Order this document by LM2935/D The LM2935 is a dual positive 5.0 V low dropout voltage regulator, designed for standby power systems. The main output is capable of supplying 750 mA for microprocessor power, and can be turned “on” and “off” by the switch/reset input. The other output is dedicated for standby operation of volatile memory, and is capable of supplying up to 10 mA loads. The total device features a low quiescent current of 3.0 mA or less when supplying 10 mA from the standby output. This part was designed for harsh automotive environments and is therefore immune to many input supply voltage problems such as reverse battery (–12 V), double battery (+24 V), and load dump transients (+60 V). • Two Regulated 5.0 V Outputs • • • • • • • • • • Main Output Current in Excess of 750 mA LOW DROPOUT DUAL VOLTAGE REGULATOR SEMICONDUCTOR TECHNICAL DATA TH SUFFIX PLASTIC PACKAGE CASE 314A On/Off Control of Main Output Standby Output Current in Excess of 10 mA Low Input/Output Differential of Less than 0.6 V at 500 mA 1 Short Circuit Current Limiting 5 Internal Thermal Shutdown Low Voltage Indicator Output Designed for Automotive Environment Including • Reverse Battery Protection • Double Battery Protection • Load Dump Protection • Reverse Transient Protection Economical 5–Lead TO–220 Package with Two Optional Leadforms Also Available in Surface Mount D2PAK Package TV SUFFIX PLASTIC PACKAGE CASE 314B 1 5 Heatsink surface connected to Pin 3. T SUFFIX PLASTIC PACKAGE CASE 314D 1 5 Pin 1. Input Voltage/VCC 2. Main Output 3. Ground 4. Switch/Reset 5. Standby/Output ORDERING INFORMATION Device Operating Temperature Range LM2935D2T LM2935T LM2935TH Package Surface Mount 40° to +125°C 125°C TJ = –40° LM2935TV Plastic Power D2T SUFFIX PLASTIC PACKAGE CASE 936A (D2PAK) Horizontal Mount Vertical Mount 1 5 Heatsink surface (shown as terminal 6 in case outline drawing) is connected to Pin 3. Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA Rev 1 1 LM2935 Typical Application Circuit Main Output Input Vin 5.0 V/750 mA 2 1 + 0.1 S1* *The main output is “Off” with switch S1 open. 10 LM2935 20 k Standby Switch/ Reset 4 5.0 V/10 mA 5 + 3 10 Gnd An input bypass capacitor is recommended if the regulator is located more than 4″ from the supply input filter. The LM2935 is not internally compensated and thus requires an external output capacitor for stability. A minimum capacitance of 10 µF is recommended. The actual capacitance value is dependent upon load current, temperature, and the capacitor’s equivalent series resistance (ESR). The least stable condition is encountered at maximum load current and minimum ambient temperature. This device contains 29 active transistors. MAXIMUM RATINGS Rating Symbol Value Unit VI 60 Vdc –VI(τ) – 50 Vpk Iin 5.0 mA PD RθJA RθJC Internally Limited 65 5.0 W °C/W °C/W PD RθJA RθJC Internally Limited Per Figure 1 5.0 W °C/W °C/W TJ – 40 to +150 °C Tstg – 65 to +150 °C Input Voltage Continuous Transient Reverse Polarity Input Voltage 1.0% Duty Cycle, τ ≤ 100 ms Switch/Reset Input Current Power Dissipation Case 314A, 314B and 314D (TO–220 Type) TA = 25°C Thermal Resistance, Junction–to–Ambient Thermal Resistance, Junction–to–Case Case 936A (D2PAK) TA = 25°C Thermal Resistance, Junction–to–Ambient Thermal Resistance, Junction–to–Case Operating Junction Temperature Range Storage Temperature Range ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, Istby = 0 mA, CO = 10 µF, Cstby = 10 µF, TJ = 25°C [Note 1].) Characteristic Symbol Min Typ Max Unit Output Voltage (Vin = 6.0 V to 26 V, IO = 5.0 mA to 500 mA, TJ = – 40 to +125°C) VO 4.75 5.0 5.25 V – – 4.0 10 25 50 – 10 50 MAIN OUTPUT Line Regulation Vin = 9.0 V to 16 V, IO = 5.0 mA Vin = 6.0 V to 26 V, IO = 5.0 mA Regline Load Regulation (IO = 5.0 mA to 500 mA) Regload Output Impedance IO = 500 mAdc and 10 mArms, f = 100 Hz to 10 kHz ZO Output Noise Voltage (f = 10 Hz to 100 kHz) Long Term Stability 2 mV mV mΩ – 200 – Vn – 100 – µVrms S – 20 – mV/kHR MOTOROLA ANALOG IC DEVICE DATA LM2935 ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 500 mA, Istby = 0 mA, CO = 10 µF, Cstby = 10 µF, TJ = 25°C [Note 1].) Characteristic Symbol Min Typ Max Unit RR – 66 – dB – – 0.45 0.82 0.6 – MAIN OUTPUT (continued) Ripple Rejection (f = 120 Hz) Dropout Voltage IO = 500 mA IO = 750 mA VI–VO Short Circuit Current Limit V ISC 0.75 1.2 – A Vth(OV) 26 31 – V Output Sink Current (VOL = 1.2 V) ISink – 5.0 – mA Output Voltage (Ron/off = 20 kΩ) Low State, Vin = 4.0 V High State, Vin = 14 V VOL VOH – 4.5 0.9 5.0 1.2 6.0 Ron/off – 20 30 kΩ –VO – 0.6 0 – V Over–Voltage Shutdown Threshold SWITCH/RESET Output Pull–Up Resistor, “On”/“Off” (Note 2) Output Voltage with Reverse Polarity Input (Vin = –15 V, RL = 10 Ω) V ELECTRICAL CHARACTERISTICS (Vin = 14 V, IO = 0 mA, Istby = 10 mA, CO = 10 µF, Cstby = 10 µF, TJ = 25°C [Note 1].) Characteristic Symbol Min Typ Max Unit Output Voltage (Vin = 6.0 V to 26 V, Istby = 1.0 mA to 10 mA, TJ = –40 to +125°C) VO(stby) 4.75 5.0 5.25 V VO–VO(stby) – 200 0 200 mV Line Regulation (Vin = 6.0 V to 26 V) Regline – 4.0 50 mV Load Regulation (Istby = 1.0 mA to 10 mA) Regload – 10 50 mV Output Impedance I(stby) = 10 mAdc and 1.0 mArms, f = 100 Hz to 10 kHz ZO(stby) – 1.0 – STANDBY OUTPUT Tracking Voltage Ω Output Noise Voltage (f = 10 Hz to 100 kHz) Vn – 300 – µVrms Long Term Stability S – 20 – mV/kHR RR – 66 – dB Ripple Rejection (f = 120 Hz) Dropout Voltage (Istby = 10 mA) VI–VO(stby) – 0.55 0.7 V Short Circuit Current Limit ISC 25 70 – mA Output Voltage with Reverse Polarity Input Vin = –15 V, RL = 510 Ω –VO – 0.3 0 – – 5.0 6.0 – – – – 3.0 40 90 2.0 – 100 – 3.0 Output Voltage with Maximum Positive Input Vin = 60 V, RL = 510 Ω V VO(max) V TOTAL DEVICE Bias Current IO = 10 mA, Istby = 0 mA IO = 500 mA, Istby = 0 mA IO = 750 mA, Istby = 0 mA Main Output “Off”, Istby = 10 mA IB mA NOTES: 1. Low duty cycle pulse techniques are used during test to maintain junction temperature as close to ambient as possible. 2. The maximum switch/reset current must not exceed 5.0 mA. MOTOROLA ANALOG IC DEVICE DATA 3 LM2935 TYPICAL CIRCUIT WAVEFORMS 60 V S1, “On”/“Off” Switch 26 V 14 V Vin, Input Voltage (Pin 1) 14 V 14 V 3.0 V 9.0 V Open Closed 5.0 V Open 5.0 V 5.0 V 2.4 V VO, Main Output Voltage (Pin 2) 5.0 V 5.0 V 0V 5.0 V 0V Reset (Pin 4) Vstby, Standby Voltage (Pin 5) 5.0 V 5.0 V 2.4 V Main Output Turn “On” Low Input Voltage Main Output Short Circuit Input Voltage Line Noise Load Dump Main Output Turn “Off” Thermal Shutdown JUNCTION–TO–AIR ( °C/W) R θ JA, THERMAL RESISTANCE 80 3.5 PD(max) for TA = 50°C 70 3.0 Free Air Mounted Vertically 60 ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ 2.0 oz. Copper L Minimum Size Pad 50 L 40 RθJA 30 2.5 2.0 1.5 PD, MAXIMUM POWER DISSIPATION (W) Figure 1. D2PAK Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length 1.0 0 5.0 10 15 20 25 30 L, LENGTH OF COPPER (mm) 4 MOTOROLA ANALOG IC DEVICE DATA LM2935 OUTLINE DIMENSIONS TH SUFFIX PLASTIC PACKAGE CASE 314A–03 ISSUE D –T– –P– B NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION D DOES NOT INCLUDE INTERCONNECT BAR (DAMBAR) PROTRUSION. DIMENSION D INCLUDING PROTRUSION SHALL NOT EXCEED 0.043 (1.092) MAXIMUM. SEATING PLANE C Q E OPTIONAL CHAMFER A U F L K 1 2 3 4 5 G J 5 PL S D 5 PL 0.014 (0.356) M T P M DIM A B C D E F G J K L Q S U INCHES MIN MAX 0.572 0.613 0.390 0.415 0.170 0.180 0.025 0.038 0.048 0.055 0.570 0.585 0.067 BSC 0.015 0.025 0.730 0.745 0.320 0.365 0.140 0.153 0.210 0.260 0.468 0.505 MILLIMETERS MIN MAX 14.529 15.570 9.906 10.541 4.318 4.572 0.635 0.965 1.219 1.397 14.478 14.859 1.702 BSC 0.381 0.635 18.542 18.923 8.128 9.271 3.556 3.886 5.334 6.604 11.888 12.827 TV SUFFIX PLASTIC PACKAGE CASE 314B–05 ISSUE J Q OPTIONAL CHAMFER F E A U K NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION D DOES NOT INCLUDE INTERCONNECT BAR (DAMBAR) PROTRUSION. DIMENSION D INCLUDING PROTRUSION SHALL NOT EXCEED 0.043 (1.092) MAXIMUM. C B –P– S L W V 1 2 3 4 5 G 0.24 (0.610) J 5 PL M T H D 5 PL 0.10 (0.254) M T P M N –T– MOTOROLA ANALOG IC DEVICE DATA SEATING PLANE DIM A B C D E F G H J K L N Q S U V W INCHES MIN MAX 0.572 0.613 0.390 0.415 0.170 0.180 0.025 0.038 0.048 0.055 0.850 0.935 0.067 BSC 0.166 BSC 0.015 0.025 0.900 1.100 0.320 0.365 0.320 BSC 0.140 0.153 0.620 – 0.468 0.505 0.735 – 0.090 0.110 MILLIMETERS MIN MAX 14.529 15.570 9.906 10.541 4.318 4.572 0.635 0.965 1.219 1.397 21.590 23.749 1.702 BSC 4.216 BSC 0.381 0.635 22.860 27.940 8.128 9.271 8.128 BSC 3.556 3.886 – 15.748 11.888 12.827 – 18.669 2.286 2.794 5 LM2935 OUTLINE DIMENSIONS T SUFFIX PLASTIC PACKAGE CASE 314D–03 ISSUE D SEATING PLANE –T– NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION D DOES NOT INCLUDE INTERCONNECT BAR (DAMBAR) PROTRUSION. DIMENSION D INCLUDING PROTRUSION SHALL NOT EXCEED 10.92 (0.043) MAXIMUM. C –Q– B E U A DIM A B C D E G H J K L Q U S L 1 2 3 4 5 K S J H G D 5 PL 0.356 (0.014) T Q M INCHES MIN MAX 0.572 0.613 0.390 0.415 0.170 0.180 0.025 0.038 0.048 0.055 0.067 BSC 0.087 0.112 0.015 0.025 1.020 1.065 0.320 0.365 0.140 0.153 0.105 0.117 0.543 0.582 MILLIMETERS MIN MAX 14.529 15.570 9.906 10.541 4.572 4.318 0.965 0.635 1.397 1.219 1.702 BSC 2.845 2.210 0.635 0.381 25.908 27.051 9.271 8.128 3.886 3.556 2.972 2.667 13.792 14.783 M D2T SUFFIX PLASTIC PACKAGE CASE 936A–02 (D2PAK) ISSUE A OPTIONAL CHAMFER A TERMINAL 6 –T– U E S K V B H 1 2 3 4 5 M L P N D 0.010 (0.254) M R T G C 6 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: INCH. 3 TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4 DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 6. 5 DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. DIM A B C D E G H K L M N P R S U V INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.067 BSC 0.539 0.579 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.702 BSC 13.691 14.707 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN MOTOROLA ANALOG IC DEVICE DATA LM2935 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA ANALOG IC DEVICE DATA 7 LM2935 How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 8 ◊ *LM2935/D* LM2935/D MOTOROLA ANALOG IC DEVICE DATA