MAXIM MAX7491EEE

19-1768; Rev 0; 7/00
Dual Universal Switched-Capacitor Filters
Features
♦ Dual 2nd-Order Filter in a 16-Pin QSOP Package
♦ High Accuracy
Q Accuracy: ±0.2%
Clock-to-Center Frequency Error: ±0.2%
♦ Rail-to-Rail Input and Output Operation
♦ Single-Supply Operation: +5V (MAX7490)
or +3V (MAX7491)
♦ Internal or External Clock
♦ Highpass, Lowpass, Bandpass, and Notch Filters
♦ Clock-to-Center Frequency Ratio of 100:1
♦ Internal Sampling-to-Center Frequency Ratio
of 200:1
♦ Center Frequency up to 40kHz
♦ Easily Cascaded for Multipole Filters
♦ Low-Power Shutdown: <1µA Supply Current
Ordering Information
________________________Applications
Tunable Active Filters
PART
TEMP. RANGE
Multipole Filters
ADC Anti-Aliasing
Post-DAC Filtering
Adaptive Filtering
SUPPLY
PINVOLTAGE
PACKAGE
(+V)
MAX7490CEE
0°C to +70°C
16 QSOP
5
MAX7490EEE
-40°C to +85°C
16 QSOP
5
MAX7491CEE
0°C to +70°C
16 QSOP
3
MAX7491EEE
-40°C to +85°C
16 QSOP
3
Phase-Locked Loops (PLLs)
Set-Top Boxes
Pin Configuration
TOP VIEW
LPA 1
16 LPB
BPA 2
15 BPB
NA/HPA 3
Typical Application Circuit appears at end of data sheet.
INVA 4
SA 5
14 NB/HPB
MAX7490
MAX7491
SHDN 6
13 INVB
12 SB
11 COM
GND 7
10 EXTCLK
VDD 8
9
CLK
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
QSOP
________________________________________________________________ Maxim Integrated Products
1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX7490/MAX7491
General Description
The MAX7490/MAX7491 consist of two identical lowpower, low-voltage, wide dynamic range, Rail-to-Rail®,
2nd-order switched-capacitor building blocks. Each of
the two filter sections, together with two to four external
resistors, can generate all standard 2nd-order functions: bandpass, lowpass, highpass, and notch (band
reject). Three of these functions are simultaneously
available. Fourth-order filters can be obtained by cascading the two 2nd-order filter sections. Similarly, higher order filters can easily be created by cascading
multiple MAX7490/MAX7491s.
Two clocking options are available: self-clocking
(through the use of an external capacitor) or external
clocking for tighter cutoff frequency control. The clockto-center frequency ratio is 100:1. Sampling is done at
twice the clock frequency, further separating the cutoff
frequency and Nyquist frequency.
The MAX7490/MAX7491 have an internal rail splitter
that establishes a precise common voltage needed for
single-supply operation. The MAX7490 operates from a
single +5V supply and the MAX7491 operates from a
single +3V supply. Both devices feature a low-power
shutdown mode and come in a 16-pin QSOP package.
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
ABSOLUTE MAXIMUM RATINGS
VDD to GND ..............................................................-0.3V to +6V
EXTCLK, SHDN to GND ...........................................-0.3V to +6V
INV_, LP_, BP_, N_/HP_, S_, COM,
CLK to GND............................................-0.3V to (VDD + 0.3V)
Maximum Current into Any Pin ...........................................50mA
Continuous Power Dissipation (TA = +70°C)
16-Pin QSOP (derate 8.30mW/°C above +70°C).........667mW
Operating Temperature Range
MAX749_CEE ....................................................0°C to +70°C
MAX749_EEE ..................................................-40°C to +85°C
Die Temperature ..............................................................+150°C
Storage Temperature.........................................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX7490
(VDD = EXTCLK = +5V, fCLK = 625kHz, TA = TMIN to TMAX, 10kΩ || 50pF load to VDD/2 at LP_, BP_, and N_/HP_, SHDN = VDD, 0.1µF
from COM to GND, 50% duty-cycle clock input, COM = VDD/2. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FILTER
Center Frequency Range
Clock-to-Center Frequency
Accuracy
fO
fCLK/fO
Q Accuracy
0.001 to
40
Mode 1
kHz
Mode 1, R1 = R3 = 50kΩ , R2 = 10kΩ,
Q = 5, deviation from 100:1
±0.2
±0.7
%
Mode 1, R1 = R3 = 50kΩ, R2 = 10kΩ, Q = 5
±0.2
±2
%
fO Temperature Coefficient
±1
ppm/°C
Q Temperature Coefficient
±5
ppm/°C
Mode 1, R1 = R2 = 10kΩ
±0.1
±0.5
VOS1
DC offset of input inverter
±3
±12.5
VOS2
DC offset of 1st integrator
±4
±15
VOS3
DC offset of 2nd integrator
±4
±30
DC Lowpass Gain Accuracy
DC Offset Voltage (Figure 8)
Crosstalk (Note 2)
COM Voltage Range
Input Resistance at COM
fIN = 10kHz
Input: COM externally driven
VDD/2
VDD/2
+ 0.5
Output: COM internally driven
VDD/2
- 0.2
VDD/2
VDD/2
+ 0.2
140
250
325
V
RCOM
Up to 5th harmonic of fCLK
Mode 1, R1 = R2 = R3 =10kΩ, LP output,
Q=1
Noise (Note 3)
Output Voltage Swing
µVRMS
60
µVRMS
±0.1
SHDN = GND, VCOM = 0 to VDD
kΩ
200
0.2
Input Leakage Current at COM
mV
dB
VDD/2
- 0.5
VCOM
Clock Feedthrough
-60
%
VDD - 0.2
V
±10
µA
CLOCK
Maximum Clock Frequency
fCLK
Internal Oscillator Frequency
(Note 4)
fOSC
Clock Input High
2
4
EXTCLK = GND, COSC = 1000pF
95
EXTCLK = GND, COSC = 100pF
135
1.35
VDD - 0.5
_______________________________________________________________________________________
MHz
175
kHz
MHz
V
Dual Universal Switched-Capacitor Filters
(VDD = EXTCLK = +5V, fCLK = 625kHz, TA = TMIN to TMAX, 10kΩ || 50pF load to VDD/2 at LP_, BP_, and N_/HP_, SHDN = VDD, 0.1µF
from COM to GND, 50% duty-cycle clock input, COM = VDD/2. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Clock Input Low
MAX
UNITS
0.5
V
50 ± 5
Clock Duty Cycle
%
SHDN AND EXTCLK
Input High
VIH
Input Low
VIL
Input Leakage Current
VDD - 0.5
V
±0.4
VINPUT = 0 to VDD
0.5
V
±10
µA
5.5
V
4.0
mA
1
µA
POWER REQUIREMENTS
Supply Voltage
VDD
Power-Supply Current
Shutdown Current
IDD
ISHDN
4.5
No external load, mode 1, R1 = R3 = 50kΩ,
R2 = 10kΩ, Q = 5
SHDN = GND
INTERNAL OP AMPS CHARACTERISTICS
Output Short-Circuit Current
Slew Rate
±18
mA
RL ≥ 10kΩ, CL ≤ 50pF
130
dB
GBW
RL ≥ 10kΩ, CL ≤ 50pF
7
MHz
SR
RL ≥ 10kΩ, CL ≤ 50pF
6.4
V/µs
DC Open-Loop Gain
Gain Bandwidth Product
3.5
_______________________________________________________________________________________
3
MAX7490/MAX7491
ELECTRICAL CHARACTERISTICS—MAX7490 (continued)
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
ELECTRICAL CHARACTERISTICS—MAX7491
(VDD = EXTCLK = +3V, fCLK = 625kHz, TA = TMIN to TMAX, 10kΩ || 50pF load to VDD/2 at LP_, BP_, and N_/HP_, SHDN = VDD, 0.1µF
from COM to GND, 50% duty-cycle clock input, COM = VDD/2. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FILTER
Center Frequency Range
Clock-to-Center Frequency
Accuracy
fO
fCLK/fO
Q Accuracy
0.001 to
40
Mode 1
kHz
Mode 1, R1 = R3 = 50kΩ , R2 = 10kΩ,
Q = 5, deviation from 100:1
±0.2
±0.7
%
Mode 1, R1 = R3 = 50kΩ, R2 = 10kΩ,
Q=5
±0.2
±2
%
fO Temperature Coefficient
±1
ppm/°C
Q Temperature Coefficient
±5
ppm/°C
Mode 1, R1 = R2 = 10kΩ
±0.1
±0.5
VOS1
DC offset of input inverter
±3
±12.5
VOS2
DC offset of 1st integrator
±4
±15
DC offset of 2nd integrator
±4
±25
fIN = 10kHz
-60
DC Lowpass Gain Accuracy
DC Offset Voltage
(Figure 8)
VOS3
Crosstalk (Note 2)
COM Voltage Range
Input Resistance at COM
mV
dB
Input: COM externally driven
VDD/2
- 0.1
VDD/2
VDD/2
+ 0.1
Output: COM internally driven
VDD/2
- 0.1
VDD/2
VDD/2
+ 0.1
60
80
120
VCOM
%
V
RCOM
kΩ
Clock Feedthrough
Up to 5th harmonic of fCLK
200
µVRMS
Noise (Note 3)
Mode 1, R1= R2 = R3 = 10kΩ,
LP output, Q = 1
60
µVRMS
Output Voltage Swing
0.2
±0.1
SHDN = GND, VCOM = 0 to VDD
Input Leakage Current at COM
VDD - 0.2
V
±10
µA
CLOCK
Maximum Clock Frequency
Internal Oscillator Frequency
(Note 4)
fCLK
fOSC
4
EXTCLK = GND, COSC = 1000pF
95
EXTCLK = GND, COSC = 100pF
Clock Input High
135
MHz
175
1.35
VDD - 0.5
V
Clock Input Low
0.5
50 ±5
Clock Duty Cycle
kHz
MHz
V
%
SHDN AND EXTCLK
Input High
VIH
Input Low
VIL
Input Leakage Current
4
VDD - 0.5
VINPUT = 0 to VDD
V
±0.4
_______________________________________________________________________________________
0.5
V
±10
µA
Dual Universal Switched-Capacitor Filters
(VDD = EXTCLK = +3V, fCLK = 625kHz, TA = TMIN to TMAX, 10kΩ || 50pF load to VDD/2 at LP_, BP_, and N_/HP_, SHDN = VDD, 0.1µF
from COM to GND, 50% duty-cycle clock input, COM = VDD/2. Typical values are at TA = +25°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
3.6
V
4.0
mA
1
µA
POWER REQUIREMENTS
Supply Voltage
VDD
Power-Supply Current
IDD
Shutdown Current
2.7
No load, mode 1, R1 = R3 = 50kΩ,
R2 = 10kΩ, Q = 5
3.5
SHDN = GND
ISHDN
INTERNAL OP AMPS CHARACTERISTICS
±11
Output Short-Circuit Current
RL ≥ 10kΩ, CL ≤ 50pF
130
dB
GBW
RL ≥ 10kΩ, CL ≤ 50pF
7
MHz
SR
RL ≥ 10kΩ, CL ≤ 50pF
6
V/µs
DC Open-Loop Gain
Gain Bandwidth Product
Slew Rate
mA
Note 1: Resistive loading of the N_/HP_, LP_, BP_ outputs includes the resistors used for the filter implementation.
Note 2: Crosstalk between internal filter sections is measured by applying a 1VRMS 10kHz signal to one bandpass filter section input
and grounding the input of the other bandpass filter section. The crosstalk is the ratio between the output of the grounded
filter section and the 1VRMS input signal of the other section.
Note 3: Bandwidth of noise measurement is 80kHz.
Note 4: fOSC (kHz) = 135 x 103 / COSC (COSC in pF)
Typical Operating Characteristics
(VDD = +5V for MAX7490, VDD = +3V for MAX7491, fCLK = 625kHz, SHDN = EXTCLK = VDD, COM = VDD/2, Mode 1, R3 = R1 = 50kΩ,
R2 = 10kΩ, Q = 5, TA = +25°C, unless otherwise noted.)
2ND-ORDER BANDPASS FILTER
FREQUENCY RESPONSE
200
PHASE (%)
GAIN (dB)
-10
-20
-30
150
100
-40
VDD = +5V
fCLK = 625kHz
Q=5
50
-50
-60
0
1
10
FREQUENCY (kHz)
100
1
MAX7490-03
250
-0.1
fCLK/fO DEVIATION (%)
0
fCLK/fO DEVIATION vs. fCLK
0
MAX7490-02
300
MAX7490-01
10
2ND-ORDER BANDPASS FILTER
PHASE RESPONSE
-0.2
VDD = 5V
-0.3
VDD = 3V
-0.4
-0.5
-0.6
-0.7
-0.8
10
FREQUENCY (kHz)
100
100
1000
10,000
fCLK (kHz)
_______________________________________________________________________________________
5
MAX7490/MAX7491
ELECTRICAL CHARACTERISTICS—MAX7491 (continued)
Typical Operating Characteristics (continued)
(VDD = +5V for MAX7490, VDD = +3V for MAX7491, fCLK = 625kHz, SHDN = EXTCLK = VDD, COM = VDD/2, Mode 1, R3 = R1 = 50kΩ,
R2 = 10kΩ, Q = 5, TA = +25°C, unless otherwise noted.)
VDD = 3V
-0.2
-0.3
-0.4
-0.5
-0.6
20
40
60
80
-1
-6
-15
Q DEVIATION vs. TEMPERATURE
10
35
60
85
100
1000
NOISE vs. Q
SUPPLY CURRENT vs. TEMPERATURE
3.7
MAX7490-08
450
3.6
400
1.0
-0.5
300
IDD (mA)
NOISE (µVRMS)
0
250
200
150
-1.0
VDD = 3V
3.5
350
0.5
10,000
fCLK (kHz)
500
MAX7490-07
1.5
MAX7490-06
-3
TEMPERATURE (°C)
2.0
3.4
VDD = 5V
3.3
3.2
100
-1.5
3.1
50
-2.0
3.0
0
-40
-15
10
35
60
0
85
20
40
60
80
-40
100
-15
10
35
60
Q
TEMPERATURE (°C)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
SUPPLY CURRENT vs. SUPPLY VOLTAGE
MAX7491
THD + NOISE vs. FREQUENCY
3.41
MAX7490-10
4.0
3.9
3.40
3.8
-20
-30
+85°C
fCLK = 3MHz
IDD (mA)
3.5
fCLK = 625kHz
3.4
3.37
+25°C
3.36
-40°C
3.35
3.3
THD + NOISE (dB)
3.38
3.6
-50
-60
-80
-90
-100
3.1
3.33
-110
3.0
3.32
3.0
3.5
4.0
4.5
VDD (V)
5.0
5.5
B
A
-70
3.34
fCLK = 2kHz
3.2
A = MODE 1
B = MODE 3
-40
3.39
3.7
85
MAX7490-12
TEMPERATURE (°C)
MAX7490-11
Q DEVIATION (%)
-2
-5
Q
6
VDD = 3V
-4
-40
100
VDD = 5V
0
MAX7490-09
0
Q DEVIATION vs. fCLK
1
Q DEVIATION (%)
-0.1
fCLK/fO DEVIATION (%)
fCLK/fO DEVIATION (%)
0
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
MAX7490-05
VDD = 5V
0.1
fCLK/fO DEVIATION vs. TEMPERATURE
MAX7490-04
fCLK/fO DEVIATION vs. Q
0.2
IDD (mA)
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
-120
3.0
3.5
4.0
4.5
VDD (V)
5.0
5.5
1k
10k
INPUT FREQUENCY (Hz)
_______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
MAX7490
THD + NOISE vs. INPUT VOLTAGE
A = MODE 1
B = MODE 3
-20
-10
MAX7490-14
A = MODE 1
B = MODE 3
-30
-10
MAX7490-13
-20
MAX7491
THD + NOISE vs. INPUT VOLTAGE
MAX7490-15
MAX7490
THD + NOISE vs. FREQUENCY
A = MODE 1
B = MODE 3
-20
-40
THD + NOISE (dB)
B
-70
-80
A
-40
-50
-60
B
-90
-70
-100
-110
-80
-120
-90
1k
10k
-60
B
-80
A
-90
0
0.5
1.0
1.5
2.0
2.5
3.0
0
1
2
3
4
5
INPUT VOLTAGE (Vp-p)
INPUT VOLTAGE (Vp-p)
OUTPUT VOLTAGE SWING vs. RLOAD
INTERNAL OSCILLATOR PERIOD
vs. SMALL CAPACITANCE
INTERNAL OSCILLATOR PERIOD
vs. LARGE CAPACITANCE
4.0
3.5
VDD = 3V
3.0
2.5
2000
1500
1000
VDD = 3V
500
VDD = 5V
2.0
12
16
20
0
200
RLOAD (kΩ) TO COM
400
600
800
80
VDD = 3V
60
40
VDD = 5V
20
1
1000
2
COSC = 1000pF
132
3
4
5
6
7
CAPACITANCE (nF)
INTERNAL OSCILLATOR FREQUENCY
vs. TEMPERATURE
MAX7490-19
INTERNAL OSCILLATOR FREQUENCY (kHz)
100
CAPACITANCE (pF)
INTERNAL OSCILLATOR FREQUENCY
vs. SUPPLY VOLTAGE
133
120
131
130
129
128
127
144
142
MAX7490-20
8
140
0
0
4
MAX7490-18
INTERNAL OSCILLATOR FREQUENCY (kHz)
INTERNAL OSCILLATOR FREQUENCY (kHz)
VDD = 5V
160
MAX7490-17
2500
MAX7490-16
4.5
OUTPUT SWING (Vp-p)
-50
INPUT FREQUENCY (Hz)
5.0
0
-40
-70
A
INTERNAL OSCILLATOR FREQUENCY (kHz)
THD + NOISE (dB)
-60
-30
THD + NOISE (dB)
-30
-50
COSC = 1000pF
140
138
VDD = 3V
136
134
132
VDD = 5V
130
128
126
124
126
3.0
3.5
4.0
4.5
VDD (V)
5.0
5.5
-40
-15
10
35
60
85
TEMPERATURE (°C)
_______________________________________________________________________________________
7
MAX7490/MAX7491
Typical Operating Characteristics (continued)
(VDD = +5V for MAX7490, VDD = +3V for MAX7491, fCLK = 625kHz, SHDN = EXTCLK = VDD, COM = VDD/2, Mode 1, R3 = R1 = 50kΩ,
R2 = 10kΩ, Q = 5, TA = +25°C, unless otherwise noted.)
Dual Universal Switched-Capacitor Filters
MAX7490/MAX7491
Pin Description
NAME
PIN
FUNCTION
FILTER A
FILTER B
LP_
1
16
2nd-Order Lowpass Filter Output
BP_
2
15
2nd-Order Bandpass Filter Output
N_/HP_
3
14
2nd-Order Notch/Highpass Filter Output
INV_
4
13
Inverting Input of Filter Summing Op Amp
S_
5
12
Summing Input. The connection of the summing input, along with the other
resistor connections, determine the circuit topology (mode) of each 2ndorder section. S_ must never be left floating.
SHDN
6
Shutdown Input. Drive SHDN low to enable shutdown mode; drive high or
connect to VDD for normal operation.
GND
7
Ground Pin
VDD
8
Positive Supply. VDD should be bypassed with a 0.1µF capacitor to GND. A
low-noise supply is recommended. Input +5V for MAX7490 or +3V for
MAX7491.
CLK
9
Clock Input. Connect to an external capacitor (COSC) between CLK and
ground to set the internal oscillator frequency. For external clock operation,
drive with a CMOS-level clock. The duty cycle of the external clock should be
between 45% and 55% for best performance.
EXTCLK
10
External/Internal Clock Select Input. Connect EXTCLK to VDD when driving
CLK externally. Connect to GND when using the internal oscillator.
COM
11
Common Pin. Biased internally at VDD/2. Bypass externally to GND with
0.1µF capacitor. To override the internal biasing, drive with an external lowimpedance source.
_______________Detailed Description
The MAX7490/MAX7491 are universal switched-capacitor filters designed with a fixed internal fCLK/fO ratio of
100:1. Operating modes use external resistors connected in different arrangements to realize different filter
functions (highpass, lowpass, bandpass, notch) in all of
the classical filter topologies (Butterworth, Bessel, elliptic, Chebyshev). Figure 1 shows a block diagram.
Clock Signal
External Clock
The MAX7490/MAX7491 switched-capacitor filters are
designed for use with external clocks that have a 50%
±5% duty cycle. When using an external clock, drive
the EXTCLK pin high or connect to VDD. Drive CLK with
CMOS logic levels (GND and VDD). Varying the rate of
8
the external clock adjusts the center frequency of the
filter:
fO = fCLK /100
Internal Clock
When using the internal oscillator, drive the EXTCLK pin
low or connect to GND and connect a capacitor (COSC)
between CLK and GND. The value of the capacitor
(COSC) determines the oscillator frequency as follows:
fOSC (kHz) = 135 x 103 / COSC (pF)
Since COSC is in the low picofarads, minimize the stray
capacitance at CLK so that it does not affect the internal oscillator frequency. Varying the frequency of the
internal oscillator adjusts the filter’s center frequency by
a 100:1 clock-to-center frequency ratio. For example,
an internal oscillator frequency of 135kHz produces a
nominal center frequency of 1.35kHz.
_______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
MAX7490/MAX7491
SHDN
(6)
VDD (8)
INVA (4)
BPA (2)
NA/HPA (3)
+
R
Σ
-
∫
LPA (1)
∫
COM (11)
NB/HPB (14) SA (5)
+
R
INVB (13)
Σ
-
BPB (15)
∫
LPB (16)
∫
GND (7)
CLK (9)
SB (12)
EXTCLK (10)
Figure 1. Block Diagram
2nd-Order Filter Stage
The MAX7490/MAX7491 are dual biquad filters. The
biquad topology allows the use of standard filter tables
and equations to implement simultaneous lowpass,
bandpass, and notch or highpass filters. Topologies
such as Butterworth, Chebyshev, Bessel, elliptic, as
well as custom algorithms are possible.
Internal Common Voltage
able to swing to within approximately 0.2V of either
supply.
Driving coaxial cable, large capacitive loads, or total
resistive loads less than 10kΩ will degrade the total
harmonic distortion (THD) performance. Note that the
effective resistive load at the output must include both
the feedback resistors and any external load resistors.
Low-Power Shutdown Mode
The COM pin sets the common-mode input voltage and
is internally biased to VDD/2 with a resistor-divider. The
resistors used are typically 250kΩ for the MAX7490,
and typically 80kΩ for the MAX7491. The commonmode voltage is easily overdriven by an external voltage supply if desired. The COM pin should be
bypassed to the analog ground with at least a 0.1µF
capacitor.
The MAX7490/MAX7491 have a shutdown mode that is
activated by driving SHDN low. In shutdown mode, the
filter supply current reduces to <1µA (max), and the filter outputs become high impedance. The COM input
also becomes high impedance during shutdown. For
normal operation, drive SHDN high or connect to VDD.
Inverting Inputs
Designing with the MAX7490/MAX7491 begins by
selecting the mode that best fits the desired circuit
requirements. Table 1 lists the available modes and
their relative advantages and disadvantages. Table 2
lists the different nomenclature used in the explanations
that follow.
Locate resistors that are connected to INV_ as close as
possible to INV_ to reduce stray capacitance and noise
pickup. INV_ are inverting inputs to continuous-time op
amps, and behave like a virtual ground. There is no
sampling energy present on these inputs.
Outputs
Each switched-capacitor section, together with two to
four external resistors, can generate all standard 2ndorder functions: bandpass, lowpass, highpass, and
notch (band-reject) functions. Three of these functions
are simultaneously available. The maximum signal
swing is limited by the power-supply voltages used.
The amplifiers’ outputs in the MAX7490/MAX7491 are
__________Applications Information
Mode 1
Figure 2 shows the MAX7490/MAX7491s’ configuration
of Mode 1. This mode provides 2nd-order notch, lowpass, and bandpass filter functions. The gain at all
three outputs is inversely proportional to the value of
R1. The center frequency, fO, is fixed at fCLK/100. HighQ bandpass filters can be built without exceeding the
bandpass amplifier’s output swing (i.e., HOBP does not
_______________________________________________________________________________________
9
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
Table 1. Filter Operating Modes
MODE
LP
1
HP
BP
N
LP-N*
HP-N*
•
•
•
fCLK/fO ratio is the nominal value. Good for bandpass filters
with identical sections cascaded, higher order Butterworth filters,
high-Q bandpass, low-Q notches.
1B
•
•
•
Same as Mode 1 with fCLK/fO ratios greater than the nominal
value.
2
•
•
•
Combination of Mode 1 and Mode 3; fCLK/fO ratios always
less than the nominal value. Less sensitivity to resistor tolerances
than Mode 3.
Extension of Mode 2 that allows higher frequencies. Highpass
and lowpass outputs are summed with external op amp and
two resistors. Good for lowpass elliptic filters.
•
2N
3
•
•
•
3A
•
•
•
COMMENTS
Adjustable fO above and below the nominal frequency.
Commonly used for multiple-pole Chebyshev filters, all-pole
higher order bandpass, lowpass, and highpass filters.
•
•
Extension of Mode 3 that needs an external op amp and
two additional resistors. Commonly used for lowpass or higher
elliptic or Cauer filters.
* LP-N = lowpass notch, HP-N = highpass notch. Both require an external op amp. See Definition of Terms (Table 2).
Table 2. Definition of Terms
TERM
fCLK
fO
fNOTCH
Q
10
DEFINITION
The clock frequency applied to the switched-capacitor filter.
The center frequency of the 2nd-order complex pole pair, fO, is determined by measuring the peak response
frequency at the bandpass output.
The frequency of minimum amplitude response at the notch output.
Quality factor, or Q, is the ratio of fO to the -3dB bandwidth of the 2nd-order bandpass filter. Q also determines
the amount of amplitude peaking at the lowpass and highpass outputs, but is not measured at these outputs.
HOBP
The gain in V/V of the bandpass output at f = fO.
HOLP
The gain in V/V of the lowpass output at f→0Hz.
HOHP
The gain in V/V of the highpass output at f→fCLK/2.
HON1
The notch output gain as f→0Hz.
HON2
The notch output gain at f = fCLK/2.
LP-N
A notch output with HON1 > HON2.
HP-N
A notch output with HON1 < HON2.
______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
R6
R3
R3
R2
N
S
BP
LP
R5
COM
R2
N
R1
VIN
+
S
BP
LP
R1
-
∫
Σ
∫
COM
VIN
+
-
∫
Σ
∫
COM
Figure 2. Mode 1, 2nd-Order Filter Providing Notch, Bandpass,
and Lowpass Outputs
Figure 3. Mode 1B, 2nd-Order Filter Providing Notch, Bandpass,
and Lowpass Outputs
have to track Q). The notch and bandpass center frequencies are identical. The notch output gain is the
same above and below the notch center frequency.
Mode 1 can also be used to make high-order Butterworth lowpass filters, low Q notches, and multiple-order
bandpass filters obtained by cascading identical
switched-capacitor sections.
Mode 1 Design Equations
Mode 1B Design Equations
fO =
fCLK
R2
HOBP =
R3
R2
HOBP =
R3
HOLP =
Q=
HOLP =
100
fnotch = fO
Q=
f
fO = CLK
100
fn = fO
R6
R6 + R5
R6
R6 + R5
R6 + R5
−R2
R1
R6
−R 3
R1
HON1(as f → 0Hz) =
−R2
R1
−R 3
−R2
R1
HON2 (at f = fCLK / 2) =
−R2
R1
R1
HON1(as f → 0Hz) =
−R2
R1
HON2 (at f = fCLK / 2) =
−R2
R1
Mode 1B
Figure 3 shows the configuration of Mode 1B. R5 and
R6 are added to lower the feedback voltage from the
lowpass output to the summing input. This allows the
clock-to-center frequency to be adjusted beyond the
nominal value. This mode essentially has the same
functions and speed as Mode 1 while providing a highQ with fCLK/fO ratios greater than the nominal value.
Mode 2
Figure 4 shows the configuration of Mode 2. Mode 2 is
a combination of Mode 1 and Mode 3. In this mode,
fCLK/fO is always less than the part’s nominal ratio.
However, it provides less sensitivity to resistor tolerances than does Mode 3. It has a highpass notch output where the notch frequency depends solely on the
clock frequency.
______________________________________________________________________________________
11
MAX7490/MAX7491
CC
CC
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
Mode 2 Design Equations
fO =
fCLK
100
1+
CC
R2
R4
R4
R3
f
fn = CLK
100
Q=
R3
R2
R2
HP/N
1+
R2
VIN
R4
R4 
−R2 
HOLP =


R1  R4 + R2 
HOBP =
S
BP
+
-
Σ
∫
∫
COM
−R 3
R1
−R2 
Figure 4. Mode 2, 2nd-Order Filter Providing a Highpass
Notch, Bandpass, and Lowpass Outputs

HON1( f → 0Hz) =


R1  R4 + R2 
HON2 (at f = fCLK / 2) =
R4
Mode 2N Design Equations
−R2
Mode 2N
Figure 5 shows the configuration of Mode 2N. This
mode extends the topology of Mode 3A to Mode 2,
where the highpass and lowpass outputs are summed
through two external resistors, RH and RL, to create a
lowpass notch filter that has higher frequency than the
one in Mode 2. Mode 2 is most useful in lowpass elliptic
designs. When cascading the sections of the
MAX7490/MAX7491, the highpass and lowpass outputs
can be summed directly into the inverting input of the
next section. Only one external op amp is needed.
f
fO = CLK
100
1+
f
fn = CLK
100
R
1+ H
RL
Q=
R3
R2
1+
R2
R4
R2
R4
R
R 
HON1(f → 0Hz) =  G + G 
 RH RL 
 R2   R4 

  
 R1   R4 + R2 
CC
R4
R3
R2
HP/N
S
BP
LP
R1
-
VIN
+
COM
Σ
∫
∫
RG
RL
LOWPASS
NOTCH
OUTPUT
RH
COM
Figure 5. Mode 2N, 2nd-Order Filter Providing a Lowpass Notch Output
12
LP
R1
______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
R4
R3
R2
HP
VIN
BP
S
LP
COM
R1
+
-
Σ
∫
∫
COM
R2
R4
f
fO = CLK
100
CC
Figure 6. Mode 3, 2nd-Order Section Providing Highpass,
Bandpass, and Lowpass Outputs
R3 R2
R2 R4
−R2
HOHP =
R1
−R4
HOLP =
R1
−R3
HOBP =
R1
Q=
Mode 3A
Figure 7 shows the configuration of Mode 3A. Similar to
Mode 2, this mode adds an external op amp. See
Table 3 for op amp selection ideas. This op amp creates a highpass notch and lowpass notch by summing
the highpass and lowpass outputs through two external
resistors, RH and RL. The ratio of resistors RH and RL
adjusts the notch frequency, while R2 and R4 adjust
the bandpass center frequency, since the notch (zero
pair) frequency can be adjusted to both above and
below fO. Mode 3A is suitable for both lowpass and
highpass elliptic or Cauer filters. In multipole elliptic filters, only one external op amp is needed. Use the
inverting input of the internal op amp as the summing
node for all but the final section of the filter.
CC
R4
R3
R2
S
N/HP
BP
LP
COM
R1
-
VIN
+
Σ
RG
RL
COM
LOWPASS
NOTCH
OUTPUT
RH
COM
Figure 7. Mode 3A, 2nd-Order Filter Providing Highpass Notch or Lowpass Notch Outputs
______________________________________________________________________________________
13
MAX7490/MAX7491
Mode 3
Figure 6 shows the configuration of Mode 3. This mode
is a sampled time (Z transform) equivalent of the classical 2nd-order state variable filter. In this versatile mode,
the ratio of resistors R2 and R4 can move the center
frequency both above and below the nominal ratio.
Mode 3 is commonly used to make multiple-pole
Chebyshev filters with a single clock frequency. This
mode can also be used to make high-order all-pole
bandpass, lowpass, and highpass filters.
Mode 3 Design Equations
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
Table 3. Suggested External Op Amps
PART
GBW (MHz)
SLEW RATE (V/µs)
MAX4281
2
0.7
ISUPPLY/AMP (mA)
0.5
PIN-PACKAGE
5 SOT23
5 SOT23
MAX4322
5
2.0
1.1
MAX4130
10
4.0
1.15
5 SOT23
MAX4490
10
10.0
2.0
5 SOT23
Offset Voltage
Mode 3A Design Equations
f
fO = CLK
100
R2
R4
f
fn = CLK
100
Q=
RH
RL
R3
R2
R2
R4
−R2
HOHP =
HOLP =
HOBP =
Switched-capacitor integrators generally exhibit higher
input offsets than discrete RC integrators. The larger
offset is mainly due to the charge injection of the
CMOS switches into the integrating capacitors. The
internal op amp offset also adds to the overall offset
value. Figure 8 shows the input offsets from a single
2nd-order section. Table 4 lists the formula for the output offset voltage for various modes and output pins.
Power Supplies
The MAX7490 operates from a single +5V supply, and
the MAX7491 operates from a single +3V supply.
Bypass VDD to GND with at least a 0.1µF capacitor.
VDD should be isolated from other digital or high-voltage analog supplies. If dual supplies are required,
connect the COM pin to the system ground and the
GND pin to the negative supply. Figure 9 shows an
example of dual-supply operation. Single-supply and
dual-supply performances are equivalent. For dualsupply operation, drive CLK, SHDN, and EXTCLK from
GND (which is now V-) to VDD. If using the internal
oscillator in dual-supply mode, COSC can be returned
to either GND or the actual ground voltage. Use the
MAX7490 for ±2.5V and use the MAX7491 for ±1.5V.
For most applications, a 0.1µF bypass capacitor from
COM to GND is sufficient. If the VDD supply has significant 60Hz energy, increase this capacitor to 1µF or
greater to provide better power-supply rejection.
R1
−R4
R1
−R 3
R1
HON1(f → 0Hz) =
RG  R4 


RL  R1 
HON2 (at f = fCLK / 2) =
RG  R2 
 
RH  R1 
Note: When the passband gain error exceeds 1dB, the
use of capacitor CC between the lowpass output and
the inverting input will reduce the gain error. The value
can best be determined experimentally. Typically, it
should be about 5pF/dB (CC-MAX = 15pF).
INV
BP
N/HP
+
COM
LP
VOS1
Σ
VOS2
-
∫
VOS3
∫
S
Figure 8. Block Diagram of a 2nd-Order Section Showing the Input Offsets
14
______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
MODE
VOSN/HP
VOSBP
VOSLP
1
VOS1[1 + (R2 / R3) + (R2 / R1)] - (VOS3)
(R2 / R3)
VOS3
VOSN/HP - VOS2
1b
VOS1[1 + (R2 / R3) + (R2 / R1)] - (VOS3)
(R2 / R3)
VOS3
(VOSN/HP - VOS2)[1 + R5 / R6)]
2
VOS1[1 + (R2 / R3) + (R2 / R1) + (R2 / R4) (VOS3)(R2 / R3)][R4 / R2 + R4] +
(VOS2)[R2 / R2 + R4]
VOS3
VOSN/HP - VOS2
3
VOS2
VOS3
VOS1[1 + (R4 / R1) + (R4 / R2) + (R4 / R3)] - (VOS2)
(R4 / R2) - (VOS3)(R4 / R3)
Aliasing
V+
VDD
*
SHDN
0.1µF
COM
V+
V-
CLOCK
CLK
MAX7490
MAX7491
0.1µF
GND
*DRIVE SHDN TO V- FOR LOW-POWER
SHUTDOWN MODE.
V-
Figure 9. Dual-Supply Operation
Input Signal Amplitude Range
The optimal input signal range is determined by
observing the voltage level at which the signal-to-noise
plus distortion (SINAD) ratio is maximized for a given
corner frequency. The Typical Operating Characteristics show the THD + Noise response as the input signal’s peak-to-peak amplitude is varied. In most
systems, the input signal should be kept as large as
possible to maximize the signal-to-noise ratio (SNR).
Allow sufficient headroom to ensure no signal clipping
under expected operating conditions.
Anti-Aliasing and Post-DAC Filtering
When using the MAX7490/MAX7491 for anti-aliasing or
post-DAC filtering, synchronize the DAC (or ADC) and
the filter clocks. If the clocks are not synchronized,
beat frequencies may alias into the desired passband.
Aliasing is an inherent phenomenon of most switchedcapacitor filters. As with all sampled systems, frequency components of the input signal above one half the
sampling rate will be aliased. The MAX7490/MAX7491
sample at twice the clock frequency, yielding a 200:1
sampling to cutoff frequency ratio.
In particular, input signal components (fIN) near the
sampling rate generate a difference frequency
(fSAMPLING - fIN) that often falls within the passband of
the filter. Such aliased signals, when they appear at the
output, are indistinguishable from real input information. For example, the aliased output signal generated
when a 99kHz waveform is applied to a filter sampling
at 100kHz, (fCLK = 50kHz) is 1kHz. This waveform is an
attenuated version of the output that would result from
a true 1kHz input. Since sampling is done at twice the
clock frequency, the Nyquist frequency is the same as
the clock frequency.
A simple passive RC lowpass input filter is usually sufficient to remove input frequencies that can be aliased.
In many cases, the input signal itself may be band limited and require no special anti-alias filtering. Selecting
a passive filter cutoff frequency equal to fC/2 gives
12dB rejection at the Nyquist frequency.
Clock Feedthrough
Clock feedthrough is defined as the RMS value of the
clock frequency and its harmonics that are present at
the filter’s output pins, even without input signal. The
clock feedthrough can be greatly reduced by adding a
simple RC lowpass network at the final filter output.
Choose a cutoff frequency as low as possible to provide maximum noise attenuation. The attenuation and
phase shift of the external filter will limit the actual frequency selected.
______________________________________________________________________________________
15
MAX7490/MAX7491
Table 4. Output DC Offsets for a 2nd-Order Section
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
Table 5. Cascading Identical Bandpass
Filter Sections
TOTAL SECTIONS
TOTAL BW
TOTAL Q
1
1.000 B
1.00 Q
2
0.644 B
1.55 Q
3
0.510 B
1.96 Q
4
0.435 B
2.30 Q
5
0.386 B
2.60 Q
Multiple Filter Stages
In some designs, such as very narrow band filters, or in
modes where fO cannot be tuned with resistors, several
2nd-order sections with identical fO may be cascaded
without multiple feedback. The total Q of the resultant
filter (QT) is:
Total QT = Q / (2N - 1)1/2
Q is the Q of each individual filter section, and N is the
number of 2nd-order sections. In Table 5, the total Q
and total bandwidth (BW) are listed for up to five identical 2nd-order sections. B is the bandwidth of each section.
Wideband Noise
The wideband noise of the filter is the total RMS value
of the device’s noise spectral density and is used to
determine the operating SNR. Most of its frequency
contents lie within the filter’s passband and cannot be
reduced with postfiltering. The total noise depends
mainly on the Q of each filter section and the cascade
sequence. Therefore, in multistage filters, the section
with the highest Q should be placed first for lower output noise.
16
Chip Information
TRANSISTOR COUNT: 1439
TECHNOLOGY: BiCMOS
______________________________________________________________________________________
Dual Universal Switched-Capacitor Filters
4TH-ORDER 10kHz
BANDPASS FILTER
R3A
200k
R1B
200k
LPA
LPB
BPA
BPB
R2A
10k
NA/HPA
R1
200k
4TH-ORDER 10kHz BANDPASS FILTER
FREQUENCY RESPONSE
R3B
200k
MAX7490
MAX7491
5
OUT
0
R2B
10k
-5
NB/HPB
INVA
SA
GAIN (dB)
-10
VIN
INVB
SB
-15
-20
-25
SHDN
-30
COM
GND
EXTCLK
VDD
CLK
C2
0.1µF
-35
-40
8
VDD
fCLK = 1MHz
9
10
11
12
FREQUENCY (kHz)
C1
0.1µF
______________________________________________________________________________________
17
MAX7490/MAX7491
Typical Application Circuit
MAX7490/MAX7491
Dual Universal Switched-Capacitor Filters
QSOP.EPS
Package Information
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.