LINER LTP5903-WHR

- ADVANCED INFORMATION -
SmartMesh® WirelessHARTTM
LTP5903-WHR
2.4 GHz 802.15.4 Embedded Network Manager
About SmartMesh WirelessHART
SmartMesh WirelessHART products are designed for the harshest industrial environments, where low power, reliability, resilience and
scalability are key. SmartMesh WirelessHART solutions are well-suited for applications requiring WirelessHART standards compliance, as
well as a wide range of applications from renewable energy generation, such as solar and wind power, to factory machine health
monitoring and data center HVAC energy management. Smartmesh WirelessHART complies with the WirelessHART (IEC 62591)
standard, offers the lowest power consumption in its class and is the most widely used WirelessHART product available. SmartMesh
WirelessHART systems are easy for industrial automation vendors to integrate and simple for end users to deploy.
Product Description— LTP5903-WHR
The LTP5903-WHR embedded network manager combines Dust Networks’ robust, Intelligent Networking Platform and industry-leading
low-power radio technology in an easy-to-integrate embedded subsystem. The LTP5903-WHR is designed for use in line-powered
gateways and controllers, such as WirelessHART Gateways, and enables customers to integrate a standards-based wireless sensor network
that provides scalable bidirectional communications. . The embedded network manager offers a comprehensive API to deliver rich and
flexible functionality without complex coding. This API also provides full visibility and control over network configuration, security
administration, network status, and performance statistics. The network-ready embedded manager enables industrial automation vendors to
integrate advanced wireless sensor networking intelligence into monitoring and control solutions with low risk and rapid time-to-market.
Key Product Features
LTP5903-WHR Datasheet
Dust Networks
IEEE 802.15.4 PHY
Encryption and Authentication
Fast and Low Risk Integration
•
Comprehensive APIs deliver rich and flexible
functionality without complex coding
•
Fully integrated and certified RF capabilities—simply add
an antenna
Secure Global Market Solution
•
IEEE 802.15.4-certified radio operates on 2.4 GHz global
license-free band
•
Configurable radio output—meets RF emission limits for
different regions with a single product
•
Modular RF certifications for FCC, IC, and CE (pending)
•
AES-128 bit encryption
RSSI
Intelligent Network Management
•
Dynamic network optimization maintains network health
and enables greater than 99.99% network reliability even
in the most challenging environments
•
Deterministic power management ensures system-wide
optimization to avoid early or frequent battery changes
•
Intelligent routing lowers latency, reduces network power
consumption and eliminates in-network collisions
•
Manages networks of up to 250 motes, with optional
software upgrade to 500 motes
Bandwidth Flexibility
•
Bandwidth flexibility accommodates the range of network
latency and throughput needs of monitoring and control
applications
•
Dynamic bandwidth assigns different levels of bandwidth on a
per-mote basis to satisfy unique device throughput requirements
WirelessHART
MAC
WirelessHART Compliance
•
Interoperable with WirelessHART field devices
1
- ADVANCED INFORMATION -
Table of Contents
1.0
Absolute Maximum Ratings ................................................................................4
2.0
Normal Operating Conditions .............................................................................4
3.0
Electrical Specifications .....................................................................................4
3.1
LVTTL I/O DC Specifications ................................................................................ 5
3.2
LED Specifications.............................................................................................. 5
3.3
3.3 V Output Supply........................................................................................... 6
3.4
Device Load ...................................................................................................... 6
3.5
AC Timing Specifications ..................................................................................... 6
4.0
Real-time Clock ..................................................................................................6
5.0
Radio..................................................................................................................6
5.1
Detailed Radio Specifications ............................................................................... 6
5.2
Antenna Specifications........................................................................................ 7
6.0
SmartMesh WirelessHART Intelligent Networking Platform ...............................8
6.1
Dynamic Network Optimization ............................................................................ 8
6.2
Deterministic Power Management......................................................................... 8
6.3
Intelligent Routing ............................................................................................. 8
6.4
Bandwidth Flexibility .......................................................................................... 8
7.0
Interfaces ..........................................................................................................8
7.1
Hardware Interfaces........................................................................................... 8
7.1.1
10/100Base-T Ethernet Interface ................................................................... 9
7.1.2
Serial 1 Interface......................................................................................... 9
7.1.3
Serial 2 Interface......................................................................................... 9
7.1.4
LED Status Indicators................................................................................... 9
7.1.5
Restore Signal............................................................................................. 9
7.2
Software Interfaces...........................................................................................11
7.2.1
XML API ....................................................................................................11
7.2.2
Admin Toolset ............................................................................................11
7.2.3
Command Line Interface..............................................................................11
8.0
Board-to-board Connectors ..............................................................................11
8.1
Connector Pin Numbering...................................................................................11
8.2
Pinout .............................................................................................................12
8.3
Recommended Mating Connectors .......................................................................14
9.0
Mechanical Specifications.................................................................................14
9.1
10.0
LTP5903-WHR Mechanical Drawings ....................................................................14
Regulatory and Standards Compliance .............................................................15
10.1 FCC Compliance ...............................................................................................15
10.1.1 FCC Testing ...............................................................................................15
10.1.2 FCC-approved Antenna................................................................................16
10.1.3 OEM Labeling Requirements .........................................................................16
10.2 IC Compliance ..................................................................................................16
2
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
10.2.1 IC Testing..................................................................................................16
10.2.2 IC-approved Antennae ................................................................................16
10.2.3 OEM Labeling Requirements .........................................................................16
10.3 CE Compliance .................................................................................................17
10.3.1 Declaration of Conformity ............................................................................17
10.3.2 European Compliance..................................................................................17
10.3.3 OEM Labeling Requirements .........................................................................17
10.3.4 Restrictions................................................................................................17
10.4 Compliance to Restriction of Hazardous Substances (RoHS) ....................................17
10.5 Industrial Environment Operation........................................................................18
11.0
Order Information............................................................................................18
12.0
Related Documentation ....................................................................................18
LTP5903-WHR Datasheet
Dust Networks
3
- ADVANCED INFORMATION -
1.0
Absolute Maximum Ratings
The absolute maximum ratings shown below should not be violated under any circumstances. Permanent damage to the
device may be caused by exceeding one or more of these parameters.
Table 1
Absolute Maximum Ratings
Parameter
Supply voltage (+5V_IN to GND)
Min
Typ
–0.3
Input RF level
Storage temperature range
–40
VSWR of antenna
Max
Units
6
V
10
dBm
+85
°C
Comments
Input power at antenna
connector
3:1
ESD protection
Antenna connector
±8000
V
HBM
All other connectors
±2
kV
HBM
±200
V
CDM
All voltages are referenced to GND
Caution! ESD sensitive device. Precaution should be used when handling the device in order to prevent
permanent damage.
2.0
Table 2
Normal Operating Conditions
Normal Operating Conditions
Parameter
Min
Typ
Max
Units
4.0
5.0
5.5
VDC
Including noise and load
regulation
Voltage supply noise
100
mVp-p
50 Hz–50 MHz
Peak current
350
mA
+3V3 out = 0 mA
150
mA
+5V_IN at 5.0 V, 25 °C,
+3V3 out = 0 mA
225
mA
+5V_IN at 5.0 V, 25 °C,
+3V3 out = 100 mA
Operational supply voltage range
(between +5V_IN and GND)
Comments
Average current
Operating temperature range
–40
Maximum allowed temperature
ramp during operation
Operating relative humidity
10
+85
°C
8
°C/min
–40 °C to +85 °C
90
% RH
Non-condensing
The specifications listed are for the power supply connected to +5V_IN and GND, and apply over the operating
temperature range unless otherwise specified.
3.0
Electrical Specifications
I/O specifications are given below for each I/O level type given in the board-to-board connector tables in sections 7.1 and 8.2. Unless
otherwise noted, +5V_IN is 5.0 V and temperature is –40 °C to +85 °C.
4
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
3.1
Table 3
LVTTL I/O DC Specifications
LVTTL Type 1 Specifications
Max
Units
VIH (logical high input)
Parameter
Min
2.0
Typ
3.6
V
VIL (logical low input)
-0.3
0.8
V
60
µA
0.4
V
IIN (input leakage)
VOH (logical high output)
2.6
V
VOL (logical low output)
IOH (VO = VOH) (source)
8
mA
IOL (VO = VOL) (sink)
8
mA
Table 4
LVTTL Type 2 Specifications (Schmitt Trigger)
Parameter
Min
Typ
Max
Units
V + Threshold
1.3
2.5
V
V – Threshold
0.6
1.6
V
±5
µA
Max
Units
IIN (input leakage)
Table 5
Min
VOH
Typ
2.6
0.4
V
IOH
-12
mA
IOL
12
mA
LVTTL Type 4 Specifications
Parameter
Min
Typ
Max
Units
V
VOH (logical high output)
2.6
+3V3
VOL (logical low output)
GND
0.4
IOH (VO = VOH) (source)
2
mA
IOL (VO = VOL) (sink)
2
mA
V
Min
Typ
Max
Units
V
VIH (logical high input)
2.6
+3V3 + 0.3
VIL (logical low input)
GND – 0.3
GND + 0.8
V
±5
µA
Max
Units
V
IIN (input leakage)
Table 8
Comments
LVTTL Type 5 Specifications
Parameter
3.2
Comments
V
VOL
Table 7
Comments
LVTTL Type 3 Specifications
Parameter
Table 6
Comments
Comments
LED Specifications
LED Specifications
Parameter
Min
Typ
Comments
VOH (logical high output)
+3V3 – 0.3
+3V3
VOL (logical low output)
GND
GND + 0.4
IOH (VO = VOH) (source)
3
mA
+3V3 = 3.3 V
IOL (VO = VOL), I/O = LED (sink)
1.5
mA
+3V3 = 3.3 V
IOL (VO = VOH), I/O = LED low (sink)
0.5
mA
+3V3 = 3.3 V
LTP5903-WHR Datasheet
Dust Networks
V
5
- ADVANCED INFORMATION -
3.3
3.3 V Output Supply
The LTP5903-WHR includes a regulated 3.3 V output signal (labeled +3V3) for supplying power to user circuitry (for
example, isolation or signal conditioning). Note that any power drawn on +3V3 circuitry results in an increase in power
drawn on +5V_IN.
Table 10 +3.3 V Power Supply Output
Parameter
Min
Typ
Max
Units
100
mA
3.46
V
Max
Units
Total capacitance
290
µF
Total inductance
8
µH
Max
Units
+3V3 current source
+3V3 supply voltage
3.4
3.13
Comments
Device Load
Table 11 Device Load
Parameter
3.5
Min
Typ
Comments
AC Timing Specifications
Table 12 AC Timing Specifications
Parameter
nRESET_IN pulse width
4.0
Min
Typ
125
Comments
µs
Real-time Clock
The LTP5903-WHR has a battery-backed real-time clock (RTC) with a typical lifetime of 5-7 years (lifetime up to 15 years if
the manager is normally powered), assuming the manager is operating at 60 °C average ambient temperature and at 10% duty
cycle. Upon bootup, the RTC initializes the software system clock that handles timekeeping while the system is operating.
The software system clock is the reference for UTC time values readable through the software APIs, command line interface
(CLI) and Admin Toolset Web interface, as well as the UTC time values visible in manager log files. The system clock may
be set manually using the Admin Toolset Web interface, or through the Linux command shell. The accuracy of the software
system clock is typically 1 min/month at 25°C, though may vary as much as 10 min/month at temperature extremes. To
support applications less tolerant of such drift, the LTP5903-WHR software includes an NTP client to periodically
synchronize software system time to an outside source. The NTP client is configurable using the Admin Toolset Web
interface, or through the Linux command shell.
5.0
Radio
5.1
Detailed Radio Specifications
Table 13 Radio Specifications
Parameter
Operating frequency
Min
2.4000
Number of channels
Max
Units
2.4835
GHz
Occupied channel bandwidth
5
MHz
2.7
MHz
-40
+40
Receiver operating input level
Receiver sensitivity
6
At –20 dBc
ppm
Modulation
Raw data rate
Comments
15
Channel separation
Frequency accuracy
Typ
IEEE 802.15.4 DSSS
250
Kbps
0
dBm
–92.5
dBm
At 50% PER, VDD = 3 V,
25 °C
–90
dBm
At 1% PER, VDD = 3 V,
25 °C, (inferred by 50% PER
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
Parameter
Min
Typ
Max
Units
Comments
measurement)
Output power, conducted
Power amplifier enabled:
At 25 °C
+8
dBm
–2
dBm
100
m
Power amplifier disabled:
At 25 °C
Range*
Power amplifier enabled:
Indoor†
Outdoor
†
300
m
1200
m
Indoor†
25
m
Outdoor†
200
m
Free Space
350
m
Free Space
25 °C, 50% RH, +2 dBi
omni-directional antenna
Power amplifier disabled:
25 °C, 50% RH, +2 dBi
omni-directional antenna
*Actual RF range performance is subject to a number of installation-specific variables including, but not restricted to
ambient temperature, relative humidity, presence of active interference sources, line-of-sight obstacles, near-presence
of objects (for example, trees, walls, signage, and so on) that may induce multipath fading. As a result, actual
performance varies for each instance.
†
1 meter above ground.
5.2
Antenna Specifications
A MMCX-compatible jack receptacle is provided on board for the antenna connection. For antenna location, refer to the
mechanical drawing in section 9.1. The antenna must meet specifications in Table 14. For a list of antennae pre-approved for
RF certification, see section 10.1.2.
Table 14 Antenna Specifications
Parameter
Value
Frequency range
Impedance
50 Ω
2.4–2.4835 GHz
Gain
LTP5903-WHR
Pattern
Maximum VSWR
Connector
+2 dBi maximum
Omni-directional
3:1
MMCX*
* The LTP5903-WHR can accommodate the following RF mating connectors:
• MMCX straight connector such as Johnson 135-3402-001, or equivalent
• MMCX right angle connector such as Tyco 1408149-1, or equivalent
When the LTP5903-WHR is placed inside an enclosure, the antenna should be mounted such that the radiating portion of the
antenna protrudes from the enclosure, and connected using a MMCX connector on a coaxial cable. For optimum
performance, allow the antenna to be positioned vertically when installed.
LTP5903-WHR Datasheet
Dust Networks
7
- ADVANCED INFORMATION -
6.0
SmartMesh WirelessHART Intelligent Networking
Platform
The SmartMesh WirelessHART LTP5903-WHR embedded network manager is built upon Dust Networks’ Intelligent
Networking Platform, which provides dynamic network optimization, deterministic power management, intelligent routing,
and bandwidth flexibility to achieve the carrier class data reliability, and ultra-low power and ease of use required for
industrial automation applications.
6.1
Dynamic Network Optimization
Dynamic network optimization allows the LTP5903-WHR to address the changing RF requirements in harsh industrial
environments resulting in a network that is continuously self-monitoring and self-adjusting. The LTP5903-WHR manager
performs dynamic network optimization based upon periodic reports on network health and link quality that it receives from
the network motes. The manager uses this information to provide performance statistics to the application layer and
proactively solve problems in the network. Dynamic network optimization not only maintains network health, but also allows
the LTP5903-WHR to deliver deterministic power management.
6.2
Deterministic Power Management
Deterministic power management balances traffic in the network by diverting traffic around heavily loaded motes (for
example, motes with high reporting rates). In doing so, it reduces power consumption for these motes and balances power
consumption across the network. Deterministic power management provides predictable maintenance schedules to prevent
down time and lower the cost of network ownership. When combined with field devices using Dust Network’s industryleading low power radio technology, deterministic power management enables over a decade of battery life for network
motes.
6.3
Intelligent Routing
Intelligent routing provides each packet with an optimal path through the network. The shortest distance between two points
is a straight line, but in RF the quickest path is not always the one with the fewest hops. Intelligent routing finds optimal
paths by considering the link quality (one path may lose more packets than another) and the retry schedule, in addition to the
number of hops. The result is reduced network power consumption, elimination of in-network collisions, and unmatched
network scalability and reliability.
6.4
Bandwidth Flexibility
Efficient use of network resources enables Dust Networks to deliver bandwidth flexibility—the ability to assign different
levels of bandwidth to satisfy unique throughput and latency requirements. Bandwidth flexibly addresses the range of latency
and throughput needs of industrial automation applications such as request/response, fast file transfer, and alerting.
7.0
Interfaces
The LTP5903-WHR is designed for ease of integration by providing multiple data ports and well-defined software APIs.
Section 7.1 describes the LTP5903-WHR data ports, LEDs, and switches Section 7.1.5 describes the software functions that
are available through the data ports.
7.1
Hardware Interfaces
Table 15 Hardware Interface Summary
Port
8
Description
Pins
Ethernet
10/100Base-T Ethernet
RX_P, TX_P, RX_N, TX_N, RX_CT, TX_CT, nACT_LED, nLINK_LED
Serial 1
UART 5-pin
S1_TX, S1_RX, GND
Serial 2
UART 9-pin
S2_TX, S2_RX, S2_RTS, S2_CTS, GND
LED Status Indicator
Status indicators
¯¯¯
nLED_SUB, nLED_RADIO, nLED_JOIN, RST
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
7.1.1
10/100Base-T Ethernet Interface
Ideal for remote or high-bandwidth access, the Ethernet interface provides full configuration management and data access to
the LTP5903-WHR. The port connects to an IEEE 802.3 standard 10/100Base-T PHY, accessible through the board-to-board
J10 connector. An appropriate Ethernet design requires magnetics and an RJ-45 connector.
RX_P and RX_N are the receive-side differential pair (see section 8.2 for pinout). The Rx and Tx levels conform to
10/100Base-T Ethernet.
7.1.2
Serial 1 Interface
The Serial 1 interface is designed for embedded integration with controllers. This serial interface provides programmatic
access for configuration, management, and data access to the LTP5903-WHR. The port is a 5-pin LVTTL (3.3 V) serial
interface accessible through the board-to-board J10 connector.
Table 16 Serial 1 Parameters
Parameter
Value
Bit rate
115200
Parity
N
Data bits
8
Stop bit
1
Flow control
7.1.3
None
Serial 2 Interface
The LTP5903-WHR provides a UART interface with TX, RX, RTS, and CTS lines through the board-to-board J6 connector,
operating up to 115 kbps.
Table 17 Serial 2 Parameters
Parameter
Value
Bit rate
115200
Parity
N
Data bits
8
Stop bit
1
Flow control
7.1.4
None
LED Status Indicators
The LTP5903-WHR has LED status indicators on the top surface of the module, whose signals also pass through the boardto-board J10 connector.
Table 18 LED Status Indicators
LED Name
Signal Name
Power
¯¯¯
RST
7.1.5
nRESET_IN
Description
Color
Indicates 3.3V DC-DC converter is okay, lights when 5 V supply is
connected
Green
Indicates the manager is in the reset state
Red
Restore Signal
The LTP5903-WHR supports the ability to restore its configuration settings to the Dust factory defaults. This feature is most
useful in non-embedded applications where the LTP5903-WHR configuration may be different per installation (for example,
a manager’s IP setting is forgotten and therefore unreachable). Note that while the restore feature may be used to recover a
previously “unreachable” manager, all customizations to the manager will be lost, including configuration, logs, OTAP
directory files, and persistent mote information.
LTP5903-WHR Datasheet
Dust Networks
9
- ADVANCED INFORMATION -
The following factory default settings are restored:
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
IP address
PPP settings
Serial port settings
User name and password
Wireless network and mote configuration settings
Wireless network ID and common join key
Access control list (cleared)
Log files (cleared)
Mote list (cleared)
The Restore Switch signal input to the LTP5903-WHR includes a debounce circuit to support direct connection to a
mechanical push button, as illustrated in Figure 1.
Figure 1
Restore Switch Debounce Input Stage
The Restore Switch signal controls the restore function. The Restore Switch signal is only active for the first three seconds
after nRESET_IN is released. Usage of the Restore Switch signal is optional. If unused, the Restore Switch signal may be left
unconnected, since it is internally pulled inactive high.
tRST to RESTORE
nRESET_IN
Restore Switch
Figure 2
Restore Switch Signal Timing Diagram
Table 19 Restore Signal Timing Values
Parameter
tRST to RESTORE
10
Min
Typ
1
Dust Networks
Max
Units
20
s
Comments
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
7.2
Software Interfaces
The LTP5903-WHR provides well-defined software interfaces for easy integration. Table 20 describes which interfaces are
available via the various hardware ports. This section describes the software interfaces available via the hardware ports
described in section 7.2.1.
Table 20 LTP5903-WHR Software Interfaces
Hardware Port
Software Interface
Ethernet
XML API, Admin Toolset
Serial 1
<reserved>
Serial 2
Command line interface
7.2.1
Comments
XML API
The XML API is an open Extensible Markup Language (XML) interface that lets a client application send Remote Procedure
Call (RPC) requests to the LTP5903-WHR and receive responses and other data from the LTP5903-WHR via XML-RPC.
The API consists of a Control Channel and a Notification Channel. The Control Channel is used to establish connection and
exchange commands and information about the SmartMesh Network. The Notification Channel is used to stream data and
network events to the client program
7.2.2
Admin Toolset
The LTP5903-WHR provides a Web-based administrative tool called Admin Toolset. Through this interface, users may
configure IP settings, view logs, manually configure the system time, or enable the Network Time Protocol (NTP) client.
Users may also update LTP5903-WHR software as well as perform remote software updates on motes in the wireless
network.
7.2.3
Command Line Interface
The command line interface is for troubleshooting with the assistance of Dust Networks support.
8.0
Board-to-board Connectors
The LTP5903-WHR has two 40-pin FCI/Berg 61083-042400LF board-to-board connectors. For connector and pin locations,
see Figure 3 and Figure 4.
8.1
Figure 3
Connector Pin Numbering
Connector Pin Numbering (Bottom View)
LTP5903-WHR Datasheet
Dust Networks
11
- ADVANCED INFORMATION -
8.2
Pinout
Table 22 J10 Board-to-board Connector
Pin
Number
Pin Name
I/O Direction
1
GND
2
GND
3
RX_P
In
10/100Base-T
Ethernet
4
TX_P
Out
10/100Base-T
Ethernet
5
RX_N
In
10/100Base-T
Ethernet
6
TX_N
Out
10/100Base-T
Ethernet
7
RX_CT
In
10/100Base-T
Ethernet
8
TX_CT
Out
10/100Base-T
Ethernet
9
nACT_LED
Out
LVTTL Type 3
LED Status indicators
10
nLINK_LED
Out
LVTTL Type 3
11
+3V3
Out
3.3 V ± 5%
3.3 V Out
12
+3V3
Out
3.3 V ± 5%
3.3 V Out
13
Reserved
Do not connect
14
Reserved
Do not connect
15
Reserved
Do not connect
16
Reserved
Do not connect
Out
I/O Level
LVTTL Type 1
Interface Name
LED Status indicators
17
S1_TX
18
Reserved
Serial 1
19
S1_RX
In
LVTTL Type 1
Serial 1
20
Restore Switch
In*
LVTTL Type 2
Switch In
21
GND
22
nLED_SUB
Out
LVTTL Type 1
LED status indicators
23
Reserved
24
nLED_JOIN
Out
LVTTL Type 1
25
+3V3
Out
3.3 V ± 5%
26
Reserved
Do not connect
27
Reserved
Do not connect
28
Reserved
Do not connect
29
Reserved
Do not connect
30
Reserved
31
Reserved
Do not connect
32
Reserved
Do not connect
33
GND
34
Reserved
Do not connect
35
Reserved
Do not connect
36
Reserved
Do not connect
37
Reserved
Do not connect
38
Reserved
Do not connect
39
GND
40
GND
Do not connect
Do not connect
Out
LVTTL Type 1
LED status indicators
3.3 V Out
Do not connect
* Input includes a debounce input stage as illustrated in Figure 1.
12
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
Table 23 J6 Board-to-board Connector
Pin
Number
Pin Name
1
GND
2
GND
3
Reserved
4
S2_TX
5
Reserved
6
S2_RX
7
Reserved
I/O Direction
I/O Level
Interface Name
Do not connect
Out
LVTTL Type 1
Serial 2
Do not connect
In
LVTTL Type 1
Serial 2
Do not connect
8
S2_RTS
9
Reserved
Out
LVTTL Type 1
Serial 2
10
S2_CTS
11
Reserved
Do not connect
12
Reserved
Do not connect
13
Reserved
Do not connect
14
Reserved
Do not connect
Do not connect
In
LVTTL Type 1
Serial 2
15
GND
16
Reserved
Do not connect
17
Reserved
Do not connect
18
Reserved
Do not connect
19
Reserved
Do not connect
20
+3V3
Out
3.3 V ± 5%
3.3 V Out
21
+3V3
Out
3.3 V ± 5%
3.3 V Out
22
nRESET_OUT
Out
LVTTL Type 4
23
Reserved
24
GND
Reset low out
Do not connect
25
Reserved
26
RESET_OUT
27
Reserved
28
nRESET_IN
29
Reserved
Do not connect
30
Reserved
Do not connect
31
Reserved
Do not connect
32
+5V_IN
33
Reserved
34
+5V_IN
35
GND
Do not connect
Out
LVTTL Type 4
Do not connect
In
In
LVTTL Type 5
5.0 V ± 5%
Reset low in
Power In
Do not connect
In
5.0 V ± 5%
36
+5V_IN
In
5.0 V ± 5%
37
nLED_RADIO
Out
LED
38
Reserved
39
GND
40
GND
LTP5903-WHR Datasheet
Reset high out
Power In
Power In
LED status indicators
Do not connect
Dust Networks
13
- ADVANCED INFORMATION -
8.3
Recommended Mating Connectors
The user connections are made through J6 and J10 on the LTP5903-WHR, which are FCI/Berg 61083-042400LF board-toboard connectors. The mating connector should be an FCI/Berg 61082-04x400LF, where ‘x’ depends on the desired stack
height (see Table 24).
Table 24 Recommended Mating Connectors
Connector
Mated Height (mm)
FCI/Berg 61082-041400LF
6
FCI/Berg 61082-042400LF
10
FCI/Berg 61082-043400LF
14
9.0
Mechanical Specifications
9.1
LTP5903-WHR Mechanical Drawings
In laying out a design, locate the mating connectors by using the alignment pins and correlating pin numbers for orientation
(see Figure 3).
Figure 4
14
Top and Side Views
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
Figure 5
Bottom View
10.0
Regulatory and Standards Compliance
10.1
FCC Compliance
10.1.1
FCC Testing
The LTP5903-WHR Embedded Manager complies with Part 15.247 modular (Intentional Radiator) of the FCC rules and
regulations. In order to fulfill FCC certification requirements, products incorporating the LTP5903-WHR Embedded
Manager must comply with the following:
1. An external label must be provided on the outside of the final product enclosure specifying the FCC identifier, as
described in section 10.1.3 below.
2. The antenna must be electrically identical to the FCC-approved antenna specifications for the LTP5903-WHR as
described in 10.1.2, with the exception that the gain may be lower than specified in Table 25.
3. The device integrating the LTP5903-WHR may not cause harmful interference, and must accept any interference
received, including interference that may cause undesired operation.
LTP5903-WHR Datasheet
Dust Networks
15
- ADVANCED INFORMATION -
4. An unintentional radiator scan must be performed on the device integrating the LTP5903-WHR Embedded Manager, per
FCC rules and regulations, CFR Title 47, Part 15, Subpart B. See FCC rules for specifics on requirements for declaration
of conformity.
10.1.2
FCC-approved Antenna
The following are FCC-approved antenna specifications for the LTP5903-WHR.
Table 25 FCC-approved Antenna Specifications for the LTP5903-WHR
Gain
Pattern
+2 dBi maximum
10.1.3
Omni-directional
Polarization
Vertical
Frequency
2.4–2.4835 GHz
Connector
MMCX
OEM Labeling Requirements
The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. The outside of the final
product enclosure must have a label with the following (or similar) text specifying the FCC identifier. The FCC ID and
certification code must be in Latin letters and Arabic numbers and visible without magnification.
Contains transmitter module FCC ID: SJC-M2140
or
Contains FCC ID: SJC-M2140
10.2
IC Compliance
10.2.1
IC Testing
The LTP5903-WHR is certified for modular Industry Canada (IC) RSS-210 approval. The OEM is responsible for its product
to comply with IC ICES-003 and FCC Part 15, Sub. B - Unintentional Radiators. The requirements of ICES-003 are
equivalent to FCC Part 15 Sub. B and Industry Canada accepts FCC test reports or CISPR 22 test reports for compliance with
ICES-003.
10.2.2
IC-approved Antennae
The LTP5903-WHR is designed to operate with antennas meeting the specifications shown in Table 26. Antennas not
meeting these specifications are strictly prohibited for use with the LTP5903-WHR. The required antenna impedance is 50
Ohms. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Table 26 IC-approved Antenna Specifications for the LTP5903-WHR
Gain
Pattern
+2 dBi maximum
Omni-directional
Polarization
Vertical
Frequency
2.4–2.4835 GHz
Connector
MMCX
The following are IC-approved antenna specifications for the LTP5903-WHR.
10.2.3
OEM Labeling Requirements
The Original Equipment Manufacturer (OEM) must ensure that IC labeling requirements are met. The outside of the final
product enclosure must have a label with the following (or similar) text specifying the IC identifier. The IC ID and
certification code must be in Latin letters and Arabic numbers and visible without magnification.
Contains IC: 5853A-M2140
16
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
10.3
CE Compliance
10.3.1
Declaration of Conformity
We, Dust Networks, of 30695 Huntwood Ave, Hayward, CA 94544 USA, declare under our sole responsibility that our
product, SmartMesh WirelessHART LTP5903-WHR, and in combination with our accessories, to which this declaration
relates is in conformity with the appropriate standards ETSI EN 300 328, ETSI EN 301 489-17 and EN 60950, following the
provisions of Radio Equipment and Telecommunication Terminal Equipment Directive 99/5/EC with requirements covering
EMC Directive 2004/108/EC, and Low Voltage Directive 2006/95/EC.
10.3.2
European Compliance
If the LTP5903-WHR managers are incorporated into a product, the manufacturer must ensure compliance of the final
product to the European harmonized EMC and low-voltage/safety standards. A Declaration of Conformity must be issued for
each of these standards and kept on file as described in Annex II of the R&TTE Directive. Furthermore, the manufacturer
must maintain a copy of this LTP5903-WHR user documentation and ensure the final product does not exceed the specified
power ratings, antenna specifications, and/or installation requirements as specified in the user manual. If any of these
specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all
required standards.
10.3.3
OEM Labeling Requirements
The ‘CE’ marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials “CE”
taking the following form:
ƒ
ƒ
ƒ
If the CE marking is reduced or enlarged, the proportions given in the drawing below must be respected.
The CE marking must have a height of at least 5 mm except where this is not possible on account of the nature of the apparatus.
The CE marking must be affixed visibly, legibly, and indelibly.
Furthermore, since the usage of the 2400 – 2483.5 MHz band is not harmonized throughout Europe, the Restriction sign must
be placed to the right of the ‘CE’ marking as shown below. See the R&TTE Directive, Article 12 and Annex VII for more
information.
Figure 6
10.3.4
CE Label Requirements
Restrictions
Norway prohibits operation near Ny-Alesund in Svalbard. More information can be found at the Norway Posts and
Telecommunications site (www.npt.no).
10.4
Compliance to Restriction of Hazardous Substances (RoHS)
Restriction of Hazardous Substances (RoHS) is a directive that places maximum concentration limits on the use of cadmium
(Cd), lead (Pb), hexavalent chromium(Cr+6), mercury (Hg), Polybrominated Biphenyl(PBB) and Polybrominated Diphenyl
Ethers (PBDE). Dust Networks is committed to meeting the requirements of the European Community directive 2002/95/EC.
This product has been specifically designed to utilize RoHS compliant materials and to eliminate, or reduce, the use of
restricted materials to comply with 2002/95/EC.
The Dust Networks RoHS compliant design features include:
ƒ
RoHS compliant solder for solder joints
ƒ
RoHS compliant base metal alloys
ƒ
RoHS compliant precious metal plating
ƒ
RoHS compliant cable assemblies and connector choices
LTP5903-WHR Datasheet
Dust Networks
17
- ADVANCED INFORMATION -
10.5
Industrial Environment Operation
The LTP5903-WHR is designed to meet the specifications of a harsh industrial environment that includes:
ƒ
ƒ
Shock and Vibration—The LTP5903-WHR complies with high vibration pipeline testing, as specified in IEC 60770-1.
Temperature Extremes—The LTP5903-WHR is designed for industrial storage and operational temperature
range of –40 °C to +85 °C.
11.0 Order Information
LEAD FREE FINISH**
PART
MARKING
PACKAGE
DESCRIPTION
TEMPERATURE
RANGE
LTP5903IPC-WHRB???#PBF
LTP5903
4.050” x 2.190” x 0.775
PCB
-40 °C to 85 °C
LTP5903IPC-WHRC???#PBF
LTP5903
4.050” x 2.190” x 0.775
PCB
-40 °C to 85 °C
** See http://www.linear.com/ or contact your sales representative to determine the three digit software version field, ???.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
12.0
ƒ
18
Related Documentation
LTP5903 Integration Guide
Dust Networks
LTP5903-WHR Datasheet
- ADVANCED INFORMATION -
Trademarks
Eterna, mesh-to-the-edge, and Mote-on-Chip are trademarks of Dust Networks, Inc. The Dust Networks logo, Dust, Dust Networks, and SmartMesh are
registered trademarks of Dust Networks, Inc. The Linear logo is a registered trademark of Linear Technology Corporation. All third-party brand and
product names are the trademarks of their respective owners and are used solely for informational purposes.
Copyright
This documentation is protected by United States and international copyright and other intellectual and industrial property laws. It is solely owned by
Dust Networks, Inc. and its licensors and is distributed under a restrictive license. This product, or any portion thereof, may not be used, copied, modified,
reverse assembled, reverse compiled, reverse engineered, distributed, or redistributed in any form by any means without the prior written authorization of
Dust Networks, Inc.
RESTRICTED RIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g) (2)(6/87) and FAR
52.227-19(6/87), or DFAR 252.227-7015 (b)(6/95) and DFAR 227.7202-3(a), and any and all similar and successor legislation and regulation.
Disclaimer
This documentation is provided “as is” without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of
merchantability or fitness for a particular purpose.
This documentation might include technical inaccuracies or other errors. Corrections and improvements might be incorporated in new versions of the
documentation.
Dust Networks does not assume any liability arising out of the application or use of any products or services and specifically disclaims any and all
liability, including without limitation consequential or incidental damages.
Dust Networks products are not designed for use in life support appliances, devices, or other systems where malfunction can reasonably be expected to
result in significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Dust Networks customers using or selling these
products for use in such applications do so at their own risk and agree to fully indemnify and hold Dust Networks and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Dust Networks was
negligent regarding the design or manufacture of its products.
Dust Networks reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products or services at any
time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should
verify that such information is current and complete. All products are sold subject to Dust Network's terms and conditions of sale supplied at the time of
order acknowledgment or sale.
Dust Networks does not warrant or represent that any license, either express or implied, is granted under any Dust Networks patent right, copyright, mask
work right, or other Dust Networks intellectual property right relating to any combination, machine, or process in which Dust Networks products or
services are used. Information published by Dust Networks regarding third-party products or services does not constitute a license from Dust Networks to
use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from Dust Networks under the patents or other intellectual property of Dust Networks.
Dust Networks, Inc is a wholly owned subsidiary of Linear Technology Corporation.
© Dust Networks, Inc. 2012. All Rights Reserved.
Document Status
Document Number:
020-0051 rev 3 SmartMesh WirelessHART LTP5903-WHR Datasheet
Last Revised:
July 19, 2012
Product Status
Definition
Advanced Information
Planned or under development
This datasheet contains the design specifications for product
development. Dust Networks reserves the right to change specifications in
any manner without notice.
Preliminary
Engineering samples and
pre-production prototypes
This datasheet contains preliminary data; supplementary data will be
published at a later time. Dust Networks reserves the right to make
changes at any time without notice in order to improve design and supply
the best possible product. The product is not fully qualified at this point.
No Identification Noted
Full production
This datasheet contains the final specifications. Dust Networks reserves
the right to make changes at any time without notice in order to improve
design and supply the best possible product.
Obsolete
Not in production
This datasheet contains specifications for a product that has been
discontinued by Dust Networks. The datasheet is printed for reference
information only.
LTP5903-WHR Datasheet
Dust Networks
19