INCH-POUND The documentation and process conversion measures necessary to comply with this revision shall be completed by 15 May 2002. MIL-PRF-19500/376F 15 February 2002 SUPERSEDING MIL-PRF-19500/376E 31 August 2000 PERFORMANCE SPECIFICATION SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWER TYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKC This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the performance requirements for NPN, silicon, low-power transistors. Four levels of product assurance are provided for each device type as specified in MIL-PRF-19500. Two levels of product assurance are provided for die. 1.2 Physical dimensions. See figure 1 (similar to T0-18), figures 2 and 3 (surface mount case outlines UA and UB), and figures 4 and 5 (die). 1.3 Maximum ratings. Types PT (1) VCBO VEBO VCEO IC TJ and TSTG RθJA mW V dc V dc V dc mA dc °C °C/W 360 360 360 60 60 60 6 6 6 60 60 60 50 50 50 -65 to +200 -65 to +200 -65 to +200 325 325 325 TA = +25°C 2N2484 2N2484UA 2N2484UB (1) Derate linearly at 2.06 mW/°C above TA = +25°C. 1.4 Primary electrical characteristics. Limits hfe Cobo |hfe|2 VCE(sat) (1) VCE = 5 V dc IC = 1 mA dc f = 1 kHz IE = 0 VCB = 5 V dc 100 kHz ≤ f ≤ 1 MHz IC = 500 µA dc VCE = 5 V dc f = 30 MHz IC = 1.0 mA dc IB = 0.1 mA dc pF Min Max 250 900 5.0 V dc 2.0 7.0 0.3 (1) Pulsed (see 4.5.1). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAC, P.O. Box 3990, Columbus, OH 43216-5000), by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5961 MIL-PRF-19500/376F Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r α Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.7 19.05 0 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .040 0.86 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .010 0.25 45° TP 45° TP Note 6 7,8 7,8 7,8 7,8 7,8 5 3,4 3 10 6 NOTES: 1. Dimension are in inches. 2. Metric equivalents are given for general information only. 3. Beyond r (radius) maximum, TW shall be held for a minimum length of .011 inch (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ANSI Y14.5M, diameters are equivalent to φx symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector. FIGURE 1. Physical dimensions (similar to TO-18). 2 MIL-PRF-19500/376F Symbol A A1 B1 B2 B3 D D1 D2 D3 E E3 L1 L2 L3 Dimensions Inches Millimeters Min Max Min Max .061 .075 1.55 1.90 .029 .041 0.74 1.04 .022 .028 0.56 0.71 .075 REF 1.91 REF .006 .022 0.15 0.56 .145 .155 3.68 3.93 .045 .055 1.14 1.39 .0375 BSC .952 BSC .155 3.93 .215 .225 5.46 5.71 .225 5.71 .032 .048 0.81 1.22 .072 .088 1.83 2.23 .003 .007 0.08 0.18 Note 3 5 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Dimension "A" controls the overall package thickness. When a window lid is used, dimension "A" must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4. The corner shape (square, notch, radius, etc.) may vary at the manufacturer's option, from that shown on the drawing. 5. Dimensions "B3" minimum and "L3" minimum and the appropriately castellation length define an unobstructed three-dimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on bottom two layers, optional on top ceramic layer.) Dimension "B3" maximum and "L3" maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping. 6. Lead 4 = no connection. FIGURE 2. Physical dimensions, surface mount (2N2484UA). 3 MIL-PRF-19500/376F Ltr A A1 B1 B2 B3 D D1 D2 D3 E E3 L1 L2 Dimensions Inches Millimeters Min. Max. Min. Max. .046 .056 0.97 1.42 .017 .035 0.43 0.89 .016 .024 0.41 0.61 .016 .024 0.41 0.61 .016 .024 0.41 0.61 .085 .108 2.41 2.74 .071 .079 1.81 2.01 .035 .039 0.89 0.99 .085 .108 2.41 2.74 .115 .128 2.82 3.25 .128 3.25 .022 .038 0.56 0.96 .022 .038 0.56 0.96 Notes 3 3 3 4 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Dimensions B2 and B3 are identical to B1 4. Dimension L2 is identical to L1. FIGURE 3. Physical dimensions, surface mount (2N2484UB). 4 MIL-PRF-19500/376F A- version NOTES: 1. Die size: 2. Die thickness: 3. Top metal: 4. Back metal: 5. 6. 7. 8. .015 (0.381 mm) x .019 inch (0.421 mm) ± .001 inch (0.025 mm). .010 (0.254 mm) ± .0015 inch (0.038 mm). Aluminum 15,000 Å minimum, 18,000 Å nominal. A. Gold 2,500 Å minimum, 3,000 Å nominal. B. Eutectic Mount – No Gold. Backside: Collector. Bonding pad: B = .003 inch (0.076 mm), E = .004 inch (0.102 mm)diameter. Passivation: Si3N4 (Silicon Nitride) 2,000 Å min, 2200 Å nom. Metric equivalents are given for general information only. FIGURE 4. Physical dimensions, JANHC and JANKC die, A - version. 5 MIL-PRF-19500/376F B - version NOTES: 1. 2. 3. 4. 5. 6. 7. 8. 9. Die size: .018 (0.056 mm) x .018 inch (0.056 mm). Die thickness: .008 (0.203 mm) ± .0016 inch (0.401 mm). Base pad: .0025 inch (0.064 mm) diameter. Emitter pad: .003 inch (0.076 mm) diameter. Back metal: Gold, 6,500 ± 1950 Å. Top metal: Aluminum, 19,500 ± 2500 Å. Back side: Collector. Glassivation: SiO2, 7,500 ± 1,500 Å. Metric equivalents are given for general information only. FIGURE 5. Physical dimensions, JANHC and JANKC die, B - version. 6 MIL-PRF-19500/376F 1.4 Primary electrical characteristics. NF IC = 10 µA dc, VCE = 5 V dc Rg = 10 kΩ f = 100 Hz f = 1000 Hz f = 10 kHz Min Max dB dB dB 7.5 3 2 hFE2 hFE5 VCE = 5 V dc IC = 10 µA dc VCE = 5 V dc IC = 1 mA dc 200 500 250 800 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-19500 - Semiconductor Devices, General Specification for. STANDARD DEPARTMENT OF DEFENSE MIL-STD-750 - Test Methods for Semiconductor Devices. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Document Automation and Production Services (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 7 MIL-PRF-19500/376F 3. REQUIREMENTS 3.1 General. The requirements for acquiring the product described herein shall consist of this document and MIL-PRF-19500. 3.2 Qualification. Devices furnished under this specification shall be products that are manufactured by a manufacturer authorized by the qualifying activity for listing on the applicable qualified manufacturer’s list (QML) before contract award (see 4.2 and 6.3). 3.3 Abbreviations, symbols, and definitions. Abbreviations, symbols, and definitions used herein shall be as specified in MIL-PRF-19500. 3.4 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-19500 and figures 1, 2, 3, 4, and 5 herein. 3.4.1 Lead finish. Unless otherwise specified, lead finish shall be solderable in accordance with MIL-PRF-19500, and herein. 3.5 Marking. Marking shall be in accordance with MIL-PRF-19500, except for the UB suffix package. Marking on the UB package shall consist of an abbreviated part number, the date code, and the manufacturers symbol or logo. The prefixes JAN, JANTX, JANTXV, and JANS can be abbreviated as J, JX, JV, and JS respectively. The "2N" prefix can also be omitted. 3.6 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in 1.3, 1.4, and table I. 3.7 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I herein. 3.8 Workmanship. Semiconductor devices shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. Qualification inspection (see 4.2). b. Screening (see 4.3). c. Conformance inspection (see 4.4 and tables I, II, and III). 4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-19500 and as specified herein. 4.2.1. JANHC and JANKC qualification. JANHC and JANKC qualification inspection shall be in accordance with MIL-PRF-19500. * 4.2.4 Group E qualification. Group E inspection shall be performed for qualification or re-qualification only. In case qualification was awarded to a prior revision of the associated specification that did not request the performance of table II tests, the tests specified in table II herein must be performed by the first inspection lot of this revision to maintain qualification. 8 MIL-PRF-19500/376F * 4.3 Screening (JANS, JANTX, and JANTXV levels only). Screening shall be in accordance with table IV of MIL-PRF-19500, and as specified herein. The following measurements shall be made in accordance with table I herein. Devices that exceed the limits of table I herein shall not be acceptable. Measurement Screen (see table IV of MIL-PRF-19500) JANS level JANTX and JANTXV levels 3c Thermal impedance, method 3131 of MIL-STD-750. Thermal impedance, method 3131 of MIL-STD-750. 9 ICBO2, hFE4 Not applicable 10 48 hours minimum 48 hours minimum 11 ICBO2; hFE4; ∆ICBO2 = 100 percent of initial value or 2 nA dc, whichever is greater. ∆hFE4 = ±15 percent See 4.3.2 240 hours minimum Subgroups 2 and 3 of table I herein; ∆ICBO2 = 100 percent of initial value or 2 nA dc, whichever is greater; ∆hFE4 = ±15 percent ICBO2 ,hFE4 12 13 See 4.3.2 80 hours minimum Subgroup 2 of table I herein; ∆ICBO2 = 100 percent of initial value or 2 nA dc, whichever is greater; ∆hFE4 = ±25 percent * 4.3.1 Screening (JANHC and JANKC). Screening for JANHC and JANKC die shall be in accordance with MIL-PRF-19500 "Discrete Semiconductor Die/Chip Lot Acceptance". Burn-in duration for the JANKC level follows JANS requirements; the JANHC follows JANTX requirements. * 4.3.2 Power burn-in conditions. Power burn-in conditions are as follows: VCB = 10 to 30 V dc, PD = 360 mW, no heat sink or forced air cooling on the devices shall be permitted. 4.4 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-19500, and as specified herein. If alternate screening is being performed in accordance with MIL-PRF-19500, a sample of screened devices shall be submitted to and pass the requirements of group A1 and A2 inspection only (table VIb, group B, subgroup 1 is not required to be performed again if group B has already been satisfied in accordance with 4.4.2). 4.4.1 Group A inspection. Group A inspection shall be conducted in accordance with MIL-PRF-19500 and table I herein. 4.4.2 Group B inspection. Group B inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VIa (JANS) of MIL-PRF-19500 and 4.4.2.1. Electrical measurements (end-points) shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be in accordance with table III herein. See 4.4.2.2 for JAN, JANTX, and JANTXV group B testing. Electrical measurements (end-points) and delta requirements for JAN, JANTX, and JANTXV shall be after each step in 4.4.2.2 and shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be after each step and shall be in accordance with table III herein. 9 MIL-PRF-19500/376F * 4.4.2.1 Group B inspection, table VIa (JANS) of MIL-PRF-19500. Subgroup Method Condition B4 1037 VCB = 10 V dc. B5 1027 VCB = 10 V dc; PD ≥ 100 percent of maximum rated PT (see 1.3). (NOTE: If a failure occurs, resubmission shall be at the test conditions of the original sample.) Option 1: 96 hours minimum sample size in accordance with MIL-PRF-19500, table VIa, adjust TA or PD to achieve TJ = +275°C minimum. Option 2: 216 hours minimum, sample size = 45, c = 0; adjusted TA or PD to achieve a TJ = +225°C minimum. 4.4.2.2 Group B inspection, (JAN, JANTX, and JANTXV). Separate samples may be used for each step. In the event of a group B failure, the manufacturer may pull a new sample at double size from either the failed assembly lot or from another assembly lot from the same wafer lot. If the new “assembly lot” option is exercised, the failed assembly lot shall be scrapped. Step Method 1 1039 Steady-state life: Test condition B, 340 hours, VCB = 10 -30 V dc, TJ = 150°C min., external heating of the device under test to achieve TJ = +150°C minimum is allowed provided that a minimum of 75 percent of rated power is dissipated. No heat sink or forcedair cooling on the devices shall be permitted. n = 45 devices, c = 0. 2 1039 The steady-state life test of step 1 shall be extended to 1,000 hours for each die design. Samples shall be selected from a wafer lot every twelve months of wafer production. Group B, step 2 shall not be required more than once for any single wafer lot. n = 45, c = 0. 3 1032 High-temperature life (non-operating), t = 340 hours, TA = +200°C. n = 22, c = 0. Condition 4.4.2.3 Group B sample selection. Samples selected from group B inspection shall meet all of the following requirements: a. For JAN, JANTX, and JANTXV, samples shall be selected randomly from a minimum of three wafers (or from each wafer in the lot) from each wafer lot. For JANS, samples shall be selected from each inspection lot. See MIL-PRF-19500. b. Must be chosen from an inspection lot that has been submitted to and passed group A, subgroup 2 conformance inspection. When the final lead finish is solder or any plating prone to oxidation at high temperature, the samples for life test (subgroups B4 and B5 for JANS, and group B for JAN, JANTX, and JANTXV) may be pulled prior to the application of final lead finish. 4.4.3 Group C inspection, Group C inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VII of MIL-PRF-19500, and in 4.4.3.1 (JANS) and 4.4.3.2 (JAN, JANTX, and JANTXV) herein for group C testing. Electrical measurements (end-points) shall be in accordance with group A, subgroup 2 herein. Delta requirements shall be in accordance with table III herein. 10 MIL-PRF-19500/376F 4.4.3.1 Group C inspection, table VII (JANS) of MIL-PRF-19500. Subgroup Method C2 2036 Test condition E (not applicable to UA and UB suffix devices). C6 1026 1,000 hours at VCB = 10 - 30 V dc; power shall be applied to achieve TJ = +150°C minimum and a minimum power dissipation PD = 75 percent of maximum rated PT as defined in 1.3 herein. Condition 4.4.3.2 Group C inspection, table VII (JAN, JANTX, and JANTXV) of MIL-PRF-19500. Subgroup Method C2 2036 Test condition E (not applicable to UA and UB suffix devices). C5 3131 See 1.3. C6 Condition Not applicable. 4.4.3.3 Group C sample selection. Samples for subgroups in group C shall be chosen at random from any inspection lot containing the intended package type and lead finish procured to the same specification which is submitted to and passes group A tests for conformance inspection. Testing of a subgroup using a single device type enclosed in the intended package type shall be considered as complying with the requirements for that subgroup. * 4.4.5 Group E inspection. Group E inspection shall be conducted in accordance with the conditions specified for subgroup testing in appendix E, table IX of MIL-PRF-19500 and as specified in table II herein. Electrical measurements (end-points) shall be in accordance with table I, subgroup 2 herein. Delta measurements shall be in accordance with the applicable steps of table III. 4.5 Method of inspection. Methods of inspection shall be as specified in the appropriate tables and as follows. 4.5.1 Pulse measurements. Conditions for pulse measurement shall be as specified in section 4 of MIL-STD-750. 11 MIL-PRF-19500/376F TABLE I. Group A inspection. MIL-STD-750 Limit Symbol Inspection 1/ Min Method Max Unit Conditions Subgroup 1 2/ Visual and mechanical examination 3/ 2071 n = 45 devices, c = 0 Solderability 3/ 4/ 2026 n = 15 leads, c = 0 Resistance to solvents 3/ 4/ 5/ 1022 n = 15 devices, c = 0 Temperature cycling 3/ 4/ 1051 Test condition C, 25 cycles. n = 22 devices, c = 0 Hermetic seal 4/ Fine leak Gross leak 1071 n = 22 devices, c = 0 Electrical measurements 4/ Bond strength 3/ 4/ Group A, subgroup 2 2037 Precondition TA = +250°C at t = 24 hrs or TA = 300°C at t = 2 hrs; n = 11 wires, c = 0 Collector to emitter breakdown voltage 3011 Bias condition D; IC = 10 mA dc pulsed (see 4.5.1) V(BR)CEO Collector to base cutoff current 3036 Bias condition D; VCB = 60 V dc ICBO1 10 µA dc Emitter to base cutoff current 3061 Bias condition D; VEB = 6 V dc IEBO1 10 µA dc Collector to base cutoff current 3036 Bias condition D; VCB = 45 V dc ICBO2 5 nA dc Collector to emitter cutoff current 3041 Bias condition D; VCE = 5 V dc ICEO 2 nA dc Emitter to base cutoff current 3061 Bias condition D; VEB = 5 V dc IEBO2 2 nA dc Collector to emitter cutoff current 3041 Bias condition C; VCE = 45 V dc ICES 5 nA dc Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 1 µA dc hFE1 Subgroup 2 See footnote at end of table. 12 60 45 V dc MIL-PRF-19500/376F TABLE I. Group A inspection - Continued. MIL-STD-750 Method Limit Symbol Inspection 1/ Min Max Unit Conditions Subgroup 2 - continued. Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 10 µA dc hFE2 200 500 Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 100 µA dc hFE3 225 675 Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 500 µA dc hFE4 250 800 Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 1 mA dc hFE5 250 800 Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 10 mA dc pulsed (see 4.5.1) hFE6 225 800 Collector to emitter voltage (saturated) 3071 IC = 1.0 mA dc; IB = 100 µA dc VCE(sat) Base emitter voltage (nonsaturated) 3066 Test condition B; VCE = 5 V dc; IC = 100 µA dc VBE(ON) 0.5 0.3 V dc 0.7 V dc 10 µA dc Subgroup 3 High-temperature operation Collector to base cutoff current TA = +150°C 3036 Low-temperature operation Bias condition D; VCB = 45 V dc ICBO3 TA = -55°C 3076 VCE = 5 V dc; IC = 10 µA dc hFE7 35 Magnitude of common emitter small-signal short-circuit forward-current transfer ratio 3306 VCE = 5 V dc; IC = 50 µA dc; f = 5 MHz |hfe|1 3.0 Magnitude of common emitter small-signal short-circuit forward- current transfer ratio 3306 VCE = 5 V dc; IC = 500 µA dc; f = 30 MHz |hfe|2 2.0 Small-signal open-circuit output admittance 3216 VCE = 5 V dc; IC = 1.0 mA dc; f = 1 kHz hoe 40 Small-signal open- circuit reverse-voltage transfer ratio 3211 VCE = 5 V dc; IC = 1.0 mA dc; f = 1 kHz hre 8.0 x 10-4 Small-signal short- circuit input impedance 3201 VCE = 5 V dc; IC = 1 mA dc; f = 1 kHz hie Forward-current transfer ratio Subgroup 4 See footnote at end of table. 13 3.5 7.0 24 µmhos kΩ MIL-PRF-19500/376F TABLE I. Group A inspection - Continued. MIL-STD-750 Method Limit Symbol Inspection 1/ Min Max 250 900 Unit Conditions Subgroup 4 - continued. Small-signal short- circuit forward current transfer ratio 3206 VCE = 5 V dc; IC = 1 mA dc; f = 1 kHz Open circuit output capacitance 3236 VCB = 5 V dc; IE = 0; 100 kHz ≤ f ≤ 1 MHz Cobo 5.0 pF Input capacitance (output open-circuited) 3240 VEB = 0.5 V dc; IC = 0; 100 kHz ≤ f ≤ 1 MHz Cibo 6.0 pF Noise figure 3246 f = 100 Hz; VCE = 5 V dc; IC = 10 µA dc; Rg = 10 kΩ; NF1 7.5 dB Noise figure 3246 f = 1 kHz; VCE = 5 V dc; IC = 10 µA dc; Rg = 10 kΩ; NF2 3 dB Noise figure 3246 f = 10 kHz; VCE = 5 V dc; IC = 10 µA dc; Rg = 10 kΩ; NF3 2 dB Noise figure (wideband) 3246 Noise bandwidth = 10 Hz to 15.7 kHz; VCE = 5 V dc; IC = 10 µA dc; Rg = 10 kΩ; NF4 3 dB 2075 n = 1 device, c = 0 hfe Subgroups 5 and 6 Not applicable Subgroup 7 4/ Decap internal visual (design verification) 1/ For sampling plan see MIL-PRF-19500. 2/ For resubmission of failed subgroup A1, double the sample size of the failed test or sequence of tests. A failure in group A, subgroup 1 shall not require retest of the entire subgroup. Only the failed test shall be rerun upon submission. 3/ Separate samples may be used. 4/ Not required for JANS devices. 5/ Not required for laser marked devices. 14 MIL-PRF-19500/376F * TABLE II. Group E inspection (all quality levels) - for qualification only. MIL-STD-750 Inspection Method Qualification Conditions 45 devices c=0 Subgroup 1 Temperature cycling (air to air) 1051 Hermetic seal 1071 Test condition C, 500 cycles Fine leak Gross leak Electrical measurements See group A, subgroup 2 and table III herein. Subgroup 2 45 devices c=0 Intermittent life VCB = 10 V dc, 6,000 cycles. Electrical measurements See group A, subgroup 2 and table III herein. Subgroups 3 through 7 Not applicable Subgroup 8 Reverse stability 1033 Condition A for devices ≥ 400 V Condition B for devices ≤ 400 V 15 45 devices c=0 MIL-PRF-19500/376F * TABLE III. Groups B and C delta measurements. 1/ 2/ 3/ 4/ Step Inspection Method MIL-STD-750 Conditions Symbol 5/ ∆hFE4 Limit Unit 1 Forward-current transfer ratio 3076 VCE = 5 V dc; IC = 500 µA dc; pulsed see 4.5.1 2. Collector to emitter voltage (saturated) 3071 IC = 1.0 mA dc; IB = 100 µA dc ∆VCE(sat) 5/ ±50 mV dc change from previously measured value. 3. Collector to emitter cutoff current 3041 Bias condition C; VCE = 45 V dc ∆ICES 5/ 100 percent of initial value or 2 nA dc, whichever is greater. 1/ 2/ 3/ 4/ 5/ ±25 percent change from initial recorded reading The delta measurements for group B, table VIa (JANS) of MIL-PRF-19500 are as follows: a. Subgroup 4, see table III herein, step 2. b. Subgroup 5, see table III herein, steps 1 and 3. The delta measurements for 4.4.2.2 herein (group B, JAN, JANTX, and JANTXV) are as follows: All steps of table III shall be performed after each step in 4.4.2.2 herein. The delta measurements for group C, table VII of MIL-PRF-19500 are as follows: Subgroup 6, see table III herein, steps 1 and 3 for JANS, step 1 for JAN, JANTX, and JANTXV. The delta measurements for group E, table IX of MIL-PRF-19500 are as follows: Subgroups 1 and 2, see table III herein, all steps. Devices which exceed the group A limits for this test shall not be accepted. 16 MIL-PRF-19500/376F 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points' packaging activity within the Military Department or Defense Agency, or within the Military Departments' System Command. Packaging data retrieval is available from the managing Military Departments' or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The notes specified in MIL-PRF-19500 are applicable to this specification. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this specification. b. Issue of DoDISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.2.1). c. Lead formation and finish may be specified (see 3.4.1). d. Type designation and product assurance level. e. Packaging requirements (see 5.1). 6.3 Qualification. With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-19500 whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or orders for the products covered by this specification. Information pertaining to qualification of products may be obtained from Defense Supply Center, Columbus, ATTN: DSCC-VQE, P.O. Box 3990, Columbus, OH 43216-5000. * 6.4 Suppliers of JANHC die. The qualified JANHC suppliers with the applicable letter version (example JANHCA2N2484) will be identified on the QML. JANC ordering information Manufacturer PIN 2N2484 43611 34156 JANHCA2N2484 JANKCA2N2484 JANHCB2N2484 JANKCB2N2484 * 6.5 Changes from previous issue. The margins of this specification are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 17 MIL-PRF-19500/376F Custodians: Army - CR Navy - EC Air Force - 11 NASA - NA DLA - CC Preparing activity: DLA - CC (Project 5961-2497) Review activities: Army - AR, MI, SM Navy - AS, MC, SH Air Force - 19 18 STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL 1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should be given. 2. The submitter of this form must complete blocks 4, 5, 6, and 7. 3. The preparing activity must provide a reply within 30 days from receipt of the form. NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements. I RECOMMEND A CHANGE: 1. DOCUMENT NUMBER MIL-PRF-19500/376F 2. DOCUMENT DATE 15 February 2002 3. DOCUMENT TITLE SEMICONDUCTOR DEVICE, TRANSISTOR, NPN, SILICON, LOW-POWER TYPES 2N2484, 2N2484UA, 2N2484UB, JAN, JANTX, JANTXV, JANS, JANHC, AND JANKC 4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.) 5. REASON FOR RECOMMENDATION 6. SUBMITTER a. NAME (Last, First, Middle initial) c. ADDRESS (Include Zip Code) b. ORGANIZATION d. TELEPHONE (Include Area Code) COMMERCIAL DSN FAX EMAIL 7. DATE SUBMITTED 8. PREPARING ACTIVITY a. Point of Contact Alan Barone c. ADDRESS Defense Supply Center, Columbus ATTN: DSCC-VAC P.O. Box 3990 Columbus, OH 43216-5000 DD Form 1426, Feb 1999 (EG) b. TELEPHONE Commercial DSN FAX EMAIL 614-692-0510 850-0510 614-692-6939 [email protected] IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT: Defense Standardization Program Office (DLSC-LM) 8725 John J. Kingman, Suite 2533 Fort Belvoir, VA 22060-6221 Telephone (703) 767-6888 DSN 427-6888 Previous editions are obsolete WHS/DIOR, Feb 99