Ordering number : ENA1157B LV8760T Bi-CMOS LSI Forward/Reverse H-bridge Driver Overview The LV8760T is an H-bridge driver that can control four operation modes (forward, reverse, brake, and standby) of a motor. The low on-resistance, zero standby current, highly efficnet IC is optimal for use in driving brushed DC motors for office equipment. Features • Forward/reverse H-bridge motor driver: 1 channel • Built-in current limiter circuit • Built-in thermal protection circuit • Built-in short-circuit protection function Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Supply voltage Symbol Conditions VM max VCC max Output peak current IO peak Output continuous current IO max Logic input voltage Allowable power dissipation tw ≤ 20ms, duty 5% VIN Pd max Mounted on a specified board. * Ratings Unit 38 V 6 V 4 A 3 A -0.3 to VCC+0.3 V 3.3 W Operating temperature Topr -20 to +85 °C Storage temperature Tstg -55 to +150 °C * Specified circuit board : 90mm×90mm×1.6mm, glass epoxy 2-layer board (2S0P), with backside mounting. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 82411 SY 20110808-S00001/22410 SY 20100222-S00002/42308 MS PC 20080319-S00001 No.A1157-1/11 LV8760T Allowable Operating Ratings at Ta = 25°C Parameter Supply voltage range Symbol Conditions Ratings Unit VM 9 to 35 VCC 3 to 5.5 V V VREF input voltage VREF 0 to VCC-1.8 V Logic input voltage VIN 0 to VCC V Electrical Characteristics at Ta = 25°C, VM = 24V, VCC = 5V, VREF = 1.5V Ratings Parameter Symbol Conditions Unit min typ max General Standby mode current drain 1 IMst PS = “L” 1 μA Standby mode current drain 2 ICCst PS = “L” 1 μA Operating mode current drain 1 IM PS = “H”, IN1 = “H”, with no load 1 1.3 mA Operating mode current drain 2 ICC PS = “H”, IN1 = “H”, with no load 3 4 mA 5 5.25 VREG output voltage VREG IO = -1mA 4.75 V VCC low-voltage cutoff voltage VthVCC 2.5 2.7 2.9 V Low-voltage hysteresis voltage VthHIS 120 150 180 mV Thermal shutdown temperature TSD Design guarantee * 155 170 185 °C ΔTSD Design guarantee * Ron1 IO = 3A, sink side Ron2 IO = -3A, source side Thermal hysteresis width °C 40 Output block Output on resistance Output leakage current IOleak 0.2 0.25 Ω 0.32 0.40 Ω 50 μA VO = 35V Rising time tr 10% to 90% 200 500 ns Falling time tf 90% to 10% 200 500 ns tpLH IN1 or IN2 to OUTA or OUTB (L → H) 550 700 ns tpHL IN1 or IN2 to OUTA or OUTB (H → L) 550 700 ns Step-up voltage VGH VM = 24V 28.7 29.8 V Rising time tONG VG = 0.1μF 250 500 μs 140 165 kHz Input output delay time Charge pump block Oscillation frequency Fcp 28.0 115 Control system input block Logic pin input current 1 IINL VIN = 0.8V adaptive pin : PS 5.6 8 10.4 μA IINH VIN = 5V adaptive pin : PS 56 80 104 μA IINL VIN = 0.8V adaptive pin : IN1, IN2 5.6 8 10.4 μA IINH VIN = 5V adaptive pin : IN1, IN2 35 50 65 μA Logic pin input H-level voltage VINH adaptive pin : PS, IN1, IN2 2.0 Logic pin input L-level voltage VINL adaptive pin : PS, IN1, IN2 Logic pin input current 2 V 0.8 V Current limiter block VREF input current IREF Current limit comparator Vthlim μA -0.5 VREF = 1.5V 0.285 0.3 0.315 V 1.6 2.0 2.4 μs threshold voltage Blanking time Tblk Short-circuit protection block SCP pin charge current Comparator threshold voltage Iscp Vthscp SCP = 0V 3.5 5 6.5 μA 0.8 1 1.2 V * Design guarantee value and no measurement is made. No.A1157-2/11 LV8760T Package Dimensions unit : mm (typ) 3279 TOP VIEW BOTTOM VIEW 6.5 20 0.5 6.4 4.4 11 10 1 0.65 Exposed Die-Pad 0.15 0.22 (1.0) 0.08 SIDE VIEW 1.2max (0.33) SANYO : TSSOP20J(225mil) Pin Assignment PGND 1 20 VCC OUTB 2 19 SCP OUTB 3 18 VREF RNF 5 VM 6 VM 7 LV8760T RNF 4 17 IN2 16 IN1 15 REG5 14 CP1 OUTA 8 13 CP2 OUTA 9 12 VG PS 10 11 GND No.A1157-3/11 LV8760T Pd max – Ta Allowable power dissipation, Pd max – W 4.0 3.30 *1 With Exposed Die-Pad substrate *2 Without Exposed Die-Pad *1 3.0 2.0 1.60 *2 1.72 1.0 0.83 0 – 20 0 20 40 60 80 100 Ambient temperature, Ta – °C Substrate Specifications (Substrate recommended for operation of LV8760T) Size : 90mm × 90mm × 1.6mm (two-layer substrate [2S0P]) Material : Glass epoxy Copper wiring density : L1 = 95% / L2 = 95% L1 : Copper wiring pattern diagram L2 : Copper wiring pattern diagram Cautions 1) The data for the case with the Exposed Die-Pad substrate mounted shows the values when 90% or more of the Exposed Die-Pad is wet. 2) For the set design, employ the derating design with sufficient margin. Stresses to be derated include the voltage, current, junction temperature, power loss, and mechanical stresses such as vibration, impact, and tension. Accordingly, the design must ensure these stresses to be as low or small as possible. The guideline for ordinary derating is shown below : (1)Maximum value 80% or less for the voltage rating (2)Maximum value 80% or less for the current rating (3)Maximum value 80% or less for the temperature rating 3) After the set design, be sure to verify the design with the actual product. Confirm the solder joint state and verify also the reliability of solder joint for the Exposed Die-Pad, etc. Any void or deterioration, if observed in the solder joint of these parts, causes deteriorated thermal conduction, possibly resulting in thermal destruction of IC. No.A1157-4/11 GND VCC PS REG5 VG SCP Short-circuit Protection Circuit Oscillation circuit LVS TSD Reference Voltage Circuit Charge pump CP1 CP2 VM OUTA OUTB IN1 IN2 Output control logic M Current Limiter Circuit RNF + + VREF PGND LV8760T Block Diagram Output preamplifier stage Output preamplifier stage + - + - No.A1157-5/11 LV8760T Pin Functions Pin No. Pin Name Pin Functtion 16 IN1 Output control signal input pin 1. 17 IN2 Output control signal input pin 2. Equivalent Circuit VCC 10kΩ 100kΩ GND 10 PS Power save signal input pin. VCC 50kΩ 10kΩ 10kΩ 50kΩ GND 18 VREF Reference voltage input pin for output VCC current limit setting. 500Ω GND 19 SCP Short-circiut protection circuit, detection time setting capacitor connection pin. VCC 500Ω GND 20 VCC Power supply connection pin for control block. Continued on next page. No.A1157-6/11 LV8760T Continued from preceding page. Pin No. Pin Name Pin Functtion 6, 7 VM Motor power-supply connection pin. 8, 9 OUTA OUTA output pin. 4, 5 RNF Current sense resistor connection pin. 2, 3 OUTB OUTB output pin. 1 PGND Power ground. Equivalent Circuit 6 7 REG5 8 9 2 3 500Ω 500Ω 4 5 1 GND 14 CP1 Charge pump capacitor connection pin. 13 CP2 Charge pump capacitor connection pin. 12 VG Charge pump capacitor connection pin. 14 REG5 6 7 13 12 100Ω GND 15 REG5 Internal reference voltage output pin. VM 74kΩ 2kΩ 25kΩ GND 11 GND Ground. No.A1157-7/11 LV8760T DC Motor Driver 1.DCM output control logic Contol Input PS IN1 Output IN2 OUTA OUTB Mode L * * OFF OFF Standby H L L OFF OFF Output OFF H H L H L CW (forward) H L H L H CCW (reverse) H H H L L Brake 2.Current limit control timing chart Limit current Output current OUTA OUTB toff CHARGE SLOW Braking operation time in current limit mode can be set by connecting a capacitor between SCP and GND pins. This setting is the same as the time setting required to turn off the outputs when an output short-circuit occurs as explained in the section entitled "Output Short-circuit Protection Function." See "Output Short-circuit Protection Function," for the settinig procedure. 3.Setting the current limit value The current limit value of the DCM driver is determined by the VREF voltage and the resistance (RNF) connected across the RNF and GND pins using the following formula : Ilimit [A] = (VREF [V] /5) /RNF [Ω]) Assuming VREF = 1.5V, RNF = 0.2Ω, the current limit is : Ilimit = 1.5V/5/0.2Ω = 1.5A No.A1157-8/11 LV8760T Output short-circuit protection function The LV8760T incorporates an output short-circuit protection circuit. It turns the ouputs off to prevent destruction of the IC if a problem such as an output pin being shorted to the motor power supply or ground occurs. 1.Protection function operation (Latch method) The short-circuit protection circuit is activated when it detects the output short-circuit state. If the short-circuit state continues for the internally preset period (≈ 4μs), the protection circuit turns off the output from which the short-circuit state has been detected. Then it turns the output on again after a lapse of the timer latch time described later. If the short-circuit state is still detected, it changes all the outputs to the standby mode and retains the state. The latched state is released by setting the PS to L. Output ON H-bridge output state Output ON Output OFF Standby state Threshold voltage 4μs SCP voltage Short-circuit detection state Short- Release circuit Short-circuit Internal counter 1st counter start 1st counter 1st counter stop start 1st counter end 2nd counter start 2nd counter end 2.How to set the SCP pin constant (timer latch-up setting) The user can set the time at which the outputs are turned off when a short-circuit occurs by connecting a capacitor across the SCP and GND pins. The value of the capacitor can be determined by the following formula : Timer latch-up : Tocp Tocp ≈ C × V/I [s] V : Comparator threshold voltage (1V typical) I : SCP charge current (5μA typical) When a capacitor with a capacitance of 50pF is connected across the SCP and GND pins, for example, Tscp is calculated as follows : Tscp = 50pF × 1V/5μA = 10μs No.A1157-9/11 LV8760T Application Circuit Example (When you use the current limit function) 35kΩ 15kΩ 0.1μF 1 PGND VCC 20 2 OUTB SCP 19 3 OUTB VREF 18 4 RNF 10μF 5 RNF - + 6 VM 7 VM 8 OUTA CP2 13 9 OUTA VG 12 + - 100pF 0.22Ω LV8760T M IN2 17 Control input IN1 16 REG5 15 0.1μF CP1 14 0.1μF 0.1μF Control input 10 PS GND 11 Setting the current limit value When VCC = 5V, Vref = 1.5V Ilimit = Vref/5/RNF = 1.5V/5/0.22Ω = 1.36A Setting the current limit regeneration time and short-circuit detection time Tscp ≈ C × V/I = 100pF × 1V/5μA = 20μs PS No.A1157-10/11 LV8760T (When you do not use the current limit function) 1 PGND VCC 20 2 OUTB SCP 19 3 OUTB VREF 18 4 RNF 5 RNF 6 VM 7 VM 8 OUTA CP2 13 9 OUTA VG 12 + - 100pF - + Control input 10 PS LV8760T M IN2 17 Control input IN1 16 REG5 15 CP1 14 GND 11 Setting at short-circuit state detection time TSCP≒C·V/I =100pF·1V/5µA =20µs *Do the following processing when you do not use the current limit function. · It is short between RNF-GND. · The terminal VREF is hung on suitable potential of VCC or less. SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of August, 2011. Specifications and information herein are subject to change without notice. PS No.A1157-11/11