SEME-LAB IP137MAE

IP137MAHVE
IP137MHVE
MECHANICAL DATA
Dimensions in mm (inches)
9.14 (0.360)
8.64 (0.340)
1.27 (0.050)
1.07 (0.040)
≈ 2.16 (0.085)
12 13 14 15 16
IP137MAE
IP137MEA
0.5 AMP
NEGATIVE ADJUSTABLE
VOLTAGE REGULATOR
IN CERAMIC SURFACE
MOUNT PACKAGE
1.39 (0.055)
1.02 (0.040)
7.62 (0.300)
7.12 (0.280)
11
17
10
18
9
1
FEATURES
0.76 (0.030)
0.51 (0.020)
2
8
7
6
1.39 (0.055)
1.15 (0.045)
5
4
3
1.65 (0.065)
1.40 (0.055)
0.33 (0.013)
Rad.
0.08 (0.003)
0.43 (0.017)
0.18 (0.007 Rad.
• –1.2V TO 47V OUTPUT VOLTAGE RANGE
• 0.5A OUTPUT CURRENT
• 1% OUTPUT VOLTAGE TOLERANCE
• 0.5% / A LOAD REGULATION
• 0.01% / V LINE REGULATION
LCC4 CERAMIC SURFACE MOUNT
• 0.02% / W THERMAL REGULATION
• INTERNAL PROTECTION
Pads 4,5
– Adjust
Pads 6,7,8,9,10,11,12,13 – VOUT
Pads 15,16,17,18,1,2
– VIN
Internal current and power limiting coupled with
true thermal limiting prevents device damage
due to overloads or shorts, even if the regulator
is not fastened to a heat sink.
ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated)
VI–O
Input - Output Differential Voltage
– Standard
40V
– HV Series
50V
IO
Output Current
Internally limited
PD
Power Dissipation
Internally limited
TJ
Operating Junction Temperature Range
–55 to +150°C
TSTG
Storage Temperature
–65 to 150°C
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 2830
Issue 2
IP137MAHVE
IP137MHVE
Parameter
IP137MAHV
IP137MA
Min.
Typ.
Max.
Test Conditions
IOUT = 10mA
VREF
Reference Voltage
ΔVIN
Line Regulation 1
ΔIOUT
Load Regulation 1
Thermal Regulation
Ripple Rejection
IADJ
ΔIADJ
Adjust Pin Current
Adjust Pin Current
Change
Minimum Load
Current
ICL
Current Limit
ΔTEMP Stability
ΔVOUT
ΔTIME
en
RθJC
Long Term Stability
V
-1.220
-1.25
-1.280 -1.200
-1.25
-1.300
V
0.005
0.010
0.010
0.020
0.010
0.030
0.020
0.050
VOUT ≤ 5V
5
25
15
25
mV
VOUT ≥ 5V
0.1
0.5
0.3
0.5
%
IOUT = 10mA to IMAX
VOUT ≤ 5V
10
50
20
50
mV
TJ = -55 to 150°C
VOUT ≥ 5V
0.2
1
0.3
1
%
tp = 10ms
TA = 25°C
0.002
0.020
0.002
0.02
%/W
IOUT = 10mA to IMAX
VIN – VOUT = 3V to VMAX
TJ = -55 to 150°C
VIN – VOUT = 3V to VMAX
TJ = -55 to 150°C
VOUT = -10V
f = 120Hz
CADJ = 0
CADJ = 10μF
TJ = -55 to 150°C
60
66
70
80
TJ = -55 to 150°C
TJ = -55 to +150°C
TJ = -55 to 150°C
TJ = -55 to 150°C
TJ = -55 to 150°C
TA = +125°C
t = 1000 Hrs
f = 10 Hz to 10 kHz
(% of VOUT)
TA = 25°C
Junction to Case
Units
-1.275
RMS Output Noise
Thermal Resistance
Max.
-1.25
66
dB
77
dB
100
65
100
IOUT = 10mA to IMAX
0.2
2
0.5
5
VIN – VOUT = 3V to 40V
1.0
5
2
5
2.0
6
3
6
VIN – VOUT ≤ 40V
2.5
5
2.5
5
VIN – VOUT ≤ 10V
1.2
3
1.2
3
1.5
0.50
0.80
1.5
0.15
0.17
0.10
0.17
VIN – VOUT = 3V to 50V
VIN – VOUT ≤ 15V
0.50
0.80
VIN – VOUT = 40V
0.15
0.17
0.10
0.17
0.5
0.6
1.5
0.6
0.3
1
0.3
VIN – VOUT = 50V
LCC4 Package
13
μA
μA
mA
A
0.5
%
1
%
%
0.003
0.003
%/V
60
65
(HV SERIES)
ΔVOUT Temperature
Typ.
-1.262 -1.225
(HV SERIES)
IMIN
Min.
-1.25
IOUT = 10mA to IMAX
ΔVOUT
IP137MHV , IP137M
-1.238
P ≤ PMAX
ΔVOUT
IP137MAE
IP137MEA
13
°C/W
1) Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to
heating effects are covered under thermal regulation specifications.
2) Test Conditions unless otherwise stated: VIN – VOUT = 5V , IOUT = 0.1A , PMAX = 10W, IMAX = 0.5A
VMAX = 40V for standard series , 50V for HV series.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 2830
Issue 2