128M DDR SDRAM K4D263238D 128Mbit DDR SDRAM 1M x 32Bit x 4 Banks Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL Revision 1.3 July 2002 - 1 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D Revision History Revision 1.3 (July 18, 2002) • Changed power dissipation from 2.0W to 1.8W Revision 1.2 (June 17, 2002) • Removed K4D263238D-QC55 from the spec. • 183/166MHz were supported in K4D263238D-QC50. Revision 1.1 (May 24, 2002) • Removed K4D263238D-QC45/60 from the spec Revision 1.0 (May 20, 2002) • Define DC spec. Revision 0.0 (April 23, 2002)- Target spec • Define target spec. - 2 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D 1M x 32Bit x 4 Banks Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL FEATURES • 2.5V ± 5% power supply • Data I/O transactions on both edges of Data strobe • SSTL_2 compatible inputs/outputs • DLL aligns DQ and DQS transitions with Clock transition • 4 banks operation • Edge aligned data & data strobe output • MRS cycle with address key programs • Center aligned data & data strobe input -. Read latency 3,4 (clock) • DM for write masking only -. Burst length (2, 4, 8 and Full page) • Auto & Self refresh -. Burst type (sequential & interleave) • 32ms refresh period (4K cycle) • Full page burst length for sequential burst type only • 100pin TQFP package • Start address of the full page burst should be even • Maximum clock frequency up to 250MHz • All inputs except data & DM are sampled at the positive • Maximum data rate up to 500Mbps/pin going edge of the system clock • Differential clock input • No Write Interrupted by Read function ORDERING INFORMATION Part NO. Max Freq. Max Data Rate K4D263238D-QC40 250MHz 500Mbps/pin K4D263238D-QC50 200MHz 400Mbps/pin Interface Package SSTL_2 100 TQFP GENERAL DESCRIPTION FOR 1M x 32Bit x 4 Bank DDR SDRAM The K4D263238D is 134,217,728 bits of hyper synchronous data rate Dynamic RAM organized as 4 x 1,048,576 words by 32 bits, fabricated with SAMSUNG′s high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to 2.0GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety of high performance memory system applications. - 3 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D DQ28 VDDQ DQ27 DQ26 VSSQ DQ25 DQ24 VDDQ DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ VSS VDD DQ11 DQ10 VSSQ DQ9 DQ8 VDDQ VREF DM3 DM1 CK CK CKE MCL A8(AP) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 PIN CONFIGURATION (Top View) DQ29 81 50 A7 VSSQ 82 49 A6 DQ30 83 48 A5 DQ31 84 47 A4 VSS 85 46 VSS VDDQ 86 45 A9 N.C 87 44 N.C N.C 88 43 N.C N.C 89 42 N.C N.C 90 41 N.C N.C 91 40 N.C VSSQ 92 39 N.C RFU 93 38 N.C DQS 94 37 A11 VDDQ 95 36 A10 VDD 96 35 VDD DQ0 97 34 A3 DQ1 98 33 A2 VSSQ 99 32 A1 100 31 A0 20 x 14 mm2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 DQ3 DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ DQ16 DQ17 VSSQ DQ18 DQ19 VDDQ VDD VSS DQ20 DQ21 VSSQ DQ22 DQ23 VDDQ DM0 DM2 WE CAS RAS CS BA0 BA1 0.65mm pin Pitch VDDQ DQ2 100 Pin TQFP PIN DESCRIPTION CK,CK Differential Clock Input BA0, BA1 Bank Select Address CKE Clock Enable A0 ~A11 Address Input CS Chip Select DQ0 ~ DQ31 Data Input/Output RAS Row Address Strobe VDD Power CAS Column Address Strobe VSS Ground WE Write Enable VDDQ Power for DQ′s DQS Data Strobe VSSQ Ground for DQ′s DMi Data Mask MCL Must Connect Low RFU Reserved for Future Use - 4 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D INPUT/OUTPUT FUNCTIONAL DESCRIPTION Symbol Type Function Input The differential system clock Input. All of the inputs are sampled on the rising edge of the clock except DQ′s and DM′s that are sampled on both edges of the DQS. CKE Input Activates the CK signal when high and deactivates the CK signal when low. By deactivating the clock, CKE low indicates the Power down mode or Self refresh mode. CS Input CS enables the command decoder when low and disabled the command decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue. RAS Input Latches row addresses on the positive going edge of the CK with RAS low. Enables row access & precharge. CAS Input Latches column addresses on the positive going edge of the CK with CAS low. Enables column access. WE Input Enables write operation and row precharge. Latches data in starting from CAS, WE active. DQS Input/Output Data input and output are synchronized with both edge of DQS. DM0 ~ DM3 Input Data In mask. Data In is masked by DM Latency=0 when DM is high in burst write. DM0 for DQ0 ~ DQ7, DM1 for DQ8 ~ DQ15, DM2 for DQ16 ~ DQ23, DM3 for DQ24 ~ DQ31. DQ0 ~ DQ31 Input/Output Data inputs/Outputs are multiplexed on the same pins. Input Selects which bank is to be active. A0 ~ A11 Input Row/Column addresses are multiplexed on the same pins. Row addresses : RA0 ~ RA11, Column addresses : CA0 ~ CA7. Column address CA8 is used for auto precharge. VDD/VSS Power Supply Power and ground for the input buffers and core logic. VDDQ/VSSQ Power Supply Isolated power supply and ground for the output buffers to provide improved noise immunity. VREF Power Supply Reference voltage for inputs, used for SSTL interface. MCL Must Connect Low Must connect Low CK, CK *1 BA0, BA1 *1 : The timing reference point for the differential clocking is the cross point of CK and CK. For any applications using the single ended clocking, apply VREF to CK pin. - 5 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D BLOCK DIAGRAM (1Mbit x 32I/O x 4 Bank) 32 Intput Buffer I/O Control CK, CK Data Input Register Serial to parallel Bank Select LWE LDMi 64 1Mx32 32 Output Buffer 1Mx32 64 2-bit prefetch Sense AMP Row Decoder Refresh Counter Row Buffer ADDR Address Register CK,CK 1Mx32 x32 DQi 1Mx32 Column Decoder Col. Buffer LCBR LRAS Latency & Burst Length LRAS LCBR Strobe Gen. Programming Register LCKE Data Strobe DLL LWE LCAS LWCBR CK,CK LDMi Timing Register CK,CK CKE CS RAS CAS WE - 6 - DMi Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D FUNCTIONAL DESCRIPTION • Power-Up Sequence DDR SDRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. *1 *1,2 1. Apply power and keep CKE at low state (All other inputs may be undefined) - Apply VDD before VDDQ . - Apply VDDQ before VREF & VTT 2. Start clock and maintain stable condition for minimum 200us. 3. The minimum of 200us after stable power and clock(CK,CK ), apply NOP and take CKE to be high. 4. Issue precharge command for all banks of the device. 5. Issue a EMRS command to enable DLL 6. Issue a MRS command to reset DLL. The additional 200 clock cycles are required to lock the DLL. 7. Issue precharge command for all banks of the device. 8. Issue at least 2 or more auto-refresh commands. 9. Issue a mode register set command with A8 to low to initialize the mode register. *1 The additional 200cycles of clock input is required to lock the DLL after enabling DLL. *2 Sequence of 6&7 is regardless of the order. Power up & Initialization Sequence 6 7 8 9 10 11 tRP 2 Clock min. 2 Clock min. tRP Command ∼ precharge ALL Banks EMRS MRS DLL Reset 1st Auto Refresh precharge ALL Banks 12 - 7 - 14 15 16 tRFC tRFC 200 Clock min. Inputs must be stable for 200us 13 ∼ 5 2nd Auto Refresh ∼ ∼ 4 17 18 19 2 Clock min. Mode Register Set Any Command ∼ ∼ 3 ∼ 2 ∼ ∼ ∼ ∼ 1 0 CK CK Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D MODE REGISTER SET(MRS) The mode register stores the data for controlling the various operating modes of DDR SDRAM. It programs CAS latency, addressing mode, burst length, test mode, DLL reset and various vendor specific options to make DDR SDRAM useful for variety of different applications. The default value of the mode register is not defined, therefore the mode register must be written after EMRS setting for proper operation. The mode register is written by asserting low on CS, RAS, CAS and WE(The DDR SDRAM should be in active mode with CKE already high prior to writing into the mode register). The state of address pins A0 ~ A11 and BA0, BA1 in the same cycle as CS, RAS, CAS and WE going low is written in the mode register. Minimum two clock cycles are requested to complete the write operation in the mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. The mode register is divided into various fields depending on functionality. The burst length uses A0 ~ A2, addressing mode uses A3, CAS latency(read latency from column address) uses A4 ~ A6. A7 is used for test mode. A8 is used for DLL reset. A7,A8, BA0 and BA1 must be set to low for normal MRS operation. Refer to the table for specific codes for various burst length, addressing modes and CAS latencies. BA1 BA0 RFU 0 A11 A10 A9 RFU A8 A7 DLL TM A6 A5 A4 A3 CAS Latency A2 BT A1 A0 Burst Length Address Bus Mode Register Burst Type Test Mode DLL A8 DLL Reset A3 Type A7 mode 0 Sequential 1 Interleave 0 No 0 Normal 1 Yes 1 Test Burst Length CAS Latency BA0 A2 A1 A0 Sequential Interleave 0 Reserve Reserve 0 1 2 2 0 1 0 4 4 3 0 1 1 8 8 0 4 1 0 0 Reserve Reserve 0 1 Reserved 1 0 1 Reserve Reserve 1 1 0 Reserved 1 1 0 Reserve Reserve 1 1 1 Reserved 1 1 1 Full page Reserve A n ~ A0 A6 A5 A4 Latency 0 MRS 0 0 0 Reserved 0 0 1 EMRS 0 0 1 Reserved 0 0 1 0 Reserved 0 1 1 1 0 1 * RFU(Reserved for future use) should stay "0" during MRS cycle. Burst Type MRS Cycle 0 1 2 3 4 5 6 7 8 CK, CK Command NOP Precharge All Banks NOP NOP MRS NOP Any Command NOP NOP tMRD=2 tCK tRP *1: MRS can be issued only at all banks precharge state. *2: Minimum tRP is required to issue MRS command. - 8 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D EXTENDED MODE REGISTER SET(EMRS) The extended mode register stores the data for enabling or disabling DLL and selecting output driver strength. The default value of the extended mode register is not defined, therefore the extend mode register must be written after power up for enabling or disabling DLL. The extended mode register is written by asserting low on CS, RAS, CAS, WE and high on BA0(The DDR SDRAM should be in all bank precharge with CKE already high prior to writing into the extended mode register). The state of address pins A0, A2 ~ A5, A7 ~ A11 and BA1 in the same cycle as CS, RAS, CAS and WE going low are written in the extended mode register. A1 and A6 are used for setting driver strength to weak or matched impedance. Two clock cycles are required to complete the write operation in the extended mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. A0 is used for DLL enable or disable. “High” on BA0 is used for EMRS. All the other address pins except A0,A1,A6 and BA0 must be set to low for proper EMRS operation. Refer to the table for specific codes. BA1 BA0 RFU 1 A11 A10 A9 A8 A7 RFU A6 A5 A4 D.I.C BA0 An ~ A0 A6 A1 0 MRS 0 1 1 EMRS 1 1 A3 A2 RFU A1 A0 Address Bus D.I.C DLL Extended Mode Register A0 DLL Enable Weak 0 Enable Matched 1 Disable Output Driver Impedance Control * RFU(Reserved for future use) should stay "0" during EMRS cycle. Figure 7. Extend Mode Register set - 9 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Unit VIN, VOUT -0.5 ~ 3.6 V Voltage on VDD supply relative to Vss VDD -1.0 ~ 3.6 V Voltage on VDD supply relative to Vss VDDQ -0.5 ~ 3.6 V Storage temperature TSTG -55 ~ +150 °C Power dissipation PD 1.8 W Short circuit current IOS 50 mA Voltage on any pin relative to Vss Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. POWER & DC OPERATING CONDITIONS(SSTL_2 In/Out) Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 65°C) Parameter Symbol Min Typ Max Unit Note Device Supply voltage VDD 2.375 2.50 2.625 V 1 Output Supply voltage VDDQ 2.375 2.50 2.625 V 1 Reference voltage VREF 0.49*VDDQ - 0.51*VDDQ V 2 Termination voltage Vtt VREF-0.04 VREF VREF+0.04 V 3 Input logic high voltage VIH VREF+0.15 - VDDQ+0.30 V 4 Input logic low voltage VIL -0.30 - VREF-0.15 V 5 Output logic high voltage VOH Vtt+0.76 - - V IOH=-15.2mA Output logic low voltage VOL - - Vtt-0.76 V IOL=+15.2mA Input leakage current IIL -5 - 5 uA 6 Output leakage current IOL -5 - 5 uA 6 Note : 1. Under all conditions VDDQ must be less than or equal to VDD. 2. VREF is expected to equal 0.50*VDDQ of the transmitting device and to track variations in the DC level of the same. Peak to peak noise on the VREF may not exceed + 2% of the DC value. Thus, from 0.50*VDDQ, VREF is allowed + 25mV for DC error and an additional + 25mV for AC noise. 3. Vtt of the transmitting device must track VREF of the receiving device. 4. VIH(max.)= VDDQ +1.5V for a pulse and it which can not be greater than 1/3 of the cycle rate. 5. VIL(min.)= -1.5V for a pulse width and it can not be greater than 1/3 of the cycle rate. 6. For any pin under test input of 0V ≤ VIN ≤ VDD is acceptable. For all other pins that are not under test VIN=0V. - 10 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D DC CHARACTERISTICS Recommended operating conditions Unless Otherwise Noted, TA=0 to 65°C) Version Parameter Symbol Unit Note 1 Test Condition -40 -50 Operating Current (One Bank Active) ICC1 Burst Lenth=2 tRC ≥ tRC(min) IOL=0mA, tCC= tCC(min) 245 215 mA Precharge Standby Current in Power-down mode ICC2P CKE ≤ VIL(max), tCC= tCC(min) 70 60 mA Precharge Standby Current in Non Power-down mode ICC2N 100 90 mA Active Standby Current power-down mode ICC3P 100 80 mA Active Standby Current in in Non Power-down mode ICC3N 175 150 mA 630 530 mA 250 230 mA CKE ≥ VIH(min), CS ≥ VIH(min), tCC= tCC(min). CKE ≤ VIL(max), tCC= tCC(min) CKE ≥ VIH(min), CS ≥ VIH(min), tCC= tCC(min) . Operating Current ( Burst Mode) ICC4 Refresh Current ICC5 tRC ≥ tRFC(min) Self Refresh Current ICC6 CKE ≤ 0.2V IOL=0mA ,tCC= tCC(min), Page Burst, All Banks activated. 3 2 mA Note: 1. Measured with outputs open. 2. Refresh period is 32ms. AC INPUT OPERATING CONDITIONS Recommended operating conditions(Voltage referenced to VSS=0V, VDD/ VDDQ=2.5V+ 5%, TA=0 to 65°C) Parameter Symbol Min Typ Max Unit Note Input High (Logic 1) Voltage; DQ VIH VREF+0.35 - - V Input Low (Logic 0) Voltage; DQ VIL - - VREF-0.35 V Clock Input Differential Voltage; CK and CK VID 0.7 - VDDQ+0.6 V 1 Clock Input Crossing Point Voltage; CK and CK VIX 0.5*VDDQ-0.2 - 0.5*VDDQ+0.2 V 2 Note : 1. VID is the magnitude of the difference between the input level on CK and the input level on CK 2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same - 11 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D AC OPERATING TEST CONDITIONS (VDD/ VDDQ=2.5V+ 5% , TA= 0 to 65°C) Parameter Value Unit Input reference voltage for CK(for single ended) 0.50*VDDQ V CK and CK signal maximum peak swing 1.5 V CK signal minimum slew rate 1.0 V/ns VREF+0.35/VREF-0.35 V VREF V Vtt V Input Levels(VIH/VIL) Input timing measurement reference level Output timing measurement reference level Output load condition Note See Fig.1 Vtt=0.5*VDDQ RT=50Ω Output Z0=50Ω VREF =0.5*VDDQ CLOAD=30pF (Fig. 1) Output Load Circuit CAPACITANCE (VDD=2.5V, TA= 25°C, f=1MHz) Parameter Symbol Min Max Unit Input capacitance( CK, CK ) CIN1 1.0 5.0 pF Input capacitance(A0~A10, BA0~BA1) CIN2 1.0 4.0 pF Input capacitance ( CKE, CS, RAS,CAS, WE ) CIN3 1.0 4.0 pF Data & DQS input/output capacitance(DQ0~DQ31) COUT 1.0 6.0 pF Input capacitance(DM0 ~ DM3) CIN4 1.0 6.0 pF DECOUPLING CAPACITANCE GUIDE LINE Recommended decoupling capacitance added to power line at board. Parameter Symbol Value Unit Decoupling Capacitance between VDD and VSS CDC1 0.1 + 0.01 uF Decoupling Capacitance between VDDQ and VSSQ CDC2 0.1 + 0.01 uF Note : 1. VDD and VDDQ pins are separated each other. All VDD pins are connected in chip. All VDDQ pins are connected in chip. 2. VSS and VSSQ pins are separated each other All VSS pins are connected in chip. All VSSQ pins are connected in chip. - 12 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D AC CHARACTERISTICS Parameter CL=3 CL=4 CK cycle time -40 Symbol tCK tCH tCL tDQSCK tAC tDQSQ tRPRE tRPST tDQSS tWPRES tWPREH tWPST tDQSH tDQSL tIS tIH tDS tDH CK high level width CK low level width DQS out access time from CK Output access time from CK Data strobe edge to Dout edge Read preamble Read postamble CK to valid DQS-in DQS-In setup time DQS-in hold time DQS write postamble DQS-In high level width DQS-In low level width Address and Control input setup Address and Control input hold DQ and DM setup time to DQS DQ and DM hold time to DQS -50 Unit Min Max Min Max 4.0 8 5.0 10 ns ns 0.45 0.55 0.45 0.55 tCK 0.45 0.55 0.45 0.55 tCK -0.6 0.6 -0.7 +0.7 ns -0.6 0.6 -0.7 +0.7 ns - 0.4 - +0.45 ns 0.9 1.1 0.9 1.1 tCK 0.4 0.6 0.4 0.6 tCK 0.85 1.15 0.8 1.2 tCK 0 - 0 - ns 0.35 - 0.25 - tCK 0.4 0.6 0.4 0.6 tCK 0.4 0.6 0.4 0.6 tCK 0.4 0.6 0.4 0.6 tCK 0.9 - 1.0 - ns 0.9 - 1.0 - ns 0.4 - 0.45 - ns 0.4 Clock half period tHP tCLmin or tCHmin Data output hold time from DQS tQH tHP-0.4 Note 1 - 0.45 - ns - tCLmin or tCHmin - ns 1 - tHP-0.45 - ns 1 Simplified Timing @ BL=2, CL=3 tCH tCL tCK 0 1 3 2 4 6 5 7 8 CK, CK tIS CS tIH tDQSCK tDQSS DQS tRPST tRPRE tWPRES tDQSQ tDQSH tWPST tWPREH Hi-Z tDS tDH tAC DQ Da1 Db0 Da2 Db1 Hi-Z DM WRITEB COMMAND READA - 13 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D Note 1 : - The JEDEC DDR specification currently defines the output data valid window(tDV) as the time period when the data strobe and all data associated with that data strobe are coincidentally valid. - The previously used definition of tDV(=0.35tCK) artificially penalizes system timing budgets by assuming the worst case output valid window even then the clock duty cycle applied to the device is better than 45/55% - A new AC timing term, tQH which stands for data output hold time from DQS is defined to account for clock duty cycle variation and replaces tDV - tQHmin = tHP-X where . tHP=Minimum half clock period for any given cycle and is defined by clock high or clock low time(tCH,tCL) . X=A frequency dependent timing allowance account for tDQSQmax tQH Timing (CL3, BL2) tHP 0 1 2 3 4 5 CK, CK CS DQS tDQSQ(max) tQH tDQSQ(max) Da0 DQ COMMAND Da1 READA - 14 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D AC CHARACTERISTICS (I) Parameter Symbol -40 -50 Min Max Min Max Unit Row cycle time tRC 15 - 12 - tCK Refresh row cycle time 17 - 14 - 10 100K 8 100K 5 - 4 - Mode register set cycle time tRFC tRAS tRCDRD tRCDWR tRP tRRD tWR tCDLR tCCD tMRD Auto precharge write recovery + Precharge tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK tCK Exit self refresh to read command Row active time RAS to CAS delay for Read RAS to CAS delay for Write Row precharge time Row active to Row active Last data in to Row precharge Last data in to Read command Col. address to Col. address Power down exit time Refresh interval time 3 2 5 - 4 - 3 - 2 - 3 - 2 - 2 - 2 - 1 - 1 - 2 - 2 - tDAL 8 - 6 - tXSR tPDEX tREF 200 - 200 - 1tCK+tIS - 1tCK+tIS 7.8 - 7.8 - Note 1 1 tCK ns us Note :1 For normal write operation, even numbers of Din are to be written inside DRAM - 15 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D (Unit : Number of Clock) AC CHARACTERISTICS (II) K4D263238D-QC40 Frequency Cas Latency 250MHz ( 4.0ns ) 4 200MHz ( 5.0ns ) 3 tRC 15 12 tRFC 17 14 tRAS 10 8 tRCDRD tRCDWR 5 3 4 2 tRP 5 4 tRRD 3 2 tDAL 8 6 Unit K4D623238F-QC50 Frequency Cas Latency 200MHz ( 5.0ns ) 3 183MHz ( 5.5ns ) 3 166MHz ( 6.0ns ) 3 tRC 12 12 10 tRFC 14 14 12 tRAS 8 8 7 tRCDRD tRCDWR 4 2 4 2 3 2 tRP 4 4 3 tRRD 2 2 2 tDAL 6 6 5 Unit tCK tCK tCK tCK tCK * 183/166MHz were supported in K4D263238D-QC50 - 16 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D Simplified Timing(2) @ BL=4, CL=3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 CK, CK BA[1:0] BAa A8/AP Ra ADDR (A0~A7, A9~,A11) Ra BAa BAa Ca BAa BAb Ra Rb Ra Rb BAa BAb Ca Cb WE DQS Da0 Da1 Da2 Da3 DQ Da0 Da1 Da2 Da3 Db0 Db1 Db2 Db3 DM COMMANDACTIVEA WRITEA PRECH ACTIVEA ACTIVEB WRITEA WRITEB tRCD tRAS tRP tRC Normal Write Burst (@ BL=4) tRRD Multi Bank Interleaving Write Burst (@ BL=4) - 17 - Rev. 1.3 (Jul. 2002) 128M DDR SDRAM K4D263238D PACKAGE DIMENSIONS (TQFP) Dimensions in Millimeters 0 ~ 7° 17.20 ± 0.20 14.00 ± 0.10 #100 #1 23.20 ± 0.20 0.575 20.00 ± 0.10 0.825 0.30 ± 0.08 0.13 MAX 0.65 0.09~0.20 1.00 ± 0.10 1.20 MAX * 0.10 MAX 0.05 MIN 0.80 ± 0.20 - 18 - Rev. 1.3 (Jul. 2002)