M74HC243 QUAD BUS TRANSCEIVER (3 - STATE) ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 11ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 243 DESCRIPTION The M74HC243 is an high speed CMOS QUAD BUS TRANSCEIVER (3-STATE) fabricated with silicon gate C2MOS technology. The M74HC243 is a 3-state bidirectional non-inverting buffer and is intended for two way asynchronous communication between data buses. It has high drive current outputs which DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC243B1R M74HC243M1R T&R M74HC243RM13TR M74HC243TTR enable high speed operation when driving large bus capacitance. The device has one active high enable (GBA), and one active low enable (GAB) All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 2001 1/11 M74HC243 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 GAB 2, 12 3, 4, 5, 6 11, 10, 9, 8 13 7 NC 1A to 4A 1B to 4B GBA GND VCC 14 NAME AND FUNCTION Output Enable Input (Active LOW) Not Connected Data Inputs/Outputs Data Inputs/Outputs Output Enable Input Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS FUNCTION OUTPUTS LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays 2/11 GAB GBA H L H L H L L H A BUS B BUS OUTPUT INPUT INPUT OUTPUT HIGH IMPEDANCE HIGH IMPEDANCE A=B B=A Z Z M74HC243 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Supply Voltage Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 35 mA ± 70 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Value Supply Voltage Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C Input Rise and Fall Time tr, tf VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/11 M74HC243 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II IOZ ICC 4/11 Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-6.0 mA 4.18 4.31 4.13 4.10 5.68 Unit V V 6.0 IO=-7.8 mA 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=6.0 mA 0.17 0.26 0.33 0.40 6.0 IO=7.8 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 5.5 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 µA 6.0 VI = VCC or GND 4 40 80 µA 5.8 5.63 5.60 V M74HC243 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time tPZL tPZH High Impedance Output Enable Time tPLZ tPHZ High Impedance Output Disable Time VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C CL (pF) Min. 50 50 150 50 RL = 1 KΩ 150 RL = 1 KΩ 50 RL = 1 KΩ Typ. Max. 25 7 6 39 13 11 51 17 14 57 18 15 70 22 19 45 20 17 60 12 10 90 18 15 145 29 25 145 29 25 175 35 30 150 30 26 -40 to 85°C -55 to 125°C Min. Min. Max. 75 15 13 115 23 20 180 36 31 180 36 31 220 44 37 190 38 32 Unit Max. 90 18 15 135 27 23 220 44 37 220 44 37 265 53 45 225 45 38 ns ns ns ns ns ns CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 35 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 5/11 M74HC243 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) 6/11 M74HC243 WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 7/11 M74HC243 Plastic DIP-14 MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 1.39 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 8/11 M74HC243 SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) PO13G 9/11 M74HC243 TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 10/11 M74HC243 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11