NSC LM1204V

LM1204 150 MHz RGB Video Amplifier System
General Description
Features
The LM1204 is a triple 150 MHz video amplifier system
designed specifically for high resolution RGB video display
applications. In addition to three matched video amplifiers,
the LM1204 contains a DC operated contrast control, a DC
operated drive control for each amplifier, and a dual clamping system for both brightness control and video blanking.
The LM1204 also contains a back porch clamp pulse generator which is activated by an externally supplied g H/HV
sync signal or by an external composite video signal. The
g H/HV sync input will have priority over the composite video input. A single bH/HV sync output is provided for the
automatically selected sync input signal. The back porch
clamp pulse width is user adjustable from 0.3 ms to 4 ms.
The LM1204 video output stage will directly drive most
Hybrid or discrete CRT amplfier input stages without the
need for an external buffer transistor. The device has been
designed to operate from a 12V supply with all DC controls
operating over a 0V to 4V range providing for an easy interface to serial digital buss controlled monitors.
Y
Y
Y
Y
Y
Y
Built-in video blanking function
Built-in sync separator for composite video input
Includes DC restoration of video signals
Back porch clamp pulse width user adjustable
DC control of brightness, contrast, blanking level, drive
and cutoff
DC controls are 0V to 4V for easy interfacing to a
digitally controlled system
Key Specifications
Y
Y
Y
Y
150 MHz large signal bandwidth (typ)
2.3 ns rise/fall times (typ)
0.1 dB contrast tracking (typ)
g 3 dB drive (D gain) adjustments on R, G, B channels
(typ)
Applications
Y
Y
Y
High resolution CRT monitors
Video AGC amplifier
Wideband amplifier with gain and DC offset control
Block Diagram and Connection Diagram
Top View
TL/H/11238 – 1
Ordering Information
Order Number LM1204V
See NS Package Number V44A
C1995 National Semiconductor Corporation
TL/H/11238
RRD-B30M115/Printed in U. S. A.
LM1204 150 MHz RGB Video Amplifier System
December 1994
Absolute Maximum Ratings
(Note 1)
Thermal Resistance, iJA
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
52 § C/W
Junction Temperature, TJ
150§ C
ESD Susceptibility (Note 4)
Storage Temperature
Lead Temperature
Vapor Phase (60 seconds)
Infrared (15 seconds)
Supply Voltage, VCC
Pins 2, 4, 6, 19, 31, 41, 44 (Note 3)
13.5V
Peak Video Output Source Current
(Any One Amplifier) Pins 30, 35 or 39
30 mA
Voltage at Any Input Pin, VIN
GND s VIN s VCC
Maximum g H Sync Input Voltage
5.5 VPP
Power Dissipation, PD (Above 25§ C
Derate Based on iJA and TJ)
2.4W
2.5 kV
b 65§ C to 150§ C
215§ C
220§ C
Operating Ratings (Note 2)
Temperature Range
0§ C to 70§ C
10.8V s VCC s 13.2V
Supply Voltage, VCC
DC Electrical Characteristics (Video Amplifier Section)
The following specifications apply for VCC (pins 2, 4, 6, 19, 31, 36, 41 and 44) e 12V and TA e 25§ C unless otherwise specified.
S1 e B, S2 e B, S3, 4, 5 closed, V9, 13, 15 e 2V, V20, 21, 22, 24, 43 e 0.5V unless otherwise specified; see test circuit,
Figure 1 .
Symbol
Parameter
Conditions
IS
Supply Current
No Video or Sync Input
Signals, S1 e A
IB
Input Bias Current
(Pin 9, 13, 15, 20, 21 or 22)
S1 e A
I24h
Blank Gate Input High Current
V24 e 4V
I24l
Blank Gate Input Low Current
V24 e 0V
IFB
Feedback Input Current
(Pin 28, 33 or 38)
IBlank a
IBlankb
IBB
Typical
(Note 5)
Limit
(Note 6)
Units
100
125
mA
(Max)
0.3
2
mA
(Max)
0.01
2
mA
(Max)
2
5
mA
(Max)
150
nA
Blank Cap Charge Current
V32,37,42 e 0V
185
75
mA (Min)
Blank Cap Discharge Current
V32,37,42 e 5V
b 185
b 75
mA (Min)
Blank Cap Bias Current (Pins 32, 37, 42)
20
nA
IClamp a
Clamp Cap Charge Current
V5,10,14 e 0V
185
75
mA (Min)
IClampb
Blank Cap Discharge Current
V5,10,14 e 5V
b 185
b 75
mA (Min)
2
V (Min)
0.8
V (Max)
2
50
mV
(Max)
ICB
Clamp Cap Bias Current (Pins 5, 10, 14)
20
nA
V24h
Blank Gate High Input Voltage
Input Signal is Not Blanked
V24l
Blank Gate Low Input Voltage
Input Signal is Blanked
Blank Comparator Offset Voltage
Voltage between V43 and
Any One Video Output
VH
Video Output High Voltage
(Pins 30, 35, 40)
RL e 350X
V28, 33, 38 e 0V
8.7
7
V(Min)
VL
Video Output Low Voltage
(Pins 30, 35, 40)
RL e 350X
V28, 33, 38 e 4V
0.1
0.5
V(Max)
VCM43
Common Mode Range of Blank
Comparator (Pins 43, 28, 33, 38)
0.5
V(Min)
4
V(Max)
2
DC Electrical Characteristics (Sync Separator/Processor Section)
The following specifications apply for VCC (Pins 2, 4, 6, 19, 31, 36, 41 and 44) e 12V and TA e 25§ C, unless otherwise
specified. S1 e B, S2 e B, S3, 4, 5 closed, V9, 13, 15 e 2V, V20, 21, 22, 24, 43 e 0.5V, unless otherwise specified; see Test
Circuit Figure 1 .
Typical
(Note 5)
Limit
(Note 6)
Units
b H Sync Output Logic High (Pin 26)
4.2
2.4
V(Min)
b H Sync Output Logic Low (Pin 26)
0.1
0.4
V(Max)
Symbol
Parameter
b H VOH
b H VOL
V23
Quiescent DC Voltage at g H
Sync Input
Conditions
3
V
AC Electrical Characteristics (Video Amplifier Section)
The following specifications apply for VCC (Pins 2, 4, 6, 19, 31, 36, 41 and 44) e 12V and TA e 25§ C, unless otherwise
specified. S1 e B, S2 e B, S3, 4, 5 closed, V9, 13, 15, 21, 24, 43 e 4V, V20 e 2V, unless otherwise specified; see Test Circuit
Figure 1 .
Symbol
Parameter
RIN
Video Amplifier Input Resistance
AVmax
Maximum Video Amplifier Gain
DAVtrack
Amplifier Gain (Contrast)
Tracking (Note 7)
DAV2V
Attenuation at 2V
DAV0.5V
Conditions
Typical
(Note 5)
Limit
(Note 6)
Units
5.5
V/V(Min)
20
fIN e 12 kHz
10
kX
0.1
dB
Ref: AVmax V21 e 2V
6
dB
Attenuation at 0.5V
Ref: AVmax V21 e 0.5V
28
DGain
D Gain Range (Pins 9, 13, 15)
V9, 13, 15 e 0V to 4V
DVO
Max Brightness Tracking Error (Note 8)
fb3 dB
Video Amplifier Bandwidth (Note 9)
THD
20
dB(Min)
g3
dB
100
mV
VOUT e 3.5 VPP
150
MHz
Video Amplifier Distortion
VOUT e 1 VPP, f e 12 kHz
0.3
%
tR
Video Output Rise Time (Note 9)
Square Wave Input
VOUT e 3.5 VPP, RL e 350X
2.0
ns
tF
Video Output Fall Time (Note 9)
Square Wave Input
VOUT e 3.5 VPP, RL e 350X
2.3
ns
VISO (1 MHz)
Video Amplifier 1 MHz
Isolation (Notes 9, 10)
b 50
dB
VISO (130 MHz)
Video Amplifier 130 MHz
Isolation (Notes 9, 10)
b 10
dB
3
AC Electrical Characteristics (Sync Separator/Processor Section)
The following specifications apply for VCC (Pins 2, 4, 6, 19, 31, 36, 41 and 44) e 12V and TA e 25§ C, unless otherwise
specified. S1 e A, S2 e B, S3, 4, 5 closed, V9, 13, 15, 20, 21, 43 e 2V, unless otherwise specified; see Test Circuit Figure 1
and Timing Diagram for input waveform.
Symbol
V18(Min)
V18(Max)
V23
Parameter
Conditions
Composite Video Input Voltage
(Pin 18)
Composite Video Input Voltage
(Pin 18)
S2 e A, Input e 10% Duty
Cycle, Test for Loss of BP
Pulse at Pin 26
g H Sync Input Voltage (Pin 23)
Input e 10% Duty Cycle
Back Porch Clamp Pulse Width
at V24 e 1V
Back Porch Clamp Pulse Width
at V24 e 4V
S2 e A, Pin 26 e BP Output
Maximum g H Sync Input Frequency
DHI
Max Duty Cycle of Active High
H Sync (Pin 23)
Max Duty Cycle of Active Low
H Sync (Pin 23)
Test for Loss of Sync
at Pin 26
tpdl1
g H Sync Input to b H Sync
Output Low Delay
Input e 10% Duty Cycle
tpdh1
g H Sync Input to b H Sync
Output High Delay
Input e 10% Duty Cycle
tpd1
g H Sync Input Trailing Edge to
Back Porch Clamp Output Delay
Input e 10% Duty Cycle,
S2 e A
tpdl2
Composite Video Input to bH
Sync Output Low Delay
Input e 10% Duty Cycle
tpdh2
Composite Video Input to bH
Sync Output High Delay
Input e 10% Duty Cycle
tpd2
Composite Video Input Trailing
Edge to Back Porch Clamp Output Delay
Input e 10% Duty Cycle
S2 e A
tpdl2 – tpdl1
Composite Video and g H Sync Input
to bH Sync Output Delta Delay
Input e 10% Duty Cycle
DLO
Typical
(Note 5)
Limit
(Note 6)
0.15
2
1.6
1
1.4
300
600
Units
VPP
(Min)
VPP
(Max)
VPP
(Min)
ms
(Max)
ns
(Max)
600
KHz
22
%
22
%
100
ns
65
ns
70
ns
106
ns
68
ns
78
ns
6
ns
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Note 2: Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications
and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics
may degrade when the device is not operated under the listed test conditions.
Note 3: VCC supply pins 2, 4, 6, 19, 31, 36, 41 and 44 must be externally wired together to prevent internal damage during VCC power on/off cycle.
Note 4: Human body model, 100 pF discharged through a 1.5 kX resistor.
Note 5: Typical specifications are specified at a 25§ C and represent the most likely parametric norm.
Note 6: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 7: DAV tracking is a measure of the ability of any two amplifiers to track each other and quantifies the matching of the three attenuators. It is the difference in
gain change between any two amplifiers with the contrast voltage, V21, at either 4V or 2V measured relative to an AV max condition V21 e 4V. For example, at AV
max, the three amplifier gains might be 17.4 dB, 16.9 dB and 16.4 dB and change to 7.3 dB, 6.9 dB and 6.5 dB respectively for V21 e 2V. This yields the measured
typical g 0.1 dB channel tracking.
Note 8: Brightness tracking error is measured with all three video channels set for equal gain. The measured value is limited by the resolution of the measurement
equipment.
Note 9: When measuring video amplifier bandwidth or pulse rise and fall times, a double sided full ground plane printed circuit board is recommended. Video
amplifier isolation tests also require this printed circuit board. The measured rise and fall times are effective rise and fall times, taking into account the rise and fall
times of the generator.
Note 10: Measure output levels of either undriven amplifier relative to the driven amplifier to determine channel isolation. Terminate the undriven amplifier inputs.
4
Typical Performance Characteristics
VCC e 12V, TA e 25§ C unless otherwise specified
Attenuation vs Contrast
Control Voltage ( f e 12 kHz)
Attenuation vs Drive
Control Voltage ( f e 12 kHz)
Back Porch Clamp Pulse
Width vs Pin 22 Voltage
Minimum External g H
Sync Input Level (VPP)
vs Input Duty Cycle (%)
Contrast vs Frequency
Drive Control vs Frequency
Crosstalk vs Frequency
TL/H/11238 – 2
5
6
FIGURE 1. LM1204 Test Circuit
TL/H/11238 – 3
Timing Diagram
TL/H/11238 – 4
Input/Output Stages
b H Sync Output Stage
Composite Video Input
TL/H/11238 – 6
TL/H/11238 – 5
Video Output Stage
TL/H/11238 – 21
7
Input/Output Stages (Continued)
g H/HV Sync Input
Video Input Stage
TL/H/11238–7
TL/H/11238 – 8
Pin Descriptions
VCC (Pins 2, 4, 6, 19,
31, 36, 41, 44)
Contrast Cap (Pins 1, 3)
R Clamp Cap (Pin 5)
B Clamp Cap (Pin 10)
G Clamp Cap (Pin 14)
R Video In (Pin 7)
B Video In (Pin 11)
G Video In (Pin 17)
R D Gain (Pin 9)
B D Gain (Pin 13)
G D Gain (Pin 15)
Compose Video Input
(Pin 18)
Brightness Control
(Pin 20)
Contrast Control
(Pin 21)
All VCC pins must be externally wired together. For stable operation, each supply pin should be
bypassed with a 0.01 mF and a 0.1 mF capacitor connected as close to the pin as is possible.
An external decoupling capacitor of value 0.1 mF should be connected between pins 1 and 3 for
contrast control.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
clamping of the red channel video signal to the reference black level.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
clamping of the blue channel video signal to the reference black level.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
clamping of the green channel video signal to the reference black level.
This is the input for the red channel video signal, the signal should be AC coupled to the input through
a 10 mF capacitor.
This is the input for the blue channel video signal, the signal should be AC coupled to the input
through a 10 mF capacitor.
This is the input for the green channel video signal, the signal should be AC coupled to the input
through a 10 mF capacitor.
This is the gain adjustment pin for the red video channel. A 0V to 4VDC voltage is applied to this pin to
vary the gain of the red channel. Usually, the red channel is set for maximum gain and the gains of the
blue and green channels are reduced relative to the red channel until white balance is achieved on
the CRT screen.
This is the gain adjustment pin for the blue video channel. A 0V to 4 VDC voltage is applied to this pin
to vary the gain of the blue channel.
This is the gain adjustment pin for the green video channel. A 0V to 4 VDC voltage is applied to this pin
to vary the gain of the green channel.
This is the sync separator input pin. For Sync on Green systems, the green channel video signal
should be AC coupled to pin 18 through a 0.1 mF capacitor.
If the LM1204 is used without blanking then this pin should be biased at 2.0 VDC. Brightness control
for all three video channels is now controlled by pin 43 (blank level adjust pin). See Figure 4 . If the
LM1204 is used with blanking then this pin allows the user to simultaneously DC offset the video
portion of the output signals of all three channels thus allowing brightness control (See Figure 5 ).
This pin simultaneously controls the gain of all three video channels. A 0V to 4 VDC input voltage is
applied to this pin, with 0V corresponding to minimum gain (i.e., maximum attenuation of video signal)
and 4V corresponding to maximum gain (i.e., minimum attenuation of the video signal).
8
Pin Descriptions (Continued)
Back Porch Clamp Width
Adjust (Pin 22)
The LM1204 provides DC restoration or clamping during the back porch interval of the video signal.
The width of LM1204’s internally generated back porch clamp signal can be varied by applying a 0V
to 4 VDC voltage to this pin. The back porch clamp signal width can be varied from approximately
0.3 ms to 4.0 ms by applying 4V to 0.5V respectively. By connecting the blank gate input pin (pin 24)
to VCC, the back porch clamp pulse can be monitored on the bH Sync output pin (pin 26). See
Figures 4 and 5 . By connecting pin 22 to VCC, the LM1204 functions as a non-gated amplifier
requiring no clamping. See Section 4 under application hints for further information.
g H Sync In (Pin 23)
This is the external sync input pin, it accepts a negative or positive polarity signal, either horizontal
sync or a composite sync (1.2 VPP minimum amplitude). The LM1204 also provides a negative
polarity (TTL compatible) horizontal sync or composite sync output on pin 26. If the composite video
input (pin 18) is not used then an H Sync signal should be AC coupled to this pin through a 0.1 mF
capacitor. The g H Sync input has priority over the composite video input if both signals are present.
This is the blank gate input pin. The LM1204 allows video blanking at the preamplifier. If blanking is
desired then a TTL compatible, negative polarity blanking signal should be applied to this pin. During
the blanking interval, all three video outputs are level shifted to the blank level set by the voltage at
pin 43. If blanking is not required then, pin 24 should be biased at 4V.
Connecting pin 24 to VCC will cause pin 26 to output the internally generated back porch clamp
signal. The user can observe the change in back porch width as the potential at pin 22 is varied (see
Figures 4 and 5 ).
A 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows the LM1204 to
integrate the g H Sync input signal and genreate the proper polarity switch for bH Sync output.
This output pin provides a negative polarity horizontal sync signal for other system uses. There is
approximately 100 ns delay between the g H Sync input signal at pin 23 and the bH Sync output
signal at pin 26.
Connecting pin 24 to VCC will cause pin 26 to output the internally generated back porch clamp
signal. The user can observe the change in back porch clamp pulse width as the potential at pin 22 is
varied (See Figures 4 and 5 ).
This is the cutoff adjustment input for the green video channel. The green video output signal from
pin 30 is fed back to this input through a potentiometer thus allowing the user to individually adjust
the cutoff (black reference) level for each gun. The signal level at this pin should be between 0.5V
and 4V.
This is the cutoff adjustment input for the blue video channel. The blue video output signal from pin
35 is fed back to this input through a potentiometer thus allowing the user to individually adjust the
cutoff (black reference) level for each gun. The signal level at this pin should be between 0.5V and
4V.
This is the cutoff adjustment input for the red video channel. The red video output signal from pin 40
is fed back to this input through a potentiometer thus allowing the user to individualy adjust the cutoff
(black reference) level for each gun. The signal level at this pin should be between 0.5V and 4V.
This is the green channel video output.
Blank Gate In (Pin 24)
Integrator Cap (Pin 25)
b H Sync Out (Pin 26)
G Feedback (Pin 28)
B Feedback (Pin 33)
R Feedback (Pin 38)
G Video Output
(Pin 30)
B Video Output
(Pin 35)
R Video Output
(Pin 40)
G Blank Clamp Cap
(Pin 32)
B Blank Clamp Cap
(Pin 37)
R Blank Clamp Cap
(Pin 42)
Blank Level Adjust
(Pin 43)
GND (Pins 8, 12 16, 27,
29, 34, 39)
This is the blue channel video output.
This is the red channel video output.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
blanking for the green video channel.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
blanking for the blue video channel.
A 0.022 mF to 0.1 mF capacitor should be connected from this pin to ground. This capacitor allows
blanking for the red video channel.
This pin serves two functions depending on whether the LM1204 is used with blanking or without
blanking. If blanking is not selected then pin 20 should be biased at 2.0 VDC and pin 43 assumes the
role of brightness control. Varying the potential at pin 43 will simultaneously DC offset the video
output signals of all three channels (See Figure 4 ). If the LM1204 is used with blanking then during
the blanking interval, all three video output signals will be level shifted to the blank level. The desired
blank level can be set by adjusting the potential at pin 43. Brightness control is now made possible
by varying the potential at pin 20. Adjusting the brightness control DC offsets the video portion of the
signal relative to the fixed blank level (all channels are affected simultaneously). See Figure 5 .
Ground. All ground pins must be connected to the ground plane.
9
ment for each channel is done by varying the feedback voltage at each of the R, G and B feedback inputs (Pins 38, 28
and 33). For example, cutoff adjustment for the green channel is done by potentiometer R8 shown in Figure 2 .
Adjusting the contrast control (potentiometer R3 in Figure
2 ) varies the peak to peak amplitude (includes sync tip if
present) of all three video output signals relative to their
black reference level. The D Gain adjust (pins 9, 15 and 13
for R, G, and B channels respectively) allows the user to
individually adjust the AC gain of each channel. For example
the AC gain of the green channel is adjusted using potentiometer R5 as shown in Figure 2 . Normally the red channel
is set for maximum gain and the gains of the blue and green
channels are reduced until white balance is achieved on the
CRT monitor’s screen. Figure 4 shows the adjustments for
operation without blanking.
Applications Hints
The LM1204 is a wideband video amplifier system designed
specifically for high resolution RGB CRT monitors. The device includes circuitry for DC restoration of video signals
and also allows contrast and brightness control. DC restoration is done during the back porch interval of the video signal. An internal sync separator generates a back porch
clamp signal either from a ‘‘Sync on Green’’ signal applied
to the composite video input (pin 18) or from an externally
supplied g H Sync signal . The LM1204 first looks at the
g H Sync input (pin 23), if an external horizontal sync signal
is not present then the device syncs off the composite video
input. The internally generated back porch clamp pulse
width is user adjustable.
A blanking function is also included. This allows the user to
cutoff the beam current in the CRT’s guns during the blanking interval thereby preventing horizontal retrace lines from
being visible. Normally blanking is done by applying a high
voltage pulse at the grid. However, blanking at the cathode
using the LM1204 leads to ease of design and lowered cost.
2.0 Operation with Blanking
Much of what was discussed in Section 1.0 also applies
when the LM1204 is used with the blanking function. However, there are notable differences as described herein. For
operation with blanking, a TTL compatible blanking signal
must be applied to the blank gate input (pin 24).
Figure 2 shows the block diagram of the green video channel and the control logic. The two modes of operation, with
and without blanking, are described below in detail.
During the blanking period, the blanking comparator connects switch S2 to position X (See Figure 2 ). This causes
the LM1204 to level shift the video output signal to the blank
level. Adjusting R9 will adjust the blank level of all three
channels. Individual blank level adjustment for each channel is done by varying the feedback voltage at each of the
R, G and B feedback inputs (pin 38, 28 and 33). In Figure 2
this is done by adjusting potentiometer R8 for the green
channel.
During the video portion of the video signal, S2 is connected
to position Y. Brightness control is now accomplished by
varying the potential at the brightness control pin (pin 20).
Adjusting R6 offsets the video portion of all three output
signals relative to the fixed blank level, restoring the DC
level of the video signal. Figure 5 shows the adjustments for
operation with blanking.
1.0 Operation without Blanking
For operation without blanking, the blank gate input (pin 24)
should be connected to a 4V. This causes the blank comparator to connect switch S2 to position Y (See Figure 2 ).
Furthermore, the brightness control input pin (pin 20) should
be biased at a potential between 1V (Min) and 3.8V (Max), it
is best to bias this pin at 2V. The video signal is AC coupled
to the input of the LM1204 as shown for the green channel
in Figure 2 . During the back porch interval of the video signal (See Figure 3 ), the internally generated back porch
clamping pulse goes low, causing switches S1A and S1B to
be closed. The closure of S1A causes gm1 to charge capacitor C2 to a potential determined by the DC voltage at pin
20. This allows gm1 to set up an average DC bias for the AC
coupled video signal at the input of A1. When the back
porch clamping pulse is high, S1A and S1B are opened.
With S1A open, gm1 is effectively disconnected from C2, C2
now holds the DC bias voltage. The transconductance
stage gm1 therefore functions as a sample and hold device
and holds the input of A1 at the desired DC bias.
The LM1204 uses black level clamping at the back porch of
the video signal to accomplish DC restoration. The transconductance stage gm2 is enabled during the back porch
clamp period to provide a sample and hold function. During
the back porch clamp period, DC feedback from LM1204’s
video output is compared with the voltage set by potentiometer R9. Depending on A2’s output voltage, C6 is either
charged or discharged so that the feedback loop consisting
of gm2 and A2 is stabilized and the output is clamped to the
black level. All this occurs during the back porch clamp period. During the video portion of the signal, gm2 is disabled
and C6 holds the fixed black level reference voltage. The
beginning of each new line on the raster always starts from
a fixed reference black level thus restoring the DC component of each line.
A2 is a summing amplifier that adds a DC offset component
from gm2 to the video signal from the multiplier. Adjusting
R9 will DC offset the output signals of all three channels
thus providing brightness control. Individual cutoff adjust-
3.0 Stability Considerations
For optimum performance and stable operation, a double
sided PC board with adequate ground plane is essential.
Moreover, soldering the LM1204 on to the PC board will
yield best results. Each supply pin (pins 2, 4, 6, 19, 31, 36,
41 and 44) should be bypassed with a 0.01 mF and a 0.1 mF
capacitor connected as close to the supply pin as is possible.
When driving the LM1204 from a 75X video source, the
cable is terminated with 75X to minimize reflections caused
by transmission line effects. However, the input impedance
of LM1204 is capacitive and is also affected by the stray
capacitance of the PC board. Thus the input impedance is a
function of frequency. This changes the impedance of the
cable termination. This can introduce overshoot and ringing
in LM1204’s pulse response. A 100X resistor in series with
the blocking capacitor at the video input will minimize overshoot and ringing (see Figure 8 ). The value of the resistor is
empirically determined. 100X is a good starting value.
Since the LM1204 is a wide bandwidth amplifier with high
gain at high frequencies, the device may oscillate when driving a large capacitive/inductive load. To prevent oscillation,
the amplifier’s gain is rolled off at high frequencies. This is
accomplished by an RC network comprised of a resistor in
10
3.0 Stability Considerations (Continued)
Non-Gated High
Frequency Application
series with a capacitor connected from the video output pin
to ground (see Test Circuit, Figure 1 ). A 110X to 200X
resistor in series with 10 pF is quite adequate for most applications. However, if oscillations don’t cease then the value
of the resistor should be decreased or the value of the capacitor should be increased or a combination of the two.
By connecting the back porch width adjust pin (pin 22) to
VCC, the LM1204 functions as a non-gated amplifier requiring no sync or blanking signals. Figure 9 shows a triple high
frequency amplifier with variable gain and DC offset control.
In this mode of operation, filtered DC feedback must be
provided to pins 28, 33 and 38 as shown in Figure 9 .
LM1204
TL/H/11238 – 9
FIGURE 2. Block Diagram Showing Timing Circuitry and Green Video Channel
TL/H/11238 – 10
FIGURE 3. Composite Video and Timing Signals
11
TL/H/11238 – 11
TL/H/11238–12
TL/H/11238 – 13
TL/H/11238 – 14
FIGURE 4. LM1204 Adjustments without Blanking
12
TL/H/11238 – 15
FIGURE 5. LM1204 Adjustments with Blanking
13
14
FIGURE 6. The LM1204 driving cascode CRT video amplifiers and operating without blanking. Brightness control is accomplished by potentiometer R12 (See Figure 4
for explanation of adjustments). Each VCC pin should be bypassed with a 0.01 mF and a 0.1 mF capacitor connected as close to the pin as is possible.
TL/H/11238 – 16
Typical Applications Circuits
15
FIGURE 7. The LM1204 driving cascode CRT video amplifiers and operating with blanking. The video signal is level shifted to the user adjustable blank level
during the blanking period. Brightness control DC offsets the video signal relative to the fixed blank level and is accomplished by potentiometer R7. See Figure 5
for explanation of adjustments. Each VCC pin should be bypassed with a 0.01 mF and a 0.1 mF capacitor connected as close to the pin as is possible.
TL/H/11238 – 17
Typical Applications Circuits (Continued)
Typical Applications Circuits (Continued)
TL/H/11238 – 18
FIGURE 8. Complete circuitry for an RGB CRT video board using the LM1204 and LH2426AS.
The video output signals from LH2426AS are AC coupled and diode clamped to greater than 80V.
16
Typical Applications Circuits (Continued)
TL/H/11238 – 20
FIGURE 8. (Continued)
17
FIGURE 9. Three channel high frequency amplifier with gain and DC offset control (non-video application). Each VCC pin should be
bypassed with a 0.01 mF and a 0.1 mF capacitor connected as close to the pin as is possible.
TL/H/11238 – 19
Typical Applications Circuits (Continued)
18
19
LM1204 150 MHz RGB Video Amplifier System
Physical Dimensions inches (millimeters)
Order Number LM1204V
NS Package Number V44A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.