LSI/CSI UL ® LS7541 LSI Computer Systems, Inc. 1235 Walt Whitman Road, Melville, NY 11747 (631) 271-0400 FAX (631) 271-0405 A3800 TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) FEATURES: APPLICATIONS: PIN ASSIGNMENT TOP VIEW CLOCK 1 SYNC 2 V DD (+V ) 3 TOUCH 4 • Screw-in and built-in adapter modules for converting table and floor lamps to touch control for step dimming. • On-Off touch control of under-cabinet fluorescent lamps. 8 LS7541 Touch Sensitivity guaranteed to 600pF Touch Plate Capacitance. Touch Operation independent of line plug polarity. Pin selection of three available Brightness Step Sequences. Minimal external components. AGC Loop stabilizes immediately after Power-Up. Brightness state is Off after AC power applied. Brightness state is unchanged if AC power interrupted for < 0.5 sec. Advanced CMOS design for reliable operating characteristics and low power. 50/60 Hz Line Frequency. 5V Operation (VDD - VSS). LS7541 (DIP); LS7541-S (SOIC) - See Figure 1 - LSI • • • • • • • • • • • May 2006 TRIG 7 V SS (-V ) 6 MODE 5 CONTROL FIGURE 1 DESCRIPTION: The LS7541 is a CMOS integrated circuit which provides trigger pulses for triac phase control of incandescent lamps. The circuits are designed to operate with a wide variety of lamp sizes ranging from small table lamps to large floor lamps. The AGC Loop automatically adjusts Touch Sensitivity to be independent of lamp size. There are 3 different Brightness Step Sequences for each version of the IC which can be selected by the Three-State MODE pin as shown in Table 1. TABLE 1. BRIGHTNESS STEP MODES MODE PIN BRIGHTNESS STEP SEQUENCE FLOAT OFF-NIGHT LIGHT-MEDIUM-MAXIMUM-OFF VDD OFF-NIGHT LIGHT- LOW MEDIUM-HIGH MEDIUM-MAXIMUM-OFF Vss OFF-MAXIMUM-OFF The lamp brightness is made to vary by changing the delay of the TRIG pulse to the triac from the zero-crossing of the SYNC input. The delays are shown in Table 2 for 50Hz and 60Hz operation along with Delivered Power as a percentage of Full Power. Figure 2 illustrates the delay. TABLE 2. BRIGHTNESS POWER LEVELS Brightness Night Light Low Medium Medium High Medium Maximum 60Hz Delay (1) 6.0 ms 4.8 ms 4.0 ms 3.2 ms 0.85 ms 50Hz Delay (2) 7.2 ms 5.7 ms 4.8 ms 3.8 ms 1.0 ms % PWR (3) 12 35 53 72 99 (2) With 470kΩ connected between Pin 1 and VDD. (1) With 400kΩ connected between Pin 1 and VDD. (3) Percentage of Full Power delivered to a resistive load by the Triac Switch. 7541-051106-1 FIGURE 2. OUTPUT DELAY (Td) SYNC (Pin 2) TRIG(Pin 8) Td Td INPUT/OUTPUT DESCRIPTION: CLOCK Input (Pin 1) An external resistor connected between this input and VDD, along with an internal capacitor and oscillator stage, generates a clock which is used for all timing functions. The recommended value of this resistor for 50Hz and 60Hz operation is specified in the ELECTRICAL CHARACTERISTICS. The resistor value determines the Brightness Levels produced. (See Table 2) CONTROL I/O (Pin 5) An external R-C network connected between this pin and VDD establishes the controlling feedback for the AGC Loop. SYNC Input (Pin 2) 50 or 60Hz AC input for zero crossing detection. VSS (Pin 7) Supply voltage negative terminal. VDD (Pin 3) Supply voltage positive terminal. TRIG (Pin 8) The TRIG output produces a negative going pulse every half-cycle of the SYNC input to trigger the triac. The delay, Td, of the pulse with respect to the SYNC signal determines the Brightness Level produced. (See Table 2 & Figure 2) TOUCH Input (Pin 4) Input for sensing that a touch has been made on a lamp surface or other touch plate. MODE Input (Pin 6) A three-state input used to select the desired Brightness Step Sequence (See Table 1). ABSOLUTE MAXIMUM RATINGS: PARAMETER SYMBOL VALUE UNIT DC supply voltage Any input voltage Operating temperature Storage temperature VDD - VSS VIN TA TSTG +7 VSS - 0.5 to VDD + 0.5 -20 to +85 -65 to +150 V V °C °C The information included herein is believed to be accurate and reliable. However, LSI Computer Systems, Inc. assumes no responsibilities for inaccuracies, nor for any infringements of patent rights of others which may result from its use. 7541-072805-2 ELECTRICAL CHARACTERISTICS: ( All voltages referenced to Vss. TA = +25˚C unless otherwise specified.) PARAMETER Supply Voltage Supply Current SYMBOL VDD IDD MIN +4.5 - TYP - MAX +5.5 1.0 UNIT V mA TRIG Sink Current Vo = VDD - 3V IO -50 - - mA VDD = +5.0V TRIG Source Current Vo = VDD - 0.2V IO +0.1 - - mA VDD = +5.0V TRIG Pulse Width TW - - 100 115 - µs µs RC = 400kΩ, 60Hz RC = 470kΩ, 50Hz TRIG Pulse Delay (Medium Brightness) Td - 4.0 4.8 - ms ms Rc = 400kΩ, 60Hz Rc = 470kΩ, 50Hz CLOCK Resistor RC - - 400 470 - kΩ kΩ 60Hz 50Hz - - 10 1 - MΩ µF - CL - - 600 pF - CONTROL Resistor Capacitor Touch Plate Capacitance MODE 6 SYNC 2 ZERO-CROSS DETECTOR CLOCK 1 OSCILLATOR TOUCH 4 AGC CIRCUIT COUNTER DECODER STEPPER 5 CONTROL 7541-072805-3 CONDITIONS Output off, VDD = +5.0V V DD 3 +V V SS 7 -V FIGURE 3 LS7541 BLOCK DIAGRAM OUTPUT DRIVER 8 TRIG FIGURE 4. TOUCH LAMP APPLICATION SCHEMATIC +V R1 LOAD D1 MT2 + C1 AC MAINS - Z1 T1 R5 MT1 + C6 G - R6 -V SEE NOTE 1 C5 C2 8 7 TRIG V SS 6 5 MODE CONT C7* (SEE NOTE 2) LS7541 CLOCK SYNC V DD 2 1 R2 TOUCH 4 3 D2 R4 D3 R3 TOUCH PLATE (LAMP BODY) C3 115VAC APPLICATION R1 = 20kΩ, 1W C4 = 1000pF, 1kV R2 = 470kΩ, 1/4W C5 = 0.03µF, 10V R3 = 1kΩ, 1/4W C6 = 1µF, 10V (1) R4 = 400kΩ, 1/4W, 1% Z1 = 5.1V, 1/4W Zener R5 = 10MΩ, 1/4W D1 = 1N4004 R6 = 100Ω, 1/4W D2 = 1N4148 C1 = 47µF, 10V D3 = 1N4148 C2 = 1000pF, 10V T1 = Q2004L4 (Typical Triac) C3 = 1000pF, 1kV or Q2004F41 (Typical Triac) C4 220VAC APPLICATION R1 = 39kΩ, 2W R2 = 910kΩ, 1/4W (1) R4 = 470kΩ, 1/4W, 1% D1 = 1N4005 T1 = Q4004L4 (Typical Triac) or Q4004F41 (Typical Triac) All other values remain the same. (1) Resistor should be placed adjacent to Pin 1. NOTE 1: Connect MODE (Pin 6) for desired Brightness Step Sequence (See Table 1). NOTE 2: A good PCB layout using through-hole components will provide protection for ESD introduced at the Touch Plate in the range of 25kV. Using surface mount components and/or a poor PCB layout can reduce the ESD protection. The OEM can increase the ESD protection provided by the product with any combination of the following steps: Step 1: The most effective and least costly way to increase ESD protection is to create a spark gap around the Touch Plate input on the PCB. This will increase ESD protection on a good PCB layout to abut 35kV. The gap should be made with a split metal ring with each side of the metal ring connected back to opposite sides of the AC line. This ensures that a path for the spark back to house ground through AC Neutral exists independent of line plug polarity. The split ring and the center conduction plate should be constructed so that the spacing between them conforms to UL requirements. The spark gap will absorb most of the ESD leaving a remnant of about 10kV for the rest of the circuit to absorb. Step 2: Increase R3 from 1kΩ to 5.1kΩ and add C7, a 0.1µF capacitor, between VDD and Vss. (A minimal loss in touch sensitivity may be experienced.) Step 3: Replace diodes D2 and D3 (1N4148) with Schottky diodes (1N5819 or similar) 7541-011706-4 FIGURE 5. TOUCH LAMP APPLICATION SCHEMATIC -V LOAD R1 D1 C1 AC MAINS Z1 + MT2 T1 G MT1 SEE NOTE1 R6 + +V C6 R5 7 8 C2 TRIG 6 V SS MODE - 5 CONT C7* LS7541 (SEE NOTE 2) CLOCK SYNC V DD TOUCH R2 1 2 3 4 D2 R4 D3 TOUCH PLATE (LAMP BODY) C3 C4 R3 The Figure 5 Application Schematic functions identically to that shown in Figure 4 with one less component. Referencing Triac T1 to the +V power supply of the IC eliminates the need to AC couple the TRIAC pulse to the Triac Gate thereby eliminating component C5. 7541-051106-5