K1613 Series K1613 Series 14 pin DIP, 3.3 Volt, Sinewave, TCXO 3.3V Voltage Controlled Temperature Compensated Crystal Oscillators Applications: Phase Locked Loops Clocking “Sync” to NTSC Video Standards; Reference Signal; Signal Tracking ±10ppm Stability -40°C to 85°C Op. Temperature “Clipped” Sine Wave Output Non Hermetic Package E L E C T R I C A L S P E C I F I C AT I O N S Model K1613 Frequency Range (MHz) 1 to 25 Input Current (mA) <2 Frequency Control Function (For Custom Deviation Range, Vc Range, etc. - Consult Factory) Voltage Control Included Minimum Deviation (ppm) ±28 Minimum Deviation Sensitivity (ppm/V) +14 Linearity (%) <10 Modulation Bandwidth (3dB) > 20KHz Nominal Control Voltage (V) 2.5 Control Voltage Range (V) 0.3 to 3.0 Manual Adjustment (ppm) ±5 min. Transfer Function Positive Input Impedance > 50KΩ @ 10KHz Frequency Stability (ppm) ±10ppm (Inclusive of Calibration, Temperature, Voltage, Load and 10 yr.Aging) Overall 25oC Calibration ±1ppm Over Operating Temperature ±3ppm Aging 1st Year ±1ppm Temperature Range (oC) -40oC to +85oC -40oC to +85oC +3.3V ±5% Operating Storage Supply Voltage (V) Output (“Clipped” Sine Wave) 1.0V p-p min., 10KΩ/10pF Start Up Time (ms) <10 Typical SSB Phase Noise (dBC/Hz) 10Hz -70 Offset From Carrier 100Hz -95 1KHz -120 10KHz -140 100KHz -150 PA R T N U M B E R I N G G U I D E K1613 - Specify Frequency MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. 2553 N. Edgington Park, datasheets. IL 60131 y Phone: y Fax: 847.451.7585 Please see www.mtronpti.com for ourStreet, complete Franklin offering and detailed Contact us for your847.451.1000 application specific requirements: MtronPTI 1-800-762-8800. 800-888-1499 or www.champtech.com Revision: 12-21-06 K1613 Series K1613 Series 14 pin DIP, 3.3 Volt, Sinewave, TCXO 5V Voltage Controlled Temperature Compensated Crystal Oscillators PIN FUNCTION 1 Voltage Control 7 Gnd/ & Case Gnd 8 Output + VCC 14 TEST CIRCUIT DIAGRAM MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS TEST METHODS REFERENCE PROCEDURES DESCRIPTION Temperature Cycle MIL-STD-833, Mtd 1010, Cond. B -55°C to +125°C; Air-to-Air; 100 cycles; 10 min. dwell Mechanical Shock MIL-STD-883, Mtd 2002, Cond. B 1500 g’s Vibration MIL-STD 883, Mtd 2007, Cond. B 20-2000 Hz; 0.06 inch; 15g’s; 3 planes Humidity Steady State MIL-STD-202, Mtd 103 40°C; 90%-95% R.H.; 56 days Thermal Shock MIL-STD-883, Mtd 1011.7 Cond. B 100°C to 0°C; Water-to-Water; 15 cycles Electrostatic Discharge MIL-STD-883, Mtd 3015 Class II 2 KV to 4 KV Threshold Solderability Hermeticity MIL-STD-883, Mtd 2022.2 MIL-STD-883, Mtd 1014.8, Cond. A1 Solder dip; Meniscograph Criteria Mass spectro. 2 x 10-8 atmos. CC/sec He Resistance to Soldering Lead Integrity MIL-STD-202, Mtd 210A, Cond. C 260°C; 10 seconds: 1 inch/sec. MIL-STD-883, Mtd 2004.5, Cond. A, B1 Lead tension & bend stress Marking Permanence Life Test MIL-STD-883, Mtd 2015.8 MIL-STD-883, Mtd 1005.6 Resistance to solvents 125°C, powered, 1000 hours minimum MtronPTI reserves the right to make changes to the product(s) and service(s) described herein without notice. No liability is assumed as a result of their use or application. 2553 N. Edgington Street, Franklin Park, IL 60131 y Phone: 847.451.1000 y Fax: 847.451.7585 Please see www.mtronpti.com for our complete offering and detailed datasheets. Contact us for your application specific requirements: MtronPTI 1-800-762-8800. 800-888-1499 or www.champtech.com Revision: 12-21-06