AC-DC 130 Watts xppower.com JPS130/JPS130-M Series • High Efficiency - up to 90% • Medical Approval (JPS130-M Versions) • 3” x 5” Footprint • Zero Voltage Switching Technology • High Power Density • 100 W Convection-cooled • Single & Multi Outputs Specification Input Input Voltage Input Frequency Input Current Inrush Current Power Factor Earth Leakage Current Input Protection General • • • • • • 90-264 VAC (130-370 VDC) 47-63 Hz 2.0/1.0 A max at 115/230 VAC 30 A at 115 VAC, 60 A at 230 VAC 0.9 typical 1.5 mA max at 264 VAC/60 Hz JPS130 250 µA max at 240 VAC/60 Hz JPS130-M • Internal 3.15 A/250 V fuse Both line & neutral fused (JPS130-M) Efficiency Isolation Switching Frequency Power Density MTBF • Up to 90% nominal line, full load • 3000 VAC Input to Output (JPS130), 4000 VAC Input to Output (JPS130-M), 1500 VAC Input to Ground, 500 VAC Output to Ground • 120 kHz fixed, ±10% for both active PFC & PWM • 6.7 W/In3 • 250 kHrs per MIL-HDBK-217F at 25 °C Environmental Output Output Voltage Output Voltage Trim • See table • ±10% on single output models, ±5% on multi output models, other voltages will track by the same percentage Initial Set Accuracy • At 60% rated load ±1% single outputs, ±3% on V1 for multi outputs Minimum Load • Single output: no minimum load required Multi-outputs: (see note 1) Start Up Rise Time • <20 ms Hold Up Time • 16 ms typical at low line Line Regulation • ±0.5% Vmin to Vmax Load Regulation • ±1%, ±5% for auxiliaries, 20-100% of rated load Transient Response • 4% max deviation, recovery to within 1% in 500 µs for a 25% load change Ripple & Noise • ±1% max pk-pk (see note 4) Overvoltage Protection • 110-140% on V1 only, recycle input to reset Overload Protection • 110-150%, auto recovery Short Circuit Protection • Trip & restart (Hiccup mode) Temperature • 0.05%/°C Coefficient Remote Sense • Single output models only, compensates for up to 0.5 V drop Fan Output • 12 V, 450 mA multi-output models only Operating Temperature • 0 °C to +70 °C, (see derating curves) Cooling • 130 W with 18 CFM airflow, 100 W with convection cooling Operating Humidity • 5-95% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000 m EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity Radiated Immunity EFT/Burst Surge Conducted Immunity Dips & Interruptions Safety Approvals • EN55022, level B conducted FCC 20780, level B conducted • EN61000-3-2 • EN61000-3-3 • EN61000-4-2, level 3 Perf Criteria A • EN61000-4-3, 10 V/m Perf Criteria A • EN61000-4-4, level 3 Perf Criteria A • EN61000-4-5, level 3 Perf Criteria A • EN61000-4-6, 3 V Perf Criteria A • EN61000-4-11, 30% 10 ms, 60% 100 ms, 95% 5000 ms Perf Criteria A, B, B • JPS130: EN60950-1:2001, UL60950-1, CSA C22.2 No. 60950-1, CE Mark LVD. JPS130-M: UL2601-1, EN60601-1, CSA C22.2 No. 601.1 CE Mark LVD. Output Current Convection-cooled 18 CFM Output Power(3) Output Voltage 100 W 3.3 V 25.0 A 30.0 A 50 mV JPS130PS03^ 5.0 V 20.0 A 26.0 A 50 mV JPS130PS05†^ 12.0 V 9.0 A 10.8 A 120 mV JPS130PS12†^ 15.0 V 7.0 A 8.7 A 120 mV JPS130PS15†^ 24.0 V 4.5 A 5.4 A 200 mV JPS130PS24†^ 48.0 V 2.3 A 2.7 A 200 mV JPS130PS48†^ 130 W 130 W Ripple & Noise Pk-Pk(4) 5.0 V (1) 11.5 A 15.0 A 50 mV 12.0 V (2) 3.0 A 5.0 A 100 mV -12.0 V (2) 0.5 A 0.5 A 100 mV 3.3 V (1) 10.0 A 15.0 A 50 mV 5.0 V (2) 8.0 A 15.0 A 50 mV 12.0 V (2) 0.5 A 0.5 A 100 mV 130 W Model Number JPS130PT31(2)†^ JPS130PT30(2)†^ Notes 1. 20% minimum load required on V1 to maintain stated regulation for auxiliary rails. 2. Load regulation of auxiliary rails is defined over the range of 60% of rated output ±40%. 3. Maximum power with 18 CFM of forced air. 4. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor. 5. Covers available, order part number ‘JPS130 COVER’†^ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 90.6 x 142.9 x 39.8 mm. 6. Connector kits and cable harnesses available. Consult sales for options. † Available from Farnell. See pages 204-206. ^ Available from Newark. See pages 207-208. Mechanical Details All dimensions are in inches (mm). Tolerance: 0.02 (0.4) max. Weight: 0.5 lbs (240 g) approx. 0.225 (5.7) 0.16 (4.0) Dia Mounting Hole (4 Places) 1 N TB1 TB3 2.55 (64.8) 3.00 (76.2) TB2 L See page 29 for TB2 pin connections 1 4.55 (115.6) 5.00 (127.0) To Chassis Grounding x 2 1.18 (30.0)(1) Pin 1 2 TB3 PIN CONNECTIONS Single Output Multi Output - Sense 0V + Sense +12 V Fan 0.10 (2.5) Notes 1. Single output model shown, add extra 0.08” (2.0mm) to overall height for multi-output models. 2. AC input connector (TB1): Molex 5277-02A or equivalent. Mates with 5196-N housings. 3. DC output connector (TB2): Molex 5273 or equivalent, mates with 5195-N and 5239-N housings except JPS130PS03 which has a 6-position terminal screw block: Dinkle part number EHK508V Series accepts 24-12 AWG wire. 4. TB3: Molex 5045-02A or equivalent. Single output units - TB3 is remote sense. Multi-output units - TB3 is 12 V, 450 mA fan output. AC-DC JPS130 Models and Ratings Output Power(3) Output Current Convection-cooled 18 CFM Output Voltage 130 W 130 W 130 W 130 W Ripple & Noise Pk-Pk(4) Model Number 5.0 V 20.0 A 26.0 A 50 mV JPS130PS05-M†^ 12.0 V 9.0 A 10.8 A 120 mV JPS130PS12-M†^ 15.0 V 7.0 A 8.7 A 120 mV JPS130PS15-M†^ 24.0 V 4.5 A 5.4 A 200 mV JPS130PS24-M†^ 28.0 V 3.8 A 4.6 A 200 mV JPS130PS28-M†^ 48.0 V 2.3 A 2.7 A 200 mV JPS130PS48-M†^ 5.0 V (1) 10.0 A 15.0 A 50 mV 12.0 V (2) 3.0 A 4.1 A 120 mV -12.0 V (2) 0.8 A 1.1 A 120 mV 5.0 V (1) 10.0 A 15.0 A 50 mV 15.0 V (2) 2.5 A 4.1 A 150 mV -15.0 V (2) 0.8 A 1.1 A 150 mV 5.0 V (1) 2.5 A 4.0 A 50 mV 24.0 V (2) 2.8 A 4.0 A 240 mV 12.0 V (2) 0.7 A 1.0 A 120 mV JPS130PT31-M(2)†^ JPS130PT32-M(2)†^ JPS130PT34-M(2)† Notes 1. 20% minimum load required on V1 to maintain stated regulation for auxiliary rails. 2. Load regulation of auxiliary rails is defined over the range of 60% of rated output ±40%. 3. Maximum power with 18 CFM of forced air. 4. Ripple and noise measured over 15 MHz bandwidth with a 47 µF electrolytic capacitor and 0.47 µF ceramic capacitor. 5. Covers available, order part number ‘JPS130-M COVER’†^ or add suffix ‘-C’ to receive the unit with cover fitted. Overall dimensions 89.5 x 143.0 x 40.0 mm. 6. Connector kits and cable harnesses available. Consult sales for options. † Available from Farnell. See pages 204-206. ^ Available from Newark. See pages 207-208. Mechanical Details All dimensions are in inches (mm). Tolerance: ± 0.02 (0.4) max. Weight: 0.5 lbs (240 g) approx. 0.20 (5.0) 0.16 (4.0) Dia Mounting Hole (4 Places) 2.60 (66.2) 3.00 (76.2) TB2 L N TB1 See page 29 for TB2 pin connections 1 TB3 1 4.60 (117.0) 5.00 (127.0) To Chassis Grounding x 2 Pin 1 2 1.18 (30.0)(1) AC-DC JPS130-M Models and Ratings TB3 PIN CONNECTIONS Single Output Multi Output - Sense 0V + Sense +12 V Fan 0.10 (2.5) Notes 1. Single output model shown, add extra 0.08” (2.0 mm) to overall height for multi-output models. 2. AC input connector (TB1): Molex 5277-02A or equivalent. Mates with 5196-N housings. 3. DC output connector (TB2): Molex 5273 or equivalent. Mates with 5195-N and 5239-N housings. 4. TB3: Molex 5045-02A or equivalent. Single output units - TB3 is remote sense. Multi-output units - TB3 is 12 V, 450 mA fan output. JPS130 PIN CONNECTIONS TB2 1 2 3 4 5 6 7 8 9 10 Type PS05 +V +V +V +V Return Return Return Return PS03, 12, 15, 24, 48 +V +V +V Return Return Return PT31 +5 V +5 V +5 V Return Return Return Return +12 V -12 V Molex 5273-08A Molex 5273-06A Molex 5273-09A PT30 +3.3 V +3.3 V Return Return Return Return Return +5 V +5 V +12 V Molex 5273-10A JPS130-M PIN CONNECTIONS TB2 1 2 3 4 5 6 7 8 9 Type PS05 Return Return Return Return +V +V +V +V PS12, 15, 24, 28, 48 Return Return Return +V +V +V Molex 5273-08A Molex 5273-06A PT31 -12 V +12 V Return Return Return Return +5 V +5 V +5 V PT32 -15 V +15 V Return Return Return Return +5 V +5 V +5 V Molex 5273-09A PT34 +12 V +24 V Return Return Return Return +5 V +5 V +5 V Derating Curves JPS130 130 A A JPS130 with 18 CFM fan (except JPS130PS03). B JPS130PS12, PS15, PS24 and PS48 with convection cooling. JPS130PS03 with 18 CFM fan. C JPS130PS05, PT30, PT31, PT32 and PT34 with convection cooling. D JPS130PS03 with convection cooling. A JPS130-M with 18 CFM fan. B JPS130PS12-M, PS15-M, PS24-M and PS48-M with convection cooling. C JPS130PS05-M, PT30-M, PT31-M, PT32-M and PT34-M with convection cooling. Load (W) 100 C B D 80 60 40 20 0 -10 0 10 20 30 40 50 60 70 Ambient Temp (˚C) JPS130-M 130 A Load (W) 100 C B 80 60 40 20 0 -10 0 10 20 30 40 50 60 70 Ambient Temp (˚C) 25-Sept-08 AC-DC JPS130/JPS130-M Pin Connections