted by the corresponding
channel to judge the EXZ error. Table-21 shows definition of EXZ.
In hardware control mode, only ANSI standard is adopted.
Table-21 EXZ Definition
EXZ Definition
3.9.2
ANSI
FCC
AMI
More than 15 consecutive zeros are detected
More than 80 consecutive zeros are detected
HDB3
More than 3 consecutive zeros are detected
More than 3 consecutive zeros are detected
B8ZS
More than 7 consecutive zeros are detected
More than 7 consecutive zeros are detected
ERROR DETECTION AND COUNTING
Auto Report Mode
(CNT_MD=1)
Which type of the receiving errors (Received CV/BPV errors, excess
zero errors and PRBS logic errors) will be counted is determined by
ERR_SEL[1:0] bits (MAINT6, 12H...). Only one type of receiving error can
be counted at a time except that when the ERR_SEL[1:0] bits are set to ‘11’,
both CV/BPV and EXZ errors will be detected and counted.
counting
The selected type of receiving errors is counted in an internal 16-bit Error
Counter. Once an error is detected, an error interrupt which is indicated by
corresponding bit in (INTS1, 19H...) will be generated if it is not masked.
This Error Counter can be operated in two modes: Auto Report Mode and
Manual Report Mode, as selected by the CNT_MD bit (MAINT6, 12H...).
In Single Rail mode, once BPV or CV errors are detected, the CVn pin will
be driven to high for one RCLK period.
N
One-Second Timer expired?
CNT0, CNT1
counter
0
next second
repeats the
same process
Y
data in counter
Bit TMOV_IS is set to '1'
• Auto Report Mode
In Auto Report Mode, the internal counter starts to count the received
errors when the CNT_MD bit (MAINT6, 12H...) is set to ‘1’. A one-second
timer is used to set the counting period. The received errors are counted
within one second. If the one-second timer expires, the value in the internal
counter will be transferred to (CNT0, 1AH...) and (CNT1, 1BH...), then the
internal counter will be reset and start to count received errors for the next
second. The errors occurred during the transfer will be accumulated to the
next round. The expiration of the one-second timer will set TMOV_IS bit
(INTS1, 19H...) to ‘1’, and will generate an interrupt if the TIMER_IM bit
(INTM1, 14H...) is set to ‘0’. The TMOV_IS bit (INTS1, 19H...) will be cleared
after the interrupt register is read. The content in the (CNT0, 1AH...) and
(CNT1, 1BH...) should be read within the next second. If the counter overflows, a counter overflow interrupt which is indicated by CNT_OV_IS bit
(INTS1, 19H...) will be generated if it is not masked by CNT_IM bit (INTM1,
14H...).
read the data in CNT0, CNT1 within
the next second
Bit TMOV_IS is cleared after
the interrupt register is read
Figure-17 Auto Report Mode
33
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
• Manual Report Mode
In Manual Report Mode, the internal Error Counter starts to count the
received errors when the CNT_MD bit (MAINT6, 12H...) is set to ‘0’. When
there is a ‘0’ to ‘1’ transition on the CNT_TRF bit (MAINT6, 12H...), the data
in the counter will be transferred to (CNT0, 1AH...) and (CNT1, 1BH...), then
the counter will be reset. The errors occurred during the transfer will be
accumulated to the next round. If the counter overflows, a counter overflow
interrupt indicated by CNT_OV_IS bit (INTS1, 19H...) will be generated if
it is not masked by CNT_IM bit (INTM1, 14H...).
3.9.3
A ‘0’ to ‘1’ transition on the EER_INS bit (MAINT6, 12H...) will generate
a logic error during the PRBS/QRSS transmission.
3.10 LINE DRIVER FAILURE MONITORING
The transmit driver failure monitor can be enabled or disabled by setting
DFM_OFF bit (TCF1, 05H...). If the transmit driver failure monitor is
enabled, the transmit driver failure will be captured by DF_S bit (STAT0,
16H...). The transition of the DF_S bit is reflected by DF_IS bit (INTS0,
18H...), and, if enabled by DF_IM bit (INTM0, 13H...), will generate an interrupt. When there is a short circuit on the TTIPn/TRINGn port, the output current will be limited to 100 mA (typical), and an interrupt will be generated.
counting
N
A '0' to '1' transition
on CNT_TRF?
CNT0, CNT1
counter
counter 0
data in
BIPOLAR VIOLATION AND PRBS ERROR INSERTION
Only when three consecutive ‘1’s are detected in the transmit data
stream, will a ‘0’ to ‘1’ transition on the BPV_INS bit (MAINT6, 12H...) generate a bipolar violation pulse, and the polarity of the second ‘1’ in the series
will be inverted.
Manual Report mode
(CNT_MD=0)
Y
INDUSTRIAL
TEMPERATURE RANGES
In hardware control mode, the transmit driver failure monitor is always
enabled.
next round
repeat the
same process
Read the data in CNT0,
CNT1 within next round1
Reset CNT_TRF for the
next '0' to '1' transition
Figure-18 Manual Report Mode
Note: It is recommended that users should do the followings within next round of error counting: Read the data in CNT0 and CNT1; Reset CNT_TRF bit for the next ‘0’ to ‘1’ transition on this bit.
34
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.11 MCLK AND TCLK
3.11.2 TRANSMIT CLOCK (TCLK)
3.11.1 MASTER CLOCK (MCLK)
TCLKn is used to sample the transmit data on TDn/TDPn, TDNn. The
active edge of TCLKn can be selected by the TCLK_SEL bit (TCF0, 04H...).
During Transmit All Ones, PRBS/QRSS patterns or Inband Loopback
Code, either TCLKn or MCLK can be used as the reference clock. This is
selected by the PATT_CLK bit (MAINT0, 0CH...).
MCLK is an independent, free-running reference clock. MCLK is 1.544
MHz for T1/J1 applications and 2.048 MHz in E1 mode. This reference clock
is used to generate several internal reference signals:
•
Timing reference for the integrated clock recovery unit.
•
Timing reference for the integrated digital jitter attenuator.
•
Timing reference for microcontroller interface.
•
Generation of RCLK signal during a loss of signal condition if AIS is
enabled.
•
Reference clock during Transmit All Ones (TAOS), all zeros, PRBS/
QRSS and Inband Loopback code if it is selected as the reference
clock. For ATAO and AIS, MCLK is always used as the reference
clock.
•
Reference clock during Transmit All Ones (TAO) condition or sending PRBS/QRSS in hardware control mode.
But for Automatic Transmit All Ones and AIS, only MCLK is used as the
reference clock and the PATT_CLK bit is ignored. In Automatic Transmit
All Ones condition, the ATAO bit (MAINT0, 0CH) is set to ‘1’. In AIS condition, the AISE bit (MAINT0, 0CH) is set to ‘1’.
If TCLKn has been missing for more than 70 MCLK cycles, TCLK_LOS
bit (STAT0, 16H...) will be set, and the corresponding TTIPn/TRINGn will
become high impedance if this channel is not used for remote loopback or
is not using MCLK to transmit internal patterns (TAOS, All Zeros, PRBS and
in-band loopback code). When TCLK is detected again, TCLK_LOS bit
(STAT0, 16H...) will be cleared. The reference frequency to detect a TCLK
loss is derived from MCLK.
Figure-19 shows the chip operation status in different conditions of
MCLK and TCLKn. The missing of MCLK will set all the TTIPn/TRINGn to
high impedance state.
MCLK=H/L?
Clocked
yes
both the transmitters high
impedance
L/H
TCLKn status?
generate transmit clock loss
interrupt if not masked in
software control mode;
transmitter n high impedance
Figure-19 TCLK Operation Flowchart
35
clocked
normal operation
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.12 MICROCONTROLLER INTERFACES
is selected. When MODE[1:0] pins are set to ‘11’, Parallel-non-MultiplexedIntel Interface is selected. Refer to 8 MICROCONTROLLER INTERFACE
TIMING CHARACTERISTICS for details.
The microcontroller interface provides access to read and write the registers in the device. The chip supports serial microcontroller interface and
two kinds of parallel microcontroller interface: Motorola non-Multiplexed
mode and Intel non-Multiplexed mode. Different microcontroller interfaces
can be selected by setting MODE[1:0] pins to different values. Refer to
MODE1 and MODE0 in pin description and 8 MICROCONTROLLER
INTERFACE TIMING CHARACTERISTICS for details
3.12.2 SERIAL MICROCONTROLLER INTERFACE
When MODE[1:0] pins are set to ‘01’, Serial Interface is selected. In this
mode, the registers are programmed through a 16-bit word which contains
an 8-bit address/command byte (6 address bits A0~A5 and bit R/W) and
an 8-bit data byte (D0~D7). When bit R/W is ‘1’, data is read out from pin
SDO. When bit R/W is ‘0’, data is written into SDI pin. Refer to Figure-20.
3.12.1 PARALLEL MICROCONTROLLER INTERFACE
The interface is compatible with Motorola or Intel microcontroller. When
MODE[1:0] pins are set to ‘10’, Parallel-non-Multiplexed-Motorola interface
CS
SCLK
SDI
A0
A1
A2
A3
A4
A5 R/W
-
D0
address/command byte
D1
D2
D3
D4
D5
D6
D7
input data byte (R/W=0)
SDO
D0
remains high impedance
D1
D2
D3
D4
D5
D6
output data byte (R/W=1)
Figure-20 Serial Microcontroller Interface Function Timing
36
D7
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
3.13 INTERRUPT HANDLING
of all the channels (INTS0, 18H...) or (INTS1, 19H...) will all the bits in the
INTCH register (21H) be reset and the INT pin become inactive.
All kinds of interrupt of the IDT82V2082 are indicated by the INT pin.
When the INT_PIN[0] bit (GCF, 20H) is ‘0’, the INT pin is open drain active
low, with a 10 KΩ external pull-up resistor. When the INT_PIN[1:0] bits
(GCF, 20H) are ‘01’, the INT pin is push-pull active low; when the
INT_PIN[1:0] bits are ‘10’, the INT pin is push-pull active high.
There are totally fourteen kinds of events that could be the interrupt
source for one channel:
(1).LOS Detected
(2).AIS Detected
(3).Driver Failure Detected
(4).TCLK Loss
(5).Synchronization Status of PRBS
(6).PRBS Error Detected
(7).Code Violation Received
(8).Excessive Zeros Received
(9).JA FIFO Overflow/Underflow
(10).Inband Loopback Code Status
All the interrupt can be disabled by the INTM_GLB bit (GCF, 20H). When
the INTM_GLB bit (GCF, 20H) is set to ‘0’, an active level on the INT pin
represents an interrupt of the IDT82V2082. The INT_CH[1:0] (GCF, 20H)
should be read to identify which channel(s) generate the interrupt.
The interrupt event is captured by the corresponding bit in the Interrupt
Status Register (INTS0, 18H...) or (INTS1, 19H...). Every kind of interrupt
can be enabled/disabled individually by the corresponding bit in the register
(INTM0, 13H...) or (INTM1, 14H...). Some event is reflected by the corresponding bit in the Status Register (STAT0, 16H...) or (STAT1, 17H...), and
the Interrupt Trigger Edge Selection Register can be used to determine how
the Status Register sets the Interrupt Status Register.
(11).Equalizer Out of Range
(12).One-Second Timer Expired
(13). Error Counter Overflow
(14).Arbitrary Waveform Generator Overflow
Table-22 is a summary of all kinds of interrupt and the associated Status
bit, Interrupt Status bit, Interrupt Trigger Edge Selection bit and Interrupt
Mask bit.
After the Interrupt Status Register (INTS0, 18H...) or (INTS1, 19H...) is
read, the corresponding bit indicating which channel generates the interrupt in the INTCH register (21H) will be reset. Only when all the pending
interrupt is acknowledged through reading the Interrupt Status Registers
Table-22 Interrupt Event
Interrupt Event
Status bit
(STAT0, STAT1)
Interrupt Status bit
(INTS0, INTS1)
Interrupt Edge Selection
bit
(INTES)
Interrupt Mask bit
(INTM0, INTM1)
LOS Detected
LOS_S
LOS_IS
LOS_IES
LOS_IM
AIS Detected
AIS_S
AIS_IS
AIS_IES
AIS_IM
Driver Failure Detected
DF_S
DF_IS
DF_IES
DF_IM
TCLK Loss
TCLK_LOS
TCLK_LOS_IS
TCLK_IES
TCLK_IM
Synchronization Status of PRBS/QRSS
PRBS_S
PRBS_IS
PRBS_IES
PRBS_IM
ERR_IS
PRBS/QRSS Error
ERR_IM
Code Violation Received
CV_IS
CV_IM
Excessive Zeros Received
EXZ_IS
EXZ_IM
JA FIFO Overflow
JAOV_IS
JAOV_IM
JA FIFO Underflow
JAUD_IS
JAUD_IM
Equalizer Out of Range
EQ_S
EQ_IS
EQ_IES
EQ_IM
Inband Loopback Activate Code Status
IBLBA_S
IBLBA_IS
IBLBA_IES
IBLBA_IM
Inband Loopback Deactivate Code Status
IBLBD_S
IBLBD_IS
IBLBD_IES
TMOV_IS
One-Second Timer Expired
IBLBD_IM
TIMER_IM
Error Counter Overflow
CNT_OV_IS
CNT_IM
Arbitrary Waveform Generator Overflow
DAC_OV_IS
DAC_OV_IM
3.14 5V TOLERANT I/O PINS
•
All digital input pins will tolerate 5.0 ± 10% volts and are compatible with
TTL logic.
Hardware Reset: Asserting the RST pin low for a minimum of 100 ns
will reset the chip.
After reset, all drivers output are in high impedance state, all the internal
flip-flops are reset, and all the registers are initialized to default values.
3.15 RESET OPERATION
3.16 POWER SUPPLY
The chip can be reset in two ways:
•
Software Reset: Writing to the RST register (01H) will reset the chip
in 1 µs.
This chip uses a single 3.3 V power supply.
37
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4
PROGRAMMING INFORMATION
4.1
REGISTER LIST AND MAP
Local Registers. If the configuration of both of the two channels is the same,
the COPY bit (GCF, 20H) can be set to ‘1’ to establish the Broadcasting
mode. In the Broadcasting mode, the Writing operation on any of the two
channels’ registers will be copied to the corresponding registers of the other
channel.
The IDT82V2082 registers can be divided into Global Registers and
Local Registers. The operation on the Global Registers affects both of the
two channels while the operation on Local Registers only affects the specific channel. For different channel, the address of Local Register is different. Table-23 is the map of Global Registers and Table-24 is the map of
Table-23 Global Register List and Map
Address (hex)
CH1
Register
R/W
CH2
MAP
b7
b6
b5
b4
b3
b2
b1
b0
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
00
ID
R
01
RST
W
20
GCF
R/W
MONT1
MONT0
-
T1E1
COPY
INTM_GLB
INT_PIN1
INT_PIN0
21
INTCH
R
-
-
-
-
-
-
INT_CH2
INT_CH1
38
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-24 Per Channel Register List and Map
Address (hex)
CH1
Register
R/W
CH2
MAP
b7
b6
b5
b4
b3
b2
b1
b0
R/W
-
-
T_TERM2
T_TERM1
T_TERM0
R_TERM2
R_TERM1
R_TERM0
R/W
-
-
JA_LIMIT
JACF1
JACF0
JADP1
JADP0
JABW
R/W
-
-
-
T_OFF
TD_INV
TCLK_SEL
T_MD1
T_MD0
Transmit and receive termination register
02
22
TERM
Jitter attenuation control register
03
23
JACF
Transmit path control registers
04
24
TCF0
05
25
TCF1
R/W
-
-
DFM_OFF
THZ
PULS3
PULS2
PULS1
PULS0
06
26
TCF2
R/W
-
-
SCAL5
SCAL4
SCAL3
SCAL2
SCAL1
SCAL0
07
27
TCF3
R/W
DONE
RW
UI1
UI0
SAMP3
SAMP2
SAMP1
SAMP0
08
28
TCF4
R/W
-
WDAT6
WDAT5
WDAT4
WDAT3
WDAT2
WDAT1
WDAT0
R/W
-
-
-
R_OFF
RD_INV
RCLK_SEL
R_MD1
R_MD0
Receive path control registers
09
29
RCF0
0A
2A
RCF1
R/W
-
EQ_ON
-
LOS4
LOS3
LOS2
LOS1
LOS0
0B
2B
RCF2
R/W
-
-
SLICE1
SLICE0
UPDW1
UPDW0
MG1
MG0
R/W
-
PATT1
PATT0
PATT_CLK
PRBS_INV
LAC
AISE
ATAO
-
-
-
-
ARLP
RLP
ALP
DLP
R/W
-
-
TIBLB_L1
TIBLB_L0
RIBLBA_L1
RIBLBA_L0
RIBLBD_L1
RIBLBD_L0
Network Diagnostics control registers
0C
2C
MAINT0
0D
2D
MAINT1
0E
2E
MAINT2
0F
2F
MAINT3
R/W
TIBLB7
TIBLB6
TIBLB5
TIBLB4
TIBLB3
TIBLB2
TIBLB1
TIBLB0
10
30
MAINT4
R/W
RIBLBA7
RIBLBA6
RIBLBA5
RIBLBA4
RIBLBA3
RIBLBA2
RIBLBA1
RIBLBA0
11
31
MAINT5
R/W
RIBLBD7
RIBLBD6
RIBLBD5
RIBLBD4
RIBLBD3
RIBLBD2
RIBLBD1
RIBLBD0
12
32
MAINT6
R/W
-
BPV_INS
ERR_INS
EXZ_DEF
ERR_SEL1
ERR_SEL0
CNT_MD
CNT_TRF
IBLBA_IM
IBLBD_IM
PRBS_IM
TCLK_IM
DF_IM
AIS_IM
LOS_IM
Interrupt control registers
13
33
INTM0
R/W
EQ_IM
14
34
INTM1
R/W
DAC_OV_IM
JAOV_IM
JAUD_IM
ERR_IM
EXZ_IM
CV_IM
TIMER_IM
CNT_IM
15
35
INTES
R/W
EQ_IES
IBLBA_IES
IBLBD_IES
PRBS_IES
TCLK_IES
DF_IES
AIS_IES
LOS_IES
Line status registers
16
36
STAT0
R
EQ_S
IBLBA_S
IBLBD_S
PRBS_S
TCLK_LOS
DF_S
AIS_S
LOS_S
17
37
STAT1
R
-
-
RLP_S
LATT4
LATT3
LATT2
LATT1
LATT0
Interrupt status registers
18
38
INTS0
R
EQ_IS
IBLBA_IS
IBLBD_IS
PRBS_IS
TCLK_LOS_IS
DF_IS
AIS_IS
LOS_IS
19
39
INTS1
R
DAC_OV_IS
JAOV_IS
JAUD_IS
ERR_IS
EXZ_IS
CV_IS
TMOV_IS
CNT_OV_IS
Counter registers
1A
3A
CNT0
R
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
1B
3B
CNT1
R
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
39
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2
REGISTER DESCRIPTION
4.2.1
GLOBAL REGISTERS
Table-25 ID: Device Revision Register
(R, Address = 00H)
Symbol
Bit
Default
ID[7:0]
7-0
00H
Description
00H is for the first version.
Table-26 RST: Reset Register
(W, Address = 01H)
Symbol
Bit
Default
Description
RST[7:0]
7-0
00H
Software reset. A write operation on this register will reset all internal registers to their default values, and the status
of all ports are set to the default status. The content in this register can not be changed.
Table-27 GCF: Global Configuration Register
(R/W, Address = 20H)
Symbol
Bit
Default
MONT[1:0]
7-6
00
Description
G.772 monitor
= 00/10: Normal
= 01: Receiver 1 monitors the receive path of channel 2
= 11: Receiver 1 monitors the transmit path of channel 2
-
5
0
Reserved.
T1E1
4
0
This bit selects the E1 or T1/J1 operation mode globally.
= 0: E1 mode is selected.
= 1: T1/J1 mode is selected.
COPY
3
0
Enable broadcasting mode.
= 0: Broadcasting mode disabled
= 1: Broadcasting mode enabled. Writing operation on one channel's register will be copied exactly to the corresponding registers in other channel.
INTM_GLB
2
1
Global interrupt enable
= 0: Interrupt is globally enabled. But for each individual interrupt, it still can be disabled by its corresponding Interrupt mask Bit.
= 1: All the interrupts are disabled for both channels.
INT_PIN[1:0]
1-0
00
Interrupt pin control
= x0: Open drain, active low (with an external pull-up resistor)
= 01: Push-pull, active low
= 11: Push-pull, active high
Table-28 INTCH: Interrupt Channel Indication Register
(R, Address =21H)
Symbol
Bit
Default
-
7-2
000000
INT_CH[1:0]
1-0
00
Description
Reserved.
INT_CH[n]=0 indicates that an interrupt was generated by channel [n+1].
40
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.2
TRANSMIT AND RECEIVE TERMINATION REGISTER
Table-29 TERM: Transmit and Receive Termination Configuration Register
(R/W, Address = 02H, 22H)
Symbol
Bit
Default
Description
-
7-6
00
Reserved.
T_TERM[2:0]
5-3
000
These bits select the internal termination for transmit line impedance matching.
= 000: Internal 75 Ω impedance matching
= 001: Internal 120 Ω impedance matching
= 010: Internal 100 Ω impedance matching
= 011: Internal 110 Ω impedance matching
= 1xx: Selects external impedance matching resistors for E1 mode only. T1/J1 does not require external impedance
resistors (see Table-14).
R_TERM[2:0]
2-0
000
These bits select the internal termination for receive line impedance matching.
= 000: Internal 75 Ω impedance matching
= 001: Internal 120 Ω impedance matching
= 010: Internal 100 Ω impedance matching
= 011: Internal 110 Ω impedance matching
= 1xx: Selects external impedance matching resistors (see Table-15).
4.2.3
JITTER ATTENUATION CONTROL REGISTER
Table-30 JACF: Jitter Attenuation Configuration Register
(R/W, Address = 03H, 23H)
Symbol
Bit
Default
Description
-
7-6
00
Reserved.
JA_LIMIT
5
1
= 0: Normal mode
= 1: JA limit mode
JACF[1:0]
4-3
00
Jitter Attenuation configuration
= 00/10: JA not used
= 01: JA in transmit path
= 11: JA in receive path
JADP[1:0]
2-1
00
Jitter Attenuation depth select
= 00: 128 bits
= 01: 64 bits
= 1x: 32 bits
JABW
0
0
Jitter transfer function bandwidth select
= 0: 6.8 Hz (E1)
5 Hz (T1/J1)
=1: 0.9 Hz (E1)
1.25 Hz (T1/J1)
41
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.4
TRANSMIT PATH CONTROL REGISTERS
Table-31 TCF0: Transmitter Configuration Register 0
(R/W, Address = 04H, 24H)
Symbol
Bit
Default
Description
-
7-5
000
T_OFF
4
0
Reserved
Transmitter power down enable
= 0: Transmitter power up
= 1: Transmitter power down (line driver high impedance)
TD_INV
3
0
Transmit data invert
= 0: Data on TDn or TDPn/TDNn is active high
= 1: Data on TDn or TDPn/TDNn is active low
TCLK_SEL
2
0
Transmit clock edge select
= 0: Data on TDPn/TDNn is sampled on the falling edge of TCLKn
= 1: Data on TDPn/TDNn is sampled on the rising edge of TCLKn
T_MD[1:0]
0-1
00
Transmitter operation mode control
T_MD[1:0] select different stages of the transmit data path
= 00: Enable HDB3/B8ZS encoder and waveform shaper blocks. Input on pin TDn is single rail NRZ data
= 01: Enable AMI encoder and waveform shaper blocks. Input on pin TDn is single rail NRZ data
= 1x: Encoder is bypassed, dual rail NRZ transmit data input on pin TDPn/TDNn
Table-32 TCF1: Transmitter Configuration Register 1
(R/W, Address = 05H, 25H)
Symbol
Bit
Default
Description
-
7-6
00
Reserved. This bit should be ‘0’ for normal operation.
DFM_OFF
5
0
Transmit driver failure monitor disable
= 0: DFM is enabled
= 1: DFM is disabled
THZ
4
1
Transmit line driver high impedance enable
= 0: Normal state
= 1: Transmit line driver high impedance enable (other transmit path still work normally).
PULS[3:0]
3-0
0000
These bits select the transmit template/LBO for short-haul/long-haul applications.
T1/E1/J1
TCLK
Cable impedance
Cable range or
LBO
Allowable Cable
loss
00001
E1
2.048 MHz
75 Ω
-
0-43 dB
0001
E1
2.048 MHz
120 Ω
-
0-43 dB
0010
DSX1
1.544 MHz
100 Ω
0-133 ft
0-0.6 dB
0011
DSX1
1.544 MHz
100 Ω
133-266 ft
0.6-1.2 dB
0100
DSX1
1.544 MHz
100 Ω
266-399 ft
1.2-1.8 dB
0101
DSX1
1.544 MHz
100 Ω
399-533 ft
1.8-2.4 dB
0110
DSX1
1.544 MHz
100 Ω
533-655 ft
2.4-3.0 dB
0111
J1
1.544 MHz
110 Ω
0-655 ft
0-3.0 dB
1000
DS1
1.544 MHz
100 Ω
0 dB LBO
0-36 dB
1001
DS1
1.544 MHz
100 Ω
-7.5 dB LBO
0-28.5 dB
1010
DS1
1.544 MHz
100 Ω
-15.0 dB LBO
0-21 dB
1011
DS1
1.544 MHz
100 Ω
-22.5 dB LBO
0-13.5 dB
11xx
User programmable waveform setting
1. In internal impedance matching mode, for E1/75 Ω cable impedance, the PULS[3:0] bits (TCF1, 05H...) should be set to ‘0000’. In external impedance matching
mode, for E1/75 Ω cable impedance, the PULS[3:0] bits should be set to ‘0001’.
42
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-33 TCF2: Transmitter Configuration Register 2
(R/W, Address = 06H, 26H)
Symbol
Bit
Default
-
7-6
00
SCAL[5:0]
5-0
100001
Description
Reserved.
SCAL specifies a scaling factor to be applied to the amplitude of the user-programmable arbitrary pulses which is
to be transmitted if needed. The default value of SCAL[5:0] is ‘100001’. Refer to 3.3.3.3 User-Programmable Arbitrary Waveform.
= 110110: Default value for T1 0~133 ft, T1 133~266 ft, T1 266~399 ft, T1 399~533 ft, T1 533~655 ft, J1 0~655 ft,
DS1 0 dB LBO. One step change of this value results in 2% scaling up/down against the pulse amplitude.
= 010001: Default value for DS1 -7.5 dB LBO. One step change of this value results in 6.25% scaling up/down
against the pulse amplitude.
= 001000: Default value for DS1 -15.0 dB LBO. One step change of this value results in 12.5% scaling up/down
against the pulse amplitude.
= 000100: Default value for DS1 -22.5 dB LBO. One step change of this value results in 25% scaling up/down
against the pulse amplitude.
= 100001: Default value for E1 75 Ω and 120 Ω. One step change of this value results in 3% scaling up/down
against the pulse amplitude.
Table-34 TCF3: Transmitter Configuration Register 3
(R/W, Address = 07H, 27H)
Symbol
Bit
Default
DONE
7
0
After ‘1’ is written to this bit, a read or write operation is implemented.
Description
RW
6
0
This bit selects read or write operation
= 0: Write to RAM
= 1: Read from RAM
UI[1:0]
5-4
00
These bits specify the unit interval address. There are totally 4 unit intervals.
= 00: UI address is 0 (The most left UI)
= 01: UI address is 1
= 10: UI address is 2
= 11: UI address is 3
SAMP[3:0]
3-0
0000
These bits specify the sample address. Each UI has totally 16 samples.
= 0000: Sample address is 0 (The most left sample)
= 0001: Sample address is 1
= 0010: Sample address is 2
……
= 1110: Sample address is 14
= 1111: Sample address is 15
Table-35 TCF4: Transmitter Configuration Register 4
(R/W, Address = 08H, 28H)
Symbol
Bit
Default
-
7
0
WDAT[6:0]
6-0
0000000
Description
Reserved
In Indirect Write operation, the WDAT[6:0] will be loaded to the pulse template RAM, specifying the amplitude of
the Sample.
After an Indirect Read operation, the amplitude data of the Sample in the pulse template RAM will be output to the
WDAT[6:0].
43
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.5
RECEIVE PATH CONTROL REGISTERS
Table-36 RCF0: Receiver Configuration Register 0
(R/W, Address = 09H, 29H)
Symbol
Bit
Default
Description
-
7-5
000
R_OFF
4
0
Receiver power down enable
= 0: Receiver power up
= 1: Receiver power down
Reserved
RD_INV
3
0
Receive data invert
= 0: Data on RDn or RDPn/RDNn is active high
= 1: Data on RDn or RDPn/RDNn is active low
RCLK_SEL
2
0
Receive clock edge select (this bit is ignored in slicer mode)
= 0: Data on RDn or RDPn/RDNn is updated on the rising edge of RCLKn
= 1: Data on RDn or RDPn/RDNn is updated on the falling edge of RCLKn
R_MD[1:0]
1-0
00
Receive path decoding selection
= 00: Receive data is HDB3 (E1)/B8ZS (T1/J1) decoded and output on RDn pin with single rail NRZ format
= 01: Receive data is AMI decoded and output on RDn pin with single rail NRZ format
= 10: Decoder is bypassed, re-timed dual rail data with NRZ format output on RDPn/RDNn (dual rail mode with clock
recovery)
= 11: CDR and decoder are bypassed, slicer data with RZ format output on RDPn/RDNn (slicer mode)
44
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-37 RCF1: Receiver Configuration Register 1
(R/W, Address= 0AH, 2AH)
Symbol
Bit
Default
-
7
0
Reserved
EQ_ON
6
0
= 0: Receive equalizer off (short haul receiver)
= 1: Receive equalizer on (long haul receiver)
Reserved.
-
5
0
LOS[4:0]
4:0
10101
Description
LOS Clear Level (dB)
LOS Declare Level (dB)
00000
0
<-4
00001
>-2
<-6
00010
>-4
<-8
00011
>-6
<-10
00100
>-8
<-12
00101
>-10
<-14
00110
>-12
<-16
00111
>-14
<-18
01000
>-16
<-20
01001
>-18
<-22
01010
>-20
<-24
01011
>-22
<-26
01100
>-24
<-28
01101
>-26
<-30
01110
>-28
<-32
01111
>-30
<-34
10000
>-32
<-36
10001
>-34
<-38
10010
>-36
<-40
10011
>-38
<-42
10100
>-40
<-44
10101
>-42
<-46
10110 -11111
>-44
<-48
45
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-38 RCF2: Receiver Configuration Register 2
(R/W, Address = 0BH, 2BH)
Symbol
Bit
Default
-
7-6
00
Reserved.
SLICE[1:0]
5-4
01
Receive slicer threshold
= 00: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 40% of the peak amplitude.
= 01: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 50% of the peak amplitude.
= 10: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 60% of the peak amplitude.
= 11: The receive slicer generates a mark if the voltage on RTIPn/RRINGn exceeds 70% of the peak amplitude.
UPDW[1:0]
3-2
10
Equalizer observation window
= 00: 32 bits
= 01: 64 bits
= 10: 128 bits
= 11: 256 bits
MG[1:0]
1-0
00
Monitor gain setting: these bits select the internal linear gain boost
= 00: 0 dB
= 01: 22 dB
= 10: 26 dB
= 11: 32 dB
4.2.6
Description
NETWORK DIAGNOSTICS CONTROL REGISTERS
Table-39 MAINT0: Maintenance Function Control Register 0
(R/W, Address = 0CH, 2CH)
Symbol
Bit
Default
Description
-
7
0
Reserved.
PATT[1:0]
6-5
00
These bits select the internal pattern and insert it into transmit data stream.
= 00: Normal operation (PATT_CLK = 0) / insert all zeros (PATT_CLK = 1)
= 01: Insert All Ones
= 10: Insert PRBS (E1: 215-1) or QRSS (T1/J1: 220-1)
= 11: Insert programmable Inband loopback activate or deactivate code (default value 00001)
PATT_CLK
4
0
Selects reference clock for transmitting internal pattern
= 0: Uses TCLKn as the reference clock
= 1: Uses MCLK as the reference clock
PRBS_INV
3
0
Inverts PRBS
= 0: The PRBS data is not inverted
= 1: The PRBS data is inverted before transmission and detection
LAC
2
0
LOS/AIS criterion is selected as below:
= 0: G.775 (E1) / T1.231 (T1/J1)
= 1: ETSI 300233& I.431 (E1) / I.431 (T1/J1)
AISE
1
0
AIS enable during LOS
= 0: AIS insertion on RDPn/RDNn/RCLKn is disabled during LOS
= 1: AIS insertion on RDPn/RDNn/RCLKn is enabled during LOS
ATAO
0
0
Automatically Transmit All Ones (enabled only when PATT[1:0] = 01)
= 0: Disabled
= 1: Automatically Transmit All Ones pattern at TTIPn/TRINGn during LOS
46
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-40 MAINT1: Maintenance Function Control Register 1
(R/W, Address= 0DH, 2DH)
Symbol
Bit
Default
-
7-4
0000
Description
ARLP
3
0
Automatic remote loopback enable
= 0: Disables automatic remote loopback (normal transmit and receive operation)
= 1: Enables automatic remote loopback
RLP
2
0
Remote loopback enable
= 0: Disables remote loopback (normal transmit and receive operation)
= 1: Enables remote loopback
ALP
1
0
Analog loopback enable
= 0: Disables analog loopback (normal transmit and receive operation)
= 1: Enables analog loopback
DLP
0
0
Digital loopback enable
= 0: Disables digital loopback (normal transmit and receive operation)
= 1: Enables digital loopback
Reserved
Table-41 MAINT2: Maintenance Function Control Register 2
(R/W, Address = 0EH, 2EH)
Symbol
Bit
Default
Description
-
7-6
00
Reserved
TIBLB_L[1:0]
5-4
00
Defines the length of the user-programmable transmit loopback activate/deactivate code contained in TIBLB register. The default selection is 5 bits length.
= 00: 5-bit long activate code in TIBLB [4:0]
= 01: 6-bit long activate code in TIBLB [5:0]
= 10: 7-bit long activate code in TIBLB [6:0]
= 11: 8-bit long activate code in TIBLB [7:0]
RIBLBA_L[1:0]
3-2
00
Defines the length of the user-programmable receive activate loopback code contained in RIBLBA register. The
default selection is 5 bits length.
= 00: 5-bit long activate code in RIBLBA [4:0]
= 01: 6-bit long activate code in RIBLBA [5:0]
= 10: 7-bit long activate code in RIBLBA [6:0]
= 11: 8-bit long activate code in RIBLBA [7:0]
RIBLBD_L[1:0]
1-0
01
Defines the length of the user-programmable receive deactivate loopback code contained in RIBLBD register. The
default selection is 6 bits length.
= 00: 5-bit long deactivate code in RIBLBD [4:0]
= 01: 6-bit long deactivate code in RIBLBD [5:0]
= 10: 7-bit long deactivate code in RIBLBD [6:0]
= 11: 8-bit long deactivate code in RIBLBD [7:0]
Table-42 MAINT3: Maintenance Function Control Register 3
(R/W, Address = 0FH, 2FH)
Symbol
Bit
TIBLB[7:0]
7-0
Default
Description
(000)00001 Defines the user-programmable transmit Inband loopback activate or deactivate code. The default selection is
00001.
TIBLB [7:0] form the 8-bit repeating code
TIBLB [6:0] form the 7-bit repeating code
TIBLB [5:0] form the 6-bit repeating code
TIBLB [4:0] form the 5-bit repeating code
47
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-43 MAINT4: Maintenance Function Control Register 4
(R/W, Address = 10H, 30H)
Symbol
Bit
RIBLBA[7:0]
7-0
Default
Description
(000)00001 Defines the user-programmable receive Inband loopback activate code. The default selection is 00001.
RIBLBA [7:0] form the 8-bit repeating code
RIBLBA [6:0] form the 7-bit repeating code
RIBLBA [5:0] form the 6-bit repeating code
RIBLBA [4:0] form the 5-bit repeating code
Table-44 MAINT5: Maintenance Function Control Register 5
(R/W, Address = 11H, 31H)
Symbol
Bit
RIBLBD[7:0]
7-0
Default
Description
(00)001001 Defines the user-programmable receive Inband loopback deactivate code. The default selection is 001001.
RIBLBD [7:0] form the 8-bit repeating code
RIBLBD [6:0] form the 7-bit repeating code
RIBLBD [5:0] form the 6-bit repeating code
RIBLBD [4:0] form the 5-bit repeating code
Table-45 MAINT6: Maintenance Function Control Register 6
(R/W, Address = 12H, 32H)
Symbol
Bit
Default
Description
-
7
0
Reserved.
BPV_INS
6
0
BPV error insertion
A ‘0’ to ‘1’ transition on this bit will cause a single bipolar violation error to be inserted into the transmit data stream.
This bit must be cleared and set again for a subsequent error to be inserted.
ERR_INS
5
0
PRBS logic error insertion
A ‘0’ to ‘1’ transition on this bit will cause a single PRBS logic error to be inserted into the transmit PRBS data stream.
This bit must be cleared and set again for a subsequent error to be inserted.
EXZ_DEF
4
0
EXZ definition select
= 0: ANSI
= 1: FCC
ERR_SEL
3-2
00
These bits choose which type of error will be counted
= 00: The PRBS logic error is counted by a 16-bit error counter
= 01: The EXZ error is counted by a 16-bit error counter
= 10: The Received CV (BPV) error is counted by a 16-bit error counter
= 11: Both CV (BPV) and EXZ errors are counted by a 16-bit error counter.
CNT_MD
1
0
Counter operation mode select
= 0: Manual Report mode
= 1: Auto Report mode
CNT_TRF
0
0
= 0: Clear this bit for the next ‘0’ to ‘1’ transition on this bit.
= 1: Error counting result is transferred to CNT0 and CNT1 and the error counter is reset.
48
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.7
INTERRUPT CONTROL REGISTERS
Table-46 INTM0: Interrupt Mask Register 0
(R/W, Address = 13H, 33H)
Symbol
Bit
Default
Description
EQ_IM
7
1
Equalizer out of range interrupt mask
= 0: Equalizer out of range interrupt enabled
= 1: Equalizer out of range interrupt masked
IBLBA_IM
6
1
In-band Loopback activate code detect interrupt mask
= 0: In-band Loopback activate code detect interrupt enabled
= 1: In-band Loopback activate code detect interrupt masked
IBLBD_IM
5
1
In-band Loopback deactivate code detect interrupt mask
= 0: In-band Loopback deactivate code detect interrupt enabled
= 1: In-band Loopback deactivate code detect interrupt masked
PRBS_IM
4
1
PRBS synchronic signal detect interrupt mask
= 0: PRBS synchronic signal detect interrupt enabled
= 1: PRBS synchronic signal detect interrupt masked
TCLK_IM
3
1
TCLK loss detect interrupt mask
= 0: TCLK loss detect interrupt enabled
= 1: TCLK loss detect interrupt masked
DF_IM
2
1
Driver Failure interrupt mask
= 0: Driver Failure interrupt enabled
= 1: Driver Failure interrupt masked
AIS_IM
1
1
Alarm Indication Signal interrupt mask
= 0: Alarm Indication Signal interrupt enabled
= 1: Alarm Indication Signal interrupt masked
LOS_IM
0
1
Loss Of Signal interrupt mask
= 0: Loss Of Signal interrupt enabled
= 1: Loss Of Signal interrupt masked
49
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-47 INTM1: Interrupt Masked Register 1
(R/W, Address = 14H, 34H)
Symbol
Bit
Default
DAC_OV_IM
7
1
DAC arithmetic overflow interrupt mask
= 0: DAC arithmetic overflow interrupt enabled
= 1: DAC arithmetic overflow interrupt masked
Description
JAOV_IM
6
1
JA overflow interrupt mask
= 0: JA overflow interrupt enabled
= 1: JA overflow interrupt masked
JAUD_IM
5
1
JA underflow interrupt mask
= 0: JA underflow interrupt enabled
= 1: JA underflow interrupt masked
ERR_IM
4
1
PRBS/QRSS logic error detect interrupt mask
= 0: PRBS/QRSS logic error detect interrupt enabled
= 1: PRBS/QRSS logic error detect interrupt masked
EXZ_IM
3
1
Receive excess zeros interrupt mask
= 0: Receive excess zeros interrupt enabled
= 1: Receive excess zeros interrupt masked
CV_IM
2
1
Receive error interrupt mask
= 0: Receive error interrupt enabled
= 1: Receive error interrupt masked
TIMER_IM
1
1
One-Second Timer expiration interrupt mask
= 0: One-Second Timer expiration interrupt enabled
= 1: One-Second Timer expiration interrupt masked
CNT_IM
0
1
Counter overflow interrupt mask
= 0: Counter overflow interrupt enabled
= 1: Counter overflow interrupt masked
50
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-48 INTES: Interrupt Trigger Edge Select Register
(R/W, Address = 15H, 35H)
Symbol
Bit
Default
Description
EQ_IES
7
0
This bit determines the Equalizer out of range interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the EQ_S bit in the STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the EQ_S bit in the STAT0
status register.
IBLBA_IES
6
0
This bit determines the Inband Loopback Activate Code interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the IBLBA_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the IBLBA_S bit in STAT0
status register
IBLBD_IES
5
0
This bit determines the Inband Loopback Deactivate Code interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the IBLBD_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the IBLBD_S bit in STAT0
status register
PRBS_IES
4
0
This bit determines the PRBS/QRSS synchronization status interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the PRBS_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the PRBS_S bit in STAT0
status register
TCLK_IES
3
0
This bit determines the TCLK Loss interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the TCLK_LOS bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the TCLK_LOS bit in STAT0
status register
DF_IES
2
0
This bit determines the Driver Failure interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the DF_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the DF_S bit in STAT0 status
register
AIS_IES
1
0
This bit determines the AIS interrupt event.
= 0: Interrupt event is generated as a ‘0’ to ‘1’ transition of the AIS_S bit in STAT0 status register
= 1: Interrupt event is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the AIS_S bit in STAT0 status
register
LOS_IES
0
0
This bit determines the LOS interrupt event.
= 0: Interrupt is generated as a ‘0’ to ‘1’ transition of the LOS_S bit in STAT0 status register
= 1: Interrupt is generated as either a ‘0’ to ‘1’ transition or a ‘1’ to ‘0’ transition of the LOS_S bit in STAT0 status
register
51
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.8
LINE STATUS REGISTERS
Table-49 STAT0: Line Status Register 0 (real time status monitor)
(R, Address = 16H, 36H)
Symbol
Bit
Default
Description
EQ_S
7
0
Equalizer status indication
= 0: In range
= 1: Out of range
IBLBA_S
6
0
In-band Loopback activate code receive status indication
= 0: No Inband Loopback activate code is detected
= 1: Activate signal is detected and then received over a period of more than t ms, with a bit error rate less than 102
. The bit remains set as long as the bit error rate does not exceed 10-2.
Note1:
If automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms.
If automatic remote loopback switching is enabled (ARLP = 1), t= 5.1 s. The rising edge of this bit activates the
remote loopback operation in local end.
Note2:
If IBLBA_IM=0:
A ‘0’ to ‘1’ transition on this bit causes an activate code detected interrupt if IBLBA _IES bit is ‘0’;
Any changes of this bit causes an activate code detected interrupt if IBLBA _IES bit is set to ‘1’.
IBLBD_S
5
0
In-band Loopback deactivate code receive status indication
= 0: No Inband Loopback deactivate signal is detected
= 1: The Inband Loopback deactivate signal is detected and then received over a period of more than t, with a bit
error rate less than 10-2. The bit remains set as long as the bit error rate does not exceed 10-2.
Note1:
If automatic remote loopback switching is disabled (ARLP = 0), t = 40 ms.
If automatic remote loopback switching is enabled (ARLP = 1), t = 5.1 s. The rising edge of this bit disables the
remote loopback operation.
Note2:
If IBLBD_IM=0:
A ‘0’ to ‘1’ transition on this bit causes a deactivate code detected interrupt if IBLBD _IES bit is ‘0’;
Any changes of this bit causes a deactivate code detected interrupt if IBLBD _IES bit is set to ‘1’.
PRBS_S
4
0
Synchronous status indication of PRBS/QRSS (real time)
= 0: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS not detected
= 1: 215-1 (E1) PRBS or 220-1 (T1/J1) QRSS detected
Note:
If PRBS_IM=0:
A ‘0’ to ‘1’ transition on this bit causes a synchronous status detected interrupt if PRBS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if PRBS_IES bit is set to ‘1’.
TCLK_LOS
3
0
TCLKn loss indication
= 0: Normal
= 1: TCLK pin has not toggled for more than 70 MCLK cycles
Note:
If TCLK_IM=0:
A ‘0’ to ‘1’ transition on this bit causes an interrupt if TCLK _IES bit is ‘0’.
Any changes of this bit causes an interrupt if TCLK_IES bit is set to ‘1’.
DF_S
2
0
Line driver status indication
= 0: Normal operation
= 1: Line driver short circuit is detected.
Note:
If DF_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if DF _IES bit is ‘0’.
Any changes of this bit causes an interrupt if DF_IES bit is set to ‘1’.
52
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-49 STAT0: Line Status Register 0 (real time status monitor) (Continued)
(R, Address = 16H, 36H)
Symbol
Bit
Default
AIS_S
1
0
Description
Alarm Indication Signal status detection
= 0: No AIS signal is detected in the receive path
= 1: AIS signal is detected in the receive path
Note:
If AIS_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if AIS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if AIS_IES bit is set to ‘1’.
LOS_S
0
0
Loss Of Signal status detection
= 0: Loss of signal on RTIPn/RRINGn is not detected
= 1: Loss of signal on RTIPn/RRINGn is detected.
Note:
If LOS_IM=0
A ‘0’ to ‘1’ transition on this bit causes an interrupt if LOS _IES bit is ‘0’.
Any changes of this bit causes an interrupt if LOS_IES bit is set to ‘1’.
Table-50 STAT1: Line Status Register 1 (real time status monitor)
(R, Address = 17H, 37H)
Symbol
Bit
Default
Description
-
7-6
00
Reserved.
RLP_S
5
0
Indicating the status of Remote Loopback
= 0: The remote loopback is inactive.
= 1: The remote loopback is active (closed).
LATT[4:0]
4-0
00000
Line Attenuation Indication
00000
0 to 2 dB
00001
2 to 4 dB
00010
4 to 6 dB
00011
6 to 8 dB
00100
8 to 10 dB
00101
10 to 12 dB
00110
12 to 14 dB
00111
14 to 16 dB
01000
16 to 18 dB
01001
18 to 20 dB
01010
20 to 22 dB
01011
22 to 24 dB
01100
24 to 26 dB
01101
26 to 28 dB
01110
28 to 30 dB
01111
30 to 32 dB
10000
32 to 34 dB
10001
34 to 36 dB
10010
36 to 38 dB
10011
38 to 40 dB
10100
40 to 42 dB
10101
42 to 44 dB
10110 -11111
>44 dB
53
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
4.2.9
INTERRUPT STATUS REGISTERS
Table-51 INTS0: Interrupt Status Register 0
(R, Address = 18H, 38H) (this register is reset and relevant interrupt request is cleared after a read)
Symbol
Bit
Default
Description
EQ_IS
7
0
This bit indicates the occurrence of Equalizer out of range interrupt event.
= 0: No interrupt event from the Equalizer out of range occurred
= 1: Interrupt event from the Equalizer out of range occurred
IBLBA_IS
6
0
This bit indicates the occurrence of the Inband Loopback Activate Code interrupt event.
= 0: No Inband Loopback Activate Code interrupt event occurred
= 1: Inband Loopback Activate Code interrupt event occurred
IBLBD_IS
5
0
This bit indicates the occurrence of the Inband Loopback Deactivate Code interrupt event.
= 0: No Inband Loopback Deactivate Code interrupt event occurred
= 1: Interrupt event of the received Inband Loopback Deactivate Code occurred.
PRBS_IS
4
0
This bit indicates the occurrence of the interrupt event generated by the PRBS/QRSS synchronization status.
= 0: No PRBS/QRSS synchronization status interrupt event occurred
= 1: PRBS/QRSS synchronization status interrupt event occurred
TCLK_LOS_IS
3
0
This bit indicates the occurrence of the interrupt event generated by the TCLK loss detection.
= 0: No TCLK loss interrupt event.
= 1:TCLK loss interrupt event occurred.
DF_IS
2
0
This bit indicates the occurrence of the interrupt event generated by the Driver Failure.
= 0: No Driver Failure interrupt event occurred
= 1: Driver Failure interrupt event occurred
AIS_IS
1
0
This bit indicates the occurrence of the AIS (Alarm Indication Signal) interrupt event.
= 0: No AIS interrupt event occurred
= 1: AIS interrupt event occurred
LOS_IS
0
0
This bit indicates the occurrence of the LOS (Loss of signal) interrupt event.
= 0: No LOS interrupt event occurred
= 1: LOS interrupt event occurred
54
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-52 INTS1: Interrupt Status Register 1
(R, Address = 19H, 39H) (this register is reset and the relevant interrupt request is cleared after a read)
Symbol
Bit
Default
Description
DAC_OV_IS
7
0
This bit indicates the occurrence of the pulse amplitude overflow of Arbitrary Waveform Generator interrupt event.
= 0: No pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred
= 1: The pulse amplitude overflow of Arbitrary Waveform Generator interrupt event occurred
JAOV_IS
6
0
This bit indicates the occurrence of the Jitter Attenuator Overflow interrupt event.
= 0: No JA Overflow interrupt event occurred
= 1: JA Overflow interrupt event occurred
JAUD_IS
5
0
This bit indicates the occurrence of the Jitter Attenuator Underflow interrupt event.
= 0: No JA Underflow interrupt event occurred
= 1: JA Underflow interrupt event occurred
ERR_IS
4
0
This bit indicates the occurrence of the interrupt event generated by the detected PRBS/QRSS logic error.
= 0: No PRBS/QRSS logic error interrupt event occurred
= 1: PRBS/QRSS logic error interrupt event occurred
EXZ_IS
3
0
This bit indicates the occurrence of the Excessive Zeros interrupt event.
= 0: No Excessive Zeros interrupt event occurred
= 1: EXZ interrupt event occurred
CV_IS
2
0
This bit indicates the occurrence of the Code Violation interrupt event.
= 0: No Code Violation interrupt event occurred
= 1: Code Violation interrupt event occurred
TMOV_IS
1
0
This bit indicates the occurrence of the One-Second Timer Expiration interrupt event.
= 0: No One-Second Timer Expiration interrupt event occurred
= 1: One-Second Timer Expiration interrupt event occurred
CNT_OV_IS
0
0
This bit indicates the occurrence of the Counter Overflow interrupt event.
= 0: No Counter Overflow interrupt event occurred
= 1: Counter Overflow interrupt event occurred
4.2.10 COUNTER REGISTERS
Table-53 CNT0: Error Counter L-byte Register 0
(R, Address = 1AH, 3AH)
Symbol
Bit
Default
CNT_L[7:0]
7-0
00H
Description
This register contains the lower eight bits of the 16-bit error counter. CNT_L[0] is the LSB.
Table-54 CNT1: Error Counter H-byte Register 1
(R, Address = 1BH, 3BH)
Symbol
Bit
Default
CNT_H[7:0]
7-0
00H
Description
This register contains the upper eight bits of the 16-bit error counter. CNT_H[7] is the MSB.
55
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
5
HARDWARE CONTROL PIN SUMMARY
Table-55 Hardware Control Pin Summary
Pin No.
TQFP
Symbol
Description
9
10
MODE1
MODE0
MODE[1:0]: Operation mode of Control interface select (global control)
00= Hardware interface
01= Serial interface
10= Parallel - non-Multiplexed - Motorola Interface
11= Parallel - non-Multiplexed - Intel Interface
13
12
TERM1
TERM2
TERMn: Termination interface select (per channel control)
These pins select internal or external impedance matching for channel n (n=1 or 2)
0 = ternary interface with internal impedance matching network.
1 = ternary interface with external impedance matching network in E1 mode; ternary interface with external impedance matching
network for receiver and ternary interface with internal impedance matching network for transmitter in T1/J1 mode. (External impedance matching is not supported by T1/J1 mode transmitter.)
(This applies to ZB die revision only).
14
15
RXTXM1
RXTXM0
RXTXM[1:0]: Receive and transmit path operation mode select (global control)
00= single rail with HDB3/B8ZS coding
01= single rail with AMI coding
10= dual rail interface with CDR enable
11= slicer mode
54
53
52
51
PULS13
PULS12
PULS11
PULS10
PULSn[3:0]: These pins are used to select the following functions (per channel control):
•
T1/E1/J1 mode (T1/E1/J1 selection of common clock is decided by PULS1n/PULS2n, n=0~3)
•
Transmit pulse template
•
Internal termination impedance (75Ω/100Ω/110Ω/120Ω)
50
49
48
47
PULS23
PULS22
PULS21
PULS20
PULSn[3:0]
T1/E1/J1
TCLK
Cable impedance
(internal matching
impedance)
Cable range or
LBO
Cable loss
0000
E1
2.048 MHz
75Ω
-
0-43 dB
0001
E1
2.048 MHz
120Ω
-
0-43 dB
0010
DSX1
1.544 MHz
100Ω
0-133 ft
0-0.6 dB
0011
DSX1
1.544 MHz
100Ω
133-266 ft
0.6-1.2 dB
0100
DSX1
1.544 MHz
100Ω
266-399 ft
1.2-1.8 dB
0101
DSX1
1.544 MHz
100Ω
399-533 ft
1.8-2.4 dB
0110
DSX1
1.544 MHz
100Ω
533-655 ft
2.4-3.0 dB
0111
J1
1.544 MHz
110Ω
0-655 ft
0-3.0 dB
1000
DS1
1.544 MHz
100Ω
0 dB LBO
0-36 dB
1001
DS1
1.544 MHz
100Ω
-7.5 dB LBO
0-28.5 dB
1010
DS1
1.544 MHz
100Ω
-15.0 dB LBO
0-21 dB
1011
DS1
1.544 MHz
100Ω
-22.5 dB LBO
0-13.5 dB
1100 -1111
DS1
1.544 MHz
100Ω
-
0-13.5 dB
58
60
EQ1
EQ2
EQn: Receive Equalizer on/off control (per channel control)
When the chip is configured by hardware with ternary interface, these pins select Short Haul or Long Haul operation mode for channel n (n=1 or 2)
0= short haul (10dB)
1= long haul (36dB for T1/J1, 43 dB for E1)
57
59
RPD1
RPD2
RPDn: Receiver power down control (per channel control)
0= Normal operation
1= receiver power down
56
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-55 Hardware Control Pin Summary (Continued)
Pin No.
TQFP
Symbol
46
45
PATT11
PATT10
56
55
PATT21
PATT20
16
17
JA1
JA0
19
18
MONT1
MONT2
42
41
LP11
LP10
44
43
LP21
LP20
20
THZ
11
RCLKE
Description
PATTn[1:0]: Transmit test pattern select (per channel control)
In hardware control mode, these pins select the transmit pattern for channel n (n=1 or 2)
00 = normal
01= All Ones
10= PRBS
11= transmitter power down
JA[1:0]: Jitter attenuation position, bandwidth and the depth of FIFO select (global control)
00= JA is disabled
01= JA in receiver, broad bandwidth, FIFO=64 bits
10= JA in receiver, narrow bandwidth, FIFO=128 bits
11= JA in transmitter, narrow bandwidth, FIFO=128 bits
MONTn: Receive Monitor n gain select (per channel control)
In hardware control mode with ternary interface, this pin selects the receive monitor gain for receiver n (n=1 or 2)
0= 0 dB
1= 26 dB
LPn[1:0]: Loopback mode select (per channel control)
When the chip is configured by hardware, these pins are used to select loopback operation modes for channel n (Inband loopback
is not provided in hardware control mode).
00= no loopback
01= analog loopback
10= digital loopback
11= remote loopback
THZ: Transmitter Driver High Impedance Enable (global control)
This signal enables or disables both of the transmitter drivers. A low level on this pin enables both of the two drivers while a high
level on this pin places both of the two drivers in high impedance state.
RCLKE: the active edge of RCLKn select when hardware control mode is used (global control)
0= select the rising edge as active edge of RCLKn
1= select the falling edge as active edge of RCLKn
57
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
IEEE STD 1149.1 JTAG TEST
ACCESS PORT
Clock (TCK) pins. Data is shifted into the registers via the Test Data Input
(TDI) pin, and shifted out of the registers via the Test Data Output (TDO)
pin. Both TDI and TDO are clocked at a rate determined by TCK.
The IDT82V2082 supports the digital Boundary Scan Specification as
described in the IEEE 1149.1 standards.
The JTAG boundary scan registers include BSR (Boundary Scan Register), IDR (Device Identification Register), BR (Bypass Register) and IR
(Instruction Register). These will be described in the following pages. Refer
to Figure-21 for architecture.
The boundary scan architecture consists of data and instruction registers plus a Test Access Port (TAP) controller. Control of the TAP is performed through signals applied to the Test Mode Select (TMS) and Test
Digital output pins
Digital input pins
parallel latched output
BSR (Boundary Scan Register)
MUX
IDR (Device Identification Register)
TDI
BR (Bypass Register)
MUX
6
IR (Instruction Register)
Control<6:0>
TMS
TRST
TAP
(Test Access Port)
Controller
Select
high impedance enable
TCK
Figure-21 JTAG Architecture
58
TDO
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
6.1
INDUSTRIAL
TEMPERATURE RANGES
JTAG INSTRUCTIONS AND INSTRUCTION REGISTER
The IR (Instruction Register) with instruction decode block is used to
select the test to be executed or the data register to be accessed or both.
The instructions are shifted in LSB first to this 3-bit register. See Table56 for details of the codes and the instructions related.
Table-56 Instruction Register Description
IR CODE
INSTRUCTION
COMMENTS
000
Extest
The external test instruction allows testing of the interconnection to other devices. When the current instruction is the EXTEST
instruction, the boundary scan register is placed between TDI and TDO. The signal on the input pins can be sampled by loading the boundary scan register using the Capture-DR state. The sampled values can then be viewed by shifting the boundary
scan register using the Shift-DR state. The signal on the output pins can be controlled by loading patterns shifted in through
input TDI into the boundary scan register using the Update-DR state.
100
Sample / Preload The sample instruction samples all the device inputs and outputs. For this instruction, the boundary scan register is placed
between TDI and TDO. The normal path between IDT82V2082 logic and the I/O pins is maintained. Primary device inputs and
outputs can be sampled by loading the boundary scan register using the Capture-DR state. The sampled values can then be
viewed by shifting the boundary scan register using the Shift-DR state.
110
Idcode
The identification instruction is used to connect the identification register between TDI and TDO. The device's identification
code can then be shifted out using the Shift-DR state.
111
Bypass
The bypass instruction shifts data from input TDI to output TDO with one TCK clock period delay. The instruction is used to
bypass the device.
6.2
JTAG DATA REGISTER
6.2.2
6.2.1
DEVICE IDENTIFICATION REGISTER (IDR)
The BR consists of a single bit. It can provide a serial path between the
TDI input and TDO output, bypassing the BSR to reduce test access times.
The IDR can be set to define the producer number, part number and the
device revision, which can be used to verify the proper version or revision
number that has been used in the system under test. The IDR is 32 bits long
and is partitioned as in Table-57. Data from the IDR is shifted out to TDO
LSB first.
6.2.3
Comments
0
Set to ‘1’
1-11
Producer Number
12-27
Part Number
28-31
Device Revision
BOUNDARY SCAN REGISTER (BSR)
The BSR can apply and read test patterns in parallel to or from all the
digital I/O pins. The BSR is a 98 bits long shift register and is initialized and
read using the instruction EXTEST or SAMPLE/PRELOAD. Each pin is
related to one or more bits in the BSR. For details, please refer to the BSDL
file.
Table-57 Device Identification Register Description
Bit No.
BYPASS REGISTER (BR)
6.2.4
TEST ACCESS PORT CONTROLLER
The TAP controller is a 16-state synchronous state machine. Figure-22
shows its state diagram following the description of each state. Note that
the figure contains two main branches to access either the data or instruction registers. The value shown next to each state transition in this figure
states the value present at TMS at each rising edge of TCK. Please refer
to Table-58 for details of the state description.
59
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
INDUSTRIAL
TEMPERATURE RANGES
Table-58 TAP Controller State Description
STATE
DESCRIPTION
Test Logic Reset
In this state, the test logic is disabled. The device is set to normal operation. During initialization, the device initializes the instruction register
with the IDCODE instruction. Regardless of the original state of the controller, the controller enters the Test-Logic-Reset state when the TMS
input is held high for at least 5 rising edges of TCK. The controller remains in this state while TMS is high. The device processor automatically
enters this state at power-up.
Run-Test/Idle
This is a controller state between scan operations. Once in this state, the controller remains in the state as long as TMS is held low. The
instruction register and all test data registers retain their previous state. When TMS is high and a rising edge is applied to TCK, the controller
moves to the Select-DR state.
Select-DR-Scan
This is a temporary controller state and the instruction does not change in this state. The test data register selected by the current instruction
retains its previous state. If TMS is held low and a rising edge is applied to TCK when in this state, the controller moves into the Capture-DR
state and a scan sequence for the selected test data register is initiated. If TMS is held high and a rising edge applied to TCK, the controller
moves to the Select-IR-Scan state.
Capture-DR
In this state, the Boundary Scan Register captures input pin data if the current instruction is EXTEST or SAMPLE/PRELOAD. The instruction
does not change in this state. The other test data registers, which do not have parallel input, are not changed. When the TAP controller is in
this state and a rising edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or the Shift-DR state if TMS is low.
Shift-DR
In this controller state, the test data register connected between TDI and TDO as a result of the current instruction shifts data on stage toward
its serial output on each rising edge of TCK. The instruction does not change in this state. When the TAP controller is in this state and a rising
edge is applied to TCK, the controller enters the Exit1-DR state if TMS is high or remains in the Shift-DR state if TMS is low.
Exit1-DR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Pause-DR state.
The test data register selected by the current instruction retains its previous value and the instruction does not change during this state.
Pause-DR
The pause state allows the test controller to temporarily halt the shifting of data through the test data register in the serial path between TDI
and TDO. For example, this state could be used to allow the tester to reload its pin memory from disk during application of a long test
sequence. The test data register selected by the current instruction retains its previous value and the instruction does not change during this
state. The controller remains in this state as long as TMS is low. When TMS goes high and a rising edge is applied to TCK, the controller moves
to the Exit2-DR state.
Exit2-DR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-DR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Shift-DR state.
The test data register selected by the current instruction retains its previous value and the instruction does not change during this state.
Update-DR
The Boundary Scan Register is provided with a latched parallel output to prevent changes while data is shifted in response to the EXTEST
and SAMPLE/PRELOAD instructions. When the TAP controller is in this state and the Boundary Scan Register is selected, data is latched
into the parallel output of this register from the shift-register path on the falling edge of TCK. The data held at the latched parallel output
changes only in this state. All shift-register stages in the test data register selected by the current instruction retain their previous value and
the instruction does not change during this state.
Select-IR-Scan
This is a temporary controller state. The test data register selected by the current instruction retains its previous state. If TMS is held low and
a rising edge is applied to TCK when in this state, the controller moves into the Capture-IR state, and a scan sequence for the instruction register is initiated. If TMS is held high and a rising edge is applied to TCK, the controller moves to the Test-Logic-Reset state. The instruction
does not change during this state.
Capture-IR
In this controller state, the shift register contained in the instruction register loads a fixed value of '100' on the rising edge of TCK. This supports
fault-isolation of the board-level serial test data path. Data registers selected by the current instruction retain their value and the instruction
does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-IR
state if TMS is held high, or the Shift-IR state if TMS is held low.
Shift-IR
In this state, the shift register contained in the instruction register is connected between TDI and TDO and shifts data one stage towards its
serial output on each rising edge of TCK. The test data register selected by the current instruction retains its previous value and the instruction
does not change during this state. When the controller is in this state and a rising edge is applied to TCK, the controller enters the Exit1-IR
state if TMS is held high, or remains in the Shift-IR state if TMS is held low.
Exit1-IR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-IR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Pause-IR state.
The test data register selected by the current instruction retains its previous value and the instruction does not change during this state.
Pause-IR
The pause state allows the test controller to temporarily halt the shifting of data through the instruction register. The test data register selected
by the current instruction retains its previous value and the instruction does not change during this state. The controller remains in this state
as long as TMS is low. When TMS goes high and a rising edge is applied to TCK, the controller moves to the Exit2-IR state.
Exit2-IR
This is a temporary state. While in this state, if TMS is held high, a rising edge applied to TCK causes the controller to enter the Update-IR
state, which terminates the scanning process. If TMS is held low and a rising edge is applied to TCK, the controller enters the Shift-IR state.
The test data register selected by the current instruction retains its previous value and the instruction does not change during this state.
60
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-58 TAP Controller State Description (Continued)
STATE
DESCRIPTION
Update-IR
The instruction shifted into the instruction register is latched into the parallel output from the shift-register path on the falling edge of TCK.
When the new instruction has been latched, it becomes the current instruction. The test data registers selected by the current instruction retain
their previous value.
1
Test-logic Reset
0
0
Run Test/Idle
1
Select-DR
1
Select-IR
0
1
0
1
Capture-DR
Capture-IR
0
0
0
0
Shift-DR
Shift-IR
1
1
1
Exit1-DR
1
Exit1-IR
0
0
0
0
Pause-DR
Pause-IR
1
0
1
0
Exit2-DR
Exit2-IR
1
1
Update-DR
1
0
Figure-22 JTAG State Diagram
61
1
Update-IR
1
0
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
7
TEST SPECIFICATIONS
Table-59 Absolute Maximum Rating
Min
Max
Unit
VDDA, VDDD
Symbol
Core Power Supply
-0.5
4.6
V
VDDIO
I/O Power Supply
-0.5
4.6
V
VDDT1-2
Transmit Power Supply
-0.5
4.6
V
VDDR1-2
Receive Power Supply
Vin
Parameter
-0.5
4.6
V
Input Voltage, Any Digital Pin
GND-0.5
5.5
V
Input Voltage, Any RTIPn and RRINGn pin1
GND-0.5
VDDR+0.5
V
ESD Voltage, any pin
2000 2
V
500 3
V
Transient latch-up current, any pin
Iin
Input current, any digital pin
-10
4
DC Input current, any analog pin
4
100
mA
10
mA
±100
mA
Pd
Maximum power dissipation in package
1.23
W
Tc
Case Temperature
120
°C
Ts
Storage Temperature
+150
°C
-65
CAUTION:
Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
1.Reference to ground
2.Human body model
3.Charge device model
4.Constant input current
Table-60 Recommended Operation Conditions
Symbol
Min
Typ
Max
Unit
Core Power Supply
3.13
3.3
3.47
V
VDDIO
I/O Power Supply
3.13
3.3
3.47
V
VDDT
Transmitter Power Supply
3.13
3.3
3.47
V
VDDR
Receive Power Supply
3.13
3.3
3.47
V
TA
Ambient operating temperature
-40
25
85
°C
50% ones density data
100% ones density data
-
100
130
110
140
mA
50% ones density data
100% ones density data
-
110
130
120
140
mA
50% ones density data
100% ones density data
-
120
170
130
180
mA
50% ones density data
100% ones density data
-
100
130
110
140
mA
VDDA,VDDD
Parameter
E1, 75 Ω load
E1, 120 Ω Load
Total current dissipation1,2,3
T1, 100 Ω Load
J1, 110 Ω Load
1.Power consumption includes power consumption on device and load. Digital levels are 10% of the supply rails and digital outputs driving a 50 pF capacitive load.
2.Maximum power consumption over the full operating temperature and power supply voltage range.
3.In short haul mode, if internal impedance matching is chosen, E1 75Ω power dissipation values are measured with template PULS[3:0] = 0000; E1 120Ω power dissipation values are measured
with template PULS[3:0] = 0001; T1 power dissipation values are measured with template PULS[3:0] = 0110; J1 power dissipation values are measured with template PULS[3:0] = 0111.
62
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-61 Power Consumption
Symbol
Parameter
Min
Typ
Max1,2
Unit
50% ones density data:
100% ones density data:
-
330
430
490
mW
50% ones density data:
100% ones density data:
-
370
430
490
mW
50% ones density data:
100% ones density data:
-
400
560
630
mW
50% ones density data:
100% ones density data:
-
330
430
490
mW
E1, 3.3 V, 75 Ω Load
E1, 3.3 V, 120 Ω Load
T1, 3.3 V, 100 Ω Load3
J1, 3.3 V, 110 Ω Load
1.Maximum power and current consumption over the full operating temperature and power supply voltage range. Includes all channels.
2.Power consumption includes power absorbed by line load and external transmitter components.
3.T1 is measured with maximum cable length.
Table-62 DC Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
-
-
0.8
V
2.0
-
-
V
-
0.4
V
-
VDDIO
V
VIL
Input Low Level Voltage
VIH
Input High Voltage
VOL
Output Low level Voltage (Iout=1.6mA)
2.4
VOH
Output High level Voltage (Iout=400µA)
VMA
Analog Input Quiescent Voltage (RTIPn, RRINGn
pin while floating)
II
Input Leakage Current
TMS, TDI, TRST
All other digital input pins
-10
50
10
µA
µA
IZL
High Impedance Leakage Current
-10
10
µA
1.5
V
Ci
Input capacitance
15
pF
Co
Output load capacitance
50
pF
Co
Output load capacitance (bus pins)
100
pF
63
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-63 E1 Receiver Electrical Characteristics
Symbol
Parameter
Min
Typ
Receiver sensitivity
Short haul with cable loss@1024kHz:
Long haul with cable loss@1024kHz:
Analog LOS level
Short haul
Long haul
RPD
dB
Test conditions
mVp-p
dB
A LOS level is programmable for Long Haul
% ones
G.775, ETSI 300 233
32
2048
12.5
JA enabled
0.05
U.I.
Input Jitter Tolerance
1 Hz – 20 Hz
20 Hz – 2.4 KHz
18 KHz – 100 KHz
37
5
2
U.I.
U.I.
U.I.
G.823, with 6 dB cable attenuation
Receiver Differential Input Impedance
20
KΩ
Internal mode
dB
dB
dB
G.703 Internal termination
U.I.
U.I.
JA disabled
Input termination resistor tolerance
RRX
-10
-43
-48
Receive Intrinsic Jitter
20Hz - 100kHz
ZDM
Unit
800
-4
Allowable consecutive zeros before LOS
G.775:
I.431/ETSI300233:
LOS reset
Max
Receive Return Loss
51 KHz – 102 KHz
102 KHz - 2.048 MHz
2.048 MHz – 3.072 MHz
±1%
20
20
20
Receive path delay
Single rail
Dual rail
7
2
64
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-64 T1/J1 Receiver Electrical Characteristics
Symbol
Parameter
Min
Typ
receiver sensitivity
Short haul with cable loss@772kHz:
Long haul with cable loss@772kHz:
Analog LOS level
Short haul
Long haul
ZDM
Receiver Differential Input Impedance
RPD
Receive Return Loss
39 KHz – 77 KHz
77 KHz - 1.544 MHz
1.544 MHz – 2.316 MHz
dB
Test conditions
mVp-p
dB
A LOS level is programmable for Long Haul
% ones
G.775, ETSI 300 233
175
1544
12.5
JA enabled ( in receive path)
0.02
0.025
0.025
0.050
138.0
28.0
0.4
20
Input termination resistor tolerance
RRX
-10
-36
-48
Receive Intrinsic Jitter
10 Hz - 8 kHz
10 Hz - 40 kHz
8 kHz - 40 kHz
Wide band
Input Jitter Tolerance
0.1 Hz – 1 Hz
4.9 Hz – 300 Hz
10 KHz – 100 KHz
Unit
800
-4
Allowable consecutive zeros before LOS
T1.231-1993
I.431
LOS reset
Max
U.I.
U.I.
U.I.
U.I.
U.I.
U.I.
U.I.
AT&T62411
KΩ
Internal mode
dB
dB
dB
G.703
Internal termination
±1%
20
20
20
Receive path delay
Single rail
Dual rail
JA disabled
7
2
65
U.I.
U.I.
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-65 E1 Transmitter Electrical Characteristics
Symbol
Vo-p
Vo-s
Parameter
Output pulse amplitudes
E1, 75Ω load
E1, 120Ω load
Zero (space) level
E1, 75Ω load
E1, 120Ω load
Min
Typ
Max
Unit
2.14
2.7
2.37
3.0
2.60
3.3
V
V
0.237
0.3
V
V
-0.237
-0.3
Transmit amplitude variation with supply
-1
Difference between pulse sequences for 17 consecutive pulses (T1.102)
Tpw
RTX
Isc
256
ns
Output Pulse Width at 50% of nominal amplitude
232
0.95
1.05
Ratio of the width of Positive and Negative Pulses at the center of the pulse interval (G.703)
0.95
1.05
Transmit Return Loss (G.703)
20
15
12
dB
dB
dB
Intrinsic Transmit Jitter (TCLK is jitter free)
20 Hz – 100 KHz
Td
%
mV
Ratio of the amplitudes of Positive and Negative Pulses at the center of the pulse interval
(G.703)
51 KHz – 102 KHz
102 KHz - 2.048 MHz
2.048 MHz – 3.072 MHz
JTXp-p
244
+1
200
0.050
U.I.
Transmit path delay (JA is disabled)
Single rail
Dual rail
8.5
4.5
U.I.
U.I.
Line short circuit current
100
mA
66
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-66 T1/J1 Transmitter Electrical Characteristics
Symbol
Parameter
Vo-p
Output pulse amplitudes
Vo-s
Zero (space) level
Min
Typ
2.4
3.0
-0.15
Transmit amplitude variation with supply
-1
Difference between pulse sequences for 17 consecutive pulses
(T1.102)
TPW
Output Pulse Width at 50% of nominal amplitude
338
350
Pulse width variation at the half amplitude (T1.102)
Imbalance between Positive and Negative Pulses amplitude
(T1.102)
Output power level (T1.102)
@772kHz
@1544kHz (referenced to power at 772kHz)
RTX
ISC
3.6
V
0.15
V
+1
%
200
mV
362
ns
20
ns
0.95
1.05
12.6
-29
17.9
20
15
12
dBm
dBm
dB
dB
dB
Intrinsic Transmit Jitter (TCLK is jitter free)
10 Hz – 8 KHz
8 KHz – 40 KHz
10 Hz – 40 KHz
wide band
Td
Unit
Transmit Return Loss
39 KHz – 77 KHz
77 KHz – 1.544 MHz
1.544 MHz – 2.316 MHz
JTXP-P
Max
0.020
0.025
0.025
0.050
U.I.p-p
U.I.p-p
U.I.p-p
U.I.p-p
Transmit path delay (JA is disabled)
Single rail
Dual rail
8.5
4.5
U.I.
U.I.
Line short circuit current
100
mA
67
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-67 Transmitter and Receiver Timing Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
MCLK frequency
E1:
T1/J1:
2.048
1.544
MHz
MCLK tolerance
-100
100
ppm
MCLK duty cycle
30
70
%
Transmit path
TCLK frequency
E1:
T1/J1:
2.048
1.544
MHz
TCLK tolerance
-50
+50
ppm
TCLK Duty Cycle
10
90
%
t1
Transmit Data Setup Time
40
ns
t2
Transmit Data Hold Time
40
ns
Delay time of THZ low to driver high impedance
10
Delay time of TCLK low to driver high impedance
us
75
U.I.
± 80
ppm
Receive path
Clock recovery capture E1
range 1
T1/J1
± 180
RCLK duty cycle 2
t4
60
%
457
607
488
648
519
689
ns
203
259
244
324
285
389
ns
203
259
244
324
285
389
ns
20
ns
RCLK pulse width low time
E1:
T1/J1:
t6
50
RCLK pulse width 2
E1:
T1/J1:
t5
40
RCLK pulse width high time
E1:
T1/J1:
Rise/fall time 3
t7
Receive Data Setup Time
E1:
T1/J1:
t8
200
200
244
324
ns
200
200
244
324
ns
Receive Data Hold Time
E1:
T1/J1:
1.Relative to nominal frequency, MCLK= ± 100 ppm
2.RCLK duty cycle widths will vary depending on extent of received pulse jitter displacement. Maximum and minimum RCLK duty cycles are for worst case jitter conditions (0.2UI displacement
for E1 per ITU G.823).
3.For all digital outputs. C load = 15pF
68
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
TCLKn
t1
t2
TDn/TDPn
TDNn
Figure-23 Transmit System Interface Timing
t4
RCLKn
t6
t5
t7
t8
RDPn/RDn
(RCLK_SEL = 0 software mode)
(RCLKE = 0 hardware mode)
RDNn/CVn
t7
t8
RDPn/RDn
(RCLK_SEL = 1 software mode)
(RCLKE = 1 hardware mode)
RDNn/CVn
Figure-24 Receive System Interface Timing
Table-68 Jitter Tolerance
Jitter Tolerance
E1: 1 Hz
20 Hz – 2.4 KHz
18 KHz – 100 KHz
T1/J1: 1 Hz
4.9 Hz – 300 Hz
10 KHz – 100 KHz
Min
Typ
Unit
Standard
37
1.5
0.2
U.I.
U.I.
U.I.
G.823
Cable attenuation is 6dB
138.0
28.0
0.4
U.I.
U.I.
U.I.
AT&T 62411
69
Max
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Figure-25 E1 Jitter Tolerance Performance
Figure-26 T1/J1 Jitter Tolerance Performance
70
INDUSTRIAL
TEMPERATURE RANGES
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-69 Jitter Attenuator Characteristics
Parameter
Min
Typ
Max
Unit
Jitter Transfer Function Corner (-3dB) Frequency
E1, 32/64/128 bits FIFO
JABW = 0:
JABW = 1:
T1/J1, 32/64/128 bits FIFO
JABW = 0:
JABW = 1:
6.8
0.9
Hz
Hz
5
1.25
Hz
Hz
Jitter Attenuator
E1: (G.736)
@ 3 Hz
@ 40 Hz
@ 400 Hz
@ 100 kHz
T1/J1: (Per AT&T pub.62411)
@ 1 Hz
@ 20 Hz
@ 1 kHz
@ 1.4 kHz
@ 70 kHz
-0.5
-0.5
+19.5
+19.5
dB
0
0
+33.3
40
40
Jitter Attenuator Latency Delay
32 bits FIFO:
64 bits FIFO:
128 bits FIFO:
16
32
64
U.I.
U.I.
U.I.
Input jitter tolerance before FIFO overflow or underflow
32 bits FIFO:
64 bits FIFO:
128 bits FIFO:
28
58
120
U.I.
U.I.
U.I.
71
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Figure-27 E1 Jitter Transfer Performance
Figure-28 T1/J1 Jitter Transfer Performance
72
INDUSTRIAL
TEMPERATURE RANGES
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-70 JTAG Timing Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
t1
TCK Period
100
ns
t2
TMS to TCK setup Time
TDI to TCK Setup Time
25
ns
t3
TCK to TMS Hold Time
TCK to TDI Hold Time
25
ns
t4
TCK to TDO Delay Time
50
t1
TCK
t2
t3
TMS
TDI
t4
TDO
Figure-29 JTAG Interface Timing
73
ns
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
8
MICROCONTROLLER INTERFACE TIMING CHARACTERISTICS
8.1
SERIAL INTERFACE TIMING
Table-71 Serial Interface Timing Characteristics
Symbol
Parameter
Min
Typ
Max
Unit
t1
SCLK High Time
100
t2
SCLK Low Time
100
ns
t3
Active CS to SCLK Setup Time
5
ns
t4
Last SCLK Hold Time to Inactive CS Time
41
ns
t5
CS Idle Time
41
ns
t6
SDI to SCLK Setup Time
0
ns
t7
SCLK to SDI Hold Time
82
ns
t10
SCLK to SDO Valid Delay Time
95
ns
t11
Inactive CS to SDO High Impedance Hold Time
90
ns
Comments
ns
CS
t3
t1
t4
t2
t5
SCLK
t6
SDI
t7
t7
LSB
MSB
LSB
Figure-30 Serial Interface Write Timing
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SCLK
t4
t10
CS
SDO
0
1
2
3
4
5
6
t11
7
13
14
15
16
Figure-31 Serial Interface Read Timing with SCLKE=1
1
2
3
4
5
6
7
8
9
10
11
12
SCLK
t4
t10
CS
SDO
0
1
2
3
Figure-32 Serial Interface Read Timing with SCLKE=0
74
4
5
6
t11
7
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
8.2
PARALLEL INTERFACE TIMING
Table-72 Non-Multiplexed Motorola Read Timing Characteristics
Symbol
Parameter
Min
tRC
Read Cycle Time
190
180
tDW
Valid DS Width
tRWV
Delay from DS to Valid Read Signal
tRWH
R/W to DS Hold Time
tAV
ns
15
ns
15
ns
65
Address to DS Hold Time
tPRD
DS to Valid Read Data Propagation Delay
tDAZ
Delay from DS inactive to data bus High Impedance
5
Recovery Time from Read Cycle
5
ns
65
ns
175
ns
20
ns
ns
tRC
tRecovery
tDW
DS+CS
tRWH
tRWV
R/W
tADH
tAV
A[x:0]
Valid Address
tDAZ
tPRD
READ D[7:0]
Valid Data
Figure-33 Non-Multiplexed Motorola Read Timing
75
Unit
ns
Delay from DS to Valid Address
tADH
tRecovery
Max
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-73 Non-Multiplexed Motorola Write Timing Characteristics
Symbol
Parameter
Min
tWC
Write Cycle Time
120
100
tDW
Valid DS Width
tRWV
Delay from DS to Valid Write Signal
tRWH
R/W to DS Hold Time
tAV
Delay from DS to Valid Address
tAH
Address to DS Hold Time
tDV
Delay from DS to Valid Write Data
tDHW
tRecovery
Max
Unit
ns
ns
15
ns
15
ns
15
ns
65
ns
65
ns
Write Data to DS Hold Time
65
ns
Recovery Time from Write Cycle
5
ns
tWC
tRecovery
tDW
DS+CS
tRWH
tRWV
R/W
tAV
A[x:0]
tAH
Valid Address
tDV
tDHW
Valid Data
Write D[7:0]
Figure-34 Non-Multiplexed Motorola Write Timing
76
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-74 Non-Multiplexed Intel Read Timing Characteristics
Symbol
tRC
tRDW
Parameter
Min
Read Cycle Time
190
Valid RD Width
180
tAV
Delay from RD to Valid Address
tAH
Address to RD Hold Time
tPRD
RD to Valid Read Data Propagation Delay
tDAZ
Delay from RD inactive to data bus High Impedance
5
Recovery Time from Read Cycle
5
tRecovery
Max
ns
ns
15
ns
175
ns
20
ns
65
ns
ns
tRC
tRecovery
tRDW
CS+RD
tAH
tAV
A[x:0]
Valid Address
tDAZ
tPRD
Valid Data
READ D[7:0]
Note: WR should be tied to high
Figure-35 Non-Multiplexed Intel Read Timing
77
Unit
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
Table-75 Non-Multiplexed Intel Write Timing Characteristics
Symbol
Parameter
Min
tWC
Write Cycle Time
120
tWRW
Valid WR Width
100
tAV
Delay from WR to Valid Address
tAH
Address to WR Hold Time
tDV
Delay from WR to Valid Write Data
tDHW
tRecovery
Max
Unit
ns
ns
15
ns
15
ns
65
ns
Write Data to WR Hold Time
65
ns
Recovery Time from Write Cycle
5
ns
tRecovery
tWC
tWRW
WR+ CS
tAH
tAV
A[x:0]
Valid Address
tDHW
tDV
Write D[7:0]
Valid Data
Note: RD should be tied to high
Figure-36 Non-Multiplexed Intel Write Timing
78
INDUSTRIAL
TEMPERATURE RANGES
DUAL CHANNEL T1/E1/J1 LONG HAUL/SHORT HAUL LINE INTERFACE UNIT
ORDERING INFORMATION
IDT
XXXXXXX
Device Type
XX
X
Process/
Temperature
Range
Blank
Industrial (-40 °C to +85 °C)
PF
Thin Quad Flatpack (TQFP, PN80)
82V2082
Long Haul/Short Haul LIU
DATASHEET DOCUMENT HISTORY
08/26/2003 pgs. 19, 20, 21,22, 33, 37, 45, 63, 64
04/09/2004 pgs. 14, 22, 24, 56
07/19/2004 pgs. 34, 66, 67
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com*
for Tech Support:
408-330-1552
email:[email protected]
To search for sales office near you, please click the sales button found on our home page or dial the 800# above and press 2.
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
79