LMS5213 80mA, µCap, Low Dropout Voltage Regulator in SC70 General Description Features • The LMS5213 is a µCap, low dropout voltage regulator with very low quiescent current, 220µA typical, at 80mA load. It also has very low dropout voltage, typically 20mV at light load and 330mV at 80mA. The LMS5213 provides up to 80mA and consumes a typical of 1µA in disable mode. The LMS5213 is optimized to work with low value, low cost ceramic capacitors. The output typically require only 0.47µF of output capacitance for stability. The enable pin can be tied to VIN for easy device layout. The LMS5213 is designed for portable, battery powered equipment applications with small space requirements. The LMS5213 is available in a space saving 5-pin SC70 package. Performance is specified for the −40˚C to +125˚C temperature range and is available in 2.8V, 3.0V and 3.3V fixed voltages. For other output voltage options, please contact National Semiconductor. n n n n n n n n n n Space saving SC70 package Available in 2.8V, 3.0V, and 3.3V fixed voltages Guaranteed 80mA output Low quiescent current Low dropout voltage Low temperature coefficient Current and thermal limiting Logic-controlled shutdown Stability with low-ESR ceramic capacitors Pin-to-pin replacement for Mic™ 5213 Applications n n n n n Cellular Phones Battery-powered equipment Bar code scanner Laptop/palmtop computer High-efficiency linear power supplies Typical Application 20010919 © 2004 National Semiconductor Corporation DS200109 www.national.com LMS5213 80mA, µCap, Low Dropout Voltage Regulator in SC70 January 2004 LMS5213 Simplified Schematic 20010911 Pin Description Pin Number Pin Name 1 VEN Enable Input Logic, Logic High = Enabled Logic Low = Shutdown 2 NC Not internally connected www.national.com Pin Function 3 GND Ground 4 VOUT Output Voltage 5 VIN Input Voltage 2 LMS5213 Connection Diagram SC70-5 20010921 Top View Ordering Information Package Part Number Package Marking LMS5213IM7-2.8 5-Pin SC70 L0E LMS5213IM7X-2.8 LMS5213IM7-3.0 L1E LMS5213IM7X-3.0 LMS5213IM7-3.3 L2E LMS5213IM7X-3.3 3 Transport Media NSC Drawing 1k Units Tape and Reel 3k Units Tape and Reel MAA05A 1k Units Tape and Reel 3k Units Tape and Reel 1k Units Tape and Reel 3k Units Tape and Reel www.national.com LMS5213 Absolute Maximum Ratings (Note 1) Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltages VIN ESD Tolerance (Note 2) Human Body Model 2000V Junction Temperature 150˚C VIN, VOUT, VEN Storage Temperature Range −40˚C to +125˚C −65˚C to 150˚C Package Thermal Resistance −0.3 TO 6.5V Infrared or Convection (20 sec) 0V to VIN Junction Temp. Range (Note 3) SC70-5 Soldering Information Wave Soldering (10 sec) 2.7V to 6V VEN 478˚C/W 235˚C 260˚C (lead temp) Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C, VIN = VOUT + 1V, IL = 1mA, CL = 0.47µF, VEN ≥ 2.0V. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions Min (Note 5) Typ (Note 4) Max (Note 5) Units 3 4 % 50 200 ppm/˚C VO Output Voltage Accuracy -3 -4 ∆VO/∆T Output Voltage Temp. Coefficient (Note 10) ∆VO/VO Line Regulation VIN = VOUT +1V to 6V 0.008 0.3 0.5 % ∆VO/VO Load Regulation IL = 0.1mA to 80mA (Note 6) 0.08 0.3 0.5 % VIN-VO Dropout Voltage (Note 7) IL = 100µA 20 IL = 20mA 70 IL = 50mA 180 IL = 80mA 330 600 1 10 IQ Quiescent Current VEN ≤ 0.4V (Shutdown) IGND Ground Pin Current IL = 100µA, VEN ≥ 2.0V (active) 160 350 IL = 20mA, VEN ≥ 2.0V (active) 180 IL = 50mA, VEN ≥ 2.0V (active) 200 IL = 80mA, VEN ≥ 2.0V (active) 220 3000 VIN = VOUT(NOMINAL) –0.5V 200 300 250 IGNDDO Ground Pin Current at Dropout, (Note 8) ILIMIT Current Limit VOUT = 0V 180 ∆VO/∆PD Thermal Regulation (Note 9) 0.05 750 mV µA µA µA mA %W Enable Input VIL Enable Input Voltage Level VIH IIL Logic Low (off) Logic High (on) Enable Input Current IIH 0.6 V 2.0 V VIL ≤ 0.6V 0.01 1 µA VIH ≥ 2.0V 15 50 µA Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human body model, 1.5kΩ in series with 100pF. Note 3: The maximum power dissipation is a function of TJ(max) , θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Note 4: Typical Values represent the most likely parametric norm. Note 5: All limits are guaranteed by testing or statistical analysis. Note 6: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. Note 8: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. www.national.com 4 (Continued) Note 9: Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for an 80mA load pulse at VIN = 6V for t = 16ms. Note 10: Output voltage temperature coefficient is defined as the worst-case voltage change divided by the total temperature range. Typical Characteristics Unless otherwise specified, TA = 25˚C, VOUT = 2.8V, CL = 0.47µF Dropout Voltage vs. Output Current Dropout Voltage vs. Temperature 20010912 20010901 Dropout Characteristics Dropout Characteristics 20010906 20010907 5 www.national.com LMS5213 Electrical Characteristics LMS5213 Typical Characteristics Unless otherwise specified, TA = 25˚C, VOUT = 2.8V, CL = 0.47µF Ground Current vs. Output Current (Continued) Ground Current vs. Supply Voltage 20010904 20010903 Ground Current vs. Temperature Short Circuit Current vs. Input Voltage 20010905 20010913 Output Voltage vs. Temperature Load Transient 20010914 20010902 www.national.com 6 Load Transient (Continued) Line Transient 20010917 20010916 Line Transient Ripple Voltage vs. Frequency 20010918 20010908 Ripple Voltage vs. Frequency Noise Characteristics 20010910 20010909 7 www.national.com LMS5213 Typical Characteristics Unless otherwise specified, TA = 25˚C, VOUT = 2.8V, CL = 0.47µF LMS5213 Typical Characteristics Unless otherwise specified, TA = 25˚C, VOUT = 2.8V, CL = 0.47µF Enable Characteristics (VO = 3.3V) Enable Characteristics (VO = 3.3V) 20010924 20010923 No-Load Stability The LMS5213 will remain stable and in regulation with noload (other than the internal voltage divider). This is especially important in CMOS RAM keep-alive applications. Enable Input The LMS5213 is shut off by pulling the VEN pin below 0.6V; all internal circuitry is powered off and the quiescent current is typically 1µA. Pulling the VEN high above 2V re-enables the device and allows operation. If the shut down feature is not used, the VEN pin should be tied to VIN to keep the regulator output on all the time. Application Information The LMS5213 is a low dropout, linear regulator designed primarily for battery-powered applications. The LMS5213 can be used with low cost ceramic capacitors, typical value of 0.47µF. As illustrated in the simplified schematics, the LMS5213 consists of a 1.25V reference, error amplifier, P-channel pass transistor and internal feedback voltage divider. The 1.25V reference is connected to the input of the error amp. The error amp compares this reference with the feedback voltage. If the feedback voltage is lower than the reference, the pass transistor gate is pulled lower allowing more current to pass and increasing the output voltage. If the feedback voltage is too high, the pass transistor gate is pulled up allowing less current to pass to the output. The output voltage is fedback through the resistor divider. Additional blocks include short circuit current protection and thermal protection. The LMS5213 features an 80mA P-channel MOSFET transistor. This provides several advantages over similar designs using PNP pass transistors including longer battery life. The P-channel MOSFET requires no base drive, which reduces quiescent current considerably. PNP based regulators waste considerable amounts of current in dropout when the pass transistor saturates. They also have high base drive currents under large loads. The LMS5213 does not suffer from these problems and consumes only the specified quiescent current under light and heavy loads. External Capacitors Like any low-dropout regulators, the LMS5213 requires external capacitors for regulator stability. The LMS5213 is specially designed for portable applications requiring minimum board space and the smallest components. A 0.1µF capacitor should be placed from VIN to GND if there is more than 10 inches of wire between the input and AC filter or when a battery is used as the input. This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean analog ground. The LMS5213 is designed to work with small ceramic output capacitors. Ceramic capacitors ranging between 0.47µF to 4.7µF are the smallest and least expensive. www.national.com (Continued) Thermal Behavior The LMS5213 regulator has internal thermal shutdown to protect the device from over heating. Under all operating conditions, the maximum junction temperature of the LMS5213 must be below 125˚C. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. The maximum power dissipation is PD(MAX) = (TJ(MAX) - TA)/θJA θJA is the junction-to-ambient thermal resistance, 478˚C/W for the LMS5213 in the SC70 package. TA is the maximum ambient temperature TJ(MAX) is the maximum junction temperature of the die, 125˚C When operating the LMS5213 at room temperature, the maximum power dissipation is 209 mW. The actual power dissipated by the regulator is PD = (VIN-VOUT) IL + VIN IGND The figure below shows the voltage and currents, which are present in the circuit. 8 The LMS5213 offers a smaller system solution that is ideal for general-purpose voltage regulation in any handheld device. (Continued) 20010922 FIGURE 1. Power Dissipation Diagram Substituting PD(MAX), determined above, for PD and solving for the operating condition that are critical to the application will give the maximum operating conditions for the regulator circuit. To prevent the device from entering thermal shutdown, maximum power dissipation cannot be exceeded. Fixed Voltage Regulator 20010920 FIGURE 2. Single-Cell Regulator 9 www.national.com LMS5213 Application Information LMS5213 80mA, µCap, Low Dropout Voltage Regulator in SC70 Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SC70-5 NSC Package Number MAA05A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.