LM107,LM207,LM307 LM107 LM207 LM307 Operational Amplifiers Literature Number: SNOSBS4A LM107/LM207/LM307 Operational Amplifiers General Description Connection Diagrams Features Y Y Y Y Offset voltage 3 mV maximum over temperature Input current 100 nA maximum over temperature Offset current 20 nA maximum over temperature Guaranteed drift characteristics et Dual-in-Line Package bs ol Metal Can Package tors. Further, replacing circuits where matched transistor pairs buffer the inputs of conventional IC op amps, it can give lower offset voltage and drift at a lower cost. The LM107 is guaranteed over a b55§ C to a 125§ C temperature range, the LM207 from b25§ C to a 85§ C and the LM307 from 0§ C to a 70§ C. e The LM107 series are complete, general purpose operational amplifiers, with the necessary frequency compensation built into the chip. Advanced processing techniques make the input currents a factor of ten lower than industry standards like the 709. Yet, they are a direct, plug-in replacement for the 709, LM101A and 741. The LM107 series offers the features of the LM101A, which makes its application nearly foolproof. In addition, the device provides better accuracy and lower noise in high impedance circuitry. The low input currents also make it particularly well suited for long interval integrators or timers, sample and hold circuits and low frequency waveform genera- TL/H/7757 – 2 Note: Pin 4 connected to case. Top View TL/H/7757 – 3 Top View Order Number LM107H/883* See NS Package Number H08C Order Number LM107J/883* or LM207J See NS Package Number J08A Order Number LM307N See NS Package Number N08A O Dual-in-Line Package TL/H/7757 – 13 Order Number LM107J-14/883* See NS Package Number J14A *Available per SMDÝ 5962-8958901. C1995 National Semiconductor Corporation TL/H/7757 RRD-B30M115/Printed in U. S. A. LM107/LM207/LM307 Operational Amplifiers December 1994 Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Note 4) Supply Voltage Power Dissipation (Note 1) Differential Input Voltage Input Voltage (Note 2) Output Short Circuit Duration Operating Temperature Range (TA) (LM107) (LM207) Storage Temperature Range Lead Temperature (Soldering, 10 sec) LM107/LM207 g 22V 500 mW g 30V g 15V Continuous LM307 g 18V 500 mW g 30V g 15V Continuous b 55§ C to a 125§ C b 25§ C to a 85§ C b 65§ C to a 150§ C 0§ C to a 70§ C b 65§ C to a 150§ C 260§ C 260§ C TMIN TMAX b 55§ C b 25§ C a 125§ C a 85§ C a 70§ C LM107 LM207 LM307 0§ C ESD rating to be determined. Electrical Characteristics (Note 3) LM107/LM207 Conditions Min LM307 Units e Parameter Typ Max Min Typ Max TA e 25§ C, RS s 50 kX 0.7 2.0 2.0 7.5 mV Input Offset Current TA e 25§ C 1.5 10 3.0 50 nA Input Bias Current TA e 25§ C 30 75 70 250 nA Input Resistance TA e 25§ C Supply Current TA e 25§ C VS e g 20V VS e g 15V TA e 25§ C, VS e g 15V VOUT e g 10V, RL t 2 kX Input Offset Voltage RS s 50 kX 1.5 4.0 1.8 2.0 50 160 25 3.0 15 Average Temperature Coefficient of Input Offset Current 25§ C s TA s TMAX TMIN s TA s 25§ C 0.01 0.02 0.1 0.2 TA e a 125§ C, VS e g 20V 1.2 O 100 2 2.5 mA mA V/mV 10 mV 6.0 30 mV/§ C 70 nA 0.01 0.02 0.3 0.6 nA/§ C nA/§ C 20 Input Bias Current 3.0 160 3.0 Input Offset Current MX 3.0 1.8 Average Temperature Coefficient of Input Offset Voltage Supply Current 0.5 bs ol Large Signal Voltage Gain et Input Offset Voltage 300 nA mA Electrical Characteristics (Note 3) (Continued) Parameter LM107/LM207 Conditions Min Large Signal Voltage Gain Output Voltage Swing Input Voltage Range VS e g 15V, VOUT e g 10V RL t 2 kX VS RL RL e g 15V e 10 kX e 2 kX VS e g 20V VS e g 15V Typ LM307 Max Min Typ Units Max 15 25 V/mV g 12 g 14 g 12 g 14 g 10 g 13 g 10 g 13 a 15 b 13 g 12 a 15 b 13 V V g 15 V V Common Mode Rejection Ratio RS s 50 kX 80 96 70 90 dB Supply Voltage Rejection Ratio RS s 50 kX 80 96 70 96 dB e Note 1: The maximum junction temperature of the LM107 is 150§ C, and the LM207/LM307 is 100§ C. For operating at elevated temperatures, devices in the H08 package must be derated based on a thermal resistance of 165§ C/W, junction to ambient, or 30§ C/W, junction to case. The thermal resistance of the dual-in-line package is 100§ C/W, junction to ambient. Note 2: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage. Note 3: These specifications apply for g 5V s VS s a 20V and b 55§ C s TA s a 125§ C for the LM107 or b 25§ C s TA a 85§ C for the LM207, and 0§ C s TA s a 70§ C and g 5V s VS s g 15V for the LM307 unless otherwise specified. O bs ol Schematic Diagram* et Note 4: Refer to RETS107X for LM107H and LM107J military specifications. *Pin connections shown are for metal can. TL/H/7757 – 1 3 Guaranteed Performance Characteristics LM107/LM207 Input Voltage Range Output Swing Voltage Gain TL/H/7757 – 4 Guaranteed Performance Characteristics LM307 Output Swing Voltage Gain et e Input Voltage Range bs ol TL/H/7757 – 5 Typical Performance Characteristics O Supply Current Current Limiting Voltage Gain Input Current Input Noise Voltage Input Noise Current TL/H/7757 – 6 4 Typical Performance Characteristics Open Loop Frequency Response (Continued) Large Signal Frequency Response Voltage Follower Pulse Response TL/H/7757 – 7 Typical Applications** RIN e R1 R2 VIN R1 et VOUT e b Non-Inverting AC Amplifier e Inverting Amplifier VOUT e R1 a R2 VIN R1 RIN e R3 TL/H/7757 – 8 bs ol R3 e R1//R2 Non-Inverting Amplifier VOUT e R1 a R2 VIN R1 O TL/H/7757 – 10 **Pin connections shown are for metal can. 5 TL/H/7757 – 9 Typical Applications** (Continued) Turntable Notch Filter R1 e R2 e R3 R4 e R5 e fo e R1 2 1 2q0C1 C2 R4 R5 et e e 60 Hz TL/H/7757 – 11 O bs ol Differential Input Instrumentation Amplifier TL/H/7757 – 12 **Pin connections shown are for metal can. 6 7 e et bs ol O et e Physical Dimensions inches (millimeters) O bs ol Metal Can Package (H) Order Number LM107H/883 NS Package Number H08C 8 et e Physical Dimensions inches (millimeters) (Continued) O bs ol Ceramic Dual-In-Line Package (J) Order Number LM107J/883 or LM207J NS Package Number J08A Ceramic Dual-In-Line Package (J) Order Number LM107J-14/883 NS Package Number J14A 9 e et LM107/LM207/LM307 Operational Amplifiers Physical Dimensions inches (millimeters) (Continued) bs ol Molded Dual-In-Line Package (N) Order Number LM307N NS Package Number N08E LIFE SUPPORT POLICY O NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated