IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® 128K x 32, 128K x 36, and 256K x 18 4Mb, PIPELINE 'NO WAIT' STATE BUS SRAM PRELIMINARY INFORMATION SEPTEMBER 2005 FEATURES DESCRIPTION • 100 percent bus utilization The 4 Meg 'NLP/NVP' product family feature high-speed, low-power synchronous static RAMs designed to provide a burstable, high-performance, 'no wait' state, device for networking and communications applications. They are organized as 128K words by 32 bits, 128K words by 36 bits, and 256K words by 18 bits, fabricated with ISSI's advanced CMOS technology. • No wait cycles between Read and Write • Internal self-timed write cycle • Individual Byte Write Control • Single R/W (Read/Write) control pin • Clock controlled, registered address, data and control • Interleaved or linear burst sequence control using MODE input • Three chip enables for simple depth expansion and address pipelining • Power Down mode • Common data inputs and data outputs • CKE pin to enable clock and suspend operation • JEDEC 100-pin TQFP, 165-ball PBGA and 119ball PBGA packages • Power supply: NVP: VDD 2.5V (± 5%), VDDQ 2.5V (± 5%) NLP: VDD 3.3V (± 5%), VDDQ 3.3V/2.5V (± 5%) • Industrial temperature available Incorporating a 'no wait' state feature, wait cycles are eliminated when the bus switches from read to write, or write to read. This device integrates a 2-bit burst counter, high-speed SRAM core, and high-drive capability outputs into a single monolithic circuit. All synchronous inputs pass through registers are controlled by a positive-edge-triggered single clock input. Operations may be suspended and all synchronous inputs ignored when Clock Enable, CKE is HIGH. In this state the internal device will hold their previous values. All Read, Write and Deselect cycles are initiated by the ADV input. When the ADV is HIGH the internal burst counter is incremented. New external addresses can be loaded when ADV is LOW. Write cycles are internally self-timed and are initiated by the rising edge of the clock inputs and when WE is LOW. Separate byte enables allow individual bytes to be written. A burst mode pin (MODE) defines the order of the burst sequence. When tied HIGH, the interleaved burst sequence is selected. When tied LOW, the linear burst sequence is selected. • Lead-free available FAST ACCESS TIME Symbol tKQ tKC Parameter Clock Access Time Cycle Time Frequency -250 2.6 4 250 -200 3.1 5 200 Units ns ns MHz Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 1 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® BLOCK DIAGRAM x 32/x 36: A [0:16] or x 18: A [0:17] ADDRESS REGISTER MODE A0-A1 CLK CONTROL LOGIC K CKE 128Kx32; 128Kx36; 256Kx18 MEMORY ARRAY A2-A16 or A2-A17 WRITE ADDRESS REGISTER BURST ADDRESS COUNTER A'0-A'1 WRITE ADDRESS REGISTER K DATA-IN REGISTER K DATA-IN REGISTER CE CE2 CE2 ADV WE BWŸX } CONTROL REGISTER K CONTROL LOGIC (X=a,b,c,d or a,b) OUTPUT REGISTER BUFFER OE ZZ 32, 36 or 18 DQx/DQPx 2 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® Bottom View 165-Ball, 13 mm x 15mm BGA 1 mm Ball Pitch, 11 x 15 Ball Array Bottom View 119-Ball, 14 mm x 22 mm BGA 1 mm Ball Pitch, 7 x 17 Ball Array Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 3 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® PIN CONFIGURATION — 128K X 36, 165-Ball PBGA (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 11 A NC A CE BWc BWb CE2 CKE ADV NC A NC B NC A CE2 BWd BWa CLK WE OE NC A NC C DQPc NC VDDQ VSS VSS VSS VSS VSS VDDQ NC DQPb D DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb E DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb F DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb G DQc DQc VDDQ VDD VSS VSS VSS VDD VDDQ DQb DQb H NC NC NC VDD VSS VSS VSS VDD NC NC ZZ J DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa K DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa L DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa M DQd DQd VDDQ VDD VSS VSS VSS VDD VDDQ DQa DQa N DQPd NC VDDQ VSS NC NC NC VSS VDDQ NC DQPa P NC NC A A NC A1* NC A A A NC R MODE NC A A NC A0* NC A A A A Note: A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired. PIN DESCRIPTIONS Symbol Pin Name MODE Burst Sequence Selection A Address Inputs VDD 3.3V/2.5V Power Supply A0, A1 Synchronous Burst Address Inputs NC No Connect ADV Synchronous Burst Address Advance/ Load DQx Data Inputs/Outputs DQPx Parity Data I/O WE Synchronous Read/Write Control Input VDDQ Isolated output Power Supply 3.3V/2.5V CLK Synchronous Clock VSS Ground CKE Clock Enable CE, CE2, CE2 Synchronous Chip Enable 4 BWx (x=a-d) Synchronous Byte Write Inputs OE Output Enable ZZ Power Sleep Mode Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI 119-PIN PBGA PACKAGE CONFIGURATION 128K x 36 (TOP VIEW) 1 2 3 4 5 6 A VDDQ A A NC A A VDDQ B NC CE2 A ADV A CE2 NC C NC A A VDD A A NC D DQc DQPc VSS NC Vss DQPb DQb E DQc DQc VSS CE Vss DQb DQb F VDDQ DQc VSS OE Vss DQb VDDQ G DQc DQc BWc NC BWb DQb DQb H DQc DQc VSS WE Vss DQb DQb J VDDQ VDD NC VDD NC VDD VDDQ K DQd DQd VSS CLK Vss DQa DQa L DQd DQd BWd NC BWa DQa DQa M VDDQ DQd VSS CKE Vss DQa VDDQ N DQd DQd VSS A1 * Vss DQa DQa P DQd DQPd VSS A0 * Vss DQPa DQa R NC A MODE VDD NC A NC T NC NC A A A NC ZZ U VDDQ NC NC NC NC VDDQ NC ® 7 Note: A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. PIN DESCRIPTIONS Symbol Pin Name OE Output Enable A Address Inputs ZZ Power Sleep Mode A0, A1 Synchronous Burst Address Inputs MODE Burst Sequence Selection ADV Synchronous Burst Address Advance/ Load VDD Power Supply WE Synchronous Read/Write Control Input VSS Ground CLK Synchronous Clock NC No Connect CKE Clock Enable DQa-DQd Data Inputs/Outputs CE Synchronous Chip Select DQPa-Pd Parity Data I/O CE2 Synchronous Chip Select VDDQ Output Power Supply CE2 Synchronous Chip Select BWx (x=a-d) Synchronous Byte Write Inputs Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 5 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI 165-PIN PBGA PACKAGE CONFIGURATION ® 256K x 18 (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 11 A NC A BWb NC CE2 CKE ADV B NC A CE CE2 NC NC A A C NC NC VDDQ NC Vss BWa Vss CLK Vss WE Vss D NC DQb VDDQ VDD Vss Vss Vss OE Vss VDD A VDDQ NC NC DQPa VDDQ NC DQa E NC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa F NC DQb VDDQ VDD Vss Vss Vss VDD VDDQ NC DQa G NC DQb VDDQ Vss H NC NC NC VDD VDD Vss Vss Vss Vss VDD VDD VDDQ NC DQa J DQb NC VDDQ VDD Vss Vss NC NC ZZ Vss Vss VDD VDDQ DQa NC K DQb NC VDDQ VDD Vss Vss Vss VDD VDDQ DQa VDD Vss Vss VDD VDDQ DQa VDDQ VDD Vss Vss Vss NC NC L DQb NC VDDQ M DQb NC Vss VDD VDDQ DQa NC N DQPb NC Vss A NC NC NC NC Vss NC NC NC VDDQ A P NC A NC R MODE NC A A NC A A A1* A0* NC A VDDQ A NC A A Note: A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired. PIN DESCRIPTIONS Symbol Pin Name MODE Burst Sequence Selection A Address Inputs VDD 3.3V/2.5V Power Supply A0, A1 Synchronous Burst Address Inputs NC No Connect ADV Synchronous Burst Address Advance/ Load DQx Data Inputs/Outputs DQPx Parity Data I/O WE Synchronous Read/Write Control Input VDDQ Isolated output Power Supply 3.3V/2.5V CLK Synchronous Clock VSS Ground CKE Clock Enable CE, CE2, CE2 Synchronous Chip Enable 6 BWx (x=a,b) Synchronous Byte Write Inputs OE Output Enable ZZ Power Sleep Mode Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI 119-PIN PBGA PACKAGE CONFIGURATION ® 256K x 18 (TOP VIEW) 1 2 3 4 5 6 7 A VDDQ A A NC A A VDDQ B NC CE2 A ADV A CE2 NC C NC A A VDD A A NC D DQb NC VSS NC Vss DQPa NC E DQb VSS CE Vss NC DQa F NC VDDQ NC VSS OE Vss DQa VDDQ G NC DQb BWb NC NC NC DQa H DQb NC WE Vss DQa NC J VDDQ VDD VSS NC VDD NC VDD VDDQ K NC DQb VSS CLK Vss NC DQa L DQb NC NC NC BWa DQa NC M VDDQ DQb VSS CKE Vss NC VDDQ N DQb NC VSS A1 * Vss DQa NC P NC DQPb VSS A0 * Vss NC DQa R NC A MODE VDD NC A NC T NC A A NC A A ZZ U VDDQ NC NC NC NC NC VDDQ Note: A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired. PIN DESCRIPTIONS Symbol Pin Name OE Output Enable A Address Inputs ZZ Power Sleep Mode A0, A1 Synchronous Burst Address Inputs MODE Burst Sequence Selection ADV Synchronous Burst Address Advance/ Load VDD Power Supply WE Synchronous Read/Write Control Input VSS Ground CLK Synchronous Clock NC No Connect CKE Clock Enable DQa-DQb Data Inputs/Outputs CE Synchronous Chip Select DQPa-Pb Parity Data I/O CE2 Synchronous Chip Select VDDQ Output Power Supply CE2 Synchronous Chip Select BWx (x=a,b) Synchronous Byte Write Inputs Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 7 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® PIN CONFIGURATION VDDQ VDDQ DQb DQc DQb Vss NC VDD ZZ DQc NC VDD DQa DQd DQa DQd VDDQ VDDQ Vss NC Vss DQa Vss DQd DQa DQd DQa DQa Vss DQd DQd Vss VDDQ VDDQ DQa DQa DQPa DQd DQd NC NC OE ADV NC CKE CLK WE CE2 VDD Vss BWa BWc BWb BWd CE2 CE A A NC DQb DQb VDDQ Vss DQb DQb DQb DQb Vss VDDQ DQb DQb Vss NC VDD ZZ DQa DQa VDDQ Vss DQa DQa DQa DQa Vss VDDQ DQa DQa NC A A Vss A Vss A DQc A DQc DQb A DQb NC A DQc DQc NC DQb DQb VDD Vss Vss Vss NC NC VDDQ A A NC OE ADV NC CKE CLK WE CE2 VDD Vss BWa BWc BWb BWd CE2 CE A A VDDQ A1 A0 MODE DQd DQd DQPd DQc A VDDQ DQb A DQd DQd Vss DQc A DQd DQb 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 1 79 2 78 3 77 4 76 5 75 6 74 7 73 8 72 9 71 10 70 11 69 12 68 13 67 14 66 15 65 16 64 17 63 18 62 19 61 20 60 21 59 22 58 23 57 24 56 25 55 26 54 27 53 28 52 29 51 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A Vss DQd NC MODE VDDQ DQPb A A DQd A DQd A NC Vss A DQc NC VDD A DQc NC A VDDQ NC Vss VDD DQc Vss DQc NC NC DQc DQc A1 A0 Vss A VDDQ A DQc A DQc 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 1 79 2 78 3 77 4 76 5 75 6 74 7 73 8 72 9 71 10 70 11 69 12 68 13 67 14 66 15 65 16 64 17 63 18 62 19 61 20 60 21 59 22 58 23 57 24 56 25 55 26 54 27 53 28 52 29 51 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A DQPc A A 100-Pin TQFP 128K x 32 128K x 36 PIN DESCRIPTIONS A0, A1 8 Synchronous Address Inputs. These pins must tied to the two LSBs of the address bus. A Synchronous Address Inputs CLK Synchronous Clock ADV Synchronous Burst Address Advance BWa-BWd Synchronous Byte Write Enable WE Write Enable CKE Clock Enable Vss Ground for Core NC Not Connected CE, CE2, CE2 Synchronous Chip Enable OE Output Enable DQa-DQd Synchronous Data Input/Output DQPa-DQPd Parity Data I/O MODE Burst Sequence Selection VDD +3.3V/2.5V Power Supply VSS Ground for output Buffer VDDQ Isolated Output Buffer Supply: +3.3V/2.5V ZZ Snooze Enable Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® PIN CONFIGURATION VDDQ Vss DQb DQb DQPb NC Vss VDDQ MODE NC NC NC NC ADV NC OE CKE CLK WE CE2 VDD Vss BWa NC BWb NC CE2 CE A A A NC NC VDDQ Vss NC DQPa DQa DQa Vss VDDQ DQa DQa Vss NC VDD ZZ DQa DQa VDDQ Vss DQa DQa NC NC Vss VDDQ NC NC NC A A DQb A DQb A NC Vss A DQb NC VDD A DQb NC A VDDQ NC Vss VDD DQb Vss DQb NC NC NC NC A1 A0 Vss A VDDQ A NC A NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 1 79 2 78 3 77 4 76 5 75 6 74 7 73 8 72 9 71 10 70 11 69 12 68 13 67 14 66 15 65 16 64 17 63 18 62 19 61 20 60 21 59 22 58 23 57 24 56 25 55 26 54 27 53 28 52 29 51 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 A NC A A 100-Pin TQFP 256K x 18 PIN DESCRIPTIONS A0, A1 Synchronous Address Inputs. These pins must tied to the two LSBs of the address bus. A Synchronous Address Inputs CLK Synchronous Clock ADV Synchronous Burst Address Advance BWa-BWd Synchronous Byte Write Enable WE Write Enable CKE Clock Enable Vss Ground for Core NC Not Connected CE, CE2, CE2 Synchronous Chip Enable OE Output Enable DQa-DQd Synchronous Data Input/Output DQPa-DQPd Parity Data I/O MODE Burst Sequence Selection VDD +3.3V/2.5V Power Supply VSS Ground for output Buffer VDDQ Isolated Output Buffer Supply: +3.3V/2.5V ZZ Snooze Enable Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 9 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® STATE DIAGRAM READ READ READ BURST WRITE BEGIN READ DS READ WRITE DESELECT BURST BURST READ BEGIN WRITE DS BURST DS BURST DS DS WRITE BURST WRITE READ WRITE WRITE BURST SYNCHRONOUS TRUTH TABLE(1) Operation Not Selected Not Selected Not Selected Not Selected Continue Begin Burst Read Continue Burst Read NOP/Dummy Read Dummy Read Begin Burst Write Continue Burst Write NOP/Write Abort Write Abort Ignore Clock Notes: Address Used CE CE2 CE CE2 ADV WE BW BWx OE CKE CLK N/A N/A N/A N/A External Address Next Address External Address Next Address External Address Next Address N/A Next Address Current Address H X X X L X L X L X L X X X L X X H X H X H X H X X X X H X L X L X L X L X X L L L H L H L H L H L H X X X X X H X H X L X L X X X X X X X X X X L L H H X X X X X L L H H X X X X X L L L L L L L L L L L L H ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ ↑ 1. 2. 3. 4. "X" means don't care. The rising edge of clock is symbolized by ↑ A continue deselect cycle can only be entered if a deselect cycle is executed first. WE = L means Write operation in Write Truth Table. WE = H means Read operation in Write Truth Table. 5. Operation finally depends on status of asynchronous pins (ZZ and OE). 10 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® ASYNCHRONOUS TRUTH TABLE(1) Operation ZZ OE I/O STATUS Sleep Mode H L L L L X L H X X High-Z DQ High-Z Din, High-Z High-Z Read Write Deselected Notes: 1. X means "Don't Care". 2. For write cycles following read cycles, the output buffers must be disabled with OE, otherwise data bus contention will occur. 3. Sleep Mode means power Sleep Mode where stand-by current does not depend on cycle time. 4. Deselected means power Sleep Mode where stand-by current depends on cycle time. WRITE TRUTH TABLE (x18) Operation READ WRITE BYTE a WRITE BYTE b WRITE ALL BYTEs WRITE ABORT/NOP Notes: WE BW BWa BW BWb H L L L L X L H L H X H L L H 1. X means "Don't Care". 2. All inputs in this table must beet setup and hold time around the rising edge of CLK. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 11 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® WRITE TRUTH TABLE (x32/x36) Operation READ WRITE BYTE a WRITE BYTE b WRITE BYTE c WRITE BYTE d WRITE ALL BYTEs WRITE ABORT/NOP Notes: WE BW BWa BW BWb BW BWc BW BWd H L L L L L L X L H H H L H X H L H H L H X H H L H L H X H H H L L H 1. X means "Don't Care". 2. All inputs in this table must beet setup and hold time around the rising edge of CLK. INTERLEAVED BURST ADDRESS TABLE (MODE = VDD or NC) External Address A1 A0 1st Burst Address A1 A0 2nd Burst Address A1 A0 3rd Burst Address A1 A0 00 01 10 11 01 00 11 10 10 11 00 01 11 10 01 00 12 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® LINEAR BURST ADDRESS TABLE (MODE = VSS) 0,0 A1', A0' = 1,1 0,1 1,0 ABSOLUTE MAXIMUM RATINGS(1) Symbol TSTG PD IOUT VIN, VOUT VIN Parameter Storage Temperature Power Dissipation Output Current (per I/O) Voltage Relative to VSS for I/O Pins Voltage Relative to VSS for for Address and Control Inputs Value –65 to +150 1.6 100 –0.5 to VDDQ + 0.5 –0.5 to 4.6 Unit °C W mA V V Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. This device contains circuity to protect the inputs against damage due to high static voltages or electric fields; however, precautions may be taken to avoid application of any voltage higher than maximum rated voltages to this high-impedance circuit. 3. This device contains circuitry that will ensure the output devices are in High-Z at power up. OPERATING RANGE (IS61NLPx) Range Commercial Industrial Ambient Temperature 0°C to +70°C -40°C to +85°C VDD 3.3V ± 5% 3.3V ± 5% VDDQ 3.3V / 2.5V ± 5% 3.3V / 2.5V ± 5% VDD 2.5V ± 5% 2.5V ± 5% VDDQ 2.5V ± 5% 2.5V ± 5% OPERATING RANGE (IS61NVPx) Range Commercial Industrial Ambient Temperature 0°C to +70°C -40°C to +85°C Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 13 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® DC ELECTRICAL CHARACTERISTICS (Over Operating Range) 3.3V 2.5V Symbol Parameter Test Conditions Min. Max. Min. Max. Unit VOH Output HIGH Voltage IOH = –4.0 mA (3.3V) IOH = –1.0 mA (2.5V) 2.4 — 2.0 — V VOL Output LOW Voltage IOL = 8.0 mA (3.3V) IOL = 1.0 mA (2.5V) — 0.4 — 0.4 V VIH(1) Input HIGH Voltage 2.0 VDD + 0.3 1.7 VDD + 0.3 V VIL Input LOW Voltage –0.3 0.8 –0.3 0.7 V ILI Input Leakage Current VSS ≤ VIN ≤ VDD(1) –5 5 –5 5 µA ILO Output Leakage Current VSS ≤ VOUT ≤ VDDQ, OE = VIH –5 5 –5 5 µA (1) Note: 1. Overshoot: VIH (AC) < VDD + 2.0V (Pulse width less than tKC/2). Undershoot: VIL (AC) > -2V (Pulse width less than tKC/2). POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) -200 MAX x18 x32/x36 Symbol Parameter Test Conditions ICC AC Operating Supply Current Device Selected, Com. OE = VIH, ZZ ≤ VIL, Ind. All Inputs ≤ 0.2V or ≥ VDD – 0.2V, Cycle Time ≥ tKC min. 225 250 225 250 200 210 200 210 mA ISB Standby Current TTL Input Device Deselected, VDD = Max., All Inputs ≤ VIL or ≥ VIH, ZZ ≤ VIL, f = Max. Com. Ind. 90 100 90 100 90 100 90 100 mA ISBI Standby Current CMOS Input Device Deselected, VDD = Max., VIN ≤ VSS + 0.2V or ≥VDD – 0.2V f=0 Com. Ind. typ.(2) 70 75 70 75 70 75 70 75 mA ZZ>VIH Com. Ind. typ.(2) 30 35 30 35 30 35 30 35 mA ISB2 Sleep Mode Temp. range -250 MAX x18 x32/x36 Unit 40 20 Note: 1. MODE pin has an internal pullup and should be tied to VDD or VSS. It exhibits ±100µA maximum leakage current when tied to ≤ VSS + 0.2V or ≥ VDD – 0.2V. 2. Typical values are measured at VDD = 3.3V, TA = 25oC and not 100% tested. 14 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® CAPACITANCE(1,2) Symbol Parameter CIN Input Capacitance COUT Input/Output Capacitance Conditions Max. Unit VIN = 0V 6 pF VOUT = 0V 8 pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V. 3.3V I/O AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load Unit 0V to 3.0V 1.5 ns 1.5V See Figures 1 and 2 3.3V I/O OUTPUT LOAD EQUIVALENT 317 Ω +3.3V Zo= 50Ω OUTPUT OUTPUT 50Ω 5 pF Including jig and scope 351 Ω 1.5V Figure 1 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 Figure 2 15 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® 2.5V I/O AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load Unit 0V to 2.5V 1.5 ns 1.25V See Figures 3 and 4 2.5V I/O OUTPUT LOAD EQUIVALENT 1,667 Ω +2.5V ZO = 50Ω OUTPUT OUTPUT 50Ω 5 pF Including jig and scope 1,538 Ω 1.25V Figure 3 16 Figure 4 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® READ/WRITE CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) -250 Min. Max. -200 Min. Max. Symbol Parameter fmax Clock Frequency — 250 — 200 MHz tKC Cycle Time 4.0 — 5 — ns tKH Clock High Time 1.7 — 2 — ns tKL Clock Low Time 1.7 — 2 — ns Clock Access Time — 2.6 — 3.1 ns Clock High to Output Invalid 0.8 — 1.5 — ns tKQLZ Clock High to Output Low-Z 0.8 — 1 — ns tKQHZ(2,3) Clock High to Output High-Z — 2.6 — 3.0 ns tOEQ tKQ tKQX (2) (2,3) Unit Output Enable to Output Valid — 2.8 — 3.1 ns (2,3) Output Enable to Output Low-Z 0 — 0 — ns (2,3) tOEHZ Output Disable to Output High-Z — 2.6 — 3.0 ns tAS Address Setup Time 1.2 — 1.4 — ns tWS Read/Write Setup Time 1.2 — 1.4 — ns tCES Chip Enable Setup Time 1.2 — 1.4 — ns tSE Clock Enable Setup Time 1.2 — 1.4 — ns tADVS Address Advance Setup Time 1.2 — 1.4 — ns tDS Data Setup Time 1.2 — 1.4 — ns tAH Address Hold Time 0.3 — 0.4 — ns tHE Clock Enable Hold Time 0.3 — 0.4 — ns tWH Write Hold Time 0.3 — 0.4 — ns tCEH Chip Enable Hold Time 0.3 — 0.4 — ns tADVH Address Advance Hold Time 0.3 — 0.4 — ns tDH Data Hold Time 0.3 — 0.4 — ns tPDS ZZ High to Power Down — 2 — 2 cyc tPUS ZZ Low to Power Down — 2 — 2 cyc tOELZ Notes: 1. Configuration signal MODE is static and must not change during normal operation. 2. Guaranteed but not 100% tested. This parameter is periodically sampled. 3. Tested with load in Figure 2. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 17 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® SLEEP MODE ELECTRICAL CHARACTERISTICS Symbol Parameter Conditions Min. ISB2 Current during SLEEP MODE tPDS ZZ active to input ignored 2 cycle tPUS ZZ inactive to input sampled 2 cycle tZZI ZZ active to SLEEP current 2 cycle tRZZI ZZ inactive to exit SLEEP current 0 ns ZZ ≥ VIH Max. Unit 35 mA SLEEP MODE TIMING CLK tPDS ZZ setup cycle tPUS ZZ recovery cycle ZZ tZZI Isupply ISB2 tRZZI All Inputs (except ZZ) Deselect or Read Only Deselect or Read Only Normal operation cycle Outputs (Q) High-Z Don't Care 18 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® READ CYCLE TIMING tKH tKL CLK tKC tADVS tADVH ADV tAS tAH Address A1 A3 A2 tWS tWH WRITE tSE tHE CKE tCES tCEH CE OE tOEQ tOEHZ tKQX tKQ tKQHZ tOEHZ Data Out Q1-1 Q2-1 Q2-2 Q2-3 NOTES: WRITE = L means WE = L and BWx = L WE = L and BWX = L CE = L means CE1 = L, CE2 = H and CE2 = L CE = H means CE1 = H, or CE1 = L and CE2 = H, or CE1 = L and CE2 = L Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 Q2-4 Q3-1 Q3-2 Q3-3 Q3-4 Don't Care Undefined 19 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® WRITE CYCLE TIMING tKH tKL CLK tKC ADV Address A1 A3 A2 WRITE tSE tHE CKE CE OE tDS Data In D1-1 D2-1 D2-2 D2-3 D2-4 D3-1 tDH D3-2 D3-3 D3-4 tOEHZ Data Out Q0-3 Q0-4 NOTES: WRITE = L means WE = L and BWx = L WE = L and BWX = L CE = L means CE1 = L, CE2 = H and CE2 = L CE = H means CE1 = H, or CE1 = L and CE2 = H, or CE1 = L and CE2 = L 20 Don't Care Undefined Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® SINGLE READ/WRITE CYCLE TIMING tKH tKL CLK tSE tHE tKC CKE Address A1 A2 A3 A4 Q1 Q3 A5 A6 A7 A8 A9 WRITE CE ADV OE tOEQ tOELZ Data Out Q4 Q6 Q7 tDS tDH Data In D2 NOTES: WRITE = L means WE = L and BWx = L CE = L means CE1 = L, CE2 = H and CE2 = L CE = H means CE1 = H, or CE1 = L and CE2 = H, or CE1 = L and CE2 = L Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 D5 Don't Care Undefined 21 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® CKE OPERATION TIMING tKH tKL CLK tSE tHE tKC CKE Address A1 A2 A3 A4 A5 A6 WRITE CE ADV OE tKQ tKQHZ tKQLZ Data Out Q1 Q3 Q4 tDS tDH Data In D2 NOTES: WRITE = L means WE = L and BWx = L CE = L means CE1 = L, CE2 = H and CE2 = L CE = H means CE1 = H, or CE1 = L and CE2 = H, or CE1 = L and CE2 = L 22 Don't Care Undefined Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® CE OPERATION TIMING tKH tKL CLK tSE tHE tKC CKE Address A1 A2 A3 A4 A5 WRITE CE ADV OE tOEQ tKQHZ tKQ tKQLZ tOELZ Data Out Q1 Q2 Q4 tDS tDH Data In D3 NOTES: WRITE = L means WE = L and BWx = L CE = L means CE1 = L, CE2 = H and CE2 = L CE = H means CE1 = H, or CE1 = L and CE2 = H, or CE1 = L and CE2 = L Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 D5 Don't Care Undefined 23 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® ORDERING INFORMATION (VDD = 3.3V/VDDQ = 2.5V/3.3V) Commercial Range: 0°C to +70°C Access Time Order Part Number Package 128Kx32 250 IS61NLP12832A-250TQ IS61NLP12832A-250B3 IS61NLP12832A-250B2 100 TQFP 165 PBGA 119 PBGA 200 IS61NLP12832A-200TQ IS61NLP12832A-200B3 IS61NLP12832A-200B2 100 TQFP 165 PBGA 119 PBGA 128Kx36 250 200 IS61NLP12836A-250TQ 100 TQFP IS61NLP12836A-250B3 IS61NLP12836A-250B2 165 PBGA 119 PBGA IS61NLP12836A-200TQ IS61NLP12836A-200B3 IS61NLP12836A-200B2 100 TQFP 165 PBGA 119 PBGA 256Kx18 24 250 IS61NLP25618A-250TQ IS61NLP25618A-250B3 IS61NLP25618A-250B2 100 TQFP 165 PBGA 119 PBGA 200 IS61NLP25618A-200TQ IS61NLP25618A-200B3 IS61NLP25618A-200B2 100 TQFP 165 PBGA 119 PBGA Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® ORDERING INFORMATION (VDD = 3.3V/VDDQ = 2.5V/3.3V) Industrial Range: -40°C to +85°C Access Time Order Part Number Package 128Kx32 250 IS61NLP12832A-250TQI IS61NLP12832A-250B3I IS61NLP12832A-250B2I 100 TQFP 165 PBGA 119 PBGA 200 IS61NLP12832A-200TQI IS61NLP12832A-200TQLI IS61NLP12832A-200B3I IS61NLP12832A-200B2I 100 TQFP 100 TQFP, Lead-free 165 PBGA 119 PBGA 128Kx36 250 IS61NLP12836A-250TQI IS61NLP12836A-250B3I IS61NLP12836A-250B2I 100 TQFP 165 PBGA 119 PBGA 200 IS61NLP12836A-200TQI IS61NLP12836A-200TQLI IS61NLP12836A-200B3I IS61NLP12836A-200B2I 100 TQFP 100 TQFP, Lead-free 165 PBGA 119 PBGA 256Kx18 250 IS61NLP25618A-250TQI IS61NLP25618A-250B3I IS61NLP25618A-250B2I 100 TQFP 165 PBGA 119 PBGA 200 IS61NLP25618A-200TQI IS61NLP25618A-200TQLI IS61NLP25618A-200B3I IS61NLP25618A-200B2I 100 TQFP 100 TQFP, Lead-free 165 PBGA 119 PBGA Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 25 IS61NLP12832A IS61NLP12836A/IS61NVP12836A IS61NLP25618A/IS61NVP25618A ISSI ® ORDERING INFORMATION (VDD = 2.5V/VDDQ = 2.5V) Commercial Range: 0°C to +70°C Access Time Order Part Number Package 128Kx36 250 IS61NVP12836A-250TQ IS61NVP12836A-250B3 IS61NVP12836A-250B2 100 TQFP 165 PBGA 119 PBGA 200 IS61NVP12836A-200TQ IS61NVP12836A-200B3 IS61NVP12836A-200B2 100 TQFP 165 PBGA 119 PBGA 256Kx18 250 200 IS61NVP25618A-250TQ 100 TQFP IS61NVP25618A-250B3 IS61NVP25618A-250B2 165 PBGA 119 PBGA IS61NVP25618A-200TQ IS61NVP25618A-200B3 IS61NVP25618A-200B2 100 TQFP 165 PBGA 119 PBGA Order Part Number Package Industrial Range: -40°C to +85°C Access Time 128Kx36 250 IS61NVP12836A-250TQI IS61NVP12836A-250B3I IS61NVP12836A-250B2I 100 TQFP 165 PBGA 119 PBGA 200 IS61NVP12836A-200TQI IS61NVP12836A-200B3I IS61NVP12836A-200B2I 100 TQFP 165 PBGA 119 PBGA 256Kx18 26 250 IS61NVP25618A-250TQI IS61NVP25618A-250B3I IS61NVP25618A-250B2I 100 TQFP 165 PBGA 119 PBGA 200 IS61NVP25618A-200TQI IS61NVP25618A-200B3I IS61NVP25618A-200B2I 100 TQFP 165 PBGA 119 PBGA Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 09/12/05 ISSI PACKAGING INFORMATION ® Plastic Ball Grid Array Package Code: B (119-pin) φ b (119X) E A 7 6 5 4 D2 D1 e A2 A3 E2 Sym. Min. N0. Leads Max. SEATING PLANE INCHES Min. Max. Notes: 119 A — 2.41 — 0.095 A1 0.50 0.70 0.020 0.028 A2 0.80 1.00 0.032 0.039 A3 1.30 1.70 0.051 0.067 A4 0.56 BSC 0.60 0.90 0.024 0.035 D 21.80 22.20 0.858 0.874 20.32 BSC 0.800 BSC D2 19.40 19.60 0.764 0.772 E 13.80 14.20 0.543 0.559 E1 E2 e 7.62 BSC 11.90 12.10 1.27 BSC 1. Controlling dimension: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D1 and E do not include mold flash protrusion and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. 0.022 BSC b D1 E1 A1 A4 MILLIMETERS 1 A B C D E F G H J K L M N P R T U 30ϒ D 3 2 0.300 BSC 0.469 0.476 0.050 BSC Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. B 02/12/03 ISSI PACKAGING INFORMATION ® Ball Grid Array Package Code: B (165-pin) BOTTOM VIEW TOP VIEW A1 CORNER 1 2 3 4 A1 CORNER φ b (165X) 5 6 7 8 9 10 11 10 11 9 8 7 6 5 4 3 2 1 A A B B C C D D E E e F F G G D D1 H H J J K K L L M M N N P P R R e E1 E A2 A A1 BGA - 13mm x 15mm MILLIMETERS Sym. Min. N0. Leads Nom. Max. Notes: 1. Controlling dimensions are in millimeters. INCHES Min. 165 Nom. Max. 165 A — — 1.20 — A1 0.25 0.33 0.40 0.010 — 0.047 0.013 0.016 A2 — 0.79 — — 0.031 — D 14.90 15.00 15.10 0.587 0.591 0.594 D1 13.90 14.00 14.10 0.547 0.551 0.555 E 12.90 13.00 13.10 0.508 0.512 0.516 E1 9.90 10.00 10.10 0.390 0.394 0.398 e — 1.00 — — 0.039 — b 0.40 0.45 0.50 0.016 0.018 0.020 Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. A 06/11/03 ISSI PACKAGING INFORMATION TQFP (Thin Quad Flat Pack Package) Package Code: TQ D D1 E E1 N L1 L C 1 e SEATING PLANE A2 A b A1 Thin Quad Flat Pack (TQ) Inches Millimeters Min Max Min Max Millimeters Symbol Min Max Ref. Std. No. Leads (N) 100 A — 1.60 — 0.063 A1 0.05 0.15 0.002 0.006 A2 1.35 1.45 0.053 0.057 b 0.22 0.38 0.009 0.015 D 21.90 22.10 0.862 0.870 D1 19.90 20.10 0.783 0.791 E 15.90 16.10 0.626 0.634 E1 13.90 14.10 0.547 0.555 e 0.65 BSC 0.026 BSC L 0.45 0.75 0.018 0.030 L1 1.00 REF. 0.039 REF. C 0o 7o 0o 7o 128 — 1.60 0.05 0.15 1.35 1.45 0.17 0.27 21.80 22.20 19.90 20.10 15.80 16.20 13.90 14.10 0.50 BSC 0.45 0.75 1.00 REF. 0o 7o Integrated Silicon Solution, Inc. — 1-800-379-4774 PK13197LQ Rev. D 05/08/03 Inches Min Max — 0.063 0.002 0.006 0.053 0.057 0.007 0.011 0.858 0.874 0.783 0.791 0.622 0.638 0.547 0.555 0.020 BSC 0.018 0.030 0.039 REF. 0o 7o Notes: 1. All dimensioning and tolerancing conforms to ANSI Y14.5M-1982. 2. Dimensions D1 and E1 do not include mold protrusions. Allowable protrusion is 0.25 mm per side. D1 and E1 do include mold mismatch and are determined at datum plane -H-. 3. Controlling dimension: millimeters. ®