LT4356-1 Overvoltage Protection Regulator and Inrush Limiter FEATURES DESCRIPTION n The LT®4356-1 surge stopper protects loads from high voltage transients. It regulates the output during an overvoltage event, such as load dump in automobiles, by controlling the gate of an external N-Channel MOSFET. The output is limited to a safe value thereby allowing the loads to continue functioning. The LT4356-1 also monitors the voltage drop between the VCC and SNS pins to protect against overcurrent faults. An internal amplifier limits the current sense voltage to 50mV. In either fault condition, a timer is started inversely proportional to MOSFET stress. If the timer expires, the FLT pin pulls low to warn of an impending power down. If the condition persists, the MOSFET is turned off. n n n n n n n n n n n Stops High Voltage Surges Adjustable Output Clamp Voltage Overcurrent Protection Wide Operation Range: 4V to 80V Reverse Input Protection to –60V Low 7μA Shutdown Current Adjustable Fault Timer Controls N-Channel MOSFET Shutdown Pin Withstands –60V to 100V Fault Output Indication Spare Amplifier for Level Detection Comparator or Linear Regulator Controller Available in (4mm × 3mm) 12-Pin DFN or 10-Pin MSOP Packages APPLICATIONS n n n Automotive/Avionic Surge Protection Hot Swap/Live Insertion High Side Switch for Battery Powered Systems L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. The spare amplifier may be used as a voltage detection comparator or as a linear regulator controller driving an external PNP pass transistor. Back-to-back FETs can be used in lieu of a Schottky diode for reverse input protection, reducing voltage drop and power loss. A shutdown pin reduces the quiescent current to less than 7μA during shutdown. TYPICAL APPLICATION 4A, 12V Overvoltage Output Regulator 10mΩ VIN 12V VOUT IRLR2908 80V INPUT SURGE 10Ω 383k Overvoltage Protector Regulates Output at 27V During Transient VCC SNS GATE 102k VIN 20V/DIV OUT FB SHDN IN+ 4.99k DC-DC CONVERTER LT4356DE-1 100k SHDN GND EN UNDERVOLTAGE AOUT GND TMR VCC FLT FAULT 12V 27V CLAMP VOUT 20V/DIV 12V 100ms/DIV 43561 TA01b 43561 TA01 0.1μF 43561fd 1 LT4356-1 ABSOLUTE MAXIMUM RATINGS (Notes 1 and 2) VCC , SHDN ................................................ –60V to 100V SNS..............................VCC –30V or –60V to VCC + 0.3V OUT, AOUT, FLT, EN .....................................– 0.3V to 80V GATE (Note 3) ................................ – 0.3V to VOUT + 10V FB, TMR, IN+ ................................................– 0.3V to 6V AOUT, EN, FLT .........................................................–3mA Operating Temperature Range LT4356C-1 ............................................... 0°C to 70°C LT4356I-1 ............................................–40°C to 85°C LT4356H-1 .........................................–40°C to 125°C Storage Temperature Range DE12 ..................................................–65°C to 125°C MS .....................................................–65°C to 150°C Lead Temperature (Soldering, 10 sec, MS10) ....... 300°C PIN CONFIGURATION TOP VIEW TMR 1 12 IN+ FB 2 11 AOUT 10 GND OUT 3 GATE 4 9 EN SNS 5 8 FLT VCC 6 7 SHDN 13 TOP VIEW FB OUT GATE SNS VCC DE PACKAGE 12-LEAD (4mm s 3mm) PLASTIC DFN TJMAX = 125°C, θJA = 43°C/W EXPOSED PAD (PIN 13) PCB GND CONNECTION OPTIONAL 1 2 3 4 5 10 9 8 7 6 TMR GND EN FLT SHDN MS PACKAGE 10-LEAD PLASTIC MSOP TJMAX = 125°C, θJA = 120°C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT4356CDE-1#PBF LT4356CDE-1#TRPBF 43561 12-Lead (4mm × 3mm) Plastic DFN 0°C to 70°C LT4356IDE-1#PBF LT4356IDE-1#TRPBF 43561 12-Lead (4mm × 3mm) Plastic DFN –40°C to 85°C LT4356HDE-1#PBF LT4356HDE-1#TRPBF 43561 12-Lead (4mm × 3mm) Plastic DFN –40°C to 125°C LT4356CMS-1#PBF LT4356CMS-1#TRPBF LTCNS 10-Lead Plastic MSOP 0°C to 70°C LT4356IMS-1#PBF LT4356IMS-1#TRPBF LTCNS 10-Lead Plastic MSOP –40°C to 85°C LT4356HMS-1#PBF LT4356HMS-1#TRPBF LTCNS 10-Lead Plastic MSOP –40°C to 125°C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT4356CDE-1 LT4356CDE-1#TR 43561 12-Lead (4mm × 3mm) Plastic DFN 0°C to 70°C LT4356IDE-1 LT4356IDE-1#TR 43561 12-Lead (4mm × 3mm) Plastic DFN –40°C to 85°C LT4356HDE-1 LT4356HDE-1#TR 43561 12-Lead (4mm × 3mm) Plastic DFN –40°C to 125°C LT4356CMS-1 LT4356CMS-1#TR LTCNS 10-Lead Plastic MSOP 0°C to 70°C LT4356IMS-1 LT4356IMS-1#TR LTCNS 10-Lead Plastic MSOP –40°C to 85°C LT4356HMS-1 LT4356HMS-1#TR LTCNS 10-Lead Plastic MSOP –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 43561fd 2 LT4356-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = 12V unless otherwise noted. SYMBOL VCC PARAMETER Operating Voltage Range ICC VCC Supply Current CONDITIONS l MIN 4 l VSHDN = FLOAT VSHDN = 0V LT4356I-1, LT4356C-1 LT4356H-1 VSNS = VCC = –30V, SHDN Open VSNS = VCC = VSHDN = –30V l l l l TYP MAX 80 1 1.5 mA 7 7 7 0.3 0.8 25 30 40 1 2 μA μA μA mA mA 8 18 V V –36 –50 μA μA IR Reverse Input Current ΔVGATE GATE Pin Output High Voltage VCC = 4V; (VGATE – VOUT) 48V ≥ VCC ≥ 8V; (VGATE – VOUT) l l 4.5 10 IGATE,UP GATE Pin Pull-Up Current VGATE = 12V; VCC = 12V VGATE = 48V; VCC = 48V l l –4 –4.5 –23 –30 IGATE,DN GATE Pin Pull-Down Current Overvoltage, VFB = 1.4V, VGATE = 12V Overcurrent, VCC – VSNS = 120mV, VGATE = 12V Shutdown Mode, VSHDN = 0V, VGATE = 12V l l l 75 5 1.5 150 10 5 VFB FB Pin Servo Voltage VGATE = 12V; VOUT = 12V, LT4356I-1, LT4356C-1 VGATE = 12V; VOUT = 12V, LT4356H-1 l l 1.225 1.215 1.25 1.25 UNITS V mA mA mA 1.275 1.275 V V IFB FB Pin Input Current VFB = 1.25V l 0.3 1 μA ΔVSNS Overcurrent Fault Threshold ΔVSNS = (VCC – VSNS), VCC = 12V, LT4356I-1, LT4356C-1 ΔVSNS = (VCC – VSNS), VCC = 12V, LT4356H-1 ΔVSNS = (VCC – VSNS), VCC = 48V, LT4356I-1, LT4356C-1 ΔVSNS = (VCC – VSNS), VCC = 48V, LT4356H-1 l l l l 45 42.5 46 43 50 50 51 51 55 55 56 56 mV mV mV mV ISNS SNS Pin Input Current VSNS = VCC = 12V to 48V l 5 10 22 μA ILEAK FLT, EN = 80V AOUT = 80V VTMR = 1V, VFB = 1.5V, (VCC – VOUT) = 0.5V VTMR = 1V, VFB = 1.5V, (VCC – VOUT) = 75V VTMR = 1.3V, VFB = 1.5V VTMR = 1V, ΔVSNS = 60mV, (VCC – VOUT) = 0.5V VTMR = 1V, ΔVSNS = 60mV, (VCC – VOUT) = 80V l ITMR FLT, EN Pins Leakage Current AOUT Pin Leakage Current TMR Pin Pull-up Current –2.5 –50 –5.5 –4.5 –260 2.5 4.5 –4 –55 –8 –6.5 –315 μA μA μA μA μA μA μA TMR Pin Pull-down Current VTMR = 1V, VFB = 1V, ΔVSNS = 0V l 1.7 2.2 2.7 μA VTMR TMR Pin Thresholds FLT From High to Low, VCC = 5V to 80V VGATE From Low to High, VCC = 5V to 80V l l 1.22 0.48 1.25 0.5 1.28 0.52 V V ΔVTMR Early Warning Period From FLT going Low to GATE going Low, VCC = 5V to 80V l 80 100 120 mV VIN+ IN+ Pin Threshold l 1.22 1.25 1.28 V l l l l l –1.5 –44 –3.5 –2.5 –195 IIN IN+ Pin Input Current VIN l 0.3 1 μA VOL FLT, EN, AOUT Pins Output Low ISINK = 2mA ISINK = 0.1mA l l 2 300 8 800 V mV IOUT OUT Pin Input Current VOUT = VCC = 12V VOUT = VCC = 12V, VSHDN = 0V l l 200 6 300 12 μA mA ΔVOUT OUT Pin High Threshold ΔVOUT = VCC – VOUT; EN From Low to High l 0.25 0.5 0.7 V VSHDN SHDN Pin Threshold VCC = 12V to 48V l 0.6 0.4 1.4 1.7 2.1 V V 1.7 2.2 V –4 –8 μA + VSHDN(FLT) SHDN Pin Float Voltage + = 1.25V VCC = 12V to 48V l VSHDN = 0V l Overcurrent Turn Off Delay Time GATE From High to Low, ΔVSNS = 0 → 120mV l 2 4 μs Overvoltage Turn Off Delay Time GATE From High to Low, VFB = 0 → 1.5V l 0.25 1 μs ISHDN SHDN Pin Current tOFF(OC) tOFF(OV) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device –1 pins are negative. All voltages are referenced to GND unless otherwise specified. Note 3: An internal clamp limits the GATE pin to a minimum of 10V above the OUT pin. Driving this pin to voltages beyond the clamp may damage the device. 43561fd 3 LT4356-1 TYPICAL PERFORMANCE CHARACTERISTICS Specifications are at VCC = 12V, TA = 25°C unless otherwise noted. ICC (Shutdown) vs VCC ICC vs VCC 60 ICC (Shutdown) vs Temperature 35 1000 30 50 800 25 30 600 ICC (μA) ICC (μA) ICC (μA) 40 400 20 15 20 10 200 10 5 0 0 10 20 30 40 50 VCC (V) 60 70 0 10 20 43561 G01 Reverse Current vs Reverse Voltage –20 0 –50 0 80 30 40 50 VCC (V) 60 70 80 VCC = SNS 125 GATE Pull-Up Current vs VCC 40 VSHDN = 0V 35 –15 30 –10 IGATE (μA) ISHDN (μA) 4 ICC (mA) 100 43561 G19 5 3 25 20 15 2 –5 10 1 0 25 75 0 50 TEMPERATURE (°C) 43561 G02 SHDN Current vs Temperature 6 –25 0 –20 –40 –60 5 0 –50 –80 –25 VCC (V) 25 75 0 50 TEMPERATURE (°C) 100 0 125 0 10 43561 G04 20 30 40 50 VCC (V) 60 70 80 43561 G05 43561 G03 GATE Pull-Up Current vs Temperature 35 GATE Pull-Down Current vs Temperature 220 VGATE = VOUT = 12V 30 20 15 10 180 160 140 120 5 –25 0 50 25 75 TEMPERATURE (°C) 100 125 43561 G06 100 –50 OVERCURRENT CONDITION ΔVSNS = 120mV 10 IGATE(DOWN) (mA) IGATE(DOWN) (mA) IGATE (μA) 12 OVERVOLTAGE CONDITION VFB = 1.5V 200 25 0 –50 GATE Pull-Down Current vs Temperature 8 6 4 2 –25 25 75 0 50 TEMPERATURE (°C) 100 125 43561 G07 0 –50 –25 25 75 0 50 TEMPERATURE (°C) 100 125 43561 G08 43561fd 4 LT4356-1 TYPICAL PERFORMANCE CHARACTERISTICS unless otherwise noted. ΔVGATE vs IGATE ΔVGATE vs Temperature 14 12 12 10 10 8 6 2 2 6 4 10 IGATE (μA) 8 12 14 VCC = 4V 4 2 0 50 25 75 TEMPERATURE (°C) 100 125 0 8 160 120 80 40 2 10 20 30 40 50 VCC – VOUT (V) 60 70 80 70 80 43561 G11 0 0 10 20 30 43561 G13 43561 G12 TMR Pull-Down Current vs Temperature 3.0 60 6 4 0 40 50 VCC (V) 8 80 0 0 70 30 OVERVOLTAGE, EARLY WARNING PERIOD 12 VFB = 1.5V VTMR = 1.3V 10 ITMR (μA) ITMR (μA) 16 60 20 14 200 30 40 50 VCC – VOUT (V) 10 Warning Period TMR Current vs VCC OVERCURRENT CONDITION VOUT = 0V 240 VTMR = 1V 32 40 50 VCC (V) 60 70 80 43561 G14 Output Low Voltage vs Current 4.0 VTMR = 1V 3.5 2.5 AOUT 3.0 2.0 2.5 VOL (V) ITMR (μA) 20 IGATE = –1μA VOUT = VCC 0 –25 280 OVERVOLTAGE CONDITION VOUT = 5V 40 VTMR = 1V 10 6 4356 G10 48 0 TA = –40°C 8 Overcurrent TMR Current vs (VCC – VOUT) 24 TA = 0°C 10 43561 G09 Overvoltage TMR Current vs (VCC – VOUT) ITMR (μA) VCC = 8V 0 –50 16 TA = 25°C 12 6 4 2 IGATE = –1μA 8 4 0 ΔVGATE vs VCC 14 ΔVGATE (V) VOUT = 12V ΔVGATE (V) ΔVGATE (V) 14 0 Specifications are at VCC = 12V, TA = 25°C 1.5 FLT 2.0 EN 1.5 1.0 1.0 0.5 0 –50 0.5 –25 0 25 50 75 TEMPERATURE (°C) 100 125 43561 G15 0 0 0.5 2.0 1.0 1.5 CURRENT (mA) 2.5 3.0 43561 G16 43561fd 5 LT4356-1 TYPICAL PERFORMANCE CHARACTERISTICS unless otherwise noted. Overvoltage Turn-Off Time vs Temperature 500 Specifications are at VCC = 12V, TA = 25°C Overcurrent Turn-Off Time vs Temperature 4.0 OVERVOLTAGE CONDITION VFB = 1.5V OVERCURRENT CONDITION ΔVSNS = 120mV 3.5 400 tOFF (μs) tOFF (ns) 3.0 300 200 2.5 2.0 100 0 –50 1.5 –25 0 25 50 75 TEMPERATURE (°C) 100 125 43561 G17 PIN FUNCTIONS 1.0 –50 –25 0 25 50 75 TEMPERATURE (°C) 100 125 43561 G18 (DE/MS) AOUT (Pin 11 DE Only): Amplifier Output. Open collector output of the auxiliary amplifier. It is capable of sinking up to 2mA from 80V. The negative input of the amplifier is internally connected to a 1.25V reference. EN (Pin 9/Pin 8): Open-Collector Enable Output. The EN pin goes high impedance when the voltage at the OUT pin is above (VCC – 0.7V), indicating the external MOSFET is fully on. The state of the pin is latched until the OUT pin voltage resets at below 0.5V and goes back up above 2V. The internal NPN is capable of sinking up to 3mA of current from 80V to drive an LED or opto-coupler. Exposed Pad (Pin 13 DE Only): Exposed pad may be left open or connected to device ground (GND). FB (Pin 2/Pin 1): Voltage Regulator Feedback Input. Connect this pin to the center tap of the output resistive divider connected between the OUT pin and ground. During an overvoltage condition, the GATE pin is servoed to maintain a 1.25V threshold at the FB pin. This pin is clamped internally to 7V. Tie to GND to disable the OV clamp. FLT (Pin 8/Pin 7): Open-Collector Fault Output. This pin pulls low after the voltage at the TMR pin has reached the fault threshold of 1.25V. It indicates the pass transistor is about to turn off because either the supply voltage has stayed at an elevated level for an extended period of time (voltage fault) or the device is in an overcurrent condition (current fault). The internal NPN is capable of sinking up to 3mA of current from 80V to drive an LED or opto-coupler. GATE (Pin 4/Pin 3): N-Channel MOSFET Gate Drive Output. The GATE pin is pulled up by an internal charge pump current source and clamped to 14V above the OUT pin. Both voltage and current amplifiers control the GATE pin to regulate the output voltage and limit the current through the MOSFET. GND (Pin 10/Pin 9): Device Ground. IN+ (Pin 12 DE Only): Positive Input of the Auxiliary Amplifier. This amplifier can be used as a level detection comparator with external hysteresis or linear regulator controlling an external PNP transistor. This pin is clamped internally to 7V. Connect to ground if unused. OUT (Pin 3/Pin 2): Output Voltage Sense Input. This pin senses the voltage at the source of the N-channel MOSFET and sets the fault timer current. When the OUT pin voltage reaches 0.7V away from VCC , the EN pin goes high impedance. SHDN (Pin 7/Pin 6): Shutdown Control Input. The LT4356-1 can be shutdown to a low current mode by pulling the SHDN pin below the shutdown threshold of 0.6V. Pull this pin above 1.7V or disconnect it and allow the inter43561fd 6 LT4356-1 nal current source to turn the part back on. The leakage current to ground at the pin should be limited to no more than 1μA if no pull up device is used to turn the part on. The SHDN pin can be pulled up to 100V or below GND by 60V without damage. charging up this pin during fault conditions depends on the voltage difference between the VCC and OUT pins. When VTMR reaches 1.25V, the FLT pin pulls low to indicate the detection of a fault condition. If the condition persists, the pass transistor turns off when VTMR reaches the threshold of 1.35V. The pull up current stops and a 2μA current source starts to pull the TMR pin down as soon as the fault condition disappears. When VTMR reaches the retry threshold of 0.5V, the GATE pin pulls high turning back on the pass transistor. SNS (Pin 5/Pin 4): Current Sense Input. Connect this pin to the output of the current sense resistor. The current limit circuit controls the GATE pin to limit the sense voltage between VCC and SNS pins to 50mV. At the same time the sense amplifier also starts a current source to charge up the TMR pin. This pin can be pulled below GND by up to 60V, though the voltage difference with the VCC pin must be limited to less than 30V. Connect to VCC if unused. VCC (Pin 6/Pin 5): Positive Supply Voltage Input. The positive supply input ranges from 4V to 80V for normal operation. It can also be pulled below ground potential by up to 60V during a reverse battery condition, without damaging the part. The supply current is reduced to 7μA with all the functional blocks off. TMR (Pin 1/Pin 10): Fault Timer Input. Connect a capacitor between this pin and ground to set the times for early warning, fault and cool down periods. The current BLOCK DIAGRAM VCC GATE + – 14V CHARGE PUMP + OUT FB + 50mV SNS – VA IA 1.25V – SHDN FLT AOUT OC 1.25V AUXILLARY AMPLIFIER SHDN RESTART OUT OV EN CONTROL LOGIC GATEOFF FLT – + IN+ 1.35V – VCC + 0.5V + ITMR – + 2μA 1.25V TMR – GND 43561 BD 43561fd 7 LT4356-1 OPERATION Some power systems must cope with high voltage surges of short duration such as those in automobiles. Load circuitry must be protected from these transients, yet high availability systems must continue operating during these events. The potential at the TMR pin starts decreasing as soon as the overvoltage condition disappears. When the voltage at the TMR pin reaches 0.5V the GATE pin begins rising, turning on the MOSFET. The FLT pin will then go to a high impedance state. The LT4356-1 is an overvoltage protection regulator that drives an external N-channel MOSFET as the pass transistor. It operates from a wide supply voltage range of 4V to 80V. It can also be pulled below ground potential by up to 60V without damage. The low power supply requirement of 4V allows it to operate even during cold cranking conditions in automotive applications. The internal charge pump turns on the N-channel MOSFET to supply current to the loads with very little power loss. Two MOSFETs can be connected back to back to replace an inline Schottky diode for reverse input protection. This improves the efficiency and increases the available supply voltage level to the load circuitry during cold crank. The fault timer allows the loads to continue functioning during short transient events while protecting the MOSFET from being damaged by a long period of supply overvoltage, such as a load dump in automobiles. The timer period varies with the voltage across the MOSFET. A higher voltage corresponds to a shorter fault timer period, ensuring the MOSFET operates within its safe operating area (SOA). Normally, the pass transistor is fully on, powering the loads with very little voltage drop. When the supply voltage surges too high, the voltage amplifier (VA) controls the gate of the MOSFET and regulates the voltage at the source pin to a level that is set by the external resistor divider from the OUT pin to ground and the internal 1.25V reference. A current source starts charging up the capacitor connected at the TMR pin to ground. If the voltage at the TMR pin, VTMR, reaches 1.25V, the FLT pin pulls low to indicate impending turn-off due to the overvoltage condition. The pass transistor stays on until the TMR pin reaches 1.35V, at which point the GATE pin pulls low turning off the MOSFET. The LT4356-1 senses an overcurrent condition by monitoring the voltage across an optional sense resistor placed between the VCC and SNS pins. An active current limit circuit (IA) controls the GATE pin to limit the sense voltage to 50mV. A current is also generated to start charging up the TMR pin. This current is about 5 times the current generated during an overvoltage event. The FLT pin pulls low when the voltage at the TMR pin reaches 1.25V and the MOSFET is turned off when it reaches 1.35V. A spare amplifier (SA) is provided with the negative input connected to an internal 1.25V reference. The output pull down device is capable of sinking up to 2mA of current allowing it to drive an LED or opto coupler. This amplifier can be configured as a linear regulator controller driving an external PNP transistor or a comparator function to monitor voltages. A shutdown pin turns off the pass transistor and reduces the supply current to less than 7μA. 43561fd 8 LT4356-1 APPLICATIONS INFORMATION The LT4356-1 can limit the voltage and current to the load circuitry during supply transients or overcurrent events. The total fault timer period should be set to ride through short overvoltage transients while not causing damage to the pass transistor. The selection of this N-channel MOSFET pass transistor is critical for this application. It must stay on and provide a low impedance path from the input supply to the load during normal operation and then dissipate power during overvoltage or overcurrent conditions. The following sections describe the overcurrent and the overvoltage faults, and the selection of the timer capacitor value based on the required warning time. The selection of the N-channel MOSFET pass transistor is discussed next. Auxiliary amplifier, reverse input, and the shutdown functions are covered after the MOSFET selection. External component selection is discussed in detail in the Design Example section. Overvoltage Fault The LTC4356-1 limits the voltage at the OUT pin during an overvoltage situation. An internal voltage amplifier regulates the GATE pin voltage to maintain a 1.25V threshold at the FB pin. During this period of time, the power MOSFET is still on and continues to supply current to the load. This allows uninterrupted operation during short overvoltage transient events. When the voltage regulation loop is engaged for longer than the time-out period, set by the timer capacitor connected from the TMR pin to ground, an overvoltage fault is detected. The GATE pin is pulled down to the OUT pin by a 150mA current. After the fault condition has disappeared and a cool down period has transpired, the GATE pin starts to pull high again. This prevents the power MOSFET from being damaged during a long period of overvoltage, such as during load dump in automobiles. Overcurrent Fault The LT4356-1 features an adjustable current limit that protects against short circuits or excessive load current. During an overcurrent event, the GATE pin is regulated to limit the current sense voltage across the VCC and SNS pins to 50mV. An overcurrent fault occurs when the current limit circuitry has been engaged for longer than the time-out delay set by the timer capacitor. The GATE pin is then immediately pulled low by a 10mA current to GND turning off the MOSFET. After the fault condition has disappeared and a cool down period has transpired, the GATE pin is allowed to pull back up and turn on the pass transistor. Fault Timer The LT4356-1 includes an adjustable fault timer pin. Connecting a capacitor from the TMR pin to ground sets the delay timer period before the MOSFET is turned off. The same capacitor also sets the cool down period before the MOSFET is allowed to turn back on after the fault condition has disappeared. Once a fault condition, either overvoltage or overcurrent, is detected, a current source charges up the TMR pin. The current level varies depending on the voltage drop across the drain and source terminals of the power MOSFET(VDS), which is typically from the VCC pin to the OUT pin. This scheme takes better advantage of the available Safe Operating Area (SOA) of the MOSFET than would a fixed timer current. The timer function operates down to VCC = 5V across the whole temperature range. Fault Timer Current The timer current starts at around 2μA with 0.5V or less of VDS , increasing linearly to 50μA with 75V of VDS during an overvoltage fault (Figure 1). During an overcurrent fault, it starts at 4μA with 0.5V or less of VDS but increases to 260μA with 80V across the MOSFET (Figure 2). This arrangement allows the pass transistor to turn off faster during an overcurrent event, since more power is dissipated during this condition. Refer to the Typical Performance Characteristics section for the timer current at different VDS in both overvoltage and overcurrent events. When the voltage at the TMR pin, VTMR , reaches the 1.25V threshold, the FLT pin pulls low to indicate the detection of a fault condition and provide warning to the load of the impending power loss. In the case of an overvoltage fault, the timer current then switches to a fixed 5μA. 43561fd 9 LT4356-1 APPLICATIONS INFORMATION MOSFET. The TMR pin is then actively regulated to 0.5V until the next fault condition appears. The total cool down timer period is given by: VTMR(V) ITMR = 5μA ITMR = 5μA 1.35 1.25 VDS = 75V (ITMR = 50μA) tCOOL = VDS = 10V (ITMR = 8μA) CTMR • 0.85V 2µA MOSFET Selection 0.50 TIME tFLT = 15ms/μF tWARNING = 20ms/μF tFLT = 93.75ms/μF tWARNING = 20ms/μF TOTAL FAULT TIMER = tFLT + tWARNING 43561 F01 Figure 1. Overvoltage Fault Timer Current The maximum allowable drain-source voltage must be higher than the supply voltage. If the output is shorted to ground or during an overvoltage event, the full supply voltage will appear across the MOSFET. VTMR(V) 1.35 1.25 VDS = 80V (ITMR = 260μA) 0.50 tFLT = 2.88ms/μF VDS = 10V (ITMR = 35μA) TIME tWARNING = 0.38ms/μF tFLT = 21.43ms/μF TOTAL FAULT TIMER = tFLT + tWARNING tWARNING = 2.86ms/μF 43561 F02 Figure 2. Overcurrent Fault Timer Current The interval between FLT asserting low and the MOSFET turning off is given by: t WARNING = The LT4356-1 drives an N-channel MOSFET to conduct the load current. The important features of the MOSFET are on-resistance RDS(ON) , the maximum drain-source voltage V(BR)DSS , the threshold voltage, and the SOA. CTMR • 100mV 5µA This fixed early warning period allows the systems to perform necessary backup or house keeping functions before the power supply is cut off. After VTMR crosses the 1.35V threshold, the pass transistor turns off immediately. Note that during an overcurrent event, the timer current is not reduced to 5μA after VTMR has reached 1.25V threshold, since it would lengthen the overall fault timer period and cause more stress on the power MOSFET. As soon as the fault condition has disappeared, a 2μA current starts to discharge the timer capacitor to ground. When VTMR reaches the 0.5V threshold, the internal charge pump starts to pull the GATE pin high, turning on the The gate drive for the MOSFET is guaranteed to be more than 10V and less than 18V for those applications with VCC higher than 8V. This allows the use of standard threshold voltage N-channel MOSFETs. For systems with VCC less than 8V, a logic level MOSFET is required since the gate drive can be as low as 4.5V. The SOA of the MOSFET must encompass all fault conditions. In normal operation the pass transistor is fully on, dissipating very little power. But during either overvoltage or overcurrent faults, the GATE pin is servoed to regulate either the output voltage or the current through the MOSFET. Large current and high voltage drop across the MOSFET can coexist in these cases. The SOA curves of the MOSFET must be considered carefully along with the selection of the fault timer capacitor. Transient Stress in the MOSFET During an overvoltage event, the LT4356-1 drives a series pass MOSFET to regulate the output voltage at an acceptable level. The load circuitry may continue operating throughout this interval, but only at the expense of dissipation in the MOSFET pass device. MOSFET dissipation or stress is a function of the input voltage waveform, regulation voltage and load current. The MOSFET must be sized to survive this stress. Most transient event specifications use the model shown in Figure 3. The idealized waveform comprises a linear 43561fd 10 LT4356-1 APPLICATIONS INFORMATION VPK VPK T T VREG VIN VIN tr tr 43561 F04 43561 F03 Figure 3. Prototypical Transient Waveform ramp of rise time tr, reaching a peak voltage of VPK and exponentially decaying back to VIN with a time constant of t. A common automotive transient specification has constants of tr = 10μs, VPK = 80V and τ = 1ms. A surge condition known as “load dump” has constants of tr = 5ms, VPK = 60V and τ = 200ms. MOSFET stress is the result of power dissipated within the device. For long duration surges of 100ms or more, stress is increasingly dominated by heat transfer; this is a matter of device packaging and mounting, and heatsink thermal mass. For short duration transients of less than 100ms, MOSFET survival is increasingly a matter of safe operating area (SOA), an intrinsic property of the MOSFET. SOA quantifies the time required at any given condition of VDS and ID to raise the junction temperature of the MOSFET to its rated maximum. MOSFET SOA is expressed in units of watt-squared-seconds (P2t). This figure is essentially constant for intervals of less than 100ms for any given device type, and rises to infinity under DC operating conditions. Destruction mechanisms other than bulk die temperature distort the lines of an accurately drawn SOA graph so that P2t is not the same for all combinations of ID and VDS. In particular P2t tends to degrade as VDS approaches the maximum rating, rendering some devices useless for absorbing energy above a certain voltage. Calculating Transient Stress To select a MOSFET suitable for any given application, the SOA stress must be calculated for each input transient which shall not interrupt operation. It is then a simple matter to chose a device which has adequate SOA to survive the maximum calculated stress. P2t for a prototypical transient waveform is calculated as follows (Figure 4). Figure 4. Safe Operating Area Required to Survive Prototypical Transient Waveform Let a = VREG – VIN b = VPK – VIN (VIN = Nominal Input Voltage) Then 1 ( b – a )3 tr + b P 2 t = ILOAD2 3 1 2 b 2 2 2a ln + 3a + b 4ab a 2 Typically VREG ≈ VIN and τ >> tr simplyfying the above to P2 t = 1 2 ILOAD 2 ( VPK – VREG ) τ 2 (W 2s) For the transient conditions of VPK = 80V, VIN = 12V, VREG = 16V, tr = 10μs and τ = 1ms, and a load current of 3A, P2t is 16.7W2s—easily handled by a MOSFET in a D-pak package. The P2t of other transient waveshapes is evaluated by integrating the square of MOSFET power versus time. Calculating Short Circuit Stress SOA stress must also be calculated for short circuit conditions. Short circuit P2t is given by: P 2 t = (VIN • Δ VSNS / RSNS )2 • t TMR (W 2s) where, ΔVSNS is the SENSE pin threshold, and tTMR is the overcurrent timer interval. For VIN = 14.7V, VSNS = 50mV, RSNS = 12mΩ and CTMR = 100nF, P2t is 6.6W2s—less than the transient SOA calculated in the previous example. Nevertheless, to ac43561fd 11 LT4356-1 APPLICATIONS INFORMATION count for circuit tolerances this figure should be doubled to 13.2W2s. Limiting Inrush Current and GATE Pin Compensation The LT4356-1 limits the inrush current to any load capacitance by controlling the GATE pin voltage slew rate. An external capacitor can be connected from GATE to ground to slow down the inrush current further at the expense of slower turn-off time. The amplifier can also be configured as a low dropout linear regulator controller. With an external PNP transistor, such as 2N2905A, it can supply up to 100mA of current with only a few hundred mV of dropout voltage. Current limit can be easily included by adding two diodes and one resistor (Figure 6). *4.7Ω INPUT The LTC4356-1 does not need extra compensation components at the GATE pin for stability during an overvoltage or overcurrent event. However, with fast, high voltage transient steps at the input, a gate capacitor, C1, to ground is needed to prevent turn-on of the N-Channel MOSFET. R6 100k 2N2905A OR BCP53 OUTPUT * OPTIONAL FOR CURRENT LIMIT D1* BAV99 11 AOUT LT4356DE-1 43561 F06 The extra gate capacitance slows down the turn off time during fault conditions and may allow excessive current during an output short event. An extra resistor, R1, in series with the gate capacitor can improve the turn off time. A diode, D1, should be placed across R1 with the cathode connected to C1 as shown in Figure 5. Auxiliary Amplifier An uncommitted amplifier is included in the LT4356-1 to provide flexibility in the system design. With the negative input connected internally to the 1.25V reference, the amplifier can be connected as a level detect comparator with external hysteresis. The open collector output pin, AOUT, is capable of driving an opto or LED. It can also interface with the system via a pull-up resistor to a supply voltage up to 80V. Figure 6. Auxiliary LDO Output with Optional Current Limit Reverse Input Protection A blocking diode is commonly employed when reverse input potential is possible, such as in automotive applications. This diode causes extra power loss, generates heat, and reduces the available supply voltage range. During cold crank, the extra voltage drop across the diode is particularly undesirable. The LT4356-1 is designed to withstand reverse voltage without damage to itself or the load. The VCC , SNS, and SHDN pins can withstand up to 60V of DC voltage below the GND potential. Back-to-back MOSFETs must be used to eliminate the current path through their body diodes (Figure 7). Figure 8 shows the approach with a P-Channel MOSFET in place of Q2. Shutdown Q1 The LT4356-1 can be shut down to a low current mode when the voltage at the SHDN pin goes below the shutdown threshold of 0.6V. The quiescent current drops to 7μA. D1 IN4148W R3 R1 C1 GATE LT4356-1 43561 F05 Figure 5 The SHDN pin can be pulled up to VCC or below GND by up to 60V without damaging the pin. Leaving the pin open allows an internal current source to pull it up and turn on the part while clamping the pin to 2.5V. The leakage current at the pin should be limited to no more than 1μA if no pull up device is used to help turn it on. 43561fd 12 LT4356-1 APPLICATIONS INFORMATION RSNS 10mΩ VIN 12V Q2 IRLR2908 D2* SMAJ58CA R4 R5 10Ω 1M Q3 2N3904 C2 0.1μF R6 10Ω VOUT 12V, 3A CLAMPED AT 16V R3 10Ω R1 59k D1 1N4148 6 Q1 IRLR2908 R7 10k 5 SNS 4 GATE 3 OUT VCC FB A 1μF ceramic capacitor, CL, is needed at the OUT pin to clamp the voltage spike if the input voltage rise time is 2 R2 4.99k RSNS 10mΩ LT4356DE-1 7 11 12 VIN SHDN FLT AOUT IN+ GND EN TMR 10 1 *DIODES INC. RSNS 10mΩ Q2 Si4435 9 6 VOUT 12V, 3A CLAMPED AT 16V R3 10Ω 11 12 4 GATE 3 OUT FB VCC FLT AOUT IN+ EN TMR *DIODES INC. IN+ R2 4.99k LT4356DE-1 UNDERVOLTAGE EN 11 1 2 SHDN AOUT GND TMR 1 FLT 9 8 VCC DC-DC CONVERTER SHDN GND FAULT 43561 F09 CTMR 47nF 2 LT4356DE-1 10 FB CL 1μF CERAMIC Figure 9. Overvoltage Regulator with Low Battery Detection SHDN GND 12 VCC R1 59k R2 4.99k 7 7 R1 59k R3 10Ω 5 4 3 SNS GATE OUT 10 5 SNS 6 R4 383k Q1 IRLR2908 R5 100k Q1 IRLR2908 R6 10k C2 0.1μF R6 10Ω 43561 F07 CTMR 0.1μF D1 1N5245 15V D2* SMAJ58CA C2 0.1μF 100V D2 SMAJ58A 8 Figure 7. Overvoltage Regulator with N-Channel MOSFET Reverse Input Protection VIN 12V power trace parasitic inductance should be minimized by using wide traces. A snubber circuit dampens the ringing associated with voltage spikes. A 10Ω resistor in series with a 0.1μF capacitor between VCC and GND is effective with up to 1μH feed point inductance. A surge suppressor, D2, in Figure 9, at the input will clamp the voltage spikes. 8 9 43561 F08 CTMR 0.1μF Figure 8. Overvoltage Regulator with P-Channel MOSFET Reverse Input Protection Supply Transient Protection The LT4356-1 is 100% tested and guaranteed to be safe from damage with supply voltages up to 80V. Nevertheless, voltage transients above 100V may cause permanent damage. During a short-circuit condition, the large change in current flowing through power supply traces and associated wiring can cause inductive voltage transients which could exceed 100V. To minimize the voltage transients, the faster than 10μs. A total bulk capacitance in the range of 22μF is also required close to the VCC pin of the DC/DC converter, if not already provided by the converter. Layout Considerations To achieve accurate current sensing, Kelvin connection to the current sense resistor (RSNS in Figure 9) is recommended. The minimum trace width for 1oz copper foil is 0.02" per amp to ensure the trace stays at a reasonable temperature. 0.03" per amp or wider is recommended. Note that 1oz copper exhibits a sheet resistance of about 530μΩ/square. Small resistances can cause large errors in high current applications. Noise immunity will be improved significantly by locating resistive dividers close to the pins with short VCC and GND traces. 43561fd 13 LT4356-1 APPLICATIONS INFORMATION Design Example CTMR is then chosen for 1ms of early warning time: As a design example, take an application with the following specifications: VCC = 8V to 14V DC with transient up to 80V, VOUT ≤ 16V, current limit (ILIM) at 5A, low battery detection at 6V, and 1ms of overvoltage early warning (Figure 9). First, calculate the resistive divider value to limit VOUT to 16V during an overvoltage event: 1.25V • (R1 + R2) VREG = = 16V R2 Set the current through R1 and R2 during the overvoltage condition to 250μA. R2 = 1.25V = 5k 250µA (16V – 1.25V ) • R2 1.25V The closest standard value for CTMR is 47nF. Finally, calculate R4 and R5 for the 6V low battery threshold detection: 6V = 1.25V • (R4 + R5) R5 Choose 100kΩ for R5. R4 = (6V – 1.25V ) • R5 1.25V = 380k The pass transistor, Q1, should be chosen to withstand the output short condition with VCC = 14V. = 58.88k The closest standard value for R1 is 59kΩ. Next calculate the sense resistor, RSNS, value: RSNS 1ms • 5µA = 50nF 100mV Select 383kΩ for R4. Choose 4.99kΩ for R2. R1 = CTMR = 50mV 50mV = = = 10m ILIM 5A The total overcurrent fault time is: tOC = 47nF • 0.85V = 0.878ms 45.5μA The power dissipation on Q1 equals to: P= 14V • 50mV = 70W 10m These conditions are well within the Safe Operating Area of IRLR2908. 43561fd 14 LT4356-1 TYPICAL APPLICATIONS 24V Overvoltage Regulator Withstands 150V at VIN VIN 24V Q1 IRF640 R9 1k 1W VOUT CLAMPED AT 32V R3 10Ω 5 SNS 6 4 GATE VCC FB D2* SMAT70A 2 R2 4.99k 7 SHDN 8 FLT 9 LT4356DE-1 EN GND 10 *DIODES INC. R1 118k 3 OUT TMR 1 43561 TA05 CTMR 0.1μF 43561fd 15 LT4356-1 TYPICAL APPLICATIONS Overvoltage Regulator with Low Battery Detection and Output Keep Alive During Shutdown 1k 0.5W RSNS 10mΩ VIN 12V D2* SMAJ58A Q1 IRLR2908 R3 10Ω R4 402k 6 C2 0.1μF R6 10Ω 12 R5 105k 7 5 SNS 4 GATE Q2 VN2222 3 OUT VCC FB AOUT SHDN FLT 10 EN TMR 1 R1 294k D1 1N4746A 18V 1W 2 R2 VDD 24.9k R6 47k LT4356DE-1 IN+ GND *DIODES INC. VOUT 12V, 4A C2 CLAMPED AT 16V 10μF 11 LBO 8 9 43561 TA03 CTMR 0.1μF 43561fd 16 LT4356-1 TYPICAL APPLICATIONS 2.5A, 48V Hot Swap with Overvoltage Output Regulation at 72V and UV Shutdown at 35V RSNS 15mΩ VIN 48V Q1 FDB3632 RS 100Ω CS 0.01μF D2* SMAT70A R4 140k R3 10Ω VOUT 48V 2.5A R6 27k CL 300μF C1 6.8nF D1 1N4714 BV = 33V 7 6 VCC 5 4 SNS GATE 3 OUT 12 IN+ SHDN R5 4.02k R8 47k LT4356DE-1 8 9 R7 1M FB R1 226k 2 R2 4.02k FLT EN GND AOUT TMR 10 1 *DIODES INC. 11 PWRGD 43561 TA06 CTMR 0.1μF 2.5A, 28V Hot Swap with Overvoltage Output Regulation at 36V and UV Shutdown at 15V RSNS 15mΩ VIN 28V Q1 FDB3632 RS 100Ω CS 0.01μF D2* SMAT70A R4 113k R3 10Ω VOUT 28V 2.5A R6 27k CL 300μF C1 6.8nF D1 1N4700 BV = 13V 7 6 VCC 5 4 SNS GATE 3 OUT 12 IN+ SHDN R5 4.02k R8 47k LT4356DE-1 8 9 2 R1 110k R2 4.02k GND 10 *DIODES INC. FB FLT EN R7 1M TMR 1 AOUT 11 PWRGD 43561 TA07 CTMR 0.1μF 43561fd 17 LT4356-1 PACKAGE DESCRIPTION DE/UE Package 12-Lead Plastic DFN (4mm × 3mm) (Reference LTC DWG # 05-08-1695 Rev C) 0.70 ±0.05 3.60 ±0.05 1.70 ±0.05 2.20 ±0.05 (2 SIDES) PACKAGE OUTLINE 0.25 ± 0.05 3.30 ±0.05 (2 SIDES) 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4.00 ±0.10 (2 SIDES) 7 R = 0.115 TYP 0.40 ± 0.10 12 R = 0.05 TYP PIN 1 TOP MARK (NOTE 6) 0.200 REF 3.00 ±0.10 (2 SIDES) 1.70 ± 0.05 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER 0.75 ±0.05 0.00 – 0.05 6 0.25 ± 0.05 3.30 ±0.05 (2 SIDES) 1 (UE12/DE12) DFN 0905 REV C 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE A VARIATION OF VERSION (WGED) IN JEDEC PACKAGE OUTLINE M0-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 43561fd 18 LT4356-1 PACKAGE DESCRIPTION MS Package 10-Lead Plastic MSOP (Reference LTC DWG # 05-08-1661) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 3.20 – 3.45 (.126 – .136) 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 0.50 0.305 ± 0.038 (.0197) (.0120 ± .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) 0.497 ± 0.076 (.0196 ± .003) REF 10 9 8 7 6 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 4.90 ± 0.152 (.193 ± .006) DETAIL “A” 0° – 6° TYP GAUGE PLANE 1 2 3 4 5 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 0.86 (.034) REF 1.10 (.043) MAX 0.18 (.007) SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP 0.50 (.0197) BSC 0.1016 ± 0.0508 (.004 ± .002) MSOP (MS) 0307 REV E NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 43561fd Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LT4356-1 TYPICAL APPLICATION Overvoltage Regulator with Linear Regulator Up to 100mA Q2 2N2905A 2.5V, 100mA RSNS 10mΩ VIN 12V Q1 IRLR2908 D2* SMAJ58A R6 100k 6 C2 0.1μF R6 10Ω C5 10μF VOUT 12V, 3A CLAMPED AT 16V R3 10Ω 4 GATE 5 SNS VCC R1 59k 3 OUT FB 2 R2 4.99k 11 7 LT4356DE-1 AOUT IN+ 12 SHDN FLT 8 GND 10 *DIODES INC. EN TMR 1 R4 249k C3 47nF R5 249k 9 43561 TA04 CTMR 0.1μF RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1641-1/LT1641-2 Positive High Voltage Hot Swap™ Controllers Active Current Limiting, Supplies From 9V to 80V LTC1696 Overvoltage Protection Controller ThinSOT™ Package, 2.7V to 28V LTC1735 High Efficiency Synchronous Step-Down Switching Regulator Output Fault Protection, 16-Pin SSOP LTC1778 No RSENSE™ Wide Input Range Synchronous Step-Down Controller Up to 97% Efficiency, 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ (0.9)(VIN), IOUT Up to 20A LTC2909 Triple/Dual Inputs UV/OV Negative Monitor Pin Selectable Input Polarity Allows Negative and OV Monitoring LTC2912/LTC2913 Single/Dual UV/OV Voltage Monitor Ads UV and OV Trip Values, ±1.5% Threshold Accuracy LTC2914 Quad UV/OV Monitor For Positive and Negative Supplies LTC3727/LTC3727-1 2-Phase, Dual, Synchronous Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 14V LTC3827/LTC3827-1 Low IQ, Dual, Synchronous Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, 80μA Quiescent Current LTC3835/LTC3835-1 Low IQ, Synchronous Step-Down Controller LT3845 Low IQ, Synchronous Step-Down Controller Single Channel LTC3827/LTC3827-1 LT3850 Dual, 550kHz, 2-Phase Sychronous Step-Down Controller Dual 180° Phased Controllers, VIN 4V to 24V, 97% Duty Cycle, 4mm × 4mm QFN-28, SSOP-28 Packages LT4256 Positive 48V Hot Swap Controller with Open-Circuit Detect Foldback Current Limiting, Open-Circuit and Overcurrent Fault Output, Up to 80V Supply LTC4260 Positive High Voltage Hot Swap Controller with ADC and I2C Wide Operating Range 8.5V to 80V LT4351 Ideal MOSFET ORing Diode External N-channel MOSFETs Replace ORing Diodes, 1.2V to 20V LTC4354 Negative Voltage Diode-OR Controller Controls Two N-Channel MOSFETs, 1μs Turn-Off, 80V Operation LTC4355 Positive Voltage Diode-OR Controller Controls Two N-Channel MOSFETs, 0.5μs Turn-Off, 80V Operation 4V ≤ VIN ≤ 60V, 1.23V ≤ VOUT ≤ 36V, 120μA Quiescent Current Hot Swap, No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. 43561fd 20 Linear Technology Corporation LT 0808 REV D • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007