LINER LT1817

LT6210/LT6211
Single/Dual Programmable
Supply Current, R-R Output,
Current Feedback Amplifiers
Features
Description
Programmable Supply Current and Bandwidth:
10MHz at 300µA per Amplifier up to
200MHz at 6mA per Amplifier
n Rail-to-Rail Output:
0.05V to 2.85V on 3V Single Supply
n High Slew Rate: 700V/µs
n High Output Drive:
±75mA Minimum Output Current
n C-Load™ Op Amp Drives All Capacitive Loads
n Low Distortion:
–70dB HD2 at 1MHz 2VP-P
–75dB HD3 at 1MHz 2VP-P
n Fast Settling:
20ns 0.1% Settling for 2V Step
n Excellent Video Performance Into 150Ω Load:
Differential Gain of 0.20%, Differential Phase of 0.10°
n Wide Supply Range:
3V to 12V Single Supply
±1.5V to ±6V Dual Supplies
n Small Size:
Low Profile (1mm) 6-Lead ThinSOT™,
3mm × 3mm × 0.8mm DFN and 10-Lead MSOP Packages
The LT®6210/LT6211 are single/dual current feedback
amplifiers with externally programmable supply current
and bandwidth ranging from 10MHz at 300µA per amplifier to 200MHz at 6mA per amplifier. They feature a low
distortion rail-to-rail output stage, 700V/µs slew rate and
a minimum output current drive of 75mA.
n
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and C-Load
and ThinSOT are trademarks of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
Typical Application
The LT6210/LT6211 operate on supplies as low as a single
3V and up to either 12V or ±6V. The ISET pin allows for the
optimization of quiescent current for specific bandwidth,
distortion or slew rate requirements. Regardless of supply
voltage, the supply current is programmable from just
300µA to 6mA per amplifier with an external resistor or
current source.
The LT6210 is available in the low profile (1mm) 6-lead
TSOT-23 package. The LT6211 is available in the 10-lead
MSOP and the 3mm × 3mm × 0.8mm DFN packages.
Applications
Buffers
Video Amplifers
n Cable Drivers
n Mobile Communication
n Low Power/Battery Applications
n
n
Small Signal Response vs Supply Current
Line Driver Configuration for Various Supply Currents
9
3
IS = 3mA
3
4
6
+
1
LT6210
75Ω
75Ω
CABLE
VOUT
5
–
2
75Ω
RSET
–5V
RF
RG
IS
6mA
3mA
300µA
RSET
20k
56k
1M
RG
887Ω
1.1k
11k
RF
887Ω
1.1k
11k
RLOAD
150Ω
150Ω
1k
6210 TA01
6
IS = 6mA
IS = 300µA
3
–3
0
–3
0
–6
VS = ±5V
AV = 2
TA = 25°C
VOUT = 100mVP-P
–6
0.1
1
10
100
FREQUENCY (MHz)
GAIN AT VOUT (dB)
VIN
GAIN AT LT6210 OUTPUT (dB)
5V
–9
–12
1000
6210 TA01b
62101fc
1
LT6210/LT6211
Absolute Maximum Ratings
(Note 1)
Total Supply Voltage (V+ to V–)...............................13.2V
Input Current (Note 8)......................................±10mA
Output Current..................................................±80mA
Output Short-Circuit Duration (Note 2)............. Indefinite
Operating Temperature Range (Note 3).... –40°C to 85°C
Specified Temperature Range (Note 4)..... –40°C to 85°C
Junction Temperature (Note 5).............................. 150°C
Junction Temperature (DD Package)...................... 150°C
Storage Temperature Range ................... –65°C to 150°C
Storage Temperature Range
(DD Package)...................................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)................... 300°C
Pin Configuration
TOP VIEW
OUT A
1
–IN A
2
+IN A
3
ISET A
4
V
–
10 V+
–
+
5
11
–
+
TOP VIEW
TOP VIEW
9 OUT B
OUT A
–IN A
+IN A
ISET A
V–
8 –IN B
7 +IN B
6 ISET B
1
2
3
4
5
–
+
–
+
10
9
8
7
6
V+
OUT B
–IN B
+IN B
ISET B
MS PACKAGE
10-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 120°C/W (NOTE 5)
DD PACKAGE
10-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 43°C/W (NOTE 5)
EXPOSED PAD (PIN 11) CONNECTED TO V–
(PCB CONNECTION OPTIONAL)
6 V+
OUT 1
V– 2
+IN 3
+
–
5 ISET
4 –IN
S6 PACKAGE
6-LEAD PLASTIC TSOT-23
TJMAX = 150°C, θJA = 230°C/W (NOTE 5)
order information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT6211CDD#PBF
LT6211CDD#TRPBF
LBCD
10-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LT6211IDD#PBF
LT6211IDD#TRPBF
LBCD
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT6211CMS#PBF
LT6211CMS#TRPBF
LTBBN
10-Lead Plastic MSOP
0°C to 70°C
LT6211IMS#PBF
LT6211IMS#TRPBF
LTBBP
10-Lead Plastic MSOP
–40°C to 85°C
LT6210CS6#PBF
LT6210CS6#TRPBF
LTA3
6-Lead Plastic TSOT-23
0°C to 70°C
LT6210IS6#PBF
LT6210IS6#TRPBF
LTA3
6-Lead Plastic TSOT-23
–40°C to 85°C
LEAD BASED FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
SPECIFIED TEMPERATURE RANGE
LT6211CDD
LT6211CDD#TR
LBCD
10-Lead (3mm × 3mm) Plastic DFN
0°C to 70°C
LT6211IDD
LT6211IDD#TR
LBCD
10-Lead (3mm × 3mm) Plastic DFN
–40°C to 85°C
LT6211CMS
LT6211CMS#TR
LTBBN
10-Lead Plastic MSOP
0°C to 70°C
LT6211IMS
LT6211IMS#TR
LTBBP
10-Lead Plastic MSOP
–40°C to 85°C
LT6210CS6
LT6210CS6#TR
LTA3
6-Lead Plastic TSOT-23
0°C to 70°C
LT6210IS6
LT6210IS6#TR
LTA3
6-Lead Plastic TSOT-23
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
62101fc
2
LT6210/LT6211
Electrical
Characteristics
(IS = 6mA per Amplifier) The l denotes the specifications which
apply over the specified operating temperature range, otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 20k to
ground, AV = +2, RF = RG = 887Ω, RL = 150Ω; For V+ = 3V, V– = 0V: RSET = 0Ω to V–, AV = +2, RF = 887Ω, RG = 887Ω to 1.5V,
RL = 150Ω to 1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 6mA
SYMBOL PARAMETER
VOS
CONDITIONS
MIN
Input Offset Voltage
TYP
MAX
–1
TYP
MAX
UNITS
±6
±9
–1
±6.5
±10
mV
mV
–3.5
±7
±9
–3
±6.5
±8
µA
µA
–13.5
±39
±55
2.5
±25
±40
µA
µA
l
IIN+
Noninverting Input Current
l
IIN–
Inverting Input Current
V+ = 3V, V– = 0V, IS = 6mA
l
MIN
en
Input Noise Voltage Density
f = 1kHz, RF = 887Ω,
RG = 46.4Ω, RS = 0Ω
6.5
6.5
nV/√Hz
+in
Input Noise Current Density
f = 1kHz
4.5
4.5
pA/√Hz
Input Noise Current Density
f = 1kHz
25
25
pA/√Hz
1.7
MΩ
2
pF
–in
= V+ – 1.2V to V– + 1.2V
+
Noninverting Input Resistance
VIN
CIN
+
Noninverting Input Capacitance
f = 100kHz
VINH
Input Voltage Range, High
(Note 10)
l
VINL
Input Voltage Range, Low
(Note 10)
l
VOUTH
Output Voltage Swing, High
RL = 1k (Note 11)
RL = 150Ω (Note 11)
RL = 150Ω (Note 11)
RIN
VOUTL
Output Voltage Swing, Low
RL = 1k (Note 11)
RL = 150Ω (Note 11)
RL = 150Ω (Note 11)
CMRR
Common Mode Rejection Ratio
VIN = V+ – 1.2V to V– + 1.2V
l
Inverting Input Current
Common Mode Rejection
VIN = V+ – 1.2V to V– + 1.2V
PSRR
Power Supply Rejection Ratio
VS = ±1.5V to ±6V (Note 6)
–IPSRR
Inverting Input Current Power
Supply Rejection
VS = ±1.5V to ±6V (Note 6)
IS
Supply Current per Amplifier
2
0.3
2
l
3.8
4.2
–4.2
4.4
4.2
l
46
43
0.15
60
2.85
2.75
0.05
0.1
–4.55
–4.4
±1.5
±2
60
V
1.2
V
V
V
V
0.3
0.35
V
V
V
46
dB
dB
0.2
µA/V
µA/V
85
dB
2
±7
±8
2
±7
±8
µA/V
µA/V
6
8.5
10
5.8
8.3
9
mA
mA
l
l
2.65
2.6
85
2.2
0.8
50
l
l
1.8
–3.8
4.8
4.6
–4.95
–4.8
l
–ICMRR
0.5
62101fc
3
LT6210/LT6211
Electrical
Characteristics
(IS = 6mA per Amplifier) The l denotes the specifications which
apply over the specified operating temperature range, otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 20k to
ground, AV = +2, RF = RG = 887Ω, RL = 150Ω; For V+ = 3V, V– = 0V: RSET = 0Ω to V–, AV = +2, RF = 887Ω, RG = 887Ω to 1.5V,
RL = 150Ω to 1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 6mA
SYMBOL PARAMETER
IOUT
CONDITIONS
Maximum Output Current
RL = 0Ω (Notes 7, 11)
–
MIN
l
= V+ – 1.2V to V– + 1.2V
ROL
Transimpedance, ∆VOUT/∆IIN
VOUT
SR
Slew Rate
(Note 8)
tpd
Propagation Delay
BW
TYP
MAX
±75
V+ = 3V, V– = 0V, IS = 6mA
MIN
TYP
MAX
±45
65
UNITS
mA
65
115
115
kΩ
500
700
200
V/µs
50% VIN to 50% VOUT,
100mVP-P, Larger of tpd+, tpd–
1.5
2.4
ns
–3dB Bandwidth
<1dB Peaking, AV = 1
200
120
MHz
ts
Settling Time
To 0.1% of VFINAL, VSTEP = 2V
20
25
ns
tf, tr
Small-Signal Rise and Fall Time 10% to 90%, VOUT = 100mVP-P
2
3.5
ns
dG
Differential Gain
(Note 9)
0.20
0.35
%
dP
Differential Phase
(Note 9)
0.10
0.20
Deg
HD2
2nd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–70
–65
dBc
HD3
3rd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–75
–75
dBc
(IS = 3mA per Amplifier) The l denotes the specifications which apply over the specified operating temperature range,
otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 56k to ground, AV = +2, RF = RG = 1.1k, RL = 150Ω; For V+ = 3V,
V– = 0V: RSET = 10k to V–, AV = +2, RF = 1.27k, RG = 1.27k to 1.5V, RL = 150Ω to 1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 3mA
SYMBOL PARAMETER
VOS
CONDITIONS
MIN
Input Offset Voltage
TYP
MAX
TYP
MAX
UNITS
–1
±5.5
±8.5
–1.5
±5.5
±8.5
mV
mV
–1.5
±5
±7
–1.5
±5
±7
µA
µA
–12
±36
±52
–3
±15
±20
µA
µA
l
IIN+
Noninverting Input Current
l
IIN–
Inverting Input Current
l
en
Input Noise Voltage Density
f = 1kHz, RF = 1.1k,
RG = 57.6Ω, RS = 0Ω
+in
Input Noise Current Density
–in
Input Noise Current Density
7
nV/√Hz
f = 1kHz
1.5
1.5
pA/√Hz
f = 1kHz
15
15
pA/√Hz
2.5
MΩ
2
pF
2.1
V
= V+ – 1.2V to V– + 1.2V
Noninverting Input Resistance
VIN
CIN
+
Noninverting Input Capacitance
f = 100kHz
VINH
Input Voltage Range, High
(Note 10)
l
VINL
Input Voltage Range, Low
(Note 10)
l
VOUTH
Output Voltage Swing, High
RL = 1k (Note 11)
RL = 150Ω (Note 11)
RL = 150Ω (Note 11)
VOUTL
CMRR
Output Voltage Swing, Low
Common Mode Rejection Ratio
RL = 1k (Note 11)
RL = 150Ω (Note 11)
RL = 150Ω (Note 11)
VIN
l
Inverting Input Current
Common Mode Rejection
0.5
3
1
2
l
3.8
4.1
–4.1
4.3
4.1
l
= V+ – 1.2V to V– + 1.2V
VIN = V+ – 1.2V to V– + 1.2V
46
43
–3.8
0.9
2.6
2.55
–4.55
–4.4
50
0.3
l
1.8
4.8
4.6
–4.95
–4.8
l
–ICMRR
MIN
7
+
RIN
V+ = 3V, V– = 0V, IS = 3mA
±1.5
±2
1.2
2.9
2.8
0.05
0.1
V
V
V
V
0.3
0.35
V
V
V
46
dB
dB
0.4
µA/V
µA/V
62101fc
4
LT6210/LT6211
Electrical
Characteristics
(IS = 3mA per Amplifier) The l denotes the specifications which
apply over the specified operating temperature range, otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 56k to
ground, AV = +2, RF = RG = 1.1k, RL = 150Ω; For V+ = 3V, V– = 0V: RSET = 10k to V–, AV = +2, RF = 1.27k, RG = 1.27k to 1.5V,
RL = 150Ω to 1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 3mA
SYMBOL PARAMETER
CONDITIONS
PSRR
Power Supply Rejection Ratio
VS = ±1.5V to ±6V (Note 6)
–IPSRR
Inverting Input Current Power
Supply Rejection
VS = ±1.5V to ±6V (Note 6)
l
MIN
TYP
60
85
Maximum Output Current
RL = 0Ω (Notes 7, 11)
–
l
= V+ – 1.2V to V– + 1.2V
ROL
Transimpedance, ∆VOUT/∆IIN
VOUT
SR
Slew Rate
(Note 8)
tpd
Propagation Delay
BW
TYP
60
85
MAX
UNITS
dB
±7
±8
1.5
±7
±8
µA/V
µA/V
3
4.1
4.55
3
4.1
4.4
mA
mA
l
IOUT
MIN
1.5
l
Supply Current per Amplifier
IS
MAX
V+ = 3V, V– = 0V, IS = 3mA
±70
±45
65
mA
65
120
120
kΩ
450
600
150
V/µs
50% VIN to 50% VOUT,
100mVP-P, Larger of tpd+, tpd–
3.1
4.7
ns
–3dB Bandwidth
<1dB Peaking, AV = 1
100
70
MHz
ts
Settling Time
To 0.1% of VFINAL, VSTEP = 2V
20
25
ns
tf, tr
Small-Signal Rise and Fall Time 10% to 90%, VOUT = 100mVP-P
3
5.6
ns
dG
Differential Gain
(Note 9)
0.35
0.42
%
dP
Differential Phase
(Note 9)
0.30
0.44
Deg
HD2
2nd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–65
–60
dBc
HD3
3rd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–65
–65
dBc
(IS = 300µA per Amplifier) The l denotes the specifications which apply over the specified operating temperature range,
otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 1M to ground, AV = +2, RF = RG = 11k, RL = 1k; For V+ = 3V,
V– = 0V: RSET = 270k to V–, AV = +2, RF = 9.31k, RG = 9.31k to 1.5V, RL = 1k to 1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 300µA
SYMBOL PARAMETER
VOS
MIN
CONDITIONS
Input Offset Voltage
TYP
MAX
–1
TYP
MAX
UNITS
±4.5
±8
–1.5
±4.5
±8
mV
mV
0.2
±1
±2
0.2
±1
±1.5
µA
µA
–3
±8.5
±11
–0.5
±3
±4.5
µA
µA
l
IIN+
Noninverting Input Current
l
IIN–
Inverting Input Current
V+ = 3V, V– = 0V, IS = 300µA
l
MIN
en
Input Noise Voltage Density
f = 1kHz, RF = 13k,
RG = 681Ω, RS = 0Ω
13.5
13.5
nV/√Hz
+in
Input Noise Current Density
f = 1kHz
0.75
0.75
pA/√Hz
–in
Input Noise Current Density
f = 1kHz
5
5
pA/√Hz
15
MΩ
2
pF
2.1
V
+
= V+ – 1.2V to V– + 1.2V
RIN
Noninverting Input Resistance
VIN
(Note 8)
CIN+
Noninverting Input Capacitance
f = 100kHz
VINH
Input Voltage Range, High
(Note 10)
l
VINL
Input Voltage Range, Low
(Note 10)
l
VOUTH
Output Voltage Swing, High
RL = 1k (Note 11)
l
Output Voltage Swing, Low
25
1
2
l
VOUTL
1
RL = 1k (Note 11)
3.8
4.1
–4.1
4.75
4.7
–3.8
4.85
–4.95
l
1.8
0.9
2.75
2.7
–4.85
–4.8
1.2
2.85
0.05
V
V
V
0.15
0.2
V
V
62101fc
5
LT6210/LT6211
Electrical
Characteristics
(IS = 300µA per Amplifier) The l denotes the specifications which
apply over the specified operating temperature range, otherwise specifications are at TA = 25°C. For V+ = 5V, V– = –5V: RSET = 1M to
ground, AV = +2, RF = RG = 11k, RL = 1k; For V+ = 3V, V– = 0V: RSET = 270k to V–, AV = +2, RF = 9.31k, RG = 9.31k to 1.5V, RL = 1k to
1.5V unless otherwise specified.
V+ = 5V, V– = –5V, IS = 300µA
SYMBOL PARAMETER
CONDITIONS
CMRR
VIN = V+ – 1.2V to V– + 1.2V
Common Mode Rejection Ratio
l
Inverting Input Current
Common Mode Rejection
VIN = V+ – 1.2V to V– + 1.2V
PSRR
Power Supply Rejection Ratio
VS = ±1.5V to ±6V (Note 6)
–IPSRR
Inverting Input Current Power
Supply Rejection
VS = ±1.5V to ±6V (Note 6)
–ICMRR
IS
MIN
TYP
46
43
50
0.15
l
l
60
ROL
Maximum Output Current
RL = 0Ω (Notes 7, 11)
–
Transimpedance, ∆VOUT/∆IIN
VOUT
= V+ – 1.2V to V– + 1.2V
l
60
TYP
MAX
UNITS
46
dB
dB
0.2
µA/V
µA/V
85
dB
0.4
±2.2
±4
0.4
±2.2
±4
µA/V
µA/V
0.3
0.525
0.6
0.3
0.38
0.43
mA
mA
l
IOUT
MIN
±1.5
±2
85
l
Supply Current per Amplifier
MAX
V+ = 3V, V– = 0V, IS = 300µA
±30
±10
300
660
120
65
mA
120
kΩ
SR
Slew Rate
(Note 8)
170
20
V/µs
tpd
Propagation Delay
50% VIN to 50% VOUT,
100mVP-P, Larger of tpd+, tpd–
30
50
ns
BW
–3dB Bandwidth
<1dB Peaking, AV = 1
10
7.5
MHz
ts
Settling Time
To 0.1% of VFINAL, VSTEP = 2V
200
300
ns
tf, tr
Small-Signal Rise and Fall Time 10% to 90%, VOUT = 100mVP-P
40
50
ns
HD2
2nd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–40
––45
dBc
HD3
3rd Harmonic Distortion
f = 1MHz, VOUT = 2VP-P
–45
–45
dBc
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: As long as output current and junction temperature are kept
below the absolute maximum ratings, no damage to the part will occur.
Depending on the supply voltage, a heat sink may be required.
Note 3: The LT6210C/LT6211C is guaranteed functional over the operating
temperature range of –40°C to 85°C.
Note 4: The LT6210C/LT6211C is guaranteed to meet specified
performance from 0°C to 70°C. The LT6210C/LT6211C is designed,
characterized and expected to meet specified performance from –40°C and
85°C but is not tested or QA sampled at these temperatures. The LT6210I/
LT6211I is guaranteed to meet specified performance from –40°C to 85°C.
Note 5: The LT6210 with no metal connected to the V– pin has a θJA of
230°C/W, however, thermal resistances vary depending upon the amount
of PC board metal attached to Pin 2 of the device. With the LT6210
mounted on a 2500mm2 3/32" FR-4 board covered with 2oz copper on
both sides and with just 20mm2 of copper attached to Pin 2, θJA drops to
160°C/W. Thermal performance can be improved even further by using a
4-layer board or by attaching more metal area to Pin 2.
Thermal resistance of the LT6211 in MSOP-10 is specified for a 2500mm2
3/32" FR-4 board covered with 2oz copper on both sides and with 100mm2
of copper attached to Pin 5. Its performance can also be increased with
additional copper much like the LT6210.
To achieve the specified θJA of 43°C/W for the LT6211 DFN-10, the
exposed pad must be soldered to the PCB. In this package, θJA will benefit
from increased copper area attached to the exposed pad.
TJ is calculated from the ambient temperature TA and the power
dissipation PD according to the following formula:
TJ = TA + (PD • θJA)
The maximum power dissipation can be calculated by:
PD(MAX) = (VS • IS(MAX)) + (VS/2)2/RLOAD
Note 6: For PSRR and –IPSRR testing, the current into the ISET pin is
constant, maintaining a consistent LT6210/LT6211 quiescent bias point.
A graph of PSRR vs Frequency is included in the Typical Performance
Characteristics showing +PSRR and –PSRR with RSET connecting ISET to
ground.
Note 7: While the LT6210 and LT6211 circuitry is capable of significant
output current even beyond the levels specified, sustained shortcircuit current exceeding the Absolute Maximum Rating of ±80mA may
permanently damage the device.
Note 8: This parameter is guaranteed to meet specified performance
through design and characterization. It is not production tested.
Note 9: Differential gain and phase are measured using a Tektronix
TSG120YC/NTSC signal generator and a Tektronix 1780R Video
Measurement Set. The resolution of this equipment is 0.1% and 0.1°. Five
identical amplifier stages were cascaded giving an effective resolution of
0.02% and 0.02°.
Note 10: Input voltage range on ±5V dual supplies is guaranteed by
CMRR. On 3V single supply it is guaranteed by design and by correlation
to the ±5V input voltage range limits.
Note 11: This parameter is tested by forcing a 50mV differential voltage
between the inverting and noninverting inputs.
62101fc
6
LT6210/LT6211
Typical AC Performance
VS (V)
IS (mA) per
Amplifier
RSET (Ω)
AV
RL (Ω)
RF (Ω)
RG (Ω)
SMALL-SIGNAL
–3dB BW, <1dB PEAKING (MHz)
SMALL-SIGNAL
±0.1dB BW (MHz)
±5
6
20k
1
150
1200
—
200
30
±5
6
20k
2
150
887
887
160
30
±5
6
20k
–1
150
698
698
140
20
±5
3
56k
1
150
1690
—
100
15
±5
3
56k
2
150
1100
1100
100
15
±5
3
56k
–1
150
1200
1200
80
15
±5
0.3
1M
1
1k
13.7k
—
10
2
±5
0.3
1M
2
1k
11k
11k
10
2
±5
0.3
1M
–1
1k
10k
10k
10
1.8
3, 0
6
0
1
150
1100
—
120
20
3, 0
6
0
2
150
887
887
100
20
3, 0
6
0
–1
150
806
806
100
20
3, 0
3
10k
1
150
1540
—
70
15
3, 0
3
10k
2
150
1270
1270
60
15
3, 0
3
10k
–1
150
1200
1200
60
15
3, 0
0.3
270k
1
1k
13k
—
7.5
2
3, 0
0.3
270k
2
1k
9.31k
9.31k
7
1.5
3, 0
0.3
270k
–1
1k
10k
10k
7
1.5
Typical Performance Characteristics
Supply Current per Amplifier vs
Temperature
4.00
RL = ∞
5.5
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
6.0
VS = ±5V
RSET = 20k TO GND
VS = ±1.5V
RSET = 0Ω TO V–
5.0
4.5
–50 –25
400
RL = ∞
380
3.75
7.0
6.5
Supply Current per Amplifier vs
Temperature
3.25
VS = ±1.5V
RSET = 10k TO V–
3.00
VS = ±5V
RSET = 56k TO GND
2.75
2.50
50
25
75
0
TEMPERATURE (°C)
100
125
6210 G01
340
320
VS = ±5V
RSET = 1M TO GND
300
VS = ±1.5V
RSET = 270k TO V–
280
260
240
2.25
2.00
–50
RL = ∞
360
3.50
SUPPLY CURRENT (µA)
7.5
Supply Current per Amplifier vs
Temperature
220
–25
0
25
50
75
TEMPERATURE (°C)
100
125
6210 G02
200
–50
–25
50
25
0
75
TEMPERATURE (°C)
100
125
6210 G03
62101fc
7
LT6210/LT6211
Typical Performance Characteristics
1
0.1
0.001
0.01
0.1
1
10
–in
en
10
+in
1
0.1
0.001
100
0.01
FREQUENCY (kHz)
0.1
1
10
20
5.0
0
–5
INPUT COMMON MODE LIMIT (V)
OFFSET VOLTAGE (mV)
5
IS = 3mA
RF = 1690Ω
RL = 150Ω
–10 V = ±5V
S
IS = 6mA
AV = 1
RF = 1200Ω
–15 T = 25°C
A
RL = 150Ω
TYPICAL PART
–20
–5 –4 –3 –2 –1 0 1 2 3 4
INPUT COMMON MODE VOLTAGE (V)
IS = 6mA
RF = 1200Ω
RL = 150Ω
IS = 3mA
RF = 1690Ω
RL = 150Ω
–4.0
–4.5
VS = ±5V
AV = 1
CMRR > 48dB
TYPICAL PART
IS = 300µA
RF = 13.7k
RL = 1k
50
25
75
0
TEMPERATURE (°C)
–4.4
–4.6
–4.8
–5.0
–50
VS = ±5V
VCM = 0V
∆VOS = 50mV
IS = 6mA
RL = 1k
IS = 6mA
RL = 150Ω
100
125
62101 G08
0
25
50
1.1
–1.2
0
75
100
125
6210 G10
–1.5
–50
IS = 3mA
RF = 1540Ω
RL = 150Ω
–0.5
VS = ±1.5V
IS = 300µA
–1.0 AV = 1
RF = 13k
CMRR >46dB
RL = 1k
TYPICAL PART
–1.5
50
100
25
75
–50 –25
0
TEMPERATURE (°C)
125
Output Voltage Swing vs ILOAD
IS = 3mA
IS = 6mA
4.4
4.2
4.0
IS = 300µA
3.8
3.6
VS = ±5V
VCM = 0V
3.2 ∆VOS = 50mV
TA = 25°C
3.0
0
10 20
3.4
OUTPUT LOW
–25
IS = 6mA
RF = 1100Ω
RL = 150Ω
4.6
IS = 6mA
RL = 100Ω
IS = 300µA
RL = 1k
–1.4
TEMPERATURE (°C)
0.5
4.8
IS = 6mA
RL = 100Ω
VS = ±1.5V
VCM = 0V
∆VOS = 50mV
–1.1
–1.3
OUTPUT LOW
–25
IS = 300µA
RL = 1k
1.2
100
62101 G09
OUTPUT HIGH
1.3
IS = 300µA
RL = 1k
10
IS = 300µA
RF = 13k
RL = 1k
1.0
5.0
1.4
OUTPUT HIGH
IS = 300µA
RL = 1k
1
1.5
1.5
IS = 6mA
RL = 150Ω
0.1
62101GO6
Output Voltage Swing vs
Temperature
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
4.4
0.01
Input Common Mode Range vs
Temperature
4.0
–5.0
–50 –25
5
5.0
IS = 6mA
RL = 1k
+in
1
0.1
0.001
100
IS = 300µA
RF = 13.7k
RL = 1k
4.5
Output Voltage Swing vs
Temperature
4.6
–in
FREQUENCY (kHz)
62101 G07
4.8
en
Input Common Mode Range vs
Temperature
IS = 300µA
RF = 13.7k
RL = 1k
VS = ±5V
RL = 1k
TA = 25°C
62101GO5
Input Offset Voltage vs Input
Common Mode Voltage
15
Input Noise Spectral Density
(IS = 300µA per Amplifier)
10
FREQUENCY (kHz)
62101GO4
10
100
INPUT COMMON MODE LIMIT (V)
en
VS = ±5V
RL = 150Ω
TA = 25°C
INPUT NOISE (nV/√Hz OR pA/√Hz)
+in
Input Noise Spectral Density
(IS = 3mA per Amplifier)
OUTPUT VOLTAGE (V)
INPUT NOISE (nV/√Hz OR pA/√Hz)
–in
10
100
VS = ±5V
RL = 150Ω
TA = 25°C
INPUT NOISE (nV/√Hz OR pA/√Hz)
100
Input Noise Spectral Density
(IS = 6mA per Amplifier)
(Supply Current Is Measured Per Amplifier)
0
25
50
75
TEMPERATURE (°C)
100
125
6210 G11
40
50
60
30
LOAD CURRENT (mA)
70
6210 G12
62101fc
8
LT6210/LT6211
Typical Performance Characteristics
Output Voltage Swing vs ILOAD
Output Voltage Swing vs ILOAD
VS = ±5V
–3.2 VCM = 0V
∆VOS = 50mV
–3.4 T = 25°C
A
–4.0
–4.2
–4.4
IS = 300µA
IS = 3mA
IS = 6mA
0
10
20
40
50
60
30
LOAD CURRENT (mA)
70
1.0
0.8
IS = 300µA
0.6
0.4
VS = ±1.5V
VCM = 0V
0.2 ∆V
OS = 50mV
TA = 25°C
0
0
40
50
60
10 20
30
LOAD CURRENT (mA)
6210 G13
+PSRR
60
CMRR
40
30
20
10
9
0.01
0.1
1
FREQUENCY (MHz)
50
40
CMRR
30
20
6210 G16
Frequency Response vs Closed
Loop Gain (IS = 6mA per Amplifier)
9
AV = 2
RF = RG = 887Ω
6
3
0
AV = 1
RF = 1.2k
VS = ±5V
–3 R = 150Ω
L
AV = –1
TA = 25°C
RF = RG = 698Ω
VOUT = 100mVP-P
–6
0.1
10
100
1
FREQUENCY (MHz)
1000
6210 G19
IS = 3mA
IS = 6mA
0
10
20
40
50
60
30
LOAD CURRENT (mA)
70
6210 G15
70
VS = ±5V
RL = 150Ω
TA = 25°C
–PSRR
60
CMRR and PSRR vs Frequency
(IS = 300µA per Amplifier)
VS = ±5V
RL = 1k
TA = 25°C
–PSRR
+PSRR
50
40
CMRR
30
20
10
0
0.001
100
10
GAIN (dB)
GAIN (dB)
6
–1.5
70
10
0
0.001
IS = 300µA
–1.1
CMRR and PSRR vs Frequency
(IS = 3mA per Amplifier)
+PSRR
REJECTION RATIO (dB)
REJECTION RATIO (dB)
50
70
VS = ±5V
RL = 150Ω
TA = 25°C
60
–0.9
6210 G14
CMRR and PSRR vs Frequency
(IS = 6mA per Amplifier)
–PSRR
–0.7
REJECTION RATIO (dB)
70
–0.5
–1.3
0.01
0.1
1
FREQUENCY (MHz)
10
0
0.001
100
6210 G17
6
0
AV = –1
VS = ±5V
RF = RG = 1200Ω
–3 R = 150Ω
L
TA = 25°C
AV = 1
VOUT = 100mVP-P RF = 1690Ω
–6
0.1
10
100
1
FREQUENCY (MHz)
1000
6210 G20
0.1
1
FREQUENCY (MHz)
10
6210 G18
9
AV = 2
RF = RG = 1100Ω
3
0.01
Frequency Response vs Closed
Loop Gain (IS = 300µA per
Amplifier)
Frequency Response vs Closed
Loop Gain (IS = 3mA per Amplifier)
GAIN (dB)
–5.0
IS = 3mA
IS = 6mA
OUTPUT VOLTAGE (V)
–3.8
–4.8
VS = ±1.5V
VCM = 0V
∆VOS = 50mV
–0.3 T = 25°C
A
–0.1
1.2
–3.6
–4.6
Output Voltage Swing vs ILOAD
1.4
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
–3.0
(Supply Current Is Measured Per Amplifier)
AV = 2
RF = RG = 11k
3
0
AV = –1
V = ±5V
RF = RG = 10k
–3 RS = 150Ω
L
TA = 25°C
VOUT = 100mVP-P
–6
0.1
10
1
FREQUENCY (MHz)
AV = 1
RF = 13.7k
100
6210 G21
62101fc
9
LT6210/LT6211
Typical Performance Characteristics
0
2nd and 3rd Harmonic Distortion vs
Frequency (IS = 3mA per Amplifier)
VS = ±5V
RF = RG = 1.1k
VOUT = 2VP-P
RL = 150Ω
TA = 25°C
–10
–20
–40
–50
HD2
–60
–70
HD3
–80
–30
–20
HD2
–40
–50
–60
–70
HD3
–80
–90
100
0.1
1
10
FREQUENCY (MHz)
6210 G22
7
IS = 6mA
RF = RG = 887Ω
RL = 150Ω
6
5
4
3
IS = 300µA
RF = RG = 11k
RL = 1k
2
1
0
0.1
1
10
FREQUENCY (MHz)
1000
OUTPUT IMPEDANCE (Ω)
OUTPUT VOLTAGE SWING (VP-P)
8
10
IS = 6mA
RF = RG = 887Ω
RL = 150Ω
1
OVERSHOOT (%)
20
IS = 6mA
RF = RG = 887Ω
RL = 150Ω
10
10
VS = ±5V
AV = 2
VOUT = 100mVP-P
TA = 25°C
100
1000
CAPACITIVE LOAD (pF)
10000
6210 G28
OUTPUT SERIES RESISTANCE (Ω)
50
30
10
6210 G24
1
10
FREQUENCY (MHz)
100
500
100
RL = ∞
80
RL = 150Ω
60
40
VS = ±5V
20 IS = 6mA
RF = RG = 887Ω
TA = 25°C
0
0.1
10
1
FREQUENCY (MHz)
100
Maximum Capacitive Load vs
Feedback Resistor
VS = ±5V
OVERSHOOT < 10%
VOUT = 100mVP-P
IS = 6mA
RF = RG = 887Ω
RL = ∞
TA = 25°C
45
40
35
30
500
6210 G27
Maximum Capacitive Load vs
Output Series Resistor
IS = 300µA
RF = RG = 11k
RL = 1k
0.1
1
FREQUENCY (MHz)
6210 G26
70
40
–70
120
IS = 300µA
RF = RG = 11k
RL = 1k
0.1
0.1
100
IS = 3mA
RF = RG = 1100Ω
RL = 150Ω
HD3
–60
LT6211 Channel Separation
vs Frequency
100
Overshoot vs Capacitive Load
50
100
VS = ±5V
AV = 2
TA = 25°C
6210 G25
60
–50
Output Impedance vs Frequency
VS = ±5V
HD2, HD3 <–40dB
AV = 2
TA = 25°C
9
HD2
6210 G23
Maximum Undistorted Output
Sinusoid vs Frequency
10
–40
–100
0.01
CHANNEL SEPARATION (dB)
1
10
FREQUENCY (MHz)
VS = ±5V
RF = RG = 11k
VOUT = 2VP-P
RL = 1k
TA = 25°C
–90
–100
0.01
25
20
15
10000
CAPACITIVE LOAD (pF)
0.1
–30
2nd and 3rd Harmonic Distortion vs
Frequency (IS = 300µA per Amplifier)
–80
–90
–100
0.01
0
0
–10
DISTORTION (dBc)
0
VS = ±5V
–10 RF = RG = 887Ω
VOUT = 2VP-P
–20 R = 150Ω
L
–30 TA = 25°C
DISTORTION (dBc)
DISTORTION (dBc)
2nd and 3rd Harmonic Distortion vs
Frequency (IS = 6mA per Amplifier)
(Supply Current Is Measured Per Amplifier)
1000
VS = ±5V
AC PEAKING < 3dB
VOUT = 100mVP-P
IS = 6mA
RG = RF
RL = 150Ω
TA = 25°C
100
10
5
0
10
100
CAPACITIVE LOAD (pF)
1000
6210 G29
10
800
1000 1200 1400 1600 1800
FEEDBACK RESISTANCE (Ω)
2000
6210 G30
62101fc
10
LT6210/LT6211
Typical Performance Characteristics
–3dB Small-Signal Bandwidth
vs Supply Current
900
800
VS = ±5V
VS = ±1.5V
10
700
–30
VS = ±5V
AV = 2
VOUT = 7VP-P
TA = 25°C
HARMONIC DISTORTION (dBc)
1000
AV = 2
VOUT = 100mVP-P
TA = 25°C
100
1MHz 2nd and 3rd Harmonic
Distortion vs Supply Current
Slew Rate vs Supply Current
SLEW RATE (V/µs)
–3dB BANDWIDTH (MHz)
1000
(Supply Current Is Measured Per Amplifier)
RISING
EDGE RATE
600
500
FALLING
EDGE RATE
400
300
200
VS = ±5V
AV = 2
VOUT = 2VP-P
TA = 25°C
–40
–50
HD2
–60
HD3
–70
100
1
0.1
1
10
SUPPLY CURRENT PER AMPLIFIER (mA)
0
0.1
1
10
SUPPLY CURRENT PER AMPLIFIER (mA)
Small-Signal Transient Response
(IS = 6mA per Amplifier)
VS = ±5V
TIME (10ns/DIV)
VIN = ±25mV
RF = RG = 1.1k
RSET = 56k TO GND
RL = 150Ω
Large-Signal Transient Response
(IS = 6mA per Amplifier)
62101 G35
62101 G37
VS = ±5V
TIME (100ns/DIV)
VIN = ±25mV
RF = RG = 11k
RSET = 1M TO GND
RL = 1k
Large-Signal Transient Response
(IS = 3mA per Amplifier)
OUTPUT
(2V/DIV)
VS = ±5V
TIME (10ns/DIV)
VIN = ±1.75V
RF = RG = 887Ω
RSET = 20k TO GND
RL = 150Ω
Small-Signal Transient Response
(IS = 300µA per Amplifier)
OUTPUT
(50mV/DIV)
62101 G34
OUTPUT
(2V/DIV)
62101 G33
Small-Signal Transient Response
(IS = 3mA per Amplifier)
OUTPUT
(50mV/DIV)
VS = ±5V
TIME (10ns/DIV)
VIN = ±25mV
RF = RG = 887Ω
RSET = 20k TO GND
RL = 150Ω
10
1
SUPPLY CURRENT PER AMPLIFIER (mA)
62101 G32
62101 G31
OUTPUT
(50mV/DIV)
–80
0.1
62101 G36
Large-Signal Transient Response
(IS = 300µA per Amplifier)
OUTPUT
(2mV/DIV)
VS = ±5V
TIME (10ns/DIV)
VIN = ±1.75V
RF = RG = 1.1k
RSET = 56k TO GND
RL = 150Ω
62101 G38
VS = ±5V
TIME (100ns/DIV)
VIN = ±1.75V
RF = RG = 11k
RSET = 1M TO GND
RL = 1k
62101 G39
62101fc
11
LT6210/LT6211
Applications Information
Setting the Quiescent Operating Current (ISET Pin)
Input Considerations
The quiescent bias point of the LT6210/LT6211 is SET
with either an external resistor from the ISET pin to a
lower potential or by drawing a current out of the ISET
pin. However, the ISET pin is not designed to function as a
shutdown. The LT6211 uses two entirely independent bias
networks, so while each channel can be programmed for
a different supply current, neither ISET pin should be left
unconnected. A simplified schematic of the internal biasing structure can be seen in Figure 1. Figure 2 illustrates
the results of varying RSET on 3V and ±5V supplies. Note
that shorting the ISET pin under 3V operation results in
a quiescent bias of approximately 6mA. Attempting to
bias the LT6210/LT6211 at a current level higher than
6mA by using a smaller resistor may result in instability
and decreased performance. However, internal circuitry
clamps the supply current of the part at a safe level of
approximately 15mA in case of accidental connection of
the ISET pin directly to a negative potential.
The inputs of the LT6210/LT6211 are protected by backto-back diodes. If the differential input voltage exceeds
1.4V, the input current should be limited to less than the
absolute maximum ratings of ±10mA. In normal operation, the differential voltage between the inputs is small,
so the ±1.4V limit is generally not an issue. ESD diodes
protect both inputs, so although the part is not guaranteed
to function outside the common mode range, input voltages that exceed a diode beyond either supply will also
require current limiting to keep the input current below
the absolute maximum of ±10mA.
V+
6
600Ω
8k
TO
BIAS
CONTROL
5
6210 F01
SUPPLY CURRENT PER AMPLIFIER (mA)
Figure 1. Internal Bias Setting Circuitry
VS = ±5V
RSET TO GND
10
VS = 3V
RSET TO GND
1
TA = 25°C
RL = ∞
0.1
0.01
The small-signal bandwidth of the LT6210/LT6211 is set
by the external feedback resistors and the internal junction capacitances. As a result, the bandwidth is a function
of the quiescent supply current, the supply voltage, the
value of the feedback resistor, the closed-loop gain and the
load resistor. Refer to the Typical AC Performance table
for more information.
Layout and Passive Components
600Ω
ISET
Feedback Resistor Selection
0.1
1
10
100
1000
RSET PROGRAMMING RESISTOR (kΩ)
6210 F02
Figure 2. Setting RSET to Control IS
As with all high speed amplifiers, the LT6210/LT6211
require some attention to board layout. Low ESL/ESR
bypass capacitors should be placed directly at the positive
and negative supply (0.1µF ceramics are recommended).
For best transient performance, additional 4.7µF tantalums should be added. A ground plane is recommended
and trace lengths should be minimized, especially on the
inverting input lead.
Capacitance on the Inverting Input
Current feedback amplifiers require resistive feedback
from the output to the inverting input for stable operation.
Capacitance on the inverting input will cause peaking in
the frequency response and overshoot in the transient
response. Take care to minimize the stray capacitance at
the inverting input to ground and between the output and
the inverting input. If significant capacitance is unavoidable in a given application, an inverting gain configuration
should be considered. When configured inverting, the
amplifier inputs do not slew and the effect of parasitics
is greatly reduced.
62101fc
12
LT6210/LT6211
Applications Information
Capacitive Loads
The LT6210/LT6211 are stable with any capacitive load.
Although peaking and overshoot may result in the AC
transient response, the amplifier’s compensation decreases
bandwidth with increasing output capacitive load to ensure
stability. To maintain a response with minimal peaking, the
feedback resistor can be increased at the cost of bandwidth
as shown in the Typical Performance Characteristics.
Alternatively, a small resistor (5Ω to 35Ω) can be put in
series with the output to isolate the capacitive load from
the amplifier output. This has the advantage that the amplifier bandwidth is only reduced when the capacitive load
is present. The disadvantage of this technique is that the
gain is a function of the load resistance.
Power Supplies
The LT6210/LT6211 will operate on single supplies from
3V to 12V and on split supplies from ±1.5V to ±6V. If split
supplies of unequal absolute value are used, input offset
voltage and inverting input current will shift from the values
specified in the Electrical Characteristics table. Input offset
voltage will shift 2mV and inverting input current will shift
0.5µA for each volt of supply mismatch.
Slew Rate
Unlike a traditional voltage feedback op amp, the slew rate
of a current feedback amplifier is not independent of the
amplifier gain configuration. In a current feedback amplifier, both the input stage and the output stage have slew
rate limitations. In the inverting mode, and for gains of 2
or more in the noninverting mode, the signal amplitude
between the input pins is small and the overall slew rate
is that of the output stage. For gains less than 2 in the
noninverting mode, the overall slew rate is limited by the
input stage. The input slew rate of the LT6210/LT6211 on
±5V supplies with an RSET resistor of 20k (IS = 6mA) is
approximately 600V/µs and is set by internal currents and
capacitances. The output slew rate is additionally constrained by the value of the feedback resistor and internal
capacitance. At a gain of 2 with 887Ω feedback and gain
resistors, ±5V supplies and the same biasing as above,
the output slew rate is typically 700V/µs. Larger feedback
resistors, lower supply voltages and lower supply current
levels will all reduce slew rate. Input slew rates significantly
exceeding the output slew capability can actually decrease
slew performance in a positive gain configuration; the
cleanest transient response will be obtained from input
signals with slew rates slower than 1000V/µs.
Output Swing and Drive
The output stage of the LT6210/LT6211 consists of a pair
of class-AB biased common emitters that enable the output
to swing rail-to-rail. Since the amplifiers can potentially
deliver output currents well beyond the specified minimum
short-circuit current, care should be taken not to short the
output of the device indefinitely. Attention must be paid to
keep the junction temperature of the IC below the absolute
maximum rating of 150°C if the output is used to drive
low impedance loads. See Note 5 for details. Additionally,
the output of the amplifier has reverse-biased ESD diodes
connected to each supply. If the output is forced beyond
either supply, large currents will flow through these diodes.
If the current is limited to 80mA or less, no damage to
the part will occur.
62101fc
13
LT6210/LT6211
Typical Applications
3V Cable Driver with Active Termination
signal range. The gain from VIN to the receiving end of the
cable, VOUT, is set to –1. The effective impedance looking
into the amplifier circuit from the cable is 50Ω throughout
the usable bandwidth.
Driving back-terminated cables on single supplies usually
results in very limited signal amplitude at the receiving
end of the cable. However, positive feedback can be used
to reduce the size of the series back termination resistor,
thereby decreasing the attenuation between the series
and shunt termination resistors while still maintaining
controlled output impedance from the line-driving amplifier.
Figure 3 shows the LT6210 using this “active termination”
scheme on a single 3V supply. The amplifier is AC-coupled
and in an inverting gain configuration to maximize the input
The response of the cable driver with a 1MHz sinusoid is
shown in Figure 4. The circuit is capable of transmitting
a 1.5VP-P undistorted sinusoid to the 50Ω termination
resistor and has a full signal 1VP-P bandwidth of 50MHz.
Small signal –3dB bandwidth extends from 1kHz to 56MHz
with the selected coupling capacitors.
VIN
1V/DIV
3V
2k
1%
2k
1%
4
VIN
2.2µF 249Ω
1%
3
1.3k
1%
3V
6
+
1
LT6210
2
–
5
VA
1V/DIV
RSER
15Ω
1%
2.2µF
VOUT
RTERM
50Ω
VA
154Ω
1%
VOUT
1V/DIV
6210 F03
3300pF
NPO
200ns/DIV
6210 F04
Figure 4. Response of Circuit at 1MHz
Figure 3. 3V Cable Driver with Active Termination
Simplified Schematic
V+
6
V+
+IN
–IN
3
4
600Ω
600Ω
OUT
1
OUTPUT BIAS
CONTROL
V–
8k
V–
2
SUPPLY
CURRENT
CONTROL
5
ISET
6210 SS
62101fc
14
LT6210/LT6211
Package Description
DD Package
DD Package
10-Lead10-Lead
Plastic DFN
(3mm
× 3mm)
Plastic
DFN
(3mm × 3mm)
(Reference
LTC DWGLTC
# 05-08-1699
Rev C)
(Reference
DWG # 05-08-1699
Rev C)
0.70 ±0.05
3.55 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50
BSC
2.38 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.125
TYP
6
3.00 ±0.10
(4 SIDES)
0.40 ± 0.10
10
1.65 ± 0.10
(2 SIDES)
PIN 1 NOTCH
R = 0.20 OR
0.35 × 45°
CHAMFER
PIN 1
TOP MARK
(SEE NOTE 6)
0.200 REF
0.75 ±0.05
0.00 – 0.05
5
1
(DD) DFN REV C 0310
0.25 ± 0.05
0.50 BSC
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
62101fc
15
LT6210/LT6211
Package Description
MS Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1661 Rev E)
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.889 ± 0.127
(.035 ± .005)
5.23
(.206)
MIN
0.254
(.010)
3.20 – 3.45
(.126 – .136)
0.497 ± 0.076
(.0196 ± .003)
REF
10 9 8 7 6
DETAIL “A”
3.00 ± 0.102
(.118 ± .004)
(NOTE 4)
4.90 ± 0.152
(.193 ± .006)
0° – 6° TYP
GAUGE PLANE
0.50
0.305 ± 0.038
(.0197)
(.0120 ± .0015)
BSC
TYP
RECOMMENDED SOLDER PAD LAYOUT
0.53 ± 0.152
(.021 ± .006)
1 2 3 4 5
0.86
(.034)
REF
1.10
(.043)
MAX
DETAIL “A”
0.18
(.007)
SEATING
PLANE
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
0.1016 ± 0.0508
(.004 ± .002)
MSOP (MS) 0307 REV E
S6 Package
6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
0.62
MAX
2.90 BSC
(NOTE 4)
0.95
REF
1.22 REF
3.85 MAX 2.62 REF
1.4 MIN
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45
6 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
0.09 – 0.20
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
1.90 BSC
S6 TSOT-23 0302 REV B
62101fc
16
LT6210/LT6211
Revision History
(Revision history begins at Rev C)
REV
DATE
DESCRIPTION
C
3/11
Revised the tape and reel part numbers and temperature ranges in the Order Information section.
PAGE NUMBER
2
62101fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
17
LT6210/LT6211
Typical Application
Line Driver with Power Saving Mode
In applications where low distortion or high slew rate are
desirable but not necessary at all times, it may be possible
to decrease the LT6210 or LT6211’s quiescent current when
the higher power performance is not required. Figure 5
illustrates a method of setting quiescent current with a
FET switch. In the 5V dual supply case pictured, shorting
the ISET pin through an effective 20k to ground sets the
supply current to 6mA, while the 240k resistor at the ISET
pin with the FET turned off sets the supply current to approximately 1mA. The feedback resistor of 4.02k is selected
to minimize peaking in low power mode. The bandwidth
of the LT6210 in this circuit increases from about 40MHz
in low power mode to over 200MHz in full speed mode,
as illustrated in Figure 6. Other AC specs also improve
significantly at the higher current setting. The following
table shows harmonic distortion at 1MHz with a 2VP-P
sinusoid at the two selected current levels.
Harmonic Distortion
LOW POWER
FULL SPEED
HD2
–53dBc
HD2
–68dBc
HD3
–46dBc
HD3
–77dBc
3
R3
4.02k
2
5V
FULL
SPEED
MODE
IS = 6mA
4
VIN
3
–
6
LT6210
+
R2
22k
RLOAD
150Ω
2
5
HS/LP
1
VOUT
–5V
AMPLITUDE (dB)
1
0
–1
LOW POWER
MODE
IS = 1mA
–2
–3
–4
R1
240k
TA = 25°C
VOUT = 100mVP-P
–5
2N7002
–6
6210 F05
Figure 5. Line Driver with Low Power Mode
0
1
10
100
FREQUENCY (MHz)
1000
6210 F06
Figure 6. Frequency Response for Full
Speed and Low Power Mode
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LT1252/LT1253/LT1254
100MHz Low Cost Video Amplifiers
Single, Dual and Quad Current Feedback Amplifiers
LT1395/LT1396/LT1397
400MHz, 800V/µs Amplifiers
Single, Dual and Quad Current Feedback Amplifiers
LT1398/LT1399
300MHz Amplifiers with Shutdown
Dual and Triple Current Feedback Amplifiers
LT1795
50MHz, 500mA Programmable IS Amplifier
Dual Current Feedback Amplifier
LT1806/LT1807
325MHz, 140V/µs Rail-to-Rail I/O Amplifiers
Single and Dual Voltage Feedback Amplifiers
LT1815/LT1816/LT1817
220MHz, 1500V/µs Programmable IS Operational Amplifier
Single, Dual and Quad Voltage Feedback Amplifiers
62101fc
18 Linear Technology Corporation
LT 0311 REV C • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2003