PHILIPS ISP1507DBS

ISP1507C; ISP1507D
ULPI Hi-Speed Universal Serial Bus host and peripheral
transceiver
Rev. 01 — 28 May 2008
Product data sheet
1. General description
The ISP1507 is a Universal Serial Bus (USB) high-speed host and peripheral transceiver
that is fully compliant with Universal Serial Bus Specification Rev. 2.0 and UTMI+ Low Pin
Interface (ULPI) Specification Rev. 1.1.
The ISP1507 can transmit and receive USB data at high-speed (480 Mbit/s), full-speed
(12 Mbit/s) and low-speed (1.5 Mbit/s), and provides a pin-optimized, physical layer
front-end attachment to USB host, peripheral and OTG devices.
It is ideal for use in portable electronic devices, such as mobile phones, digital still
cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio
players. It allows USB Application-Specific Integrated Circuits (ASICs), Programmable
Logic Devices (PLDs) and any system chip set to interface with the physical layer of the
USB through a 12-pin interface.
The ISP1507 can interface to the link with digital I/O voltages in the range of 1.65 V to
3.6 V.
The ISP1507 is available in HVQFN24 package.
2. Features
n Fully complies with:
u Universal Serial Bus Specification Rev. 2.0
u UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1
n Interfaces to host and peripheral cores; optimized for stand-alone and embedded host
applications with an external VBUS supply; stand-alone peripheral cores, and Session
Request Protocol (SRP)-capable peripheral cores
n Complete Hi-Speed USB physical front-end solution that supports high-speed
(480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)
u Integrated 45 Ω ± 10 % high-speed termination resistors, 1.5 kΩ ± 5 % full-speed
device pull-up resistor, and 15 kΩ ± 5 % host termination resistors
u Integrated parallel-to-serial and serial-to-parallel converters to transmit and receive
u USB clock and data recovery to receive USB data up to ±500 ppm
u Insertion of stuff bits during transmit and discarding of stuff bits during receive
u Non-Return-to-Zero Inverted (NRZI) encoding and decoding
u Supports bus reset, suspend, resume and high-speed detection handshake (chirp)
n Supports SRP for reduced power consumption
u Complete control over bus resistors
u Data line and VBUS pulsing session request methods
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
n
n
n
n
n
u Integrated VBUS voltage comparators
Highly optimized ULPI compliant
u 60 MHz, 8-bit interface between the core and the transceiver
u Supports 60 MHz output clock configuration
u Integrated Phase-Locked Loop (PLL) supporting one crystal or clock frequency:
19.2 MHz (ISP1507CBS) and 26 MHz (ISP1507DBS)
u Fully programmable ULPI-compliant register set
u Internal Power-On Reset (POR) circuit
Flexible system integration and very low current consumption, optimized for portable
devices
u Power-supply input range is 3.0 V to 3.6 V
u Internal voltage regulator supplies 3.3 V and 1.8 V
u Supports external VBUS charge pump
u External VBUS source is controlled using the PSW_N pin; open-drain PSW_N
allows per-port or ganged power control
u FAULT input pin to monitor the external VBUS supply status
u Supports wide range interfacing I/O voltage of 1.65 V to 3.6 V; separate I/O voltage
pins minimize crosstalk
u Typical operating current of 10 mA to 48 mA, depending on the USB speed and
bus utilization
u Typical suspend current of 35 µA
Full industrial grade operating temperature range from −40 °C to +85 °C
4 kV ElectroStatic Discharge (ESD) protection on pins DP, DM, VBUS and GND
Available in a small HVQFN24 (4 mm × 4 mm) Restriction of Hazardous Substances
(RoHS) compliant, halogen-free and lead-free package
3. Applications
n
n
n
n
n
n
n
n
n
n
n
Digital still camera
Digital TV
Digital Video Disc (DVD) recorder
External storage device, for example:
u Magneto-Optical (MO) drive
u Optical drive: CD-ROM, CD-RW, DVD
u Zip drive
Mobile phone
MP3 player
PDA
Printer
Scanner
Set-Top Box (STB)
Video camera
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
2 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
4. Ordering information
Table 1.
Ordering information
Part
Package
Type number
Marking
Crystal or Name
clock
frequency
Description
ISP1507CBS
507C[1]
19.2 MHz
HVQFN24
plastic thermal enhanced very thin quad flat package; SOT616-3
no leads; 24 terminals; body 4 × 4 × 0.85 mm
ISP1507DBS
507D[1]
26 MHz
HVQFN24
plastic thermal enhanced very thin quad flat package; SOT616-3
no leads; 24 terminals; body 4 × 4 × 0.85 mm
[1]
Version
The package marking is the first line of text on the IC package and can be used for IC identification.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
3 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
5. Block diagram
21
CLOCK
16
NXT
8
1, 2,
17 to 20,
22, 24
ULPI
INTERFACE
CONTROLLER
DATA
[7:0]
RESET_N/
PSW_N
REGISTER
MAP
6
DP
5
DM
HIGH-SPEED
USB ATX
14
DIR
ULPI
INTERFACE
USB DATA
SERIALIZER
15
STP
TERMINATION
RESISTORS
USB DATA
DESERIALIZER
VBUS VALID EXTERNAL
USB
CABLE
DRIVE VBUS EXTERNAL
12
POWER-ON
RESET
GLOBAL
RESET
VBUS
COMPARATORS
8
PLL
GLOBAL
CLOCKS
XTAL1
XTAL2
VCC(I/O)
SRP CHARGE
AND DISCHARGE
RESISTORS
10
11
3, 23
CRYSTAL
OSCILLATOR
interface voltage
ISP1507
internal power
REG3V3
REG1V8
VCC
9
VREF
13
7
VBUS/
FAULT
BAND GAP
REFERENCE
VOLTAGE
4
RREF
VOLTAGE
REGULATOR
004aab078
Fig 1.
Block diagram
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
4 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
6. Pinning information
19 DATA5
20 DATA4
21 CLOCK
22 DATA3
terminal 1
index area
23 VCC(I/O)
24 DATA2
6.1 Pinning
DATA1
1
18 DATA6
DATA0
2
17 DATA7
VCC(I/O)
3
RREF
4
DM
5
14 DIR
DP
6
13 REG1V8
16 NXT
RESET_N/ 12
PSW_N
9
REG3V3
15 STP
XTAL2 11
8
XTAL1 10
7
VCC
VBUS/FAULT
ISP1507
004aab079
Transparent top view
Fig 2.
Pin configuration HVQFN24; top view
6.2 Pin description
Table 2.
Pin description
Symbol[1][2]
Pin
Type[3]
Description[4]
DATA1
1
I/O
pin 1 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
DATA0
2
I/O
pin 0 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
VCC(I/O)
3
P
I/O supply rail
RREF
4
AI/O
resistor reference
DM
5
AI/O
data minus (D−) pin of the USB cable
DP
6
AI/O
data plus (D+) pin of the USB cable
VCC
7
P
input supply voltage or battery source
VBUS/FAULT
8
AI/O
This pin has two possible functions:
VBUS (analog input and output) — VBUS pin of the USB cable.
FAULT (input) — Input pin for the external VBUS digital overcurrent or fault detector
signal.
If this pin is not used as either VBUS or FAULT, it must be connected to ground.
5 V tolerant
REG3V3
9
P
3.3 V regulator output
XTAL1
10
AI
crystal oscillator or clock input
XTAL2
11
AO
crystal oscillator output
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
5 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 2.
Pin description …continued
Symbol[1][2]
Pin
RESET_N/PSW_N 12
Type[3]
Description[4]
I/O
This pin has two possible functions:
RESET_N (input) — Active LOW, asynchronous reset input.
3.3 V tolerant; plain input
PSW_N (output) — Active LOW external VBUS power switch or external charge
pump enable.
open-drain; 3.3 V tolerant
If not used, this pin must be connected to VCC(I/O).
REG1V8
13
P
1.8 V regulator output
DIR
14
O
ULPI direction signal
STP
15
I
ULPI stop signal
slew-rate controlled output (1 ns)
plain input; programmable pull up
NXT
16
O
ULPI next signal
slew-rate controlled output (1 ns)
DATA7
17
I/O
pin 7 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
DATA6
18
I/O
pin 6 of the bidirectional ULPI data bus
DATA5
19
I/O
pin 5 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
slew-rate controlled output (1 ns); plain input; programmable pull down
DATA4
20
I/O
pin 4 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
CLOCK
21
O
60 MHz clock output
slew-rate controlled output (1 ns)
DATA3
22
I/O
pin 3 of the bidirectional ULPI data bus
VCC(I/O)
23
P
I/O supply rail
DATA2
24
I/O
pin 2 of the bidirectional ULPI data bus
GND
die
pad
P
ground supply; down bonded to the exposed die pad (heat sink); to be connected to
the PCB ground
slew-rate controlled output (1 ns); plain input; programmable pull down
slew-rate controlled output (1 ns); plain input; programmable pull down
[1]
Symbol names ending with underscore N, for example, NAME_N, indicate active LOW signals.
[2]
For details on external components required on each pin, see bill of materials and application diagrams in Section 16.
[3]
I = input; O = output; I/O = digital input/output; AI = analog input; AO = analog output; AI/O = analog input/output; P = power or ground
pin.
[4]
A detailed description of these pins can be found in Section 7.10.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
6 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
7. Functional description
7.1 ULPI controller
The ISP1507 provides a 12-pin interface that is compliant with UTMI+ Low Pin Interface
(ULPI) Specification Rev. 1.1. This interface must be connected to the USB link.
The ULPI controller provides the following functions:
•
•
•
•
•
•
•
•
•
•
ULPI compliant and register set
Allows full control over the USB peripheral, host and SRP functionality
Parses the USB transmit and receive data
Prioritizes the USB receive data, USB transmit data, interrupts and register operations
Low-power mode
External VBUS source control
VBUS monitoring, charging and discharging
6-pin serial mode and 3-pin serial mode
Generates RXCMDs; status updates
Maskable interrupts
For more information on the ULPI protocol, see Section 9.
7.2 USB serializer and deserializer
The USB data serializer prepares data to transmit on the USB bus. To transmit data, the
USB link sends a transmit command and data on the ULPI bus. The serializer performs
parallel-to-serial conversion, bit stuffing and NRZI encoding. For packets with a PID, the
serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end
of the packet. When the serializer is busy and cannot accept any more data, the ULPI
controller deasserts NXT.
The USB data deserializer decodes data received from the USB bus. When data is
received, the deserializer strips the SYNC and EOP patterns, and then performs
serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data
payload. The ULPI controller sends data to the USB link by asserting DIR, and then
asserting NXT whenever a byte is ready. The deserializer also detects various receive
errors, including bit stuff errors, elasticity buffer underrun or overrun, and byte-alignment
errors.
7.3 Hi-Speed USB (USB 2.0) ATX
The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to
transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for
USB peripheral, host and OTG implementations. The following circuitry is included:
• Differential drivers to transmit data at high-speed, full-speed and low-speed
• Differential and single-ended receivers to receive data at high-speed, full-speed and
low-speed
• Squelch circuit to detect high-speed bus activity
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
7 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
•
•
•
•
High-speed disconnect detector
45 Ω high-speed bus terminations on DP and DM for peripheral and host modes
1.5 kΩ pull-up resistor on DP for full-speed peripheral mode
15 kΩ bus terminations on DP and DM for host and OTG modes
For details on controlling resistor settings, see Table 7.
7.4 Voltage regulator
The ISP1507 contains a built-in voltage regulator that conditions the VCC supply for use
inside the ISP1507. The voltage regulator:
• Supports input supply range of 3.0 V < VCC < 3.6 V
• Supplies internal circuitry with 1.8 V and 3.3 V
Remark: The REG1V8 and REG3V3 pins require external decoupling capacitors. For
details, see Section 16.
7.5 Crystal oscillator and PLL
The ISP1507 has a built-in crystal oscillator and a Phase-Locked Loop (PLL) for clock
generation.
The crystal oscillator takes a sine-wave input from an external crystal on the XTAL1 pin,
and converts it to a square wave clock for internal use. Alternatively, a square wave clock
of the same frequency can also be directly driven into the XTAL1 pin. Using an existing
square wave clock can save the cost of the crystal and also reduce the board size.
The PLL takes the square wave clock from the crystal oscillator, and multiplies or divides it
into various frequencies for internal use.
The PLL produces the following frequencies, irrespective of the clock source:
•
•
•
•
•
60 MHz clock for the ULPI controller
1.5 MHz for the low-speed USB data
12 MHz for the full-speed USB data
480 MHz for the high-speed USB data
Other internal frequencies for data conversion and data recovery
7.6 VBUS comparators
The ISP1507 provides three comparators, VBUS valid comparator, session valid
comparator and session end comparator, to detect the VBUS voltage level.
7.6.1 VBUS valid comparator
This comparator is used by hosts and A-devices to determine whether the voltage on
VBUS is at a valid level for operation. The ISP1507 minimum threshold for the VBUS valid
comparator is VA_VBUS_VLD. Any voltage on VBUS below VA_VBUS_VLD is considered a fault.
During power-up, it is expected that the comparator output will be ignored.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
8 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
While it is possible for the external 5 V supply to use the ISP1507 internal A_VBUS_VLD
comparator, typical 5 V supplies must provide their own power fault indicator that can be
connected as an input to the ISP1507 FAULT pin.
7.6.2 Session valid comparator
The session valid comparator is a TTL-level input that determines when VBUS is high
enough for a session to start. Peripherals, A-devices and B-devices use this comparator to
detect when a session is started. The A-device also uses this comparator to determine
when a session is completed. The session valid threshold of the ISP1507 is VB_SESS_VLD,
with a hysteresis of Vhys(B_SESS_VLD).
7.6.3 Session end comparator
The ISP1507 session end comparator determines when VBUS is below the B-device
session end threshold. The B-device uses this threshold to determine when a session has
ended. The session end threshold of the ISP1507 is VB_SESS_END.
7.7 SRP charge and discharge resistors
The ISP1507 provides on-chip resistors for short-term charging and discharging of VBUS.
These are used by the B-device to request a session, prompting the A-device to restore
the VBUS power. First, the B-device makes sure that VBUS is fully discharged from the
previous session by setting the DISCHRG_VBUS register bit to logic 1 and waiting for
SESS_END to be logic 1. Then the B-device charges VBUS by setting the CHRG_VBUS
register bit to logic 1. The A-device sees that VBUS is charged above the session valid
threshold and starts a session by turning on the VBUS power.
7.8 Band gap reference voltage
The band gap circuit provides a stable internal voltage reference to bias the analog
circuitry. The band gap requires an accurate external reference resistor, RRREF, connected
between the RREF and GND pins. For details, see Section 16.
7.9 Power-on reset
The ISP1507 has an internal power-on reset circuit that resets all internal logic on
power-up. The ULPI is also reset at power-up.
Remark: When CLOCK starts toggling after power-up, the USB link must issue a reset
command over the ULPI bus to ensure correct operation of the ISP1507.
7.10 Detailed description of pins
7.10.1 DATA[7:0]
The ISP1507 is a Physical layer (PHY) containing a USB transceiver. DATA[7:0] is a
bidirectional data bus. The USB link must drive DATA[7:0] to LOW when the ULPI bus is
idle. When the link has data to transmit to the PHY, it drives a nonzero value.
Weak pull-down resistors are incorporated into DATA[7:0] pins as part of the interface
protect feature. For details, see Section 9.3.1.
The data bus can be reconfigured to carry various data types, as given in Section 8 and
Section 9.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
9 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
7.10.2 VCC(I/O)
The input power pin that sets the I/O voltage level. For details, see Section 12, Section 13
and Section 16. VCC(I/O) provides power to on-chip pads of the following pins:
•
•
•
•
•
•
CLOCK
DATA[7:0]
DIR
NXT
RESET_N
STP
7.10.3 RREF
Resistor reference analog I/O pin. A resistor, RRREF, must be connected between RREF
and GND, as shown in Section 16. This provides an accurate voltage reference that
biases internal analog circuitry. Less accurate resistors cannot be used and will render the
ISP1507 unusable.
7.10.4 DP and DM
The DP (data plus) and DM (data minus) are USB differential data pins. These must be
connected to the D+ and D− pins of the USB receptacle.
7.10.5 VCC
VCC is the main input supply voltage for the ISP1507. Decoupling capacitors are
recommended. For details, see Section 16.
7.10.6 VBUS/FAULT
This pin provides two options for VBUS driving and monitoring. If neither function is used,
this pin must be connected to ground.
7.10.6.1
VBUS
By default, this pin acts as an input to VBUS comparators, and also charges and
discharges VBUS for SRP.
The VBUS pin requires a capacitive load as shown in Section 16.
To prevent electrical overstress, it is strongly recommended that you attach a series
resistor on the VBUS pin (RVBUS). RVBUS must not be attached when using the ISP1507
internal charge pump. For details, see Section 16.
7.10.6.2
FAULT (external overcurrent or fault detector)
If an external VBUS overcurrent or fault circuit is used, the output fault indicator of that
circuit can be connected to the ISP1507 FAULT input pin. The ISP1507 will inform the link
of VBUS fault events by sending RXCMDs on the ULPI bus. To use the FAULT pin, the link
must:
• Set the USE_EXT_VBUS_IND register bit to logic 1.
• Set the polarity of the external fault signal using the IND_COMPL register bit.
• Set the IND_PASSTHRU register bit to logic 1.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
10 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
7.10.7 REG3V3 and REG1V8
Regulator output voltage. These supplies are used to power the ISP1507 internal digital
and analog circuits, and must not be used to power external circuits.
For correct operation of the regulator, it is recommended that you connect REG3V3 and
REG1V8 to decoupling capacitors. For an example, see Section 16.
7.10.8 XTAL1 and XTAL2
XTAL1 is the crystal input, and XTAL2 is the crystal output. The allowed frequency on the
XTAL1 pin depends on the ISP1507 product version.
If the link requires a 60 MHz clock from the ISP1507, then either a crystal must be
attached, or a clock of the same frequency must be driven into XTAL1, with XTAL2 left
floating.
If a crystal is attached, it requires external load capacitors to GND on each terminal of the
crystal. For details, see Section 16.
If at any time the system wants to stop the clock on XTAL1, the link must first put the
ISP1507 into low-power mode. The clock on XTAL1 must be restarted before low-power
mode is exited.
7.10.9 RESET_N/PSW_N
This pin provides two optional functions. If neither function is used, this pin must be
connected to VCC(I/O).
7.10.9.1
RESET_N
An active LOW asynchronous reset pin that resets all circuits in the ISP1507. The
ISP1507 contains an internal power-on reset circuit, and therefore using the RESET_N
pin is optional. If RESET_N is not used, it must be connected to VCC(I/O).
For details on using RESET_N, see Section 9.3.2.
7.10.9.2
PSW_N
PSW_N is an active LOW, open-drain output pin. This pin can be connected to an active
LOW, external VBUS switch or charge pump enable circuit to control the external VBUS
power source. An external pull-up resistor, Rpullup, is required when PSW_N is used. This
pin is open-drain, allowing ganged-mode power control for multiple USB ports. For
application details, see Section 16.
To use the PSW_N pin, the link must disable the reset input by setting the
IGNORE_RESET bit in the PWR_CTRL register (see Section 10.1.14) to logic 1. This will
ensure that PSW_N is not misinterpreted as a reset.
If the link is in host mode, it can enable the external VBUS power source by setting the
DRV_VBUS_EXT bit in the OTG_CTRL register (see Section 10.1.4) to logic 1. The
ISP1507 will drive PSW_N to LOW to enable the external VBUS power source. If the link
detects an overcurrent condition (the VBUS state in RXCMD is not 11b), it must disable the
external VBUS supply by setting DRV_VBUS_EXT to logic 0.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
11 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
7.10.10 DIR
ULPI direction output pin. Controls the direction of the data bus. By default, the ISP1507
holds DIR at LOW, causing the data bus to be an input. When DIR is LOW, the ISP1507
listens for data from the link. The ISP1507 pulls DIR to HIGH only when it has data to
send to the link, which is for one of two reasons:
• To send the USB receive data, RXCMD status updates and register reads data to the
link.
• To block the link from driving the data bus during power-up, reset and low-power
mode (suspend).
For details on DIR usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
7.10.11 STP
ULPI stop input pin. The link must assert STP to signal the end of a USB transmit packet
or a register write operation. When DIR is asserted, the link can optionally assert STP to
abort the ISP1507, causing it to deassert DIR in the next clock cycle. A weak pull-up
resistor is incorporated into the STP pin as part of the interface protect feature. For details,
see Section 9.3.1.
For details on STP usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
7.10.12 NXT
ULPI next data output pin. The ISP1507 holds NXT at LOW, by default. When DIR is LOW
and the link is sending data to the ISP1507, NXT will be asserted to notify the link to
provide the next data byte. When DIR is at HIGH and the ISP1507 is sending data to the
link, NXT will be asserted to notify the link that another valid byte is on the bus. NXT is not
used for register read data or the RXCMD status update.
For details on NXT usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
7.10.13 CLOCK
A 60 MHz interface clock to synchronize the ULPI bus. The ISP1507 provides two
clocking options:
• A crystal is attached between the XTAL1 and XTAL2 pins.
• A clock is driven into the XTAL1 pin, with the XTAL2 pin left floating.
For details on CLOCK usage, refer to UTMI+ Low Pin Interface (ULPI) Specification
Rev. 1.1.
7.10.14 GND (die pad)
Global ground signal. The die pad is exposed on the underside of the package as a
ground plate. This acts as a ground to all circuits in the ISP1507. To ensure correct
operation of the ISP1507, GND must be soldered to the cleanest ground available.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
12 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
8. Modes of operation
8.1 ULPI modes
The ISP1507 ULPI bus can be programmed to operate in four modes. Each mode
reconfigures the signals on the data bus as described in the following subsections. Setting
more than one mode will lead to undefined behavior.
8.1.1 Synchronous mode
This is default mode. At power-up, and when CLOCK is stable, the ISP1507 will enter
synchronous mode. The link must synchronize all ULPI signals to CLOCK, meeting the
set-up and hold times as defined in Section 15. A description of the ULPI pin behavior in
synchronous mode is given in Table 3.
This mode is used by the link to perform the following tasks:
•
•
•
•
High-speed detection handshake (chirp)
Transmit and receive USB packets
Read and write to registers
Receive USB status updates (RXCMDs)
For more information on various synchronous mode protocols, see Section 9.
Table 3.
ULPI signal description
Signal
name
Direction on Signal description
ISP1507
CLOCK
O
DATA[7:0] I/O
60 MHz interface clock. If a crystal is attached or a clock is driven into
the XTAL1 pin, the ISP1507 will drive a 60 MHz output clock.
8-bit data bus. In synchronous mode, the link drives DATA[7:0] to LOW
by default. The link initiates transfers by sending a nonzero data pattern
called TXCMD (transmit command). In synchronous mode, the direction
of DATA[7:0] is controlled by DIR. Contents of DATA[7:0] lines must be
ignored for exactly one clock cycle whenever DIR changes value. This is
called the turnaround cycle.
Data lines have fixed direction and different meaning in low-power and
serial modes.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
13 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 3.
ULPI signal description …continued
Signal
name
Direction on Signal description
ISP1507
DIR
O
Direction: Controls the direction of data bus DATA[7:0]. In synchronous
mode, the ISP1507 drives DIR to LOW by default, making the data bus
an input so that the ISP1507 can listen for TXCMDs from the link. The
ISP1507 drives DIR to HIGH only when it has data for the link. When
DIR and NXT are HIGH, the byte on the data bus contains decoded
USB data. When DIR is HIGH and NXT is LOW, the byte contains
status information called RXCMD (receive command). The only
exception to this rule is when the PHY returns register read data, where
NXT is also LOW, replacing the usual RXCMD byte. Every change in
DIR causes a turnaround cycle on the data bus, during which DATA[7:0]
is not valid and must be ignored by the link.
DIR is always asserted during low-power and serial modes.
STP
I
Stop: In synchronous mode, the link drives STP to HIGH for one cycle
after the last byte of data is sent to the ISP1507. The link can optionally
assert STP to force DIR to be deasserted.
In low-power and serial modes, the link holds STP at HIGH to wake up
the ISP1507, causing the ULPI bus to return to synchronous mode.
NXT
O
Next: In synchronous mode, the ISP1507 drives NXT to HIGH to
throttle data. If DIR is LOW, the ISP1507 asserts NXT to notify the link
to place the next data byte on DATA[7:0] in the following clock cycle. If
DIR is HIGH, the ISP1507 asserts NXT to notify the link that a valid
USB data byte is on DATA[7:0] in the current cycle. The ISP1507 always
drives an RXCMD when DIR is HIGH and NXT is LOW, unless register
read data is to be returned to the link in the current cycle.
NXT is not used in low-power or serial mode.
8.1.2 Low-power mode
When the USB is idle, the link can place the ISP1507 into low-power mode (also called
suspend mode). In low-power mode, the data bus definition changes to that shown in
Table 4. To enter low-power mode, the link sets the SUSPENDM bit in the FUNC_CTRL
register (see Section 10.1.2) to logic 0. To exit low-power mode, the link asserts the STP
signal. The ISP1507 will draw only suspend current from the VCC supply (see Table 44).
During low-power mode, the clock on XTAL1 may be stopped. The clock must be started
again before asserting STP to exit low-power mode. After exiting low-power mode, the
ISP1507 will send an RXCMD to the link if a change was detected in any interrupt source,
and the change still exists. An RXCMD may not be sent if the interrupt condition is
removed before exiting.
For more information on low-power mode enter and exit protocols, refer to UTMI+ Low Pin
Interface (ULPI) Specification Rev. 1.1.
Table 4.
Signal mapping during low-power mode
Signal
Maps to
Direction
Description
LINESTATE0 DATA0
O
combinatorial LINESTATE0 directly driven by the analog receiver
LINESTATE1 DATA1
O
combinatorial LINESTATE1 directly driven by the analog receiver
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
14 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 4.
Signal mapping during low-power mode …continued
Signal
Maps to
Direction
Description
Reserved
DATA2
O
reserved; the ISP1507 will drive this pin to LOW
INT
DATA3
O
active HIGH interrupt indication; will be asserted whenever any unmasked
interrupt occurs
Reserved
DATA[7:4]
O
reserved; the ISP1507 will drive these pins to LOW
8.1.3 6-pin full-speed or low-speed serial mode
If the link requires a 6-pin serial interface to transmit and receive full-speed or low-speed
USB data, it can set the ISP1507 to 6-pin serial mode. In 6-pin serial mode, the DATA[7:0]
bus definition changes to that shown in Table 5. To enter 6-pin serial mode, the link sets
the 6PIN_FSLS_SERIAL bit in the INTF_CTRL register (see Section 10.1.3) to logic 1. To
exit 6-pin serial mode, the link asserts STP. This is provided primarily for links that contain
legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path
to high-speed. An interrupt pin is also provided to inform the link of USB events. If the link
requires CLOCK to be running during 6-pin serial mode, the CLOCK_SUSPENDM
register bit must be set to logic 1.
For more information on 6-pin serial mode enter and exit protocols, refer to UTMI+ Low
Pin Interface (ULPI) Specification Rev. 1.1.
Table 5.
Signal mapping for 6-pin serial mode
Signal
Maps to
Direction
Description
TX_ENABLE
DATA0
I
active HIGH transmit enable
TX_DAT
DATA1
I
transmit differential data on DP and DM
TX_SE0
DATA2
I
transmit single-ended zero on DP and DM
INT
DATA3
O
active HIGH interrupt indication; will be asserted whenever any
unmasked interrupt occurs
RX_DP
DATA4
O
single-ended receive data from DP
RX_DM
DATA5
O
single-ended receive data from DM
RX_RCV
DATA6
O
differential receive data from DP and DM
Reserved
DATA7
O
reserved; the ISP1507 will drive this pin to LOW
8.1.4 3-pin full-speed or low-speed serial mode
If the link requires a 3-pin serial interface to transmit and receive full-speed or low-speed
USB data, it can set the ISP1507 to 3-pin serial mode. In 3-pin serial mode, the data bus
definition changes to that shown in Table 6. To enter 3-pin serial mode, the link sets the
3PIN_FSLS_SERIAL bit in the INTF_CTRL register (see Section 10.1.3) to logic 1. To exit
3-pin serial mode, the link asserts STP. This is primarily provided for links that contain
legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path
to high-speed. An interrupt pin is also provided to inform the link of USB events. If the link
requires CLOCK to be running during 3-pin serial mode, the CLOCK_SUSPENDM
register bit must be set to logic 1.
For more information on 3-pin serial mode enter and exit protocols, refer to UTMI+ Low
Pin Interface (ULPI) Specification Rev. 1.1.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
15 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 6.
Signal mapping for 3-pin serial mode
Signal
Maps to
Direction
Description
TX_ENABLE
DATA0
I
active HIGH transmit enable
DAT
DATA1
I/O
transmit differential data on DP and DM when TX_ENABLE is HIGH
receive differential data from DP and DM when TX_ENABLE is LOW
SE0
DATA2
I/O
transmit single-ended zero on DP and DM when TX_ENABLE is HIGH
receive single-ended zero from DP and DM when TX_ENABLE is LOW
INT
DATA3
O
active HIGH interrupt indication; will be asserted whenever any
unmasked interrupt occurs
Reserved
DATA[7:4]
O
reserved; the ISP1507 will drive these pins to LOW
8.2 USB and OTG state transitions
A Hi-Speed USB peripheral, host or OTG device handles more than one electrical state as
defined in Universal Serial Bus Specification Rev. 2.0 and On-The-Go Supplement to the
USB 2.0 Specification Rev. 1.3. The ISP1507 accommodates the various states through
register bit settings of XCVRSELECT[1:0], TERMSELECT, OPMODE[1:0],
DP_PULLDOWN and DM_PULLDOWN.
Table 7 summarizes operating states. The values of register settings in Table 7 will force
resistor settings as also given in Table 7. Resistor setting signals are defined as follows:
•
•
•
•
RPU_DP_EN enables the 1.5 kΩ pull-up resistor on DP
RPD_DP_EN enables the 15 kΩ pull-down resistor on DP
RPD_DM_EN enables the 15 kΩ pull-down resistor on DM
HSTERM_EN enables the 45 Ω termination resistors on DP and DM
It is up to the link to set the desired register settings.
Table 7.
Operating states and their corresponding resistor settings
Signaling mode
Register settings
Internal resistor settings
XCVR
SELECT
[1:0]
TERM
SELECT
OPMODE
[1:0]
DP_PULL DM_PULL RPU_
DOWN
DOWN
DP_EN
RPD_
DP_EN
RPD_
HSTERM
DM_EN _EN
3-state drivers
XXb
Xb
01b
Xb
Xb
0b
0b
0b
0b
Power-up or
VBUS < VB_SESS_END
01b
0b
00b
1b
1b
0b
1b
1b
0b
00b
0b
10b
1b
1b
0b
1b
1b
1b
General settings
Host settings
Host chirp
Host high-speed
00b
0b
00b
1b
1b
0b
1b
1b
1b
Host full-speed
X1b
1b
00b
1b
1b
0b
1b
1b
0b
Host high-speed or
full-speed suspend
01b
1b
00b
1b
1b
0b
1b
1b
0b
Host high-speed or
full-speed resume
01b
1b
10b
1b
1b
0b
1b
1b
0b
Host low-speed
10b
1b
00b
1b
1b
0b
1b
1b
0b
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
16 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 7.
Operating states and their corresponding resistor settings …continued
Signaling mode
Register settings
Internal resistor settings
XCVR
SELECT
[1:0]
TERM
SELECT
OPMODE
[1:0]
DP_PULL DM_PULL RPU_
DOWN
DOWN
DP_EN
RPD_
DP_EN
RPD_
HSTERM
DM_EN _EN
Host low-speed
suspend
10b
1b
00b
1b
1b
0b
1b
1b
0b
Host low-speed
resume
10b
1b
10b
1b
1b
0b
1b
1b
0b
Host Test J or Test K 00b
0b
10b
1b
1b
0b
1b
1b
1b
Peripheral settings
Peripheral chirp
00b
1b
10b
0b
0b
1b
0b
0b
0b
Peripheral
high-speed
00b
0b
00b
0b
0b
0b
0b
0b
1b
Peripheral full-speed 01b
1b
00b
0b
0b
1b
0b
0b
0b
Peripheral
high-speed or
full-speed suspend
01b
1b
00b
0b
0b
1b
0b
0b
0b
Peripheral
high-speed or
full-speed resume
01b
1b
10b
0b
0b
1b
0b
0b
0b
Peripheral Test J or
Test K
00b
0b
10b
0b
0b
0b
0b
0b
1b
OTG device
peripheral chirp
00b
1b
10b
0b
1b
1b
0b
1b
0b
OTG device
peripheral
high-speed
00b
0b
00b
0b
1b
0b
0b
1b
1b
OTG device
01b
peripheral full-speed
1b
00b
0b
1b
1b
0b
1b
0b
OTG device
peripheral
high-speed and
full-speed suspend
01b
1b
00b
0b
1b
1b
0b
1b
0b
OTG device
peripheral
high-speed and
full-speed resume
01b
1b
10b
0b
1b
1b
0b
1b
0b
OTG device
peripheral Test J or
Test K
00b
0b
10b
0b
1b
0b
0b
1b
1b
OTG settings
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
17 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
9. Protocol description
The following subsections describe the protocol for using the ISP1507.
9.1 ULPI references
The ISP1507 provides a 12-pin ULPI to communicate with the link. It is highly
recommended that you read UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1 and
UTMI+ Specification Rev. 1.0.
9.2 Power-On Reset (POR)
An internal POR is generated when REG1V8 rises above VPOR(trip), for at least
tw(REG1V8_H). The internal POR pulse will also be generated whenever REG1V8 drops
below VPOR(trip) for more than tw(REG1V8_L), and then rises above VPOR(trip) again. The
voltage on REG1V8 is generated from VCC.
To give a better view of the functionality, Figure 3 shows a possible curve of REG1V8. The
internal POR starts with logic 0 at t0. At t1, the detector will see the passing of the trip
level so that POR turns to logic 1 and a delay element will add another tPORP before it
drops to logic 0. If REG1V8 dips from t2 to t3 for > tw(REG1V8_L), another POR pulse is
generated. If the dip at t4 to t5 is too short, that is, < tw(REG1V8_L), the internal POR pulse
will not react and will remain LOW.
REG1V8
VPOR(trip)
t0
t1
t2
t3
tPORP
tPORP
t4
t5
POR
004aaa751
Fig 3.
Internal power-on reset timing
9.3 Power-up, reset and bus idle sequence
Figure 4 shows a typical start-up sequence.
On power-up, the ISP1507 performs an internal power-on reset and asserts DIR to
indicate to the link that the ULPI bus cannot be used. When the internal PLL is stable, the
ISP1507 deasserts DIR. The power-up time depends on the VCC supply rise time, the
crystal start-up time, and PLL start-up time tstartup(o)(CLOCK). Whenever DIR is asserted,
the ISP1507 drives the NXT pin to LOW and drives DATA[7:0] with RXCMD values. When
DIR is deasserted, the link must drive the data bus to a valid level. By default, the link
must drive data to LOW. When the ISP1507 initially deasserts DIR on power-up, the link
must ignore all RXCMDs until it resets the ISP1507. Before beginning USB packets, the
link must set the RESET bit in the FUNC_CTRL register (see Section 10.1.2) to reset the
ISP1507. After the RESET bit is set, the ISP1507 will assert DIR until the internal reset
completes. The ISP1507 will automatically deassert DIR and clear the RESET bit when
reset has completed. After every reset, an RXCMD is sent to the link to update USB status
information. After this sequence, the ULPI bus is ready for use and the link can start USB
operations.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
18 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
If a crystal is attached or a clock is driven into the XTAL1 pin, the ISP1507 will drive a
60 MHz clock out from the CLOCK pin when DIR deasserts. This is shown as CLOCK in
Figure 4.
The recommended power-up sequence for the link is as follows:
1. The link waits for 1 ms, ignoring all the ULPI pin status.
2. The link may start to detect DIR status level. If DIR is detected as LOW for three clock
cycles, the link may send a RESET command.
The ULPI is ready for use.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
19 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
VCC
VCC(I/O)
REG1V8
tPWRUP
internal
REG1V8
detector
internal
POR
XTAL1
bus idle
internal clocks stable
tstartup(PLL)
CLOCK
RESET command
DATA[7:0]
TXCMD D
internal reset
RXCMD
update
DIR
STP
NXT
t1
t2
t3
t4
t5
004aaa885
t1 = VCC and VCC(I/O) are applied to the ISP1507. The ISP1507 regulator starts to turn on.
t2 = ULPI pads detect REG1V8 rising above the REG1V8 regulator threshold and are not in 3-state. These pads may drive
either LOW or HIGH. It is recommended that the link ignores the ULPI pins status during tPWRUP.
t3 = The POR threshold is reached and a POR pulse is generated. After the POR pulse, ULPI pins are driven to a defined level.
DIR is driven to HIGH and the other pins are driven to LOW.
t4 = The internal PLL is stabilized after tstartup(PLL). If the 19.2 MHz or 26 MHz clock is started before POR, the internal PLL will
be stabilized after tstartup(PLL) from POR. The CLOCK pin starts to output 60 MHz. The DIR pin will transition from HIGH to LOW.
The DIR pin will remain LOW before the link issues a RESET command to the ISP1507.
t5 = The power-up sequence is completed and the ULPI bus interface is ready for use.
Fig 4.
Power-up and reset sequence required before the ULPI bus is ready for use
9.3.1 Interface protection
By default, the ISP1507 enables a weak pull-up resistor on STP. If the STP pin is
unexpectedly HIGH at any time, the ISP1507 will protect the ULPI by enabling weak
pull-down resistors on DATA[7:0].
The interface protect feature prevents unwanted activity of the ISP1507 whenever the
ULPI is not correctly driven by the link. For example, when the link powers up more slowly
than the ISP1507.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
20 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
The interface protect feature can be disabled by setting the INTF_PROT_DIS bit to logic 1.
9.3.2 Interface behavior with respect to RESET_N
The use of the RESET_N pin is optional. When RESET_N is asserted (LOW), the
ISP1507 will assert DIR. All logic in the ISP1507 will be reset, including the analog
circuitry and ULPI registers. During reset, the link must drive DATA[7:0] and STP to LOW;
otherwise undefined behavior may result. When RESET_N is deasserted (HIGH), the DIR
output will deassert (LOW) four or five clock cycles later. Figure 5 shows the ULPI
behavior when RESET_N is asserted (LOW), and subsequently deasserted (HIGH). If
RESET_N is not used, it must be connected to VCC(I/O).
CLOCK
RESET_N
DATA[7:0]
Hi-Z (input)
Hi-Z (link must drive)
Hi-Z (input)
Hi-Z (link must drive)
Hi-Z (input)
DIR
STP
Hi-Z (input)
NXT
004aaa720
Fig 5.
Interface behavior with respect to RESET_N
9.4 VBUS power and fault detection
9.4.1 Driving 5 V on VBUS
The ISP1507 supports external 5 V supplies. The ISP1507 can control the external supply
using the active-LOW PSW_N open-drain output pin. To enable the external supply by
driving PSW_N to LOW, the link must set the DRV_VBUS_EXT bit in the OTG_CTRL
register (see Section 10.1.4) to logic 1. When the DRV_VBUS_EXT bit is set, the
DRV_VBUS bit can be set to any value and will be ignored.
9.4.2 Fault detection
The ISP1507 supports external VBUS fault detector circuits. An overcurrent detection
circuit is required for host applications that supply more than 100 mA on VBUS for voltages
between 4.75 V to 5.25 V. For low-power applications supplying less than 100 mA, the
VBUS power line can directly be connected to the VBUS/FAULT pin on the ISP1507 and the
link can utilize the internal A_VBUS_VLD comparator.
The ISP1507 supports external VBUS fault detector circuits that output a digital fault
indicator signal. The indicator signal must be connected to the VBUS/FAULT pin. To enable
the ISP1507 to monitor the digital fault input, the link must set the USE_EXT_VBUS_IND
bit in the OTG_CTRL register (see Section 10.1.4) and the IND_PASSTHRU bit in the
INTF_CTRL register (see Section 10.1.3) to logic 1. For details, see Figure 7.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
21 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
The FAULT input pin is mapped to the A_VBUS_VLD bit in RXCMD. Any changes for the
FAULT input will trigger RXCMD carrying the FAULT condition with A_VBUS_VLD.
9.5 TXCMD and RXCMD
Commands between the ISP1507 and the link are described in the following subsections.
9.5.1 TXCMD
By default, the link must drive the ULPI bus to its idle state of 00h. To send commands and
USB packets, the link drives a nonzero value on DATA[7:0] to the ISP1507 by sending a
byte called TXCMD. Commands include USB packet transmissions, and register reads
and writes. Once the TXCMD is interpreted and accepted by the ISP1507, the NXT signal
is asserted and the link can follow up with the required number of data bytes. The TXCMD
byte format is given in Table 8. Any values other than those in Table 8 are illegal and may
result in undefined behavior.
Various TXCMD packet and register sequences are shown in later sections.
Table 8.
TXCMD byte format
Command Command code
type name DATA[7:6]
Command
Command Command description
payload DATA[5:0] name
Idle
00b
00 0000b
NOOP
No operation. 00h is the idle value of the data bus. The
link must drive NOOP by default.
Packet
transmit
01b
00 0000b
NOPID
Transmit USB data that does not have a PID, such as
chirp and resume signaling. The ISP1507 starts
transmitting only after accepting the next data byte.
00 XXXXb
PID
Transmit USB packet. DATA[3:0] indicates USB packet
identifier PID[3:0].
10 1111b
EXTW
Extended register write command (optional). The 8-bit
address must be provided after the command is
accepted.
XX XXXXb
REGW
Register write command with 6-bit immediate address.
10 1111b
EXTR
Extended register read command (optional). The 8-bit
address must be provided after the command is
accepted.
XX XXXXb
REGR
Register read command with 6-bit immediate address.
Register
write
Register
read
10b
11b
9.5.2 RXCMD
The ISP1507 communicates status information to the link by asserting DIR and sending
an RXCMD byte on the data bus. The RXCMD data byte format is given in Table 9.
The ISP1507 will automatically send an RXCMD whenever there is a change in any of the
RXCMD data fields. The link must be able to accept an RXCMD at any time; including
single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive
packets when NXT is LOW. An example is shown in Figure 6. For details and diagrams,
refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt
condition is removed before exiting.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
22 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 9.
RXCMD byte format
DATA
Name
Description and value
1 to 0
LINESTATE
LINESTATE signals: For a definition of LINESTATE, see Section 9.5.2.1.
DATA0 — LINESTATE[0]
DATA1 — LINESTATE[1]
3 to 2
VBUS state
Encoded VBUS voltage state: For an explanation of the VBUS state, see Section 9.5.2.2.
5 to 4
RxEvent
Encoded USB event signals: For an explanation of RxEvent, see Section 9.5.2.4.
6
reserved
-
7
ALT_INT
By default, this signal is not used and is not needed in typical designs. Optionally, the link can enable
the BVALID_RISE and/or BVALID_FALL bits in the PWR_CTRL register (see Section 10.1.14).
Corresponding changes in BVALID will cause an RXCMD to be sent to the link with the ALT_INT bit
asserted.
CLOCK
Single RXCMD
DATA[ 7:0]
turnaround
RXCMD
turnaround
Back-to-back RXCMDs
turnaround
RXCMD
RXCMD
turnaround
DIR
STP
NXT
004aaa695
Fig 6.
Single and back-to-back RXCMDs from the ISP1507 to the link
9.5.2.1
Linestate encoding
LINESTATE[1:0] reflects the current state of DP and DM. Whenever the ISP1507 detects
a change in DP or DM, an RXCMD will be sent to the link with the new LINESTATE[1:0]
value. The value given on LINESTATE[1:0] depends on the setting of various registers.
Table 10 shows the LINESTATE[1:0] encoding for upstream facing ports, which applies to
peripherals. Table 11 shows the LINESTATE[1:0] encoding for downstream facing ports,
which applies to host controllers. Dual-role devices must choose the correct table,
depending on whether it is in peripheral or host mode.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
23 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 10. LINESTATE[1:0] encoding for upstream facing ports: peripherals
DP_PULLDOWN = 0.[1]
Mode
Full-speed
High-speed
Chirp
XCVRSELECT[1:0]
01, 11
00
00
TERMSELECT
1
0
1
00
SE0
squelch
squelch
01
FS-J
!squelch
!squelch and HS_Differential_Receiver_Output
10
FS-K
invalid
!squelch and !HS_Differential_Receiver_Output
11
SE1
invalid
invalid
LINESTATE[1:0]
[1]
!squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.
Table 11. LINESTATE[1:0] encoding for downstream facing ports: host
DP_PULLDOWN and DM_PULLDOWN = 1.[1]
Mode
Low-speed
Full-speed
High-speed
Chirp
XCVRSELECT[1:0]
10
01, 11
00
00
TERMSELECT
1
1
0
0
OPMODE[1:0]
X
X
00, 01, 11
10
00
SE0
SE0
squelch
squelch
01
LS-K
FS-J
!squelch
!squelch and HS_Differential_Receiver_Output
10
LS-J
FS-K
invalid
!squelch and !HS_Differential_Receiver_Output
11
SE1
SE1
invalid
invalid
LINESTATE[1:0]
[1]
!squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.
9.5.2.2
VBUS state encoding
USB devices must monitor the VBUS voltage for purposes such as overcurrent detection,
starting a session and SRP. The VBUS state field in the RXCMD is an encoding of the
voltage level on VBUS.
The A_VBUS_VLD, SESS_VLD and SESS_END indicators in the VBUS state are directly
taken from internal comparators built-in to the ISP1507, and encoded as shown in Table 9
and Table 12.
An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt
condition is removed before exiting.
Table 12.
Encoded VBUS voltage state
Value
VBUS voltage
SESS_END
SESS_VLD
A_VBUS_VLD
00
VBUS < VB_SESS_END
1
0
0
01
VB_SESS_END ≤ VBUS < VB_SESS_VLD
0
0
0
10
VB_SESS_VLD ≤ VBUS < VA_VBUS_VLD
X
1
0
11
VBUS ≥ VA_VBUS_VLD
X
X
1
Note that VBUS and FAULT share the same pin and cannot be simultaneously used.
A_VBUS_VLD and FAULT will be interpreted by the ISP1507 as shown in Figure 7.
A description on how to use and select the VBUS state encoding is given in
Section 9.5.2.3.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
24 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
A_VBUS_VLD comparator
(VBUS < 4.4 V)
internal A_VBUS_VLD
VBUS/FAULT
(0, X)
RXCMD
A_VBUS_VLD
complement output
(1, 1)
IND_COMPL
USE_EXT_VBUS_IND,
IND_PASSTHRU
Fig 7.
004aaa752
RXCMD A_VBUS_VLD indicator source
9.5.2.3
Using and selecting the VBUS state encoding
The VBUS state encoding is shown in Table 9. The ISP1507 will send an RXCMD to the
link whenever there is a change in the VBUS state. To receive VBUS state updates, the link
must first enable the corresponding interrupts in the USB_INTR_EN_R_E and
USB_INTR_EN_F_E registers.
The link can use the VBUS state to monitor VBUS and take appropriate action. Table 13
shows the recommended usage for typical applications.
Table 13.
VBUS indicators in RXCMD required for typical applications
Application
A_VBUS_VLD
SESS_VLD
SESS_END
Standard host
yes
no
no
Standard peripheral
no
yes
no
OTG A-device
yes
yes
no
OTG B-device
no
yes
yes
Standard USB host controllers: For standard hosts, the system must be able to provide
500 mA on VBUS in the range of 4.75 V to 5.25 V. An external circuit must be used to
detect overcurrent conditions. If the external overcurrent detector provides a digital fault
signal, then the fault signal must be connected to the ISP1507 FAULT input pin, and the
link must do the following:
1. Set the IND_COMPL bit in the INTF_CTRL register (see Section 10.1.3) to logic 0 or
logic 1, depending on the polarity of the external fault signal.
2. Set the IND_PASSTHRU bit in the INTF_CTRL register to logic 1.
3. Set the USE_EXT_VBUS_IND bit in the OTG_CTRL register (see Section 10.1.4) to
logic 1.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
25 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Standard USB peripheral controllers: Standard peripherals must be able to detect
when VBUS is at a sufficient level for operation. SESS_VLD must be enabled to detect the
start and end of USB peripheral operations. Detection of A_VBUS_VLD and SESS_END
thresholds is not needed for standard peripherals.
OTG devices: The ISP1507 provides partial OTG support. A low-power OTG A-device
that supplies less than 100 mA on VBUS can connect the VBUS power to the ISP1507 VBUS
pin. The internal A_VBUS_VLD comparator can be used. If the OTG A-device provides
more than 100 mA on VBUS, an overcurrent detector must be used and Section “Standard
USB host controllers” on page 25 applies. The OTG A-device also uses SESS_VLD to
detect when an OTG B-device is initiating VBUS pulsing SRP.
When an OTG device is configured as an OTG B-device, SESS_VLD must be used to
detect when VBUS is at a sufficient level for operation. SESS_END must be used to detect
when VBUS has dropped to a LOW level, allowing the B-device to safely initiate VBUS
pulsing SRP.
9.5.2.4
RxEvent encoding
The RxEvent field (see Table 14) of the RXCMD informs the link of information related
packets received on the USB bus. RxActive and RxError are defined in USB 2.0
Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05. HostDisconnect is defined
in UTMI+ Specification Rev. 1.0. A short definition is also given in the following
subsections.
Table 14.
Encoded USB event signals
Value
RxActive
RxError
HostDisconnect
00
0
0
0
01
1
0
0
11
1
1
0
10
X
X
1
RxActive: When the ISP1507 has detected a SYNC pattern on the USB bus, it signals an
RxActive event to the link. An RxActive event can be communicated using two methods.
The first method is for the ISP1507 to simultaneously assert DIR and NXT. The second
method is for the ISP1507 to send an RXCMD to the link with the RxActive field in
RxEvent bits set to logic 1. The link must be able to detect both methods. RxActive frames
the receive packet from the first byte to the last byte.
The link must assume that RxActive is set to logic 0 when indicated in an RXCMD or when
DIR is deasserted, whichever occurs first.
The link uses RxActive to time high-speed packets and ensure that bus turnaround times
are met. For more information on the USB packet timing, see Section 9.8.1.
RxError: When the ISP1507 has detected an error while receiving a USB packet, it
deasserts NXT and sends an RXCMD with the RxError field set to logic 1. The received
packet is no longer valid and must be dropped by the link.
HostDisconnect: HostDisconnect is encoded into the RxEvent field of the RXCMD.
HostDisconnect is valid only when the ISP1507 is configured as a host (both
DP_PULLDOWN and DM_PULLDOWN are set to logic 1), and indicates to the host
controller when a peripheral is connected or disconnected. The host controller must
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
26 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
enable HostDisconnect by setting the HOST_DISCON_R and HOST_DISCON_F bits in
the USB_INTR_EN_R_E and USB_INTR_EN_F_E registers, respectively. Changes in
HostDisconnect will cause the PHY to send an RXCMD to the link with the updated value.
9.6 Register read and write operations
Figure 8 shows register read and write sequences. The ISP1507 supports immediate
addressing and extended addressing register operations. Extended register addressing is
optional for links. Note that register operations will be aborted if the ISP1507 unexpectedly
asserts DIR during the operation. When a register operation is aborted, the link must retry
until successful. For more information on register operations, refer to UTMI+ Low Pin
Interface (ULPI) Specification Rev. 1.1.
CLOCK
TXCMD
(REGW) D
TXCMD
(EXTW) AD D
TXCMD
(REGR)
D
TXCMD
(EXTW) AD
D
DATA[7:0]
immediate
register write
extended
register write
immediate
register read
extended
register read
DIR
STP
NXT
004aaa710
AD indicates the address byte, and D indicates the data byte.
Fig 8.
Example of register write, register read, extended register write and extended register read
9.7 USB reset and high-speed detection handshake (chirp)
Figure 9 shows the sequence of events for USB reset and high-speed detection
handshake (chirp). The sequence is shown for hosts and peripherals. Figure 9 does not
show all RXCMD updates and timing is not to scale. The sequence is as follows:
1. USB reset: The host detects a peripheral attachment as low-speed if DM is HIGH and
as full-speed if DP is HIGH. If a host detects a full-speed peripheral, it resets the
peripheral by writing to the Function Control register (see Section 10.1.2).
XCVRSELECT[1:0] = 00b (high-speed) and TERMSELECT = 0b are then set which
drives SE0 on the bus (DP and DM connected to ground through 45 Ω). The host also
sets OPMODE[1:0] = 10b for correct chirp transmit and receive. The start of SE0 is
labeled T0.
Remark: To receive chirp signaling, the host must also consider the high-speed
differential receiver output. The host controller must interpret LINESTATE[1:0] as
shown in Table 11.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
27 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
2. High-speed detection handshake (chirp)
a. Peripheral chirp: After detecting SE0 for no less than 2.5 µs, if the peripheral is
capable of high-speed, it sets XCVRSELECT[1:0] = 00b (high-speed) and
OPMODE[1:0] = 10b (chirp). The peripheral immediately follows this with a
TXCMD (NOPID), transmitting a Chirp K for no less than 1 ms and ending no more
than 7 ms after reset time T0. If the peripheral is in low-power mode, it must wake
up its clock within 5.6 ms, leaving 200 µs for the link to start transmitting the
Chirp K, and 1.2 ms for the Chirp K to complete (worst case with 10 % slow clock).
b. Host chirp: If the host does not detect the peripheral chirp, it must continue
asserting SE0 until the end of reset. If the host detects the peripheral Chirp K for
no less than 2.5 µs, then no more than 100 µs after the bus leaves the Chirp K
state, the host sends a TXCMD (NOPID) with an alternating sequence of Chirp Ks
and Js. Each Chirp K or Chirp J must last for no less than 40 µs and no longer than
60 µs.
c. High-speed idle: The peripheral must detect a minimum of Chirp K-J-K-J-K-J. Each
Chirp K and Chirp J must be detected for at least 2.5 µs. The peripheral sets
TERMSELECT = 0b and OPMODE[1:0] = 00b after seeing the minimum Chirp
sequence. The peripheral is now in high-speed mode and sees !squelch (01b on
LINESTATE). When the peripheral sees squelch (10b on LINESTATE), it knows
that the host has completed chirp and waits for Hi-Speed USB traffic to begin. After
transmitting the chirp sequence, the host changes OPMODE[1:0] to 00b and
begins sending USB packets.
For more information, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
28 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
USB reset
high-speed detection handshake (chirp)
T0
TXCMD
(REGW) SE0
K
HS idle
host chirp
peripheral chirp
00
TXCMD
NOPID K
...
J
K
J
TXCMD
(REGW)
DATA
[ 7:0]
DIR
ULPI host
STP
NXT
00 (HS)
01 (FS)
XCVR
SELECT
TERM
SELECT
00 (normal)
00 (normal)
01 (chirp)
OP
MODE
J (01b)
SE0 (00b)
peripheral chirp K (10b)
squelch
(00b)
host chirp K (10b) or chirp J (01b)
squelch (00b)
LINE
STATE
TXCMD
SE0 (REGW)
TXCMD
NOPID K
RXCMDs
K
...
K
00
K
J
K
J
K
TXCMD
J (REGW)
00
DATA
[ 7:0]
DIR
ULPI peripheral
STP
NXT
00 (HS)
01 (FS)
XCVR
SELECT
TERM
SELECT
00 (normal)
10 (chirp)
00 (normal)
OP
MODE
J (01b)
SE0 (00b)
peripheral chirp K (10b)
squelch
(00b)
host chirp K or J (10b or 01b)
!squelch
(01b) squelch (00b)
USB signals
LINE
STATE
DP
DM
004aaa711
Timing is not to scale.
Fig 9.
USB reset and high-speed detection handshake (chirp) sequence
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
29 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
9.8 USB packet transmit and receive
An example of a packet transmit and receive is shown in Figure 10. For details on USB
packets, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.
link sends
TXCMD
ISP1507
accepts
TXCMD
link sends
the next data;
ISP1507 link signals
accepts end of data
ISP1507
ISP1507
ISP1507
deasserts
asserts DIR, ISP1507
sends
sends
DIR, causing
causing
RXCMD
ULPI bus turnaround
USB data turnaround
(NXT LOW) (NXT HIGH)
is idle
cycle
cycle
CLOCK
DATA[ 7:0]
TXCMD
turnaround
DATA
RXCMD
DATA
turnaround
DIR
STP
NXT
004aab080
Fig 10. Example of using the ISP1507 to transmit and receive USB data
9.8.1 USB packet timing
9.8.1.1
ISP1507 pipeline delays
The ISP1507 delays are shown in Table 15. For a detailed description, refer to UTMI+ Low
Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.2.6.2.
Table 15.
PHY pipeline delays
Parameter name
High-speed PHY delay
Full-speed PHY delay
Low-speed PHY delay
RXCMD delay (J and K)
4
4
4
RXCMD delay (SE0)
4
4 to 6
16 to 18
TX start delay
1 to 2
6 to 10
74 to 75
TX end delay (packets)
3 to 4
not applicable
not applicable
TX end delay (SOF)
6 to 9
not applicable
not applicable
RX start delay
5 to 6
not applicable
not applicable
RX end delay
5 to 6
17 to 18
122 to 123
9.8.1.2
Allowed link decision time
The amount of clock cycles allocated to the link to respond to a received packet and
correctly receive back-to-back packets is given in Table 16. Link designs must follow
values given in Table 16 for correct USB system operation. Examples of high-speed
packet sequences and timing are shown in Figure 11 and Figure 12. For details, refer to
UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.2.6.3.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
30 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 16.
Link decision times
Packet sequence High-speed Full-speed
link delay
link delay
Low-speed
link delay
Definition
Transmit-Transmit
(host only)
77 to 247
Number of clock cycles a host link must wait before driving
the TXCMD for the second packet.
15 to 24
7 to 18
In high-speed, the link starts counting from the assertion of
STP for the first packet.
In full-speed, the link starts counting from the RXCMD,
indicating LINESTATE has changed from SE0 to J for the
first packet. The timing given ensures inter-packet delays of
2 bit times to 6.5 bit times.
Receive-Transmit
(host or
peripheral)
1 to 14
7 to 18
77 to 247
Number of clock cycles the link must wait before driving the
TXCMD for the transmit packet.
In high-speed, the link starts counting from the end of the
receive packet; deassertion of DIR or an RXCMD, indicating
RxActive is LOW.
In full-speed or low-speed, the link starts counting from the
RXCMD, indicating LINESTATE has changed from SE0 to J
for the receive packet. The timing given ensures
inter-packet delays of 2 bit times to 6.5 bit times.
Receive-Receive
(peripheral only)
1
1
1
Minimum number of clock cycles between consecutive
receive packets. The link must be able to receive both
packets.
Transmit-Receive
(host or
peripheral)
92
80
718
Host or peripheral transmits a packet and will time-out after
this number of clock cycles if a response is not received.
Any subsequent transmission can occur after this time.
USB interpacket delay (88 to 192 high-speed bit times)
DP or
DM
DATA
IDLE
EOP
SYNC
CLOCK
DN−1
DN
TXCMD
D0
D1
DATA
[7:0]
DIR
STP
NXT
link decision time (15 to 24 clocks)
TX end delay (two to five clocks)
TX start delay
(one to two clocks)
004aaa712
Fig 11. High-speed transmit-to-transmit packet timing
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
31 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
USB interpacket delay (8 to 192 high-speed bit times)
DP or
DM
IDLE
EOP
DATA
SYNC
CLOCK
DN
DN−2
DN−4
TXCMD
D0
D1
DATA
[7:0]
DN−3
DN−1
turnaround
DIR
STP
NXT
RX end delay
(three to eight clocks)
link decision time (1 to 14 clocks)
TX start delay
(one to two clocks)
004aaa713
Fig 12. High-speed receive-to-transmit packet timing
9.9 Preamble
Preamble packets are headers to low-speed packets that must travel over a full-speed
bus, between a host and a hub. To enter preamble mode, the link sets
XCVRSELECT[1:0] = 11b in the FUNC_CTRL register (see Section 10.1.2). When in
preamble mode, the ISP1507 operates just as in full-speed mode, and sends all data with
the full-speed rise time and fall time. Whenever the link transmits a USB packet in
preamble mode, the ISP1507 will automatically send a preamble header at full-speed bit
rate before sending the link packet at low-speed bit rate. The ISP1507 will ensure a
minimum gap of four full-speed bit times between the last bit of the full-speed PRE PID
and the first bit of the low-speed packet SYNC. The ISP1507 will drive a J for at least one
full-speed bit time after sending the PRE PID, after which the pull-up resistor can hold the
J state on the bus. An example transmit packet is shown in Figure 13.
In preamble mode, the ISP1507 can also receive low-speed packets from the full-speed
bus.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
32 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
CLOCK
DATA[7:0]
TXCMD (low-speed packet ID)
D0
D1
DIR
STP
NXT
DP or DM
FS SYNC
FS
PRE ID
IDLE (min
4 FS bits)
LS SYNC
LS PID
LS D0
LS D1
004aaa714
DP and DM timing is not to scale.
Fig 13. Preamble sequence
9.10 USB suspend and resume
9.10.1 Full-speed and low-speed host-initiated suspend and resume
Figure 14 illustrates how a host or a hub places a full-speed or low-speed peripheral into
suspend and sometime later initiates resume signaling to wake up the downstream
peripheral. Note that Figure 14 timing is not to scale, and does not show all RXCMD
LINESTATE updates.
The sequence of events for a host and a peripheral, both with ISP1507, is as follows:
1. Idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ pull-down
resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b) and 45 Ω
terminations disabled (TERMSELECT is set to 1b). The peripheral has the 1.5 kΩ
pull-up resistor connected to DP for full-speed or DM for low-speed (TERMSELECT is
set to 1b).
2. Suspend: When the peripheral sees no bus activity for 3 ms, it enters the suspend
state. The peripheral link places the PHY into low-power mode by clearing the
SUSPENDM bit in the FUNC_CTRL register (see Section 10.1.2), causing the PHY to
draw only suspend current. The host may or may not be powered down.
3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE[1:0] to
10b and transmits a K for at least 20 ms. The peripheral link sees the resume K on
LINESTATE, and asserts STP to wake up the PHY.
4. EOP: When STP is asserted, the ISP1507 on the host side automatically appends an
EOP of two bits of SE0 at low-speed bit rate, followed by one bit of J. The ISP1507 on
the host side knows to add the EOP because DP_PULLDOWN and DM_PULLDOWN
are set to 1b for a host. After the EOP is completed, the host link sets OPMODE[1:0]
to 00b for normal operation. The peripheral link sees the EOP and also resumes
normal operation.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
33 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
suspend
idle
FS or LS host (XCVRSELECT = 01b (FS)
or 10b (LS), DP_PULLDOWN = 1b,
DM_PULLDOWN = 1b, TERMSELECT = 1b)
TXCMD
(REGW)
EOP
resume K
TXCMD
NOPID
K
K
...
idle
TXCMD
K
DATA
[7:0]
DIR
STP
NXT
OPMODE
10b
00b
LINE
STATE
K
J
00b
J
SE0
FS or LS peripheral (XCVRSELECT = 01b (FS)
or 10b (LS), DP_PULLDOWN = 0b, TERMSELECT = 1b)
CLOCK
TXCMD
(REGW)
LINESTATE J
LINESTATE K
SE0
J
DATA
[7:0]
DIR
STP
NXT
OPMODE
00b
10b
00b
SUSPENDM
USB signals
(only FS is shown)
LINE
STATE
K
J
SE0
J
DP
DM
004aab123
Timing is not to scale.
Fig 14. Full-speed suspend and resume
9.10.2 High-speed suspend and resume
Figure 15 illustrates how a host or a hub places a high-speed enabled peripheral into
suspend and then initiates resume signaling. The high-speed peripheral will wake up and
return to high-speed operations. Note that Figure 15 timing is not to scale, and does not
show all RXCMD LINESTATE updates.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
34 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
The sequence of events related to a host and a peripheral, both with ISP1507, is as
follows:
1. High-speed idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ
pull-down resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b)
and 45 Ω terminations enabled (TERMSELECT is set to 0b). The peripheral has its
45 Ω terminations enabled (TERMSELECT is set to 0b).
2. Full-speed suspend: When the peripheral sees no bus activity for 3 ms, it enters the
suspend state. The peripheral link places the ISP1507 into full-speed mode
(XCVRSELECT is set to 01b), removes 45 Ω terminations, and enables the 1.5 kΩ
pull-up resistor on DP (TERMSELECT is set to 1b). The peripheral link then places
the ISP1507 into low-power mode by clearing SUSPENDM, causing the ISP1507 to
draw only suspend current. The host also changes the ISP1507 to full-speed
(XCVRSELECT is set to 01b), removes 45 Ω terminations (TERMSELECT is set to
1b), and then may or may not be powered down.
3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE to 10b
and transmits a full-speed K for at least 20 ms. The peripheral link sees the resume K
(10b) on LINESTATE, and asserts STP to wake up the ISP1507.
4. High-speed traffic: The host link sets high-speed (XCVRSELECT is set to 00b) and
enables its 45 Ω terminations (TERMSELECT is set to 0b). The peripheral link sees
SE0 on LINESTATE and also sets high-speed (XCVRSELECT is set to 00b), and
enables its 45 Ω terminations (TERMSELECT is set to 0b). The host link sets
OPMODE to 00b for normal high-speed operation.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
35 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
FS suspend
HS idle
resume K
TXCMD TXCMD
(REGW) NOPID K K
TXCMD
(REGW)
HS idle
TXCMD
... K (REGW)
ULPI HS host (DP_PULLDOWN = 1b,
DM_PULLDOWN = 1b)
DATA
[7:0]
DIR
STP
NXT
XCVR
SELECT
01b
00b
00b
TERM
SELECT
OP
MODE
!SQUELCH SQUELCH
(00b)
(01b)
LINE
STATE
10b
00b
00b
FS K (10b)
FS J (01b)
SQUELCH (00b)
!SQUELCH
(01b)
CLOCK
TXCMD
(REGW)
TXCMD
SE0 (REGW)
LINESTATE K
LINESTATE J
ULPI HS peripheral (DP_PULLDOWN = 0b)
DATA
[7:0]
DIR
STP
NXT
XCVR
SELECT
01b
00b
00b
TERM
SELECT
OP
MODE
00b
10b
00b
SUSPENDM
USB signals
LINE
STATE
!SQUELCH SQUELCH
(01b)
(00b)
FS J (01b)
FS K (10b)
SQUELCH (00b)
!SQUELCH
(01b)
DP
DM
004aab124
Timing is not to scale.
Fig 15. High-speed suspend and resume
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
36 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
9.10.3 Remote wake-up
The ISP1507 supports peripherals that initiate remote wake-up resume. When placed into
USB suspend, the peripheral link remembers at what speed it was originally operating.
Depending on the original speed, the link follows one of the protocols detailed here. In
Figure 16, timing is not to scale, and not all RXCMD LINESTATE updates are shown.
The sequence of events related to a host and a peripheral, both with ISP1507, is as
follows:
1. Both the host and the peripheral are assumed to be in low-power mode.
2. The peripheral begins remote wake-up by re-enabling its clock and setting its
SUSPENDM bit to 1b.
3. The peripheral begins driving K on the bus to signal resume. Note that the peripheral
link must assume that LINESTATE is K (01b) while transmitting because it will not
receive any RXCMDs.
4. The host recognizes the resume, re-enables its clock and sets its SUSPENDM bit.
5. The host takes over resume driving within 1 ms of detecting the remote wake-up.
6. The peripheral stops driving resume.
7. The peripheral sees the host continuing to drive resume.
8. The host stops driving resume and the ISP1507 automatically adds the EOP to the
end of resume. The peripheral recognizes the EOP as the end of resume.
9. Both the host and the peripheral revert to normal operation by writing 00b to
OPMODE. If the host or the peripheral was previously in high-speed mode, it must
revert to high-speed before the SE0 of the EOP is completed. This can be achieved
by writing XCVRSELECT[1:0] = 00b and TERMSELECT = 0b after LINESTATE
indicates SE0.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
37 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
TXCMD
REGW
LINESTATE
TXCMD
NOPID
TXCMD
REGW
00h
DATA
[ 7:0]
ULPI host
DIR
STP
NXT
XCVR
SELECT
00b (HS only)
01b (FS), 10b (LS)
TERM
SELECT
0b (HS only)
OP
MODE
00b
10b
LINESTATE
TXCMD
REGW
TXCMD
NOPID
RXCMD
00h
RXCMD
TXCMD
RXCMD REGW
DATA
[ 7:0]
ULPI peripheral
DIR
STP
NXT
00b (HS only)
XCVR
SELECT
00b (HS), 01b (FS), 10b (LS)
TERM
SELECT
0b (HS only)
OP
MODE
10b
00b
004aaa718
Timing is not to scale.
Fig 16. Remote wake-up from low-power mode
9.11 No automatic SYNC and EOP generation (optional)
This setting allows the link to turn off the automatic SYNC and EOP generation, and must
be used for high-speed packets only. It is provided for backward compatibility with legacy
controllers that include SYNC and EOP bytes in the data payload when transmitting
packets. The ISP1507 will not automatically generate the SYNC and EOP patterns when
OPMODE[1:0] is set to 11b. The ISP1507 will still NRZI encode data and perform bit
stuffing. An example of a sequence is shown in Figure 17. The link must always send
packets using the TXCMD (NOPID) type. The ISP1507 does not provide a mechanism to
control bit stuffing in individual bytes, but will automatically turn off bit stuffing for EOP
when STP is asserted with data set to FEh. If data is set to 00h when STP is asserted, the
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
38 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
PHY will not transmit any EOP. The ISP1507 will also detect if the PID byte is A5h,
indicating an SOF packet, and automatically send a long EOP when STP is asserted. To
transmit chirp and resume signaling, the link must set OPMODE[1:0] to 10b.
CLOCK
ULPI signals
TXCMD
00h
00h 00h 80h PID
D1
D2
D3
...
... D
N − 1 DN
FEh
DATA
[7:0]
DIR
STP
USB bus
UTMI+ equivalent
signals
NXT
TXVALID
TXREADY
TXBIT
STUFF
ENABLE
IDLE
SYNC
PID
DATA PAYLOAD
EOP
IDLE
DP, DM
004aab125
Fig 17. Transmitting USB packets without the automatic SYNC and EOP generation
9.12 On-The-Go operations
On-The-Go (OTG) is a supplement to Universal Serial Bus Specification Rev. 2.0 that
allows a portable USB device to assume the role of a limited USB host by defining
improvements, such as a small connector and low power. Non-portable devices, such as
standard hosts and embedded hosts, can also benefit from OTG features.
The ISP1507 OTG PHY is designed to support all the tasks specified in the OTG
supplement. The ISP1507 provides the front-end analog support for Host Negotiation
Protocol (HNP) and Session Request Protocol (SRP) for dual-role devices. The
supporting components include:
• Voltage comparators
– A_VBUS_VLD
– SESS_VLD (session valid, can be used for both A-session and B-session valid)
– SESS_END (session end)
• Pull-up and pull-down resistors on DP and DM
• Charge and discharge resistors on VBUS
For complete OTG support, the system designer must add a VBUS power supply and
detect the value on the ID pin of the USB cable. This is not provided on the ISP1507.
The following subsections describe how to use the ISP1507 OTG components.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
39 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
9.12.1 OTG comparators
The ISP1507 provides comparators that conform to On-The-Go Supplement to the
USB 2.0 Specification Rev. 1.3 requirements of VA_VBUS_VLD, VA_SESS_VLD, VB_SESS_VLD
and VB_SESS_END. In this data sheet, VA_SESS_VLD and VB_SESS_VLD are combined into
VB_SESS_VLD. Comparators are described in Section 7.6. Changes in comparator values
are communicated to the link by RXCMDs as described in Section 9.5.2.2. Control over
comparators is described in Section 10.1.5 to Section 10.1.8.
9.12.2 Pull-up and pull-down resistors
The USB resistors on DP and DM can be used to initiate data-line pulsing SRP. The link
must set the required bus state using mode settings given in Table 7.
9.12.3 VBUS charge and discharge resistors
A pull-up resistor, RUP(VBUS), is provided to perform VBUS pulsing SRP. A B-device is
allowed to charge VBUS above the session valid threshold to request the host to turn on
the VBUS power.
A pull-down resistor, RDN(VBUS), is provided for a B-device to discharge VBUS. This is done
whenever the A-device turns off the VBUS power. The B-device can use the pull-down
resistor to ensure VBUS is below VB_SESS_END before starting a session.
For details, refer to On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3.
9.13 Serial modes
The ISP1507 supports both 6-pin serial mode and 3-pin serial mode, controlled by
bits 6PIN_FSLS_SERIAL and 3PIN_FSLS_SERIAL of the INTF_CTRL register (see
Section 10.1.3). For details, refer to UTMI+ Low Pin Interface (ULPI) Specification
Rev. 1.1, Section 3.10.
Figure 18 and Figure 19 provide examples of 6-pin serial mode and 3-pin serial mode,
respectively.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
40 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
TRANSMIT
SYNC
DATA
RECEIVE
EOP
SYNC
DATA
EOP
DATA0
(TX_ENABLE)
DATA1
(TX_DAT)
DATA2
(TX_SE0)
DATA4
(RX_DP)
DATA5
(RX_DM)
DATA6
(RX_RCV)
DP
DM
004aaa692
Fig 18. Example of transmit followed by receive in 6-pin serial mode
TRANSMIT
SYNC
DATA
RECEIVE
EOP
SYNC
DATA
EOP
DATA0
(TX_ENABLE)
DATA1
(TX_DAT/
RX_RCV)
DATA2
(TX_SE0/
RX_SE0)
DP
DM
004aaa693
Fig 19. Example of transmit followed by receive in 3-pin serial mode
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
41 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
9.14 Aborting transfers
The ISP1507 supports aborting transfers on the ULPI bus. For details, refer to UTMI+ Low
Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.4.
9.15 Avoiding contention on the ULPI data bus
Because the ULPI data bus is bidirectional, avoid situations in which both the link and the
PHY simultaneously drive the data bus.
The following points must be considered while implementing the data bus drive control on
the link.
After power-up and clock stabilization, default states are as follows:
• The ISP1507 drives DIR to LOW.
• The data bus is input to the ISP1507.
• The ULPI link data bus is output, with all data bus lines driven to LOW.
When the ISP1507 wants to take control of the data bus to initiate a data transfer, it
changes the DIR value from LOW to HIGH.
At this point, the link must disable its output buffers. This must be as fast as possible so
the link must use a combinational path from DIR.
The ISP1507 will not immediately enable its output buffers, but will delay the enabling of
its buffers until the next clock edge, avoiding bus contention.
When the data transfer is no longer required by the ISP1507, it changes DIR from HIGH to
LOW and starts to immediately turn off its output drivers. The link senses the change of
DIR from HIGH to LOW, but delays enabling its output buffers for one CLOCK cycle,
avoiding data bus contention.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
42 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10. Register map
Table 17.
Immediate register set overview
Field name
Size
(bit)
Address (6 bit)
R[1]
W[2]
S[3]
C[4]
References
VENDOR_ID_LOW
8
00h
-
-
-
VENDOR_ID_HIGH
8
01h
-
-
-
PRODUCT_ID_LOW
8
02h
-
-
-
PRODUCT_ID_HIGH
8
03h
-
-
-
FUNC_CTRL
8
04h to 06h
04h
05h
06h
Section 10.1.2 on page 44
INTF_CTRL
8
07h to 09h
07h
08h
09h
Section 10.1.3 on page 45
OTG_CTRL
8
0Ah to 0Ch
0Ah
0Bh
0Ch
Section 10.1.4 on page 47
USB_INTR_EN_R_E
8
0Dh to 0Fh
0Dh
0Eh
0Fh
Section 10.1.5 on page 47
USB_INTR_EN_F_E
8
10h to 12h
10h
11h
12h
Section 10.1.6 on page 48
USB_INTR_STAT
8
13h
-
-
-
Section 10.1.7 on page 49
USB_INTR_L
8
14h
-
-
-
Section 10.1.8 on page 49
DEBUG
8
15h
-
-
-
Section 10.1.9 on page 50
SCRATCH
8
16h to 18h
16h
17h
18h
Section 10.1.10 on page 50
-
2Fh
Section 10.1.1 on page 44
Section 10.1.11 on page 50
Reserved (do not use)
-
Access extended register set
8
19h to 2Eh
Vendor-specific registers
8
30h to 3Ch
Section 10.1.13 on page 50
PWR_CTRL
8
3Dh to 3Fh
Section 10.1.14 on page 50
-
-
Section 10.1.12 on page 50
[1]
Read (R): A register can be read. Read-only if this is the only mode given.
[2]
Write (W): The pattern on the data bus will be written over all bits of a register.
[3]
Set (S): The pattern on the data bus is OR-ed with and written to a register.
[4]
Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero
(cleared).
Table 18.
Extended register set overview
Field name
Size
(bit)
Address (6 bit)
R[1]
References
W[2]
S[3]
Maps to immediate register set above 8
00h to 3Fh
Reserved (do not use)
40h to FFh
8
C[4]
Section 10.2 on page 51
[1]
Read (R): A register can be read. Read-only if this is the only mode given.
[2]
Write (W): The pattern on the data bus will be written over all bits of a register.
[3]
Set (S): The pattern on the data bus is OR-ed with and written to a register.
[4]
Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero
(cleared).
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
43 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10.1 Immediate register set
10.1.1 Vendor ID and Product ID registers
10.1.1.1
VENDOR_ID_LOW register
Table 19 shows the bit description of the register.
Table 19.
VENDOR_ID_LOW - Vendor ID Low register (address R = 00h) bit description
Bit
Symbol
Access Value
Description
7 to 0
VENDOR_ID_
LOW[7:0]
R
Vendor ID Low: Lower byte of the NXP vendor ID supplied by USB-IF; has
a fixed value of CCh
10.1.1.2
CCh
VENDOR_ID_HIGH register
The bit description of the register is given in Table 20.
Table 20.
VENDOR_ID_HIGH - Vendor ID High register (address R = 01h) bit description
Bit
Symbol
Access
Value
Description
7 to 0
VENDOR_ID_
HIGH[7:0]
R
04h
Vendor ID High: Upper byte of the NXP vendor ID supplied by USB-IF;
has a fixed value of 04h
10.1.1.3
PRODUCT_ID_LOW register
The bit description of the PRODUCT_ID_LOW register is given in Table 21.
Table 21.
PRODUCT_ID_LOW - Product ID Low register (address R = 02h) bit description
Bit
Symbol
7 to 0
PRODUCT_ID_ R
LOW[7:0]
Access
10.1.1.4
Value
Description
05h
Product ID Low: Lower byte of the NXP product ID number; has a fixed
value of 05h
PRODUCT_ID_HIGH register
The bit description of the register is given in Table 22.
Table 22.
PRODUCT_ID_HIGH - Product ID High register (address R = 03h) bit description
Bit
Symbol
7 to 0
PRODUCT_ID_ R
HIGH[7:0]
Access
Value
Description
15h
Product ID High: Upper byte of the NXP product ID number; has a
fixed value of 15h
10.1.2 FUNC_CTRL register
This register controls UTMI function settings of the PHY. The bit allocation of the register
is given in Table 23.
Table 23.
FUNC_CTRL - Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit allocation
Bit
Symbol
7
6
5
reserved
SUSPENDM
RESET
Reset
Access
4
3
OPMODE[1:0]
2
TERM
SELECT
1
0
XCVRSELECT[1:0]
0
1
0
0
0
0
0
1
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
44 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 24.
FUNC_CTRL - Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit
description
Bit
Symbol
Description
7
-
reserved
6
SUSPENDM
Suspend LOW: Active LOW PHY suspend.
Places the PHY into low-power mode. The PHY will power down all blocks, except the
full-speed receiver, OTG comparators and ULPI pins.
To come out of low-power mode, the link must assert STP. The PHY will automatically clear
this bit when it exits low-power mode.
0b — Low-power mode
1b — Powered (default)
5
RESET
Reset: Active HIGH transceiver reset.
After the link sets this bit, the PHY will assert DIR and reset the digital core. This does not
reset the ULPI interface or the ULPI register set.
When reset is completed, the PHY will deassert DIR and automatically clear this bit, followed
by an RXCMD update to the link.
0b — Do not reset (default)
1b — Reset
The link must wait for DIR to deassert before using the ULPI bus. Does not reset the ULPI
interface or the ULPI register set.
4 to 3
OPMODE[1:0]
Operation Mode: Selects the required bit-encoding style during transmit.
00b — Normal operation (default)
01b — Non-driving
10b — Disable bit-stuffing and NRZI encoding
11b — Do not automatically add SYNC and EOP when transmitting; must be used only for
high-speed packets
2
TERMSELECT
Termination Select: Controls the internal 1.5 kΩ full-speed pull-up resistor and 45 Ω
high-speed terminations. Control over bus resistors changes, depending on
XCVRSELECT[1:0], OPMODE[1:0], DP_PULLDOWN and DM_PULLDOWN, as shown in
Table 7.
1 to 0
XCVRSELECT[1:0]
Transceiver Select: Selects the required transceiver speed.
00b — Enable the high-speed transceiver
01b — Enable the full-speed transceiver
10b — Enable the low-speed transceiver
11b — Enable the full-speed transceiver for low-speed packets (full-speed preamble is
automatically prefixed)
10.1.3 INTF_CTRL register
The INTF_CTRL register enables alternative interfaces. All of these modes are optional
features provided for legacy link cores. Setting more than one of these fields results in
undefined behavior. Table 25 provides the bit allocation of the register.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
45 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 25.
INTF_CTRL - Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit allocation
Bit
Symbol
7
6
5
4
3
2
INTF_
PROT_DIS
IND_PASS
THRU
IND_
COMPL
reserved
CLOCK_
SUSPENDM
reserved
0
0
0
0
0
0
0
0
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
Reset
Access
Table 26.
1
0
3PIN_FSLS 6PIN_FSLS
_SERIAL
_SERIAL
INTF_CTRL - Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit
description
Bit
Symbol
Description
7
INTF_PROT_DIS
Interface Protect Disable: Controls circuitry built into the ISP1507 to protect the ULPI
when the link 3-states STP and DATA[7:0]. When this bit is enabled, the ISP1507 will
automatically detect when the link stops driving STP.
0b — Enables the interface protect circuit (default). The ISP1507 attaches a weak pull-up
resistor on STP. If STP is unexpectedly HIGH, the ISP1507 attaches weak pull-down
resistors on DATA[7:0], protecting data inputs.
1b — Disables the interface protect circuit, detaches weak pull-down resistors on
DATA[7:0], and a weak pull-up resistor on STP.
6
IND_PASSTHRU
Indicator Pass-through: The ISP1507 does not support the qualification of an external
FAULT with the internal VA_VBUS_VLD comparator. Either a digital FAULT is input on the
VBUS/FAULT pin or the VBUS power is connected to the VBUS/FAULT pin, not both. This bit
must always be set to logic 1.
0b — Not supported.
1b — The complement output signal is not qualified with the internal A_VBUS_VLD
comparator. The link must always set this bit to logic 1.
5
IND_COMPL
Indicator Complement: Informs the PHY to invert the FAULT input signal, generating the
complement output. For details, see Section 9.5.2.2.
0b — The ISP1507 will not invert the FAULT signal (default).
1b — The ISP1507 will invert the FAULT signal.
4
-
reserved
3
CLOCK_SUSPENDM
Clock Suspend LOW: Active LOW clock suspend.
Powers down the internal clock circuitry only. By default, the clock will not be powered in
6-pin serial mode or 3-pin serial mode.
Valid only in 6-pin serial mode and 3-pin serial mode. Valid only when SUSPENDM is set to
logic 1, otherwise this bit is ignored.
0b — Clock will not be powered in 3-pin or 6-pin serial mode.
1b — Clock will be powered in 3-pin and 6-pin serial modes.
2
-
reserved
1
3PIN_FSLS_SERIAL
3-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI to a 3-bit serial interface.
The PHY will automatically clear this bit when 3-pin serial mode is exited.
0b — Full-speed or low-speed packets are sent using the parallel interface.
1b — Full-speed or low-speed packets are sent using the 3-pin serial interface.
0
6PIN_FSLS_SERIAL
6-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI to a 6-bit serial interface.
The PHY will automatically clear this bit when 6-pin serial mode is exited.
0b — Full-speed or low-speed packets are sent using the parallel interface.
1b — Full-speed or low-speed packets are sent using the 6-pin serial interface.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
46 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10.1.4 OTG_CTRL register
This register controls various OTG functions of the ISP1507. The bit allocation of the
OTG_CTRL register is given in Table 27.
Table 27.
OTG_CTRL - OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit allocation
Bit
7
Symbol
Reset
Access
Table 28.
6
USE_EXT_
DRV_
VBUS_IND VBUS_EXT
5
4
3
2
1
0
DRV_
VBUS
CHRG_
VBUS
DISCHRG_
VBUS
DM_PULL
DOWN
DP_PULL
DOWN
reserved
0
0
0
0
0
1
1
0
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
OTG_CTRL - OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit description
Bit
Symbol
Description
7
USE_EXT_
VBUS_IND
Use External VBUS Indicator: Informs the PHY to use an external VBUS overcurrent indicator.
0b — Use the internal OTG comparator.
1b — Use the external VBUS valid indicator signal input from the FAULT pin.
6
DRV_VBUS_EXT
Drive VBUS External: Controls the external VBUS supply through the RESET_N/PSW_N pin.
0b — Do not drive PSW_N to LOW, disabling VBUS.
1b — Drive PSW_N to LOW, enabling VBUS.
5
DRV_VBUS
Drive VBUS: Signals the ISP1507 to drive 5 V on VBUS. If DRV_VBUS_EXT is set to logic 1,
then setting DRV_VBUS is optional.
4
CHRG_VBUS
Charge VBUS: Charges VBUS through a resistor. Used for the VBUS pulsing SRP. The link must
first check that VBUS is discharged (see the DISCHRG_VBUS bit), and that both the DP and
DM data lines have been LOW (SE0) for 2 ms.
0b — Do not charge VBUS.
1b — Charge VBUS.
3
DISCHRG_VBUS
Discharge VBUS: Discharges VBUS through a resistor. If the link sets this bit to logic 1, it waits
for an RXCMD indicating that SESS_END has changed from 0 to 1, and then resets this bit to 0
to stop the discharge.
0b — Do not discharge VBUS.
1b — Discharge VBUS.
2
DM_PULLDOWN
DM Pull Down: Enables the 15 kΩ pull-down resistor on DM.
0b — Pull-down resistor is not connected to DM.
1b — Pull-down resistor is connected to DM.
1
DP_PULLDOWN
DP Pull Down: Enables the 15 kΩ pull-down resistor on DP.
0b — Pull-down resistor is not connected to DP.
1b — Pull-down resistor is connected to DP.
0
-
reserved; writing logic 1 will give undefined results
10.1.5 USB_INTR_EN_R_E register
The bits in this register enable interrupts and RXCMDs to be sent when the corresponding
bits in the USB_INTR_STAT register change from logic 0 to logic 1. By default, all
transitions are enabled. Table 29 shows the bit allocation of the register.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
47 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 29.
USB_INTR_EN_R_E - USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh,
S = 0Eh, C = 0Fh) bit allocation
Bit
7
6
Symbol
5
4
reserved
Reset
Access
Table 30.
3
2
1
0
SESS_
END_R
SESS_
VALID_R
VBUS_
VALID_R
HOST_
DISCON_R
0
0
0
1
1
1
1
1
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
USB_INTR_EN_R_E - USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh,
S = 0Eh, C = 0Fh) bit description
Bit
Symbol
Description
7 to 4
-
reserved
3
SESS_END_R
Session End Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on
SESS_END.
2
SESS_VALID_R
Session Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on
SESS_VLD.
1
VBUS_VALID_R
VBUS Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on
A_VBUS_VLD.
0
HOST_DISCON_R Host Disconnect Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on
HOST_DISCON.
10.1.6 USB_INTR_EN_F_E register
The bits in this register enable interrupts and RXCMDs to be sent when the corresponding
bits in the USB_INTR_STAT register change from logic 1 to logic 0. By default, all
transitions are enabled. See Table 31.
Table 31.
USB_INTR_EN_F_E - USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h,
S = 11h, C = 12h) bit allocation
Bit
7
6
Symbol
5
4
reserved
Reset
Access
Table 32.
3
2
1
0
SESS_
END_F
SESS_
VALID_F
VBUS_
VALID_F
HOST_
DISCON_F
0
0
0
1
1
1
1
1
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
USB_INTR_EN_F_E - USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h,
S = 11h, C = 12h) bit description
Bit
Symbol
Description
7 to 4
-
reserved
3
SESS_END_F
Session End Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on
SESS_END.
2
SESS_VALID_F
Session Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on
SESS_VLD.
1
VBUS_VALID_F
VBUS Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on
A_VBUS_VLD.
0
HOST_DISCON_F Host Disconnect Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on
HOST_DISCON.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
48 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10.1.7 USB_INTR_STAT register
This register (see Table 33) indicates the current value of the interrupt source signal.
Table 33.
USB_INTR_STAT - USB Interrupt Status register (address R = 13h) bit allocation
Bit
7
6
Symbol
5
4
reserved
3
2
1
0
SESS_
END
SESS_
VALID
VBUS_
VALID
HOST_
DISCON
Reset
X
X
X
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Table 34.
USB_INTR_STAT - USB Interrupt Status register (address R = 13h) bit description
Bit
Symbol
Description
7 to 4
-
reserved
3
SESS_END
Session End: Reflects the current value of the session end voltage comparator.
2
SESS_VALID
Session Valid: Reflects the current value of the session valid voltage comparator.
1
VBUS_VALID
VBUS Valid: Reflects the current value of the VBUS valid voltage comparator.
0
HOST_DISCON
Host Disconnect: Reflects the current value of the host disconnect detector.
10.1.8 USB_INTR_L register
The bits of the USB_INTR_L register are automatically set by the ISP1507 when an
unmasked change occurs on the corresponding interrupt source signal. The ISP1507 will
automatically clear all bits when the link reads this register, or when the PHY enters
low-power mode.
Remark: It is optional for the link to read this register when the clock is running because
all signal information will automatically be sent to the link through the RXCMD byte.
The bit allocation of this register is given in Table 35.
Table 35.
USB_INTR_L - USB Interrupt Latch register (address R = 14h) bit allocation
Bit
7
6
Symbol
5
4
reserved
3
2
1
0
SESS_
END_L
SESS_
VALID_L
VBUS_
VALID_L
HOST_
DISCON_L
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Table 36.
USB_INTR_L - USB Interrupt Latch register (address R = 14h) bit description
Bit
Symbol
Description
7 to 4
-
reserved
3
SESS_END_L
Session End Latch: Automatically set when an unmasked event occurs on SESS_END.
Cleared when this register is read.
2
SESS_VALID_L
Session Valid Latch: Automatically set when an unmasked event occurs on SESS_VLD.
Cleared when this register is read.
1
VBUS_VALID_L
VBUS Valid Latch: Automatically set when an unmasked event occurs on A_VBUS_VLD.
Cleared when this register is read.
0
HOST_DISCON_L
Host Disconnect Latch: Automatically set when an unmasked event occurs on
HOST_DISCON. Cleared when this register is read.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
49 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10.1.9 DEBUG register
The bit allocation of the DEBUG register is given in Table 37. This register indicates the
current value of signals useful for debugging.
Table 37.
DEBUG - Debug register (address R = 15h) bit allocation
Bit
7
6
5
Symbol
4
3
2
reserved
1
0
LINE
STATE1
LINE
STATE0
Reset
0
0
0
0
0
0
0
0
Access
R
R
R
R
R
R
R
R
Table 38.
DEBUG - Debug register (address R = 15h) bit description
Bit
Symbol
Description
7 to 2
-
reserved
1
LINESTATE1
Line State 1: Contains the current value of LINESTATE 1
0
LINESTATE0
Line State 0: Contains the current value of LINESTATE 0
10.1.10 SCRATCH register
Table 39 shows the bit description of the SCRATCH register. It is an empty register for
testing purposes.
Table 39.
SCRATCH - Scratch register (address R = 16h to 18h, W = 16h, S = 17h, C = 18h) bit description
Bit
Symbol
Access
Value
Description
7 to 0
SCRATCH
[7:0]
R/W/S/C
00h
Scratch: This is an empty register byte for testing purposes. Software
can read, write, set and clear this register. The functionality of the PHY
will not be affected.
10.1.11 Reserved
Registers 19h to 2Eh are not implemented. Operating on these addresses will have no
effect on the PHY.
10.1.12 Access extended register set
Address 2Fh does not contain register data. Instead it links to the extended register set.
The immediate register set maps to the lower end of the extended register set.
10.1.13 Vendor-specific registers
Addresses 30h to 3Fh contain vendor-specific registers.
10.1.14 PWR_CTRL register
Table 40 provides the bit allocation of the PWR_CTRL register.
Table 40.
PWR_CTRL - Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit allocation
Bit
7
6
Symbol
4
reserved
Reset
Access
5
3
2
1
0
BVALID_
FALL
BVALID_
RISE
reserved
IGNORE_
RESET
0
0
0
0
0
0
0
0
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
R/W/S/C
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
50 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 41.
PWR_CTRL - Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description
Bit
Symbol
Description
7 to 4
-
reserved; the link must never write logic 1 to these bits.
3
BVALID_FALL
BVALID Fall: Enables RXCMDs for HIGH-to-LOW transitions on BVALID. When BVALID
changes from HIGH to LOW, the ISP1507 will send an RXCMD to the link with the ALT_INT
bit set to logic 1.
This bit is optional and is not necessary for OTG devices. This bit is provided for debugging
purposes. The session valid comparator must be used instead.
2
BVALID_RISE
BVALID Rise: Enables RXCMDs for LOW-to-HIGH transitions on BVALID. When BVALID
changes from LOW to HIGH, the ISP1507 will send an RXCMD to the link with the ALT_INT
bit set to logic 1.
This bit is optional and is not necessary for OTG devices. This bit is provided for debugging
purposes. The session valid comparator must be used instead.
1
-
reserved
0
IGNORE_RESET
Ignore Reset: Selects between the RESET_N and PSW_N functions of the
RESET_N/PSW_N pin. The link must set this bit to logic 1, if PSW_N is used in a ganged
mode configuration.
0b — The RESET_N/PSW_N pin behaves as an active-LOW reset input (RESET_N). This is
the default setting.
1b — The RESET_N/PSW_N pin behaves as an active-LOW power switch output (PSW_N).
10.2 Extended register set
Addresses 00h to 3Fh of the extended register set directly map to the immediate set. This
means a read, write, set or clear operation to these extended addresses will operate on
the immediate register set.
Addresses 40h to FFh are not implemented. Operating on these addresses may result in
undefined behavior of the PHY.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
51 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
11. ElectroStatic Discharge (ESD)
11.1 ESD protection
The pins that are connected to the USB connector (DP, DM, VBUS and GND) have a
minimum of ±4 kV ESD protection. Capacitors 0.1 µF and 1 µF must be connected in
parallel from VBUS to GND to achieve this ±4 kV ESD protection (see Figure 20).
Remark: Capacitors 0.1 µF and 1 µF are also required by Universal Serial Bus
Specification Rev. 2.0. For details on the requirements for CVBUS, see Section 16.
RC
1 MΩ
RD
1500 Ω
charge current
limit resistor
discharge
resistance
DEVICE UNDER
TEST
VBUS
A
HIGH VOLTAGE
DC SOURCE
CS
100 pF
storage
capacitor
B
0.1 µF
1 µF
GND
004aaa881
Fig 20. Human body ESD test model
11.2 ESD test conditions
A detailed report on test setup and results is available on request.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
52 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
12. Limiting values
Table 42. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
VCC
supply voltage
VCC(I/O)
input/output supply voltage
VI
input voltage
Conditions
Min
Max
Unit
−0.5
+4.6
V
−0.5
+4.6
V
on pins STP, DATA[7:0] and
RESET_N/PSW_N
−0.5
VCC(I/O) + 0.5
V
on pin VBUS/FAULT
−0.5
+6.0
V
−0.5
+2.5
V
on pins DP and DM
[1]
−0.5
+4.6
V
on pins DP, DM, VBUS and GND;
ILI < 1 µA
[2]
−4
+4
kV
on pin XTAL1
VESD
electrostatic discharge
voltage
−2
+2
kV
Ilu
latch-up current
−100
+100
mA
Vlu
latch-up voltage
-
4.6
V
Tstg
storage temperature
−40
+125
°C
on all other pins; ILI < 1 µA
[1]
The ISP1507 has been tested according to the additional requirements listed in Universal Serial Bus Specification Rev. 2.0,
Section 7.1.1. The short circuit withstand test and the AC stress test were performed for 24 hours, and the ISP1507 was found to be fully
operational after the test completed.
[2]
Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor (Human Body Model JESD22-A114D).
13. Recommended operating conditions
Table 43.
Recommended operating conditions
Symbol
Parameter
VCC
supply voltage
VCC(I/O)
input/output supply voltage
VI
input voltage
Conditions
Min
Typ
Max
Unit
3.0
3.3
3.6
V
1.65
-
3.6
V
on pins STP, DATA[7:0] and
RESET_N/PSW_N
0
-
VCC(I/O)
V
on pin VBUS/FAULT
0
-
5.5
V
on pins DP and DM
0
-
3.6
V
on pin XTAL1
[1]
0
-
1.95
V
Tamb
ambient temperature
−40
+25
+85
°C
Tj
junction temperature
−40
-
+125
°C
[1]
VCC(I/O) must be less than or equal to VCC.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
53 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
14. Static characteristics
Table 44. Static characteristics: supply pins
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Min
Typ
Max
Unit
V(REG3V3) voltage on pin REG3V3
3.0
3.3
3.6
V
V(REG1V8) voltage on pin REG1V8
1.65
1.8
1.95
V
1.0
-
1.5
V
low-power mode; VBUS valid detector
disabled; 1.5 kΩ pull-up resistor on
pin DP disconnected
-
30
85
µA
low-power mode; VBUS valid detector
disabled; 1.5 kΩ pull-up resistor on
pin DP connected
-
215
280
µA
full-speed idle; no USB activity
-
10
-
mA
VPOR(trip)
power-on reset trip
voltage
ICC
supply current
Conditions
high-speed idle; no USB activity
ICC(I/O)
[1]
supply current on
pin VCC(I/O)
-
19
-
mA
full-speed continuous data transmit;
50 pF load on pins DP and DM
[1]
-
15
-
mA
full-speed continuous data receive
[1]
-
11
-
mA
high-speed continuous data transmit;
45 Ω load on pins DP and DM to ground
[1]
-
48
-
mA
high-speed continuous data receive
[1]
-
28
-
mA
-
-
1
µA
static current; I/O pins are idle
A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.
Table 45. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N/PSW_N)
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
-
-
0.3 × VCC(I/O) V
Input levels
VIL
LOW-level input voltage
VIH
HIGH-level input voltage
0.7 × VCC(I/O)
-
-
V
IIL
LOW-level input current
VI = 0 V
-
-
1
µA
IIH
HIGH-level input current
VI = VCC(I/O)
-
-
1
µA
ILI
input leakage current
−1
+0.1
+1
µA
Output levels
VOL
LOW-level output voltage
IOL = +2 mA
-
-
0.4
V
VOH
HIGH-level output voltage
IOH = −2 mA
VCC(I/O) − 0.4
-
-
V
IOH
HIGH-level output current
VO = VCC(I/O) − 0.4 V
−4.8
-
-
mA
IOL
LOW-level output current
VO = 0.4 V
4.2
-
-
mA
IOZ
off-state output current
0 V < VO < VCC(I/O)
-
-
1
µA
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
54 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 45. Static characteristics: digital pins (CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N/PSW_N) …continued
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
45
-
65
Ω
Impedance
load impedance
ZL
Pull-up and pull-down
Ipd
pull-down current
interface protect
enabled; DATA[7:0]
pins only; VI = VCC(I/O)
25
50
90
µA
Ipu
pull-up current
interface protect
enabled; STP pin only;
VI = 0 V
−30
−50
−80
µA
pins STP, RESET_N,
DATA[7:0]
-
-
3.5
pF
Capacitance
input capacitance
Cin
Table 46. Static characteristics: pin VBUS/FAULT
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Applicable only when pin VBUS/FAULT is used as FAULT.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Input levels
VIL
LOW-level input voltage
-
-
0.8
V
VIH
HIGH-level input voltage
2.0
-
-
V
IIL
LOW-level input current
VI = 0 V
-
-
1
µA
IIH
HIGH-level input current
VI = VCC(I/O)
-
-
1
µA
Table 47. Static characteristics: analog I/O pins (DP, DM)
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Original USB transceiver (low-speed and full-speed)
Input levels (differential receiver)
VDI
differential input sensitivity voltage |VDP − VDM|
0.2
-
-
V
VCM
differential common mode voltage
range
0.8
-
2.5
V
includes VDI range
Input levels (single-ended receivers)
VIL
LOW-level input voltage
-
-
0.8
V
VIH
HIGH-level input voltage
2.0
-
-
V
Output levels
VOL
LOW-level output voltage
pull-up on pin DP;
RL = 1.5 kΩ to 3.6 V
0.0
0.18
0.3
V
VOH
HIGH-level output voltage
pull-down on pins DP and
DM; RL = 15 kΩ to GND
2.8
3.2
3.6
V
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
55 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 47. Static characteristics: analog I/O pins (DP, DM) …continued
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
termination voltage for upstream
facing port pull-up
for 1.5 kΩ pull-up resistor
3.0
-
3.6
V
1425
1500
1575
Ω
Termination
VTERM
Resistance
RUP(DP)
pull-up resistance on pin DP
High-speed USB transceiver
Input levels (differential receiver)
VHSSQ
high-speed squelch detection
threshold voltage (differential
signal amplitude)
100
-
150
mV
VHSDSC
high-speed disconnect detection
threshold voltage (differential
signal amplitude)
525
-
625
mV
VHSDI
high-speed differential input
sensitivity
|VDP − VDM|
300
-
-
mV
VHSCM
high-speed data signaling
common mode voltage range
(guideline for receiver)
includes VDI range
−50
-
+500
mV
VHSOI
high-speed idle level voltage
−10
-
+10
mV
VHSOL
high-speed data signaling
LOW-level voltage
−10
-
+10
mV
Output levels
VHSOH
high-speed data signaling
HIGH-level voltage
360
-
440
mV
VCHIRPJ
Chirp J level (differential voltage)
700
-
1100
mV
VCHIRPK
Chirp K level (differential voltage)
−900
-
−500
mV
−1
-
+1
µA
-
-
5
pF
Leakage current
off-state leakage current
ILZ
Capacitance
input capacitance
Cin
pin to GND
Resistance
RDN(DP)
pull-down resistance on pin DP
14.25
15
15.75
kΩ
RDN(DM)
pull-down resistance on pin DM
14.25
15
15.75
kΩ
Termination
driver output impedance on pin DP steady-state drive
[1]
40.5
45
49.5
Ω
ZO(drv)(DM)
driver output impedance on
pin DM
[1]
40.5
45
49.5
Ω
ZINP
input impedance exclusive of
pull-up/pull-down (for
low-/full-speed)
10
-
-
MΩ
ZO(drv)(DP)
[1]
steady-state drive
For high-speed USB and full-speed USB.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
56 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 48. Static characteristics: VBUS comparators
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
VA_VBUS_VLD
A-device VBUS valid voltage
Conditions
Min
Typ
Max
Unit
4.4
4.5
4.65
V
VB_SESS_VLD
B-device session valid voltage
0.8
1.6
2.0
V
Vhys(B_SESS_VLD)
B-device session valid hysteresis
voltage
70
140
200
mV
VB_SESS_END
B-device session end voltage
0.2
0.5
0.8
V
for A-device and
B-device
Table 49. Static characteristics: VBUS resistors
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
RUP(VBUS)
pull-up resistance on
pin VBUS
connect to pin REG3V3 when
CHRG_VBUS is logic 1
281
680
-
Ω
RDN(VBUS)
pull-down resistance on
pin VBUS
connect to GND when
DISCHRG_VBUS is logic 1
656
850
-
Ω
RI(idle)(VBUS)
idle input resistance on
pin VBUS
40
57
80
kΩ
Table 50. Static characteristics: resistor reference
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VO(RREF)
output voltage on pin RREF
SUSPENDM is logic 1
-
1.22
-
V
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
57 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
15. Dynamic characteristics
Table 51. Dynamic characteristics: reset and clock
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
Reset
tW(POR)
internal power-on reset pulse
width
0.2
-
-
µs
tw(REG1V8_H)
REG1V8 HIGH pulse width
2
-
-
µs
tw(REG1V8_L)
REG1V8 LOW pulse width
11
-
-
µs
tW(RESET_N)
external RESET_N pulse width
200
-
-
ns
tPWRUP
regulator start-up time
4.7 µF ± 20 % capacitor each on
pins REG1V8 and REG3V3
-
-
1
ms
ISP1507CBS
-
19.2
-
MHz
ISP1507DBS
-
26
-
MHz
ISP1507CBS
-
-
200
ps
Crystal or clock applied to XTAL1
input frequency on pin XTAL1
fi(XTAL1)
tjit(i)(XTAL1)RMS
RMS input jitter on pin XTAL1
δi(XTAL1)
input duty cycle on pin XTAL1
∆fi(XTAL1)
input frequency tolerance on
pin XTAL1
tr(XTAL1)
rise time on pin XTAL1
tf(XTAL1)
V(XTAL1)(p-p)
ISP1507DBS
-
-
300
ps
-
50
-
%
-
50
200
ppm
only for square wave input
-
-
5
ns
fall time on pin XTAL1
only for square wave input
-
-
5
ns
peak-to-peak voltage on
pin XTAL1
only for square wave input
0.566
-
1.95
V
applicable only when clock is
applied on pin XTAL1
[1]
Output CLOCK characteristics
fo(CLOCK)
output frequency on pin CLOCK
-
60
-
MHz
tjit(o)(CLOCK)RMS
RMS output jitter on pin CLOCK
-
-
500
ps
δo(CLOCK)
output clock duty cycle on
pin CLOCK
45
50
55
%
tstartup(PLL)
PLL startup time
-
650
-
µs
tstartup(o)(CLOCK)
output CLOCK start-up time
450
650
900
µs
[1]
measured from power good or
assertion of pin STP
The internal PLL is triggered only on the positive edge from the crystal oscillator. Therefore, the duty cycle is not critical.
Table 52. Dynamic characteristics: digital I/O pins
VCC = 3.0 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VCC(I/O) = 1.65 V to 1.95 V
tsu(DATA)
DATA set-up time with respect to 20 pF total external load
the rising edge of pin CLOCK
per pin
5.7
-
-
ns
th(DATA)
DATA hold time with respect to
the rising edge of pin CLOCK
0
-
-
ns
20 pF total external load
per pin
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
58 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 52. Dynamic characteristics: digital I/O pins …continued
VCC = 3.0 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
td(DATA)
Conditions
Min
Typ
Max
Unit
DATA output delay with respect 20 pF total external load
to the rising edge of pin CLOCK per pin
-
-
7.8
ns
tsu(STP)
STP set-up time with respect to
the rising edge of pin CLOCK
20 pF total external load
per pin
4.5
-
-
ns
th(STP)
STP hold time with respect to
the rising edge of pin CLOCK
20 pF total external load
per pin
0
-
-
ns
td(DIR)
DIR output delay with respect to 20 pF total external load
the rising edge of pin CLOCK
per pin
-
-
8.9
ns
td(NXT)
NXT output delay with respect to 20 pF total external load
the rising edge of pin CLOCK
per pin
-
-
8.9
ns
VCC(I/O) = 3.0 V to 3.6 V
tsu(DATA)
DATA set-up time with respect to 30 pF total external load
the rising edge of pin CLOCK
per pin
3.3
-
-
ns
th(DATA)
DATA hold time with respect to
the rising edge of pin CLOCK
0.8
-
-
ns
td(DATA)
DATA output delay with respect 30 pF total external load
to the rising edge of pin CLOCK per pin
-
-
5.5
ns
tsu(STP)
STP set-up time with respect to
the rising edge of pin CLOCK
30 pF total external load
per pin
3.4
-
-
ns
th(STP)
STP hold time with respect to
the rising edge of pin CLOCK
30 pF total external load
per pin
0.8
-
-
ns
td(DIR)
DIR output delay with respect to 30 pF total external load
the rising edge of pin CLOCK
per pin
-
-
6.6
ns
td(NXT)
NXT output delay with respect to 30 pF total external load
the rising edge of pin CLOCK
per pin
-
-
6.6
ns
30 pF total external load
per pin
Table 53. Dynamic characteristics: analog I/O pins (DP, DM)
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
High-speed driver
tHSR
rise time (10 % to 90 %)
500
-
-
ps
tHSF
fall time (10 % to 90 %)
500
-
-
ps
Full-speed driver
tFR
rise time
CL = 50 pF; 10 % to 90 % of
|VOH − VOL|
4
-
20
ns
tFF
fall time
CL = 50 pF; 10 % to 90 % of
|VOH − VOL|
4
-
20
ns
tFRFM
differential rise and fall time excluding the first transition
matching
from the idle state
90
-
111.1
%
VCRS
output signal crossover
voltage
excluding the first transition
from the idle state
1.3
-
2.0
V
CL = 200 pF to 600 pF;
1.5 kΩ pull-up resistor on
pin DM enabled; 10 % to
90 % of |VOH − VOL|
75
-
300
ns
Low-speed driver
tLR
transition time: rise time
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
59 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 53. Dynamic characteristics: analog I/O pins (DP, DM) …continued
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = −40 °C to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tLF
transition time: fall time
CL = 200 pF to 600 pF;
1.5 kΩ pull-up resistor on
pin DM enabled; 10 % to
90 % of |VOH − VOL|
75
-
300
ns
tLRFM
rise and fall time matching
tLR/tLF; excluding the first
transition from the idle state
80
-
125
%
Driver timing
tPLH(drv)
driver propagation delay
(LOW to HIGH)
TX_DAT, TX_SE0 to DP, DM;
see Figure 22
-
-
11
ns
tPHL(drv)
driver propagation delay
(HIGH to LOW)
TX_DAT, TX_SE0 to DP, DM;
see Figure 22
-
-
11
ns
tPHZ
driver disable delay from
HIGH level
TX_ENABLE to DP, DM;
see Figure 23
-
-
12
ns
tPLZ
driver disable delay from
LOW level
TX_ENABLE to DP, DM;
see Figure 23
-
-
12
ns
tPZH
driver enable delay to HIGH TX_ENABLE to DP, DM;
level
see Figure 23
-
-
20
ns
tPZL
driver enable delay to LOW TX_ENABLE to DP, DM;
level
see Figure 23
-
-
20
ns
Receiver timing
Differential receiver
tPLH(rcv)
receiver propagation delay
(LOW to HIGH)
DP, DM to RX_RCV, RX_DP
and RX_DM; see Figure 24
-
-
17
ns
tPHL(rcv)
receiver propagation delay
(HIGH to LOW)
DP, DM to RX_RCV, RX_DP
and RX_DM; see Figure 24
-
-
17
ns
Single-ended receiver
tPLH(se)
single-ended propagation
delay (LOW to HIGH)
DP, DM to RX_RCV, RX_DP
and RX_DM; see Figure 24
-
-
17
ns
tPHL(se)
single-ended propagation
delay (HIGH to LOW)
DP, DM to RX_RCV, RX_DP
and RX_DM; see Figure 24
-
-
17
ns
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
60 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
1.8 V
0.9 V
logic input 0.9 V
tHSF, tFF, tLF
tHSR, tFR, tLR
0V
VOH
VOL
90 %
tPLH(drv)
90 %
tPHL(drv)
VOH
10 %
differential
data lines
10 %
VCRS
VOL
004aaa861
Fig 21. Rise time and fall time
VCRS
004aaa573
Fig 22. Timing of TX_DAT and TX_SE0 to DP and DM
2.0 V
1.8 V
logic 0.9 V
input
differential
data lines
0.9 V
VCRS
VCRS
0.8 V
0V
VOH
tPLH(rcv)
tPLH(se)
tPHZ
tPLZ
tPZH
tPZL
VOH
VOH − 0.3 V
differential
data lines
VOL + 0.3 V
VOL
004aaa574
Fig 23. Timing of TX_ENABLE to DP and DM
0.9 V
0.9 V
logic output
VCRS
VOL
tPHL(rcv)
tPHL(se)
004aaa575
Fig 24. Timing of DP and DM to RX_RCV, RX_DP and
RX_DM
15.1 ULPI timing
ULPI timing requirements are given in Figure 25. This timing applies to synchronous
mode only. All timing is measured with respect to the ISP1507 CLOCK pin. All signals are
clocked on the rising edge of CLOCK.
CLOCK
tsu(STP) th(STP)
CONTROL IN
(STP)
tsu(DATA) th(DATA)
DATA IN
(8-BIT)
td(DIR),
td(NXT)
CONTROL OUT
(DIR, NXT)
td(DATA)
td(DIR),
td(NXT)
DATA OUT
(8-BIT)
004aaa722
Fig 25. ULPI timing
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
61 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
16. Application information
Table 54.
Recommended bill of materials
Designator[1]
Application
Value
Comment
Cbypass
highly recommended for all
applications
0.1 µF
-
Cfilter
highly recommended for all
applications
4.7 µF ± 20 %; use a LOW
ESR capacitor (0.2 Ω to
2 Ω) for best performance
-
CVBUS
mandatory for peripherals
0.1 µF and 1 µF to 10 µF in parallel
mandatory for host
0.1 µF and 120 µF ± 20 %
(min) in parallel
-
mandatory for OTG
0.1 µF and 1 µF to 6.5 µF
in parallel
-
DESD
recommended for all
ESD-sensitive applications
-
IP4359CX4/LF; Wafer-Level Chip-Scale
Package (WLCSP); ESD IEC 61000-4-2
level 4; ±15 kV contact; ±15 kV air discharge
compliant protection
Rpullup
recommended; for applications 4.7 kΩ (recommended)
with an external VBUS supply
controlled by PSW_N
maximum value is determined by the voltage
drop on PSW_N caused by leakage into
PSW_N and the external supply control pin
RRREF
mandatory in all applications
12 kΩ ± 1 %
-
RVBUS
strongly recommended for
peripheral or external 5 V
applications only
1 kΩ ± 5 %
-
RXTAL
required only for applications
driving a square wave into the
XTAL1 pin
47 kΩ ± 5 %
used to avoid floating input on the XTAL1 pin
XTAL
crystal is used
19.2 MHz
CL = 10 pF; RS < 220 Ω; CXTAL = 18 pF
26 MHz
CL = 10 pF; RS < 130 Ω; CXTAL = 18 pF
-
CSTCE26M0XK2***-R0[2]
CXTAL is not required
C(XTAL)SQ
required only for applications
100 pF
driving a square wave into the
XTAL1 pin that has a DC offset
used to AC couple the input square wave to
the XTAL1 pin
[1]
For detailed information and alternative interface options, refer to the Interfacing to the ISP1507 (AN10080) application note.
[2]
For more information, contact Murata.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
62 of 74
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
VCC(I/O)
Cbypass
+5 V
IN
Rpullup
ON
NXP Semiconductors
ISP1507C_ISP1507D_1
Product data sheet
VCC
Cbypass
FAULT
VBUS
SWITCH
Cbypass
DATA1
OUT
1
24
2
23
DATA2
DATA0
DATA0
VCC(I/O)
DATA1
VCC(I/O)
3
22
DATA3
DATA2
1
RRREF
VBUS
RREF
4
21
CLOCK
DATA3
3
USB
STANDARD-A
RECEPTACLE
4
5
D+
DP
GND
SHIELD
SHIELD
VCC
VBUS/FAULT
CVBUS
A1
A2
REG3V3
IP4359CX4/LF
7
SHIELD
B1
B2
XTAL1
DESD
8
SHIELD
5
20
6
19
XTAL(1)
63 of 74
© NXP B.V. 2008. All rights reserved.
Cbypass
Cfilter
CXTAL
DATA4
DATA5
DATA5
HOST
CONTROLLER
ISP1507
7
18
8
17
9
16
10
15
11
14
12
13
XTAL2
RESET_N/
PSW_N
DATA4
DATA6
DATA6
DATA7
DATA7
NXT
NXT
STP
STP
DIR
DIR
REG1V8
CLOCK
GND (die pad)
CXTAL
Cbypass
Cfilter
004aab081
(1) Frequency is version dependent: ISP1507CBS: 19.2 MHz; ISP1507DBS: 26 MHz.
Fig 26. Using the ISP1507 with a USB host controller; external 5 V source with built-in FAULT and external crystal
ISP1507C; ISP1507D
6
DM
ULPI HS USB host and peripheral transceiver
Rev. 01 — 28 May 2008
2
D−
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
NXP Semiconductors
ISP1507C_ISP1507D_1
Product data sheet
VCC(I/O)
Cbypass
Cbypass
VCC
DATA0
Cbypass
DATA1
DATA0
VCC(I/O)
1
2
USB
STANDARD-B
RECEPTACLE
4
RVBUS
RREF
DM
D+
DP
VCC
GND
A1
SHIELD
A2
VBUS/FAULT
IP4359CX4/LF
SHIELD
B1
B2
REG3V3
DESD
SHIELD
SHIELD
8
23 VCC(I/O)
3
22 DATA3
DATA2
DATA3
4
XTAL1
CVBUS
Cbypass
Cfilter
XTAL2
RESET_N/
PSW_N
5
CLOCK
20 DATA4
6
DATA4
19 DATA5
DATA5
PERIPHERAL
CONTROLLER
ISP1507
7
18 DATA6
DATA6
8
17 DATA7
DATA7
9
16 NXT
NXT
10
15 STP
STP
11
14 DIR
DIR
12
13 REG1V8
GND (die pad)
Cbypass
64 of 74
© NXP B.V. 2008. All rights reserved.
C(XTAL)SQ
fi(XTAL1)(1)
Cfilter
RXTAL
(1) Frequency is version dependent: ISP1507CBS: 19.2 MHz; ISP1507DBS: 26 MHz.
Fig 27. Using the ISP1507 with a peripheral controller; external square wave input on pin XTAL1
004aab082
ISP1507C; ISP1507D
6
7
2
DATA1
21 CLOCK
D_
5
24 DATA2
ULPI HS USB host and peripheral transceiver
Rev. 01 — 28 May 2008
3
VBUS
RRREF
1
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
17. Package outline
HVQFN24: plastic thermal enhanced very thin quad flat package; no leads;
24 terminals; body 4 x 4 x 0.85 mm
A
B
D
SOT616-3
terminal 1
index area
A
A1
E
c
detail X
e1
C
1/2 e
e
12
y
y1 C
v M C A B
w M C
b
7
L
13
6
e
e2
Eh
1/2 e
1
18
terminal 1
index area
24
19
X
Dh
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A(1)
max.
A1
b
c
D (1)
Dh
E (1)
Eh
e
e1
e2
L
v
w
y
y1
mm
1
0.05
0.00
0.30
0.18
0.2
4.1
3.9
2.75
2.45
4.1
3.9
2.75
2.45
0.5
2.5
2.5
0.5
0.3
0.1
0.05
0.05
0.1
Note
1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
JEITA
SOT616-3
---
MO-220
---
EUROPEAN
PROJECTION
ISSUE DATE
04-11-19
05-03-10
Fig 28. Package outline SOT616-3 (HVQFN24)
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
65 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
18. Soldering of SMD packages
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description”.
18.1 Introduction to soldering
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
18.2 Wave and reflow soldering
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
• Through-hole components
• Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
•
•
•
•
•
•
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus SnPb soldering
18.3 Wave soldering
Key characteristics in wave soldering are:
• Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
• Solder bath specifications, including temperature and impurities
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
66 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
18.4 Reflow soldering
Key characteristics in reflow soldering are:
• Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see Figure 29) than a SnPb process, thus
reducing the process window
• Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
• Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 55 and 56
Table 55.
SnPb eutectic process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
≥ 350
< 2.5
235
220
≥ 2.5
220
220
Table 56.
Lead-free process (from J-STD-020C)
Package thickness (mm)
Package reflow temperature (°C)
Volume (mm3)
< 350
350 to 2000
> 2000
< 1.6
260
260
260
1.6 to 2.5
260
250
245
> 2.5
250
245
245
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see Figure 29.
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
67 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
maximum peak temperature
= MSL limit, damage level
temperature
minimum peak temperature
= minimum soldering temperature
peak
temperature
time
001aac844
MSL: Moisture Sensitivity Level
Fig 29. Temperature profiles for large and small components
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”.
19. Abbreviations
Table 57.
Abbreviations
Acronym
Description
ASIC
Application-Specific Integrated Circuit
ATX
Analog USB Transceiver
CD-RW
Compact Disc-ReWritable
EOP
End-Of-Packet
ESD
ElectroStatic Discharge
ESR
Effective Series Resistance
FS
Full-Speed
HBM
Human Body Model
HNP
Host Negotiation Protocol
HS
High-Speed
ID
Identification
IEC
International Electrotechnical Commission
LS
Low-Speed
MO
Magneto-Optical
NRZI
Non-Return-to-Zero Inverted
OTG
On-The-Go
PCB
Printed-Circuit Board
PDA
Personal Digital Assistant
PHY
Physical Layer
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
68 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
Table 57.
Abbreviations …continued
Acronym
Description
PID
Packet Identifier
PLD
Programmable Logic Device
PLL
Phase-Locked Loop
POR
Power-On Reset
RoHS
Restriction of Hazardous Substances
RXCMD
Receive Command
SE0
Single-Ended Zero
SOF
Start-Of-Frame
SRP
Session Request Protocol
STB
Set-Top Box
SYNC
Synchronous
TTL
Transistor-Transistor Logic
TXCMD
Transmit Command
USB
Universal Serial Bus
USB-IF
USB Implementers Forum
ULPI
UTMI+ Low Pin Interface
UTMI
USB 2.0 Transceiver Macrocell Interface
UTMI+
USB 2.0 Transceiver Macrocell Interface Plus
20. References
[1]
Universal Serial Bus Specification Rev. 2.0
[2]
On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3
[3]
UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1
[4]
UTMI+ Specification Rev. 1.0
[5]
USB 2.0 Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05
[6]
Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM)
(JESD22-A114D)
[7]
Interfacing to the ISP1507 (AN10080)
21. Revision history
Table 58.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
ISP1507C_ISP1507D_1
20080528
Product data sheet
-
-
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
69 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
22. Legal information
22.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
22.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
22.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of an NXP Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. NXP Semiconductors accepts no liability for inclusion and/or use of
NXP Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
22.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
23. Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
70 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
24. Tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Ordering information . . . . . . . . . . . . . . . . . . . . .3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5
ULPI signal description . . . . . . . . . . . . . . . . . .13
Signal mapping during low-power mode . . . . .14
Signal mapping for 6-pin serial mode . . . . . . .15
Signal mapping for 3-pin serial mode . . . . . . .16
Operating states and their corresponding
resistor settings . . . . . . . . . . . . . . . . . . . . . . . .16
TXCMD byte format . . . . . . . . . . . . . . . . . . . . .22
RXCMD byte format . . . . . . . . . . . . . . . . . . . . .23
LINESTATE[1:0] encoding for upstream
facing ports: peripherals . . . . . . . . . . . . . . . . .24
LINESTATE[1:0] encoding for downstream
facing ports: host . . . . . . . . . . . . . . . . . . . . . . .24
Encoded VBUS voltage state . . . . . . . . . . . . . .24
VBUS indicators in RXCMD required for
typical applications . . . . . . . . . . . . . . . . . . . . . .25
Encoded USB event signals . . . . . . . . . . . . . .26
PHY pipeline delays . . . . . . . . . . . . . . . . . . . . .30
Link decision times . . . . . . . . . . . . . . . . . . . . .31
Immediate register set overview . . . . . . . . . . .43
Extended register set overview . . . . . . . . . . . .43
VENDOR_ID_LOW - Vendor ID Low
register (address R = 00h) bit description . . . .44
VENDOR_ID_HIGH - Vendor ID High
register (address R = 01h) bit description . . . .44
PRODUCT_ID_LOW - Product ID Low
register (address R = 02h) bit description . . . .44
PRODUCT_ID_HIGH - Product ID High
register (address R = 03h) bit description . . . .44
FUNC_CTRL - Function Control register
(address R = 04h to 06h, W = 04h, S = 05h,
C = 06h) bit allocation . . . . . . . . . . . . . . . . . . .44
FUNC_CTRL - Function Control register
(address R = 04h to 06h, W = 04h, S = 05h,
C = 06h) bit description . . . . . . . . . . . . . . . . . .45
INTF_CTRL - Interface Control register
(address R = 07h to 09h, W = 07h, S = 08h,
C = 09h) bit allocation . . . . . . . . . . . . . . . . . . .46
INTF_CTRL - Interface Control register
(address R = 07h to 09h, W = 07h, S = 08h,
C = 09h) bit description . . . . . . . . . . . . . . . . . .46
OTG_CTRL - OTG Control register
(address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh,
C = 0Ch) bit allocation . . . . . . . . . . . . . . . . . . .47
OTG_CTRL - OTG Control register
(address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh,
C = 0Ch) bit description . . . . . . . . . . . . . . . . . .47
USB_INTR_EN_R_E - USB Interrupt Enable
Rising Edge register (address R = 0Dh to 0Fh,
W = 0Dh, S = 0Eh, C = 0Fh) bit allocation . . . .48
USB_INTR_EN_R_E - USB Interrupt Enable
Rising Edge register (address R = 0Dh to 0Fh,
W = 0Dh, S = 0Eh, C = 0Fh) bit description . .48
USB_INTR_EN_F_E - USB Interrupt Enable
Falling Edge register (address R = 10h to 12h,
W = 10h, S = 11h, C = 12h) bit allocation . . . . 48
Table 32. USB_INTR_EN_F_E - USB Interrupt Enable
Falling Edge register (address R = 10h to 12h,
W = 10h, S = 11h, C = 12h) bit description . . . 48
Table 33. USB_INTR_STAT - USB Interrupt Status
register (address R = 13h) bit allocation . . . . . 49
Table 34. USB_INTR_STAT - USB Interrupt Status
register (address R = 13h) bit description . . . . 49
Table 35. USB_INTR_L - USB Interrupt Latch register
(address R = 14h) bit allocation . . . . . . . . . . . 49
Table 36. USB_INTR_L - USB Interrupt Latch register
(address R = 14h) bit description . . . . . . . . . . 49
Table 37. DEBUG - Debug register (address R = 15h)
bit allocation . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 38. DEBUG - Debug register (address R = 15h)
bit description . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 39. SCRATCH - Scratch register (address R =
16h to 18h, W = 16h, S = 17h, C = 18h)
bit description . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 40. PWR_CTRL - Power Control register
(address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh,
C = 3Fh) bit allocation . . . . . . . . . . . . . . . . . . . 50
Table 41. PWR_CTRL - Power Control register
(address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh,
C = 3Fh) bit description . . . . . . . . . . . . . . . . . . 51
Table 42. Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 43. Recommended operating conditions . . . . . . . . 53
Table 44. Static characteristics: supply pins . . . . . . . . . . 54
Table 45. Static characteristics: digital pins
(CLOCK, DIR, STP, NXT, DATA[7:0],
RESET_N/PSW_N) . . . . . . . . . . . . . . . . . . . . . 54
Table 46. Static characteristics: pin VBUS/FAULT . . . . . . 55
Table 47. Static characteristics: analog I/O pins
(DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Table 48. Static characteristics: VBUS comparators . . . . 57
Table 49. Static characteristics: VBUS resistors . . . . . . . . 57
Table 50. Static characteristics: resistor reference . . . . . 57
Table 51. Dynamic characteristics: reset and clock . . . . 58
Table 52. Dynamic characteristics: digital I/O pins . . . . . 58
Table 53. Dynamic characteristics: analog I/O pins
(DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 54. Recommended bill of materials . . . . . . . . . . . . 62
Table 55. SnPb eutectic process (from J-STD-020C) . . . 67
Table 56. Lead-free process (from J-STD-020C) . . . . . . 67
Table 57. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Table 58. Revision history . . . . . . . . . . . . . . . . . . . . . . . . 69
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
71 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
25. Figures
Fig 1.
Fig 2.
Fig 3.
Fig 4.
Fig 5.
Fig 6.
Fig 7.
Fig 8.
Fig 9.
Fig 10.
Fig 11.
Fig 12.
Fig 13.
Fig 14.
Fig 15.
Fig 16.
Fig 17.
Fig 18.
Fig 19.
Fig 20.
Fig 21.
Fig 22.
Fig 23.
Fig 24.
Fig 25.
Fig 26.
Fig 27.
Fig 28.
Fig 29.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Pin configuration HVQFN24; top view . . . . . . . . . .5
Internal power-on reset timing . . . . . . . . . . . . . . .18
Power-up and reset sequence required
before the ULPI bus is ready for use . . . . . . . . . .20
Interface behavior with respect to RESET_N. . . .21
Single and back-to-back RXCMDs from the
ISP1507 to the link. . . . . . . . . . . . . . . . . . . . . . . .23
RXCMD A_VBUS_VLD indicator source . . . . . . .25
Example of register write, register read,
extended register write and extended
register read. . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
USB reset and high-speed detection
handshake (chirp) sequence . . . . . . . . . . . . . . . .29
Example of using the ISP1507 to transmit and
receive USB data . . . . . . . . . . . . . . . . . . . . . . . . .30
High-speed transmit-to-transmit packet timing. . .31
High-speed receive-to-transmit packet timing . . .32
Preamble sequence . . . . . . . . . . . . . . . . . . . . . . .33
Full-speed suspend and resume . . . . . . . . . . . . .34
High-speed suspend and resume . . . . . . . . . . . .36
Remote wake-up from low-power mode . . . . . . .38
Transmitting USB packets without the
automatic SYNC and EOP generation. . . . . . . . .39
Example of transmit followed by receive in
6-pin serial mode . . . . . . . . . . . . . . . . . . . . . . . . .41
Example of transmit followed by receive in
3-pin serial mode . . . . . . . . . . . . . . . . . . . . . . . . .41
Human body ESD test model. . . . . . . . . . . . . . . .52
Rise time and fall time . . . . . . . . . . . . . . . . . . . . .61
Timing of TX_DAT and TX_SE0 to DP and DM . .61
Timing of TX_ENABLE to DP and DM. . . . . . . . .61
Timing of DP and DM to RX_RCV, RX_DP
and RX_DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
ULPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Using the ISP1507 with a USB host controller;
external 5 V source with built-in FAULT and
external crystal. . . . . . . . . . . . . . . . . . . . . . . . . . .63
Using the ISP1507 with a peripheral controller;
external square wave input on pin XTAL1 . . . . . .64
Package outline SOT616-3 (HVQFN24) . . . . . . .65
Temperature profiles for large and small
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
72 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
26. Contents
1
General description . . . . . . . . . . . . . . . . . . . . . . 1
2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
4
Ordering information . . . . . . . . . . . . . . . . . . . . . 3
5
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6
Pinning information . . . . . . . . . . . . . . . . . . . . . . 5
6.1
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5
7
Functional description . . . . . . . . . . . . . . . . . . . 7
7.1
ULPI controller . . . . . . . . . . . . . . . . . . . . . . . . . 7
7.2
USB serializer and deserializer. . . . . . . . . . . . . 7
7.3
Hi-Speed USB (USB 2.0) ATX . . . . . . . . . . . . . 7
7.4
Voltage regulator. . . . . . . . . . . . . . . . . . . . . . . . 8
7.5
Crystal oscillator and PLL. . . . . . . . . . . . . . . . . 8
7.6
VBUS comparators. . . . . . . . . . . . . . . . . . . . . . . 8
7.6.1
VBUS valid comparator . . . . . . . . . . . . . . . . . . . 8
7.6.2
Session valid comparator . . . . . . . . . . . . . . . . . 9
7.6.3
Session end comparator. . . . . . . . . . . . . . . . . . 9
7.7
SRP charge and discharge resistors . . . . . . . . 9
7.8
Band gap reference voltage . . . . . . . . . . . . . . . 9
7.9
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.10
Detailed description of pins . . . . . . . . . . . . . . . 9
7.10.1
DATA[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7.10.2
VCC(I/O) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.3
RREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.4
DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.5
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.6
VBUS/FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.6.1 VBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7.10.6.2 FAULT (external overcurrent or fault detector) 10
7.10.7
REG3V3 and REG1V8 . . . . . . . . . . . . . . . . . . 11
7.10.8
XTAL1 and XTAL2. . . . . . . . . . . . . . . . . . . . . . 11
7.10.9
RESET_N/PSW_N . . . . . . . . . . . . . . . . . . . . . 11
7.10.9.1 RESET_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.10.9.2 PSW_N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7.10.10 DIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.10.11 STP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.10.12 NXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.10.13 CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7.10.14 GND (die pad). . . . . . . . . . . . . . . . . . . . . . . . . 12
8
Modes of operation . . . . . . . . . . . . . . . . . . . . . 13
8.1
ULPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8.1.1
Synchronous mode. . . . . . . . . . . . . . . . . . . . . 13
8.1.2
Low-power mode . . . . . . . . . . . . . . . . . . . . . . 14
8.1.3
6-pin full-speed or low-speed serial mode . . . 15
8.1.4
3-pin full-speed or low-speed serial mode . . . 15
8.2
USB and OTG state transitions . . . . . . . . . . .
9
Protocol description . . . . . . . . . . . . . . . . . . . .
9.1
ULPI references . . . . . . . . . . . . . . . . . . . . . . .
9.2
Power-On Reset (POR) . . . . . . . . . . . . . . . . .
9.3
Power-up, reset and bus idle sequence . . . . .
9.3.1
Interface protection. . . . . . . . . . . . . . . . . . . . .
9.3.2
Interface behavior with respect to RESET_N.
9.4
VBUS power and fault detection . . . . . . . . . . .
9.4.1
Driving 5 V on VBUS . . . . . . . . . . . . . . . . . . . .
9.4.2
Fault detection . . . . . . . . . . . . . . . . . . . . . . . .
9.5
TXCMD and RXCMD . . . . . . . . . . . . . . . . . . .
9.5.1
TXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.2
RXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.2.1
Linestate encoding . . . . . . . . . . . . . . . . . . . . .
9.5.2.2
VBUS state encoding . . . . . . . . . . . . . . . . . . . .
9.5.2.3
Using and selecting the VBUS state encoding.
9.5.2.4
RxEvent encoding . . . . . . . . . . . . . . . . . . . . .
9.6
Register read and write operations . . . . . . . .
9.7
USB reset and high-speed detection
handshake (chirp) . . . . . . . . . . . . . . . . . . . . .
9.8
USB packet transmit and receive . . . . . . . . . .
9.8.1
USB packet timing . . . . . . . . . . . . . . . . . . . . .
9.8.1.1
ISP1507 pipeline delays. . . . . . . . . . . . . . . . .
9.8.1.2
Allowed link decision time . . . . . . . . . . . . . . .
9.9
Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10
USB suspend and resume . . . . . . . . . . . . . . .
9.10.1
Full-speed and low-speed host-initiated
suspend and resume . . . . . . . . . . . . . . . . . . .
9.10.2
High-speed suspend and resume . . . . . . . . .
9.10.3
Remote wake-up . . . . . . . . . . . . . . . . . . . . . .
9.11
No automatic SYNC and EOP generation
(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.12
On-The-Go operations . . . . . . . . . . . . . . . . . .
9.12.1
OTG comparators. . . . . . . . . . . . . . . . . . . . . .
9.12.2
Pull-up and pull-down resistors . . . . . . . . . . .
9.12.3
VBUS charge and discharge resistors . . . . . . .
9.13
Serial modes . . . . . . . . . . . . . . . . . . . . . . . . .
9.14
Aborting transfers. . . . . . . . . . . . . . . . . . . . . .
9.15
Avoiding contention on the ULPI data bus . . .
10
Register map . . . . . . . . . . . . . . . . . . . . . . . . . .
10.1
Immediate register set . . . . . . . . . . . . . . . . . .
10.1.1
Vendor ID and Product ID registers . . . . . . . .
10.1.1.1 VENDOR_ID_LOW register . . . . . . . . . . . . . .
10.1.1.2 VENDOR_ID_HIGH register . . . . . . . . . . . . .
10.1.1.3 PRODUCT_ID_LOW register. . . . . . . . . . . . .
10.1.1.4 PRODUCT_ID_HIGH register . . . . . . . . . . . .
10.1.2
FUNC_CTRL register. . . . . . . . . . . . . . . . . . .
16
18
18
18
18
20
21
21
21
21
22
22
22
23
24
25
26
27
27
30
30
30
30
32
33
33
34
37
38
39
40
40
40
40
42
42
43
44
44
44
44
44
44
44
continued >>
ISP1507C_ISP1507D_1
Product data sheet
© NXP B.V. 2008. All rights reserved.
Rev. 01 — 28 May 2008
73 of 74
ISP1507C; ISP1507D
NXP Semiconductors
ULPI HS USB host and peripheral transceiver
10.1.3
10.1.4
10.1.5
10.1.6
10.1.7
10.1.8
10.1.9
10.1.10
10.1.11
10.1.12
10.1.13
10.1.14
10.2
11
11.1
11.2
12
13
14
15
15.1
16
17
18
18.1
18.2
18.3
18.4
19
20
21
22
22.1
22.2
22.3
22.4
23
24
25
26
INTF_CTRL register . . . . . . . . . . . . . . . . . . . .
OTG_CTRL register . . . . . . . . . . . . . . . . . . . .
USB_INTR_EN_R_E register . . . . . . . . . . . . .
USB_INTR_EN_F_E register . . . . . . . . . . . . .
USB_INTR_STAT register. . . . . . . . . . . . . . . .
USB_INTR_L register . . . . . . . . . . . . . . . . . . .
DEBUG register . . . . . . . . . . . . . . . . . . . . . . .
SCRATCH register . . . . . . . . . . . . . . . . . . . . .
Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access extended register set . . . . . . . . . . . . .
Vendor-specific registers . . . . . . . . . . . . . . . .
PWR_CTRL register . . . . . . . . . . . . . . . . . . . .
Extended register set . . . . . . . . . . . . . . . . . . .
ElectroStatic Discharge (ESD) . . . . . . . . . . . .
ESD protection . . . . . . . . . . . . . . . . . . . . . . . .
ESD test conditions . . . . . . . . . . . . . . . . . . . .
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . .
Recommended operating conditions. . . . . . .
Static characteristics. . . . . . . . . . . . . . . . . . . .
Dynamic characteristics . . . . . . . . . . . . . . . . .
ULPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application information. . . . . . . . . . . . . . . . . .
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
Soldering of SMD packages . . . . . . . . . . . . . .
Introduction to soldering . . . . . . . . . . . . . . . . .
Wave and reflow soldering . . . . . . . . . . . . . . .
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . .
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .
References . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . . .
Legal information. . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information. . . . . . . . . . . . . . . . . . . . .
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
47
47
48
49
49
50
50
50
50
50
50
51
52
52
52
53
53
54
58
61
62
65
66
66
66
66
67
68
69
69
70
70
70
70
70
70
71
72
73
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2008.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 28 May 2008
Document identifier: ISP1507C_ISP1507D_1