Impala Linear Corporation ILC7010 Preliminary 80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator General Description Features The ILC7010 is an 80mA, Ultra Low Noise, Low Dropout (LDO) linear regulator, designed and processed in Impala’s proprietary CMOS process technology. This process combines the best CMOS features of low quiescent current, small size and low dropout voltage with the best bipolar features of high ripple rejection, ultra low noise and power handling capability. The ILC7010 offers a quiescent current of less than 100mA, a logic level enable (regulator on/off) pin, a footprint that is half the size of the industry standard SOT-23, and a low dropout voltage of 50mV at 10mA. With better than 70dB (1kHz) of ripple rejection, ultra low noise of 20µVRMS and 1% output voltage accuracy, the ILC7010 sets a new standard in linear regulators for communications and personal electronics applications. The ILC7010 is designed to operate with small, low cost ceramic capacitors and is stable over a wide range of ESR values. In addition to the output capacitor, the ILC7010 requires only a 1µF input capacitor. The enable pin can be tied to VIN for easy device layout. The ILC7010 is available in a number of fixed output voltages ranging from 2.5V to 8V. An adjustable version will be available shortly. For competitive replacements, the ILC7080 is available in a variety of pinout options in a SOT-23 package. The ILC7080 offers the same operating characteristics and features as the ILC7010 • 1% output voltage accuracy • Only 20µVRMS noise @ 10kHz • Uses low ESR ceramic or tantalum output capacitor to minimize noise and output ripple • Only 90µA ground current at 80mA load • Ripple rejection up to 70dB at 1kHz, 60dB at 1MHz • Excellent line and transient response • Guaranteed to 80mA output current • Industry standard five lead SC70 packages • Fixed 2.8V, 3.0V, 3.3V, 3.6V, 4.7V, 5.0V and adjustable output voltage options • Metal mask option available for custom voltages between 2.5V and 10V Applications • • • • Cellular phones Wireless communicators PDAs / palmtops / organizers Battery powered portable electronics The ILC7010 is ideally suited for use in small size cordless and cellular handsets as well as many other low battery powered electronic devices. Please contact Impala for samples and application information. TYPICAL CIRCUIT VIN 4 5 CIN ILC7010 1 ON 2 VOUT (TA = 0OC TO 70 OC) COUT 80mA, fixed voltage, SC-70 Package Note: Fixed voltage options are defined by 2-digit code as shown in the package markings information section of the data sheet. N/C Impala Linear Corporation ILC7010-C5-XX 3 OFF ILC7010 1.3 Ordering Information (408) 574-3939 www.impalalinear.com August 2000 1 80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary Pin Description ILC7010 (fixed voltage veresion) Pin Description Pin Name Pin Description 1 ON/OFF 2 N/C 3 GND Ground pin. Local ground for COUT 4 VOUT Output voltage. Connect COUT between this pin and the GND (pin 3) 5 VIN Shutdown Connect Directly to Supply PIN PACKAGE CONFIGURATIONS VIN VOUT 5 4 ILC7010 ON 1 OFF Parameter 2 N/C 3 GND Symbol Ratings Units VIN -0.3 to +9V V VON/OFF -0.3 to VIN V Output Current IOUT Short Circuit Protected mA Output Voltage VOUT -0.3 to VIN +0.3 V PD TBD mW TJ(MAX) -40 to +125 °C TSTG -40 to +125 °C TA -40 to +85 °C Input voltage 7010 ON/OFF Input Voltage Package Power Dissipation Maximim Junction Temp. Range Storage Temperature Operation Ambient Temperature Impala Linear Corporation ILC7010 1.3 (408) 574-3939 www.impalalinear.com August 2000 2 80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary ELECTRICAL CHARACTERISTICS ILC7010 Unless otherwise specified, all limits are at TA=25°C, VIN = VOUT(NOM) + 1v, IOUT = 1mA, COUT = 1µF, VON/OFF = 2V Parameter Input Voltage Range Output Voltage Accuracy Symbol Conditions VIN ∆VOUT/(VOUT*∆VIN) Line Regulation Dropout Voltage (Note 3) Ground Pin Current VOUT (NOM +1V < 8V) VIN VOUT IGND Typ Units 2.5-8 V ±1 % 0.007 %/V IOUT = 10µA 0.1 IOUT = 10mA 50 IOUT = 20mA IOUT = 80mA 70 235 IOUT = 0mA 66 IOUT = 10mA 67 IOUT = 80mA 90 µA mV µA Shutdown (OFF) Current ION/OFF ION/OFF = 0V ON/OFF Input Voltage VON/OFF High = Regulator On Low = Regulator Off ON/OFF Pin Input Current (Note 5) IIN ON/OFF VON/OFF 0.6V Regulator OFF VON/OFF 2V Regulator ON 0.1 1.5-2.0 0.6 0.3 1 VOUT > 0.95VOUT (NOM), tpw = 2ms 100-120 mA BW = 300Hz to 50kHz, CIN = 1µF CNOISE = 0.01µF, COUT = 2.2µF, IOUT = 10mA TBD µVRMS 70 50 65 dB 14 mV 40 200 mV 1.5 kΩ Peak Output Current (Note 4) IIN (peak) Output Noise Voltage (RMS) eN Ripple Rejection ∆VOUT/∆VIN COUT = 4.7µF IOUT = 100mA Dynamic Line Regulation ∆VOUT (line) VIN: VOUT (NOM) + 1V to VOUT (NOM) + 2V, tr/tf = 2µs; IOUT = 80mA Dynamic Load Regulation ∆VOUT(load) IOUT: 1mA to 80mA; tr < 5mS Short Circuit Current ISC VOUT = 0V Resistance Shutdown Discharge Freq = 1kHz Freq = 10kHz Freq = 1MHz V µA mA Note 1: Absolute maximum ratings indicate limits which when exceeded may result in damage to the component. Electrical specifications do not apply when operating the device outside of its rated operating conditions. Note 2: Specified Min/Max limits are production tested or guaranteed through correlation based on statistical control methods. Measurements are taken at constant junction temperature as close to ambient as possible using low duty pulse testing. Note 3: Dropout voltage is defined as the input to output differential voltage at which the output voltage drops 2% below the nominal value measured with a 1V differential. Note 4: Guaranteed by design Note 5: The device’s shutdown pin includes a 2MΩ internal pull down resistor connected to ground. Impala Linear Corporation ILC7010 1.3 (408) 574-3939 www.impalalinear.com August 2000 3 80mA SC70 Ultra Low Noise CMOS RF-LDO™ Regulator Preliminary SC-70 Package Markings ILC7010C5-xx Output Voltage (V) Grade Order Information Supplied As: 2.8 A ILC7010C5-28 3K Units on Tape and Reel 3.0 A ILC7010C5-30 3K Units on Tape and Reel 3.3 A ILC7010C5-33 3K Units on Tape and Reel 3.6 A ILC7010C5-36 3K Units on Tape and Reel 4.7 A ILC7010C5-47 3K Units on Tape and Reel 5.0 A ILC7010C5-50 3K Units on Tape and Reel *NOTE: First two characters identify the product and the last two characters identify the datecode. .45 .70 .325 1.85 c 1.15/1.35 .325 .65 1.30 Recommended Mount Pad 0.15-0.30 0.65 BSC .65 0.65 BSC 1. 2. 3. 4. 0.45-0.60 0.10-0.18 x 0.02 0.80-1.00 0.78-0.98 1.80-2.20 1.30 15° All dimensions are in millimeters min/max Dimensions are inclusive of plating Dimensions are exclusive of mold flash and metal burr All specifications comply to EIAJ SC70 Devices sold by Impala Linear Corporation are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Impala Linear Corporation makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Impala Linear Corporation makes no warranty of merchantability or fitness for any purpose. Impala Linear Corporation reserves the right to discontinue production and change specifications and prices at any time and without notice. This product is intended for use in normal commercial applications. Applications requiring an extended temperature range, unusual environmental requirements, or high reliability applications, such as military and aerospace, are specifically not recommended without additional processing by Impala Linear Corporation. Life Support Policy Impala Linear Corporation’s products are not authorized for use as critical components in life support devices or systems. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labelling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonbly expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Impala Linear Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in an Impala Linear Corporation product. No other circuits, patents, licenses are implied. Impala Linear Corporation ILC7010 1.3 (408) 574-3939 www.impalalinear.com August 2000 4