EVALUATION KIT AVAILABLE MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies General Description Features and Benefits The MAX258 is a 500mA, push-pull transformer driver designed to provide a simple solution for isolated power supplies. The IC has an internal oscillator and operates from a single +3.0V to +5.5V supply. The transformer’s secondary-to-primary winding ratio defines the output voltage, allowing selection of virtually any isolated output voltage with galvanic isolation. The device features an integrated oscillator driving a pair of n-channel power switches. Internal circuitry guarantees a fixed 50% duty cycle to prevent DC current flow through the transformer. The IC operates with up to 500mA of continuous current and features undervoltage lockout and thermal shutdown. The IC includes a low-current shutdown mode to reduce the overall supply current to less than 5µA (max) when the driver is disabled. The MAX258 is available in a small 8-pin (2mm x 3mm) TDFN package and is specified over the -40°C to +125°C temperature range. ● Simple, Flexible Design •+3.0V to +5.5V Supply Range • Low RON 300mΩ (max) at 4.5V • Up to 90% Efficiency • Provides Up to 500mA to the Transformer • 250kHz or 600kHz Internal Oscillator Frequency • -40ºC to +125ºC Temperature Range ● Integrated System Protection • Undervoltage Lockout • Thermal Shutdown ● Saves Space on Board • Small 8-Pin TDFN Package (2mm x 3mm) Applications ● ● ● ● Power Meter Data Interface Isolated Fieldbus Interface Medical Equipment Isolated Analog Front-End Ordering Information appears at end of data sheet. Typical Operating Circuit 5V 1µF VDD HICLK T2 1CT:1.3CT 1µF ISOLATED VOUT MAX258 10µF EN T1 GND PGND For related parts and recommended products to use with this part, refer to www.maximintegrated.com/MAX258.related. 19-6696; Rev 0; 5/13 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Absolute Maximum Ratings (All voltages referenced to GND.) VDD, HICLK, EN.......................................................-0.3V to +6V T1, T2..................................................................-0.3V to +16.5V T1, T2 Maximum Continuous Current...............................+1.75A Continuous Power Dissipation (TA = +70ºC) TDFN (Multilayer Board) (derate 16.7mW/ºC above +70ºC)...........................1333.3mW Operating Temperature Range...........................-40ºC to +125ºC Junction Temperature....................................................... +150ºC Storage Temperature Range..............................-65ºC to +150°C Lead Temperature (soldering, 10s).................................. +300°C Soldering Temperature (reflow)........................................+260°C Package Thermal Characteristics (Note 1) TDFN (Multilayer) Junction-to-Ambient Thermal Resistance (θJA)...........60°C/W Junction-to-Case Thermal Resistance (θJC)................11°C/W Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VDD = +3.0V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values at VDD = +5.0V and TA = +25ºC.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 5.5 V DC CHARACTERISTICS Supply Voltage Range VDD 3.0 VHICLK = 0V 1.1 1.8 VHICLK = VDD 2.1 3.5 Supply Current IDD VEN = 0V, T1 and T2 not connected Disable Supply Current IDIS VEN = VDD, T1, T2, HICLK connected to GND or VDD (Note 3) Driver Output Resistance RO IOUT = 500mA Undervoltage Lockout Threshold VUVLO Undervoltage Lockout Threshold Hysteresis VUVLO_HYST T1, T2 Leakage Current ILKG 5 VDD = 3.0V 160 350 VDD = 4.5V 145 300 2.75 2.9 VDD rising 2.6 250 VEN = VDD, T1, T2 = 0V or VDD -1 mA µA mΩ V mV +1 µA LOGIC SIGNALS (EN, HICLK) Input Logic-High Voltage VIH Input Logic-Low Voltage VIL Input Leakage Current IIL www.maximintegrated.com 2 EN, HICLK = 0V or 5.5V -1 V 0.8 V +1 µA Maxim Integrated │ 2 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Electrical Characteristics (continued) (VDD = +3.0V to 5.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values at VDD = +5.0V and TA = +25ºC.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX VHICLK = 0V 237 250 263 VHICLK = VDD 564 600 636 UNITS AC CHARACTERISTICS Switching Frequency fSW T1, T2 Duty Cycle D T1, T2 Slew Rate tSLEW Crossover Dead Time tDEAD Figure 1 kHz 50 % Figure 1 200 V/µs Figure 1 50 ns PROTECTION Thermal-Shutdown Threshold TSHDN +160 ºC Thermal-Shutdown Hysteresis TSHDN_HYS 30 ºC Note 2: All units are 100% production tested at TA = +25ºC. Specifications over temperature are guaranteed by design. Note 3: Disable supply current includes output-switch-leakage currents. VDD 100I T1, T2 50pF 2 x VDD T1 0V 2 x VDD tDEAD tDEAD T2 0V Figure 1. T1, T2 Timing Diagram www.maximintegrated.com Maxim Integrated │ 3 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Typical Operating Characteristics (VDD = +5V, TA = +25°C, unless otherwise noted.) HICLK = VDD 510 460 410 360 HICLK = GND 310 260 VDD = 3.3V 0.07 0.06 0.05 VDD = 5V 0.04 0.03 0.02 0.01 -45 -20 5 30 55 80 105 0 130 0.1 0.2 0.3 0.4 0.10 0.20 0.10 0.20 TA = +85°C TA = -40°C 0 LOAD CURRENT (A) www.maximintegrated.com 0.20 0.30 0.40 MAX258 toc07 93 91 89 87 VDD = 5V 85 83 81 75 VDD = 4.5V VDD = 5.5V HICLK = GND 1:1:1.3:1.3 HALO TGM-H240V8LF TRANSFORMER 77 0.40 0.10 HICLK = GND 1:1:1.3:1.3 HALO TGM-H240V8LF TRANSFORMER EFFICIENCY vs. LOAD CURRENT 79 0.30 0.4 TA = +25°C 95 MAX258 toc06 1:1:1:3:1:3 HALO TGM-H240V8LF TRANSFORMER 0.3 LOAD CURRENT (A) EFFICIENCY (%) EFFICIENCY (%) 80 0.2 TA = +125°C 82 0.25 HICLK = VDD 0 0.1 0 84 78 0.15 HICLK = GND 70 HICLK = GND 1:1:1.3:1.3 HALO TGM-H240V8LF TRANSFORMER 2 80 90 75 3 86 EFFICIENCY vs. LOAD CURRENT 85 4 EFFICIENCY vs. LOAD CURRENT LOAD CURRENT (A) 95 5 88 HICLK = GND 1:1:2:2 HALO TGM-H260V8LF TRANSFORMER 0.05 6 LOAD CURRENT (A) EFFICIENCY (%) 8 7 0 7 0 0.5 90 9 1 0 0 MAX258 toc04 ISOLATED OUTPUT VOLTAGE (V) 11 10 3 2 8 1 ISOLATED OUTPUT VOLTAGE vs. LOAD CURRENT 6 5 4 9 OUTPUT CURRENT (A) TEMPERATURE (°C) 12 10 MAX258 toc05 210 0.08 ISOLATED OUTPUT VOLTAGE vs. LOAD CURRENT MAX258 toc03 560 T1/T2 OUTPUT VOLTAGE LOW (V) 610 0.09 ISOLATED OUTPUT VOLTAGE (V) 0.10 MAX258 toc01 SWITCHING FREQUENCY (kHz) 660 T1/T2 OUTPUT VOLTAGE LOW vs. OUTPUT CURRENT MAX258 toc02 SWITCHING FREQUENCY vs. TEMPERATURE 0 0.1 0.2 0.3 0.4 LOAD CURRENT (A) Maxim Integrated │ 4 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Typical Operating Characteristics (continued) (VDD = +5V, TA = +25°C, unless otherwise noted.) TA = +25°C 89 87 85 TA = -40°C 83 81 77 75 TA = +125°C HICLK = GND 1:1:2:2 HALO TGM-H260V8LF TRANSFORMER 79 0 0.05 0.10 0.15 0.20 0.25 EFFICIENCY (%) 87 HICLK = VDD 85 83 81 1:1:2:2 HALO TGM-H260V8LF TRANSFORMER 75 0 0.05 0.10 0.15 0.25 0.20 LOAD CURRENT (A) VDD = 3.3V MAX258 toc10 VDD = 3.6V 91 89 77 EFFICIENCY vs. LOAD CURRENT 93 HICLK = GND 91 79 LOAD CURRENT (A) 95 93 EFFICIENCY (%) EFFICIENCY (%) 91 MAX258 toc08 TA = +85°C 93 EFFICIENCY vs. LOAD CURRENT 95 MAX258 toc09 EFFICIENCY vs. LOAD CURRENT 95 SWITCHING WAVEFORMS MAX258 toc11 89 T1 5V/div 87 0V 85 VDD = 3.0V 83 81 79 77 75 T2 5V/div 0V HICLK = GND 1:1:2:2 HALO TGM-H260V8LF TRANSFORMER 0 0.05 0.10 HICLK = GND 0.15 LOAD CURRENT (A) www.maximintegrated.com 0.20 0.25 RLOAD = 1kΩ 1µs/div Maxim Integrated │ 5 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Pin Configuration TOP VIEW T1 PGND T2 GND 8 7 6 5 MAX258 *EP + 1 VDD 2 3 GND HICLK 4 EN TDFN *EXPOSED PAD—CONNECT TO GND Pin Description PIN NAME 1 VDD Power-Supply Input. Bypass VDD to GND with a 1µF capacitor as close as possible to the device. 2, 5 GND Logic and Analog Ground 3 HICLK 4 EN Active-Low Enable Input. Drive EN low to enable the device. Drive EN high to disable the device. 6 T2 Transformer Drive Output 2 7 PGND 8 T1 Transformer Drive Output 1 — EP Exposed Pad. Internally connected to GND. Connect EP to a large ground plane to maximize thermal performance; not intended as an electrical connection point. www.maximintegrated.com FUNCTION Internal Oscillator Frequency Select Input. Drive HICLK high to set the internal oscillator to a 600kHz switching frequency. Drive HICLK low to set the internal oscillator to a 250kHz switching frequency. Power Ground. The transformer primary current flows through PGND. Ensure a low-resistance connection to ground. Maxim Integrated │ 6 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Functional Diagram VDD T1 UVLO MAX258 HICLK DRIVER T2 FLIPFLOP OSC EN GND Detailed Description The MAX258 is an integrated primary-side transformer driver for isolated power-supply circuits. An on-board oscillator and internal MOSFETs provide up to 500mA of drive current to the primary windings of a center-tapped transformer. The IC features an internal oscillator for autonomous operation. An internal flip-flop stage guarantees a fixed 50% duty cycle to prevent DC current flow in the transformer. The device operates from a single +3.0V to +5.5V supply and includes undervoltage lockout for controlled startup. Thermal shutdown circuitry provides additional protection against excessive power dissipation. Isolated Power-Supply Application The IC allows a versatile range of secondary-side rectification circuits (see Figure 2). The primary-to-secondary transformer winding ratio can be chosen to adjust the isolated output voltage. The device allows up to 500mA of current into the primary transformer winding with a supply voltage up to +5.5V. www.maximintegrated.com PGND Internal Oscillator The device includes an internal oscillator with a guaranteed 50% duty cycle. Drive the HICLK input high to set the internal oscillator frequency to 600kHz (typ). Drive the HICLK input low to set the internal oscillator frequency to 250kHz (typ). Slew-Rate Control The T1 and T2 drivers feature a controlled slew rate to limit EMI. Disable Mode The IC includes a pin-selectable disable mode to reduce current consumption. In disable mode the device consumes less than 5µA (max) of supply current. The T1 and T2 outputs are high impedance in disable mode. Power-Up and Undervoltage Lockout The IC provides an undervoltage lockout feature to ensure a controlled power-up state and prevent operation before the oscillator has stabilized. On power-up and during normal operation, if the supply voltage drops below VUVLO, the undervoltage-lockout circuit forces the device into disable mode. The T1 and T2 outputs are high impedance in disable mode. Maxim Integrated │ 7 MAX258 T1 500mA, Push-Pull Transformer Driver for Isolated Power Supplies High-Temperature Operation 1CT:nCT + - VIN VOUT = nVIN - VD T2 VD = DIODE FORWARD VOLTAGE (A) PUSH-PULL RECTIFICATION T1 1CT:nCT Power-Supply Decoupling + VIN VOUT = 2(nVIN - VD) - T2 VD = DIODE FORWARD VOLTAGE (B) VOLTAGE DOUBLER T1 When the device is operated under high ambient temperatures, the power dissipated in the package can raise the junction temperature close to the thermal shutdown threshold. Under such temperature conditions, the power dissipation should be held low enough that the junction temperature observes a factor of safety margin. The maximum junction temperature should be held below +140°C. Use the package’s thermal resistance to calculate the junction temperature. 1CT:nCT Bypass VDD to ground with a 1µF ceramic capacitor as close as possible to the device. Connect at least 10µF between VDD and ground as close as possible to the primary-side center tap of the transformer. This capacitor helps to stabilize the voltage on the supply line and protects the IC against large voltage spikes on VDD. Output Voltage Regulation VIN + VOUT = nVIN - 2VD T2 VD = DIODE FORWARD VOLTAGE (C) FULL-WAVE RECTIFIER Figure 2. Secondary-Side Rectification Topologies Thermal Shutdown The device is protected from overtemperature damage by integrated thermal-shutdown circuitry. When the junction temperature (TJ) exceeds +160ºC (typ), the device is disabled. The device resumes normal operation when TJ falls below +130°C (typ). Applications Information Power Dissipation The power dissipation of the device is approximated by: PD = (RO x IPRI2) + (IDD x VDD) where RO is the resistance of the internal FET drivers and IPRI is the load current flowing into T1 and T2. Ensure that the power dissipation of the MAX258 is kept below the Absolute Maximum Ratings for proper operation. www.maximintegrated.com For many applications, the unregulated output of the circuit meets output voltage tolerances. This configuration represents the highest efficiency possible. When the load currents on the transformer’s secondary side are low, the output voltage of the rectifier can strongly increase. To protect downstream circuitry, limit the output voltage when operating the circuit under low load conditions. If the minimum output load current is less than approximately 5mA, connect a zener diode from the output node of the rectifier to ground to limit the output voltage to a safe value. For applications requiring a regulated output voltage, Maxim provides several solutions. In the following examples, assume a tolerance of ±10% for the input voltage. Example 1: 5V to Isolated, Unregulated 6V In the circuit of Figure 3, the MAX258 is used to generate an isolated 5V output. For a minimum input voltage of 5V, the output voltage of the rectifier is approximately 6V. Example 2: 3.3V to Isolated, Regulated 5V In the circuit of Figure 4, the MAX8881 low-dropout linear regulator regulates the isolated output voltage to 5V. A 1:2 center-tapped transformer is used to step-up the secondary-side voltage from a 3.3V input. For a minimum input voltage of 3.3V, the output voltage of the rectifier is approximately 6V. Maxim Integrated │ 8 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies 5V 1µF VDD T2 HICLK 1CT:1.3CT 1µF MAX258 6V ISO OUTPUT 10µF EN T1 GND PGND Figure 3. 5V to Isolated, Unregulated 6V Application Circuit 3.3V 1µF VDD T2 HICLK 1CT:2CT IN 1µF MAX258 SHDN OUT MAX8881 FB 5V ISO OUTPUT 4.7µF 10µF EN T1 GND GND PGND Figure 4. 3.3V to Isolated, Regulated 5V Application Circuit PCB Layout Guidelines ensuring that the current flowing through the primary-side center tap of the transformer does not flow through the same trace that connects the supply pin of the MAX258 to the VDD source, and connect the primary-side center tap to the VDD supply using a very low inductance connection. The traces from T1 and T2 to the transformer must be low-resistance and low-inductance paths. Locate the transformer as closely as possible to the MAX258 using short, wide traces. Exposed Pad As with all power-supply circuits, careful PCB layout is important to achieve low switching losses and stable operation. Connect the exposed pad to a solid copper ground plane for optimum thermal performance. If possible, use a power plane for all VDD connections to the MAX258 and the primary-side of the transformer. If a power plane is not available, avoid damage to the IC by www.maximintegrated.com For optimal thermal performance, ensure that the exposed pad has a low thermal resistance connection to the ground plane. Failure to provide a low thermal impedance path to the ground plane results in excessive junction temperatures when dissipating high power. Maxim Integrated │ 9 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Component Selection Transformer Selection Transformer selection for the MAX258 can be simplified by the use of the ET product. The ET product relates the maximum allowable magnetic flux density in a transformer core to the voltage across a winding and switching period. Inductor magnetizing current in the primary winding changes linearly with time during the switching period of the device. Each transformer has a minimum ET product, though not always stated on the transformer data sheet. Ensure that the transformer selected for use with the device has an ET product of at least ET = VDD/(2 x fSW) for each half of the primary winding, where fSW is the minimum switching frequency of the T1 and T2 ouputs. Select a transformer with sufficient ET product for each half of the primary winding to ensure that the transformer does not saturate during operation. Saturation of the magnetic core results in significantly reduced inductance of the primary, and therefore in a large increase in current flow. For example, when HICLK is low, the required transformer ET product to the center tap for an application with VDD (max) = 5.5V, is 13.1V-µs. An application with VDD (max) = 3.3V has a transformer ET product to the center tap requirement of 7.9V-µs. In addition to the constraint on ET product, choose a transformer with low leakage inductance and low DC-winding resistance. Power dissipation of the transformer due to the copper loss is approximated as: PD_TX = ILOAD2 x (RPRI /N2 + RSEC) where RPRI is the DC-winding resistance of the primary, and RSEC is the DC-winding resistance of the secondary. In most cases, an optimum is reached when RSEC = RPRI /N2. For this condition, the power dissipation is equal for the primary and secondary windings. As with all power-supply designs, it is important to optimize efficiency. In designs incorporating small transformers, the possibility of thermal runaway makes low transformer efficiencies problematic. Transformer losses produce a temperature rise that reduces the efficiency of the transformer. The lower efficiency, in turn, produces an even larger temperature rise. To ensure that the transformer meets these requirements under all operating conditions, the design should focus on the worst-case conditions. The most stringent demands on ET product arise for maximum input voltage, minimum switching frequency, and maximum temperature and load current. Additionally, the worst-case values for transformer and rectifier losses should be considered. The primary must be center-tapped; however the secondary winding may or may not be center-tapped, depending on the rectifier topology used. The phasing between primary and secondary windings is not critical. The transformer turns ratio must be set to provide the minimum required output voltage at the maximum anticipated load with the minimum expected input voltage. In addition, include in the calculations an allowance for the worst-case losses in the rectifiers. Since the turns ratio determined in this manner ordinarily produces a much higher voltage at the secondary under conditions of high input voltage and/or light loading, take care to prevent an overvoltage condition from occurring. Transformers for use with the IC are typically wound on a high-permeability magnetic core. To minimize radiated electromagnetic emissions, select a toroid, pot core, E/I/U core, or equivalent. Diode Selection The high switching speed capability of the MAX258 necessitates high-speed rectifiers. Ordinary silicon signal diodes such as the 1N914 or 1N4148 can be used for lowoutput current levels (less than 50mA), but at high-output current levels, their reverse recovery times might degrade efficiency. At higher output currents, select low forwardvoltage Schottky diodes to improve efficiency. Ensure that the average forward current rating for the rectifier diodes exceeds the maximum load current of the circuit. For surface-mount applications, Schottky diodes such as the B230A, MBRS230, and MBRS320 are recommended. Suggested External Component Manufacturers Table 1. Suggested External Component Manufacturers MANUFACTURER Halo Electronics Diodes Inc. Murata Americas www.maximintegrated.com COMPONENT WEBSITE Transformers www.haloelectronics.com Diodes Capacitors www.diodes.com www.murataamericas.com Maxim Integrated │ 10 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Package Information Ordering Information PART TEMP RANGE PIN-PACKAGE MAX258ATA+ -40°C to +125°C 8 TDFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. Chip Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 8 TDFN-EP T823+1 21-0174 90-0091 PROCESS: BiCMOS www.maximintegrated.com Maxim Integrated │ 11 MAX258 500mA, Push-Pull Transformer Driver for Isolated Power Supplies Revision History REVISION NUMBER REVISION DATE 0 5/13 DESCRIPTION Initial release PAGES CHANGED — For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2013 Maxim Integrated Products, Inc. │ 12